diff options
Diffstat (limited to 'arch/mips/alchemy/common')
| -rw-r--r-- | arch/mips/alchemy/common/platform.c | 28 | ||||
| -rw-r--r-- | arch/mips/alchemy/common/power.c | 35 |
2 files changed, 28 insertions, 35 deletions
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c index 1dc55ee2681..3691630931d 100644 --- a/arch/mips/alchemy/common/platform.c +++ b/arch/mips/alchemy/common/platform.c @@ -24,6 +24,33 @@ #include <prom.h> +static void alchemy_8250_pm(struct uart_port *port, unsigned int state, + unsigned int old_state) +{ + switch (state) { + case 0: + if ((__raw_readl(port->membase + UART_MOD_CNTRL) & 3) != 3) { + /* power-on sequence as suggested in the databooks */ + __raw_writel(0, port->membase + UART_MOD_CNTRL); + wmb(); + __raw_writel(1, port->membase + UART_MOD_CNTRL); + wmb(); + } + __raw_writel(3, port->membase + UART_MOD_CNTRL); /* full on */ + wmb(); + serial8250_do_pm(port, state, old_state); + break; + case 3: /* power off */ + serial8250_do_pm(port, state, old_state); + __raw_writel(0, port->membase + UART_MOD_CNTRL); + wmb(); + break; + default: + serial8250_do_pm(port, state, old_state); + break; + } +} + #define PORT(_base, _irq) \ { \ .mapbase = _base, \ @@ -33,6 +60,7 @@ .flags = UPF_SKIP_TEST | UPF_IOREMAP | \ UPF_FIXED_TYPE, \ .type = PORT_16550A, \ + .pm = alchemy_8250_pm, \ } static struct plat_serial8250_port au1x00_uart_data[] = { diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c index 5ef06a164a8..e5916a516e5 100644 --- a/arch/mips/alchemy/common/power.c +++ b/arch/mips/alchemy/common/power.c @@ -49,11 +49,6 @@ * We only have to save/restore registers that aren't otherwise * done as part of a driver pm_* function. */ -static unsigned int sleep_uart0_inten; -static unsigned int sleep_uart0_fifoctl; -static unsigned int sleep_uart0_linectl; -static unsigned int sleep_uart0_clkdiv; -static unsigned int sleep_uart0_enable; static unsigned int sleep_usb[2]; static unsigned int sleep_sys_clocks[5]; static unsigned int sleep_sys_pinfunc; @@ -62,22 +57,6 @@ static unsigned int sleep_static_memctlr[4][3]; static void save_core_regs(void) { - extern void save_au1xxx_intctl(void); - extern void pm_eth0_shutdown(void); - - /* - * Do the serial ports.....these really should be a pm_* - * registered function by the driver......but of course the - * standard serial driver doesn't understand our Au1xxx - * unique registers. - */ - sleep_uart0_inten = au_readl(UART0_ADDR + UART_IER); - sleep_uart0_fifoctl = au_readl(UART0_ADDR + UART_FCR); - sleep_uart0_linectl = au_readl(UART0_ADDR + UART_LCR); - sleep_uart0_clkdiv = au_readl(UART0_ADDR + UART_CLK); - sleep_uart0_enable = au_readl(UART0_ADDR + UART_MOD_CNTRL); - au_sync(); - #ifndef CONFIG_SOC_AU1200 /* Shutdown USB host/device. */ sleep_usb[0] = au_readl(USB_HOST_CONFIG); @@ -175,20 +154,6 @@ static void restore_core_regs(void) au_writel(sleep_static_memctlr[3][0], MEM_STCFG3); au_writel(sleep_static_memctlr[3][1], MEM_STTIME3); au_writel(sleep_static_memctlr[3][2], MEM_STADDR3); - - /* - * Enable the UART if it was enabled before sleep. - * I guess I should define module control bits........ - */ - if (sleep_uart0_enable & 0x02) { - au_writel(0, UART0_ADDR + UART_MOD_CNTRL); au_sync(); - au_writel(1, UART0_ADDR + UART_MOD_CNTRL); au_sync(); - au_writel(3, UART0_ADDR + UART_MOD_CNTRL); au_sync(); - au_writel(sleep_uart0_inten, UART0_ADDR + UART_IER); au_sync(); - au_writel(sleep_uart0_fifoctl, UART0_ADDR + UART_FCR); au_sync(); - au_writel(sleep_uart0_linectl, UART0_ADDR + UART_LCR); au_sync(); - au_writel(sleep_uart0_clkdiv, UART0_ADDR + UART_CLK); au_sync(); - } } void au_sleep(void) |