summaryrefslogtreecommitdiffstats
path: root/arch/mips/au1000/pb1500/board_setup.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/mips/au1000/pb1500/board_setup.c')
-rw-r--r--arch/mips/au1000/pb1500/board_setup.c46
1 files changed, 21 insertions, 25 deletions
diff --git a/arch/mips/au1000/pb1500/board_setup.c b/arch/mips/au1000/pb1500/board_setup.c
index 24c652e8ec4..035771c6e5b 100644
--- a/arch/mips/au1000/pb1500/board_setup.c
+++ b/arch/mips/au1000/pb1500/board_setup.c
@@ -1,7 +1,6 @@
/*
- * Copyright 2000 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
@@ -32,8 +31,8 @@
void board_reset(void)
{
- /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
- au_writel(0x00000000, 0xAE00001C);
+ /* Hit BCSR.RST_VDDI[SOFT_RESET] */
+ au_writel(0x00000000, PB1500_RST_VDDI);
}
void __init board_setup(void)
@@ -42,7 +41,7 @@ void __init board_setup(void)
u32 sys_freqctrl, sys_clksrc;
sys_clksrc = sys_freqctrl = pin_func = 0;
- // set AUX clock to 12MHz * 8 = 96 MHz
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PINSTATERD);
udelay(100);
@@ -51,51 +50,48 @@ void __init board_setup(void)
/* GPIO201 is input for PCMCIA card detect */
/* GPIO203 is input for PCMCIA interrupt request */
- au_writel(au_readl(GPIO2_DIR) & (u32)(~((1<<1)|(1<<3))), GPIO2_DIR);
+ au_writel(au_readl(GPIO2_DIR) & ~((1 << 1) | (1 << 3)), GPIO2_DIR);
- /* zero and disable FREQ2 */
+ /* Zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* zero and disable USBH/USBD clocks */
sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~0x00007FE0;
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
au_writel(sys_clksrc, SYS_CLKSRC);
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~0x00007FE0;
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- // FREQ2 = aux/2 = 48 MHz
- sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
+ /* FREQ2 = aux/2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
-#endif
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
au_writel(sys_clksrc, SYS_CLKSRC);
-
- pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
- // 2nd USB port is USB host
- pin_func |= 0x8000;
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host */
+ pin_func |= SYS_PF_USB;
au_writel(pin_func, SYS_PINFUNC);
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
-
#ifdef CONFIG_PCI
- // Setup PCI bus controller
+ /* Setup PCI bus controller */
au_writel(0, Au1500_PCI_CMEM);
au_writel(0x00003fff, Au1500_CFG_BASE);
#if defined(__MIPSEB__)
- au_writel(0xf | (2<<6) | (1<<4), Au1500_PCI_CFG);
+ au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
#else
au_writel(0xf, Au1500_PCI_CFG);
#endif
@@ -112,11 +108,11 @@ void __init board_setup(void)
/* Enable the RTC if not already enabled */
if (!(au_readl(0xac000028) & 0x20)) {
- printk("enabling clock ...\n");
+ printk(KERN_INFO "enabling clock ...\n");
au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
}
/* Put the clock in BCD mode */
- if (au_readl(0xac00002C) & 0x4) { /* reg B */
+ if (au_readl(0xac00002c) & 0x4) { /* reg B */
au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
au_sync();
}