1 files changed, 0 insertions, 84 deletions

diff --git a/arch/powerpc/kernel/prom_parse.c b/arch/powerpc/kernel/prom_parse.c
index c2b7a07cc3d..47187cc2cf0 100644
--- a/arch/powerpc/kernel/prom_parse.c
+++ b/arch/powerpc/kernel/prom_parse.c
@@ -2,95 +2,11 @@
 
 #include <linux/kernel.h>
 #include <linux/string.h>
-#include <linux/pci_regs.h>
 #include <linux/module.h>
 #include <linux/ioport.h>
 #include <linux/etherdevice.h>
 #include <linux/of_address.h>
 #include <asm/prom.h>
-#include <asm/pci-bridge.h>
-
-#ifdef CONFIG_PCI
-int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq)
-{
-	struct device_node *dn, *ppnode;
-	struct pci_dev *ppdev;
-	u32 lspec;
-	u32 laddr[3];
-	u8 pin;
-	int rc;
-
-	/* Check if we have a device node, if yes, fallback to standard OF
-	 * parsing
-	 */
-	dn = pci_device_to_OF_node(pdev);
-	if (dn) {
-		rc = of_irq_map_one(dn, 0, out_irq);
-		if (!rc)
-			return rc;
-	}
-
-	/* Ok, we don't, time to have fun. Let's start by building up an
-	 * interrupt spec.  we assume #interrupt-cells is 1, which is standard
-	 * for PCI. If you do different, then don't use that routine.
-	 */
-	rc = pci_read_config_byte(pdev, PCI_INTERRUPT_PIN, &pin);
-	if (rc != 0)
-		return rc;
-	/* No pin, exit */
-	if (pin == 0)
-		return -ENODEV;
-
-	/* Now we walk up the PCI tree */
-	lspec = pin;
-	for (;;) {
-		/* Get the pci_dev of our parent */
-		ppdev = pdev->bus->self;
-
-		/* Ouch, it's a host bridge... */
-		if (ppdev == NULL) {
-#ifdef CONFIG_PPC64
-			ppnode = pci_bus_to_OF_node(pdev->bus);
-#else
-			struct pci_controller *host;
-			host = pci_bus_to_host(pdev->bus);
-			ppnode = host ? host->dn : NULL;
-#endif
-			/* No node for host bridge ? give up */
-			if (ppnode == NULL)
-				return -EINVAL;
-		} else
-			/* We found a P2P bridge, check if it has a node */
-			ppnode = pci_device_to_OF_node(ppdev);
-
-		/* Ok, we have found a parent with a device-node, hand over to
-		 * the OF parsing code.
-		 * We build a unit address from the linux device to be used for
-		 * resolution. Note that we use the linux bus number which may
-		 * not match your firmware bus numbering.
-		 * Fortunately, in most cases, interrupt-map-mask doesn't include
-		 * the bus number as part of the matching.
-		 * You should still be careful about that though if you intend
-		 * to rely on this function (you ship  a firmware that doesn't
-		 * create device nodes for all PCI devices).
-		 */
-		if (ppnode)
-			break;
-
-		/* We can only get here if we hit a P2P bridge with no node,
-		 * let's do standard swizzling and try again
-		 */
-		lspec = pci_swizzle_interrupt_pin(pdev, lspec);
-		pdev = ppdev;
-	}
-
-	laddr[0] = (pdev->bus->number << 16)
-		| (pdev->devfn << 8);
-	laddr[1]  = laddr[2] = 0;
-	return of_irq_map_raw(ppnode, &lspec, 1, laddr, out_irq);
-}
-EXPORT_SYMBOL_GPL(of_irq_map_pci);
-#endif /* CONFIG_PCI */
 
 void of_parse_dma_window(struct device_node *dn, const void *dma_window_prop,
 		unsigned long *busno, unsigned long *phys, unsigned long *size)