diff options
Diffstat (limited to 'arch/mips/au1000/pb1100/board_setup.c')
-rw-r--r-- | arch/mips/au1000/pb1100/board_setup.c | 116 |
1 files changed, 116 insertions, 0 deletions
diff --git a/arch/mips/au1000/pb1100/board_setup.c b/arch/mips/au1000/pb1100/board_setup.c new file mode 100644 index 00000000000..13c2f6ca7e3 --- /dev/null +++ b/arch/mips/au1000/pb1100/board_setup.c @@ -0,0 +1,116 @@ +/* + * Copyright 2002 MontaVista Software Inc. + * Author: MontaVista Software, Inc. + * ppopov@mvista.com or source@mvista.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include <linux/config.h> +#include <linux/init.h> +#include <linux/sched.h> +#include <linux/ioport.h> +#include <linux/mm.h> +#include <linux/console.h> +#include <linux/delay.h> + +#include <asm/cpu.h> +#include <asm/bootinfo.h> +#include <asm/irq.h> +#include <asm/mipsregs.h> +#include <asm/reboot.h> +#include <asm/pgtable.h> +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-pb1x00/pb1100.h> + +void board_reset (void) +{ + /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */ + au_writel(0x00000000, 0xAE00001C); +} + +void __init board_setup(void) +{ + u32 pin_func; + u32 sys_freqctrl, sys_clksrc; + + // set AUX clock to 12MHz * 8 = 96 MHz + au_writel(8, SYS_AUXPLL); + au_writel(0, SYS_PININPUTEN); + udelay(100); + +#if defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE) + // configure pins GPIO[14:9] as GPIO + pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80); + + /* zero and disable FREQ2 */ + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* zero and disable USBH/USBD/IrDA clock */ + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~0x0000001F; + au_writel(sys_clksrc, SYS_CLKSRC); + + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~0x0000001F; + + // FREQ2 = aux/2 = 48 MHz + sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20)); + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* + * Route 48MHz FREQ2 into USBH/USBD/IrDA + */ + sys_clksrc |= ((4<<2) | (0<<1) | 0 ); + au_writel(sys_clksrc, SYS_CLKSRC); + + /* setup the static bus controller */ + au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */ + au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */ + au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */ + + // get USB Functionality pin state (device vs host drive pins) + pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000); +#ifndef CONFIG_AU1X00_USB_DEVICE + // 2nd USB port is USB host + pin_func |= 0x8000; +#endif + au_writel(pin_func, SYS_PINFUNC); +#endif // defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE) + + /* Enable sys bus clock divider when IDLE state or no bus activity. */ + au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL); + + // Enable the RTC if not already enabled + if (!(readb(0xac000028) & 0x20)) { + writeb(readb(0xac000028) | 0x20, 0xac000028); + au_sync(); + } + // Put the clock in BCD mode + if (readb(0xac00002C) & 0x4) { /* reg B */ + writeb(readb(0xac00002c) & ~0x4, 0xac00002c); + au_sync(); + } +} |