diff options
Diffstat (limited to 'arch/powerpc/sysdev/ppc4xx_pci.c')
| -rw-r--r-- | arch/powerpc/sysdev/ppc4xx_pci.c | 1528 |
1 files changed, 1528 insertions, 0 deletions
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c b/arch/powerpc/sysdev/ppc4xx_pci.c new file mode 100644 index 00000000000..5abfcd15748 --- /dev/null +++ b/arch/powerpc/sysdev/ppc4xx_pci.c @@ -0,0 +1,1528 @@ +/* + * PCI / PCI-X / PCI-Express support for 4xx parts + * + * Copyright 2007 Ben. Herrenschmidt <benh@kernel.crashing.org>, IBM Corp. + * + * Most PCI Express code is coming from Stefan Roese implementation for + * arch/ppc in the Denx tree, slightly reworked by me. + * + * Copyright 2007 DENX Software Engineering, Stefan Roese <sr@denx.de> + * + * Some of that comes itself from a previous implementation for 440SPE only + * by Roland Dreier: + * + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * Roland Dreier <rolandd@cisco.com> + * + */ + +#undef DEBUG + +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/of.h> +#include <linux/bootmem.h> +#include <linux/delay.h> + +#include <asm/io.h> +#include <asm/pci-bridge.h> +#include <asm/machdep.h> +#include <asm/dcr.h> +#include <asm/dcr-regs.h> + +#include "ppc4xx_pci.h" + +static int dma_offset_set; + +/* Move that to a useable header */ +extern unsigned long total_memory; + +#define U64_TO_U32_LOW(val) ((u32)((val) & 0x00000000ffffffffULL)) +#define U64_TO_U32_HIGH(val) ((u32)((val) >> 32)) + +#ifdef CONFIG_RESOURCES_64BIT +#define RES_TO_U32_LOW(val) U64_TO_U32_LOW(val) +#define RES_TO_U32_HIGH(val) U64_TO_U32_HIGH(val) +#else +#define RES_TO_U32_LOW(val) (val) +#define RES_TO_U32_HIGH(val) (0) +#endif + +static inline int ppc440spe_revA(void) +{ + /* Catch both 440SPe variants, with and without RAID6 support */ + if ((mfspr(SPRN_PVR) & 0xffefffff) == 0x53421890) + return 1; + else + return 0; +} + +static void fixup_ppc4xx_pci_bridge(struct pci_dev *dev) +{ + struct pci_controller *hose; + int i; + + if (dev->devfn != 0 || dev->bus->self != NULL) + return; + + hose = pci_bus_to_host(dev->bus); + if (hose == NULL) + return; + + if (!of_device_is_compatible(hose->dn, "ibm,plb-pciex") && + !of_device_is_compatible(hose->dn, "ibm,plb-pcix") && + !of_device_is_compatible(hose->dn, "ibm,plb-pci")) + return; + + /* Hide the PCI host BARs from the kernel as their content doesn't + * fit well in the resource management + */ + for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { + dev->resource[i].start = dev->resource[i].end = 0; + dev->resource[i].flags = 0; + } + + printk(KERN_INFO "PCI: Hiding 4xx host bridge resources %s\n", + pci_name(dev)); +} +DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, fixup_ppc4xx_pci_bridge); + +static int __init ppc4xx_parse_dma_ranges(struct pci_controller *hose, + void __iomem *reg, + struct resource *res) +{ + u64 size; + const u32 *ranges; + int rlen; + int pna = of_n_addr_cells(hose->dn); + int np = pna + 5; + + /* Default */ + res->start = 0; + res->end = size = 0x80000000; + res->flags = IORESOURCE_MEM | IORESOURCE_PREFETCH; + + /* Get dma-ranges property */ + ranges = of_get_property(hose->dn, "dma-ranges", &rlen); + if (ranges == NULL) + goto out; + + /* Walk it */ + while ((rlen -= np * 4) >= 0) { + u32 pci_space = ranges[0]; + u64 pci_addr = of_read_number(ranges + 1, 2); + u64 cpu_addr = of_translate_dma_address(hose->dn, ranges + 3); + size = of_read_number(ranges + pna + 3, 2); + ranges += np; + if (cpu_addr == OF_BAD_ADDR || size == 0) + continue; + + /* We only care about memory */ + if ((pci_space & 0x03000000) != 0x02000000) + continue; + + /* We currently only support memory at 0, and pci_addr + * within 32 bits space + */ + if (cpu_addr != 0 || pci_addr > 0xffffffff) { + printk(KERN_WARNING "%s: Ignored unsupported dma range" + " 0x%016llx...0x%016llx -> 0x%016llx\n", + hose->dn->full_name, + pci_addr, pci_addr + size - 1, cpu_addr); + continue; + } + + /* Check if not prefetchable */ + if (!(pci_space & 0x40000000)) + res->flags &= ~IORESOURCE_PREFETCH; + + + /* Use that */ + res->start = pci_addr; +#ifndef CONFIG_RESOURCES_64BIT + /* Beware of 32 bits resources */ + if ((pci_addr + size) > 0x100000000ull) + res->end = 0xffffffff; + else +#endif + res->end = res->start + size - 1; + break; + } + + /* We only support one global DMA offset */ + if (dma_offset_set && pci_dram_offset != res->start) { + printk(KERN_ERR "%s: dma-ranges(s) mismatch\n", + hose->dn->full_name); + return -ENXIO; + } + + /* Check that we can fit all of memory as we don't support + * DMA bounce buffers + */ + if (size < total_memory) { + printk(KERN_ERR "%s: dma-ranges too small " + "(size=%llx total_memory=%lx)\n", + hose->dn->full_name, size, total_memory); + return -ENXIO; + } + + /* Check we are a power of 2 size and that base is a multiple of size*/ + if (!is_power_of_2(size) || + (res->start & (size - 1)) != 0) { + printk(KERN_ERR "%s: dma-ranges unaligned\n", + hose->dn->full_name); + return -ENXIO; + } + + /* Check that we are fully contained within 32 bits space */ + if (res->end > 0xffffffff) { + printk(KERN_ERR "%s: dma-ranges outside of 32 bits space\n", + hose->dn->full_name); + return -ENXIO; + } + out: + dma_offset_set = 1; + pci_dram_offset = res->start; + + printk(KERN_INFO "4xx PCI DMA offset set to 0x%08lx\n", + pci_dram_offset); + return 0; +} + +/* + * 4xx PCI 2.x part + */ + +static void __init ppc4xx_configure_pci_PMMs(struct pci_controller *hose, + void __iomem *reg) +{ + u32 la, ma, pcila, pciha; + int i, j; + + /* Setup outbound memory windows */ + for (i = j = 0; i < 3; i++) { + struct resource *res = &hose->mem_resources[i]; + + /* we only care about memory windows */ + if (!(res->flags & IORESOURCE_MEM)) + continue; + if (j > 2) { + printk(KERN_WARNING "%s: Too many ranges\n", + hose->dn->full_name); + break; + } + + /* Calculate register values */ + la = res->start; + pciha = RES_TO_U32_HIGH(res->start - hose->pci_mem_offset); + pcila = RES_TO_U32_LOW(res->start - hose->pci_mem_offset); + + ma = res->end + 1 - res->start; + if (!is_power_of_2(ma) || ma < 0x1000 || ma > 0xffffffffu) { + printk(KERN_WARNING "%s: Resource out of range\n", + hose->dn->full_name); + continue; + } + ma = (0xffffffffu << ilog2(ma)) | 0x1; + if (res->flags & IORESOURCE_PREFETCH) + ma |= 0x2; + + /* Program register values */ + writel(la, reg + PCIL0_PMM0LA + (0x10 * j)); + writel(pcila, reg + PCIL0_PMM0PCILA + (0x10 * j)); + writel(pciha, reg + PCIL0_PMM0PCIHA + (0x10 * j)); + writel(ma, reg + PCIL0_PMM0MA + (0x10 * j)); + j++; + } +} + +static void __init ppc4xx_configure_pci_PTMs(struct pci_controller *hose, + void __iomem *reg, + const struct resource *res) +{ + resource_size_t size = res->end - res->start + 1; + u32 sa; + + /* Calculate window size */ + sa = (0xffffffffu << ilog2(size)) | 1; + sa |= 0x1; + + /* RAM is always at 0 local for now */ + writel(0, reg + PCIL0_PTM1LA); + writel(sa, reg + PCIL0_PTM1MS); + + /* Map on PCI side */ + early_write_config_dword(hose, hose->first_busno, 0, + PCI_BASE_ADDRESS_1, res->start); + early_write_config_dword(hose, hose->first_busno, 0, + PCI_BASE_ADDRESS_2, 0x00000000); + early_write_config_word(hose, hose->first_busno, 0, + PCI_COMMAND, 0x0006); +} + +static void __init ppc4xx_probe_pci_bridge(struct device_node *np) +{ + /* NYI */ + struct resource rsrc_cfg; + struct resource rsrc_reg; + struct resource dma_window; + struct pci_controller *hose = NULL; + void __iomem *reg = NULL; + const int *bus_range; + int primary = 0; + + /* Fetch config space registers address */ + if (of_address_to_resource(np, 0, &rsrc_cfg)) { + printk(KERN_ERR "%s:Can't get PCI config register base !", + np->full_name); + return; + } + /* Fetch host bridge internal registers address */ + if (of_address_to_resource(np, 3, &rsrc_reg)) { + printk(KERN_ERR "%s: Can't get PCI internal register base !", + np->full_name); + return; + } + + /* Check if primary bridge */ + if (of_get_property(np, "primary", NULL)) + primary = 1; + + /* Get bus range if any */ + bus_range = of_get_property(np, "bus-range", NULL); + + /* Map registers */ + reg = ioremap(rsrc_reg.start, rsrc_reg.end + 1 - rsrc_reg.start); + if (reg == NULL) { + printk(KERN_ERR "%s: Can't map registers !", np->full_name); + goto fail; + } + + /* Allocate the host controller data structure */ + hose = pcibios_alloc_controller(np); + if (!hose) + goto fail; + + hose->first_busno = bus_range ? bus_range[0] : 0x0; + hose->last_busno = bus_range ? bus_range[1] : 0xff; + + /* Setup config space */ + setup_indirect_pci(hose, rsrc_cfg.start, rsrc_cfg.start + 0x4, 0); + + /* Disable all windows */ + writel(0, reg + PCIL0_PMM0MA); + writel(0, reg + PCIL0_PMM1MA); + writel(0, reg + PCIL0_PMM2MA); + writel(0, reg + PCIL0_PTM1MS); + writel(0, reg + PCIL0_PTM2MS); + + /* Parse outbound mapping resources */ + pci_process_bridge_OF_ranges(hose, np, primary); + + /* Parse inbound mapping resources */ + if (ppc4xx_parse_dma_ranges(hose, reg, &dma_window) != 0) + goto fail; + + /* Configure outbound ranges POMs */ + ppc4xx_configure_pci_PMMs(hose, reg); + + /* Configure inbound ranges PIMs */ + ppc4xx_configure_pci_PTMs(hose, reg, &dma_window); + + /* We don't need the registers anymore */ + iounmap(reg); + return; + + fail: + if (hose) + pcibios_free_controller(hose); + if (reg) + iounmap(reg); +} + +/* + * 4xx PCI-X part + */ + +static void __init ppc4xx_configure_pcix_POMs(struct pci_controller *hose, + void __iomem *reg) +{ + u32 lah, lal, pciah, pcial, sa; + int i, j; + + /* Setup outbound memory windows */ + for (i = j = 0; i < 3; i++) { + struct resource *res = &hose->mem_resources[i]; + + /* we only care about memory windows */ + if (!(res->flags & IORESOURCE_MEM)) + continue; + if (j > 1) { + printk(KERN_WARNING "%s: Too many ranges\n", + hose->dn->full_name); + break; + } + + /* Calculate register values */ + lah = RES_TO_U32_HIGH(res->start); + lal = RES_TO_U32_LOW(res->start); + pciah = RES_TO_U32_HIGH(res->start - hose->pci_mem_offset); + pcial = RES_TO_U32_LOW(res->start - hose->pci_mem_offset); + sa = res->end + 1 - res->start; + if (!is_power_of_2(sa) || sa < 0x100000 || + sa > 0xffffffffu) { + printk(KERN_WARNING "%s: Resource out of range\n", + hose->dn->full_name); + continue; + } + sa = (0xffffffffu << ilog2(sa)) | 0x1; + + /* Program register values */ + if (j == 0) { + writel(lah, reg + PCIX0_POM0LAH); + writel(lal, reg + PCIX0_POM0LAL); + writel(pciah, reg + PCIX0_POM0PCIAH); + writel(pcial, reg + PCIX0_POM0PCIAL); + writel(sa, reg + PCIX0_POM0SA); + } else { + writel(lah, reg + PCIX0_POM1LAH); + writel(lal, reg + PCIX0_POM1LAL); + writel(pciah, reg + PCIX0_POM1PCIAH); + writel(pcial, reg + PCIX0_POM1PCIAL); + writel(sa, reg + PCIX0_POM1SA); + } + j++; + } +} + +static void __init ppc4xx_configure_pcix_PIMs(struct pci_controller *hose, + void __iomem *reg, + const struct resource *res, + int big_pim, + int enable_msi_hole) +{ + resource_size_t size = res->end - res->start + 1; + u32 sa; + + /* RAM is always at 0 */ + writel(0x00000000, reg + PCIX0_PIM0LAH); + writel(0x00000000, reg + PCIX0_PIM0LAL); + + /* Calculate window size */ + sa = (0xffffffffu << ilog2(size)) | 1; + sa |= 0x1; + if (res->flags & IORESOURCE_PREFETCH) + sa |= 0x2; + if (enable_msi_hole) + sa |= 0x4; + writel(sa, reg + PCIX0_PIM0SA); + if (big_pim) + writel(0xffffffff, reg + PCIX0_PIM0SAH); + + /* Map on PCI side */ + writel(0x00000000, reg + PCIX0_BAR0H); + writel(res->start, reg + PCIX0_BAR0L); + writew(0x0006, reg + PCIX0_COMMAND); +} + +static void __init ppc4xx_probe_pcix_bridge(struct device_node *np) +{ + struct resource rsrc_cfg; + struct resource rsrc_reg; + struct resource dma_window; + struct pci_controller *hose = NULL; + void __iomem *reg = NULL; + const int *bus_range; + int big_pim = 0, msi = 0, primary = 0; + + /* Fetch config space registers address */ + if (of_address_to_resource(np, 0, &rsrc_cfg)) { + printk(KERN_ERR "%s:Can't get PCI-X config register base !", + np->full_name); + return; + } + /* Fetch host bridge internal registers address */ + if (of_address_to_resource(np, 3, &rsrc_reg)) { + printk(KERN_ERR "%s: Can't get PCI-X internal register base !", + np->full_name); + return; + } + + /* Check if it supports large PIMs (440GX) */ + if (of_get_property(np, "large-inbound-windows", NULL)) + big_pim = 1; + + /* Check if we should enable MSIs inbound hole */ + if (of_get_property(np, "enable-msi-hole", NULL)) + msi = 1; + + /* Check if primary bridge */ + if (of_get_property(np, "primary", NULL)) + primary = 1; + + /* Get bus range if any */ + bus_range = of_get_property(np, "bus-range", NULL); + + /* Map registers */ + reg = ioremap(rsrc_reg.start, rsrc_reg.end + 1 - rsrc_reg.start); + if (reg == NULL) { + printk(KERN_ERR "%s: Can't map registers !", np->full_name); + goto fail; + } + + /* Allocate the host controller data structure */ + hose = pcibios_alloc_controller(np); + if (!hose) + goto fail; + + hose->first_busno = bus_range ? bus_range[0] : 0x0; + hose->last_busno = bus_range ? bus_range[1] : 0xff; + + /* Setup config space */ + setup_indirect_pci(hose, rsrc_cfg.start, rsrc_cfg.start + 0x4, 0); + + /* Disable all windows */ + writel(0, reg + PCIX0_POM0SA); + writel(0, reg + PCIX0_POM1SA); + writel(0, reg + PCIX0_POM2SA); + writel(0, reg + PCIX0_PIM0SA); + writel(0, reg + PCIX0_PIM1SA); + writel(0, reg + PCIX0_PIM2SA); + if (big_pim) { + writel(0, reg + PCIX0_PIM0SAH); + writel(0, reg + PCIX0_PIM2SAH); + } + + /* Parse outbound mapping resources */ + pci_process_bridge_OF_ranges(hose, np, primary); + + /* Parse inbound mapping resources */ + if (ppc4xx_parse_dma_ranges(hose, reg, &dma_window) != 0) + goto fail; + + /* Configure outbound ranges POMs */ + ppc4xx_configure_pcix_POMs(hose, reg); + + /* Configure inbound ranges PIMs */ + ppc4xx_configure_pcix_PIMs(hose, reg, &dma_window, big_pim, msi); + + /* We don't need the registers anymore */ + iounmap(reg); + return; + + fail: + if (hose) + pcibios_free_controller(hose); + if (reg) + iounmap(reg); +} + +#ifdef CONFIG_PPC4xx_PCI_EXPRESS + +/* + * 4xx PCI-Express part + * + * We support 3 parts currently based on the compatible property: + * + * ibm,plb-pciex-440spe + * ibm,plb-pciex-405ex + * + * Anything else will be rejected for now as they are all subtly + * different unfortunately. + * + */ + +#define MAX_PCIE_BUS_MAPPED 0x40 + +struct ppc4xx_pciex_port +{ + struct pci_controller *hose; + struct device_node *node; + unsigned int index; + int endpoint; + int link; + int has_ibpre; + unsigned int sdr_base; + dcr_host_t dcrs; + struct resource cfg_space; + struct resource utl_regs; + void __iomem *utl_base; +}; + +static struct ppc4xx_pciex_port *ppc4xx_pciex_ports; +static unsigned int ppc4xx_pciex_port_count; + +struct ppc4xx_pciex_hwops +{ + int (*core_init)(struct device_node *np); + int (*port_init_hw)(struct ppc4xx_pciex_port *port); + int (*setup_utl)(struct ppc4xx_pciex_port *port); +}; + +static struct ppc4xx_pciex_hwops *ppc4xx_pciex_hwops; + +#ifdef CONFIG_44x + +/* Check various reset bits of the 440SPe PCIe core */ +static int __init ppc440spe_pciex_check_reset(struct device_node *np) +{ + u32 valPE0, valPE1, valPE2; + int err = 0; + + /* SDR0_PEGPLLLCT1 reset */ + if (!(mfdcri(SDR0, PESDR0_PLLLCT1) & 0x01000000)) { + /* + * the PCIe core was probably already initialised + * by firmware - let's re-reset RCSSET regs + * + * -- Shouldn't we also re-reset the whole thing ? -- BenH + */ + pr_debug("PCIE: SDR0_PLLLCT1 already reset.\n"); + mtdcri(SDR0, PESDR0_440SPE_RCSSET, 0x01010000); + mtdcri(SDR0, PESDR1_440SPE_RCSSET, 0x01010000); + mtdcri(SDR0, PESDR2_440SPE_RCSSET, 0x01010000); + } + + valPE0 = mfdcri(SDR0, PESDR0_440SPE_RCSSET); + valPE1 = mfdcri(SDR0, PESDR1_440SPE_RCSSET); + valPE2 = mfdcri(SDR0, PESDR2_440SPE_RCSSET); + + /* SDR0_PExRCSSET rstgu */ + if (!(valPE0 & 0x01000000) || + !(valPE1 & 0x01000000) || + !(valPE2 & 0x01000000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rstgu error\n"); + err = -1; + } + + /* SDR0_PExRCSSET rstdl */ + if (!(valPE0 & 0x00010000) || + !(valPE1 & 0x00010000) || + !(valPE2 & 0x00010000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rstdl error\n"); + err = -1; + } + + /* SDR0_PExRCSSET rstpyn */ + if ((valPE0 & 0x00001000) || + (valPE1 & 0x00001000) || + (valPE2 & 0x00001000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rstpyn error\n"); + err = -1; + } + + /* SDR0_PExRCSSET hldplb */ + if ((valPE0 & 0x10000000) || + (valPE1 & 0x10000000) || + (valPE2 & 0x10000000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET hldplb error\n"); + err = -1; + } + + /* SDR0_PExRCSSET rdy */ + if ((valPE0 & 0x00100000) || + (valPE1 & 0x00100000) || + (valPE2 & 0x00100000)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET rdy error\n"); + err = -1; + } + + /* SDR0_PExRCSSET shutdown */ + if ((valPE0 & 0x00000100) || + (valPE1 & 0x00000100) || + (valPE2 & 0x00000100)) { + printk(KERN_INFO "PCIE: SDR0_PExRCSSET shutdown error\n"); + err = -1; + } + + return err; +} + +/* Global PCIe core initializations for 440SPe core */ +static int __init ppc440spe_pciex_core_init(struct device_node *np) +{ + int time_out = 20; + + /* Set PLL clock receiver to LVPECL */ + mtdcri(SDR0, PESDR0_PLLLCT1, mfdcri(SDR0, PESDR0_PLLLCT1) | 1 << 28); + + /* Shouldn't we do all the calibration stuff etc... here ? */ + if (ppc440spe_pciex_check_reset(np)) + return -ENXIO; + + if (!(mfdcri(SDR0, PESDR0_PLLLCT2) & 0x10000)) { + printk(KERN_INFO "PCIE: PESDR_PLLCT2 resistance calibration " + "failed (0x%08x)\n", + mfdcri(SDR0, PESDR0_PLLLCT2)); + return -1; + } + + /* De-assert reset of PCIe PLL, wait for lock */ + mtdcri(SDR0, PESDR0_PLLLCT1, + mfdcri(SDR0, PESDR0_PLLLCT1) & ~(1 << 24)); + udelay(3); + + while (time_out) { + if (!(mfdcri(SDR0, PESDR0_PLLLCT3) & 0x10000000)) { + time_out--; + udelay(1); + } else + break; + } + if (!time_out) { + printk(KERN_INFO "PCIE: VCO output not locked\n"); + return -1; + } + + pr_debug("PCIE initialization OK\n"); + + return 3; +} + +static int ppc440spe_pciex_init_port_hw(struct ppc4xx_pciex_port *port) +{ + u32 val = 1 << 24; + + if (port->endpoint) + val = PTYPE_LEGACY_ENDPOINT << 20; + else + val = PTYPE_ROOT_PORT << 20; + + if (port->index == 0) + val |= LNKW_X8 << 12; + else + val |= LNKW_X4 << 12; + + mtdcri(SDR0, port->sdr_base + PESDRn_DLPSET, val); + mtdcri(SDR0, port->sdr_base + PESDRn_UTLSET1, 0x20222222); + if (ppc440spe_revA()) + mtdcri(SDR0, port->sdr_base + PESDRn_UTLSET2, 0x11000000); + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL0SET1, 0x35000000); + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL1SET1, 0x35000000); + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL2SET1, 0x35000000); + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL3SET1, 0x35000000); + if (port->index == 0) { + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL4SET1, + 0x35000000); + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL5SET1, + 0x35000000); + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL6SET1, + 0x35000000); + mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL7SET1, + 0x35000000); + } + val = mfdcri(SDR0, port->sdr_base + PESDRn_RCSSET); + mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET, + (val & ~(1 << 24 | 1 << 16)) | 1 << 12); + + return 0; +} + +static int ppc440speA_pciex_init_port_hw(struct ppc4xx_pciex_port *port) +{ + return ppc440spe_pciex_init_port_hw(port); +} + +static int ppc440speB_pciex_init_port_hw(struct ppc4xx_pciex_port *port) +{ + int rc = ppc440spe_pciex_init_port_hw(port); + + port->has_ibpre = 1; + + return rc; +} + +static int ppc440speA_pciex_init_utl(struct ppc4xx_pciex_port *port) +{ + /* XXX Check what that value means... I hate magic */ + dcr_write(port->dcrs, DCRO_PEGPL_SPECIAL, 0x68782800); + + /* + * Set buffer allocations and then assert VRB and TXE. + */ + out_be32(port->utl_base + PEUTL_OUTTR, 0x08000000); + out_be32(port->utl_base + PEUTL_INTR, 0x02000000); + out_be32(port->utl_base + PEUTL_OPDBSZ, 0x10000000); + out_be32(port->utl_base + PEUTL_PBBSZ, 0x53000000); + out_be32(port->utl_base + PEUTL_IPHBSZ, 0x08000000); + out_be32(port->utl_base + PEUTL_IPDBSZ, 0x10000000); + out_be32(port->utl_base + PEUTL_RCIRQEN, 0x00f00000); + out_be32(port->utl_base + PEUTL_PCTL, 0x80800066); + + return 0; +} + +static int ppc440speB_pciex_init_utl(struct ppc4xx_pciex_port *port) +{ + /* Report CRS to the operating system */ + out_be32(port->utl_base + PEUTL_PBCTL, 0x08000000); + + return 0; +} + +static struct ppc4xx_pciex_hwops ppc440speA_pcie_hwops __initdata = +{ + .core_init = ppc440spe_pciex_core_init, + .port_init_hw = ppc440speA_pciex_init_port_hw, + .setup_utl = ppc440speA_pciex_init_utl, +}; + +static struct ppc4xx_pciex_hwops ppc440speB_pcie_hwops __initdata = +{ + .core_init = ppc440spe_pciex_core_init, + .port_init_hw = ppc440speB_pciex_init_port_hw, + .setup_utl = ppc440speB_pciex_init_utl, +}; + +#endif /* CONFIG_44x */ + +#ifdef CONFIG_40x + +static int __init ppc405ex_pciex_core_init(struct device_node *np) +{ + /* Nothing to do, return 2 ports */ + return 2; +} + +static void ppc405ex_pcie_phy_reset(struct ppc4xx_pciex_port *port) +{ + /* Assert the PE0_PHY reset */ + mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET, 0x01010000); + msleep(1); + + /* deassert the PE0_hotreset */ + if (port->endpoint) + mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET, 0x01111000); + else + mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET, 0x01101000); + + /* poll for phy !reset */ + /* XXX FIXME add timeout */ + while (!(mfdcri(SDR0, port->sdr_base + PESDRn_405EX_PHYSTA) & 0x00001000)) + ; + + /* deassert the PE0_gpl_utl_reset */ + mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET, 0x00101000); +} + +static int ppc405ex_pciex_init_port_hw(struct ppc4xx_pciex_port *port) +{ + u32 val; + + if (port->endpoint) + val = PTYPE_LEGACY_ENDPOINT; + else + val = PTYPE_ROOT_PORT; + + mtdcri(SDR0, port->sdr_base + PESDRn_DLPSET, + 1 << 24 | val << 20 | LNKW_X1 << 12); + + mtdcri(SDR0, port->sdr_base + PESDRn_UTLSET1, 0x00000000); + mtdcri(SDR0, port->sdr_base + PESDRn_UTLSET2, 0x01010000); + mtdcri(SDR0, port->sdr_base + PESDRn_405EX_PHYSET1, 0x720F0000); + mtdcri(SDR0, port->sdr_base + PESDRn_405EX_PHYSET2, 0x70600003); + + /* + * Only reset the PHY when no link is currently established. + * This is for the Atheros PCIe board which has problems to establish + * the link (again) after this PHY reset. All other currently tested + * PCIe boards don't show this problem. + * This has to be re-tested and fixed in a later release! + */ +#if 0 /* XXX FIXME: Not resetting the PHY will leave all resources + * configured as done previously by U-Boot. Then Linux will currently + * not reassign them. So the PHY reset is now done always. This will + * lead to problems with the Atheros PCIe board again. + */ + val = mfdcri(SDR0, port->sdr_base + PESDRn_LOOP); + if (!(val & 0x00001000)) + ppc405ex_pcie_phy_reset(port); +#else + ppc405ex_pcie_phy_reset(port); +#endif + + dcr_write(port->dcrs, DCRO_PEGPL_CFG, 0x10000000); /* guarded on */ + + port->has_ibpre = 1; + + return 0; +} + +static int ppc405ex_pciex_init_utl(struct ppc4xx_pciex_port *port) +{ + dcr_write(port->dcrs, DCRO_PEGPL_SPECIAL, 0x0); + + /* + * Set buffer allocations and then assert VRB and TXE. + */ + out_be32(port->utl_base + PEUTL_OUTTR, 0x02000000); + out_be32(port->utl_base + PEUTL_INTR, 0x02000000); + out_be32(port->utl_base + PEUTL_OPDBSZ, 0x04000000); + out_be32(port->utl_base + PEUTL_PBBSZ, 0x21000000); + out_be32(port->utl_base + PEUTL_IPHBSZ, 0x02000000); + out_be32(port->utl_base + PEUTL_IPDBSZ, 0x04000000); + out_be32(port->utl_base + PEUTL_RCIRQEN, 0x00f00000); + out_be32(port->utl_base + PEUTL_PCTL, 0x80800066); + + out_be32(port->utl_base + PEUTL_PBCTL, 0x08000000); + + return 0; +} + +static struct ppc4xx_pciex_hwops ppc405ex_pcie_hwops __initdata = +{ + .core_init = ppc405ex_pciex_core_init, + .port_init_hw = ppc405ex_pciex_init_port_hw, + .setup_utl = ppc405ex_pciex_init_utl, +}; + +#endif /* CONFIG_40x */ + + +/* Check that the core has been initied and if not, do it */ +static int __init ppc4xx_pciex_check_core_init(struct device_node *np) +{ + static int core_init; + int count = -ENODEV; + + if (core_init++) + return 0; + +#ifdef CONFIG_44x + if (of_device_is_compatible(np, "ibm,plb-pciex-440spe")) { + if (ppc440spe_revA()) + ppc4xx_pciex_hwops = &ppc440speA_pcie_hwops; + else + ppc4xx_pciex_hwops = &ppc440speB_pcie_hwops; + } +#endif /* CONFIG_44x */ +#ifdef CONFIG_40x + if (of_device_is_compatible(np, "ibm,plb-pciex-405ex")) + ppc4xx_pciex_hwops = &ppc405ex_pcie_hwops; +#endif + if (ppc4xx_pciex_hwops == NULL) { + printk(KERN_WARNING "PCIE: unknown host type %s\n", + np->full_name); + return -ENODEV; + } + + count = ppc4xx_pciex_hwops->core_init(np); + if (count > 0) { + ppc4xx_pciex_ports = + kzalloc(count * sizeof(struct ppc4xx_pciex_port), + GFP_KERNEL); + if (ppc4xx_pciex_ports) { + ppc4xx_pciex_port_count = count; + return 0; + } + printk(KERN_WARNING "PCIE: failed to allocate ports array\n"); + return -ENOMEM; + } + return -ENODEV; +} + +static void __init ppc4xx_pciex_port_init_mapping(struct ppc4xx_pciex_port *port) +{ + /* We map PCI Express configuration based on the reg property */ + dcr_write(port->dcrs, DCRO_PEGPL_CFGBAH, + RES_TO_U32_HIGH(port->cfg_space.start)); + dcr_write(port->dcrs, DCRO_PEGPL_CFGBAL, + RES_TO_U32_LOW(port->cfg_space.start)); + + /* XXX FIXME: Use size from reg property. For now, map 512M */ + dcr_write(port->dcrs, DCRO_PEGPL_CFGMSK, 0xe0000001); + + /* We map UTL registers based on the reg property */ + dcr_write(port->dcrs, DCRO_PEGPL_REGBAH, + RES_TO_U32_HIGH(port->utl_regs.start)); + dcr_write(port->dcrs, DCRO_PEGPL_REGBAL, + RES_TO_U32_LOW(port->utl_regs.start)); + + /* XXX FIXME: Use size from reg property */ + dcr_write(port->dcrs, DCRO_PEGPL_REGMSK, 0x00007001); + + /* Disable all other outbound windows */ + dcr_write(port->dcrs, DCRO_PEGPL_OMR1MSKL, 0); + dcr_write(port->dcrs, DCRO_PEGPL_OMR2MSKL, 0); + dcr_write(port->dcrs, DCRO_PEGPL_OMR3MSKL, 0); + dcr_write(port->dcrs, DCRO_PEGPL_MSGMSK, 0); +} + +static int __init ppc4xx_pciex_wait_on_sdr(struct ppc4xx_pciex_port *port, + unsigned int sdr_offset, + unsigned int mask, + unsigned int value, + int timeout_ms) +{ + u32 val; + + while(timeout_ms--) { + val = mfdcri(SDR0, port->sdr_base + sdr_offset); + if ((val & mask) == value) { + pr_debug("PCIE%d: Wait on SDR %x success with tm %d (%08x)\n", + port->index, sdr_offset, timeout_ms, val); + return 0; + } + msleep(1); + } + return -1; +} + +static int __init ppc4xx_pciex_port_init(struct ppc4xx_pciex_port *port) +{ + int rc = 0; + + /* Init HW */ + if (ppc4xx_pciex_hwops->port_init_hw) + rc = ppc4xx_pciex_hwops->port_init_hw(port); + if (rc != 0) + return rc; + + printk(KERN_INFO "PCIE%d: Checking link...\n", + port->index); + + /* Wait for reset to complete */ + if (ppc4xx_pciex_wait_on_sdr(port, PESDRn_RCSSTS, 1 << 20, 0, 10)) { + printk(KERN_WARNING "PCIE%d: PGRST failed\n", + port->index); + return -1; + } + + /* Check for card presence detect if supported, if not, just wait for + * link unconditionally. + * + * note that we don't fail if there is no link, we just filter out + * config space accesses. That way, it will be easier to implement + * hotplug later on. + */ + if (!port->has_ibpre || + !ppc4xx_pciex_wait_on_sdr(port, PESDRn_LOOP, + 1 << 28, 1 << 28, 100)) { + printk(KERN_INFO + "PCIE%d: Device detected, waiting for link...\n", + port->index); + if (ppc4xx_pciex_wait_on_sdr(port, PESDRn_LOOP, + 0x1000, 0x1000, 2000)) + printk(KERN_WARNING + "PCIE%d: Link up failed\n", port->index); + else { + printk(KERN_INFO + "PCIE%d: link is up !\n", port->index); + port->link = 1; + } + } else + printk(KERN_INFO "PCIE%d: No device detected.\n", port->index); + + /* + * Initialize mapping: disable all regions and configure + * CFG and REG regions based on resources in the device tree + */ + ppc4xx_pciex_port_init_mapping(port); + + /* + * Map UTL + */ + port->utl_base = ioremap(port->utl_regs.start, 0x100); + BUG_ON(port->utl_base == NULL); + + /* + * Setup UTL registers --BenH. + */ + if (ppc4xx_pciex_hwops->setup_utl) + ppc4xx_pciex_hwops->setup_utl(port); + + /* + * Check for VC0 active and assert RDY. + */ + if (port->link && + ppc4xx_pciex_wait_on_sdr(port, PESDRn_RCSSTS, + 1 << 16, 1 << 16, 5000)) { + printk(KERN_INFO "PCIE%d: VC0 not active\n", port->index); + port->link = 0; + } + + mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET, + mfdcri(SDR0, port->sdr_base + PESDRn_RCSSET) | 1 << 20); + msleep(100); + + return 0; +} + +static int ppc4xx_pciex_validate_bdf(struct ppc4xx_pciex_port *port, + struct pci_bus *bus, + unsigned int devfn) +{ + static int message; + + /* Endpoint can not generate upstream(remote) config cycles */ + if (port->endpoint && bus->number != port->hose->first_busno) + return PCIBIOS_DEVICE_NOT_FOUND; + + /* Check we are within the mapped range */ + if (bus->number > port->hose->last_busno) { + if (!message) { + printk(KERN_WARNING "Warning! Probing bus %u" + " out of range !\n", bus->number); + message++; + } + return PCIBIOS_DEVICE_NOT_FOUND; + } + + /* The root complex has only one device / function */ + if (bus->number == port->hose->first_busno && devfn != 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + /* The other side of the RC has only one device as well */ + if (bus->number == (port->hose->first_busno + 1) && + PCI_SLOT(devfn) != 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + /* Check if we have a link */ + if ((bus->number != port->hose->first_busno) && !port->link) + return PCIBIOS_DEVICE_NOT_FOUND; + + return 0; +} + +static void __iomem *ppc4xx_pciex_get_config_base(struct ppc4xx_pciex_port *port, + struct pci_bus *bus, + unsigned int devfn) +{ + int relbus; + + /* Remove the casts when we finally remove the stupid volatile + * in struct pci_controller + */ + if (bus->number == port->hose->first_busno) + return (void __iomem *)port->hose->cfg_addr; + + relbus = bus->number - (port->hose->first_busno + 1); + return (void __iomem *)port->hose->cfg_data + + ((relbus << 20) | (devfn << 12)); +} + +static int ppc4xx_pciex_read_config(struct pci_bus *bus, unsigned int devfn, + int offset, int len, u32 *val) +{ + struct pci_controller *hose = (struct pci_controller *) bus->sysdata; + struct ppc4xx_pciex_port *port = + &ppc4xx_pciex_ports[hose->indirect_type]; + void __iomem *addr; + u32 gpl_cfg; + + BUG_ON(hose != port->hose); + + if (ppc4xx_pciex_validate_bdf(port, bus, devfn) != 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + addr = ppc4xx_pciex_get_config_base(port, bus, devfn); + + /* + * Reading from configuration space of non-existing device can + * generate transaction errors. For the read duration we suppress + * assertion of machine check exceptions to avoid those. + */ + gpl_cfg = dcr_read(port->dcrs, DCRO_PEGPL_CFG); + dcr_write(port->dcrs, DCRO_PEGPL_CFG, gpl_cfg | GPL_DMER_MASK_DISA); + + /* Make sure no CRS is recorded */ + out_be32(port->utl_base + PEUTL_RCSTA, 0x00040000); + + switch (len) { + case 1: + *val = in_8((u8 *)(addr + offset)); + break; + case 2: + *val = in_le16((u16 *)(addr + offset)); + break; + default: + *val = in_le32((u32 *)(addr + offset)); + break; + } + + pr_debug("pcie-config-read: bus=%3d [%3d..%3d] devfn=0x%04x" + " offset=0x%04x len=%d, addr=0x%p val=0x%08x\n", + bus->number, hose->first_busno, hose->last_busno, + devfn, offset, len, addr + offset, *val); + + /* Check for CRS (440SPe rev B does that for us but heh ..) */ + if (in_be32(port->utl_base + PEUTL_RCSTA) & 0x00040000) { + pr_debug("Got CRS !\n"); + if (len != 4 || offset != 0) + return PCIBIOS_DEVICE_NOT_FOUND; + *val = 0xffff0001; + } + + dcr_write(port->dcrs, DCRO_PEGPL_CFG, gpl_cfg); + + return PCIBIOS_SUCCESSFUL; +} + +static int ppc4xx_pciex_write_config(struct pci_bus *bus, unsigned int devfn, + int offset, int len, u32 val) +{ + struct pci_controller *hose = (struct pci_controller *) bus->sysdata; + struct ppc4xx_pciex_port *port = + &ppc4xx_pciex_ports[hose->indirect_type]; + void __iomem *addr; + u32 gpl_cfg; + + if (ppc4xx_pciex_validate_bdf(port, bus, devfn) != 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + addr = ppc4xx_pciex_get_config_base(port, bus, devfn); + + /* + * Reading from configuration space of non-existing device can + * generate transaction errors. For the read duration we suppress + * assertion of machine check exceptions to avoid those. + */ + gpl_cfg = dcr_read(port->dcrs, DCRO_PEGPL_CFG); + dcr_write(port->dcrs, DCRO_PEGPL_CFG, gpl_cfg | GPL_DMER_MASK_DISA); + + pr_debug("pcie-config-write: bus=%3d [%3d..%3d] devfn=0x%04x" + " offset=0x%04x len=%d, addr=0x%p val=0x%08x\n", + bus->number, hose->first_busno, hose->last_busno, + devfn, offset, len, addr + offset, val); + + switch (len) { + case 1: + out_8((u8 *)(addr + offset), val); + break; + case 2: + out_le16((u16 *)(addr + offset), val); + break; + default: + out_le32((u32 *)(addr + offset), val); + break; + } + + dcr_write(port->dcrs, DCRO_PEGPL_CFG, gpl_cfg); + + return PCIBIOS_SUCCESSFUL; +} + +static struct pci_ops ppc4xx_pciex_pci_ops = +{ + .read = ppc4xx_pciex_read_config, + .write = ppc4xx_pciex_write_config, +}; + +static void __init ppc4xx_configure_pciex_POMs(struct ppc4xx_pciex_port *port, + struct pci_controller *hose, + void __iomem *mbase) +{ + u32 lah, lal, pciah, pcial, sa; + int i, j; + + /* Setup outbound memory windows */ + for (i = j = 0; i < 3; i++) { + struct resource *res = &hose->mem_resources[i]; + + /* we only care about memory windows */ + if (!(res->flags & IORESOURCE_MEM)) + continue; + if (j > 1) { + printk(KERN_WARNING "%s: Too many ranges\n", + port->node->full_name); + break; + } + + /* Calculate register values */ + lah = RES_TO_U32_HIGH(res->start); + lal = RES_TO_U32_LOW(res->start); + pciah = RES_TO_U32_HIGH(res->start - hose->pci_mem_offset); + pcial = RES_TO_U32_LOW(res->start - hose->pci_mem_offset); + sa = res->end + 1 - res->start; + if (!is_power_of_2(sa) || sa < 0x100000 || + sa > 0xffffffffu) { + printk(KERN_WARNING "%s: Resource out of range\n", + port->node->full_name); + continue; + } + sa = (0xffffffffu << ilog2(sa)) | 0x1; + + /* Program register values */ + switch (j) { + case 0: + out_le32(mbase + PECFG_POM0LAH, pciah); + out_le32(mbase + PECFG_POM0LAL, pcial); + dcr_write(port->dcrs, DCRO_PEGPL_OMR1BAH, lah); + dcr_write(port->dcrs, DCRO_PEGPL_OMR1BAL, lal); + dcr_write(port->dcrs, DCRO_PEGPL_OMR1MSKH, 0x7fffffff); + dcr_write(port->dcrs, DCRO_PEGPL_OMR1MSKL, sa | 3); + break; + case 1: + out_le32(mbase + PECFG_POM1LAH, pciah); + out_le32(mbase + PECFG_POM1LAL, pcial); + dcr_write(port->dcrs, DCRO_PEGPL_OMR2BAH, lah); + dcr_write(port->dcrs, DCRO_PEGPL_OMR2BAL, lal); + dcr_write(port->dcrs, DCRO_PEGPL_OMR2MSKH, 0x7fffffff); + dcr_write(port->dcrs, DCRO_PEGPL_OMR2MSKL, sa | 3); + break; + } + j++; + } + + /* Configure IO, always 64K starting at 0 */ + if (hose->io_resource.flags & IORESOURCE_IO) { + lah = RES_TO_U32_HIGH(hose->io_base_phys); + lal = RES_TO_U32_LOW(hose->io_base_phys); + out_le32(mbase + PECFG_POM2LAH, 0); + out_le32(mbase + PECFG_POM2LAL, 0); + dcr_write(port->dcrs, DCRO_PEGPL_OMR3BAH, lah); + dcr_write(port->dcrs, DCRO_PEGPL_OMR3BAL, lal); + dcr_write(port->dcrs, DCRO_PEGPL_OMR3MSKH, 0x7fffffff); + dcr_write(port->dcrs, DCRO_PEGPL_OMR3MSKL, 0xffff0000 | 3); + } +} + +static void __init ppc4xx_configure_pciex_PIMs(struct ppc4xx_pciex_port *port, + struct pci_controller *hose, + void __iomem *mbase, + struct resource *res) +{ + resource_size_t size = res->end - res->start + 1; + u64 sa; + + /* Calculate window size */ + sa = (0xffffffffffffffffull << ilog2(size));; + if (res->flags & IORESOURCE_PREFETCH) + sa |= 0x8; + + out_le32(mbase + PECFG_BAR0HMPA, RES_TO_U32_HIGH(sa)); + out_le32(mbase + PECFG_BAR0LMPA, RES_TO_U32_LOW(sa)); + + /* The setup of the split looks weird to me ... let's see if it works */ + out_le32(mbase + PECFG_PIM0LAL, 0x00000000); + out_le32(mbase + PECFG_PIM0LAH, 0x00000000); + out_le32(mbase + PECFG_PIM1LAL, 0x00000000); + out_le32(mbase + PECFG_PIM1LAH, 0x00000000); + out_le32(mbase + PECFG_PIM01SAH, 0xffff0000); + out_le32(mbase + PECFG_PIM01SAL, 0x00000000); + + /* Enable inbound mapping */ + out_le32(mbase + PECFG_PIMEN, 0x1); + + out_le32(mbase + PCI_BASE_ADDRESS_0, RES_TO_U32_LOW(res->start)); + out_le32(mbase + PCI_BASE_ADDRESS_1, RES_TO_U32_HIGH(res->start)); + + /* Enable I/O, Mem, and Busmaster cycles */ + out_le16(mbase + PCI_COMMAND, + in_le16(mbase + PCI_COMMAND) | + PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); +} + +static void __init ppc4xx_pciex_port_setup_hose(struct ppc4xx_pciex_port *port) +{ + struct resource dma_window; + struct pci_controller *hose = NULL; + const int *bus_range; + int primary = 0, busses; + void __iomem *mbase = NULL, *cfg_data = NULL; + + /* XXX FIXME: Handle endpoint mode properly */ + if (port->endpoint) { + printk(KERN_WARNING "PCIE%d: Port in endpoint mode !\n", + port->index); + return; + } + + /* Check if primary bridge */ + if (of_get_property(port->node, "primary", NULL)) + primary = 1; + + /* Get bus range if any */ + bus_range = of_get_property(port->node, "bus-range", NULL); + + /* Allocate the host controller data structure */ + hose = pcibios_alloc_controller(port->node); + if (!hose) + goto fail; + + /* We stick the port number in "indirect_type" so the config space + * ops can retrieve the port data structure easily + */ + hose->indirect_type = port->index; + + /* Get bus range */ + hose->first_busno = bus_range ? bus_range[0] : 0x0; + hose->last_busno = bus_range ? bus_range[1] : 0xff; + + /* Because of how big mapping the config space is (1M per bus), we + * limit how many busses we support. In the long run, we could replace + * that with something akin to kmap_atomic instead. We set aside 1 bus + * for the host itself too. + */ + busses = hose->last_busno - hose->first_busno; /* This is off by 1 */ + if (busses > MAX_PCIE_BUS_MAPPED) { + busses = MAX_PCIE_BUS_MAPPED; + hose->last_busno = hose->first_busno + busses; + } + + /* We map the external config space in cfg_data and the host config + * space in cfg_addr. External space is 1M per bus, internal space + * is 4K + */ + cfg_data = ioremap(port->cfg_space.start + + (hose->first_busno + 1) * 0x100000, + busses * 0x100000); + mbase = ioremap(port->cfg_space.start + 0x10000000, 0x1000); + if (cfg_data == NULL || mbase == NULL) { + printk(KERN_ERR "%s: Can't map config space !", + port->node->full_name); + goto fail; + } + + hose->cfg_data = cfg_data; + hose->cfg_addr = mbase; + + pr_debug("PCIE %s, bus %d..%d\n", port->node->full_name, + hose->first_busno, hose->last_busno); + pr_debug(" config space mapped at: root @0x%p, other @0x%p\n", + hose->cfg_addr, hose->cfg_data); + + /* Setup config space */ + hose->ops = &ppc4xx_pciex_pci_ops; + port->hose = hose; + mbase = (void __iomem *)hose->cfg_addr; + + /* + * Set bus numbers on our root port + */ + out_8(mbase + PCI_PRIMARY_BUS, hose->first_busno); + out_8(mbase + PCI_SECONDARY_BUS, hose->first_busno + 1); + out_8(mbase + PCI_SUBORDINATE_BUS, hose->last_busno); + + /* + * OMRs are already reset, also disable PIMs + */ + out_le32(mbase + PECFG_PIMEN, 0); + + /* Parse outbound mapping resources */ + pci_process_bridge_OF_ranges(hose, port->node, primary); + + /* Parse inbound mapping resources */ + if (ppc4xx_parse_dma_ranges(hose, mbase, &dma_window) != 0) + goto fail; + + /* Configure outbound ranges POMs */ + ppc4xx_configure_pciex_POMs(port, hose, mbase); + + /* Configure inbound ranges PIMs */ + ppc4xx_configure_pciex_PIMs(port, hose, mbase, &dma_window); + + /* The root complex doesn't show up if we don't set some vendor + * and device IDs into it. Those are the same bogus one that the + * initial code in arch/ppc add. We might want to change that. + */ + out_le16(mbase + 0x200, 0xaaa0 + port->index); + out_le16(mbase + 0x202, 0xbed0 + port->index); + + /* Set Class Code to PCI-PCI bridge and Revision Id to 1 */ + out_le32(mbase + 0x208, 0x06040001); + + printk(KERN_INFO "PCIE%d: successfully set as root-complex\n", + port->index); + return; + fail: + if (hose) + pcibios_free_controller(hose); + if (cfg_data) + iounmap(cfg_data); + if (mbase) + iounmap(mbase); +} + +static void __init ppc4xx_probe_pciex_bridge(struct device_node *np) +{ + struct ppc4xx_pciex_port *port; + const u32 *pval; + int portno; + unsigned int dcrs; + + /* First, proceed to core initialization as we assume there's + * only one PCIe core in the system + */ + if (ppc4xx_pciex_check_core_init(np)) + return; + + /* Get the port number from the device-tree */ + pval = of_get_property(np, "port", NULL); + if (pval == NULL) { + printk(KERN_ERR "PCIE: Can't find port number for %s\n", + np->full_name); + return; + } + portno = *pval; + if (portno >= ppc4xx_pciex_port_count) { + printk(KERN_ERR "PCIE: port number out of range for %s\n", + np->full_name); + return; + } + port = &ppc4xx_pciex_ports[portno]; + port->index = portno; + port->node = of_node_get(np); + pval = of_get_property(np, "sdr-base", NULL); + if (pval == NULL) { + printk(KERN_ERR "PCIE: missing sdr-base for %s\n", + np->full_name); + return; + } + port->sdr_base = *pval; + + /* XXX Currently, we only support root complex mode */ + port->endpoint = 0; + + /* Fetch config space registers address */ + if (of_address_to_resource(np, 0, &port->cfg_space)) { + printk(KERN_ERR "%s: Can't get PCI-E config space !", + np->full_name); + return; + } + /* Fetch host bridge internal registers address */ + if (of_address_to_resource(np, 1, &port->utl_regs)) { + printk(KERN_ERR "%s: Can't get UTL register base !", + np->full_name); + return; + } + + /* Map DCRs */ + dcrs = dcr_resource_start(np, 0); + if (dcrs == 0) { + printk(KERN_ERR "%s: Can't get DCR register base !", + np->full_name); + return; + } + port->dcrs = dcr_map(np, dcrs, dcr_resource_len(np, 0)); + + /* Initialize the port specific registers */ + if (ppc4xx_pciex_port_init(port)) { + printk(KERN_WARNING "PCIE%d: Port init failed\n", port->index); + return; + } + + /* Setup the linux hose data structure */ + ppc4xx_pciex_port_setup_hose(port); +} + +#endif /* CONFIG_PPC4xx_PCI_EXPRESS */ + +static int __init ppc4xx_pci_find_bridges(void) +{ + struct device_node *np; + +#ifdef CONFIG_PPC4xx_PCI_EXPRESS + for_each_compatible_node(np, NULL, "ibm,plb-pciex") + ppc4xx_probe_pciex_bridge(np); +#endif + for_each_compatible_node(np, NULL, "ibm,plb-pcix") + ppc4xx_probe_pcix_bridge(np); + for_each_compatible_node(np, NULL, "ibm,plb-pci") + ppc4xx_probe_pci_bridge(np); + + return 0; +} +arch_initcall(ppc4xx_pci_find_bridges); + |