diff options
Diffstat (limited to 'arch/ppc/Kconfig')
| -rw-r--r-- | arch/ppc/Kconfig | 154 |
1 files changed, 6 insertions, 148 deletions
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig index 6bdeeb70b15..20dce468125 100644 --- a/arch/ppc/Kconfig +++ b/arch/ppc/Kconfig @@ -4,6 +4,10 @@ mainmenu "Linux/PowerPC Kernel Configuration" +config WORD_SIZE + int + default 32 + config MMU bool default y @@ -573,24 +577,9 @@ choice Select PReP if configuring for a PReP machine. - Select Gemini if configuring for a Synergy Microsystems' Gemini - series Single Board Computer. More information is available at: - <http://www.synergymicro.com/PressRel/97_10_15.html>. - - Select APUS if configuring for a PowerUP Amiga. More information is - available at: <http://linux-apus.sourceforge.net/>. - config PPC_PREP bool "PReP" -config APUS - bool "Amiga-APUS" - depends on BROKEN - help - Select APUS if configuring for a PowerUP Amiga. - More information is available at: - <http://linux-apus.sourceforge.net/>. - config KATANA bool "Artesyn-Katana" help @@ -1027,133 +1016,7 @@ config CMDLINE some command-line options at build time by entering them here. In most cases you will need to specify the root device here. -config AMIGA - bool - depends on APUS - default y - help - This option enables support for the Amiga series of computers. - -config ZORRO - bool - depends on APUS - default y - help - This enables support for the Zorro bus in the Amiga. If you have - expansion cards in your Amiga that conform to the Amiga - AutoConfig(tm) specification, say Y, otherwise N. Note that even - expansion cards that do not fit in the Zorro slots but fit in e.g. - the CPU slot may fall in this category, so you have to say Y to let - Linux use these. - -config ABSTRACT_CONSOLE - bool - depends on APUS - default y - -config APUS_FAST_EXCEPT - bool - depends on APUS - default y - -config AMIGA_PCMCIA - bool "Amiga 1200/600 PCMCIA support" - depends on APUS && EXPERIMENTAL - help - Include support in the kernel for pcmcia on Amiga 1200 and Amiga - 600. If you intend to use pcmcia cards say Y; otherwise say N. - -config AMIGA_BUILTIN_SERIAL - tristate "Amiga builtin serial support" - depends on APUS - help - If you want to use your Amiga's built-in serial port in Linux, - answer Y. - - To compile this driver as a module, choose M here. - -config GVPIOEXT - tristate "GVP IO-Extender support" - depends on APUS - help - If you want to use a GVP IO-Extender serial card in Linux, say Y. - Otherwise, say N. - -config GVPIOEXT_LP - tristate "GVP IO-Extender parallel printer support" - depends on GVPIOEXT - help - Say Y to enable driving a printer from the parallel port on your - GVP IO-Extender card, N otherwise. - -config GVPIOEXT_PLIP - tristate "GVP IO-Extender PLIP support" - depends on GVPIOEXT - help - Say Y to enable doing IP over the parallel port on your GVP - IO-Extender card, N otherwise. - -config MULTIFACE_III_TTY - tristate "Multiface Card III serial support" - depends on APUS - help - If you want to use a Multiface III card's serial port in Linux, - answer Y. - - To compile this driver as a module, choose M here. - -config A2232 - tristate "Commodore A2232 serial support (EXPERIMENTAL)" - depends on EXPERIMENTAL && APUS - ---help--- - This option supports the 2232 7-port serial card shipped with the - Amiga 2000 and other Zorro-bus machines, dating from 1989. At - a max of 19,200 bps, the ports are served by a 6551 ACIA UART chip - each, plus a 8520 CIA, and a master 6502 CPU and buffer as well. The - ports were connected with 8 pin DIN connectors on the card bracket, - for which 8 pin to DB25 adapters were supplied. The card also had - jumpers internally to toggle various pinning configurations. - - This driver can be built as a module; but then "generic_serial" - will also be built as a module. This has to be loaded before - "ser_a2232". If you want to do this, answer M here. - -config WHIPPET_SERIAL - tristate "Hisoft Whippet PCMCIA serial support" - depends on AMIGA_PCMCIA - help - HiSoft has a web page at <http://www.hisoft.co.uk/>, but there - is no listing for the Whippet in their Amiga section. - -config APNE - tristate "PCMCIA NE2000 support" - depends on AMIGA_PCMCIA - help - If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, - say N. - - To compile this driver as a module, choose M here: the - module will be called apne. - -config SERIAL_CONSOLE - bool "Support for serial port console" - depends on APUS && (AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y) - -config HEARTBEAT - bool "Use power LED as a heartbeat" - depends on APUS - help - Use the power-on LED on your machine as a load meter. The exact - behavior is platform-dependent, but normally the flash frequency is - a hyperbolic function of the 5-minute load average. - -config PROC_HARDWARE - bool "/proc/hardware support" - depends on APUS - -source "drivers/zorro/Kconfig" - -if !44x || BROKEN +if BROKEN source kernel/power/Kconfig endif @@ -1227,8 +1090,7 @@ config MCA config PCI bool "PCI support" if 40x || CPM2 || 83xx || 85xx || PPC_MPC52xx - default y if !40x && !CPM2 && !8xx && !APUS && !83xx && !85xx - default PCI_PERMEDIA if !4xx && !CPM2 && !8xx && APUS + default y if !40x && !CPM2 && !8xx && !83xx && !85xx default PCI_QSPAN if !4xx && !CPM2 && 8xx help Find out whether your system includes a PCI bus. PCI is the name of @@ -1284,10 +1146,6 @@ config 8260_PCI9_IDMA4 endchoice -config PCI_PERMEDIA - bool "PCI for Permedia2" - depends on !4xx && !8xx && APUS - source "drivers/pci/Kconfig" source "drivers/pcmcia/Kconfig" |