diff options
Diffstat (limited to 'arch/ppc/8xx_io/enet.c')
| -rw-r--r-- | arch/ppc/8xx_io/enet.c | 52 |
1 files changed, 44 insertions, 8 deletions
diff --git a/arch/ppc/8xx_io/enet.c b/arch/ppc/8xx_io/enet.c index 4ea7158e506..ece6a9fbe09 100644 --- a/arch/ppc/8xx_io/enet.c +++ b/arch/ppc/8xx_io/enet.c @@ -714,16 +714,24 @@ static int __init scc_enet_init(void) immap->im_ioport.iop_pcdat &= ~PC_ENET_LBK; /* Disable Loopback */ #endif /* PC_ENET_LBK */ - /* Configure port C pins to enable CLSN and RENA. +#ifdef PE_ENET_TCLK + /* Configure port E for TCLK and RCLK. */ - immap->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA); - immap->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA); - immap->im_ioport.iop_pcso |= (PC_ENET_CLSN | PC_ENET_RENA); - + cp->cp_pepar |= (PE_ENET_TCLK | PE_ENET_RCLK); + cp->cp_pedir &= ~(PE_ENET_TCLK | PE_ENET_RCLK); + cp->cp_peso &= ~(PE_ENET_TCLK | PE_ENET_RCLK); +#else /* Configure port A for TCLK and RCLK. */ immap->im_ioport.iop_papar |= (PA_ENET_TCLK | PA_ENET_RCLK); immap->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK); +#endif + + /* Configure port C pins to enable CLSN and RENA. + */ + immap->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA); + immap->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA); + immap->im_ioport.iop_pcso |= (PC_ENET_CLSN | PC_ENET_RENA); /* Configure Serial Interface clock routing. * First, clear all SCC bits to zero, then set the ones we want. @@ -896,14 +904,18 @@ static int __init scc_enet_init(void) /* It is now OK to enable the Ethernet transmitter. * Unfortunately, there are board implementation differences here. */ -#if (!defined (PB_ENET_TENA) && defined (PC_ENET_TENA)) +#if (!defined (PB_ENET_TENA) && defined (PC_ENET_TENA) && !defined (PE_ENET_TENA)) immap->im_ioport.iop_pcpar |= PC_ENET_TENA; immap->im_ioport.iop_pcdir &= ~PC_ENET_TENA; -#elif ( defined (PB_ENET_TENA) && !defined (PC_ENET_TENA)) +#elif ( defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && !defined (PE_ENET_TENA)) cp->cp_pbpar |= PB_ENET_TENA; cp->cp_pbdir |= PB_ENET_TENA; +#elif ( !defined (PB_ENET_TENA) && !defined (PC_ENET_TENA) && defined (PE_ENET_TENA)) + cp->cp_pepar |= PE_ENET_TENA; + cp->cp_pedir &= ~PE_ENET_TENA; + cp->cp_peso |= PE_ENET_TENA; #else -#error Configuration Error: define exactly ONE of PB_ENET_TENA, PC_ENET_TENA +#error Configuration Error: define exactly ONE of PB_ENET_TENA, PC_ENET_TENA, PE_ENET_TENA #endif #if defined(CONFIG_RPXLITE) || defined(CONFIG_RPXCLASSIC) @@ -936,6 +948,29 @@ static int __init scc_enet_init(void) *((volatile uint *)BCSR1) &= ~BCSR1_ETHEN; #endif +#ifdef CONFIG_MPC885ADS + + /* Deassert PHY reset and enable the PHY. + */ + { + volatile uint __iomem *bcsr = ioremap(BCSR_ADDR, BCSR_SIZE); + uint tmp; + + tmp = in_be32(bcsr + 1 /* BCSR1 */); + tmp |= BCSR1_ETHEN; + out_be32(bcsr + 1, tmp); + tmp = in_be32(bcsr + 4 /* BCSR4 */); + tmp |= BCSR4_ETH10_RST; + out_be32(bcsr + 4, tmp); + iounmap(bcsr); + } + + /* On MPC885ADS SCC ethernet PHY defaults to the full duplex mode + * upon reset. SCC is set to half duplex by default. So this + * inconsistency should be better fixed by the software. + */ +#endif + dev->base_addr = (unsigned long)ep; #if 0 dev->name = "CPM_ENET"; @@ -969,3 +1004,4 @@ static int __init scc_enet_init(void) } module_init(scc_enet_init); + |