diff options
Diffstat (limited to 'arch/powerpc/boot/dts/akebono.dts')
| -rw-r--r-- | arch/powerpc/boot/dts/akebono.dts | 415 |
1 files changed, 415 insertions, 0 deletions
diff --git a/arch/powerpc/boot/dts/akebono.dts b/arch/powerpc/boot/dts/akebono.dts new file mode 100644 index 00000000000..f92ecfed3d2 --- /dev/null +++ b/arch/powerpc/boot/dts/akebono.dts @@ -0,0 +1,415 @@ +/* + * Device Tree Source for IBM Embedded PPC 476 Platform + * + * Copyright © 2013 Tony Breeds IBM Corporation + * Copyright © 2013 Alistair Popple IBM Corporation + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without + * any warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +/memreserve/ 0x01f00000 0x00100000; // spin table + +/ { + #address-cells = <2>; + #size-cells = <2>; + model = "ibm,akebono"; + compatible = "ibm,akebono", "ibm,476gtr"; + dcr-parent = <&{/cpus/cpu@0}>; + + aliases { + serial0 = &UART0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + model = "PowerPC,476"; + reg = <0>; + clock-frequency = <1600000000>; // 1.6 GHz + timebase-frequency = <100000000>; // 100Mhz + i-cache-line-size = <32>; + d-cache-line-size = <32>; + i-cache-size = <32768>; + d-cache-size = <32768>; + dcr-controller; + dcr-access-method = "native"; + status = "ok"; + }; + cpu@1 { + device_type = "cpu"; + model = "PowerPC,476"; + reg = <1>; + clock-frequency = <1600000000>; // 1.6 GHz + timebase-frequency = <100000000>; // 100Mhz + i-cache-line-size = <32>; + d-cache-line-size = <32>; + i-cache-size = <32768>; + d-cache-size = <32768>; + dcr-controller; + dcr-access-method = "native"; + status = "disabled"; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x01f00000>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x0>; // filled in by zImage + }; + + MPIC: interrupt-controller { + compatible = "chrp,open-pic"; + interrupt-controller; + dcr-reg = <0xffc00000 0x00040000>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + single-cpu-affinity; + }; + + plb { + compatible = "ibm,plb6"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clock-frequency = <200000000>; // 200Mhz + + HSTA0: hsta@310000e0000 { + compatible = "ibm,476gtr-hsta-msi", "ibm,hsta-msi"; + reg = <0x310 0x000e0000 0x0 0xf0>; + interrupt-parent = <&MPIC>; + interrupts = <108 0 + 109 0 + 110 0 + 111 0 + 112 0 + 113 0 + 114 0 + 115 0 + 116 0 + 117 0 + 118 0 + 119 0 + 120 0 + 121 0 + 122 0 + 123 0>; + }; + + MAL0: mcmal { + compatible = "ibm,mcmal-476gtr", "ibm,mcmal2"; + dcr-reg = <0xc0000000 0x062>; + num-tx-chans = <1>; + num-rx-chans = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-parent = <&MPIC>; + interrupts = < /*TXEOB*/ 77 0x4 + /*RXEOB*/ 78 0x4 + /*SERR*/ 76 0x4 + /*TXDE*/ 79 0x4 + /*RXDE*/ 80 0x4>; + }; + + SATA0: sata@30000010000 { + compatible = "ibm,476gtr-ahci"; + reg = <0x300 0x00010000 0x0 0x10000>; + interrupt-parent = <&MPIC>; + interrupts = <93 2>; + }; + + EHCI0: ehci@30010000000 { + compatible = "ibm,476gtr-ehci", "generic-ehci"; + reg = <0x300 0x10000000 0x0 0x10000>; + interrupt-parent = <&MPIC>; + interrupts = <85 2>; + }; + + SD0: sd@30000000000 { + compatible = "ibm,476gtr-sdhci", "generic-sdhci"; + reg = <0x300 0x00000000 0x0 0x10000>; + interrupts = <91 2>; + interrupt-parent = <&MPIC>; + }; + + OHCI0: ohci@30010010000 { + compatible = "ibm,476gtr-ohci", "generic-ohci"; + reg = <0x300 0x10010000 0x0 0x10000>; + interrupt-parent = <&MPIC>; + interrupts = <89 1>; + }; + + OHCI1: ohci@30010020000 { + compatible = "ibm,476gtr-ohci", "generic-ohci"; + reg = <0x300 0x10020000 0x0 0x10000>; + interrupt-parent = <&MPIC>; + interrupts = <88 1>; + }; + + POB0: opb { + compatible = "ibm,opb-4xx", "ibm,opb"; + #address-cells = <1>; + #size-cells = <1>; + /* Wish there was a nicer way of specifying a full + * 32-bit range + */ + ranges = <0x00000000 0x0000033f 0x00000000 0x80000000 + 0x80000000 0x0000033f 0x80000000 0x80000000>; + clock-frequency = <100000000>; + + RGMII0: emac-rgmii-wol@50004 { + compatible = "ibm,rgmii-wol-476gtr", "ibm,rgmii-wol"; + reg = <0x50004 0x00000008>; + has-mdio; + }; + + EMAC0: ethernet@30000 { + device_type = "network"; + compatible = "ibm,emac-476gtr", "ibm,emac4sync"; + interrupt-parent = <&EMAC0>; + interrupts = <0x0 0x1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = </*Status*/ 0x0 &MPIC 81 0x4 + /*Wake*/ 0x1 &MPIC 82 0x4>; + reg = <0x30000 0x78>; + + /* local-mac-address will normally be added by + * the wrapper. If your device doesn't support + * passing data to the wrapper (in the form + * local-mac-addr=<hwaddr>) then you will need + * to set it manually here. */ + //local-mac-address = [000000000000]; + + mal-device = <&MAL0>; + mal-tx-channel = <0>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <9000>; + rx-fifo-size = <4096>; + tx-fifo-size = <2048>; + rx-fifo-size-gige = <16384>; + phy-mode = "rgmii"; + phy-map = <0x00000000>; + rgmii-wol-device = <&RGMII0>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + }; + + UART0: serial@10000 { + device_type = "serial"; + compatible = "ns16750", "ns16550"; + reg = <0x10000 0x00000008>; + virtual-reg = <0xe8010000>; + clock-frequency = <1851851>; + current-speed = <38400>; + interrupt-parent = <&MPIC>; + interrupts = <39 2>; + }; + + IIC0: i2c@00000000 { + compatible = "ibm,iic-476gtr", "ibm,iic"; + reg = <0x0 0x00000020>; + interrupt-parent = <&MPIC>; + interrupts = <37 2>; + #address-cells = <1>; + #size-cells = <0>; + rtc@68 { + compatible = "stm,m41t80", "m41st85"; + reg = <0x68>; + }; + }; + + IIC1: i2c@00000100 { + compatible = "ibm,iic-476gtr", "ibm,iic"; + reg = <0x100 0x00000020>; + interrupt-parent = <&MPIC>; + interrupts = <38 2>; + #address-cells = <1>; + #size-cells = <0>; + avr@58 { + compatible = "ibm,akebono-avr"; + reg = <0x58>; + }; + }; + + FPGA0: fpga@ebc00000 { + compatible = "ibm,akebono-fpga"; + reg = <0xebc00000 0x8>; + }; + }; + + PCIE0: pciex@10100000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex"; + primary; + port = <0x0>; /* port number */ + reg = <0x00000101 0x00000000 0x0 0x10000000 /* Config space access */ + 0x00000100 0x00000000 0x0 0x00001000>; /* UTL Registers space access */ + dcr-reg = <0xc0 0x20>; + +// pci_space < pci_addr > < cpu_addr > < size > + ranges = <0x02000000 0x00000000 0x80000000 0x00000110 0x80000000 0x0 0x80000000 + 0x01000000 0x0 0x0 0x00000140 0x0 0x0 0x00010000>; + + /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI + * PCI devices must be able to write to the HSTA module. + */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>; + + /* This drives busses 0 to 0xf */ + bus-range = <0x0 0xf>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &MPIC 45 0x2 /* int A */ + 0x0 0x0 0x0 0x2 &MPIC 46 0x2 /* int B */ + 0x0 0x0 0x0 0x3 &MPIC 47 0x2 /* int C */ + 0x0 0x0 0x0 0x4 &MPIC 48 0x2 /* int D */>; + }; + + PCIE1: pciex@20100000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex"; + primary; + port = <0x1>; /* port number */ + reg = <0x00000201 0x00000000 0x0 0x10000000 /* Config space access */ + 0x00000200 0x00000000 0x0 0x00001000>; /* UTL Registers space access */ + dcr-reg = <0x100 0x20>; + +// pci_space < pci_addr > < cpu_addr > < size > + ranges = <0x02000000 0x00000000 0x80000000 0x00000210 0x80000000 0x0 0x80000000 + 0x01000000 0x0 0x0 0x00000240 0x0 0x0 0x00010000>; + + /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI + * PCI devices must be able to write to the HSTA module. + */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>; + + /* This drives busses 0 to 0xf */ + bus-range = <0x0 0xf>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &MPIC 53 0x2 /* int A */ + 0x0 0x0 0x0 0x2 &MPIC 54 0x2 /* int B */ + 0x0 0x0 0x0 0x3 &MPIC 55 0x2 /* int C */ + 0x0 0x0 0x0 0x4 &MPIC 56 0x2 /* int D */>; + }; + + PCIE2: pciex@18100000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex"; + primary; + port = <0x2>; /* port number */ + reg = <0x00000181 0x00000000 0x0 0x10000000 /* Config space access */ + 0x00000180 0x00000000 0x0 0x00001000>; /* UTL Registers space access */ + dcr-reg = <0xe0 0x20>; + +// pci_space < pci_addr > < cpu_addr > < size > + ranges = <0x02000000 0x00000000 0x80000000 0x00000190 0x80000000 0x0 0x80000000 + 0x01000000 0x0 0x0 0x000001c0 0x0 0x0 0x00010000>; + + /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI + * PCI devices must be able to write to the HSTA module. + */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>; + + /* This drives busses 0 to 0xf */ + bus-range = <0x0 0xf>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &MPIC 61 0x2 /* int A */ + 0x0 0x0 0x0 0x2 &MPIC 62 0x2 /* int B */ + 0x0 0x0 0x0 0x3 &MPIC 63 0x2 /* int C */ + 0x0 0x0 0x0 0x4 &MPIC 64 0x2 /* int D */>; + }; + + PCIE3: pciex@28100000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex"; + primary; + port = <0x3>; /* port number */ + reg = <0x00000281 0x00000000 0x0 0x10000000 /* Config space access */ + 0x00000280 0x00000000 0x0 0x00001000>; /* UTL Registers space access */ + dcr-reg = <0x120 0x20>; + +// pci_space < pci_addr > < cpu_addr > < size > + ranges = <0x02000000 0x00000000 0x80000000 0x00000290 0x80000000 0x0 0x80000000 + 0x01000000 0x0 0x0 0x000002c0 0x0 0x0 0x00010000>; + + /* Inbound starting at 0x0 to 0x40000000000. In order to use MSI + * PCI devices must be able to write to the HSTA module. + */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x400 0x0>; + + /* This drives busses 0 to 0xf */ + bus-range = <0x0 0xf>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &MPIC 69 0x2 /* int A */ + 0x0 0x0 0x0 0x2 &MPIC 70 0x2 /* int B */ + 0x0 0x0 0x0 0x3 &MPIC 71 0x2 /* int C */ + 0x0 0x0 0x0 0x4 &MPIC 72 0x2 /* int D */>; + }; + }; + + chosen { + linux,stdout-path = &UART0; + }; +}; |