diff options
Diffstat (limited to 'arch/mips/loongson/lemote-2f/ec_kb3310b.h')
-rw-r--r-- | arch/mips/loongson/lemote-2f/ec_kb3310b.h | 216 |
1 files changed, 108 insertions, 108 deletions
diff --git a/arch/mips/loongson/lemote-2f/ec_kb3310b.h b/arch/mips/loongson/lemote-2f/ec_kb3310b.h index 1595a21b315..5a3f1860d4d 100644 --- a/arch/mips/loongson/lemote-2f/ec_kb3310b.h +++ b/arch/mips/loongson/lemote-2f/ec_kb3310b.h @@ -30,141 +30,141 @@ extern sci_handler yeeloong_report_lid_status; * 2, fill the PORT_LOW as EC register low part. * 3, fill the PORT_DATA as EC register write data or get the data from it. */ -#define EC_IO_PORT_HIGH 0x0381 -#define EC_IO_PORT_LOW 0x0382 -#define EC_IO_PORT_DATA 0x0383 +#define EC_IO_PORT_HIGH 0x0381 +#define EC_IO_PORT_LOW 0x0382 +#define EC_IO_PORT_DATA 0x0383 /* * EC delay time is 500us for register and status access */ -#define EC_REG_DELAY 500 /* unit : us */ -#define EC_CMD_TIMEOUT 0x1000 +#define EC_REG_DELAY 500 /* unit : us */ +#define EC_CMD_TIMEOUT 0x1000 /* * EC access port for SCI communication */ -#define EC_CMD_PORT 0x66 -#define EC_STS_PORT 0x66 -#define EC_DAT_PORT 0x62 -#define CMD_INIT_IDLE_MODE 0xdd -#define CMD_EXIT_IDLE_MODE 0xdf -#define CMD_INIT_RESET_MODE 0xd8 -#define CMD_REBOOT_SYSTEM 0x8c -#define CMD_GET_EVENT_NUM 0x84 -#define CMD_PROGRAM_PIECE 0xda +#define EC_CMD_PORT 0x66 +#define EC_STS_PORT 0x66 +#define EC_DAT_PORT 0x62 +#define CMD_INIT_IDLE_MODE 0xdd +#define CMD_EXIT_IDLE_MODE 0xdf +#define CMD_INIT_RESET_MODE 0xd8 +#define CMD_REBOOT_SYSTEM 0x8c +#define CMD_GET_EVENT_NUM 0x84 +#define CMD_PROGRAM_PIECE 0xda /* temperature & fan registers */ -#define REG_TEMPERATURE_VALUE 0xF458 -#define REG_FAN_AUTO_MAN_SWITCH 0xF459 -#define BIT_FAN_AUTO 0 -#define BIT_FAN_MANUAL 1 -#define REG_FAN_CONTROL 0xF4D2 -#define BIT_FAN_CONTROL_ON (1 << 0) -#define BIT_FAN_CONTROL_OFF (0 << 0) -#define REG_FAN_STATUS 0xF4DA -#define BIT_FAN_STATUS_ON (1 << 0) -#define BIT_FAN_STATUS_OFF (0 << 0) -#define REG_FAN_SPEED_HIGH 0xFE22 -#define REG_FAN_SPEED_LOW 0xFE23 -#define REG_FAN_SPEED_LEVEL 0xF4CC +#define REG_TEMPERATURE_VALUE 0xF458 +#define REG_FAN_AUTO_MAN_SWITCH 0xF459 +#define BIT_FAN_AUTO 0 +#define BIT_FAN_MANUAL 1 +#define REG_FAN_CONTROL 0xF4D2 +#define BIT_FAN_CONTROL_ON (1 << 0) +#define BIT_FAN_CONTROL_OFF (0 << 0) +#define REG_FAN_STATUS 0xF4DA +#define BIT_FAN_STATUS_ON (1 << 0) +#define BIT_FAN_STATUS_OFF (0 << 0) +#define REG_FAN_SPEED_HIGH 0xFE22 +#define REG_FAN_SPEED_LOW 0xFE23 +#define REG_FAN_SPEED_LEVEL 0xF4CC /* fan speed divider */ -#define FAN_SPEED_DIVIDER 480000 /* (60*1000*1000/62.5/2)*/ +#define FAN_SPEED_DIVIDER 480000 /* (60*1000*1000/62.5/2)*/ /* battery registers */ -#define REG_BAT_DESIGN_CAP_HIGH 0xF77D -#define REG_BAT_DESIGN_CAP_LOW 0xF77E -#define REG_BAT_FULLCHG_CAP_HIGH 0xF780 -#define REG_BAT_FULLCHG_CAP_LOW 0xF781 -#define REG_BAT_DESIGN_VOL_HIGH 0xF782 -#define REG_BAT_DESIGN_VOL_LOW 0xF783 -#define REG_BAT_CURRENT_HIGH 0xF784 -#define REG_BAT_CURRENT_LOW 0xF785 -#define REG_BAT_VOLTAGE_HIGH 0xF786 -#define REG_BAT_VOLTAGE_LOW 0xF787 -#define REG_BAT_TEMPERATURE_HIGH 0xF788 -#define REG_BAT_TEMPERATURE_LOW 0xF789 -#define REG_BAT_RELATIVE_CAP_HIGH 0xF492 -#define REG_BAT_RELATIVE_CAP_LOW 0xF493 -#define REG_BAT_VENDOR 0xF4C4 -#define FLAG_BAT_VENDOR_SANYO 0x01 -#define FLAG_BAT_VENDOR_SIMPLO 0x02 -#define REG_BAT_CELL_COUNT 0xF4C6 -#define FLAG_BAT_CELL_3S1P 0x03 -#define FLAG_BAT_CELL_3S2P 0x06 -#define REG_BAT_CHARGE 0xF4A2 -#define FLAG_BAT_CHARGE_DISCHARGE 0x01 -#define FLAG_BAT_CHARGE_CHARGE 0x02 -#define FLAG_BAT_CHARGE_ACPOWER 0x00 -#define REG_BAT_STATUS 0xF4B0 -#define BIT_BAT_STATUS_LOW (1 << 5) -#define BIT_BAT_STATUS_DESTROY (1 << 2) -#define BIT_BAT_STATUS_FULL (1 << 1) -#define BIT_BAT_STATUS_IN (1 << 0) -#define REG_BAT_CHARGE_STATUS 0xF4B1 -#define BIT_BAT_CHARGE_STATUS_OVERTEMP (1 << 2) -#define BIT_BAT_CHARGE_STATUS_PRECHG (1 << 1) -#define REG_BAT_STATE 0xF482 -#define BIT_BAT_STATE_CHARGING (1 << 1) -#define BIT_BAT_STATE_DISCHARGING (1 << 0) -#define REG_BAT_POWER 0xF440 -#define BIT_BAT_POWER_S3 (1 << 2) -#define BIT_BAT_POWER_ON (1 << 1) -#define BIT_BAT_POWER_ACIN (1 << 0) +#define REG_BAT_DESIGN_CAP_HIGH 0xF77D +#define REG_BAT_DESIGN_CAP_LOW 0xF77E +#define REG_BAT_FULLCHG_CAP_HIGH 0xF780 +#define REG_BAT_FULLCHG_CAP_LOW 0xF781 +#define REG_BAT_DESIGN_VOL_HIGH 0xF782 +#define REG_BAT_DESIGN_VOL_LOW 0xF783 +#define REG_BAT_CURRENT_HIGH 0xF784 +#define REG_BAT_CURRENT_LOW 0xF785 +#define REG_BAT_VOLTAGE_HIGH 0xF786 +#define REG_BAT_VOLTAGE_LOW 0xF787 +#define REG_BAT_TEMPERATURE_HIGH 0xF788 +#define REG_BAT_TEMPERATURE_LOW 0xF789 +#define REG_BAT_RELATIVE_CAP_HIGH 0xF492 +#define REG_BAT_RELATIVE_CAP_LOW 0xF493 +#define REG_BAT_VENDOR 0xF4C4 +#define FLAG_BAT_VENDOR_SANYO 0x01 +#define FLAG_BAT_VENDOR_SIMPLO 0x02 +#define REG_BAT_CELL_COUNT 0xF4C6 +#define FLAG_BAT_CELL_3S1P 0x03 +#define FLAG_BAT_CELL_3S2P 0x06 +#define REG_BAT_CHARGE 0xF4A2 +#define FLAG_BAT_CHARGE_DISCHARGE 0x01 +#define FLAG_BAT_CHARGE_CHARGE 0x02 +#define FLAG_BAT_CHARGE_ACPOWER 0x00 +#define REG_BAT_STATUS 0xF4B0 +#define BIT_BAT_STATUS_LOW (1 << 5) +#define BIT_BAT_STATUS_DESTROY (1 << 2) +#define BIT_BAT_STATUS_FULL (1 << 1) +#define BIT_BAT_STATUS_IN (1 << 0) +#define REG_BAT_CHARGE_STATUS 0xF4B1 +#define BIT_BAT_CHARGE_STATUS_OVERTEMP (1 << 2) +#define BIT_BAT_CHARGE_STATUS_PRECHG (1 << 1) +#define REG_BAT_STATE 0xF482 +#define BIT_BAT_STATE_CHARGING (1 << 1) +#define BIT_BAT_STATE_DISCHARGING (1 << 0) +#define REG_BAT_POWER 0xF440 +#define BIT_BAT_POWER_S3 (1 << 2) +#define BIT_BAT_POWER_ON (1 << 1) +#define BIT_BAT_POWER_ACIN (1 << 0) /* other registers */ /* Audio: rd/wr */ -#define REG_AUDIO_VOLUME 0xF46C -#define REG_AUDIO_MUTE 0xF4E7 -#define REG_AUDIO_BEEP 0xF4D0 +#define REG_AUDIO_VOLUME 0xF46C +#define REG_AUDIO_MUTE 0xF4E7 +#define REG_AUDIO_BEEP 0xF4D0 /* USB port power or not: rd/wr */ -#define REG_USB0_FLAG 0xF461 -#define REG_USB1_FLAG 0xF462 -#define REG_USB2_FLAG 0xF463 -#define BIT_USB_FLAG_ON 1 -#define BIT_USB_FLAG_OFF 0 +#define REG_USB0_FLAG 0xF461 +#define REG_USB1_FLAG 0xF462 +#define REG_USB2_FLAG 0xF463 +#define BIT_USB_FLAG_ON 1 +#define BIT_USB_FLAG_OFF 0 /* LID */ -#define REG_LID_DETECT 0xF4BD -#define BIT_LID_DETECT_ON 1 -#define BIT_LID_DETECT_OFF 0 +#define REG_LID_DETECT 0xF4BD +#define BIT_LID_DETECT_ON 1 +#define BIT_LID_DETECT_OFF 0 /* CRT */ -#define REG_CRT_DETECT 0xF4AD -#define BIT_CRT_DETECT_PLUG 1 -#define BIT_CRT_DETECT_UNPLUG 0 +#define REG_CRT_DETECT 0xF4AD +#define BIT_CRT_DETECT_PLUG 1 +#define BIT_CRT_DETECT_UNPLUG 0 /* LCD backlight brightness adjust: 9 levels */ -#define REG_DISPLAY_BRIGHTNESS 0xF4F5 +#define REG_DISPLAY_BRIGHTNESS 0xF4F5 /* Black screen Status */ -#define BIT_DISPLAY_LCD_ON 1 -#define BIT_DISPLAY_LCD_OFF 0 +#define BIT_DISPLAY_LCD_ON 1 +#define BIT_DISPLAY_LCD_OFF 0 /* LCD backlight control: off/restore */ -#define REG_BACKLIGHT_CTRL 0xF7BD -#define BIT_BACKLIGHT_ON 1 -#define BIT_BACKLIGHT_OFF 0 +#define REG_BACKLIGHT_CTRL 0xF7BD +#define BIT_BACKLIGHT_ON 1 +#define BIT_BACKLIGHT_OFF 0 /* Reset the machine auto-clear: rd/wr */ -#define REG_RESET 0xF4EC -#define BIT_RESET_ON 1 +#define REG_RESET 0xF4EC +#define BIT_RESET_ON 1 /* Light the led: rd/wr */ -#define REG_LED 0xF4C8 -#define BIT_LED_RED_POWER (1 << 0) -#define BIT_LED_ORANGE_POWER (1 << 1) -#define BIT_LED_GREEN_CHARGE (1 << 2) -#define BIT_LED_RED_CHARGE (1 << 3) -#define BIT_LED_NUMLOCK (1 << 4) +#define REG_LED 0xF4C8 +#define BIT_LED_RED_POWER (1 << 0) +#define BIT_LED_ORANGE_POWER (1 << 1) +#define BIT_LED_GREEN_CHARGE (1 << 2) +#define BIT_LED_RED_CHARGE (1 << 3) +#define BIT_LED_NUMLOCK (1 << 4) /* Test led mode, all led on/off */ -#define REG_LED_TEST 0xF4C2 -#define BIT_LED_TEST_IN 1 -#define BIT_LED_TEST_OUT 0 +#define REG_LED_TEST 0xF4C2 +#define BIT_LED_TEST_IN 1 +#define BIT_LED_TEST_OUT 0 /* Camera on/off */ -#define REG_CAMERA_STATUS 0xF46A -#define BIT_CAMERA_STATUS_ON 1 -#define BIT_CAMERA_STATUS_OFF 0 -#define REG_CAMERA_CONTROL 0xF7B7 -#define BIT_CAMERA_CONTROL_OFF 0 -#define BIT_CAMERA_CONTROL_ON 1 +#define REG_CAMERA_STATUS 0xF46A +#define BIT_CAMERA_STATUS_ON 1 +#define BIT_CAMERA_STATUS_OFF 0 +#define REG_CAMERA_CONTROL 0xF7B7 +#define BIT_CAMERA_CONTROL_OFF 0 +#define BIT_CAMERA_CONTROL_ON 1 /* Wlan Status */ -#define REG_WLAN 0xF4FA -#define BIT_WLAN_ON 1 -#define BIT_WLAN_OFF 0 -#define REG_DISPLAY_LCD 0xF79F +#define REG_WLAN 0xF4FA +#define BIT_WLAN_ON 1 +#define BIT_WLAN_OFF 0 +#define REG_DISPLAY_LCD 0xF79F /* SCI Event Number from EC */ enum { |