diff options
Diffstat (limited to 'arch/ppc/boot/simple/m8260_tty.c')
| -rw-r--r-- | arch/ppc/boot/simple/m8260_tty.c | 325 |
1 files changed, 325 insertions, 0 deletions
diff --git a/arch/ppc/boot/simple/m8260_tty.c b/arch/ppc/boot/simple/m8260_tty.c new file mode 100644 index 00000000000..d770947e9b8 --- /dev/null +++ b/arch/ppc/boot/simple/m8260_tty.c @@ -0,0 +1,325 @@ +/* Minimal serial functions needed to send messages out the serial + * port on SMC1. + */ +#include <linux/types.h> +#include <asm/mpc8260.h> +#include <asm/cpm2.h> +#include <asm/immap_cpm2.h> + +uint no_print; +extern char *params[]; +extern int nparams; +static u_char cons_hold[128], *sgptr; +static int cons_hold_cnt; + +/* If defined, enables serial console. The value (1 through 4) + * should designate which SCC is used, but this isn't complete. Only + * SCC1 is known to work at this time. + * We're only linked if SERIAL_CPM_CONSOLE=y, so we only need to test + * SERIAL_CPM_SCC1. + */ +#ifdef CONFIG_SERIAL_CPM_SCC1 +#define SCC_CONSOLE 1 +#endif + +unsigned long +serial_init(int ignored, bd_t *bd) +{ +#ifdef SCC_CONSOLE + volatile scc_t *sccp; + volatile scc_uart_t *sup; +#else + volatile smc_t *sp; + volatile smc_uart_t *up; +#endif + volatile cbd_t *tbdf, *rbdf; + volatile cpm2_map_t *ip; + volatile iop_cpm2_t *io; + volatile cpm_cpm2_t *cp; + uint dpaddr, memaddr; + + ip = (cpm2_map_t *)CPM_MAP_ADDR; + cp = &ip->im_cpm; + io = &ip->im_ioport; + + /* Perform a reset. + */ + cp->cp_cpcr = (CPM_CR_RST | CPM_CR_FLG); + + /* Wait for it. + */ + while (cp->cp_cpcr & CPM_CR_FLG); + +#ifdef CONFIG_ADS8260 + /* Enable the RS-232 transceivers. + */ + *(volatile uint *)(BCSR_ADDR + 4) &= + ~(BCSR1_RS232_EN1 | BCSR1_RS232_EN2); +#endif + +#ifdef SCC_CONSOLE + sccp = (scc_t *)&(ip->im_scc[SCC_CONSOLE-1]); + sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; + sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX); + sccp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT); + + /* Use Port D for SCC1 instead of other functions. + */ + io->iop_ppard |= 0x00000003; + io->iop_psord &= ~0x00000001; /* Rx */ + io->iop_psord |= 0x00000002; /* Tx */ + io->iop_pdird &= ~0x00000001; /* Rx */ + io->iop_pdird |= 0x00000002; /* Tx */ + +#else + sp = (smc_t*)&(ip->im_smc[0]); + *(ushort *)(&ip->im_dprambase[PROFF_SMC1_BASE]) = PROFF_SMC1; + up = (smc_uart_t *)&ip->im_dprambase[PROFF_SMC1]; + + /* Disable transmitter/receiver. + */ + sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN); + + /* Use Port D for SMC1 instead of other functions. + */ + io->iop_ppard |= 0x00c00000; + io->iop_pdird |= 0x00400000; + io->iop_pdird &= ~0x00800000; + io->iop_psord &= ~0x00c00000; +#endif + + /* Allocate space for two buffer descriptors in the DP ram. + * For now, this address seems OK, but it may have to + * change with newer versions of the firmware. + */ + dpaddr = 0x0800; + + /* Grab a few bytes from the top of memory. + */ + memaddr = (bd->bi_memsize - 256) & ~15; + + /* Set the physical address of the host memory buffers in + * the buffer descriptors. + */ + rbdf = (cbd_t *)&ip->im_dprambase[dpaddr]; + rbdf->cbd_bufaddr = memaddr; + rbdf->cbd_sc = 0; + tbdf = rbdf + 1; + tbdf->cbd_bufaddr = memaddr+128; + tbdf->cbd_sc = 0; + + /* Set up the uart parameters in the parameter ram. + */ +#ifdef SCC_CONSOLE + sup->scc_genscc.scc_rbase = dpaddr; + sup->scc_genscc.scc_tbase = dpaddr + sizeof(cbd_t); + + /* Set up the uart parameters in the + * parameter ram. + */ + sup->scc_genscc.scc_rfcr = CPMFCR_GBL | CPMFCR_EB; + sup->scc_genscc.scc_tfcr = CPMFCR_GBL | CPMFCR_EB; + + sup->scc_genscc.scc_mrblr = 128; + sup->scc_maxidl = 8; + sup->scc_brkcr = 1; + sup->scc_parec = 0; + sup->scc_frmec = 0; + sup->scc_nosec = 0; + sup->scc_brkec = 0; + sup->scc_uaddr1 = 0; + sup->scc_uaddr2 = 0; + sup->scc_toseq = 0; + sup->scc_char1 = 0x8000; + sup->scc_char2 = 0x8000; + sup->scc_char3 = 0x8000; + sup->scc_char4 = 0x8000; + sup->scc_char5 = 0x8000; + sup->scc_char6 = 0x8000; + sup->scc_char7 = 0x8000; + sup->scc_char8 = 0x8000; + sup->scc_rccm = 0xc0ff; + + /* Send the CPM an initialize command. + */ + cp->cp_cpcr = mk_cr_cmd(CPM_CR_SCC1_PAGE, CPM_CR_SCC1_SBLOCK, 0, + CPM_CR_INIT_TRX) | CPM_CR_FLG; + while (cp->cp_cpcr & CPM_CR_FLG); + + /* Set UART mode, 8 bit, no parity, one stop. + * Enable receive and transmit. + */ + sccp->scc_gsmrh = 0; + sccp->scc_gsmrl = + (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16); + + /* Disable all interrupts and clear all pending + * events. + */ + sccp->scc_sccm = 0; + sccp->scc_scce = 0xffff; + sccp->scc_dsr = 0x7e7e; + sccp->scc_psmr = 0x3000; + + /* Wire BRG1 to SCC1. The console driver will take care of + * others. + */ + ip->im_cpmux.cmx_scr = 0; +#else + up->smc_rbase = dpaddr; + up->smc_tbase = dpaddr+sizeof(cbd_t); + up->smc_rfcr = CPMFCR_EB; + up->smc_tfcr = CPMFCR_EB; + up->smc_brklen = 0; + up->smc_brkec = 0; + up->smc_brkcr = 0; + up->smc_mrblr = 128; + up->smc_maxidl = 8; + + /* Set UART mode, 8 bit, no parity, one stop. + * Enable receive and transmit. + */ + sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART; + + /* Mask all interrupts and remove anything pending. + */ + sp->smc_smcm = 0; + sp->smc_smce = 0xff; + + /* Set up the baud rate generator. + */ + ip->im_cpmux.cmx_smr = 0; +#endif + + /* The baud rate divisor needs to be coordinated with clk_8260(). + */ + ip->im_brgc1 = + (((bd->bi_brgfreq/16) / bd->bi_baudrate) << 1) | + CPM_BRG_EN; + + /* Make the first buffer the only buffer. + */ + tbdf->cbd_sc |= BD_SC_WRAP; + rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP; + + /* Initialize Tx/Rx parameters. + */ +#ifdef SCC_CONSOLE + sccp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT); +#else + cp->cp_cpcr = mk_cr_cmd(CPM_CR_SMC1_PAGE, CPM_CR_SMC1_SBLOCK, 0, CPM_CR_INIT_TRX) | CPM_CR_FLG; + while (cp->cp_cpcr & CPM_CR_FLG); + + /* Enable transmitter/receiver. + */ + sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN; +#endif + + /* This is ignored. + */ + return 0; +} + +int +serial_readbuf(u_char *cbuf) +{ + volatile cbd_t *rbdf; + volatile char *buf; +#ifdef SCC_CONSOLE + volatile scc_uart_t *sup; +#else + volatile smc_uart_t *up; +#endif + volatile cpm2_map_t *ip; + int i, nc; + + ip = (cpm2_map_t *)CPM_MAP_ADDR; + +#ifdef SCC_CONSOLE + sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; + rbdf = (cbd_t *)&ip->im_dprambase[sup->scc_genscc.scc_rbase]; +#else + up = (smc_uart_t *)&(ip->im_dprambase[PROFF_SMC1]); + rbdf = (cbd_t *)&ip->im_dprambase[up->smc_rbase]; +#endif + + /* Wait for character to show up. + */ + buf = (char *)rbdf->cbd_bufaddr; + while (rbdf->cbd_sc & BD_SC_EMPTY); + nc = rbdf->cbd_datlen; + for (i=0; i<nc; i++) + *cbuf++ = *buf++; + rbdf->cbd_sc |= BD_SC_EMPTY; + + return(nc); +} + +void +serial_putc(void *ignored, const char c) +{ + volatile cbd_t *tbdf; + volatile char *buf; +#ifdef SCC_CONSOLE + volatile scc_uart_t *sup; +#else + volatile smc_uart_t *up; +#endif + volatile cpm2_map_t *ip; + + ip = (cpm2_map_t *)CPM_MAP_ADDR; +#ifdef SCC_CONSOLE + sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; + tbdf = (cbd_t *)&ip->im_dprambase[sup->scc_genscc.scc_tbase]; +#else + up = (smc_uart_t *)&(ip->im_dprambase[PROFF_SMC1]); + tbdf = (cbd_t *)&ip->im_dprambase[up->smc_tbase]; +#endif + + /* Wait for last character to go. + */ + buf = (char *)tbdf->cbd_bufaddr; + while (tbdf->cbd_sc & BD_SC_READY); + + *buf = c; + tbdf->cbd_datlen = 1; + tbdf->cbd_sc |= BD_SC_READY; +} + +char +serial_getc(void *ignored) +{ + char c; + + if (cons_hold_cnt <= 0) { + cons_hold_cnt = serial_readbuf(cons_hold); + sgptr = cons_hold; + } + c = *sgptr++; + cons_hold_cnt--; + + return(c); +} + +int +serial_tstc(void *ignored) +{ + volatile cbd_t *rbdf; +#ifdef SCC_CONSOLE + volatile scc_uart_t *sup; +#else + volatile smc_uart_t *up; +#endif + volatile cpm2_map_t *ip; + + ip = (cpm2_map_t *)CPM_MAP_ADDR; +#ifdef SCC_CONSOLE + sup = (scc_uart_t *)&ip->im_dprambase[PROFF_SCC1 + ((SCC_CONSOLE-1) << 8)]; + rbdf = (cbd_t *)&ip->im_dprambase[sup->scc_genscc.scc_rbase]; +#else + up = (smc_uart_t *)&(ip->im_dprambase[PROFF_SMC1]); + rbdf = (cbd_t *)&ip->im_dprambase[up->smc_rbase]; +#endif + + return(!(rbdf->cbd_sc & BD_SC_EMPTY)); +} |