diff options
Diffstat (limited to 'arch/mips/au1000')
| -rw-r--r-- | arch/mips/au1000/common/cputable.c | 36 | ||||
| -rw-r--r-- | arch/mips/au1000/common/setup.c | 13 | ||||
| -rw-r--r-- | arch/mips/au1000/common/time.c | 24 | ||||
| -rw-r--r-- | arch/mips/au1000/xxs1500/board_setup.c | 3 | ||||
| -rw-r--r-- | arch/mips/au1000/xxs1500/irqmap.c | 2 |
5 files changed, 44 insertions, 34 deletions
diff --git a/arch/mips/au1000/common/cputable.c b/arch/mips/au1000/common/cputable.c index d8df5fdb045..5c0d35d6e22 100644 --- a/arch/mips/au1000/common/cputable.c +++ b/arch/mips/au1000/common/cputable.c @@ -22,24 +22,24 @@ struct cpu_spec* cur_cpu_spec[NR_CPUS]; /* With some thought, we can probably use the mask to reduce the * size of the table. */ -struct cpu_spec cpu_specs[] = { - { 0xffffffff, 0x00030100, "Au1000 DA", 1, 0 }, - { 0xffffffff, 0x00030201, "Au1000 HA", 1, 0 }, - { 0xffffffff, 0x00030202, "Au1000 HB", 1, 0 }, - { 0xffffffff, 0x00030203, "Au1000 HC", 1, 1 }, - { 0xffffffff, 0x00030204, "Au1000 HD", 1, 1 }, - { 0xffffffff, 0x01030200, "Au1500 AB", 1, 1 }, - { 0xffffffff, 0x01030201, "Au1500 AC", 0, 1 }, - { 0xffffffff, 0x01030202, "Au1500 AD", 0, 1 }, - { 0xffffffff, 0x02030200, "Au1100 AB", 1, 1 }, - { 0xffffffff, 0x02030201, "Au1100 BA", 1, 1 }, - { 0xffffffff, 0x02030202, "Au1100 BC", 1, 1 }, - { 0xffffffff, 0x02030203, "Au1100 BD", 0, 1 }, - { 0xffffffff, 0x02030204, "Au1100 BE", 0, 1 }, - { 0xffffffff, 0x03030200, "Au1550 AA", 0, 1 }, - { 0xffffffff, 0x04030200, "Au1200 AB", 0, 0 }, - { 0xffffffff, 0x04030201, "Au1200 AC", 1, 0 }, - { 0x00000000, 0x00000000, "Unknown Au1xxx", 1, 0 }, +struct cpu_spec cpu_specs[] = { + { 0xffffffff, 0x00030100, "Au1000 DA", 1, 0, 1 }, + { 0xffffffff, 0x00030201, "Au1000 HA", 1, 0, 1 }, + { 0xffffffff, 0x00030202, "Au1000 HB", 1, 0, 1 }, + { 0xffffffff, 0x00030203, "Au1000 HC", 1, 1, 0 }, + { 0xffffffff, 0x00030204, "Au1000 HD", 1, 1, 0 }, + { 0xffffffff, 0x01030200, "Au1500 AB", 1, 1, 0 }, + { 0xffffffff, 0x01030201, "Au1500 AC", 0, 1, 0 }, + { 0xffffffff, 0x01030202, "Au1500 AD", 0, 1, 0 }, + { 0xffffffff, 0x02030200, "Au1100 AB", 1, 1, 0 }, + { 0xffffffff, 0x02030201, "Au1100 BA", 1, 1, 0 }, + { 0xffffffff, 0x02030202, "Au1100 BC", 1, 1, 0 }, + { 0xffffffff, 0x02030203, "Au1100 BD", 0, 1, 0 }, + { 0xffffffff, 0x02030204, "Au1100 BE", 0, 1, 0 }, + { 0xffffffff, 0x03030200, "Au1550 AA", 0, 1, 0 }, + { 0xffffffff, 0x04030200, "Au1200 AB", 0, 0, 0 }, + { 0xffffffff, 0x04030201, "Au1200 AC", 1, 0, 0 }, + { 0x00000000, 0x00000000, "Unknown Au1xxx", 1, 0, 0 } }; void diff --git a/arch/mips/au1000/common/setup.c b/arch/mips/au1000/common/setup.c index d885e3848ec..9e4ab80caab 100644 --- a/arch/mips/au1000/common/setup.c +++ b/arch/mips/au1000/common/setup.c @@ -57,7 +57,7 @@ void __init plat_mem_setup(void) { struct cpu_spec *sp; char *argptr; - unsigned long prid, cpupll, bclk = 1; + unsigned long prid, cpufreq, bclk = 1; set_cpuspec(); sp = cur_cpu_spec[0]; @@ -65,8 +65,15 @@ void __init plat_mem_setup(void) board_setup(); /* board specific setup */ prid = read_c0_prid(); - cpupll = (au_readl(0xB1900060) & 0x3F) * 12; - printk("(PRId %08lx) @ %ldMHZ\n", prid, cpupll); + if (sp->cpu_pll_wo) +#ifdef CONFIG_SOC_AU1000_FREQUENCY + cpufreq = CONFIG_SOC_AU1000_FREQUENCY / 1000000; +#else + cpufreq = 396; +#endif + else + cpufreq = (au_readl(SYS_CPUPLL) & 0x3F) * 12; + printk(KERN_INFO "(PRID %08lx) @ %ld MHz\n", prid, cpufreq); bclk = sp->cpu_bclk; if (bclk) diff --git a/arch/mips/au1000/common/time.c b/arch/mips/au1000/common/time.c index f113b512d7b..e122bbc6cd8 100644 --- a/arch/mips/au1000/common/time.c +++ b/arch/mips/au1000/common/time.c @@ -209,18 +209,22 @@ unsigned long cal_r4koff(void) while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S); au_writel(0, SYS_TOYWRITE); while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S); + } else + no_au1xxx_32khz = 1; - cpu_speed = (au_readl(SYS_CPUPLL) & 0x0000003f) * - AU1000_SRC_CLK; - } - else { - /* The 32KHz oscillator isn't running, so assume there - * isn't one and grab the processor speed from the PLL. - * NOTE: some old silicon doesn't allow reading the PLL. - */ + /* + * On early Au1000, sys_cpupll was write-only. Since these + * silicon versions of Au1000 are not sold by AMD, we don't bend + * over backwards trying to determine the frequency. + */ + if (cur_cpu_spec[0]->cpu_pll_wo) +#ifdef CONFIG_SOC_AU1000_FREQUENCY + cpu_speed = CONFIG_SOC_AU1000_FREQUENCY; +#else + cpu_speed = 396000000; +#endif + else cpu_speed = (au_readl(SYS_CPUPLL) & 0x0000003f) * AU1000_SRC_CLK; - no_au1xxx_32khz = 1; - } mips_hpt_frequency = cpu_speed; // Equation: Baudrate = CPU / (SD * 2 * CLKDIV * 16) set_au1x00_uart_baud_base(cpu_speed / (2 * ((int)(au_readl(SYS_POWERCTRL)&0x03) + 2) * 16)); diff --git a/arch/mips/au1000/xxs1500/board_setup.c b/arch/mips/au1000/xxs1500/board_setup.c index a9237f41933..b2e413e597a 100644 --- a/arch/mips/au1000/xxs1500/board_setup.c +++ b/arch/mips/au1000/xxs1500/board_setup.c @@ -33,11 +33,10 @@ #include <asm/cpu.h> #include <asm/bootinfo.h> #include <asm/irq.h> -#include <asm/keyboard.h> #include <asm/mipsregs.h> #include <asm/reboot.h> #include <asm/pgtable.h> -#include <asm/au1000.h> +#include <asm/mach-au1x00/au1000.h> void board_reset(void) { diff --git a/arch/mips/au1000/xxs1500/irqmap.c b/arch/mips/au1000/xxs1500/irqmap.c index 389349295d7..a343da13433 100644 --- a/arch/mips/au1000/xxs1500/irqmap.c +++ b/arch/mips/au1000/xxs1500/irqmap.c @@ -45,7 +45,7 @@ #include <asm/io.h> #include <asm/mipsregs.h> #include <asm/system.h> -#include <asm/au1000.h> +#include <asm/mach-au1x00/au1000.h> struct au1xxx_irqmap __initdata au1xxx_irq_map[] = { { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0}, |