summaryrefslogtreecommitdiffstats
path: root/arch/mips/alchemy
diff options
context:
space:
mode:
Diffstat (limited to 'arch/mips/alchemy')
-rw-r--r--arch/mips/alchemy/Kconfig28
-rw-r--r--arch/mips/alchemy/common/Makefile7
-rw-r--r--arch/mips/alchemy/common/clocks.c7
-rw-r--r--arch/mips/alchemy/common/dbdma.c187
-rw-r--r--arch/mips/alchemy/common/dma.c36
-rw-r--r--arch/mips/alchemy/common/gpiolib-au1000.c10
-rw-r--r--arch/mips/alchemy/common/irq.c436
-rw-r--r--arch/mips/alchemy/common/platform.c153
-rw-r--r--arch/mips/alchemy/common/prom.c28
-rw-r--r--arch/mips/alchemy/common/puts.c68
-rw-r--r--arch/mips/alchemy/common/reset.c188
-rw-r--r--arch/mips/alchemy/common/setup.c40
-rw-r--r--arch/mips/alchemy/common/time.c35
-rw-r--r--arch/mips/alchemy/devboards/Makefile6
-rw-r--r--arch/mips/alchemy/devboards/bcsr.c148
-rw-r--r--arch/mips/alchemy/devboards/db1200/Makefile1
-rw-r--r--arch/mips/alchemy/devboards/db1200/platform.c561
-rw-r--r--arch/mips/alchemy/devboards/db1200/setup.c118
-rw-r--r--arch/mips/alchemy/devboards/db1x00/Makefile2
-rw-r--r--arch/mips/alchemy/devboards/db1x00/board_setup.c204
-rw-r--r--arch/mips/alchemy/devboards/db1x00/irqmap.c90
-rw-r--r--arch/mips/alchemy/devboards/db1x00/platform.c118
-rw-r--r--arch/mips/alchemy/devboards/pb1000/board_setup.c34
-rw-r--r--arch/mips/alchemy/devboards/pb1100/Makefile2
-rw-r--r--arch/mips/alchemy/devboards/pb1100/board_setup.c55
-rw-r--r--arch/mips/alchemy/devboards/pb1100/platform.c50
-rw-r--r--arch/mips/alchemy/devboards/pb1200/Makefile2
-rw-r--r--arch/mips/alchemy/devboards/pb1200/board_setup.c96
-rw-r--r--arch/mips/alchemy/devboards/pb1200/irqmap.c134
-rw-r--r--arch/mips/alchemy/devboards/pb1200/platform.c63
-rw-r--r--arch/mips/alchemy/devboards/pb1500/Makefile2
-rw-r--r--arch/mips/alchemy/devboards/pb1500/board_setup.c54
-rw-r--r--arch/mips/alchemy/devboards/pb1500/platform.c49
-rw-r--r--arch/mips/alchemy/devboards/pb1550/Makefile2
-rw-r--r--arch/mips/alchemy/devboards/pb1550/board_setup.c49
-rw-r--r--arch/mips/alchemy/devboards/pb1550/platform.c69
-rw-r--r--arch/mips/alchemy/devboards/platform.c222
-rw-r--r--arch/mips/alchemy/devboards/platform.h21
-rw-r--r--arch/mips/alchemy/devboards/pm.c32
-rw-r--r--arch/mips/alchemy/devboards/prom.c5
-rw-r--r--arch/mips/alchemy/mtx-1/Makefile2
-rw-r--r--arch/mips/alchemy/mtx-1/board_setup.c49
-rw-r--r--arch/mips/alchemy/mtx-1/init.c6
-rw-r--r--arch/mips/alchemy/mtx-1/irqmap.c56
-rw-r--r--arch/mips/alchemy/xxs1500/Makefile4
-rw-r--r--arch/mips/alchemy/xxs1500/board_setup.c60
-rw-r--r--arch/mips/alchemy/xxs1500/init.c6
-rw-r--r--arch/mips/alchemy/xxs1500/irqmap.c52
-rw-r--r--arch/mips/alchemy/xxs1500/platform.c63
49 files changed, 2428 insertions, 1282 deletions
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 00b498e97c8..df3b1a7eb15 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -1,5 +1,5 @@
-# au1000-style gpio
-config ALCHEMY_GPIO_AU1000
+# au1000-style gpio and interrupt controllers
+config ALCHEMY_GPIOINT_AU1000
bool
# select this in your board config if you don't want to use the gpio
@@ -20,12 +20,14 @@ config MIPS_MTX1
select HW_HAS_PCI
select SOC_AU1500
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_BOSPORUS
bool "Alchemy Bosporus board"
select SOC_AU1500
select DMA_NONCOHERENT
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_DB1000
bool "Alchemy DB1000 board"
@@ -33,12 +35,14 @@ config MIPS_DB1000
select DMA_NONCOHERENT
select HW_HAS_PCI
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_DB1100
bool "Alchemy DB1100 board"
select SOC_AU1100
select DMA_NONCOHERENT
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_DB1200
bool "Alchemy DB1200 board"
@@ -46,6 +50,7 @@ config MIPS_DB1200
select DMA_COHERENT
select MIPS_DISABLE_OBSOLETE_IDE
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_DB1500
bool "Alchemy DB1500 board"
@@ -55,6 +60,7 @@ config MIPS_DB1500
select MIPS_DISABLE_OBSOLETE_IDE
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_DB1550
bool "Alchemy DB1550 board"
@@ -63,12 +69,14 @@ config MIPS_DB1550
select DMA_NONCOHERENT
select MIPS_DISABLE_OBSOLETE_IDE
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_MIRAGE
bool "Alchemy Mirage board"
select DMA_NONCOHERENT
select SOC_AU1500
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_PB1000
bool "Alchemy PB1000 board"
@@ -77,6 +85,7 @@ config MIPS_PB1000
select HW_HAS_PCI
select SWAP_IO_SPACE
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_PB1100
bool "Alchemy PB1100 board"
@@ -85,6 +94,7 @@ config MIPS_PB1100
select HW_HAS_PCI
select SWAP_IO_SPACE
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_PB1200
bool "Alchemy PB1200 board"
@@ -92,6 +102,7 @@ config MIPS_PB1200
select DMA_NONCOHERENT
select MIPS_DISABLE_OBSOLETE_IDE
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_PB1500
bool "Alchemy PB1500 board"
@@ -99,6 +110,7 @@ config MIPS_PB1500
select DMA_NONCOHERENT
select HW_HAS_PCI
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_PB1550
bool "Alchemy PB1550 board"
@@ -107,39 +119,41 @@ config MIPS_PB1550
select HW_HAS_PCI
select MIPS_DISABLE_OBSOLETE_IDE
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
config MIPS_XXS1500
bool "MyCable XXS1500 board"
select DMA_NONCOHERENT
select SOC_AU1500
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_HAS_EARLY_PRINTK
endchoice
config SOC_AU1000
bool
select SOC_AU1X00
- select ALCHEMY_GPIO_AU1000
+ select ALCHEMY_GPIOINT_AU1000
config SOC_AU1100
bool
select SOC_AU1X00
- select ALCHEMY_GPIO_AU1000
+ select ALCHEMY_GPIOINT_AU1000
config SOC_AU1500
bool
select SOC_AU1X00
- select ALCHEMY_GPIO_AU1000
+ select ALCHEMY_GPIOINT_AU1000
config SOC_AU1550
bool
select SOC_AU1X00
- select ALCHEMY_GPIO_AU1000
+ select ALCHEMY_GPIOINT_AU1000
config SOC_AU1200
bool
select SOC_AU1X00
- select ALCHEMY_GPIO_AU1000
+ select ALCHEMY_GPIOINT_AU1000
config SOC_AU1X00
bool
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile
index b67fb512529..06c0e65a54b 100644
--- a/arch/mips/alchemy/common/Makefile
+++ b/arch/mips/alchemy/common/Makefile
@@ -5,14 +5,15 @@
# Makefile for the Alchemy Au1xx0 CPUs, generic files.
#
-obj-y += prom.o irq.o puts.o time.o reset.o \
- clocks.o platform.o power.o setup.o \
+obj-y += prom.o time.o clocks.o platform.o power.o setup.o \
sleeper.o dma.o dbdma.o
+obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += irq.o
+
# optional gpiolib support
ifeq ($(CONFIG_ALCHEMY_GPIO_INDIRECT),)
ifeq ($(CONFIG_GPIOLIB),y)
- obj-$(CONFIG_ALCHEMY_GPIO_AU1000) += gpiolib-au1000.o
+ obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += gpiolib-au1000.o
endif
endif
diff --git a/arch/mips/alchemy/common/clocks.c b/arch/mips/alchemy/common/clocks.c
index d8991854530..460c6285c1b 100644
--- a/arch/mips/alchemy/common/clocks.c
+++ b/arch/mips/alchemy/common/clocks.c
@@ -40,8 +40,6 @@
static unsigned int au1x00_clock; /* Hz */
static unsigned long uart_baud_base;
-static DEFINE_SPINLOCK(time_lock);
-
/*
* Set the au1000_clock
*/
@@ -84,9 +82,6 @@ void set_au1x00_uart_baud_base(unsigned long new_baud_base)
unsigned long au1xxx_calc_clock(void)
{
unsigned long cpu_speed;
- unsigned long flags;
-
- spin_lock_irqsave(&time_lock, flags);
/*
* On early Au1000, sys_cpupll was write-only. Since these
@@ -108,8 +103,6 @@ unsigned long au1xxx_calc_clock(void)
set_au1x00_uart_baud_base(cpu_speed / (2 * ((int)(au_readl(SYS_POWERCTRL)
& 0x03) + 2) * 16));
- spin_unlock_irqrestore(&time_lock, flags);
-
set_au1x00_speed(cpu_speed);
return cpu_speed;
diff --git a/arch/mips/alchemy/common/dbdma.c b/arch/mips/alchemy/common/dbdma.c
index f9201ca2295..99ae84ce5af 100644
--- a/arch/mips/alchemy/common/dbdma.c
+++ b/arch/mips/alchemy/common/dbdma.c
@@ -30,6 +30,7 @@
*
*/
+#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
@@ -58,7 +59,6 @@ static DEFINE_SPINLOCK(au1xxx_dbdma_spin_lock);
static dbdma_global_t *dbdma_gptr = (dbdma_global_t *)DDMA_GLOBAL_BASE;
static int dbdma_initialized;
-static void au1xxx_dbdma_init(void);
static dbdev_tab_t dbdev_tab[] = {
#ifdef CONFIG_SOC_AU1550
@@ -237,7 +237,7 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
void (*callback)(int, void *), void *callparam)
{
unsigned long flags;
- u32 used, chan, rv;
+ u32 used, chan;
u32 dcp;
int i;
dbdev_tab_t *stp, *dtp;
@@ -250,8 +250,7 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
* which can't be done successfully during board set up.
*/
if (!dbdma_initialized)
- au1xxx_dbdma_init();
- dbdma_initialized = 1;
+ return 0;
stp = find_dbdev_id(srcid);
if (stp == NULL)
@@ -261,7 +260,6 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
return 0;
used = 0;
- rv = 0;
/* Check to see if we can get both channels. */
spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
@@ -282,63 +280,65 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
used++;
spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
- if (!used) {
- /* Let's see if we can allocate a channel for it. */
- ctp = NULL;
- chan = 0;
- spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
- for (i = 0; i < NUM_DBDMA_CHANS; i++)
- if (chan_tab_ptr[i] == NULL) {
- /*
- * If kmalloc fails, it is caught below same
- * as a channel not available.
- */
- ctp = kmalloc(sizeof(chan_tab_t), GFP_ATOMIC);
- chan_tab_ptr[i] = ctp;
- break;
- }
- spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
-
- if (ctp != NULL) {
- memset(ctp, 0, sizeof(chan_tab_t));
- ctp->chan_index = chan = i;
- dcp = DDMA_CHANNEL_BASE;
- dcp += (0x0100 * chan);
- ctp->chan_ptr = (au1x_dma_chan_t *)dcp;
- cp = (au1x_dma_chan_t *)dcp;
- ctp->chan_src = stp;
- ctp->chan_dest = dtp;
- ctp->chan_callback = callback;
- ctp->chan_callparam = callparam;
-
- /* Initialize channel configuration. */
- i = 0;
- if (stp->dev_intlevel)
- i |= DDMA_CFG_SED;
- if (stp->dev_intpolarity)
- i |= DDMA_CFG_SP;
- if (dtp->dev_intlevel)
- i |= DDMA_CFG_DED;
- if (dtp->dev_intpolarity)
- i |= DDMA_CFG_DP;
- if ((stp->dev_flags & DEV_FLAGS_SYNC) ||
- (dtp->dev_flags & DEV_FLAGS_SYNC))
- i |= DDMA_CFG_SYNC;
- cp->ddma_cfg = i;
- au_sync();
+ if (used)
+ return 0;
- /* Return a non-zero value that can be used to
- * find the channel information in subsequent
- * operations.
+ /* Let's see if we can allocate a channel for it. */
+ ctp = NULL;
+ chan = 0;
+ spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
+ for (i = 0; i < NUM_DBDMA_CHANS; i++)
+ if (chan_tab_ptr[i] == NULL) {
+ /*
+ * If kmalloc fails, it is caught below same
+ * as a channel not available.
*/
- rv = (u32)(&chan_tab_ptr[chan]);
- } else {
- /* Release devices */
- stp->dev_flags &= ~DEV_FLAGS_INUSE;
- dtp->dev_flags &= ~DEV_FLAGS_INUSE;
+ ctp = kmalloc(sizeof(chan_tab_t), GFP_ATOMIC);
+ chan_tab_ptr[i] = ctp;
+ break;
}
+ spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
+
+ if (ctp != NULL) {
+ memset(ctp, 0, sizeof(chan_tab_t));
+ ctp->chan_index = chan = i;
+ dcp = DDMA_CHANNEL_BASE;
+ dcp += (0x0100 * chan);
+ ctp->chan_ptr = (au1x_dma_chan_t *)dcp;
+ cp = (au1x_dma_chan_t *)dcp;
+ ctp->chan_src = stp;
+ ctp->chan_dest = dtp;
+ ctp->chan_callback = callback;
+ ctp->chan_callparam = callparam;
+
+ /* Initialize channel configuration. */
+ i = 0;
+ if (stp->dev_intlevel)
+ i |= DDMA_CFG_SED;
+ if (stp->dev_intpolarity)
+ i |= DDMA_CFG_SP;
+ if (dtp->dev_intlevel)
+ i |= DDMA_CFG_DED;
+ if (dtp->dev_intpolarity)
+ i |= DDMA_CFG_DP;
+ if ((stp->dev_flags & DEV_FLAGS_SYNC) ||
+ (dtp->dev_flags & DEV_FLAGS_SYNC))
+ i |= DDMA_CFG_SYNC;
+ cp->ddma_cfg = i;
+ au_sync();
+
+ /*
+ * Return a non-zero value that can be used to find the channel
+ * information in subsequent operations.
+ */
+ return (u32)(&chan_tab_ptr[chan]);
}
- return rv;
+
+ /* Release devices */
+ stp->dev_flags &= ~DEV_FLAGS_INUSE;
+ dtp->dev_flags &= ~DEV_FLAGS_INUSE;
+
+ return 0;
}
EXPORT_SYMBOL(au1xxx_dbdma_chan_alloc);
@@ -572,7 +572,7 @@ EXPORT_SYMBOL(au1xxx_dbdma_ring_alloc);
* This updates the source pointer and byte count. Normally used
* for memory to fifo transfers.
*/
-u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags)
+u32 au1xxx_dbdma_put_source(u32 chanid, dma_addr_t buf, int nbytes, u32 flags)
{
chan_tab_t *ctp;
au1x_ddma_desc_t *dp;
@@ -598,7 +598,7 @@ u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags)
return 0;
/* Load up buffer address and byte count. */
- dp->dscr_source0 = virt_to_phys(buf);
+ dp->dscr_source0 = buf & ~0UL;
dp->dscr_cmd1 = nbytes;
/* Check flags */
if (flags & DDMA_FLAGS_IE)
@@ -625,14 +625,13 @@ u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags)
/* Return something non-zero. */
return nbytes;
}
-EXPORT_SYMBOL(_au1xxx_dbdma_put_source);
+EXPORT_SYMBOL(au1xxx_dbdma_put_source);
/* Put a destination buffer into the DMA ring.
* This updates the destination pointer and byte count. Normally used
* to place an empty buffer into the ring for fifo to memory transfers.
*/
-u32
-_au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags)
+u32 au1xxx_dbdma_put_dest(u32 chanid, dma_addr_t buf, int nbytes, u32 flags)
{
chan_tab_t *ctp;
au1x_ddma_desc_t *dp;
@@ -662,7 +661,7 @@ _au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags)
if (flags & DDMA_FLAGS_NOIE)
dp->dscr_cmd0 &= ~DSCR_CMD0_IE;
- dp->dscr_dest0 = virt_to_phys(buf);
+ dp->dscr_dest0 = buf & ~0UL;
dp->dscr_cmd1 = nbytes;
#if 0
printk(KERN_DEBUG "cmd0:%x cmd1:%x source0:%x source1:%x dest0:%x dest1:%x\n",
@@ -688,7 +687,7 @@ _au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags)
/* Return something non-zero. */
return nbytes;
}
-EXPORT_SYMBOL(_au1xxx_dbdma_put_dest);
+EXPORT_SYMBOL(au1xxx_dbdma_put_dest);
/*
* Get a destination buffer into the DMA ring.
@@ -871,28 +870,6 @@ static irqreturn_t dbdma_interrupt(int irq, void *dev_id)
return IRQ_RETVAL(1);
}
-static void au1xxx_dbdma_init(void)
-{
- int irq_nr;
-
- dbdma_gptr->ddma_config = 0;
- dbdma_gptr->ddma_throttle = 0;
- dbdma_gptr->ddma_inten = 0xffff;
- au_sync();
-
-#if defined(CONFIG_SOC_AU1550)
- irq_nr = AU1550_DDMA_INT;
-#elif defined(CONFIG_SOC_AU1200)
- irq_nr = AU1200_DDMA_INT;
-#else
- #error Unknown Au1x00 SOC
-#endif
-
- if (request_irq(irq_nr, dbdma_interrupt, IRQF_DISABLED,
- "Au1xxx dbdma", (void *)dbdma_gptr))
- printk(KERN_ERR "Can't get 1550 dbdma irq");
-}
-
void au1xxx_dbdma_dump(u32 chanid)
{
chan_tab_t *ctp;
@@ -906,7 +883,7 @@ void au1xxx_dbdma_dump(u32 chanid)
dtp = ctp->chan_dest;
cp = ctp->chan_ptr;
- printk(KERN_DEBUG "Chan %x, stp %x (dev %d) dtp %x (dev %d) \n",
+ printk(KERN_DEBUG "Chan %x, stp %x (dev %d) dtp %x (dev %d)\n",
(u32)ctp, (u32)stp, stp - dbdev_tab, (u32)dtp,
dtp - dbdev_tab);
printk(KERN_DEBUG "desc base %x, get %x, put %x, cur %x\n",
@@ -1041,4 +1018,38 @@ void au1xxx_dbdma_resume(void)
}
}
#endif /* CONFIG_PM */
+
+static int __init au1xxx_dbdma_init(void)
+{
+ int irq_nr, ret;
+
+ dbdma_gptr->ddma_config = 0;
+ dbdma_gptr->ddma_throttle = 0;
+ dbdma_gptr->ddma_inten = 0xffff;
+ au_sync();
+
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1550:
+ irq_nr = AU1550_DDMA_INT;
+ break;
+ case ALCHEMY_CPU_AU1200:
+ irq_nr = AU1200_DDMA_INT;
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ ret = request_irq(irq_nr, dbdma_interrupt, IRQF_DISABLED,
+ "Au1xxx dbdma", (void *)dbdma_gptr);
+ if (ret)
+ printk(KERN_ERR "Cannot grab DBDMA interrupt!\n");
+ else {
+ dbdma_initialized = 1;
+ printk(KERN_INFO "Alchemy DBDMA initialized\n");
+ }
+
+ return ret;
+}
+subsys_initcall(au1xxx_dbdma_init);
+
#endif /* defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200) */
diff --git a/arch/mips/alchemy/common/dma.c b/arch/mips/alchemy/common/dma.c
index d6fbda232e6..d5278877891 100644
--- a/arch/mips/alchemy/common/dma.c
+++ b/arch/mips/alchemy/common/dma.c
@@ -29,6 +29,8 @@
* 675 Mass Ave, Cambridge, MA 02139, USA.
*
*/
+
+#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/errno.h>
@@ -188,17 +190,14 @@ int request_au1000_dma(int dev_id, const char *dev_str,
dev = &dma_dev_table[dev_id];
if (irqhandler) {
- chan->irq = AU1000_DMA_INT_BASE + i;
chan->irq_dev = irq_dev_id;
ret = request_irq(chan->irq, irqhandler, irqflags, dev_str,
chan->irq_dev);
if (ret) {
- chan->irq = 0;
chan->irq_dev = NULL;
return ret;
}
} else {
- chan->irq = 0;
chan->irq_dev = NULL;
}
@@ -226,13 +225,40 @@ void free_au1000_dma(unsigned int dmanr)
}
disable_dma(dmanr);
- if (chan->irq)
+ if (chan->irq_dev)
free_irq(chan->irq, chan->irq_dev);
- chan->irq = 0;
chan->irq_dev = NULL;
chan->dev_id = -1;
}
EXPORT_SYMBOL(free_au1000_dma);
+static int __init au1000_dma_init(void)
+{
+ int base, i;
+
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1000:
+ base = AU1000_DMA_INT_BASE;
+ break;
+ case ALCHEMY_CPU_AU1500:
+ base = AU1500_DMA_INT_BASE;
+ break;
+ case ALCHEMY_CPU_AU1100:
+ base = AU1100_DMA_INT_BASE;
+ break;
+ default:
+ goto out;
+ }
+
+ for (i = 0; i < NUM_AU1000_DMA_CHANNELS; i++)
+ au1000_dma_table[i].irq = base + i;
+
+ printk(KERN_INFO "Alchemy DMA initialized\n");
+
+out:
+ return 0;
+}
+arch_initcall(au1000_dma_init);
+
#endif /* AU1000 AU1500 AU1100 */
diff --git a/arch/mips/alchemy/common/gpiolib-au1000.c b/arch/mips/alchemy/common/gpiolib-au1000.c
index 1bfa91f939f..c8e1a94d4a9 100644
--- a/arch/mips/alchemy/common/gpiolib-au1000.c
+++ b/arch/mips/alchemy/common/gpiolib-au1000.c
@@ -36,7 +36,6 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/gpio.h>
-#if !defined(CONFIG_SOC_AU1000)
static int gpio2_get(struct gpio_chip *chip, unsigned offset)
{
return alchemy_gpio2_get_value(offset + ALCHEMY_GPIO2_BASE);
@@ -63,7 +62,7 @@ static int gpio2_to_irq(struct gpio_chip *chip, unsigned offset)
{
return alchemy_gpio2_to_irq(offset + ALCHEMY_GPIO2_BASE);
}
-#endif /* !defined(CONFIG_SOC_AU1000) */
+
static int gpio1_get(struct gpio_chip *chip, unsigned offset)
{
@@ -104,7 +103,6 @@ struct gpio_chip alchemy_gpio_chip[] = {
.base = ALCHEMY_GPIO1_BASE,
.ngpio = ALCHEMY_GPIO1_NUM,
},
-#if !defined(CONFIG_SOC_AU1000)
[1] = {
.label = "alchemy-gpio2",
.direction_input = gpio2_direction_input,
@@ -115,15 +113,13 @@ struct gpio_chip alchemy_gpio_chip[] = {
.base = ALCHEMY_GPIO2_BASE,
.ngpio = ALCHEMY_GPIO2_NUM,
},
-#endif
};
static int __init alchemy_gpiolib_init(void)
{
gpiochip_add(&alchemy_gpio_chip[0]);
-#if !defined(CONFIG_SOC_AU1000)
- gpiochip_add(&alchemy_gpio_chip[1]);
-#endif
+ if (alchemy_get_cputype() != ALCHEMY_CPU_AU1000)
+ gpiochip_add(&alchemy_gpio_chip[1]);
return 0;
}
diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
index d670928afcf..b2821ace4d0 100644
--- a/arch/mips/alchemy/common/irq.c
+++ b/arch/mips/alchemy/common/irq.c
@@ -39,168 +39,180 @@
static int au1x_ic_settype(unsigned int irq, unsigned int flow_type);
+/* NOTE on interrupt priorities: The original writers of this code said:
+ *
+ * Because of the tight timing of SETUP token to reply transactions,
+ * the USB devices-side packet complete interrupt (USB_DEV_REQ_INT)
+ * needs the highest priority.
+ */
+
/* per-processor fixed function irqs */
-struct au1xxx_irqmap au1xxx_ic0_map[] __initdata = {
-
-#if defined(CONFIG_SOC_AU1000)
- { AU1000_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_UART2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
- { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
-
-#elif defined(CONFIG_SOC_AU1500)
-
- { AU1500_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1000_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1500_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1000_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
- { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1500_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1500_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
-
-#elif defined(CONFIG_SOC_AU1100)
-
- { AU1100_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1100_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1100_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1100_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
- { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+struct au1xxx_irqmap {
+ int im_irq;
+ int im_type;
+ int im_request; /* set 1 to get higher priority */
+};
+
+struct au1xxx_irqmap au1000_irqmap[] __initdata = {
+ { AU1000_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_UART2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1000_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 1 },
{ AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1100_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1100_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
-
-#elif defined(CONFIG_SOC_AU1550)
-
- { AU1550_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1550_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1550_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_CRYPTO_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1550_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1550_PCI_RST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1550_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_PSC2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_PSC3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
- { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1550_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1550_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { -1, },
+};
+
+struct au1xxx_irqmap au1500_irqmap[] __initdata = {
+ { AU1500_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1500_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1500_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1500_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1500_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1500_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 1 },
+ { AU1500_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1500_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { -1, },
+};
+
+struct au1xxx_irqmap au1100_irqmap[] __initdata = {
+ { AU1100_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1100_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 1 },
+ { AU1100_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1100_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { -1, },
+};
+
+struct au1xxx_irqmap au1550_irqmap[] __initdata = {
+ { AU1550_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_CRYPTO_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_PCI_RST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1550_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 1 },
{ AU1550_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1550_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
- { AU1550_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1550_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-
-#elif defined(CONFIG_SOC_AU1200)
-
- { AU1200_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_SWT_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1200_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_MAE_BE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_MAE_FE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_AES_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_CAMERA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
- { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1200_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
- { AU1200_USB_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
- { AU1200_MAE_BOTH_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-
-#else
-#error "Error: Unknown Alchemy SOC"
-#endif
+ { AU1550_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { -1, },
+};
+
+struct au1xxx_irqmap au1200_irqmap[] __initdata = {
+ { AU1200_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_SWT_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_MAE_BE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_MAE_FE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_AES_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_CAMERA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1200_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_USB_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_MAE_BOTH_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { -1, },
};
@@ -306,7 +318,7 @@ static void au1x_ic1_unmask(unsigned int irq_nr)
* nowhere in the current kernel sources is it disabled. --mlau
*/
#if defined(CONFIG_MIPS_PB1000)
- if (irq_nr == AU1000_GPIO_15)
+ if (irq_nr == AU1000_GPIO15_INT)
au_writel(0x4000, PB1000_MDR); /* enable int */
#endif
au_sync();
@@ -378,11 +390,13 @@ static void au1x_ic1_maskack(unsigned int irq_nr)
static int au1x_ic1_setwake(unsigned int irq, unsigned int on)
{
- unsigned int bit = irq - AU1000_INTC1_INT_BASE;
+ int bit = irq - AU1000_INTC1_INT_BASE;
unsigned long wakemsk, flags;
- /* only GPIO 0-7 can act as wakeup source: */
- if ((irq < AU1000_GPIO_0) || (irq > AU1000_GPIO_7))
+ /* only GPIO 0-7 can act as wakeup source. Fortunately these
+ * are wired up identically on all supported variants.
+ */
+ if ((bit < 0) || (bit > 7))
return -EINVAL;
local_irq_save(flags);
@@ -504,11 +518,11 @@ static int au1x_ic_settype(unsigned int irq, unsigned int flow_type)
asmlinkage void plat_irq_dispatch(void)
{
unsigned int pending = read_c0_status() & read_c0_cause();
- unsigned long s, off, bit;
+ unsigned long s, off;
if (pending & CAUSEF_IP7) {
- do_IRQ(MIPS_CPU_IRQ_BASE + 7);
- return;
+ off = MIPS_CPU_IRQ_BASE + 7;
+ goto handle;
} else if (pending & CAUSEF_IP2) {
s = IC0_REQ0INT;
off = AU1000_INTC0_INT_BASE;
@@ -524,58 +538,20 @@ asmlinkage void plat_irq_dispatch(void)
} else
goto spurious;
- bit = 0;
s = au_readl(s);
if (unlikely(!s)) {
spurious:
spurious_interrupt();
return;
}
-#ifdef AU1000_USB_DEV_REQ_INT
- /*
- * Because of the tight timing of SETUP token to reply
- * transactions, the USB devices-side packet complete
- * interrupt needs the highest priority.
- */
- bit = 1 << (AU1000_USB_DEV_REQ_INT - AU1000_INTC0_INT_BASE);
- if ((pending & CAUSEF_IP2) && (s & bit)) {
- do_IRQ(AU1000_USB_DEV_REQ_INT);
- return;
- }
-#endif
- do_IRQ(__ffs(s) + off);
+ off += __ffs(s);
+handle:
+ do_IRQ(off);
}
-/* setup edge/level and assign request 0/1 */
-void __init au1xxx_setup_irqmap(struct au1xxx_irqmap *map, int count)
+static void __init au1000_init_irq(struct au1xxx_irqmap *map)
{
unsigned int bit, irq_nr;
-
- while (count--) {
- irq_nr = map[count].im_irq;
-
- if (((irq_nr < AU1000_INTC0_INT_BASE) ||
- (irq_nr >= AU1000_INTC0_INT_BASE + 32)) &&
- ((irq_nr < AU1000_INTC1_INT_BASE) ||
- (irq_nr >= AU1000_INTC1_INT_BASE + 32)))
- continue;
-
- if (irq_nr >= AU1000_INTC1_INT_BASE) {
- bit = irq_nr - AU1000_INTC1_INT_BASE;
- if (map[count].im_request)
- au_writel(1 << bit, IC1_ASSIGNCLR);
- } else {
- bit = irq_nr - AU1000_INTC0_INT_BASE;
- if (map[count].im_request)
- au_writel(1 << bit, IC0_ASSIGNCLR);
- }
-
- au1x_ic_settype(irq_nr, map[count].im_type);
- }
-}
-
-void __init arch_init_irq(void)
-{
int i;
/*
@@ -585,7 +561,7 @@ void __init arch_init_irq(void)
au_writel(0xffffffff, IC0_CFG1CLR);
au_writel(0xffffffff, IC0_CFG2CLR);
au_writel(0xffffffff, IC0_MASKCLR);
- au_writel(0xffffffff, IC0_ASSIGNSET);
+ au_writel(0xffffffff, IC0_ASSIGNCLR);
au_writel(0xffffffff, IC0_WAKECLR);
au_writel(0xffffffff, IC0_SRCSET);
au_writel(0xffffffff, IC0_FALLINGCLR);
@@ -596,7 +572,7 @@ void __init arch_init_irq(void)
au_writel(0xffffffff, IC1_CFG1CLR);
au_writel(0xffffffff, IC1_CFG2CLR);
au_writel(0xffffffff, IC1_MASKCLR);
- au_writel(0xffffffff, IC1_ASSIGNSET);
+ au_writel(0xffffffff, IC1_ASSIGNCLR);
au_writel(0xffffffff, IC1_WAKECLR);
au_writel(0xffffffff, IC1_SRCSET);
au_writel(0xffffffff, IC1_FALLINGCLR);
@@ -619,11 +595,43 @@ void __init arch_init_irq(void)
/*
* Initialize IC0, which is fixed per processor.
*/
- au1xxx_setup_irqmap(au1xxx_ic0_map, ARRAY_SIZE(au1xxx_ic0_map));
+ while (map->im_irq != -1) {
+ irq_nr = map->im_irq;
- /* Boards can register additional (GPIO-based) IRQs.
- */
- board_init_irq();
+ if (irq_nr >= AU1000_INTC1_INT_BASE) {
+ bit = irq_nr - AU1000_INTC1_INT_BASE;
+ if (map->im_request)
+ au_writel(1 << bit, IC1_ASSIGNSET);
+ } else {
+ bit = irq_nr - AU1000_INTC0_INT_BASE;
+ if (map->im_request)
+ au_writel(1 << bit, IC0_ASSIGNSET);
+ }
+
+ au1x_ic_settype(irq_nr, map->im_type);
+ ++map;
+ }
set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3);
}
+
+void __init arch_init_irq(void)
+{
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1000:
+ au1000_init_irq(au1000_irqmap);
+ break;
+ case ALCHEMY_CPU_AU1500:
+ au1000_init_irq(au1500_irqmap);
+ break;
+ case ALCHEMY_CPU_AU1100:
+ au1000_init_irq(au1100_irqmap);
+ break;
+ case ALCHEMY_CPU_AU1550:
+ au1000_init_irq(au1550_irqmap);
+ break;
+ case ALCHEMY_CPU_AU1200:
+ au1000_init_irq(au1200_irqmap);
+ break;
+ }
+}
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 117f99f7064..2580e77624d 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -19,39 +19,40 @@
#include <asm/mach-au1x00/au1xxx.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#include <asm/mach-au1x00/au1100_mmc.h>
-
-#define PORT(_base, _irq) \
- { \
- .iobase = _base, \
- .membase = (void __iomem *)_base,\
- .mapbase = CPHYSADDR(_base), \
- .irq = _irq, \
- .regshift = 2, \
- .iotype = UPIO_AU, \
- .flags = UPF_SKIP_TEST \
+#include <asm/mach-au1x00/au1xxx_eth.h>
+
+#define PORT(_base, _irq) \
+ { \
+ .mapbase = _base, \
+ .irq = _irq, \
+ .regshift = 2, \
+ .iotype = UPIO_AU, \
+ .flags = UPF_SKIP_TEST | UPF_IOREMAP | \
+ UPF_FIXED_TYPE, \
+ .type = PORT_16550A, \
}
static struct plat_serial8250_port au1x00_uart_data[] = {
#if defined(CONFIG_SERIAL_8250_AU1X00)
#if defined(CONFIG_SOC_AU1000)
- PORT(UART0_ADDR, AU1000_UART0_INT),
- PORT(UART1_ADDR, AU1000_UART1_INT),
- PORT(UART2_ADDR, AU1000_UART2_INT),
- PORT(UART3_ADDR, AU1000_UART3_INT),
+ PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
+ PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
+ PORT(UART2_PHYS_ADDR, AU1000_UART2_INT),
+ PORT(UART3_PHYS_ADDR, AU1000_UART3_INT),
#elif defined(CONFIG_SOC_AU1500)
- PORT(UART0_ADDR, AU1500_UART0_INT),
- PORT(UART3_ADDR, AU1500_UART3_INT),
+ PORT(UART0_PHYS_ADDR, AU1500_UART0_INT),
+ PORT(UART3_PHYS_ADDR, AU1500_UART3_INT),
#elif defined(CONFIG_SOC_AU1100)
- PORT(UART0_ADDR, AU1100_UART0_INT),
- PORT(UART1_ADDR, AU1100_UART1_INT),
- PORT(UART3_ADDR, AU1100_UART3_INT),
+ PORT(UART0_PHYS_ADDR, AU1100_UART0_INT),
+ PORT(UART1_PHYS_ADDR, AU1100_UART1_INT),
+ PORT(UART3_PHYS_ADDR, AU1100_UART3_INT),
#elif defined(CONFIG_SOC_AU1550)
- PORT(UART0_ADDR, AU1550_UART0_INT),
- PORT(UART1_ADDR, AU1550_UART1_INT),
- PORT(UART3_ADDR, AU1550_UART3_INT),
+ PORT(UART0_PHYS_ADDR, AU1550_UART0_INT),
+ PORT(UART1_PHYS_ADDR, AU1550_UART1_INT),
+ PORT(UART3_PHYS_ADDR, AU1550_UART3_INT),
#elif defined(CONFIG_SOC_AU1200)
- PORT(UART0_ADDR, AU1200_UART0_INT),
- PORT(UART1_ADDR, AU1200_UART1_INT),
+ PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
+ PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
#endif
#endif /* CONFIG_SERIAL_8250_AU1X00 */
{ },
@@ -73,8 +74,8 @@ static struct resource au1xxx_usb_ohci_resources[] = {
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AU1000_USB_HOST_INT,
- .end = AU1000_USB_HOST_INT,
+ .start = FOR_PLATFORM_C_USB_HOST_INT,
+ .end = FOR_PLATFORM_C_USB_HOST_INT,
.flags = IORESOURCE_IRQ,
},
};
@@ -132,8 +133,8 @@ static struct resource au1xxx_usb_ehci_resources[] = {
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = AU1000_USB_HOST_INT,
- .end = AU1000_USB_HOST_INT,
+ .start = AU1200_USB_INT,
+ .end = AU1200_USB_INT,
.flags = IORESOURCE_IRQ,
},
};
@@ -308,11 +309,6 @@ static struct platform_device au1200_mmc1_device = {
#endif /* #ifndef CONFIG_MIPS_DB1200 */
#endif /* #ifdef CONFIG_SOC_AU1200 */
-static struct platform_device au1x00_pcmcia_device = {
- .name = "au1x00-pcmcia",
- .id = 0,
-};
-
/* All Alchemy demoboards with I2C have this #define in their headers */
#ifdef SMBUS_PSC_BASE
static struct resource pbdb_smbus_resources[] = {
@@ -331,10 +327,92 @@ static struct platform_device pbdb_smbus_device = {
};
#endif
+/* Macro to help defining the Ethernet MAC resources */
+#define MAC_RES(_base, _enable, _irq) \
+ { \
+ .start = CPHYSADDR(_base), \
+ .end = CPHYSADDR(_base + 0xffff), \
+ .flags = IORESOURCE_MEM, \
+ }, \
+ { \
+ .start = CPHYSADDR(_enable), \
+ .end = CPHYSADDR(_enable + 0x3), \
+ .flags = IORESOURCE_MEM, \
+ }, \
+ { \
+ .start = _irq, \
+ .end = _irq, \
+ .flags = IORESOURCE_IRQ \
+ }
+
+static struct resource au1xxx_eth0_resources[] = {
+#if defined(CONFIG_SOC_AU1000)
+ MAC_RES(AU1000_ETH0_BASE, AU1000_MAC0_ENABLE, AU1000_MAC0_DMA_INT),
+#elif defined(CONFIG_SOC_AU1100)
+ MAC_RES(AU1100_ETH0_BASE, AU1100_MAC0_ENABLE, AU1100_MAC0_DMA_INT),
+#elif defined(CONFIG_SOC_AU1550)
+ MAC_RES(AU1550_ETH0_BASE, AU1550_MAC0_ENABLE, AU1550_MAC0_DMA_INT),
+#elif defined(CONFIG_SOC_AU1500)
+ MAC_RES(AU1500_ETH0_BASE, AU1500_MAC0_ENABLE, AU1500_MAC0_DMA_INT),
+#endif
+};
+
+
+static struct au1000_eth_platform_data au1xxx_eth0_platform_data = {
+ .phy1_search_mac0 = 1,
+};
+
+static struct platform_device au1xxx_eth0_device = {
+ .name = "au1000-eth",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(au1xxx_eth0_resources),
+ .resource = au1xxx_eth0_resources,
+ .dev.platform_data = &au1xxx_eth0_platform_data,
+};
+
+#ifndef CONFIG_SOC_AU1100
+static struct resource au1xxx_eth1_resources[] = {
+#if defined(CONFIG_SOC_AU1000)
+ MAC_RES(AU1000_ETH1_BASE, AU1000_MAC1_ENABLE, AU1000_MAC1_DMA_INT),
+#elif defined(CONFIG_SOC_AU1550)
+ MAC_RES(AU1550_ETH1_BASE, AU1550_MAC1_ENABLE, AU1550_MAC1_DMA_INT),
+#elif defined(CONFIG_SOC_AU1500)
+ MAC_RES(AU1500_ETH1_BASE, AU1500_MAC1_ENABLE, AU1500_MAC1_DMA_INT),
+#endif
+};
+
+static struct au1000_eth_platform_data au1xxx_eth1_platform_data = {
+ .phy1_search_mac0 = 1,
+};
+
+static struct platform_device au1xxx_eth1_device = {
+ .name = "au1000-eth",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(au1xxx_eth1_resources),
+ .resource = au1xxx_eth1_resources,
+ .dev.platform_data = &au1xxx_eth1_platform_data,
+};
+#endif
+
+void __init au1xxx_override_eth_cfg(unsigned int port,
+ struct au1000_eth_platform_data *eth_data)
+{
+ if (!eth_data || port > 1)
+ return;
+
+ if (port == 0)
+ memcpy(&au1xxx_eth0_platform_data, eth_data,
+ sizeof(struct au1000_eth_platform_data));
+#ifndef CONFIG_SOC_AU1100
+ else
+ memcpy(&au1xxx_eth1_platform_data, eth_data,
+ sizeof(struct au1000_eth_platform_data));
+#endif
+}
+
static struct platform_device *au1xxx_platform_devices[] __initdata = {
&au1xx0_uart_device,
&au1xxx_usb_ohci_device,
- &au1x00_pcmcia_device,
#ifdef CONFIG_FB_AU1100
&au1100_lcd_device,
#endif
@@ -351,6 +429,7 @@ static struct platform_device *au1xxx_platform_devices[] __initdata = {
#ifdef SMBUS_PSC_BASE
&pbdb_smbus_device,
#endif
+ &au1xxx_eth0_device,
};
static int __init au1xxx_platform_init(void)
@@ -362,6 +441,12 @@ static int __init au1xxx_platform_init(void)
for (i = 0; au1x00_uart_data[i].flags; i++)
au1x00_uart_data[i].uartclk = uartclk;
+#ifndef CONFIG_SOC_AU1100
+ /* Register second MAC if enabled in pinfunc */
+ if (!(au_readl(SYS_PINFUNC) & (u32)SYS_PF_NI2))
+ platform_device_register(&au1xxx_eth1_device);
+#endif
+
return platform_add_devices(au1xxx_platform_devices,
ARRAY_SIZE(au1xxx_platform_devices));
}
diff --git a/arch/mips/alchemy/common/prom.c b/arch/mips/alchemy/common/prom.c
index 18b310b475c..c29511b11d4 100644
--- a/arch/mips/alchemy/common/prom.c
+++ b/arch/mips/alchemy/common/prom.c
@@ -43,29 +43,15 @@ int prom_argc;
char **prom_argv;
char **prom_envp;
-char * __init_or_module prom_getcmdline(void)
-{
- return &(arcs_cmdline[0]);
-}
-
void prom_init_cmdline(void)
{
- char *cp;
- int actr;
-
- actr = 1; /* Always ignore argv[0] */
+ int i;
- cp = &(arcs_cmdline[0]);
- while (actr < prom_argc) {
- strcpy(cp, prom_argv[actr]);
- cp += strlen(prom_argv[actr]);
- *cp++ = ' ';
- actr++;
+ for (i = 1; i < prom_argc; i++) {
+ strlcat(arcs_cmdline, prom_argv[i], COMMAND_LINE_SIZE);
+ if (i < (prom_argc - 1))
+ strlcat(arcs_cmdline, " ", COMMAND_LINE_SIZE);
}
- if (cp != &(arcs_cmdline[0])) /* get rid of trailing space */
- --cp;
- if (prom_argc > 1)
- *cp = '\0';
}
char *prom_getenv(char *envname)
@@ -121,14 +107,12 @@ static inline void str2eaddr(unsigned char *ea, unsigned char *str)
int prom_get_ethernet_addr(char *ethernet_addr)
{
char *ethaddr_str;
- char *argptr;
/* Check the environment variables first */
ethaddr_str = prom_getenv("ethaddr");
if (!ethaddr_str) {
/* Check command line */
- argptr = prom_getcmdline();
- ethaddr_str = strstr(argptr, "ethaddr=");
+ ethaddr_str = strstr(arcs_cmdline, "ethaddr=");
if (!ethaddr_str)
return -1;
diff --git a/arch/mips/alchemy/common/puts.c b/arch/mips/alchemy/common/puts.c
deleted file mode 100644
index 55bbe24d45b..00000000000
--- a/arch/mips/alchemy/common/puts.c
+++ /dev/null
@@ -1,68 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Low level UART routines to directly access Alchemy UART.
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <asm/mach-au1x00/au1000.h>
-
-#define SERIAL_BASE UART_BASE
-#define SER_CMD 0x7
-#define SER_DATA 0x1
-#define TX_BUSY 0x20
-
-#define TIMEOUT 0xffffff
-#define SLOW_DOWN
-
-static volatile unsigned long * const com1 = (unsigned long *)SERIAL_BASE;
-
-#ifdef SLOW_DOWN
-static inline void slow_down(void)
-{
- int k;
-
- for (k = 0; k < 10000; k++);
-}
-#else
-#define slow_down()
-#endif
-
-void
-prom_putchar(const unsigned char c)
-{
- unsigned char ch;
- int i = 0;
-
- do {
- ch = com1[SER_CMD];
- slow_down();
- i++;
- if (i > TIMEOUT)
- break;
- } while (0 == (ch & TX_BUSY));
-
- com1[SER_DATA] = c;
-}
diff --git a/arch/mips/alchemy/common/reset.c b/arch/mips/alchemy/common/reset.c
deleted file mode 100644
index 4791011e8f9..00000000000
--- a/arch/mips/alchemy/common/reset.c
+++ /dev/null
@@ -1,188 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Au1xx0 reset routines.
- *
- * Copyright 2001, 2006, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-
-#include <asm/cacheflush.h>
-#include <asm/mach-au1x00/au1000.h>
-
-void au1000_restart(char *command)
-{
- /* Set all integrated peripherals to disabled states */
- extern void board_reset(void);
- u32 prid = read_c0_prid();
-
- printk(KERN_NOTICE "\n** Resetting Integrated Peripherals\n");
-
- switch (prid & 0xFF000000) {
- case 0x00000000: /* Au1000 */
- au_writel(0x02, 0xb0000010); /* ac97_enable */
- au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
- asm("sync");
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb0300040); /* ir_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb0520000); /* macen0 */
- au_writel(0x00, 0xb0520004); /* macen1 */
- au_writel(0x00, 0xb1000008); /* i2s_enable */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1200100); /* uart1_enable */
- au_writel(0x00, 0xb1300100); /* uart2_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x02, 0xb1600100); /* ssi0_enable */
- au_writel(0x02, 0xb1680100); /* ssi1_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- case 0x01000000: /* Au1500 */
- au_writel(0x02, 0xb0000010); /* ac97_enable */
- au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
- asm("sync");
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb1520000); /* macen0 */
- au_writel(0x00, 0xb1520004); /* macen1 */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- case 0x02000000: /* Au1100 */
- au_writel(0x02, 0xb0000010); /* ac97_enable */
- au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
- asm("sync");
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb0300040); /* ir_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb0520000); /* macen0 */
- au_writel(0x00, 0xb1000008); /* i2s_enable */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1200100); /* uart1_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x02, 0xb1600100); /* ssi0_enable */
- au_writel(0x02, 0xb1680100); /* ssi1_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- case 0x03000000: /* Au1550 */
- au_writel(0x00, 0xb1a00004); /* psc 0 */
- au_writel(0x00, 0xb1b00004); /* psc 1 */
- au_writel(0x00, 0xb0a00004); /* psc 2 */
- au_writel(0x00, 0xb0b00004); /* psc 3 */
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb1520000); /* macen0 */
- au_writel(0x00, 0xb1520004); /* macen1 */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1200100); /* uart1_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- }
-
- set_c0_status(ST0_BEV | ST0_ERL);
- change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
- flush_cache_all();
- write_c0_wired(0);
-
- /* Give board a chance to do a hardware reset */
- board_reset();
-
- /* Jump to the beggining in case board_reset() is empty */
- __asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
-}
-
-void au1000_halt(void)
-{
-#if defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550)
- /* Power off system */
- printk(KERN_NOTICE "\n** Powering off...\n");
- au_writew(au_readw(0xAF00001C) | (3 << 14), 0xAF00001C);
- au_sync();
- while (1); /* should not get here */
-#else
- printk(KERN_NOTICE "\n** You can safely turn off the power\n");
-#ifdef CONFIG_MIPS_MIRAGE
- gpio_direction_output(210, 1);
-#endif
-#ifdef CONFIG_MIPS_DB1200
- au_writew(au_readw(0xB980001C) | (1 << 14), 0xB980001C);
-#endif
-#ifdef CONFIG_PM
- au_sleep();
-
- /* Should not get here */
- printk(KERN_ERR "Unable to put CPU in sleep mode\n");
- while (1);
-#else
- while (1)
- __asm__(".set\tmips3\n\t"
- "wait\n\t"
- ".set\tmips0");
-#endif
-#endif /* defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550) */
-}
-
-void au1000_power_off(void)
-{
- au1000_halt();
-}
diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
index 6184baa5678..561e5da2658 100644
--- a/arch/mips/alchemy/common/setup.c
+++ b/arch/mips/alchemy/common/setup.c
@@ -29,18 +29,13 @@
#include <linux/ioport.h>
#include <linux/jiffies.h>
#include <linux/module.h>
-#include <linux/pm.h>
#include <asm/mipsregs.h>
-#include <asm/reboot.h>
#include <asm/time.h>
#include <au1000.h>
extern void __init board_setup(void);
-extern void au1000_restart(char *);
-extern void au1000_halt(void);
-extern void au1000_power_off(void);
extern void set_cpuspec(void);
void __init plat_mem_setup(void)
@@ -57,10 +52,6 @@ void __init plat_mem_setup(void)
/* this is faster than wasting cycles trying to approximate it */
preset_lpj = (est_freq >> 1) / HZ;
- _machine_restart = au1000_restart;
- _machine_halt = au1000_halt;
- pm_power_off = au1000_power_off;
-
board_setup(); /* board specific setup */
if (au1xxx_cpu_needs_config_od())
@@ -78,37 +69,20 @@ void __init plat_mem_setup(void)
iomem_resource.end = IOMEM_RESOURCE_END;
}
-#if defined(CONFIG_64BIT_PHYS_ADDR)
+#if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_PCI)
/* This routine should be valid for all Au1x based boards */
phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
{
+ u32 start = (u32)Au1500_PCI_MEM_START;
+ u32 end = (u32)Au1500_PCI_MEM_END;
+
/* Don't fixup 36-bit addresses */
if ((phys_addr >> 32) != 0)
return phys_addr;
-#ifdef CONFIG_PCI
- {
- u32 start = (u32)Au1500_PCI_MEM_START;
- u32 end = (u32)Au1500_PCI_MEM_END;
-
- /* Check for PCI memory window */
- if (phys_addr >= start && (phys_addr + size - 1) <= end)
- return (phys_t)
- ((phys_addr - start) + Au1500_PCI_MEM_START);
- }
-#endif
-
- /*
- * All Au1xx0 SOCs have a PCMCIA controller.
- * We setup our 32-bit pseudo addresses to be equal to the
- * 36-bit addr >> 4, to make it easier to check the address
- * and fix it.
- * The PCMCIA socket 0 physical attribute address is 0xF 4000 0000.
- * The pseudo address we use is 0xF400 0000. Any address over
- * 0xF400 0000 is a PCMCIA pseudo address.
- */
- if ((phys_addr >= 0xF4000000) && (phys_addr < 0xFFFFFFFF))
- return (phys_t)(phys_addr << 4);
+ /* Check for PCI memory window */
+ if (phys_addr >= start && (phys_addr + size - 1) <= end)
+ return (phys_t)((phys_addr - start) + Au1500_PCI_MEM_START);
/* default nop */
return phys_addr;
diff --git a/arch/mips/alchemy/common/time.c b/arch/mips/alchemy/common/time.c
index 379a664809b..2aecb2fdf98 100644
--- a/arch/mips/alchemy/common/time.c
+++ b/arch/mips/alchemy/common/time.c
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2008 Manuel Lauss <mano@roarinelk.homelinux.net>
+ * Copyright (C) 2008-2009 Manuel Lauss <manuel.lauss@gmail.com>
*
* Previous incarnations were:
* Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
@@ -85,7 +85,6 @@ static struct clock_event_device au1x_rtcmatch2_clockdev = {
.name = "rtcmatch2",
.features = CLOCK_EVT_FEAT_ONESHOT,
.rating = 100,
- .irq = AU1000_RTC_MATCH2_INT,
.set_next_event = au1x_rtcmatch2_set_next_event,
.set_mode = au1x_rtcmatch2_set_mode,
.cpumask = cpu_all_mask,
@@ -98,11 +97,13 @@ static struct irqaction au1x_rtcmatch2_irqaction = {
.dev_id = &au1x_rtcmatch2_clockdev,
};
-void __init plat_time_init(void)
+static int __init alchemy_time_init(unsigned int m2int)
{
struct clock_event_device *cd = &au1x_rtcmatch2_clockdev;
unsigned long t;
+ au1x_rtcmatch2_clockdev.irq = m2int;
+
/* Check if firmware (YAMON, ...) has enabled 32kHz and clock
* has been detected. If so install the rtcmatch2 clocksource,
* otherwise don't bother. Note that both bits being set is by
@@ -148,13 +149,18 @@ void __init plat_time_init(void)
cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
cd->min_delta_ns = clockevent_delta2ns(8, cd); /* ~0.25ms */
clockevents_register_device(cd);
- setup_irq(AU1000_RTC_MATCH2_INT, &au1x_rtcmatch2_irqaction);
+ setup_irq(m2int, &au1x_rtcmatch2_irqaction);
printk(KERN_INFO "Alchemy clocksource installed\n");
- return;
+ return 0;
cntr_err:
+ return -1;
+}
+
+static void __init alchemy_setup_c0timer(void)
+{
/*
* MIPS kernel assigns 'au1k_wait' to 'cpu_wait' before this
* function is called. Because the Alchemy counters are unusable
@@ -166,3 +172,22 @@ cntr_err:
r4k_clockevent_init();
init_r4k_clocksource();
}
+
+static int alchemy_m2inttab[] __initdata = {
+ AU1000_RTC_MATCH2_INT,
+ AU1500_RTC_MATCH2_INT,
+ AU1100_RTC_MATCH2_INT,
+ AU1550_RTC_MATCH2_INT,
+ AU1200_RTC_MATCH2_INT,
+};
+
+void __init plat_time_init(void)
+{
+ int t;
+
+ t = alchemy_get_cputype();
+ if (t == ALCHEMY_CPU_UNKNOWN)
+ alchemy_setup_c0timer();
+ else if (alchemy_time_init(alchemy_m2inttab[t]))
+ alchemy_setup_c0timer();
+}
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 730f9f2b30e..ecbd37f9ee8 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -2,7 +2,7 @@
# Alchemy Develboards
#
-obj-y += prom.o
+obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
obj-$(CONFIG_MIPS_PB1000) += pb1000/
obj-$(CONFIG_MIPS_PB1100) += pb1100/
@@ -11,8 +11,10 @@ obj-$(CONFIG_MIPS_PB1500) += pb1500/
obj-$(CONFIG_MIPS_PB1550) += pb1550/
obj-$(CONFIG_MIPS_DB1000) += db1x00/
obj-$(CONFIG_MIPS_DB1100) += db1x00/
-obj-$(CONFIG_MIPS_DB1200) += pb1200/
+obj-$(CONFIG_MIPS_DB1200) += db1200/
obj-$(CONFIG_MIPS_DB1500) += db1x00/
obj-$(CONFIG_MIPS_DB1550) += db1x00/
obj-$(CONFIG_MIPS_BOSPORUS) += db1x00/
obj-$(CONFIG_MIPS_MIRAGE) += db1x00/
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/devboards/bcsr.c b/arch/mips/alchemy/devboards/bcsr.c
new file mode 100644
index 00000000000..3bc4fd2155d
--- /dev/null
+++ b/arch/mips/alchemy/devboards/bcsr.c
@@ -0,0 +1,148 @@
+/*
+ * bcsr.h -- Db1xxx/Pb1xxx Devboard CPLD registers ("BCSR") abstraction.
+ *
+ * All Alchemy development boards (except, of course, the weird PB1000)
+ * have a few registers in a CPLD with standardised layout; they mostly
+ * only differ in base address.
+ * All registers are 16bits wide with 32bit spacing.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+static struct bcsr_reg {
+ void __iomem *raddr;
+ spinlock_t lock;
+} bcsr_regs[BCSR_CNT];
+
+static void __iomem *bcsr_virt; /* KSEG1 addr of BCSR base */
+static int bcsr_csc_base; /* linux-irq of first cascaded irq */
+
+void __init bcsr_init(unsigned long bcsr1_phys, unsigned long bcsr2_phys)
+{
+ int i;
+
+ bcsr1_phys = KSEG1ADDR(CPHYSADDR(bcsr1_phys));
+ bcsr2_phys = KSEG1ADDR(CPHYSADDR(bcsr2_phys));
+
+ bcsr_virt = (void __iomem *)bcsr1_phys;
+
+ for (i = 0; i < BCSR_CNT; i++) {
+ if (i >= BCSR_HEXLEDS)
+ bcsr_regs[i].raddr = (void __iomem *)bcsr2_phys +
+ (0x04 * (i - BCSR_HEXLEDS));
+ else
+ bcsr_regs[i].raddr = (void __iomem *)bcsr1_phys +
+ (0x04 * i);
+
+ spin_lock_init(&bcsr_regs[i].lock);
+ }
+}
+
+unsigned short bcsr_read(enum bcsr_id reg)
+{
+ unsigned short r;
+ unsigned long flags;
+
+ spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+ r = __raw_readw(bcsr_regs[reg].raddr);
+ spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+ return r;
+}
+EXPORT_SYMBOL_GPL(bcsr_read);
+
+void bcsr_write(enum bcsr_id reg, unsigned short val)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+ __raw_writew(val, bcsr_regs[reg].raddr);
+ wmb();
+ spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+}
+EXPORT_SYMBOL_GPL(bcsr_write);
+
+void bcsr_mod(enum bcsr_id reg, unsigned short clr, unsigned short set)
+{
+ unsigned short r;
+ unsigned long flags;
+
+ spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+ r = __raw_readw(bcsr_regs[reg].raddr);
+ r &= ~clr;
+ r |= set;
+ __raw_writew(r, bcsr_regs[reg].raddr);
+ wmb();
+ spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+}
+EXPORT_SYMBOL_GPL(bcsr_mod);
+
+/*
+ * DB1200/PB1200 CPLD IRQ muxer
+ */
+static void bcsr_csc_handler(unsigned int irq, struct irq_desc *d)
+{
+ unsigned short bisr = __raw_readw(bcsr_virt + BCSR_REG_INTSTAT);
+
+ for ( ; bisr; bisr &= bisr - 1)
+ generic_handle_irq(bcsr_csc_base + __ffs(bisr));
+}
+
+/* NOTE: both the enable and mask bits must be cleared, otherwise the
+ * CPLD generates tons of spurious interrupts (at least on my DB1200).
+ * -- mlau
+ */
+static void bcsr_irq_mask(unsigned int irq_nr)
+{
+ unsigned short v = 1 << (irq_nr - bcsr_csc_base);
+ __raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
+ __raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
+ wmb();
+}
+
+static void bcsr_irq_maskack(unsigned int irq_nr)
+{
+ unsigned short v = 1 << (irq_nr - bcsr_csc_base);
+ __raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
+ __raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
+ __raw_writew(v, bcsr_virt + BCSR_REG_INTSTAT); /* ack */
+ wmb();
+}
+
+static void bcsr_irq_unmask(unsigned int irq_nr)
+{
+ unsigned short v = 1 << (irq_nr - bcsr_csc_base);
+ __raw_writew(v, bcsr_virt + BCSR_REG_INTSET);
+ __raw_writew(v, bcsr_virt + BCSR_REG_MASKSET);
+ wmb();
+}
+
+static struct irq_chip bcsr_irq_type = {
+ .name = "CPLD",
+ .mask = bcsr_irq_mask,
+ .mask_ack = bcsr_irq_maskack,
+ .unmask = bcsr_irq_unmask,
+};
+
+void __init bcsr_init_irq(int csc_start, int csc_end, int hook_irq)
+{
+ unsigned int irq;
+
+ /* mask & disable & ack all */
+ __raw_writew(0xffff, bcsr_virt + BCSR_REG_INTCLR);
+ __raw_writew(0xffff, bcsr_virt + BCSR_REG_MASKCLR);
+ __raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSTAT);
+ wmb();
+
+ bcsr_csc_base = csc_start;
+
+ for (irq = csc_start; irq <= csc_end; irq++)
+ set_irq_chip_and_handler_name(irq, &bcsr_irq_type,
+ handle_level_irq, "level");
+
+ set_irq_chained_handler(hook_irq, bcsr_csc_handler);
+}
diff --git a/arch/mips/alchemy/devboards/db1200/Makefile b/arch/mips/alchemy/devboards/db1200/Makefile
new file mode 100644
index 00000000000..17840a5e273
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200/Makefile
@@ -0,0 +1 @@
+obj-y += setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1200/platform.c b/arch/mips/alchemy/devboards/db1200/platform.c
new file mode 100644
index 00000000000..3cb95a98ab3
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200/platform.c
@@ -0,0 +1,561 @@
+/*
+ * DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008-2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/smc91x.h>
+
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-db1x00/db1200.h>
+
+#include "../platform.h"
+
+static struct mtd_partition db1200_spiflash_parts[] = {
+ {
+ .name = "DB1200 SPI flash",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct flash_platform_data db1200_spiflash_data = {
+ .name = "s25fl001",
+ .parts = db1200_spiflash_parts,
+ .nr_parts = ARRAY_SIZE(db1200_spiflash_parts),
+ .type = "m25p10",
+};
+
+static struct spi_board_info db1200_spi_devs[] __initdata = {
+ {
+ /* TI TMP121AIDBVR temp sensor */
+ .modalias = "tmp121",
+ .max_speed_hz = 2000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ .mode = 0,
+ },
+ {
+ /* Spansion S25FL001D0FMA SPI flash */
+ .modalias = "m25p80",
+ .max_speed_hz = 50000000,
+ .bus_num = 0,
+ .chip_select = 1,
+ .mode = 0,
+ .platform_data = &db1200_spiflash_data,
+ },
+};
+
+static struct i2c_board_info db1200_i2c_devs[] __initdata = {
+ {
+ /* AT24C04-10 I2C eeprom */
+ I2C_BOARD_INFO("24c04", 0x52),
+ },
+ {
+ /* Philips NE1619 temp/voltage sensor (adm1025 drv) */
+ I2C_BOARD_INFO("ne1619", 0x2d),
+ },
+ {
+ /* I2S audio codec WM8731 */
+ I2C_BOARD_INFO("wm8731", 0x1b),
+ },
+};
+
+/**********************************************************************/
+
+static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+ ioaddr &= 0xffffff00;
+
+ if (ctrl & NAND_CLE) {
+ ioaddr += MEM_STNAND_CMD;
+ } else if (ctrl & NAND_ALE) {
+ ioaddr += MEM_STNAND_ADDR;
+ } else {
+ /* assume we want to r/w real data by default */
+ ioaddr += MEM_STNAND_DATA;
+ }
+ this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+ if (cmd != NAND_CMD_NONE) {
+ __raw_writeb(cmd, this->IO_ADDR_W);
+ wmb();
+ }
+}
+
+static int au1200_nand_device_ready(struct mtd_info *mtd)
+{
+ return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1200_nand_parts[] = {
+ {
+ .name = "NAND FS 0",
+ .offset = 0,
+ .size = 8 * 1024 * 1024,
+ },
+ {
+ .name = "NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+struct platform_nand_data db1200_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(db1200_nand_parts),
+ .partitions = db1200_nand_parts,
+ .chip_delay = 20,
+ .part_probe_types = db1200_part_probes,
+ },
+ .ctrl = {
+ .dev_ready = au1200_nand_device_ready,
+ .cmd_ctrl = au1200_nand_cmd_ctrl,
+ },
+};
+
+static struct resource db1200_nand_res[] = {
+ [0] = {
+ .start = DB1200_NAND_PHYS_ADDR,
+ .end = DB1200_NAND_PHYS_ADDR + 0xff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device db1200_nand_dev = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(db1200_nand_res),
+ .resource = db1200_nand_res,
+ .id = -1,
+ .dev = {
+ .platform_data = &db1200_nand_platdata,
+ }
+};
+
+/**********************************************************************/
+
+static struct smc91x_platdata db1200_eth_data = {
+ .flags = SMC91X_NOWAIT | SMC91X_USE_16BIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource db1200_eth_res[] = {
+ [0] = {
+ .start = DB1200_ETH_PHYS_ADDR,
+ .end = DB1200_ETH_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_ETH_INT,
+ .end = DB1200_ETH_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device db1200_eth_dev = {
+ .dev = {
+ .platform_data = &db1200_eth_data,
+ },
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(db1200_eth_res),
+ .resource = db1200_eth_res,
+};
+
+/**********************************************************************/
+
+static struct resource db1200_ide_res[] = {
+ [0] = {
+ .start = DB1200_IDE_PHYS_ADDR,
+ .end = DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = DB1200_IDE_INT,
+ .end = DB1200_IDE_INT,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 ide_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device db1200_ide_dev = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ide_dmamask,
+ .coherent_dma_mask = DMA_32BIT_MASK,
+ },
+ .num_resources = ARRAY_SIZE(db1200_ide_res),
+ .resource = db1200_ide_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1200_rtc_dev = {
+ .name = "rtc-au1xxx",
+ .id = -1,
+};
+
+/**********************************************************************/
+
+/* SD carddetects: they're supposed to be edge-triggered, but ack
+ * doesn't seem to work (CPLD Rev 2). Instead, the screaming one
+ * is disabled and its counterpart enabled. The 500ms timeout is
+ * because the carddetect isn't debounced in hardware.
+ */
+static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
+{
+ void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+ if (irq == DB1200_SD0_INSERT_INT) {
+ disable_irq_nosync(DB1200_SD0_INSERT_INT);
+ enable_irq(DB1200_SD0_EJECT_INT);
+ } else {
+ disable_irq_nosync(DB1200_SD0_EJECT_INT);
+ enable_irq(DB1200_SD0_INSERT_INT);
+ }
+
+ /* link against CONFIG_MMC=m */
+ mmc_cd = symbol_get(mmc_detect_change);
+ if (mmc_cd) {
+ mmc_cd(ptr, msecs_to_jiffies(500));
+ symbol_put(mmc_detect_change);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int db1200_mmc_cd_setup(void *mmc_host, int en)
+{
+ int ret;
+
+ if (en) {
+ ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_insert", mmc_host);
+ if (ret)
+ goto out;
+
+ ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
+ IRQF_DISABLED, "sd_eject", mmc_host);
+ if (ret) {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ goto out;
+ }
+
+ if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
+ enable_irq(DB1200_SD0_EJECT_INT);
+ else
+ enable_irq(DB1200_SD0_INSERT_INT);
+
+ } else {
+ free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+ free_irq(DB1200_SD0_EJECT_INT, mmc_host);
+ }
+ ret = 0;
+out:
+ return ret;
+}
+
+static void db1200_mmc_set_power(void *mmc_host, int state)
+{
+ if (state) {
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+ msleep(400); /* stabilization time */
+ } else
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+}
+
+static int db1200_mmc_card_readonly(void *mmc_host)
+{
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int db1200_mmc_card_inserted(void *mmc_host)
+{
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void db1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF)
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+ else
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1200_mmc_led = {
+ .brightness_set = db1200_mmcled_set,
+};
+
+/* needed by arch/mips/alchemy/common/platform.c */
+struct au1xmmc_platform_data au1xmmc_platdata[] = {
+ [0] = {
+ .cd_setup = db1200_mmc_cd_setup,
+ .set_power = db1200_mmc_set_power,
+ .card_inserted = db1200_mmc_card_inserted,
+ .card_readonly = db1200_mmc_card_readonly,
+ .led = &db1200_mmc_led,
+ },
+};
+
+/**********************************************************************/
+
+static struct resource au1200_psc0_res[] = {
+ [0] = {
+ .start = PSC0_PHYS_ADDR,
+ .end = PSC0_PHYS_ADDR + 0x000fffff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC0_INT,
+ .end = AU1200_PSC0_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = DSCR_CMD0_PSC0_TX,
+ .end = DSCR_CMD0_PSC0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = DSCR_CMD0_PSC0_RX,
+ .end = DSCR_CMD0_PSC0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1200_i2c_dev = {
+ .name = "au1xpsc_smbus",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+ if (cs)
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
+ else
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1200_spi_platdata = {
+ .mainclk_hz = 50000000, /* PSC0 clock */
+ .num_chipselect = 2,
+ .activate_cs = db1200_spi_cs_en,
+};
+
+static u64 spi_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device db1200_spi_dev = {
+ .dev = {
+ .dma_mask = &spi_dmamask,
+ .coherent_dma_mask = DMA_32BIT_MASK,
+ .platform_data = &db1200_spi_platdata,
+ },
+ .name = "au1550-spi",
+ .id = 0, /* bus number */
+ .num_resources = ARRAY_SIZE(au1200_psc0_res),
+ .resource = au1200_psc0_res,
+};
+
+static struct resource au1200_psc1_res[] = {
+ [0] = {
+ .start = PSC1_PHYS_ADDR,
+ .end = PSC1_PHYS_ADDR + 0x000fffff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC1_INT,
+ .end = AU1200_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = DSCR_CMD0_PSC1_TX,
+ .end = DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = DSCR_CMD0_PSC1_RX,
+ .end = DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1200_audio_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1200_psc1_res),
+ .resource = au1200_psc1_res,
+};
+
+static struct platform_device *db1200_devs[] __initdata = {
+ NULL, /* PSC0, selected by S6.8 */
+ &db1200_ide_dev,
+ &db1200_eth_dev,
+ &db1200_rtc_dev,
+ &db1200_nand_dev,
+ &db1200_audio_dev,
+};
+
+static int __init db1200_dev_init(void)
+{
+ unsigned long pfc;
+ unsigned short sw;
+ int swapped;
+
+ i2c_register_board_info(0, db1200_i2c_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+ spi_register_board_info(db1200_spi_devs,
+ ARRAY_SIZE(db1200_i2c_devs));
+
+ /* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
+ * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
+ */
+
+ /* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
+ * this pin is claimed by PSC0 (unused though, but pinmux doesn't
+ * allow to free it without crippling the SPI interface).
+ * As a result, in SPI mode, OTG simply won't work (PSC0 uses
+ * it as an input pin which is pulled high on the boards).
+ */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
+
+ /* switch off OTG VBUS supply */
+ gpio_request(215, "otg-vbus");
+ gpio_direction_output(215, 1);
+
+ printk(KERN_INFO "DB1200 device configuration:\n");
+
+ sw = bcsr_read(BCSR_SWITCHES);
+ if (sw & BCSR_SWITCHES_DIP_8) {
+ db1200_devs[0] = &db1200_i2c_dev;
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+ pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
+ printk(KERN_INFO " OTG port VBUS supply available!\n");
+ } else {
+ db1200_devs[0] = &db1200_spi_dev;
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
+
+ pfc |= (1 << 17); /* PSC0 owns GPIO215 */
+
+ printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
+ printk(KERN_INFO " OTG port VBUS supply disabled\n");
+ }
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
+ * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
+ */
+ sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
+ if (sw == BCSR_SWITCHES_DIP_8) {
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
+ db1200_audio_dev.name = "au1xpsc_i2s";
+ printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
+ } else {
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
+ db1200_audio_dev.name = "au1xpsc_ac97";
+ printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
+ }
+
+ /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+ PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR,
+ PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_IO_PHYS_ADDR,
+ PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1200_PC0_INT,
+ DB1200_PC0_INSERT_INT,
+ /*DB1200_PC0_STSCHG_INT*/0,
+ DB1200_PC0_EJECT_INT,
+ 0);
+
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1200_PC1_INT,
+ DB1200_PC1_INSERT_INT,
+ /*DB1200_PC1_STSCHG_INT*/0,
+ DB1200_PC1_EJECT_INT,
+ 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(64 << 20, 2, swapped);
+
+ return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+}
+device_initcall(db1200_dev_init);
+
+/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
+int board_au1200fb_panel(void)
+{
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
+ return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1200/setup.c b/arch/mips/alchemy/devboards/db1200/setup.c
new file mode 100644
index 00000000000..379536e3abd
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200/setup.c
@@ -0,0 +1,118 @@
+/*
+ * Alchemy/AMD/RMI DB1200 board setup.
+ *
+ * Licensed under the terms outlined in the file COPYING in the root of
+ * this source archive.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-db1x00/db1200.h>
+
+const char *get_system_type(void)
+{
+ return "Alchemy Db1200";
+}
+
+void __init board_setup(void)
+{
+ unsigned long freq0, clksrc, div, pfc;
+ unsigned short whoami;
+
+ bcsr_init(DB1200_BCSR_PHYS_ADDR,
+ DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+
+ whoami = bcsr_read(BCSR_WHOAMI);
+ printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
+ " Board-ID %d Daughtercard ID %d\n",
+ (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+ /* SMBus/SPI on PSC0, Audio on PSC1 */
+ pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
+ pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
+ pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
+ __raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+ wmb();
+
+ /* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
+ * CPU clock; all other clock generators off/unused.
+ */
+ div = (get_au1x00_speed() + 25000000) / 50000000;
+ if (div & 1)
+ div++;
+ div = ((div >> 1) - 1) & 0xff;
+
+ freq0 = div << SYS_FC_FRDIV0_BIT;
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+ freq0 |= SYS_FC_FE0; /* enable F0 */
+ __raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+ wmb();
+
+ /* psc0_intclk comes 1:1 from F0 */
+ clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
+ __raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
+ wmb();
+}
+
+/* use the hexleds to count the number of times the cpu has entered
+ * wait, the dots to indicate whether the CPU is currently idle or
+ * active (dots off = sleeping, dots on = working) for cases where
+ * the number doesn't change for a long(er) period of time.
+ */
+static void db1200_wait(void)
+{
+ __asm__(" .set push \n"
+ " .set mips3 \n"
+ " .set noreorder \n"
+ " cache 0x14, 0(%0) \n"
+ " cache 0x14, 32(%0) \n"
+ " cache 0x14, 64(%0) \n"
+ /* dots off: we're about to call wait */
+ " lui $26, 0xb980 \n"
+ " ori $27, $0, 3 \n"
+ " sb $27, 0x18($26) \n"
+ " sync \n"
+ " nop \n"
+ " wait \n"
+ " nop \n"
+ " nop \n"
+ " nop \n"
+ " nop \n"
+ " nop \n"
+ /* dots on: there's work to do, increment cntr */
+ " lui $26, 0xb980 \n"
+ " sb $0, 0x18($26) \n"
+ " lui $26, 0xb9c0 \n"
+ " lb $27, 0($26) \n"
+ " addiu $27, $27, 1 \n"
+ " sb $27, 0($26) \n"
+ " sync \n"
+ " .set pop \n"
+ : : "r" (db1200_wait));
+}
+
+static int __init db1200_arch_init(void)
+{
+ /* GPIO7 is low-level triggered CPLD cascade */
+ set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
+
+ /* do not autoenable these: CPLD has broken edge int handling,
+ * and the CD handler setup requires manual enabling to work
+ * around that.
+ */
+ irq_to_desc(DB1200_SD0_INSERT_INT)->status |= IRQ_NOAUTOEN;
+ irq_to_desc(DB1200_SD0_EJECT_INT)->status |= IRQ_NOAUTOEN;
+
+ if (cpu_wait)
+ cpu_wait = db1200_wait;
+
+ return 0;
+}
+arch_initcall(db1200_arch_init);
diff --git a/arch/mips/alchemy/devboards/db1x00/Makefile b/arch/mips/alchemy/devboards/db1x00/Makefile
index 432241ab867..613c0c0c8be 100644
--- a/arch/mips/alchemy/devboards/db1x00/Makefile
+++ b/arch/mips/alchemy/devboards/db1x00/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
#
-obj-y := board_setup.o irqmap.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
index de30d8ea717..50c9bef99da 100644
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ b/arch/mips/alchemy/devboards/db1x00/board_setup.c
@@ -29,59 +29,139 @@
#include <linux/gpio.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
#include <asm/mach-db1x00/db1x00.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/reboot.h>
#include <prom.h>
+#ifdef CONFIG_MIPS_DB1500
+char irq_tab_alchemy[][5] __initdata = {
+ [12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - HPT371 */
+ [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
+};
+
+#endif
-static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+#ifdef CONFIG_MIPS_DB1550
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, AU1550_PCI_INTC, 0xff, 0xff, 0xff }, /* IDSEL 11 - on-board HPT371 */
+ [12] = { -1, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD, AU1550_PCI_INTA }, /* IDSEL 12 - PCI slot 2 (left) */
+ [13] = { -1, AU1550_PCI_INTA, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD }, /* IDSEL 13 - PCI slot 1 (right) */
+};
+#endif
+
+
+#ifdef CONFIG_MIPS_BOSPORUS
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 11 - miniPCI */
+ [12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - SN1741 */
+ [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
+};
+
+/*
+ * Micrel/Kendin 5 port switch attached to MAC0,
+ * MAC0 is associated with PHY address 5 (== WAN port)
+ * MAC1 is not associated with any PHY, since it's connected directly
+ * to the switch.
+ * no interrupts are used
+ */
+static struct au1000_eth_platform_data eth0_pdata = {
+ .phy_static_config = 1,
+ .phy_addr = 5,
+};
+
+static void bosporus_power_off(void)
+{
+ printk(KERN_INFO "It's now safe to turn off power\n");
+ while (1)
+ asm volatile (".set mips3 ; wait ; .set mips0");
+}
const char *get_system_type(void)
{
-#ifdef CONFIG_MIPS_BOSPORUS
return "Alchemy Bosporus Gateway Reference";
-#else
- return "Alchemy Db1x00";
+}
#endif
+
+
+#ifdef CONFIG_MIPS_MIRAGE
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, AU1500_PCI_INTD, 0xff, 0xff, 0xff }, /* IDSEL 11 - SMI VGX */
+ [12] = { -1, 0xff, 0xff, AU1500_PCI_INTC, 0xff }, /* IDSEL 12 - PNX1300 */
+ [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 13 - miniPCI */
+};
+
+static void mirage_power_off(void)
+{
+ alchemy_gpio_direction_output(210, 1);
+}
+
+const char *get_system_type(void)
+{
+ return "Alchemy Mirage";
+}
+#endif
+
+
+#if defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
+static void mips_softreset(void)
+{
+ asm volatile ("jr\t%0" : : "r"(0xbfc00000));
}
-void board_reset(void)
+#else
+
+const char *get_system_type(void)
{
- /* Hit BCSR.SW_RESET[RESET] */
- bcsr->swreset = 0x0000;
+ return "Alchemy Db1x00";
}
+#endif
+
void __init board_setup(void)
{
- u32 pin_func = 0;
- char *argptr;
-
- argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
+ unsigned long bcsr1, bcsr2;
+ u32 pin_func;
+
+ bcsr1 = DB1000_BCSR_PHYS_ADDR;
+ bcsr2 = DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS;
+
+ pin_func = 0;
+
+#ifdef CONFIG_MIPS_DB1000
+ printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1500
+ printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
#endif
+#ifdef CONFIG_MIPS_DB1100
+ printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+#endif
+#ifdef CONFIG_MIPS_BOSPORUS
+ au1xxx_override_eth_cfg(0, &eth0_pdata);
-#ifdef CONFIG_FB_AU1100
- argptr = strstr(argptr, "video=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- /* default panel */
- /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
- }
+ printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
#endif
+#ifdef CONFIG_MIPS_MIRAGE
+ printk(KERN_INFO "AMD Alchemy Mirage Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1550
+ printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
-#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
- /* au1000 does not support vra, au1500 and au1100 do */
- strcat(argptr, " au1000_audio=vra");
- argptr = prom_getcmdline();
+ bcsr1 = DB1550_BCSR_PHYS_ADDR;
+ bcsr2 = DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS;
#endif
+ /* initialize board register space */
+ bcsr_init(bcsr1, bcsr2);
+
/* Not valid for Au1550 */
#if defined(CONFIG_IRDA) && \
(defined(CONFIG_SOC_AU1000) || defined(CONFIG_SOC_AU1100))
@@ -89,11 +169,10 @@ void __init board_setup(void)
pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
au_writel(pin_func, SYS_PINFUNC);
/* Power off until the driver is in use */
- bcsr->resets &= ~BCSR_RESETS_IRDA_MODE_MASK;
- bcsr->resets |= BCSR_RESETS_IRDA_MODE_OFF;
- au_sync();
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
+ BCSR_RESETS_IRDA_MODE_OFF);
#endif
- bcsr->pcmcia = 0x0000; /* turn off PCMCIA power */
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
/* Enable GPIO[31:0] inputs */
alchemy_gpio1_input_enable();
@@ -120,26 +199,53 @@ void __init board_setup(void)
* be part of the audio driver.
*/
alchemy_gpio_direction_output(209, 1);
-#endif
-
- au_sync();
-#ifdef CONFIG_MIPS_DB1000
- printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
- printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
- printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+ pm_power_off = mirage_power_off;
+ _machine_halt = mirage_power_off;
+ _machine_restart = (void(*)(char *))mips_softreset;
#endif
+
#ifdef CONFIG_MIPS_BOSPORUS
- printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
+ pm_power_off = bosporus_power_off;
+ _machine_halt = bosporus_power_off;
+ _machine_restart = (void(*)(char *))mips_softreset;
#endif
-#ifdef CONFIG_MIPS_MIRAGE
- printk(KERN_INFO "AMD Alchemy Mirage Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1550
- printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
+ au_sync();
+}
+
+static int __init db1x00_init_irq(void)
+{
+#if defined(CONFIG_MIPS_MIRAGE)
+ set_irq_type(AU1500_GPIO7_INT, IRQF_TRIGGER_RISING); /* TS pendown */
+#elif defined(CONFIG_MIPS_DB1550)
+ set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW); /* CD1# */
+ set_irq_type(AU1550_GPIO3_INT, IRQF_TRIGGER_LOW); /* CARD0# */
+ set_irq_type(AU1550_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
+ set_irq_type(AU1550_GPIO21_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ set_irq_type(AU1550_GPIO22_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
+#elif defined(CONFIG_MIPS_DB1500)
+ set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
+ set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
+ set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
+ set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
+#elif defined(CONFIG_MIPS_DB1100)
+ set_irq_type(AU1100_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ set_irq_type(AU1100_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
+ set_irq_type(AU1100_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
+ set_irq_type(AU1100_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
+ set_irq_type(AU1100_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ set_irq_type(AU1100_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
+#elif defined(CONFIG_MIPS_DB1000)
+ set_irq_type(AU1000_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ set_irq_type(AU1000_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
+ set_irq_type(AU1000_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
+ set_irq_type(AU1000_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
+ set_irq_type(AU1000_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ set_irq_type(AU1000_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
#endif
+ return 0;
}
+arch_initcall(db1x00_init_irq);
diff --git a/arch/mips/alchemy/devboards/db1x00/irqmap.c b/arch/mips/alchemy/devboards/db1x00/irqmap.c
deleted file mode 100644
index 0b09025087c..00000000000
--- a/arch/mips/alchemy/devboards/db1x00/irqmap.c
+++ /dev/null
@@ -1,90 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_MIPS_DB1500
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT371 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_BOSPORUS
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 11 - miniPCI */
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - SN1741 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_MIRAGE
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTD, INTX, INTX, INTX }, /* IDSEL 11 - SMI VGX */
- [12] = { -1, INTX, INTX, INTC, INTX }, /* IDSEL 12 - PNX1300 */
- [13] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 13 - miniPCI */
-};
-#endif
-
-#ifdef CONFIG_MIPS_DB1550
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTC, INTX, INTX, INTX }, /* IDSEL 11 - on-board HPT371 */
- [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-#endif
-
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-
-#ifndef CONFIG_MIPS_MIRAGE
-#ifdef CONFIG_MIPS_DB1550
- { AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 IRQ# */
- { AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 IRQ# */
-#else
- { AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 Fully_Interted# */
- { AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 STSCHG# */
- { AU1000_GPIO_2, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 IRQ# */
-
- { AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 Fully_Interted# */
- { AU1000_GPIO_4, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 STSCHG# */
- { AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 IRQ# */
-#endif
-#else
- { AU1000_GPIO_7, IRQF_TRIGGER_RISING, 0 }, /* touchscreen pen down */
-#endif
-
-};
-
-void __init board_init_irq(void)
-{
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
new file mode 100644
index 00000000000..978d5ab3d67
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1x00/platform.c
@@ -0,0 +1,118 @@
+/*
+ * DBAu1xxx board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-au1x00/au1xxx.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include "../platform.h"
+
+/* DB1xxx PCMCIA interrupt sources:
+ * CD0/1 GPIO0/3
+ * STSCHG0/1 GPIO1/4
+ * CARD0/1 GPIO2/5
+ * Db1550: 0/1, 21/22, 3/5
+ */
+
+#define DB1XXX_HAS_PCMCIA
+#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
+
+#if defined(CONFIG_MIPS_DB1000)
+#define DB1XXX_PCMCIA_CD0 AU1000_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1000_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1000_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1000_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1000_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1000_GPIO5_INT
+#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
+#define BOARD_FLASH_WIDTH 4 /* 32-bits */
+#elif defined(CONFIG_MIPS_DB1100)
+#define DB1XXX_PCMCIA_CD0 AU1100_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1100_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1100_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1100_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1100_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1100_GPIO5_INT
+#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
+#define BOARD_FLASH_WIDTH 4 /* 32-bits */
+#elif defined(CONFIG_MIPS_DB1500)
+#define DB1XXX_PCMCIA_CD0 AU1500_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1500_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0 AU1500_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1 AU1500_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1500_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1 AU1500_GPIO5_INT
+#define BOARD_FLASH_SIZE 0x02000000 /* 32MB */
+#define BOARD_FLASH_WIDTH 4 /* 32-bits */
+#elif defined(CONFIG_MIPS_DB1550)
+#define DB1XXX_PCMCIA_CD0 AU1550_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0 AU1550_GPIO21_INT
+#define DB1XXX_PCMCIA_CARD0 AU1550_GPIO3_INT
+#define DB1XXX_PCMCIA_CD1 AU1550_GPIO1_INT
+#define DB1XXX_PCMCIA_STSCHG1 AU1550_GPIO22_INT
+#define DB1XXX_PCMCIA_CARD1 AU1550_GPIO5_INT
+#define BOARD_FLASH_SIZE 0x08000000 /* 128MB */
+#define BOARD_FLASH_WIDTH 4 /* 32-bits */
+#else
+/* other board: no PCMCIA */
+#undef DB1XXX_HAS_PCMCIA
+#undef F_SWAPPED
+#define F_SWAPPED 0
+#if defined(CONFIG_MIPS_BOSPORUS)
+#define BOARD_FLASH_SIZE 0x01000000 /* 16MB */
+#define BOARD_FLASH_WIDTH 2 /* 16-bits */
+#elif defined(CONFIG_MIPS_MIRAGE)
+#define BOARD_FLASH_SIZE 0x04000000 /* 64MB */
+#define BOARD_FLASH_WIDTH 4 /* 32-bits */
+#endif
+#endif
+
+static int __init db1xxx_dev_init(void)
+{
+#ifdef DB1XXX_HAS_PCMCIA
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+ PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR,
+ PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_IO_PHYS_ADDR,
+ PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ DB1XXX_PCMCIA_CARD0,
+ DB1XXX_PCMCIA_CD0,
+ /*DB1XXX_PCMCIA_STSCHG0*/0,
+ 0,
+ 0);
+
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+ PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR + 0x004000000,
+ PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
+ PCMCIA_IO_PHYS_ADDR + 0x004000000,
+ PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
+ DB1XXX_PCMCIA_CARD1,
+ DB1XXX_PCMCIA_CD1,
+ /*DB1XXX_PCMCIA_STSCHG1*/0,
+ 0,
+ 1);
+#endif
+ db1x_register_norflash(BOARD_FLASH_SIZE, BOARD_FLASH_WIDTH, F_SWAPPED);
+ return 0;
+}
+device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1000/board_setup.c b/arch/mips/alchemy/devboards/pb1000/board_setup.c
index cd273545e81..b5311d8a29a 100644
--- a/arch/mips/alchemy/devboards/pb1000/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1000/board_setup.c
@@ -31,11 +31,7 @@
#include <asm/mach-pb1x00/pb1000.h>
#include <prom.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_15, IRQF_TRIGGER_LOW, 0 },
-};
-
+#include "../platform.h"
const char *get_system_type(void)
{
@@ -46,25 +42,14 @@ void board_reset(void)
{
}
-void __init board_init_irq(void)
-{
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
-
void __init board_setup(void)
{
u32 pin_func, static_cfg0;
u32 sys_freqctrl, sys_clksrc;
u32 prid = read_c0_prid();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- char *argptr = prom_getcmdline();
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
+ sys_freqctrl = 0;
+ sys_clksrc = 0;
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
@@ -193,3 +178,16 @@ void __init board_setup(void)
break;
}
}
+
+static int __init pb1000_init_irq(void)
+{
+ set_irq_type(AU1000_GPIO15_INT, IRQF_TRIGGER_LOW);
+ return 0;
+}
+arch_initcall(pb1000_init_irq);
+
+static int __init pb1000_device_init(void)
+{
+ return db1x_register_norflash(8 * 1024 * 1024, 4, 0);
+}
+device_initcall(pb1000_device_init);
diff --git a/arch/mips/alchemy/devboards/pb1100/Makefile b/arch/mips/alchemy/devboards/pb1100/Makefile
index c586dd7e91d..7e3756c83fe 100644
--- a/arch/mips/alchemy/devboards/pb1100/Makefile
+++ b/arch/mips/alchemy/devboards/pb1100/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor Pb1100 board.
#
-obj-y := board_setup.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1100/board_setup.c b/arch/mips/alchemy/devboards/pb1100/board_setup.c
index 61263081ef5..c7b4caa81a3 100644
--- a/arch/mips/alchemy/devboards/pb1100/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1100/board_setup.c
@@ -29,19 +29,11 @@
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1100.h>
+#include <asm/mach-db1x00/bcsr.h>
#include <prom.h>
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_9, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card Fully_Inserted# */
- { AU1000_GPIO_10, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card STSCHG# */
- { AU1000_GPIO_11, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card IRQ# */
- { AU1000_GPIO_13, IRQF_TRIGGER_LOW, 0 }, /* DC_IRQ# */
-};
-
-
const char *get_system_type(void)
{
return "Alchemy Pb1100";
@@ -49,43 +41,15 @@ const char *get_system_type(void)
void board_reset(void)
{
- /* Hit BCSR.RST_VDDI[SOFT_RESET] */
- au_writel(0x00000000, PB1100_RST_VDDI);
-}
-
-void __init board_init_irq(void)
-{
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
+ bcsr_write(BCSR_SYSTEM, 0);
}
void __init board_setup(void)
{
volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
- char *argptr;
-
- argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
-
-#ifdef CONFIG_FB_AU1100
- argptr = strstr(argptr, "video=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- /* default panel */
- /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
- }
-#endif
-#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
- /* au1000 does not support vra, au1500 and au1100 do */
- strcat(argptr, " au1000_audio=vra");
- argptr = prom_getcmdline();
-#endif
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
@@ -155,3 +119,14 @@ void __init board_setup(void)
au_sync();
}
}
+
+static int __init pb1100_init_irq(void)
+{
+ set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
+ set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
+ set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
+ set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
+
+ return 0;
+}
+arch_initcall(pb1100_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1100/platform.c b/arch/mips/alchemy/devboards/pb1100/platform.c
new file mode 100644
index 00000000000..2c8dc29759f
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1100/platform.c
@@ -0,0 +1,50 @@
+/*
+ * Pb1100 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
+
+static int __init pb1100_dev_init(void)
+{
+ int swapped;
+
+ /* PCMCIA. single socket, identical to Pb1500 */
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+ PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR,
+ PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_IO_PHYS_ADDR,
+ PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1100_GPIO11_INT, /* card */
+ AU1100_GPIO9_INT, /* insert */
+ /*AU1100_GPIO10_INT*/0, /* stschg */
+ 0, /* eject */
+ 0); /* id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+
+ return 0;
+}
+device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1200/Makefile b/arch/mips/alchemy/devboards/pb1200/Makefile
index c8c3a99fb68..2ea9b02ef09 100644
--- a/arch/mips/alchemy/devboards/pb1200/Makefile
+++ b/arch/mips/alchemy/devboards/pb1200/Makefile
@@ -2,6 +2,6 @@
# Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
#
-obj-y := board_setup.o irqmap.o platform.o
+obj-y := board_setup.o platform.o
EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/devboards/pb1200/board_setup.c b/arch/mips/alchemy/devboards/pb1200/board_setup.c
index 94e6b7e7753..3184063f804 100644
--- a/arch/mips/alchemy/devboards/pb1200/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1200/board_setup.c
@@ -25,11 +25,23 @@
*/
#include <linux/init.h>
+#include <linux/interrupt.h>
#include <linux/sched.h>
-#include <prom.h>
-#include <au1xxx.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#ifdef CONFIG_MIPS_PB1200
+#include <asm/mach-pb1x00/pb1200.h>
+#endif
+
+#ifdef CONFIG_MIPS_DB1200
+#include <asm/mach-db1x00/db1200.h>
+#define PB1200_INT_BEGIN DB1200_INT_BEGIN
+#define PB1200_INT_END DB1200_INT_END
+#endif
+#include <prom.h>
const char *get_system_type(void)
{
@@ -38,25 +50,15 @@ const char *get_system_type(void)
void board_reset(void)
{
- bcsr->resets = 0;
- bcsr->system = 0;
+ bcsr_write(BCSR_RESETS, 0);
+ bcsr_write(BCSR_SYSTEM, 0);
}
void __init board_setup(void)
{
- char *argptr;
-
- argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
-#ifdef CONFIG_FB_AU1200
- strcat(argptr, " video=au1200fb:panel:bs");
-#endif
+ printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
+ bcsr_init(PB1200_BCSR_PHYS_ADDR,
+ PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
#if 0
{
@@ -82,7 +84,7 @@ void __init board_setup(void)
u32 pin_func;
/* Select SMBus in CPLD */
- bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
pin_func = au_readl(SYS_PINFUNC);
au_sync();
@@ -116,38 +118,54 @@ void __init board_setup(void)
/*
* The Pb1200 development board uses external MUX for PSC0 to
- * support SMB/SPI. bcsr->resets bit 12: 0=SMB 1=SPI
+ * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
*/
#ifdef CONFIG_I2C_AU1550
- bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
#endif
au_sync();
+}
-#ifdef CONFIG_MIPS_PB1200
- printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1200
- printk(KERN_INFO "AMD Alchemy Db1200 Board\n");
-#endif
+static int __init pb1200_init_irq(void)
+{
+ /* We have a problem with CPLD rev 3. */
+ if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
+ printk(KERN_ERR "updated to latest revision. This software will\n");
+ printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ panic("Game over. Your score is 0.");
+ }
+
+ set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+ bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
+
+ return 0;
}
+arch_initcall(pb1200_init_irq);
+
int board_au1200fb_panel(void)
{
- BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
- int p;
-
- p = bcsr->switches;
- p >>= 8;
- p &= 0x0F;
- return p;
+ return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
}
int board_au1200fb_panel_init(void)
{
/* Apply power */
- BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-
- bcsr->board |= BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD | BCSR_BOARD_LCDBL;
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
/* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
return 0;
}
@@ -155,10 +173,8 @@ int board_au1200fb_panel_init(void)
int board_au1200fb_panel_shutdown(void)
{
/* Remove power */
- BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-
- bcsr->board &= ~(BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL, 0);
/* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
return 0;
}
diff --git a/arch/mips/alchemy/devboards/pb1200/irqmap.c b/arch/mips/alchemy/devboards/pb1200/irqmap.c
deleted file mode 100644
index fe47498da28..00000000000
--- a/arch/mips/alchemy/devboards/pb1200/irqmap.c
+++ /dev/null
@@ -1,134 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_MIPS_PB1200
-#include <asm/mach-pb1x00/pb1200.h>
-#endif
-
-#ifdef CONFIG_MIPS_DB1200
-#include <asm/mach-db1x00/db1200.h>
-#define PB1200_INT_BEGIN DB1200_INT_BEGIN
-#define PB1200_INT_END DB1200_INT_END
-#endif
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- /* This is external interrupt cascade */
- { AU1000_GPIO_7, IRQF_TRIGGER_LOW, 0 },
-};
-
-
-/*
- * Support for External interrupts on the Pb1200 Development platform.
- */
-
-static void pb1200_cascade_handler(unsigned int irq, struct irq_desc *d)
-{
- unsigned short bisr = bcsr->int_status;
-
- for ( ; bisr; bisr &= bisr - 1)
- generic_handle_irq(PB1200_INT_BEGIN + __ffs(bisr));
-}
-
-/* NOTE: both the enable and mask bits must be cleared, otherwise the
- * CPLD generates tons of spurious interrupts (at least on the DB1200).
- */
-static void pb1200_mask_irq(unsigned int irq_nr)
-{
- bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
- au_sync();
-}
-
-static void pb1200_maskack_irq(unsigned int irq_nr)
-{
- bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->int_status = 1 << (irq_nr - PB1200_INT_BEGIN); /* ack */
- au_sync();
-}
-
-static void pb1200_unmask_irq(unsigned int irq_nr)
-{
- bcsr->intset = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->intset_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
- au_sync();
-}
-
-static struct irq_chip pb1200_cpld_irq_type = {
-#ifdef CONFIG_MIPS_PB1200
- .name = "Pb1200 Ext",
-#endif
-#ifdef CONFIG_MIPS_DB1200
- .name = "Db1200 Ext",
-#endif
- .mask = pb1200_mask_irq,
- .mask_ack = pb1200_maskack_irq,
- .unmask = pb1200_unmask_irq,
-};
-
-void __init board_init_irq(void)
-{
- unsigned int irq;
-
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-
-#ifdef CONFIG_MIPS_PB1200
- /* We have a problem with CPLD rev 3. */
- if (((bcsr->whoami & BCSR_WHOAMI_CPLD) >> 4) <= 3) {
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
- printk(KERN_ERR "updated to latest revision. This software will\n");
- printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- panic("Game over. Your score is 0.");
- }
-#endif
- /* mask & disable & ack all */
- bcsr->intclr_mask = 0xffff;
- bcsr->intclr = 0xffff;
- bcsr->int_status = 0xffff;
- au_sync();
-
- for (irq = PB1200_INT_BEGIN; irq <= PB1200_INT_END; irq++)
- set_irq_chip_and_handler_name(irq, &pb1200_cpld_irq_type,
- handle_level_irq, "level");
-
- set_irq_chained_handler(AU1000_GPIO_7, pb1200_cascade_handler);
-}
diff --git a/arch/mips/alchemy/devboards/pb1200/platform.c b/arch/mips/alchemy/devboards/pb1200/platform.c
index b93dff4a678..3ef2dceeb79 100644
--- a/arch/mips/alchemy/devboards/pb1200/platform.c
+++ b/arch/mips/alchemy/devboards/pb1200/platform.c
@@ -26,27 +26,30 @@
#include <asm/mach-au1x00/au1xxx.h>
#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
static int mmc_activity;
static void pb1200mmc0_set_power(void *mmc_host, int state)
{
if (state)
- bcsr->board |= BCSR_BOARD_SD0PWR;
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
else
- bcsr->board &= ~BCSR_BOARD_SD0PWR;
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
- au_sync_delay(1);
+ msleep(1);
}
static int pb1200mmc0_card_readonly(void *mmc_host)
{
- return (bcsr->status & BCSR_STATUS_SD0WP) ? 1 : 0;
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
}
static int pb1200mmc0_card_inserted(void *mmc_host)
{
- return (bcsr->sig_status & BCSR_INT_SD0INSERT) ? 1 : 0;
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
}
static void pb1200_mmcled_set(struct led_classdev *led,
@@ -54,10 +57,10 @@ static void pb1200_mmcled_set(struct led_classdev *led,
{
if (brightness != LED_OFF) {
if (++mmc_activity == 1)
- bcsr->disk_leds &= ~(1 << 8);
+ bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
} else {
if (--mmc_activity == 0)
- bcsr->disk_leds |= (1 << 8);
+ bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
}
}
@@ -65,27 +68,25 @@ static struct led_classdev pb1200mmc_led = {
.brightness_set = pb1200_mmcled_set,
};
-#ifndef CONFIG_MIPS_DB1200
static void pb1200mmc1_set_power(void *mmc_host, int state)
{
if (state)
- bcsr->board |= BCSR_BOARD_SD1PWR;
+ bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
else
- bcsr->board &= ~BCSR_BOARD_SD1PWR;
+ bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
- au_sync_delay(1);
+ msleep(1);
}
static int pb1200mmc1_card_readonly(void *mmc_host)
{
- return (bcsr->status & BCSR_STATUS_SD1WP) ? 1 : 0;
+ return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
}
static int pb1200mmc1_card_inserted(void *mmc_host)
{
- return (bcsr->sig_status & BCSR_INT_SD1INSERT) ? 1 : 0;
+ return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
}
-#endif
const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
[0] = {
@@ -95,7 +96,6 @@ const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
.cd_setup = NULL, /* use poll-timer in driver */
.led = &pb1200mmc_led,
},
-#ifndef CONFIG_MIPS_DB1200
[1] = {
.set_power = pb1200mmc1_set_power,
.card_inserted = pb1200mmc1_card_inserted,
@@ -103,7 +103,6 @@ const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
.cd_setup = NULL, /* use poll-timer in driver */
.led = &pb1200mmc_led,
},
-#endif
};
static struct resource ide_resources[] = {
@@ -169,8 +168,36 @@ static struct platform_device *board_platform_devices[] __initdata = {
static int __init board_register_devices(void)
{
+ int swapped;
+
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+ PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR,
+ PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_IO_PHYS_ADDR,
+ PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ PB1200_PC0_INT,
+ PB1200_PC0_INSERT_INT,
+ /*PB1200_PC0_STSCHG_INT*/0,
+ PB1200_PC0_EJECT_INT,
+ 0);
+
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ PB1200_PC1_INT,
+ PB1200_PC1_INSERT_INT,
+ /*PB1200_PC1_STSCHG_INT*/0,
+ PB1200_PC1_EJECT_INT,
+ 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
+
return platform_add_devices(board_platform_devices,
ARRAY_SIZE(board_platform_devices));
}
-
-arch_initcall(board_register_devices);
+device_initcall(board_register_devices);
diff --git a/arch/mips/alchemy/devboards/pb1500/Makefile b/arch/mips/alchemy/devboards/pb1500/Makefile
index 173b419a747..e83b151b5b6 100644
--- a/arch/mips/alchemy/devboards/pb1500/Makefile
+++ b/arch/mips/alchemy/devboards/pb1500/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor Pb1500 board.
#
-obj-y := board_setup.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1500/board_setup.c b/arch/mips/alchemy/devboards/pb1500/board_setup.c
index d7a56569e7e..fa9770ac358 100644
--- a/arch/mips/alchemy/devboards/pb1500/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1500/board_setup.c
@@ -29,22 +29,14 @@
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1500.h>
+#include <asm/mach-db1x00/bcsr.h>
#include <prom.h>
char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT370 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
- { AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
+ [12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - HPT370 */
+ [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
};
@@ -55,35 +47,16 @@ const char *get_system_type(void)
void board_reset(void)
{
- /* Hit BCSR.RST_VDDI[SOFT_RESET] */
- au_writel(0x00000000, PB1500_RST_VDDI);
-}
-
-void __init board_init_irq(void)
-{
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
+ bcsr_write(BCSR_SYSTEM, 0);
}
void __init board_setup(void)
{
u32 pin_func;
u32 sys_freqctrl, sys_clksrc;
- char *argptr;
-
- argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
-#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
- /* au1000 does not support vra, au1500 and au1100 do */
- strcat(argptr, " au1000_audio=vra");
- argptr = prom_getcmdline();
-#endif
+ bcsr_init(DB1000_BCSR_PHYS_ADDR,
+ DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
sys_clksrc = sys_freqctrl = pin_func = 0;
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
@@ -163,3 +136,18 @@ void __init board_setup(void)
au_sync();
}
}
+
+static int __init pb1500_init_irq(void)
+{
+ set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW); /* CD0# */
+ set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW); /* CARD0 */
+ set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+ set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+ set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+ return 0;
+}
+arch_initcall(pb1500_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1500/platform.c b/arch/mips/alchemy/devboards/pb1500/platform.c
new file mode 100644
index 00000000000..d443bc7aa76
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1500/platform.c
@@ -0,0 +1,49 @@
+/*
+ * Pb1500 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
+
+static int __init pb1500_dev_init(void)
+{
+ int swapped;
+
+ /* PCMCIA. single socket, identical to Pb1500 */
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+ PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR,
+ PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_IO_PHYS_ADDR,
+ PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1500_GPIO11_INT, /* card */
+ AU1500_GPIO9_INT, /* insert */
+ /*AU1500_GPIO10_INT*/0, /* stschg */
+ 0, /* eject */
+ 0); /* id */
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
+ db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+
+ return 0;
+}
+device_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550/Makefile b/arch/mips/alchemy/devboards/pb1550/Makefile
index cff95bcdb2c..9661b6ec5dd 100644
--- a/arch/mips/alchemy/devboards/pb1550/Makefile
+++ b/arch/mips/alchemy/devboards/pb1550/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor Pb1550 board.
#
-obj-y := board_setup.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1550/board_setup.c b/arch/mips/alchemy/devboards/pb1550/board_setup.c
index b6e9e7d247a..1e8fb3ddd72 100644
--- a/arch/mips/alchemy/devboards/pb1550/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1550/board_setup.c
@@ -32,18 +32,15 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1550.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-au1x00/gpio.h>
#include <prom.h>
char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 },
- { AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 },
+ [12] = { -1, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD, AU1550_PCI_INTA }, /* IDSEL 12 - PCI slot 2 (left) */
+ [13] = { -1, AU1550_PCI_INTA, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD }, /* IDSEL 13 - PCI slot 1 (right) */
};
const char *get_system_type(void)
@@ -53,28 +50,17 @@ const char *get_system_type(void)
void board_reset(void)
{
- /* Hit BCSR.SYSTEM[RESET] */
- au_writew(au_readw(0xAF00001C) & ~BCSR_SYSTEM_RESET, 0xAF00001C);
-}
-
-void __init board_init_irq(void)
-{
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
+ bcsr_write(BCSR_SYSTEM, 0);
}
void __init board_setup(void)
{
u32 pin_func;
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- char *argptr;
- argptr = prom_getcmdline();
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
+ bcsr_init(PB1550_BCSR_PHYS_ADDR,
+ PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
+
+ alchemy_gpio2_enable();
/*
* Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
@@ -85,8 +71,21 @@ void __init board_setup(void)
pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
au_writel(pin_func, SYS_PINFUNC);
- au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
- au_sync();
+ bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */
printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
}
+
+static int __init pb1550_init_irq(void)
+{
+ set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
+
+ /* enable both PCMCIA card irqs in the shared line */
+ alchemy_gpio2_enable_int(201);
+ alchemy_gpio2_enable_int(202);
+
+ return 0;
+}
+arch_initcall(pb1550_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1550/platform.c b/arch/mips/alchemy/devboards/pb1550/platform.c
new file mode 100644
index 00000000000..d7150d0f49c
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1550/platform.c
@@ -0,0 +1,69 @@
+/*
+ * Pb1550 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-pb1x00/pb1550.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
+
+static int __init pb1550_dev_init(void)
+{
+ int swapped;
+
+ /* Pb1550, like all others, also has statuschange irqs; however they're
+ * wired up on one of the Au1550's shared GPIO201_205 line, which also
+ * services the PCMCIA card interrupts. So we ignore statuschange and
+ * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
+ * drivers are used to shared irqs and b) statuschange isn't really use-
+ * ful anyway.
+ */
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+ PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR,
+ PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ PCMCIA_IO_PHYS_ADDR,
+ PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
+ AU1550_GPIO201_205_INT,
+ AU1550_GPIO0_INT,
+ 0,
+ 0,
+ 0);
+
+ db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+ PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+ PCMCIA_MEM_PHYS_ADDR + 0x008000000,
+ PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
+ PCMCIA_IO_PHYS_ADDR + 0x008000000,
+ PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
+ AU1550_GPIO201_205_INT,
+ AU1550_GPIO1_INT,
+ 0,
+ 0,
+ 1);
+
+ swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
+ db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
+
+ return 0;
+}
+device_initcall(pb1550_dev_init);
diff --git a/arch/mips/alchemy/devboards/platform.c b/arch/mips/alchemy/devboards/platform.c
new file mode 100644
index 00000000000..49a4b3244d8
--- /dev/null
+++ b/arch/mips/alchemy/devboards/platform.c
@@ -0,0 +1,222 @@
+/*
+ * devoard misc stuff.
+ */
+
+#include <linux/init.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/physmap.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+
+#include <asm/reboot.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+static void db1x_power_off(void)
+{
+ bcsr_write(BCSR_RESETS, 0);
+ bcsr_write(BCSR_SYSTEM, BCSR_SYSTEM_PWROFF | BCSR_SYSTEM_RESET);
+}
+
+static void db1x_reset(char *c)
+{
+ bcsr_write(BCSR_RESETS, 0);
+ bcsr_write(BCSR_SYSTEM, 0);
+}
+
+static int __init db1x_poweroff_setup(void)
+{
+ if (!pm_power_off)
+ pm_power_off = db1x_power_off;
+ if (!_machine_halt)
+ _machine_halt = db1x_power_off;
+ if (!_machine_restart)
+ _machine_restart = db1x_reset;
+
+ return 0;
+}
+late_initcall(db1x_poweroff_setup);
+
+/* register a pcmcia socket */
+int __init db1x_register_pcmcia_socket(phys_addr_t pcmcia_attr_start,
+ phys_addr_t pcmcia_attr_end,
+ phys_addr_t pcmcia_mem_start,
+ phys_addr_t pcmcia_mem_end,
+ phys_addr_t pcmcia_io_start,
+ phys_addr_t pcmcia_io_end,
+ int card_irq,
+ int cd_irq,
+ int stschg_irq,
+ int eject_irq,
+ int id)
+{
+ int cnt, i, ret;
+ struct resource *sr;
+ struct platform_device *pd;
+
+ cnt = 5;
+ if (eject_irq)
+ cnt++;
+ if (stschg_irq)
+ cnt++;
+
+ sr = kzalloc(sizeof(struct resource) * cnt, GFP_KERNEL);
+ if (!sr)
+ return -ENOMEM;
+
+ pd = platform_device_alloc("db1xxx_pcmcia", id);
+ if (!pd) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ sr[0].name = "pcmcia-attr";
+ sr[0].flags = IORESOURCE_MEM;
+ sr[0].start = pcmcia_attr_start;
+ sr[0].end = pcmcia_attr_end;
+
+ sr[1].name = "pcmcia-mem";
+ sr[1].flags = IORESOURCE_MEM;
+ sr[1].start = pcmcia_mem_start;
+ sr[1].end = pcmcia_mem_end;
+
+ sr[2].name = "pcmcia-io";
+ sr[2].flags = IORESOURCE_MEM;
+ sr[2].start = pcmcia_io_start;
+ sr[2].end = pcmcia_io_end;
+
+ sr[3].name = "insert";
+ sr[3].flags = IORESOURCE_IRQ;
+ sr[3].start = sr[3].end = cd_irq;
+
+ sr[4].name = "card";
+ sr[4].flags = IORESOURCE_IRQ;
+ sr[4].start = sr[4].end = card_irq;
+
+ i = 5;
+ if (stschg_irq) {
+ sr[i].name = "stschg";
+ sr[i].flags = IORESOURCE_IRQ;
+ sr[i].start = sr[i].end = stschg_irq;
+ i++;
+ }
+ if (eject_irq) {
+ sr[i].name = "eject";
+ sr[i].flags = IORESOURCE_IRQ;
+ sr[i].start = sr[i].end = eject_irq;
+ }
+
+ pd->resource = sr;
+ pd->num_resources = cnt;
+
+ ret = platform_device_add(pd);
+ if (!ret)
+ return 0;
+
+ platform_device_put(pd);
+out:
+ kfree(sr);
+ return ret;
+}
+
+#define YAMON_SIZE 0x00100000
+#define YAMON_ENV_SIZE 0x00040000
+
+int __init db1x_register_norflash(unsigned long size, int width,
+ int swapped)
+{
+ struct physmap_flash_data *pfd;
+ struct platform_device *pd;
+ struct mtd_partition *parts;
+ struct resource *res;
+ int ret, i;
+
+ if (size < (8 * 1024 * 1024))
+ return -EINVAL;
+
+ ret = -ENOMEM;
+ parts = kzalloc(sizeof(struct mtd_partition) * 5, GFP_KERNEL);
+ if (!parts)
+ goto out;
+
+ res = kzalloc(sizeof(struct resource), GFP_KERNEL);
+ if (!res)
+ goto out1;
+
+ pfd = kzalloc(sizeof(struct physmap_flash_data), GFP_KERNEL);
+ if (!pfd)
+ goto out2;
+
+ pd = platform_device_alloc("physmap-flash", 0);
+ if (!pd)
+ goto out3;
+
+ /* NOR flash ends at 0x20000000, regardless of size */
+ res->start = 0x20000000 - size;
+ res->end = 0x20000000 - 1;
+ res->flags = IORESOURCE_MEM;
+
+ /* partition setup. Most Develboards have a switch which allows
+ * to swap the physical locations of the 2 NOR flash banks.
+ */
+ i = 0;
+ if (!swapped) {
+ /* first NOR chip */
+ parts[i].offset = 0;
+ parts[i].name = "User FS";
+ parts[i].size = size / 2;
+ i++;
+ }
+
+ parts[i].offset = MTDPART_OFS_APPEND;
+ parts[i].name = "User FS 2";
+ parts[i].size = (size / 2) - (0x20000000 - 0x1fc00000);
+ i++;
+
+ parts[i].offset = MTDPART_OFS_APPEND;
+ parts[i].name = "YAMON";
+ parts[i].size = YAMON_SIZE;
+ parts[i].mask_flags = MTD_WRITEABLE;
+ i++;
+
+ parts[i].offset = MTDPART_OFS_APPEND;
+ parts[i].name = "raw kernel";
+ parts[i].size = 0x00400000 - YAMON_SIZE - YAMON_ENV_SIZE;
+ i++;
+
+ parts[i].offset = MTDPART_OFS_APPEND;
+ parts[i].name = "YAMON Env";
+ parts[i].size = YAMON_ENV_SIZE;
+ parts[i].mask_flags = MTD_WRITEABLE;
+ i++;
+
+ if (swapped) {
+ parts[i].offset = MTDPART_OFS_APPEND;
+ parts[i].name = "User FS";
+ parts[i].size = size / 2;
+ i++;
+ }
+
+ pfd->width = width;
+ pfd->parts = parts;
+ pfd->nr_parts = 5;
+
+ pd->dev.platform_data = pfd;
+ pd->resource = res;
+ pd->num_resources = 1;
+
+ ret = platform_device_add(pd);
+ if (!ret)
+ return ret;
+
+ platform_device_put(pd);
+out3:
+ kfree(pfd);
+out2:
+ kfree(res);
+out1:
+ kfree(parts);
+out:
+ return ret;
+}
diff --git a/arch/mips/alchemy/devboards/platform.h b/arch/mips/alchemy/devboards/platform.h
new file mode 100644
index 00000000000..5ac055d2cda
--- /dev/null
+++ b/arch/mips/alchemy/devboards/platform.h
@@ -0,0 +1,21 @@
+#ifndef _DEVBOARD_PLATFORM_H_
+#define _DEVBOARD_PLATFORM_H_
+
+#include <linux/init.h>
+
+int __init db1x_register_pcmcia_socket(phys_addr_t pcmcia_attr_start,
+ phys_addr_t pcmcia_attr_len,
+ phys_addr_t pcmcia_mem_start,
+ phys_addr_t pcmcia_mem_end,
+ phys_addr_t pcmcia_io_start,
+ phys_addr_t pcmcia_io_end,
+ int card_irq,
+ int cd_irq,
+ int stschg_irq,
+ int eject_irq,
+ int id);
+
+int __init db1x_register_norflash(unsigned long size, int width,
+ int swapped);
+
+#endif
diff --git a/arch/mips/alchemy/devboards/pm.c b/arch/mips/alchemy/devboards/pm.c
index 632f9862a0f..4bbd3133e45 100644
--- a/arch/mips/alchemy/devboards/pm.c
+++ b/arch/mips/alchemy/devboards/pm.c
@@ -10,6 +10,7 @@
#include <linux/sysfs.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/gpio.h>
+#include <asm/mach-db1x00/bcsr.h>
/*
* Generic suspend userspace interface for Alchemy development boards.
@@ -26,6 +27,20 @@ static unsigned long db1x_pm_last_wakesrc;
static int db1x_pm_enter(suspend_state_t state)
{
+ unsigned short bcsrs[16];
+ int i, j, hasint;
+
+ /* save CPLD regs */
+ hasint = bcsr_read(BCSR_WHOAMI);
+ hasint = BCSR_WHOAMI_BOARD(hasint) >= BCSR_WHOAMI_DB1200;
+ j = (hasint) ? BCSR_MASKSET : BCSR_SYSTEM;
+
+ for (i = BCSR_STATUS; i <= j; i++)
+ bcsrs[i] = bcsr_read(i);
+
+ /* shut off hexleds */
+ bcsr_write(BCSR_HEXCLEAR, 3);
+
/* enable GPIO based wakeup */
alchemy_gpio1_input_enable();
@@ -52,6 +67,23 @@ static int db1x_pm_enter(suspend_state_t state)
/* ...and now the sandman can come! */
au_sleep();
+
+ /* restore CPLD regs */
+ for (i = BCSR_STATUS; i <= BCSR_SYSTEM; i++)
+ bcsr_write(i, bcsrs[i]);
+
+ /* restore CPLD int registers */
+ if (hasint) {
+ bcsr_write(BCSR_INTCLR, 0xffff);
+ bcsr_write(BCSR_MASKCLR, 0xffff);
+ bcsr_write(BCSR_INTSTAT, 0xffff);
+ bcsr_write(BCSR_INTSET, bcsrs[BCSR_INTSET]);
+ bcsr_write(BCSR_MASKSET, bcsrs[BCSR_MASKSET]);
+ }
+
+ /* light up hexleds */
+ bcsr_write(BCSR_HEXCLEAR, 0);
+
return 0;
}
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index 0042bd6b1d7..b30df5c97ad 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -60,3 +60,8 @@ void __init prom_init(void)
strict_strtoul(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
+
+void prom_putchar(unsigned char c)
+{
+ alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+}
diff --git a/arch/mips/alchemy/mtx-1/Makefile b/arch/mips/alchemy/mtx-1/Makefile
index 7c67b3d33be..4a53815b3c6 100644
--- a/arch/mips/alchemy/mtx-1/Makefile
+++ b/arch/mips/alchemy/mtx-1/Makefile
@@ -6,7 +6,7 @@
# Makefile for 4G Systems MTX-1 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := init.o board_setup.o
obj-y := platform.o
EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
index 45b61c9b82b..a9f0336e1f1 100644
--- a/arch/mips/alchemy/mtx-1/board_setup.c
+++ b/arch/mips/alchemy/mtx-1/board_setup.c
@@ -30,32 +30,43 @@
#include <linux/gpio.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+#include <asm/reboot.h>
#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
+char irq_tab_alchemy[][5] __initdata = {
+ [0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
+ [1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
+ [2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
+ [3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
+ [4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
+ [5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
+ [6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
+ [7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
+};
+
extern int (*board_pci_idsel)(unsigned int devsel, int assert);
int mtx1_pci_idsel(unsigned int devsel, int assert);
-void board_reset(void)
+static void mtx1_reset(char *c)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
au_writel(0x00000000, 0xAE00001C);
}
-void __init board_setup(void)
+static void mtx1_power_off(void)
{
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- char *argptr;
- argptr = prom_getcmdline();
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
+ printk(KERN_ALERT "It's now safe to remove power\n");
+ while (1)
+ asm volatile (".set mips3 ; wait ; .set mips1");
+}
+void __init board_setup(void)
+{
alchemy_gpio2_enable();
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
@@ -86,6 +97,10 @@ void __init board_setup(void)
alchemy_gpio_direction_output(211, 1); /* green on */
alchemy_gpio_direction_output(212, 0); /* red off */
+ pm_power_off = mtx1_power_off;
+ _machine_halt = mtx1_power_off;
+ _machine_restart = mtx1_reset;
+
printk(KERN_INFO "4G Systems MTX-1 Board\n");
}
@@ -109,3 +124,15 @@ mtx1_pci_idsel(unsigned int devsel, int assert)
au_sync_udelay(1);
return 1;
}
+
+static int __init mtx1_init_irq(void)
+{
+ set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+ set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+ return 0;
+}
+arch_initcall(mtx1_init_irq);
diff --git a/arch/mips/alchemy/mtx-1/init.c b/arch/mips/alchemy/mtx-1/init.c
index 5e871c8d9e9..f8d25575fa0 100644
--- a/arch/mips/alchemy/mtx-1/init.c
+++ b/arch/mips/alchemy/mtx-1/init.c
@@ -32,6 +32,7 @@
#include <linux/init.h>
#include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
@@ -58,3 +59,8 @@ void __init prom_init(void)
strict_strtoul(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
+
+void prom_putchar(unsigned char c)
+{
+ alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+}
diff --git a/arch/mips/alchemy/mtx-1/irqmap.c b/arch/mips/alchemy/mtx-1/irqmap.c
deleted file mode 100644
index f1ab12ab343..00000000000
--- a/arch/mips/alchemy/mtx-1/irqmap.c
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <asm/mach-au1x00/au1000.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [0] = { -1, INTA, INTA, INTX, INTX }, /* IDSEL 00 - AdapterA-Slot0 (top) */
- [1] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
- [2] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 02 - AdapterB-Slot0 (top) */
- [3] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
- [4] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 04 - AdapterC-Slot0 (top) */
- [5] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
- [6] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 06 - AdapterD-Slot0 (top) */
- [7] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
- { AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
-};
-
-
-void __init board_init_irq(void)
-{
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
diff --git a/arch/mips/alchemy/xxs1500/Makefile b/arch/mips/alchemy/xxs1500/Makefile
index db3c526f64d..4dc81d794cb 100644
--- a/arch/mips/alchemy/xxs1500/Makefile
+++ b/arch/mips/alchemy/xxs1500/Makefile
@@ -5,4 +5,6 @@
# Makefile for MyCable XXS1500 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := init.o board_setup.o platform.o
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index 4de2d48caed..47b42927607 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -25,31 +25,35 @@
#include <linux/gpio.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
#include <linux/delay.h>
+#include <linux/pm.h>
+#include <asm/reboot.h>
#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
-void board_reset(void)
+static void xxs1500_reset(char *c)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
au_writel(0x00000000, 0xAE00001C);
}
+static void xxs1500_power_off(void)
+{
+ printk(KERN_ALERT "It's now safe to remove power\n");
+ while (1)
+ asm volatile (".set mips3 ; wait ; .set mips1");
+}
+
void __init board_setup(void)
{
u32 pin_func;
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- char *argptr;
- argptr = prom_getcmdline();
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
+ pm_power_off = xxs1500_power_off;
+ _machine_halt = xxs1500_power_off;
+ _machine_restart = xxs1500_reset;
alchemy_gpio1_input_enable();
alchemy_gpio2_enable();
@@ -68,22 +72,6 @@ void __init board_setup(void)
/* Enable DTR = USB power up */
au_writel(0x01, UART3_ADDR + UART_MCR); /* UART_MCR_DTR is 0x01??? */
-#ifdef CONFIG_PCMCIA_XXS1500
- /* GPIO 0, 1, and 4 are inputs */
- alchemy_gpio_direction_input(0);
- alchemy_gpio_direction_input(1);
- alchemy_gpio_direction_input(4);
-
- /* GPIO2 208/9/10/11 are inputs */
- alchemy_gpio_direction_input(208);
- alchemy_gpio_direction_input(209);
- alchemy_gpio_direction_input(210);
- alchemy_gpio_direction_input(211);
-
- /* Turn off power */
- alchemy_gpio_direction_output(214, 0);
-#endif
-
#ifdef CONFIG_PCI
#if defined(__MIPSEB__)
au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
@@ -92,3 +80,23 @@ void __init board_setup(void)
#endif
#endif
}
+
+static int __init xxs1500_init_irq(void)
+{
+ set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+ set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO207_INT, IRQF_TRIGGER_LOW);
+
+ set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW);
+ set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* CF irq */
+ set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW);
+
+ return 0;
+}
+arch_initcall(xxs1500_init_irq);
diff --git a/arch/mips/alchemy/xxs1500/init.c b/arch/mips/alchemy/xxs1500/init.c
index 456fa142c09..15125c2fda7 100644
--- a/arch/mips/alchemy/xxs1500/init.c
+++ b/arch/mips/alchemy/xxs1500/init.c
@@ -30,6 +30,7 @@
#include <linux/kernel.h>
#include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
@@ -56,3 +57,8 @@ void __init prom_init(void)
strict_strtoul(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
+
+void prom_putchar(unsigned char c)
+{
+ alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+}
diff --git a/arch/mips/alchemy/xxs1500/irqmap.c b/arch/mips/alchemy/xxs1500/irqmap.c
deleted file mode 100644
index 0f0f3012e5f..00000000000
--- a/arch/mips/alchemy/xxs1500/irqmap.c
+++ /dev/null
@@ -1,52 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <asm/mach-au1x00/au1000.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
- { AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
- { AU1500_GPIO_207, IRQF_TRIGGER_LOW, 0 },
-
- { AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 },
- { AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 },
- { AU1000_GPIO_2, IRQF_TRIGGER_LOW, 0 },
- { AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 },
- { AU1000_GPIO_4, IRQF_TRIGGER_LOW, 0 }, /* CF interrupt */
- { AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 },
-};
-
-void __init board_init_irq(void)
-{
- au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
diff --git a/arch/mips/alchemy/xxs1500/platform.c b/arch/mips/alchemy/xxs1500/platform.c
new file mode 100644
index 00000000000..e87c45cde61
--- /dev/null
+++ b/arch/mips/alchemy/xxs1500/platform.c
@@ -0,0 +1,63 @@
+/*
+ * XXS1500 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-au1x00/au1000.h>
+
+static struct resource xxs1500_pcmcia_res[] = {
+ {
+ .name = "pcmcia-io",
+ .flags = IORESOURCE_MEM,
+ .start = PCMCIA_IO_PHYS_ADDR,
+ .end = PCMCIA_IO_PHYS_ADDR + 0x000400000 - 1,
+ },
+ {
+ .name = "pcmcia-attr",
+ .flags = IORESOURCE_MEM,
+ .start = PCMCIA_ATTR_PHYS_ADDR,
+ .end = PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+ },
+ {
+ .name = "pcmcia-mem",
+ .flags = IORESOURCE_MEM,
+ .start = PCMCIA_MEM_PHYS_ADDR,
+ .end = PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+ },
+};
+
+static struct platform_device xxs1500_pcmcia_dev = {
+ .name = "xxs1500_pcmcia",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(xxs1500_pcmcia_res),
+ .resource = xxs1500_pcmcia_res,
+};
+
+static struct platform_device *xxs1500_devs[] __initdata = {
+ &xxs1500_pcmcia_dev,
+};
+
+static int __init xxs1500_dev_init(void)
+{
+ return platform_add_devices(xxs1500_devs,
+ ARRAY_SIZE(xxs1500_devs));
+}
+device_initcall(xxs1500_dev_init);