diff options
Diffstat (limited to 'arch/ppc/kernel/head.S')
| -rw-r--r-- | arch/ppc/kernel/head.S | 117 |
1 files changed, 4 insertions, 113 deletions
diff --git a/arch/ppc/kernel/head.S b/arch/ppc/kernel/head.S index c7cb9d5f24a..1b0ec7202dd 100644 --- a/arch/ppc/kernel/head.S +++ b/arch/ppc/kernel/head.S @@ -32,10 +32,6 @@ #include <asm/ppc_asm.h> #include <asm/asm-offsets.h> -#ifdef CONFIG_APUS -#include <asm/amigappc.h> -#endif - /* 601 only have IBAT; cr0.eq is set on 601 when using this macro */ #define LOAD_BAT(n, reg, RA, RB) \ /* see the comment for clear_bats() -- Cort */ \ @@ -128,14 +124,6 @@ __start: */ bl early_init -#ifdef CONFIG_APUS -/* On APUS the __va/__pa constants need to be set to the correct - * values before continuing. - */ - mr r4,r30 - bl fix_mem_constants -#endif /* CONFIG_APUS */ - /* Switch MMU off, clear BATs and flush TLB. At this point, r3 contains * the physical address we are running at, returned by early_init() */ @@ -145,7 +133,7 @@ __after_mmu_off: bl flush_tlbs bl initial_bats -#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) +#ifdef CONFIG_BOOTX_TEXT bl setup_disp_bat #endif @@ -161,7 +149,6 @@ __after_mmu_off: #endif /* CONFIG_6xx */ -#ifndef CONFIG_APUS /* * We need to run with _start at physical address 0. * If the MMU is already turned on, we copy stuff to KERNELBASE, @@ -172,7 +159,7 @@ __after_mmu_off: addis r4,r3,KERNELBASE@h /* current address of _start */ cmpwi 0,r4,0 /* are we already running at 0? */ bne relocate_kernel -#endif /* CONFIG_APUS */ + /* * we now have the 1st 16M of ram mapped with the bats. * prep needs the mmu to be turned on here, but pmac already has it on. @@ -812,85 +799,6 @@ copy_and_flush: addi r6,r6,4 blr -#ifdef CONFIG_APUS -/* - * On APUS the physical base address of the kernel is not known at compile - * time, which means the __pa/__va constants used are incorrect. In the - * __init section is recorded the virtual addresses of instructions using - * these constants, so all that has to be done is fix these before - * continuing the kernel boot. - * - * r4 = The physical address of the kernel base. - */ -fix_mem_constants: - mr r10,r4 - addis r10,r10,-KERNELBASE@h /* virt_to_phys constant */ - neg r11,r10 /* phys_to_virt constant */ - - lis r12,__vtop_table_begin@h - ori r12,r12,__vtop_table_begin@l - add r12,r12,r10 /* table begin phys address */ - lis r13,__vtop_table_end@h - ori r13,r13,__vtop_table_end@l - add r13,r13,r10 /* table end phys address */ - subi r12,r12,4 - subi r13,r13,4 -1: lwzu r14,4(r12) /* virt address of instruction */ - add r14,r14,r10 /* phys address of instruction */ - lwz r15,0(r14) /* instruction, now insert top */ - rlwimi r15,r10,16,16,31 /* half of vp const in low half */ - stw r15,0(r14) /* of instruction and restore. */ - dcbst r0,r14 /* write it to memory */ - sync - icbi r0,r14 /* flush the icache line */ - cmpw r12,r13 - bne 1b - sync /* additional sync needed on g4 */ - isync - -/* - * Map the memory where the exception handlers will - * be copied to when hash constants have been patched. - */ -#ifdef CONFIG_APUS_FAST_EXCEPT - lis r8,0xfff0 -#else - lis r8,0 -#endif - ori r8,r8,0x2 /* 128KB, supervisor */ - mtspr SPRN_DBAT3U,r8 - mtspr SPRN_DBAT3L,r8 - - lis r12,__ptov_table_begin@h - ori r12,r12,__ptov_table_begin@l - add r12,r12,r10 /* table begin phys address */ - lis r13,__ptov_table_end@h - ori r13,r13,__ptov_table_end@l - add r13,r13,r10 /* table end phys address */ - subi r12,r12,4 - subi r13,r13,4 -1: lwzu r14,4(r12) /* virt address of instruction */ - add r14,r14,r10 /* phys address of instruction */ - lwz r15,0(r14) /* instruction, now insert top */ - rlwimi r15,r11,16,16,31 /* half of pv const in low half*/ - stw r15,0(r14) /* of instruction and restore. */ - dcbst r0,r14 /* write it to memory */ - sync - icbi r0,r14 /* flush the icache line */ - cmpw r12,r13 - bne 1b - - sync /* additional sync needed on g4 */ - isync /* No speculative loading until now */ - blr - -/*********************************************************************** - * Please note that on APUS the exception handlers are located at the - * physical address 0xfff0000. For this reason, the exception handlers - * cannot use relative branches to access the code below. - ***********************************************************************/ -#endif /* CONFIG_APUS */ - #ifdef CONFIG_SMP .globl __secondary_start_pmac_0 __secondary_start_pmac_0: @@ -1043,19 +951,6 @@ start_here: bl machine_init bl MMU_init -#ifdef CONFIG_APUS - /* Copy exception code to exception vector base on APUS. */ - lis r4,KERNELBASE@h -#ifdef CONFIG_APUS_FAST_EXCEPT - lis r3,0xfff0 /* Copy to 0xfff00000 */ -#else - lis r3,0 /* Copy to 0x00000000 */ -#endif - li r5,0x4000 /* # bytes of memory to copy */ - li r6,0 - bl copy_and_flush /* copy the first 0x4000 bytes */ -#endif /* CONFIG_APUS */ - /* * Go back to running unmapped so we can load up new values * for SDR1 (hash table pointer) and the segment registers @@ -1232,11 +1127,7 @@ initial_bats: #else ori r8,r8,2 /* R/W access */ #endif /* CONFIG_SMP */ -#ifdef CONFIG_APUS - ori r11,r11,BL_8M<<2|0x2 /* set up 8MB BAT registers for 604 */ -#else ori r11,r11,BL_256M<<2|0x2 /* set up BAT registers for 604 */ -#endif /* CONFIG_APUS */ mtspr SPRN_DBAT0L,r8 /* N.B. 6xx (not 601) have valid */ mtspr SPRN_DBAT0U,r11 /* bit in upper BAT register */ @@ -1245,7 +1136,7 @@ initial_bats: isync blr -#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) +#ifdef CONFIG_BOOTX_TEXT setup_disp_bat: /* * setup the display bat prepared for us in prom.c @@ -1268,7 +1159,7 @@ setup_disp_bat: mtspr SPRN_IBAT3U,r11 blr -#endif /* !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) */ +#endif /* defined(CONFIG_BOOTX_TEXT) */ #ifdef CONFIG_8260 /* Jump into the system reset for the rom. |