diff options
Diffstat (limited to 'arch/ppc/platforms/4xx/yucca.h')
-rw-r--r-- | arch/ppc/platforms/4xx/yucca.h | 108 |
1 files changed, 0 insertions, 108 deletions
diff --git a/arch/ppc/platforms/4xx/yucca.h b/arch/ppc/platforms/4xx/yucca.h deleted file mode 100644 index bc9684e66a8..00000000000 --- a/arch/ppc/platforms/4xx/yucca.h +++ /dev/null @@ -1,108 +0,0 @@ -/* - * Yucca board definitions - * - * Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter) - * - * Copyright 2004-2005 MontaVista Software Inc. - * Copyright (c) 2005 Cisco Systems. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - */ - -#ifdef __KERNEL__ -#ifndef __ASM_YUCCA_H__ -#define __ASM_YUCCA_H__ - -#include <platforms/4xx/ppc440spe.h> - -/* F/W TLB mapping used in bootloader glue to reset EMAC */ -#define PPC44x_EMAC0_MR0 0xa0000800 - -/* Location of MAC addresses in PIBS image */ -#define PIBS_FLASH_BASE 0xffe00000 -#define PIBS_MAC_BASE (PIBS_FLASH_BASE+0x1b0400) - -/* External timer clock frequency */ -#define YUCCA_TMR_CLK 25000000 - -/* - * FPGA registers - */ -#define YUCCA_FPGA_REG_BASE 0x00000004e2000000ULL -#define YUCCA_FPGA_REG_SIZE 0x24 - -#define FPGA_REG1A 0x1a - -#define FPGA_REG1A_PE0_GLED 0x8000 -#define FPGA_REG1A_PE1_GLED 0x4000 -#define FPGA_REG1A_PE2_GLED 0x2000 -#define FPGA_REG1A_PE0_YLED 0x1000 -#define FPGA_REG1A_PE1_YLED 0x0800 -#define FPGA_REG1A_PE2_YLED 0x0400 -#define FPGA_REG1A_PE0_PWRON 0x0200 -#define FPGA_REG1A_PE1_PWRON 0x0100 -#define FPGA_REG1A_PE2_PWRON 0x0080 -#define FPGA_REG1A_PE0_REFCLK_ENABLE 0x0040 -#define FPGA_REG1A_PE1_REFCLK_ENABLE 0x0020 -#define FPGA_REG1A_PE2_REFCLK_ENABLE 0x0010 -#define FPGA_REG1A_PE_SPREAD0 0x0008 -#define FPGA_REG1A_PE_SPREAD1 0x0004 -#define FPGA_REG1A_PE_SELSOURCE_0 0x0002 -#define FPGA_REG1A_PE_SELSOURCE_1 0x0001 - -#define FPGA_REG1C 0x1c - -#define FPGA_REG1C_PE0_ROOTPOINT 0x8000 -#define FPGA_REG1C_PE1_ENDPOINT 0x4000 -#define FPGA_REG1C_PE2_ENDPOINT 0x2000 -#define FPGA_REG1C_PE0_PRSNT 0x1000 -#define FPGA_REG1C_PE1_PRSNT 0x0800 -#define FPGA_REG1C_PE2_PRSNT 0x0400 -#define FPGA_REG1C_PE0_WAKE 0x0080 -#define FPGA_REG1C_PE1_WAKE 0x0040 -#define FPGA_REG1C_PE2_WAKE 0x0020 -#define FPGA_REG1C_PE0_PERST 0x0010 -#define FPGA_REG1C_PE1_PERST 0x0008 -#define FPGA_REG1C_PE2_PERST 0x0004 - -/* - * Serial port defines - */ -#define RS_TABLE_SIZE 3 - -/* PIBS defined UART mappings, used before early_serial_setup */ -#define UART0_IO_BASE 0xa0000200 -#define UART1_IO_BASE 0xa0000300 -#define UART2_IO_BASE 0xa0000600 - -#define BASE_BAUD 11059200 -#define STD_UART_OP(num) \ - { 0, BASE_BAUD, 0, UART##num##_INT, \ - (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \ - iomem_base: (void*)UART##num##_IO_BASE, \ - io_type: SERIAL_IO_MEM}, - -#define SERIAL_PORT_DFNS \ - STD_UART_OP(0) \ - STD_UART_OP(1) \ - STD_UART_OP(2) - -/* PCI support */ -#define YUCCA_PCIX_LOWER_IO 0x00000000 -#define YUCCA_PCIX_UPPER_IO 0x0000ffff -#define YUCCA_PCIX_LOWER_MEM 0x80000000 -#define YUCCA_PCIX_UPPER_MEM 0x8fffffff -#define YUCCA_PCIE_LOWER_MEM 0x90000000 -#define YUCCA_PCIE_MEM_SIZE 0x10000000 - -#define YUCCA_PCIX_MEM_SIZE 0x10000000 -#define YUCCA_PCIX_MEM_OFFSET 0x00000000 -#define YUCCA_PCIE_MEM_SIZE 0x10000000 -#define YUCCA_PCIE_MEM_OFFSET 0x00000000 - -#endif /* __ASM_YUCCA_H__ */ -#endif /* __KERNEL__ */ |