diff options
Diffstat (limited to 'arch/v850/kernel/as85ep1.c')
| -rw-r--r-- | arch/v850/kernel/as85ep1.c | 234 |
1 files changed, 0 insertions, 234 deletions
diff --git a/arch/v850/kernel/as85ep1.c b/arch/v850/kernel/as85ep1.c deleted file mode 100644 index b525ecf3aea..00000000000 --- a/arch/v850/kernel/as85ep1.c +++ /dev/null @@ -1,234 +0,0 @@ -/* - * arch/v850/kernel/as85ep1.c -- AS85EP1 V850E evaluation chip/board - * - * Copyright (C) 2002,03 NEC Electronics Corporation - * Copyright (C) 2002,03 Miles Bader <miles@gnu.org> - * - * This file is subject to the terms and conditions of the GNU General - * Public License. See the file COPYING in the main directory of this - * archive for more details. - * - * Written by Miles Bader <miles@gnu.org> - */ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/bootmem.h> -#include <linux/major.h> -#include <linux/irq.h> - -#include <asm/machdep.h> -#include <asm/atomic.h> -#include <asm/page.h> -#include <asm/v850e_timer_d.h> -#include <asm/v850e_uart.h> - -#include "mach.h" - - -/* SRAM and SDRAM are vaguely contiguous (with a big hole in between; see - mach_reserve_bootmem for details); use both as one big area. */ -#define RAM_START SRAM_ADDR -#define RAM_END (SDRAM_ADDR + SDRAM_SIZE) - -/* The bits of this port are connected to an 8-LED bar-graph. */ -#define LEDS_PORT 4 - - -static void as85ep1_led_tick (void); - -extern char _intv_copy_src_start, _intv_copy_src_end; -extern char _intv_copy_dst_start; - - -void __init mach_early_init (void) -{ -#ifndef CONFIG_ROM_KERNEL - const u32 *src; - register u32 *dst asm ("ep"); -#endif - - AS85EP1_CSC(0) = 0x0403; - AS85EP1_BCT(0) = 0xB8B8; - AS85EP1_DWC(0) = 0x0104; - AS85EP1_BCC = 0x0012; - AS85EP1_ASC = 0; - AS85EP1_LBS = 0x00A9; - - AS85EP1_PORT_PMC(6) = 0xFF; /* valid A0,A1,A20-A25 */ - AS85EP1_PORT_PMC(7) = 0x0E; /* valid CS1-CS3 */ - AS85EP1_PORT_PMC(9) = 0xFF; /* valid D16-D23 */ - AS85EP1_PORT_PMC(10) = 0xFF; /* valid D24-D31 */ - - AS85EP1_RFS(1) = 0x800c; - AS85EP1_RFS(3) = 0x800c; - AS85EP1_SCR(1) = 0x20A9; - AS85EP1_SCR(3) = 0x20A9; - -#ifndef CONFIG_ROM_KERNEL - /* The early chip we have is buggy, and writing the interrupt - vectors into low RAM may screw up, so for non-ROM kernels, we - only rely on the reset vector being downloaded, and copy the - rest of the interrupt vectors into place here. The specific bug - is that writing address N, where (N & 0x10) == 0x10, will _also_ - write to address (N - 0x10). We avoid this (effectively) by - writing in 16-byte chunks backwards from the end. */ - - AS85EP1_IRAMM = 0x3; /* "write-mode" for the internal instruction memory */ - - src = (u32 *)(((u32)&_intv_copy_src_end - 1) & ~0xF); - dst = (u32 *)&_intv_copy_dst_start - + (src - (u32 *)&_intv_copy_src_start); - do { - u32 t0 = src[0], t1 = src[1], t2 = src[2], t3 = src[3]; - dst[0] = t0; dst[1] = t1; dst[2] = t2; dst[3] = t3; - dst -= 4; - src -= 4; - } while (src > (u32 *)&_intv_copy_src_start); - - AS85EP1_IRAMM = 0x0; /* "read-mode" for the internal instruction memory */ -#endif /* !CONFIG_ROM_KERNEL */ - - v850e_intc_disable_irqs (); -} - -void __init mach_setup (char **cmdline) -{ - AS85EP1_PORT_PMC (LEDS_PORT) = 0; /* Make the LEDs port an I/O port. */ - AS85EP1_PORT_PM (LEDS_PORT) = 0; /* Make all the bits output pins. */ - mach_tick = as85ep1_led_tick; -} - -void __init mach_get_physical_ram (unsigned long *ram_start, - unsigned long *ram_len) -{ - *ram_start = RAM_START; - *ram_len = RAM_END - RAM_START; -} - -/* Convenience macros. */ -#define SRAM_END (SRAM_ADDR + SRAM_SIZE) -#define SDRAM_END (SDRAM_ADDR + SDRAM_SIZE) - -void __init mach_reserve_bootmem () -{ - if (SDRAM_ADDR < RAM_END && SDRAM_ADDR > RAM_START) - /* We can't use the space between SRAM and SDRAM, so - prevent the kernel from trying. */ - reserve_bootmem(SRAM_END, SDRAM_ADDR - SRAM_END, - BOOTMEM_DEFAULT); -} - -void mach_gettimeofday (struct timespec *tv) -{ - tv->tv_sec = 0; - tv->tv_nsec = 0; -} - -void __init mach_sched_init (struct irqaction *timer_action) -{ - /* Start hardware timer. */ - v850e_timer_d_configure (0, HZ); - /* Install timer interrupt handler. */ - setup_irq (IRQ_INTCMD(0), timer_action); -} - -static struct v850e_intc_irq_init irq_inits[] = { - { "IRQ", 0, NUM_MACH_IRQS, 1, 7 }, - { "CCC", IRQ_INTCCC(0), IRQ_INTCCC_NUM, 1, 5 }, - { "CMD", IRQ_INTCMD(0), IRQ_INTCMD_NUM, 1, 5 }, - { "SRE", IRQ_INTSRE(0), IRQ_INTSRE_NUM, 3, 3 }, - { "SR", IRQ_INTSR(0), IRQ_INTSR_NUM, 3, 4 }, - { "ST", IRQ_INTST(0), IRQ_INTST_NUM, 3, 5 }, - { 0 } -}; -#define NUM_IRQ_INITS (ARRAY_SIZE(irq_inits) - 1) - -static struct hw_interrupt_type hw_itypes[NUM_IRQ_INITS]; - -void __init mach_init_irqs (void) -{ - v850e_intc_init_irq_types (irq_inits, hw_itypes); -} - -void machine_restart (char *__unused) -{ -#ifdef CONFIG_RESET_GUARD - disable_reset_guard (); -#endif - asm ("jmp r0"); /* Jump to the reset vector. */ -} - -void machine_halt (void) -{ -#ifdef CONFIG_RESET_GUARD - disable_reset_guard (); -#endif - local_irq_disable (); /* Ignore all interrupts. */ - AS85EP1_PORT_IO (LEDS_PORT) = 0xAA; /* Note that we halted. */ - for (;;) - asm ("halt; nop; nop; nop; nop; nop"); -} - -void machine_power_off (void) -{ - machine_halt (); -} - -/* Called before configuring an on-chip UART. */ -void as85ep1_uart_pre_configure (unsigned chan, unsigned cflags, unsigned baud) -{ - /* Make the shared uart/port pins be uart pins. */ - AS85EP1_PORT_PMC(3) |= (0x5 << chan); - - /* The AS85EP1 connects some general-purpose I/O pins on the CPU to - the RTS/CTS lines of UART 1's serial connection. I/O pins P53 - and P54 are RTS and CTS respectively. */ - if (chan == 1) { - /* Put P53 & P54 in I/O port mode. */ - AS85EP1_PORT_PMC(5) &= ~0x18; - /* Make P53 an output, and P54 an input. */ - AS85EP1_PORT_PM(5) |= 0x10; - } -} - -/* Minimum and maximum bounds for the moving upper LED boundary in the - clock tick display. */ -#define MIN_MAX_POS 0 -#define MAX_MAX_POS 7 - -/* There are MAX_MAX_POS^2 - MIN_MAX_POS^2 cycles in the animation, so if - we pick 6 and 0 as above, we get 49 cycles, which is when divided into - the standard 100 value for HZ, gives us an almost 1s total time. */ -#define TICKS_PER_FRAME \ - (HZ / (MAX_MAX_POS * MAX_MAX_POS - MIN_MAX_POS * MIN_MAX_POS)) - -static void as85ep1_led_tick () -{ - static unsigned counter = 0; - - if (++counter == TICKS_PER_FRAME) { - static int pos = 0, max_pos = MAX_MAX_POS, dir = 1; - - if (dir > 0 && pos == max_pos) { - dir = -1; - if (max_pos == MIN_MAX_POS) - max_pos = MAX_MAX_POS; - else - max_pos--; - } else { - if (dir < 0 && pos == 0) - dir = 1; - - if (pos + dir <= max_pos) { - /* Each bit of port 0 has a LED. */ - set_bit (pos, &AS85EP1_PORT_IO(LEDS_PORT)); - pos += dir; - clear_bit (pos, &AS85EP1_PORT_IO(LEDS_PORT)); - } - } - - counter = 0; - } -} |