diff options
Diffstat (limited to 'arch/sh/boards/superh/microdev/io.c')
| -rw-r--r-- | arch/sh/boards/superh/microdev/io.c | 370 |
1 files changed, 370 insertions, 0 deletions
diff --git a/arch/sh/boards/superh/microdev/io.c b/arch/sh/boards/superh/microdev/io.c new file mode 100644 index 00000000000..fe83b2c0307 --- /dev/null +++ b/arch/sh/boards/superh/microdev/io.c @@ -0,0 +1,370 @@ +/* + * linux/arch/sh/kernel/io_microdev.c + * + * Copyright (C) 2003 Sean McGoogan (Sean.McGoogan@superh.com) + * Copyright (C) 2003, 2004 SuperH, Inc. + * Copyright (C) 2004 Paul Mundt + * + * SuperH SH4-202 MicroDev board support. + * + * May be copied or modified under the terms of the GNU General Public + * License. See linux/COPYING for more information. + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/pci.h> +#include <linux/wait.h> +#include <asm/io.h> +#include <asm/mach/io.h> + + /* + * we need to have a 'safe' address to re-direct all I/O requests + * that we do not explicitly wish to handle. This safe address + * must have the following properies: + * + * * writes are ignored (no exception) + * * reads are benign (no side-effects) + * * accesses of width 1, 2 and 4-bytes are all valid. + * + * The Processor Version Register (PVR) has these properties. + */ +#define PVR 0xff000030 /* Processor Version Register */ + + +#define IO_IDE2_BASE 0x170ul /* I/O base for SMSC FDC37C93xAPM IDE #2 */ +#define IO_IDE1_BASE 0x1f0ul /* I/O base for SMSC FDC37C93xAPM IDE #1 */ +#define IO_ISP1161_BASE 0x290ul /* I/O port for Philips ISP1161x USB chip */ +#define IO_SERIAL2_BASE 0x2f8ul /* I/O base for SMSC FDC37C93xAPM Serial #2 */ +#define IO_LAN91C111_BASE 0x300ul /* I/O base for SMSC LAN91C111 Ethernet chip */ +#define IO_IDE2_MISC 0x376ul /* I/O misc for SMSC FDC37C93xAPM IDE #2 */ +#define IO_SUPERIO_BASE 0x3f0ul /* I/O base for SMSC FDC37C93xAPM SuperIO chip */ +#define IO_IDE1_MISC 0x3f6ul /* I/O misc for SMSC FDC37C93xAPM IDE #1 */ +#define IO_SERIAL1_BASE 0x3f8ul /* I/O base for SMSC FDC37C93xAPM Serial #1 */ + +#define IO_ISP1161_EXTENT 0x04ul /* I/O extent for Philips ISP1161x USB chip */ +#define IO_LAN91C111_EXTENT 0x10ul /* I/O extent for SMSC LAN91C111 Ethernet chip */ +#define IO_SUPERIO_EXTENT 0x02ul /* I/O extent for SMSC FDC37C93xAPM SuperIO chip */ +#define IO_IDE_EXTENT 0x08ul /* I/O extent for IDE Task Register set */ +#define IO_SERIAL_EXTENT 0x10ul + +#define IO_LAN91C111_PHYS 0xa7500000ul /* Physical address of SMSC LAN91C111 Ethernet chip */ +#define IO_ISP1161_PHYS 0xa7700000ul /* Physical address of Philips ISP1161x USB chip */ +#define IO_SUPERIO_PHYS 0xa7800000ul /* Physical address of SMSC FDC37C93xAPM SuperIO chip */ + +#define PORT2ADDR(x) (microdev_isa_port2addr(x)) + + +static inline void delay(void) +{ +#if defined(CONFIG_PCI) + /* System board present, just make a dummy SRAM access. (CS0 will be + mapped to PCI memory, probably good to avoid it.) */ + ctrl_inw(0xa6800000); +#else + /* CS0 will be mapped to flash, ROM etc so safe to access it. */ + ctrl_inw(0xa0000000); +#endif +} + +unsigned char microdev_inb(unsigned long port) +{ +#ifdef CONFIG_PCI + if (port >= PCIBIOS_MIN_IO) + return microdev_pci_inb(port); +#endif + return *(volatile unsigned char*)PORT2ADDR(port); +} + +unsigned short microdev_inw(unsigned long port) +{ +#ifdef CONFIG_PCI + if (port >= PCIBIOS_MIN_IO) + return microdev_pci_inw(port); +#endif + return *(volatile unsigned short*)PORT2ADDR(port); +} + +unsigned int microdev_inl(unsigned long port) +{ +#ifdef CONFIG_PCI + if (port >= PCIBIOS_MIN_IO) + return microdev_pci_inl(port); +#endif + return *(volatile unsigned int*)PORT2ADDR(port); +} + +void microdev_outb(unsigned char b, unsigned long port) +{ +#ifdef CONFIG_PCI + if (port >= PCIBIOS_MIN_IO) { + microdev_pci_outb(b, port); + return; + } +#endif + + /* + * There is a board feature with the current SH4-202 MicroDev in + * that the 2 byte enables (nBE0 and nBE1) are tied together (and + * to the Chip Select Line (Ethernet_CS)). Due to this conectivity, + * it is not possible to safely perform 8-bit writes to the + * Ethernet registers, as 16-bits will be consumed from the Data + * lines (corrupting the other byte). Hence, this function is + * written to impliment 16-bit read/modify/write for all byte-wide + * acceses. + * + * Note: there is no problem with byte READS (even or odd). + * + * Sean McGoogan - 16th June 2003. + */ + if ((port >= IO_LAN91C111_BASE) && + (port < IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) { + /* + * Then are trying to perform a byte-write to the + * LAN91C111. This needs special care. + */ + if (port % 2 == 1) { /* is the port odd ? */ + /* unset bit-0, i.e. make even */ + const unsigned long evenPort = port-1; + unsigned short word; + + /* + * do a 16-bit read/write to write to 'port', + * preserving even byte. + * + * Even addresses are bits 0-7 + * Odd addresses are bits 8-15 + */ + word = microdev_inw(evenPort); + word = (word & 0xffu) | (b << 8); + microdev_outw(word, evenPort); + } else { + /* else, we are trying to do an even byte write */ + unsigned short word; + + /* + * do a 16-bit read/write to write to 'port', + * preserving odd byte. + * + * Even addresses are bits 0-7 + * Odd addresses are bits 8-15 + */ + word = microdev_inw(port); + word = (word & 0xff00u) | (b); + microdev_outw(word, port); + } + } else { + *(volatile unsigned char*)PORT2ADDR(port) = b; + } +} + +void microdev_outw(unsigned short b, unsigned long port) +{ +#ifdef CONFIG_PCI + if (port >= PCIBIOS_MIN_IO) { + microdev_pci_outw(b, port); + return; + } +#endif + *(volatile unsigned short*)PORT2ADDR(port) = b; +} + +void microdev_outl(unsigned int b, unsigned long port) +{ +#ifdef CONFIG_PCI + if (port >= PCIBIOS_MIN_IO) { + microdev_pci_outl(b, port); + return; + } +#endif + *(volatile unsigned int*)PORT2ADDR(port) = b; +} + +unsigned char microdev_inb_p(unsigned long port) +{ + unsigned char v = microdev_inb(port); + delay(); + return v; +} + +unsigned short microdev_inw_p(unsigned long port) +{ + unsigned short v = microdev_inw(port); + delay(); + return v; +} + +unsigned int microdev_inl_p(unsigned long port) +{ + unsigned int v = microdev_inl(port); + delay(); + return v; +} + +void microdev_outb_p(unsigned char b, unsigned long port) +{ + microdev_outb(b, port); + delay(); +} + +void microdev_outw_p(unsigned short b, unsigned long port) +{ + microdev_outw(b, port); + delay(); +} + +void microdev_outl_p(unsigned int b, unsigned long port) +{ + microdev_outl(b, port); + delay(); +} + +void microdev_insb(unsigned long port, void *buffer, unsigned long count) +{ + volatile unsigned char *port_addr; + unsigned char *buf = buffer; + + port_addr = (volatile unsigned char *)PORT2ADDR(port); + + while (count--) + *buf++ = *port_addr; +} + +void microdev_insw(unsigned long port, void *buffer, unsigned long count) +{ + volatile unsigned short *port_addr; + unsigned short *buf = buffer; + + port_addr = (volatile unsigned short *)PORT2ADDR(port); + + while (count--) + *buf++ = *port_addr; +} + +void microdev_insl(unsigned long port, void *buffer, unsigned long count) +{ + volatile unsigned long *port_addr; + unsigned int *buf = buffer; + + port_addr = (volatile unsigned long *)PORT2ADDR(port); + + while (count--) + *buf++ = *port_addr; +} + +void microdev_outsb(unsigned long port, const void *buffer, unsigned long count) +{ + volatile unsigned char *port_addr; + const unsigned char *buf = buffer; + + port_addr = (volatile unsigned char *)PORT2ADDR(port); + + while (count--) + *port_addr = *buf++; +} + +void microdev_outsw(unsigned long port, const void *buffer, unsigned long count) +{ + volatile unsigned short *port_addr; + const unsigned short *buf = buffer; + + port_addr = (volatile unsigned short *)PORT2ADDR(port); + + while (count--) + *port_addr = *buf++; +} + +void microdev_outsl(unsigned long port, const void *buffer, unsigned long count) +{ + volatile unsigned long *port_addr; + const unsigned int *buf = buffer; + + port_addr = (volatile unsigned long *)PORT2ADDR(port); + + while (count--) + *port_addr = *buf++; +} + +/* + * map I/O ports to memory-mapped addresses + */ +unsigned long microdev_isa_port2addr(unsigned long offset) +{ + unsigned long result; + + if ((offset >= IO_LAN91C111_BASE) && + (offset < IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) { + /* + * SMSC LAN91C111 Ethernet chip + */ + result = IO_LAN91C111_PHYS + offset - IO_LAN91C111_BASE; + } else if ((offset >= IO_SUPERIO_BASE) && + (offset < IO_SUPERIO_BASE + IO_SUPERIO_EXTENT)) { + /* + * SMSC FDC37C93xAPM SuperIO chip + * + * Configuration Registers + */ + result = IO_SUPERIO_PHYS + (offset << 1); +#if 0 + } else if (offset == KBD_DATA_REG || offset == KBD_CNTL_REG || + offset == KBD_STATUS_REG) { + /* + * SMSC FDC37C93xAPM SuperIO chip + * + * PS/2 Keyboard + Mouse (ports 0x60 and 0x64). + */ + result = IO_SUPERIO_PHYS + (offset << 1); +#endif + } else if (((offset >= IO_IDE1_BASE) && + (offset < IO_IDE1_BASE + IO_IDE_EXTENT)) || + (offset == IO_IDE1_MISC)) { + /* + * SMSC FDC37C93xAPM SuperIO chip + * + * IDE #1 + */ + result = IO_SUPERIO_PHYS + (offset << 1); + } else if (((offset >= IO_IDE2_BASE) && + (offset < IO_IDE2_BASE + IO_IDE_EXTENT)) || + (offset == IO_IDE2_MISC)) { + /* + * SMSC FDC37C93xAPM SuperIO chip + * + * IDE #2 + */ + result = IO_SUPERIO_PHYS + (offset << 1); + } else if ((offset >= IO_SERIAL1_BASE) && + (offset < IO_SERIAL1_BASE + IO_SERIAL_EXTENT)) { + /* + * SMSC FDC37C93xAPM SuperIO chip + * + * Serial #1 + */ + result = IO_SUPERIO_PHYS + (offset << 1); + } else if ((offset >= IO_SERIAL2_BASE) && + (offset < IO_SERIAL2_BASE + IO_SERIAL_EXTENT)) { + /* + * SMSC FDC37C93xAPM SuperIO chip + * + * Serial #2 + */ + result = IO_SUPERIO_PHYS + (offset << 1); + } else if ((offset >= IO_ISP1161_BASE) && + (offset < IO_ISP1161_BASE + IO_ISP1161_EXTENT)) { + /* + * Philips USB ISP1161x chip + */ + result = IO_ISP1161_PHYS + offset - IO_ISP1161_BASE; + } else { + /* + * safe default. + */ + printk("Warning: unexpected port in %s( offset = 0x%lx )\n", + __FUNCTION__, offset); + result = PVR; + } + + return result; +} + |