diff options
Diffstat (limited to 'arch/powerpc/platforms/powermac/smp.c')
| -rw-r--r-- | arch/powerpc/platforms/powermac/smp.c | 878 |
1 files changed, 878 insertions, 0 deletions
diff --git a/arch/powerpc/platforms/powermac/smp.c b/arch/powerpc/platforms/powermac/smp.c new file mode 100644 index 00000000000..fb2a7c798e8 --- /dev/null +++ b/arch/powerpc/platforms/powermac/smp.c @@ -0,0 +1,878 @@ +/* + * SMP support for power macintosh. + * + * We support both the old "powersurge" SMP architecture + * and the current Core99 (G4 PowerMac) machines. + * + * Note that we don't support the very first rev. of + * Apple/DayStar 2 CPUs board, the one with the funky + * watchdog. Hopefully, none of these should be there except + * maybe internally to Apple. I should probably still add some + * code to detect this card though and disable SMP. --BenH. + * + * Support Macintosh G4 SMP by Troy Benjegerdes (hozer@drgw.net) + * and Ben Herrenschmidt <benh@kernel.crashing.org>. + * + * Support for DayStar quad CPU cards + * Copyright (C) XLR8, Inc. 1994-2000 + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ +#include <linux/config.h> +#include <linux/kernel.h> +#include <linux/sched.h> +#include <linux/smp.h> +#include <linux/smp_lock.h> +#include <linux/interrupt.h> +#include <linux/kernel_stat.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <linux/spinlock.h> +#include <linux/errno.h> +#include <linux/hardirq.h> +#include <linux/cpu.h> +#include <linux/compiler.h> + +#include <asm/ptrace.h> +#include <asm/atomic.h> +#include <asm/irq.h> +#include <asm/page.h> +#include <asm/pgtable.h> +#include <asm/sections.h> +#include <asm/io.h> +#include <asm/prom.h> +#include <asm/smp.h> +#include <asm/machdep.h> +#include <asm/pmac_feature.h> +#include <asm/time.h> +#include <asm/mpic.h> +#include <asm/cacheflush.h> +#include <asm/keylargo.h> +#include <asm/pmac_low_i2c.h> + +#undef DEBUG + +#ifdef DEBUG +#define DBG(fmt...) udbg_printf(fmt) +#else +#define DBG(fmt...) +#endif + +extern void __secondary_start_pmac_0(void); + +#ifdef CONFIG_PPC32 + +/* Sync flag for HW tb sync */ +static volatile int sec_tb_reset = 0; + +/* + * Powersurge (old powermac SMP) support. + */ + +/* Addresses for powersurge registers */ +#define HAMMERHEAD_BASE 0xf8000000 +#define HHEAD_CONFIG 0x90 +#define HHEAD_SEC_INTR 0xc0 + +/* register for interrupting the primary processor on the powersurge */ +/* N.B. this is actually the ethernet ROM! */ +#define PSURGE_PRI_INTR 0xf3019000 + +/* register for storing the start address for the secondary processor */ +/* N.B. this is the PCI config space address register for the 1st bridge */ +#define PSURGE_START 0xf2800000 + +/* Daystar/XLR8 4-CPU card */ +#define PSURGE_QUAD_REG_ADDR 0xf8800000 + +#define PSURGE_QUAD_IRQ_SET 0 +#define PSURGE_QUAD_IRQ_CLR 1 +#define PSURGE_QUAD_IRQ_PRIMARY 2 +#define PSURGE_QUAD_CKSTOP_CTL 3 +#define PSURGE_QUAD_PRIMARY_ARB 4 +#define PSURGE_QUAD_BOARD_ID 6 +#define PSURGE_QUAD_WHICH_CPU 7 +#define PSURGE_QUAD_CKSTOP_RDBK 8 +#define PSURGE_QUAD_RESET_CTL 11 + +#define PSURGE_QUAD_OUT(r, v) (out_8(quad_base + ((r) << 4) + 4, (v))) +#define PSURGE_QUAD_IN(r) (in_8(quad_base + ((r) << 4) + 4) & 0x0f) +#define PSURGE_QUAD_BIS(r, v) (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) | (v))) +#define PSURGE_QUAD_BIC(r, v) (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) & ~(v))) + +/* virtual addresses for the above */ +static volatile u8 __iomem *hhead_base; +static volatile u8 __iomem *quad_base; +static volatile u32 __iomem *psurge_pri_intr; +static volatile u8 __iomem *psurge_sec_intr; +static volatile u32 __iomem *psurge_start; + +/* values for psurge_type */ +#define PSURGE_NONE -1 +#define PSURGE_DUAL 0 +#define PSURGE_QUAD_OKEE 1 +#define PSURGE_QUAD_COTTON 2 +#define PSURGE_QUAD_ICEGRASS 3 + +/* what sort of powersurge board we have */ +static int psurge_type = PSURGE_NONE; + +/* + * Set and clear IPIs for powersurge. + */ +static inline void psurge_set_ipi(int cpu) +{ + if (psurge_type == PSURGE_NONE) + return; + if (cpu == 0) + in_be32(psurge_pri_intr); + else if (psurge_type == PSURGE_DUAL) + out_8(psurge_sec_intr, 0); + else + PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_SET, 1 << cpu); +} + +static inline void psurge_clr_ipi(int cpu) +{ + if (cpu > 0) { + switch(psurge_type) { + case PSURGE_DUAL: + out_8(psurge_sec_intr, ~0); + case PSURGE_NONE: + break; + default: + PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, 1 << cpu); + } + } +} + +/* + * On powersurge (old SMP powermac architecture) we don't have + * separate IPIs for separate messages like openpic does. Instead + * we have a bitmap for each processor, where a 1 bit means that + * the corresponding message is pending for that processor. + * Ideally each cpu's entry would be in a different cache line. + * -- paulus. + */ +static unsigned long psurge_smp_message[NR_CPUS]; + +void psurge_smp_message_recv(struct pt_regs *regs) +{ + int cpu = smp_processor_id(); + int msg; + + /* clear interrupt */ + psurge_clr_ipi(cpu); + + if (num_online_cpus() < 2) + return; + + /* make sure there is a message there */ + for (msg = 0; msg < 4; msg++) + if (test_and_clear_bit(msg, &psurge_smp_message[cpu])) + smp_message_recv(msg, regs); +} + +irqreturn_t psurge_primary_intr(int irq, void *d, struct pt_regs *regs) +{ + psurge_smp_message_recv(regs); + return IRQ_HANDLED; +} + +static void smp_psurge_message_pass(int target, int msg) +{ + int i; + + if (num_online_cpus() < 2) + return; + + for (i = 0; i < NR_CPUS; i++) { + if (!cpu_online(i)) + continue; + if (target == MSG_ALL + || (target == MSG_ALL_BUT_SELF && i != smp_processor_id()) + || target == i) { + set_bit(msg, &psurge_smp_message[i]); + psurge_set_ipi(i); + } + } +} + +/* + * Determine a quad card presence. We read the board ID register, we + * force the data bus to change to something else, and we read it again. + * It it's stable, then the register probably exist (ugh !) + */ +static int __init psurge_quad_probe(void) +{ + int type; + unsigned int i; + + type = PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID); + if (type < PSURGE_QUAD_OKEE || type > PSURGE_QUAD_ICEGRASS + || type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID)) + return PSURGE_DUAL; + + /* looks OK, try a slightly more rigorous test */ + /* bogus is not necessarily cacheline-aligned, + though I don't suppose that really matters. -- paulus */ + for (i = 0; i < 100; i++) { + volatile u32 bogus[8]; + bogus[(0+i)%8] = 0x00000000; + bogus[(1+i)%8] = 0x55555555; + bogus[(2+i)%8] = 0xFFFFFFFF; + bogus[(3+i)%8] = 0xAAAAAAAA; + bogus[(4+i)%8] = 0x33333333; + bogus[(5+i)%8] = 0xCCCCCCCC; + bogus[(6+i)%8] = 0xCCCCCCCC; + bogus[(7+i)%8] = 0x33333333; + wmb(); + asm volatile("dcbf 0,%0" : : "r" (bogus) : "memory"); + mb(); + if (type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID)) + return PSURGE_DUAL; + } + return type; +} + +static void __init psurge_quad_init(void) +{ + int procbits; + + if (ppc_md.progress) ppc_md.progress("psurge_quad_init", 0x351); + procbits = ~PSURGE_QUAD_IN(PSURGE_QUAD_WHICH_CPU); + if (psurge_type == PSURGE_QUAD_ICEGRASS) + PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits); + else + PSURGE_QUAD_BIC(PSURGE_QUAD_CKSTOP_CTL, procbits); + mdelay(33); + out_8(psurge_sec_intr, ~0); + PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, procbits); + PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits); + if (psurge_type != PSURGE_QUAD_ICEGRASS) + PSURGE_QUAD_BIS(PSURGE_QUAD_CKSTOP_CTL, procbits); + PSURGE_QUAD_BIC(PSURGE_QUAD_PRIMARY_ARB, procbits); + mdelay(33); + PSURGE_QUAD_BIC(PSURGE_QUAD_RESET_CTL, procbits); + mdelay(33); + PSURGE_QUAD_BIS(PSURGE_QUAD_PRIMARY_ARB, procbits); + mdelay(33); +} + +static int __init smp_psurge_probe(void) +{ + int i, ncpus; + + /* We don't do SMP on the PPC601 -- paulus */ + if (PVR_VER(mfspr(SPRN_PVR)) == 1) + return 1; + + /* + * The powersurge cpu board can be used in the generation + * of powermacs that have a socket for an upgradeable cpu card, + * including the 7500, 8500, 9500, 9600. + * The device tree doesn't tell you if you have 2 cpus because + * OF doesn't know anything about the 2nd processor. + * Instead we look for magic bits in magic registers, + * in the hammerhead memory controller in the case of the + * dual-cpu powersurge board. -- paulus. + */ + if (find_devices("hammerhead") == NULL) + return 1; + + hhead_base = ioremap(HAMMERHEAD_BASE, 0x800); + quad_base = ioremap(PSURGE_QUAD_REG_ADDR, 1024); + psurge_sec_intr = hhead_base + HHEAD_SEC_INTR; + + psurge_type = psurge_quad_probe(); + if (psurge_type != PSURGE_DUAL) { + psurge_quad_init(); + /* All released cards using this HW design have 4 CPUs */ + ncpus = 4; + } else { + iounmap(quad_base); + if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) { + /* not a dual-cpu card */ + iounmap(hhead_base); + psurge_type = PSURGE_NONE; + return 1; + } + ncpus = 2; + } + + psurge_start = ioremap(PSURGE_START, 4); + psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4); + + /* + * This is necessary because OF doesn't know about the + * secondary cpu(s), and thus there aren't nodes in the + * device tree for them, and smp_setup_cpu_maps hasn't + * set their bits in cpu_possible_map and cpu_present_map. + */ + if (ncpus > NR_CPUS) + ncpus = NR_CPUS; + for (i = 1; i < ncpus ; ++i) { + cpu_set(i, cpu_present_map); + cpu_set(i, cpu_possible_map); + set_hard_smp_processor_id(i, i); + } + + if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352); + + return ncpus; +} + +static void __init smp_psurge_kick_cpu(int nr) +{ + unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8; + unsigned long a; + + /* may need to flush here if secondary bats aren't setup */ + for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32) + asm volatile("dcbf 0,%0" : : "r" (a) : "memory"); + asm volatile("sync"); + + if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353); + + out_be32(psurge_start, start); + mb(); + + psurge_set_ipi(nr); + udelay(10); + psurge_clr_ipi(nr); + + if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354); +} + +/* + * With the dual-cpu powersurge board, the decrementers and timebases + * of both cpus are frozen after the secondary cpu is started up, + * until we give the secondary cpu another interrupt. This routine + * uses this to get the timebases synchronized. + * -- paulus. + */ +static void __init psurge_dual_sync_tb(int cpu_nr) +{ + int t; + + set_dec(tb_ticks_per_jiffy); + /* XXX fixme */ + set_tb(0, 0); + last_jiffy_stamp(cpu_nr) = 0; + + if (cpu_nr > 0) { + mb(); + sec_tb_reset = 1; + return; + } + + /* wait for the secondary to have reset its TB before proceeding */ + for (t = 10000000; t > 0 && !sec_tb_reset; --t) + ; + + /* now interrupt the secondary, starting both TBs */ + psurge_set_ipi(1); +} + +static struct irqaction psurge_irqaction = { + .handler = psurge_primary_intr, + .flags = SA_INTERRUPT, + .mask = CPU_MASK_NONE, + .name = "primary IPI", +}; + +static void __init smp_psurge_setup_cpu(int cpu_nr) +{ + + if (cpu_nr == 0) { + /* If we failed to start the second CPU, we should still + * send it an IPI to start the timebase & DEC or we might + * have them stuck. + */ + if (num_online_cpus() < 2) { + if (psurge_type == PSURGE_DUAL) + psurge_set_ipi(1); + return; + } + /* reset the entry point so if we get another intr we won't + * try to startup again */ + out_be32(psurge_start, 0x100); + if (setup_irq(30, &psurge_irqaction)) + printk(KERN_ERR "Couldn't get primary IPI interrupt"); + } + + if (psurge_type == PSURGE_DUAL) + psurge_dual_sync_tb(cpu_nr); +} + +void __init smp_psurge_take_timebase(void) +{ + /* Dummy implementation */ +} + +void __init smp_psurge_give_timebase(void) +{ + /* Dummy implementation */ +} + +/* PowerSurge-style Macs */ +struct smp_ops_t psurge_smp_ops = { + .message_pass = smp_psurge_message_pass, + .probe = smp_psurge_probe, + .kick_cpu = smp_psurge_kick_cpu, + .setup_cpu = smp_psurge_setup_cpu, + .give_timebase = smp_psurge_give_timebase, + .take_timebase = smp_psurge_take_timebase, +}; +#endif /* CONFIG_PPC32 - actually powersurge support */ + +#ifdef CONFIG_PPC64 +/* + * G5s enable/disable the timebase via an i2c-connected clock chip. + */ +static struct device_node *pmac_tb_clock_chip_host; +static u8 pmac_tb_pulsar_addr; +static void (*pmac_tb_freeze)(int freeze); +static DEFINE_SPINLOCK(timebase_lock); +static unsigned long timebase; + +static void smp_core99_cypress_tb_freeze(int freeze) +{ + u8 data; + int rc; + + /* Strangely, the device-tree says address is 0xd2, but darwin + * accesses 0xd0 ... + */ + pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_combined); + rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host, + 0xd0 | pmac_low_i2c_read, + 0x81, &data, 1); + if (rc != 0) + goto bail; + + data = (data & 0xf3) | (freeze ? 0x00 : 0x0c); + + pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_stdsub); + rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host, + 0xd0 | pmac_low_i2c_write, + 0x81, &data, 1); + + bail: + if (rc != 0) { + printk("Cypress Timebase %s rc: %d\n", + freeze ? "freeze" : "unfreeze", rc); + panic("Timebase freeze failed !\n"); + } +} + + +static void smp_core99_pulsar_tb_freeze(int freeze) +{ + u8 data; + int rc; + + pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_combined); + rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host, + pmac_tb_pulsar_addr | pmac_low_i2c_read, + 0x2e, &data, 1); + if (rc != 0) + goto bail; + + data = (data & 0x88) | (freeze ? 0x11 : 0x22); + + pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_stdsub); + rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host, + pmac_tb_pulsar_addr | pmac_low_i2c_write, + 0x2e, &data, 1); + bail: + if (rc != 0) { + printk(KERN_ERR "Pulsar Timebase %s rc: %d\n", + freeze ? "freeze" : "unfreeze", rc); + panic("Timebase freeze failed !\n"); + } +} + + +static void smp_core99_give_timebase(void) +{ + /* Open i2c bus for synchronous access */ + if (pmac_low_i2c_open(pmac_tb_clock_chip_host, 0)) + panic("Can't open i2c for TB sync !\n"); + + spin_lock(&timebase_lock); + (*pmac_tb_freeze)(1); + mb(); + timebase = get_tb(); + spin_unlock(&timebase_lock); + + while (timebase) + barrier(); + + spin_lock(&timebase_lock); + (*pmac_tb_freeze)(0); + spin_unlock(&timebase_lock); + + /* Close i2c bus */ + pmac_low_i2c_close(pmac_tb_clock_chip_host); +} + + +static void __devinit smp_core99_take_timebase(void) +{ + while (!timebase) + barrier(); + spin_lock(&timebase_lock); + set_tb(timebase >> 32, timebase & 0xffffffff); + timebase = 0; + spin_unlock(&timebase_lock); +} + +static void __init smp_core99_setup(int ncpus) +{ + struct device_node *cc = NULL; + struct device_node *p; + u32 *reg; + int ok; + + /* HW sync only on these platforms */ + if (!machine_is_compatible("PowerMac7,2") && + !machine_is_compatible("PowerMac7,3") && + !machine_is_compatible("RackMac3,1")) + return; + + /* Look for the clock chip */ + while ((cc = of_find_node_by_name(cc, "i2c-hwclock")) != NULL) { + p = of_get_parent(cc); + ok = p && device_is_compatible(p, "uni-n-i2c"); + of_node_put(p); + if (!ok) + continue; + + reg = (u32 *)get_property(cc, "reg", NULL); + if (reg == NULL) + continue; + + switch (*reg) { + case 0xd2: + if (device_is_compatible(cc, "pulsar-legacy-slewing")) { + pmac_tb_freeze = smp_core99_pulsar_tb_freeze; + pmac_tb_pulsar_addr = 0xd2; + printk(KERN_INFO "Timebase clock is Pulsar chip\n"); + } else if (device_is_compatible(cc, "cy28508")) { + pmac_tb_freeze = smp_core99_cypress_tb_freeze; + printk(KERN_INFO "Timebase clock is Cypress chip\n"); + } + break; + case 0xd4: + pmac_tb_freeze = smp_core99_pulsar_tb_freeze; + pmac_tb_pulsar_addr = 0xd4; + printk(KERN_INFO "Timebase clock is Pulsar chip\n"); + break; + } + if (pmac_tb_freeze != NULL) { + pmac_tb_clock_chip_host = of_get_parent(cc); + of_node_put(cc); + break; + } + } + if (pmac_tb_freeze == NULL) { + smp_ops->give_timebase = smp_generic_give_timebase; + smp_ops->take_timebase = smp_generic_take_timebase; + } +} + +/* nothing to do here, caches are already set up by service processor */ +static inline void __devinit core99_init_caches(int cpu) +{ +} + +#else /* CONFIG_PPC64 */ + +/* + * SMP G4 powermacs use a GPIO to enable/disable the timebase. + */ + +static unsigned int core99_tb_gpio; /* Timebase freeze GPIO */ + +static unsigned int pri_tb_hi, pri_tb_lo; +static unsigned int pri_tb_stamp; + +/* not __init, called in sleep/wakeup code */ +void smp_core99_give_timebase(void) +{ + unsigned long flags; + unsigned int t; + + /* wait for the secondary to be in take_timebase */ + for (t = 100000; t > 0 && !sec_tb_reset; --t) + udelay(10); + if (!sec_tb_reset) { + printk(KERN_WARNING "Timeout waiting sync on second CPU\n"); + return; + } + + /* freeze the timebase and read it */ + /* disable interrupts so the timebase is disabled for the + shortest possible time */ + local_irq_save(flags); + pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 4); + pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0); + mb(); + pri_tb_hi = get_tbu(); + pri_tb_lo = get_tbl(); + pri_tb_stamp = last_jiffy_stamp(smp_processor_id()); + mb(); + + /* tell the secondary we're ready */ + sec_tb_reset = 2; + mb(); + + /* wait for the secondary to have taken it */ + /* note: can't use udelay here, since it needs the timebase running */ + for (t = 10000000; t > 0 && sec_tb_reset; --t) + barrier(); + if (sec_tb_reset) + /* XXX BUG_ON here? */ + printk(KERN_WARNING "Timeout waiting sync(2) on second CPU\n"); + + /* Now, restart the timebase by leaving the GPIO to an open collector */ + pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 0); + pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0); + local_irq_restore(flags); +} + +/* not __init, called in sleep/wakeup code */ +void smp_core99_take_timebase(void) +{ + unsigned long flags; + + /* tell the primary we're here */ + sec_tb_reset = 1; + mb(); + + /* wait for the primary to set pri_tb_hi/lo */ + while (sec_tb_reset < 2) + mb(); + + /* set our stuff the same as the primary */ + local_irq_save(flags); + set_dec(1); + set_tb(pri_tb_hi, pri_tb_lo); + last_jiffy_stamp(smp_processor_id()) = pri_tb_stamp; + mb(); + + /* tell the primary we're done */ + sec_tb_reset = 0; + mb(); + local_irq_restore(flags); +} + +/* L2 and L3 cache settings to pass from CPU0 to CPU1 on G4 cpus */ +volatile static long int core99_l2_cache; +volatile static long int core99_l3_cache; + +static void __devinit core99_init_caches(int cpu) +{ + if (!cpu_has_feature(CPU_FTR_L2CR)) + return; + + if (cpu == 0) { + core99_l2_cache = _get_L2CR(); + printk("CPU0: L2CR is %lx\n", core99_l2_cache); + } else { + printk("CPU%d: L2CR was %lx\n", cpu, _get_L2CR()); + _set_L2CR(0); + _set_L2CR(core99_l2_cache); + printk("CPU%d: L2CR set to %lx\n", cpu, core99_l2_cache); + } + + if (!cpu_has_feature(CPU_FTR_L3CR)) + return; + + if (cpu == 0){ + core99_l3_cache = _get_L3CR(); + printk("CPU0: L3CR is %lx\n", core99_l3_cache); + } else { + printk("CPU%d: L3CR was %lx\n", cpu, _get_L3CR()); + _set_L3CR(0); + _set_L3CR(core99_l3_cache); + printk("CPU%d: L3CR set to %lx\n", cpu, core99_l3_cache); + } +} + +static void __init smp_core99_setup(int ncpus) +{ + struct device_node *cpu; + u32 *tbprop = NULL; + int i; + + core99_tb_gpio = KL_GPIO_TB_ENABLE; /* default value */ + cpu = of_find_node_by_type(NULL, "cpu"); + if (cpu != NULL) { + tbprop = (u32 *)get_property(cpu, "timebase-enable", NULL); + if (tbprop) + core99_tb_gpio = *tbprop; + of_node_put(cpu); + } + + /* XXX should get this from reg properties */ + for (i = 1; i < ncpus; ++i) + smp_hw_index[i] = i; + powersave_nap = 0; +} +#endif + +static int __init smp_core99_probe(void) +{ + struct device_node *cpus; + int ncpus = 0; + + if (ppc_md.progress) ppc_md.progress("smp_core99_probe", 0x345); + + /* Count CPUs in the device-tree */ + for (cpus = NULL; (cpus = of_find_node_by_type(cpus, "cpu")) != NULL;) + ++ncpus; + + printk(KERN_INFO "PowerMac SMP probe found %d cpus\n", ncpus); + + /* Nothing more to do if less than 2 of them */ + if (ncpus <= 1) + return 1; + + smp_core99_setup(ncpus); + mpic_request_ipis(); + core99_init_caches(0); + + return ncpus; +} + +static void __devinit smp_core99_kick_cpu(int nr) +{ + unsigned int save_vector; + unsigned long new_vector; + unsigned long flags; + volatile unsigned int *vector + = ((volatile unsigned int *)(KERNELBASE+0x100)); + + if (nr < 0 || nr > 3) + return; + if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu", 0x346); + + local_irq_save(flags); + local_irq_disable(); + + /* Save reset vector */ + save_vector = *vector; + + /* Setup fake reset vector that does + * b __secondary_start_pmac_0 + nr*8 - KERNELBASE + */ + new_vector = (unsigned long) __secondary_start_pmac_0 + nr * 8; + *vector = 0x48000002 + new_vector - KERNELBASE; + + /* flush data cache and inval instruction cache */ + flush_icache_range((unsigned long) vector, (unsigned long) vector + 4); + + /* Put some life in our friend */ + pmac_call_feature(PMAC_FTR_RESET_CPU, NULL, nr, 0); + + /* FIXME: We wait a bit for the CPU to take the exception, I should + * instead wait for the entry code to set something for me. Well, + * ideally, all that crap will be done in prom.c and the CPU left + * in a RAM-based wait loop like CHRP. + */ + mdelay(1); + + /* Restore our exception vector */ + *vector = save_vector; + flush_icache_range((unsigned long) vector, (unsigned long) vector + 4); + + local_irq_restore(flags); + if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu done", 0x347); +} + +static void __devinit smp_core99_setup_cpu(int cpu_nr) +{ + /* Setup L2/L3 */ + if (cpu_nr != 0) + core99_init_caches(cpu_nr); + + /* Setup openpic */ + mpic_setup_this_cpu(); + + if (cpu_nr == 0) { +#ifdef CONFIG_POWER4 + extern void g5_phy_disable_cpu1(void); + + /* If we didn't start the second CPU, we must take + * it off the bus + */ + if (machine_is_compatible("MacRISC4") && + num_online_cpus() < 2) + g5_phy_disable_cpu1(); +#endif /* CONFIG_POWER4 */ + if (ppc_md.progress) ppc_md.progress("core99_setup_cpu 0 done", 0x349); + } +} + + +#if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32) + +int smp_core99_cpu_disable(void) +{ + cpu_clear(smp_processor_id(), cpu_online_map); + + /* XXX reset cpu affinity here */ + mpic_cpu_set_priority(0xf); + asm volatile("mtdec %0" : : "r" (0x7fffffff)); + mb(); + udelay(20); + asm volatile("mtdec %0" : : "r" (0x7fffffff)); + return 0; +} + +extern void low_cpu_die(void) __attribute__((noreturn)); /* in sleep.S */ +static int cpu_dead[NR_CPUS]; + +void cpu_die(void) +{ + local_irq_disable(); + cpu_dead[smp_processor_id()] = 1; + mb(); + low_cpu_die(); +} + +void smp_core99_cpu_die(unsigned int cpu) +{ + int timeout; + + timeout = 1000; + while (!cpu_dead[cpu]) { + if (--timeout == 0) { + printk("CPU %u refused to die!\n", cpu); + break; + } + msleep(1); + } + cpu_dead[cpu] = 0; +} + +#endif + +/* Core99 Macs (dual G4s and G5s) */ +struct smp_ops_t core99_smp_ops = { + .message_pass = smp_mpic_message_pass, + .probe = smp_core99_probe, + .kick_cpu = smp_core99_kick_cpu, + .setup_cpu = smp_core99_setup_cpu, + .give_timebase = smp_core99_give_timebase, + .take_timebase = smp_core99_take_timebase, +#if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32) + .cpu_disable = smp_core99_cpu_disable, + .cpu_die = smp_core99_cpu_die, +#endif +}; |