diff options
Diffstat (limited to 'arch/powerpc/platforms/powernv/eeh-ioda.c')
-rw-r--r-- | arch/powerpc/platforms/powernv/eeh-ioda.c | 349 |
1 files changed, 195 insertions, 154 deletions
diff --git a/arch/powerpc/platforms/powernv/eeh-ioda.c b/arch/powerpc/platforms/powernv/eeh-ioda.c index 5b51079f3e3..8ad0c5b891f 100644 --- a/arch/powerpc/platforms/powernv/eeh-ioda.c +++ b/arch/powerpc/platforms/powernv/eeh-ioda.c @@ -42,11 +42,19 @@ static int ioda_eeh_event(struct notifier_block *nb, { uint64_t changed_evts = (uint64_t)change; - /* We simply send special EEH event */ - if ((changed_evts & OPAL_EVENT_PCI_ERROR) && - (events & OPAL_EVENT_PCI_ERROR) && - eeh_enabled()) + /* + * We simply send special EEH event if EEH has + * been enabled, or clear pending events in + * case that we enable EEH soon + */ + if (!(changed_evts & OPAL_EVENT_PCI_ERROR) || + !(events & OPAL_EVENT_PCI_ERROR)) + return 0; + + if (eeh_enabled()) eeh_send_failure_event(NULL); + else + opal_notifier_update_evt(OPAL_EVENT_PCI_ERROR, 0x0ul); return 0; } @@ -141,7 +149,9 @@ static int ioda_eeh_post_init(struct pci_controller *hose) } #ifdef CONFIG_DEBUG_FS - if (phb->dbgfs) { + if (!phb->has_dbgfs && phb->dbgfs) { + phb->has_dbgfs = 1; + debugfs_create_file("err_injct_outbound", 0600, phb->dbgfs, hose, &ioda_eeh_outb_dbgfs_ops); @@ -154,7 +164,14 @@ static int ioda_eeh_post_init(struct pci_controller *hose) } #endif - phb->eeh_state |= PNV_EEH_STATE_ENABLED; + /* If EEH is enabled, we're going to rely on that. + * Otherwise, we restore to conventional mechanism + * to clear frozen PE during PCI config access. + */ + if (eeh_enabled()) + phb->flags |= PNV_PHB_FLAG_EEH; + else + phb->flags &= ~PNV_PHB_FLAG_EEH; return 0; } @@ -250,7 +267,7 @@ static int ioda_eeh_get_state(struct eeh_pe *pe) { s64 ret = 0; u8 fstate; - u16 pcierr; + __be16 pcierr; u32 pe_no; int result; struct pci_controller *hose = pe->phb; @@ -268,6 +285,21 @@ static int ioda_eeh_get_state(struct eeh_pe *pe) return EEH_STATE_NOT_SUPPORT; } + /* + * If we're in middle of PE reset, return normal + * state to keep EEH core going. For PHB reset, we + * still expect to have fenced PHB cleared with + * PHB reset. + */ + if (!(pe->type & EEH_PE_PHB) && + (pe->state & EEH_PE_RESET)) { + result = (EEH_STATE_MMIO_ACTIVE | + EEH_STATE_DMA_ACTIVE | + EEH_STATE_MMIO_ENABLED | + EEH_STATE_DMA_ENABLED); + return result; + } + /* Retrieve PE status through OPAL */ pe_no = pe->addr; ret = opal_pci_eeh_freeze_status(phb->opal_id, pe_no, @@ -284,7 +316,7 @@ static int ioda_eeh_get_state(struct eeh_pe *pe) result = 0; result &= ~EEH_STATE_RESET_ACTIVE; - if (pcierr != OPAL_EEH_PHB_ERROR) { + if (be16_to_cpu(pcierr) != OPAL_EEH_PHB_ERROR) { result |= EEH_STATE_MMIO_ACTIVE; result |= EEH_STATE_DMA_ACTIVE; result |= EEH_STATE_MMIO_ENABLED; @@ -347,52 +379,6 @@ static int ioda_eeh_get_state(struct eeh_pe *pe) return result; } -static int ioda_eeh_pe_clear(struct eeh_pe *pe) -{ - struct pci_controller *hose; - struct pnv_phb *phb; - u32 pe_no; - u8 fstate; - u16 pcierr; - s64 ret; - - pe_no = pe->addr; - hose = pe->phb; - phb = pe->phb->private_data; - - /* Clear the EEH error on the PE */ - ret = opal_pci_eeh_freeze_clear(phb->opal_id, - pe_no, OPAL_EEH_ACTION_CLEAR_FREEZE_ALL); - if (ret) { - pr_err("%s: Failed to clear EEH error for " - "PHB#%x-PE#%x, err=%lld\n", - __func__, hose->global_number, pe_no, ret); - return -EIO; - } - - /* - * Read the PE state back and verify that the frozen - * state has been removed. - */ - ret = opal_pci_eeh_freeze_status(phb->opal_id, pe_no, - &fstate, &pcierr, NULL); - if (ret) { - pr_err("%s: Failed to get EEH status on " - "PHB#%x-PE#%x\n, err=%lld\n", - __func__, hose->global_number, pe_no, ret); - return -EIO; - } - - if (fstate != OPAL_EEH_STOPPED_NOT_FROZEN) { - pr_err("%s: Frozen state not cleared on " - "PHB#%x-PE#%x, sts=%x\n", - __func__, hose->global_number, pe_no, fstate); - return -EIO; - } - - return 0; -} - static s64 ioda_eeh_phb_poll(struct pnv_phb *phb) { s64 rc = OPAL_HARDWARE; @@ -402,13 +388,16 @@ static s64 ioda_eeh_phb_poll(struct pnv_phb *phb) if (rc <= 0) break; - msleep(rc); + if (system_state < SYSTEM_RUNNING) + udelay(1000 * rc); + else + msleep(rc); } return rc; } -static int ioda_eeh_phb_reset(struct pci_controller *hose, int option) +int ioda_eeh_phb_reset(struct pci_controller *hose, int option) { struct pnv_phb *phb = hose->private_data; s64 rc = OPAL_HARDWARE; @@ -431,9 +420,17 @@ static int ioda_eeh_phb_reset(struct pci_controller *hose, int option) /* * Poll state of the PHB until the request is done - * successfully. + * successfully. The PHB reset is usually PHB complete + * reset followed by hot reset on root bus. So we also + * need the PCI bus settlement delay. */ rc = ioda_eeh_phb_poll(phb); + if (option == EEH_RESET_DEACTIVATE) { + if (system_state < SYSTEM_RUNNING) + udelay(1000 * EEH_PE_RST_SETTLE_TIME); + else + msleep(EEH_PE_RST_SETTLE_TIME); + } out: if (rc != OPAL_SUCCESS) return -EIO; @@ -471,6 +468,8 @@ static int ioda_eeh_root_reset(struct pci_controller *hose, int option) /* Poll state of the PHB until the request is done */ rc = ioda_eeh_phb_poll(phb); + if (option == EEH_RESET_DEACTIVATE) + msleep(EEH_PE_RST_SETTLE_TIME); out: if (rc != OPAL_SUCCESS) return -EIO; @@ -478,32 +477,71 @@ out: return 0; } -static int ioda_eeh_bridge_reset(struct pci_controller *hose, - struct pci_dev *dev, int option) +static int ioda_eeh_bridge_reset(struct pci_dev *dev, int option) + { - u16 ctrl; + struct device_node *dn = pci_device_to_OF_node(dev); + struct eeh_dev *edev = of_node_to_eeh_dev(dn); + int aer = edev ? edev->aer_cap : 0; + u32 ctrl; - pr_debug("%s: Reset device %04x:%02x:%02x.%01x with option %d\n", - __func__, hose->global_number, dev->bus->number, - PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn), option); + pr_debug("%s: Reset PCI bus %04x:%02x with option %d\n", + __func__, pci_domain_nr(dev->bus), + dev->bus->number, option); switch (option) { case EEH_RESET_FUNDAMENTAL: case EEH_RESET_HOT: - pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &ctrl); + /* Don't report linkDown event */ + if (aer) { + eeh_ops->read_config(dn, aer + PCI_ERR_UNCOR_MASK, + 4, &ctrl); + ctrl |= PCI_ERR_UNC_SURPDN; + eeh_ops->write_config(dn, aer + PCI_ERR_UNCOR_MASK, + 4, ctrl); + } + + eeh_ops->read_config(dn, PCI_BRIDGE_CONTROL, 2, &ctrl); ctrl |= PCI_BRIDGE_CTL_BUS_RESET; - pci_write_config_word(dev, PCI_BRIDGE_CONTROL, ctrl); + eeh_ops->write_config(dn, PCI_BRIDGE_CONTROL, 2, ctrl); + msleep(EEH_PE_RST_HOLD_TIME); + break; case EEH_RESET_DEACTIVATE: - pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &ctrl); + eeh_ops->read_config(dn, PCI_BRIDGE_CONTROL, 2, &ctrl); ctrl &= ~PCI_BRIDGE_CTL_BUS_RESET; - pci_write_config_word(dev, PCI_BRIDGE_CONTROL, ctrl); + eeh_ops->write_config(dn, PCI_BRIDGE_CONTROL, 2, ctrl); + msleep(EEH_PE_RST_SETTLE_TIME); + + /* Continue reporting linkDown event */ + if (aer) { + eeh_ops->read_config(dn, aer + PCI_ERR_UNCOR_MASK, + 4, &ctrl); + ctrl &= ~PCI_ERR_UNC_SURPDN; + eeh_ops->write_config(dn, aer + PCI_ERR_UNCOR_MASK, + 4, ctrl); + } + break; } return 0; } +void pnv_pci_reset_secondary_bus(struct pci_dev *dev) +{ + struct pci_controller *hose; + + if (pci_is_root_bus(dev->bus)) { + hose = pci_bus_to_host(dev->bus); + ioda_eeh_root_reset(hose, EEH_RESET_HOT); + ioda_eeh_root_reset(hose, EEH_RESET_DEACTIVATE); + } else { + ioda_eeh_bridge_reset(dev, EEH_RESET_HOT); + ioda_eeh_bridge_reset(dev, EEH_RESET_DEACTIVATE); + } +} + /** * ioda_eeh_reset - Reset the indicated PE * @pe: EEH PE @@ -523,27 +561,18 @@ static int ioda_eeh_reset(struct eeh_pe *pe, int option) int ret; /* - * Anyway, we have to clear the problematic state for the - * corresponding PE. However, we needn't do it if the PE - * is PHB associated. That means the PHB is having fatal - * errors and it needs reset. Further more, the AIB interface - * isn't reliable any more. - */ - if (!(pe->type & EEH_PE_PHB) && - (option == EEH_RESET_HOT || - option == EEH_RESET_FUNDAMENTAL)) { - ret = ioda_eeh_pe_clear(pe); - if (ret) - return -EIO; - } - - /* - * The rules applied to reset, either fundamental or hot reset: + * For PHB reset, we always have complete reset. For those PEs whose + * primary bus derived from root complex (root bus) or root port + * (usually bus#1), we apply hot or fundamental reset on the root port. + * For other PEs, we always have hot reset on the PE primary bus. * - * We always reset the direct upstream bridge of the PE. If the - * direct upstream bridge isn't root bridge, we always take hot - * reset no matter what option (fundamental or hot) is. Otherwise, - * we should do the reset according to the required option. + * Here, we have different design to pHyp, which always clear the + * frozen state during PE reset. However, the good idea here from + * benh is to keep frozen state before we get PE reset done completely + * (until BAR restore). With the frozen state, HW drops illegal IO + * or MMIO access, which can incur recrusive frozen PE during PE + * reset. The side effect is that EEH core has to clear the frozen + * state explicitly after BAR restore. */ if (pe->type & EEH_PE_PHB) { ret = ioda_eeh_phb_reset(hose, option); @@ -553,7 +582,7 @@ static int ioda_eeh_reset(struct eeh_pe *pe, int option) pci_is_root_bus(bus->parent)) ret = ioda_eeh_root_reset(hose, option); else - ret = ioda_eeh_bridge_reset(hose, bus->self, option); + ret = ioda_eeh_bridge_reset(bus->self, option); } return ret; @@ -640,22 +669,6 @@ static void ioda_eeh_hub_diag(struct pci_controller *hose) } } -static int ioda_eeh_get_phb_pe(struct pci_controller *hose, - struct eeh_pe **pe) -{ - struct eeh_pe *phb_pe; - - phb_pe = eeh_phb_pe_get(hose); - if (!phb_pe) { - pr_warning("%s Can't find PE for PHB#%d\n", - __func__, hose->global_number); - return -EEXIST; - } - - *pe = phb_pe; - return 0; -} - static int ioda_eeh_get_pe(struct pci_controller *hose, u16 pe_no, struct eeh_pe **pe) { @@ -663,7 +676,8 @@ static int ioda_eeh_get_pe(struct pci_controller *hose, struct eeh_dev dev; /* Find the PHB PE */ - if (ioda_eeh_get_phb_pe(hose, &phb_pe)) + phb_pe = eeh_phb_pe_get(hose); + if (!phb_pe) return -EEXIST; /* Find the PE according to PE# */ @@ -691,26 +705,30 @@ static int ioda_eeh_next_error(struct eeh_pe **pe) { struct pci_controller *hose; struct pnv_phb *phb; - u64 frozen_pe_no; - u16 err_type, severity; + struct eeh_pe *phb_pe, *parent_pe; + __be64 frozen_pe_no; + __be16 err_type, severity; + int active_flags = (EEH_STATE_MMIO_ACTIVE | EEH_STATE_DMA_ACTIVE); long rc; - int ret = EEH_NEXT_ERR_NONE; + int state, ret = EEH_NEXT_ERR_NONE; /* * While running here, it's safe to purge the event queue. * And we should keep the cached OPAL notifier event sychronized * between the kernel and firmware. */ - eeh_remove_event(NULL); + eeh_remove_event(NULL, false); opal_notifier_update_evt(OPAL_EVENT_PCI_ERROR, 0x0ul); list_for_each_entry(hose, &hose_list, list_node) { /* * If the subordinate PCI buses of the PHB has been - * removed, we needn't take care of it any more. + * removed or is exactly under error recovery, we + * needn't take care of it any more. */ phb = hose->private_data; - if (phb->eeh_state & PNV_EEH_STATE_REMOVED) + phb_pe = eeh_phb_pe_get(hose); + if (!phb_pe || (phb_pe->state & EEH_PE_ISOLATED)) continue; rc = opal_pci_next_error(phb->opal_id, @@ -725,8 +743,8 @@ static int ioda_eeh_next_error(struct eeh_pe **pe) } /* If the PHB doesn't have error, stop processing */ - if (err_type == OPAL_EEH_NO_ERROR || - severity == OPAL_EEH_SEV_NO_ERROR) { + if (be16_to_cpu(err_type) == OPAL_EEH_NO_ERROR || + be16_to_cpu(severity) == OPAL_EEH_SEV_NO_ERROR) { pr_devel("%s: No error found on PHB#%x\n", __func__, hose->global_number); continue; @@ -738,20 +756,14 @@ static int ioda_eeh_next_error(struct eeh_pe **pe) * specific PHB. */ pr_devel("%s: Error (%d, %d, %llu) on PHB#%x\n", - __func__, err_type, severity, - frozen_pe_no, hose->global_number); - switch (err_type) { + __func__, be16_to_cpu(err_type), be16_to_cpu(severity), + be64_to_cpu(frozen_pe_no), hose->global_number); + switch (be16_to_cpu(err_type)) { case OPAL_EEH_IOC_ERROR: - if (severity == OPAL_EEH_SEV_IOC_DEAD) { - list_for_each_entry(hose, &hose_list, - list_node) { - phb = hose->private_data; - phb->eeh_state |= PNV_EEH_STATE_REMOVED; - } - + if (be16_to_cpu(severity) == OPAL_EEH_SEV_IOC_DEAD) { pr_err("EEH: dead IOC detected\n"); ret = EEH_NEXT_ERR_DEAD_IOC; - } else if (severity == OPAL_EEH_SEV_INF) { + } else if (be16_to_cpu(severity) == OPAL_EEH_SEV_INF) { pr_info("EEH: IOC informative error " "detected\n"); ioda_eeh_hub_diag(hose); @@ -760,25 +772,26 @@ static int ioda_eeh_next_error(struct eeh_pe **pe) break; case OPAL_EEH_PHB_ERROR: - if (severity == OPAL_EEH_SEV_PHB_DEAD) { - if (ioda_eeh_get_phb_pe(hose, pe)) - break; - - pr_err("EEH: dead PHB#%x detected\n", - hose->global_number); - phb->eeh_state |= PNV_EEH_STATE_REMOVED; + if (be16_to_cpu(severity) == OPAL_EEH_SEV_PHB_DEAD) { + *pe = phb_pe; + pr_err("EEH: dead PHB#%x detected, " + "location: %s\n", + hose->global_number, + eeh_pe_loc_get(phb_pe)); ret = EEH_NEXT_ERR_DEAD_PHB; - } else if (severity == OPAL_EEH_SEV_PHB_FENCED) { - if (ioda_eeh_get_phb_pe(hose, pe)) - break; - - pr_err("EEH: fenced PHB#%x detected\n", - hose->global_number); + } else if (be16_to_cpu(severity) == + OPAL_EEH_SEV_PHB_FENCED) { + *pe = phb_pe; + pr_err("EEH: Fenced PHB#%x detected, " + "location: %s\n", + hose->global_number, + eeh_pe_loc_get(phb_pe)); ret = EEH_NEXT_ERR_FENCED_PHB; - } else if (severity == OPAL_EEH_SEV_INF) { + } else if (be16_to_cpu(severity) == OPAL_EEH_SEV_INF) { pr_info("EEH: PHB#%x informative error " - "detected\n", - hose->global_number); + "detected, location: %s\n", + hose->global_number, + eeh_pe_loc_get(phb_pe)); ioda_eeh_phb_diag(hose); ret = EEH_NEXT_ERR_NONE; } @@ -786,30 +799,33 @@ static int ioda_eeh_next_error(struct eeh_pe **pe) break; case OPAL_EEH_PE_ERROR: /* - * If we can't find the corresponding PE, the - * PEEV / PEST would be messy. So we force an - * fenced PHB so that it can be recovered. + * If we can't find the corresponding PE, we + * just try to unfreeze. */ - if (ioda_eeh_get_pe(hose, frozen_pe_no, pe)) { - if (!ioda_eeh_get_phb_pe(hose, pe)) { - pr_err("EEH: Escalated fenced PHB#%x " - "detected for PE#%llx\n", - hose->global_number, - frozen_pe_no); - ret = EEH_NEXT_ERR_FENCED_PHB; - } else { - ret = EEH_NEXT_ERR_NONE; - } + if (ioda_eeh_get_pe(hose, + be64_to_cpu(frozen_pe_no), pe)) { + /* Try best to clear it */ + pr_info("EEH: Clear non-existing PHB#%x-PE#%llx\n", + hose->global_number, frozen_pe_no); + pr_info("EEH: PHB location: %s\n", + eeh_pe_loc_get(phb_pe)); + opal_pci_eeh_freeze_clear(phb->opal_id, frozen_pe_no, + OPAL_EEH_ACTION_CLEAR_FREEZE_ALL); + ret = EEH_NEXT_ERR_NONE; + } else if ((*pe)->state & EEH_PE_ISOLATED) { + ret = EEH_NEXT_ERR_NONE; } else { pr_err("EEH: Frozen PE#%x on PHB#%x detected\n", (*pe)->addr, (*pe)->phb->global_number); + pr_err("EEH: PE location: %s, PHB location: %s\n", + eeh_pe_loc_get(*pe), eeh_pe_loc_get(phb_pe)); ret = EEH_NEXT_ERR_FROZEN_PE; } break; default: pr_warn("%s: Unexpected error type %d\n", - __func__, err_type); + __func__, be16_to_cpu(err_type)); } /* @@ -827,6 +843,31 @@ static int ioda_eeh_next_error(struct eeh_pe **pe) } /* + * We probably have the frozen parent PE out there and + * we need have to handle frozen parent PE firstly. + */ + if (ret == EEH_NEXT_ERR_FROZEN_PE) { + parent_pe = (*pe)->parent; + while (parent_pe) { + /* Hit the ceiling ? */ + if (parent_pe->type & EEH_PE_PHB) + break; + + /* Frozen parent PE ? */ + state = ioda_eeh_get_state(parent_pe); + if (state > 0 && + (state & active_flags) != active_flags) + *pe = parent_pe; + + /* Next parent level */ + parent_pe = parent_pe->parent; + } + + /* We possibly migrate to another PE */ + eeh_pe_state_mark(*pe, EEH_PE_ISOLATED); + } + + /* * If we have no errors on the specific PHB or only * informative error there, we continue poking it. * Otherwise, we need actions to be taken by upper |