diff options
Diffstat (limited to 'arch/m68k/kernel/head.S')
| -rw-r--r-- | arch/m68k/kernel/head.S | 29 |
1 files changed, 19 insertions, 10 deletions
diff --git a/arch/m68k/kernel/head.S b/arch/m68k/kernel/head.S index d197e7ff62c..ac85f16534a 100644 --- a/arch/m68k/kernel/head.S +++ b/arch/m68k/kernel/head.S @@ -2752,11 +2752,9 @@ func_return get_new_page #ifdef CONFIG_MAC L(scc_initable_mac): - .byte 9,12 /* Reset */ .byte 4,0x44 /* x16, 1 stopbit, no parity */ .byte 3,0xc0 /* receiver: 8 bpc */ .byte 5,0xe2 /* transmitter: 8 bpc, assert dtr/rts */ - .byte 9,0 /* no interrupts */ .byte 10,0 /* NRZ */ .byte 11,0x50 /* use baud rate generator */ .byte 12,1,13,0 /* 38400 baud */ @@ -2899,6 +2897,7 @@ func_start serial_init,%d0/%d1/%a0/%a1 is_not_mac(L(serial_init_not_mac)) #ifdef SERIAL_DEBUG + /* You may define either or both of these. */ #define MAC_USE_SCC_A /* Modem port */ #define MAC_USE_SCC_B /* Printer port */ @@ -2908,9 +2907,21 @@ func_start serial_init,%d0/%d1/%a0/%a1 #define mac_scc_cha_b_data_offset 0x4 #define mac_scc_cha_a_data_offset 0x6 +#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B) + movel %pc@(L(mac_sccbase)),%a0 + /* Reset SCC device */ + moveb #9,%a0@(mac_scc_cha_a_ctrl_offset) + moveb #0xc0,%a0@(mac_scc_cha_a_ctrl_offset) + /* Wait for 5 PCLK cycles, which is about 68 CPU cycles */ + /* 5 / 3.6864 MHz = approx. 1.36 us = 68 / 50 MHz */ + movel #35,%d0 +5: + subq #1,%d0 + jne 5b +#endif + #ifdef MAC_USE_SCC_A /* Initialize channel A */ - movel %pc@(L(mac_sccbase)),%a0 lea %pc@(L(scc_initable_mac)),%a1 5: moveb %a1@+,%d0 jmi 6f @@ -2922,9 +2933,6 @@ func_start serial_init,%d0/%d1/%a0/%a1 #ifdef MAC_USE_SCC_B /* Initialize channel B */ -#ifndef MAC_USE_SCC_A /* Load mac_sccbase only if needed */ - movel %pc@(L(mac_sccbase)),%a0 -#endif /* MAC_USE_SCC_A */ lea %pc@(L(scc_initable_mac)),%a1 7: moveb %a1@+,%d0 jmi 8f @@ -2933,6 +2941,7 @@ func_start serial_init,%d0/%d1/%a0/%a1 jra 7b 8: #endif /* MAC_USE_SCC_B */ + #endif /* SERIAL_DEBUG */ jra L(serial_init_done) @@ -3006,17 +3015,17 @@ func_start serial_putc,%d0/%d1/%a0/%a1 #ifdef SERIAL_DEBUG -#ifdef MAC_USE_SCC_A +#if defined(MAC_USE_SCC_A) || defined(MAC_USE_SCC_B) movel %pc@(L(mac_sccbase)),%a1 +#endif + +#ifdef MAC_USE_SCC_A 3: btst #2,%a1@(mac_scc_cha_a_ctrl_offset) jeq 3b moveb %d0,%a1@(mac_scc_cha_a_data_offset) #endif /* MAC_USE_SCC_A */ #ifdef MAC_USE_SCC_B -#ifndef MAC_USE_SCC_A /* Load mac_sccbase only if needed */ - movel %pc@(L(mac_sccbase)),%a1 -#endif /* MAC_USE_SCC_A */ 4: btst #2,%a1@(mac_scc_cha_b_ctrl_offset) jeq 4b moveb %d0,%a1@(mac_scc_cha_b_data_offset) |