3 files changed, 12 insertions, 71 deletions

diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index 2eaeb9e5958..f48c492a68d 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -720,32 +720,6 @@ static struct platform_device camera_devices[] = {
 };
 
 /* FSI */
-/*
- * FSI-B use external clock which came from da7210.
- * So, we should change parent of fsi
- */
-#define FCLKBCR		0xa415000c
-static void fsimck_init(struct clk *clk)
-{
-	u32 status = __raw_readl(clk->enable_reg);
-
-	/* use external clock */
-	status &= ~0x000000ff;
-	status |= 0x00000080;
-
-	__raw_writel(status, clk->enable_reg);
-}
-
-static struct clk_ops fsimck_clk_ops = {
-	.init = fsimck_init,
-};
-
-static struct clk fsimckb_clk = {
-	.ops		= &fsimck_clk_ops,
-	.enable_reg	= (void __iomem *)FCLKBCR,
-	.rate		= 0, /* unknown */
-};
-
 static struct sh_fsi_platform_info fsi_info = {
 	.portb_flags = SH_FSI_BRS_INV |
 		       SH_FSI_OUT_SLAVE_MODE |
@@ -1264,10 +1238,10 @@ static int __init arch_setup(void)
 	/* change parent of FSI B */
 	clk = clk_get(NULL, "fsib_clk");
 	if (!IS_ERR(clk)) {
-		clk_register(&fsimckb_clk);
-		clk_set_parent(clk, &fsimckb_clk);
-		clk_set_rate(clk, 11000);
-		clk_set_rate(&fsimckb_clk, 11000);
+		/* 48kHz dummy clock was used to make sure 1/1 divide */
+		clk_set_rate(&sh7724_fsimckb_clk, 48000);
+		clk_set_parent(clk, &sh7724_fsimckb_clk);
+		clk_set_rate(clk, 48000);
 		clk_put(clk);
 	}
 
diff --git a/arch/sh/boards/mach-se/7206/irq.c b/arch/sh/boards/mach-se/7206/irq.c
index d961949600f..9070d7e6070 100644
--- a/arch/sh/boards/mach-se/7206/irq.c
+++ b/arch/sh/boards/mach-se/7206/irq.c
@@ -140,7 +140,7 @@ void __init init_se7206_IRQ(void)
 	make_se7206_irq(IRQ1_IRQ); /* ATA */
 	make_se7206_irq(IRQ3_IRQ); /* SLOT / PCM */
 
-	__raw_writew(__raw_readw(INTC_ICR1) | 0x000b, INTC_ICR); /* ICR1 */
+	__raw_writew(__raw_readw(INTC_ICR1) | 0x000b, INTC_ICR1); /* ICR1 */
 
 	/* FPGA System register setup*/
 	__raw_writew(0x0000,INTSTS0); /* Clear INTSTS0 */
diff --git a/arch/sh/boards/mach-se/7724/setup.c b/arch/sh/boards/mach-se/7724/setup.c
index c31d228fdfc..527a0cd956b 100644
--- a/arch/sh/boards/mach-se/7724/setup.c
+++ b/arch/sh/boards/mach-se/7724/setup.c
@@ -283,31 +283,6 @@ static struct platform_device ceu1_device = {
 };
 
 /* FSI */
-/*
- * FSI-A use external clock which came from ak464x.
- * So, we should change parent of fsi
- */
-#define FCLKACR		0xa4150008
-static void fsimck_init(struct clk *clk)
-{
-	u32 status = __raw_readl(clk->enable_reg);
-
-	/* use external clock */
-	status &= ~0x000000ff;
-	status |= 0x00000080;
-	__raw_writel(status, clk->enable_reg);
-}
-
-static struct clk_ops fsimck_clk_ops = {
-	.init = fsimck_init,
-};
-
-static struct clk fsimcka_clk = {
-	.ops		= &fsimck_clk_ops,
-	.enable_reg	= (void __iomem *)FCLKACR,
-	.rate		= 0, /* unknown */
-};
-
 /* change J20, J21, J22 pin to 1-2 connection to use slave mode */
 static struct sh_fsi_platform_info fsi_info = {
 	.porta_flags = SH_FSI_BRS_INV |
@@ -852,37 +827,29 @@ static int __init devices_setup(void)
 	gpio_request(GPIO_FN_KEYOUT0,     NULL);
 
 	/* enable FSI */
-	gpio_request(GPIO_FN_FSIMCKB,    NULL);
 	gpio_request(GPIO_FN_FSIMCKA,    NULL);
+	gpio_request(GPIO_FN_FSIIASD,    NULL);
 	gpio_request(GPIO_FN_FSIOASD,    NULL);
 	gpio_request(GPIO_FN_FSIIABCK,   NULL);
 	gpio_request(GPIO_FN_FSIIALRCK,  NULL);
 	gpio_request(GPIO_FN_FSIOABCK,   NULL);
 	gpio_request(GPIO_FN_FSIOALRCK,  NULL);
 	gpio_request(GPIO_FN_CLKAUDIOAO, NULL);
-	gpio_request(GPIO_FN_FSIIBSD,    NULL);
-	gpio_request(GPIO_FN_FSIOBSD,    NULL);
-	gpio_request(GPIO_FN_FSIIBBCK,   NULL);
-	gpio_request(GPIO_FN_FSIIBLRCK,  NULL);
-	gpio_request(GPIO_FN_FSIOBBCK,   NULL);
-	gpio_request(GPIO_FN_FSIOBLRCK,  NULL);
-	gpio_request(GPIO_FN_CLKAUDIOBO, NULL);
-	gpio_request(GPIO_FN_FSIIASD,    NULL);
 
 	/* set SPU2 clock to 83.4 MHz */
 	clk = clk_get(NULL, "spu_clk");
-	if (clk) {
+	if (!IS_ERR(clk)) {
 		clk_set_rate(clk, clk_round_rate(clk, 83333333));
 		clk_put(clk);
 	}
 
 	/* change parent of FSI A */
 	clk = clk_get(NULL, "fsia_clk");
-	if (clk) {
-		clk_register(&fsimcka_clk);
-		clk_set_parent(clk, &fsimcka_clk);
-		clk_set_rate(clk, 11000);
-		clk_set_rate(&fsimcka_clk, 11000);
+	if (!IS_ERR(clk)) {
+		/* 48kHz dummy clock was used to make sure 1/1 divide */
+		clk_set_rate(&sh7724_fsimcka_clk, 48000);
+		clk_set_parent(clk, &sh7724_fsimcka_clk);
+		clk_set_rate(clk, 48000);
 		clk_put(clk);
 	}