diff options
Diffstat (limited to 'arch/mips/ddb5xxx/ddb5074/int-handler.S')
| -rw-r--r-- | arch/mips/ddb5xxx/ddb5074/int-handler.S | 120 |
1 files changed, 0 insertions, 120 deletions
diff --git a/arch/mips/ddb5xxx/ddb5074/int-handler.S b/arch/mips/ddb5xxx/ddb5074/int-handler.S deleted file mode 100644 index a78644150b3..00000000000 --- a/arch/mips/ddb5xxx/ddb5074/int-handler.S +++ /dev/null @@ -1,120 +0,0 @@ -/* - * arch/mips/ddb5074/int-handler.S -- NEC DDB Vrc-5074 interrupt handler - * - * Based on arch/mips/sgi/kernel/indyIRQ.S - * - * Copyright (C) 1996 David S. Miller (dm@engr.sgi.com) - * - * Copyright (C) 2000 Geert Uytterhoeven <geert@sonycom.com> - * Sony Software Development Center Europe (SDCE), Brussels - */ -#include <asm/asm.h> -#include <asm/mipsregs.h> -#include <asm/regdef.h> -#include <asm/stackframe.h> - -/* A lot of complication here is taken away because: - * - * 1) We handle one interrupt and return, sitting in a loop and moving across - * all the pending IRQ bits in the cause register is _NOT_ the answer, the - * common case is one pending IRQ so optimize in that direction. - * - * 2) We need not check against bits in the status register IRQ mask, that - * would make this routine slow as hell. - * - * 3) Linux only thinks in terms of all IRQs on or all IRQs off, nothing in - * between like BSD spl() brain-damage. - * - * Furthermore, the IRQs on the INDY look basically (barring software IRQs - * which we don't use at all) like: - * - * MIPS IRQ Source - * -------- ------ - * 0 Software (ignored) - * 1 Software (ignored) - * 2 Local IRQ level zero - * 3 Local IRQ level one - * 4 8254 Timer zero - * 5 8254 Timer one - * 6 Bus Error - * 7 R4k timer (what we use) - * - * We handle the IRQ according to _our_ priority which is: - * - * Highest ---- R4k Timer - * Local IRQ zero - * Local IRQ one - * Bus Error - * 8254 Timer zero - * Lowest ---- 8254 Timer one - * - * then we just return, if multiple IRQs are pending then we will just take - * another exception, big deal. - */ - - .text - .set noreorder - .set noat - .align 5 - NESTED(ddbIRQ, PT_SIZE, sp) - SAVE_ALL - CLI - .set at - mfc0 s0, CP0_CAUSE # get irq mask - -#if 1 - mfc0 t2,CP0_STATUS # get enabled interrupts - and s0,t2 # isolate allowed ones -#endif - /* First we check for r4k counter/timer IRQ. */ - andi a0, s0, CAUSEF_IP2 # delay slot, check local level zero - beq a0, zero, 1f - andi a0, s0, CAUSEF_IP3 # delay slot, check local level one - - /* Wheee, local level zero interrupt. */ - jal ddb_local0_irqdispatch - move a0, sp # delay slot - - j ret_from_irq - nop # delay slot - -1: - beq a0, zero, 1f - andi a0, s0, CAUSEF_IP6 # delay slot, check bus error - - /* Wheee, local level one interrupt. */ - move a0, sp - jal ddb_local1_irqdispatch - nop - - j ret_from_irq - nop - -1: - beq a0, zero, 1f - nop - - /* Wheee, an asynchronous bus error... */ - move a0, sp - jal ddb_buserror_irq - nop - - j ret_from_irq - nop - -1: - /* Here by mistake? This is possible, what can happen - * is that by the time we take the exception the IRQ - * pin goes low, so just leave if this is the case. - */ - andi a0, s0, (CAUSEF_IP4 | CAUSEF_IP5) - beq a0, zero, 1f - - /* Must be one of the 8254 timers... */ - move a0, sp - jal ddb_8254timer_irq - nop -1: - j ret_from_irq - nop - END(ddbIRQ) |