diff options
Diffstat (limited to 'arch/x86/mach-visws')
| -rw-r--r-- | arch/x86/mach-visws/Makefile | 7 | ||||
| -rw-r--r-- | arch/x86/mach-visws/setup.c | 174 | ||||
| -rw-r--r-- | arch/x86/mach-visws/setup_visws.c | 331 | ||||
| -rw-r--r-- | arch/x86/mach-visws/traps.c | 71 | ||||
| -rw-r--r-- | arch/x86/mach-visws/visws_apic.c | 295 |
5 files changed, 0 insertions, 878 deletions
diff --git a/arch/x86/mach-visws/Makefile b/arch/x86/mach-visws/Makefile deleted file mode 100644 index 7469df1340c..00000000000 --- a/arch/x86/mach-visws/Makefile +++ /dev/null @@ -1,7 +0,0 @@ -# -# Makefile for the linux kernel. -# - -obj-y := setup.o setup_visws.o traps.o - -obj-$(CONFIG_X86_VISWS_APIC) += visws_apic.o diff --git a/arch/x86/mach-visws/setup.c b/arch/x86/mach-visws/setup.c deleted file mode 100644 index b8054c3ffce..00000000000 --- a/arch/x86/mach-visws/setup.c +++ /dev/null @@ -1,174 +0,0 @@ -/* - * Machine specific setup for generic - */ - -#include <linux/smp.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <asm/acpi.h> -#include <asm/arch_hooks.h> -#include <asm/e820.h> -#include <asm/setup.h> - -/* - * Any quirks to be performed to initialize timers/irqs/etc? - */ -int (*arch_time_init_quirk)(void); -int (*arch_pre_intr_init_quirk)(void); -int (*arch_intr_init_quirk)(void); -int (*arch_trap_init_quirk)(void); - -#ifdef CONFIG_HOTPLUG_CPU -#define DEFAULT_SEND_IPI (1) -#else -#define DEFAULT_SEND_IPI (0) -#endif - -int no_broadcast=DEFAULT_SEND_IPI; - -/** - * pre_intr_init_hook - initialisation prior to setting up interrupt vectors - * - * Description: - * Perform any necessary interrupt initialisation prior to setting up - * the "ordinary" interrupt call gates. For legacy reasons, the ISA - * interrupts should be initialised here if the machine emulates a PC - * in any way. - **/ -void __init pre_intr_init_hook(void) -{ - if (arch_pre_intr_init_quirk) { - if (arch_pre_intr_init_quirk()) - return; - } - init_ISA_irqs(); -} - -/* - * IRQ2 is cascade interrupt to second interrupt controller - */ -static struct irqaction irq2 = { - .handler = no_action, - .mask = CPU_MASK_NONE, - .name = "cascade", -}; - -/** - * intr_init_hook - post gate setup interrupt initialisation - * - * Description: - * Fill in any interrupts that may have been left out by the general - * init_IRQ() routine. interrupts having to do with the machine rather - * than the devices on the I/O bus (like APIC interrupts in intel MP - * systems) are started here. - **/ -void __init intr_init_hook(void) -{ - if (arch_intr_init_quirk) { - if (arch_intr_init_quirk()) - return; - } -#ifdef CONFIG_X86_LOCAL_APIC - apic_intr_init(); -#endif - - if (!acpi_ioapic) - setup_irq(2, &irq2); -} - -/** - * pre_setup_arch_hook - hook called prior to any setup_arch() execution - * - * Description: - * generally used to activate any machine specific identification - * routines that may be needed before setup_arch() runs. On VISWS - * this is used to get the board revision and type. - **/ -void __init pre_setup_arch_hook(void) -{ -} - -/** - * trap_init_hook - initialise system specific traps - * - * Description: - * Called as the final act of trap_init(). Used in VISWS to initialise - * the various board specific APIC traps. - **/ -void __init trap_init_hook(void) -{ - if (arch_trap_init_quirk) { - if (arch_trap_init_quirk()) - return; - } -} - -static struct irqaction irq0 = { - .handler = timer_interrupt, - .flags = IRQF_DISABLED | IRQF_NOBALANCING | IRQF_IRQPOLL, - .mask = CPU_MASK_NONE, - .name = "timer" -}; - -/** - * time_init_hook - do any specific initialisations for the system timer. - * - * Description: - * Must plug the system timer interrupt source at HZ into the IRQ listed - * in irq_vectors.h:TIMER_IRQ - **/ -void __init time_init_hook(void) -{ - if (arch_time_init_quirk) { - /* - * A nonzero return code does not mean failure, it means - * that the architecture quirk does not want any - * generic (timer) setup to be performed after this: - */ - if (arch_time_init_quirk()) - return; - } - - irq0.mask = cpumask_of_cpu(0); - setup_irq(0, &irq0); -} - -#ifdef CONFIG_MCA -/** - * mca_nmi_hook - hook into MCA specific NMI chain - * - * Description: - * The MCA (Microchannel Architecture) has an NMI chain for NMI sources - * along the MCA bus. Use this to hook into that chain if you will need - * it. - **/ -void mca_nmi_hook(void) -{ - /* If I recall correctly, there's a whole bunch of other things that - * we can do to check for NMI problems, but that's all I know about - * at the moment. - */ - - printk("NMI generated from unknown source!\n"); -} -#endif - -static __init int no_ipi_broadcast(char *str) -{ - get_option(&str, &no_broadcast); - printk ("Using %s mode\n", no_broadcast ? "No IPI Broadcast" : - "IPI Broadcast"); - return 1; -} - -__setup("no_ipi_broadcast=", no_ipi_broadcast); - -static int __init print_ipi_mode(void) -{ - printk ("Using IPI %s mode\n", no_broadcast ? "No-Shortcut" : - "Shortcut"); - return 0; -} - -late_initcall(print_ipi_mode); - diff --git a/arch/x86/mach-visws/setup_visws.c b/arch/x86/mach-visws/setup_visws.c deleted file mode 100644 index e95e9499c8c..00000000000 --- a/arch/x86/mach-visws/setup_visws.c +++ /dev/null @@ -1,331 +0,0 @@ -/* - * Unmaintained SGI Visual Workstation support. - * Split out from setup.c by davej@suse.de - */ - -#include <linux/interrupt.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/smp.h> - -#include <asm/visws/cobalt.h> -#include <asm/visws/piix4.h> -#include <asm/arch_hooks.h> -#include <asm/fixmap.h> -#include <asm/reboot.h> -#include <asm/setup.h> -#include <asm/e820.h> -#include <asm/smp.h> -#include <asm/io.h> - -#include <mach_ipi.h> - -#include "mach_apic.h" - -#include <linux/init.h> -#include <linux/smp.h> - -char visws_board_type = -1; -char visws_board_rev = -1; - -int is_visws_box(void) -{ - return visws_board_type >= 0; -} - -static int __init visws_time_init_quirk(void) -{ - printk(KERN_INFO "Starting Cobalt Timer system clock\n"); - - /* Set the countdown value */ - co_cpu_write(CO_CPU_TIMEVAL, CO_TIME_HZ/HZ); - - /* Start the timer */ - co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) | CO_CTRL_TIMERUN); - - /* Enable (unmask) the timer interrupt */ - co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) & ~CO_CTRL_TIMEMASK); - - /* - * Zero return means the generic timer setup code will set up - * the standard vector: - */ - return 0; -} - -static int __init visws_pre_intr_init_quirk(void) -{ - init_VISWS_APIC_irqs(); - - /* - * We dont want ISA irqs to be set up by the generic code: - */ - return 1; -} - -/* Quirk for machine specific memory setup. */ - -#define MB (1024 * 1024) - -unsigned long sgivwfb_mem_phys; -unsigned long sgivwfb_mem_size; -EXPORT_SYMBOL(sgivwfb_mem_phys); -EXPORT_SYMBOL(sgivwfb_mem_size); - -long long mem_size __initdata = 0; - -static char * __init visws_memory_setup_quirk(void) -{ - long long gfx_mem_size = 8 * MB; - - mem_size = boot_params.alt_mem_k; - - if (!mem_size) { - printk(KERN_WARNING "Bootloader didn't set memory size, upgrade it !\n"); - mem_size = 128 * MB; - } - - /* - * this hardcodes the graphics memory to 8 MB - * it really should be sized dynamically (or at least - * set as a boot param) - */ - if (!sgivwfb_mem_size) { - printk(KERN_WARNING "Defaulting to 8 MB framebuffer size\n"); - sgivwfb_mem_size = 8 * MB; - } - - /* - * Trim to nearest MB - */ - sgivwfb_mem_size &= ~((1 << 20) - 1); - sgivwfb_mem_phys = mem_size - gfx_mem_size; - - e820_add_region(0, LOWMEMSIZE(), E820_RAM); - e820_add_region(HIGH_MEMORY, mem_size - sgivwfb_mem_size - HIGH_MEMORY, E820_RAM); - e820_add_region(sgivwfb_mem_phys, sgivwfb_mem_size, E820_RESERVED); - - return "PROM"; -} - -static void visws_machine_emergency_restart(void) -{ - /* - * Visual Workstations restart after this - * register is poked on the PIIX4 - */ - outb(PIIX4_RESET_VAL, PIIX4_RESET_PORT); -} - -static void visws_machine_power_off(void) -{ - unsigned short pm_status; -/* extern unsigned int pci_bus0; */ - - while ((pm_status = inw(PMSTS_PORT)) & 0x100) - outw(pm_status, PMSTS_PORT); - - outw(PM_SUSPEND_ENABLE, PMCNTRL_PORT); - - mdelay(10); - -#define PCI_CONF1_ADDRESS(bus, devfn, reg) \ - (0x80000000 | (bus << 16) | (devfn << 8) | (reg & ~3)) - -/* outl(PCI_CONF1_ADDRESS(pci_bus0, SPECIAL_DEV, SPECIAL_REG), 0xCF8); */ - outl(PIIX_SPECIAL_STOP, 0xCFC); -} - -static int __init visws_get_smp_config_quirk(unsigned int early) -{ - /* - * Prevent MP-table parsing by the generic code: - */ - return 1; -} - -extern unsigned int __cpuinitdata maxcpus; - -/* - * The Visual Workstation is Intel MP compliant in the hardware - * sense, but it doesn't have a BIOS(-configuration table). - * No problem for Linux. - */ - -static void __init MP_processor_info (struct mpc_config_processor *m) -{ - int ver, logical_apicid; - physid_mask_t apic_cpus; - - if (!(m->mpc_cpuflag & CPU_ENABLED)) - return; - - logical_apicid = m->mpc_apicid; - printk(KERN_INFO "%sCPU #%d %u:%u APIC version %d\n", - m->mpc_cpuflag & CPU_BOOTPROCESSOR ? "Bootup " : "", - m->mpc_apicid, - (m->mpc_cpufeature & CPU_FAMILY_MASK) >> 8, - (m->mpc_cpufeature & CPU_MODEL_MASK) >> 4, - m->mpc_apicver); - - if (m->mpc_cpuflag & CPU_BOOTPROCESSOR) - boot_cpu_physical_apicid = m->mpc_apicid; - - ver = m->mpc_apicver; - if ((ver >= 0x14 && m->mpc_apicid >= 0xff) || m->mpc_apicid >= 0xf) { - printk(KERN_ERR "Processor #%d INVALID. (Max ID: %d).\n", - m->mpc_apicid, MAX_APICS); - return; - } - - apic_cpus = apicid_to_cpu_present(m->mpc_apicid); - physids_or(phys_cpu_present_map, phys_cpu_present_map, apic_cpus); - /* - * Validate version - */ - if (ver == 0x0) { - printk(KERN_ERR "BIOS bug, APIC version is 0 for CPU#%d! " - "fixing up to 0x10. (tell your hw vendor)\n", - m->mpc_apicid); - ver = 0x10; - } - apic_version[m->mpc_apicid] = ver; -} - -int __init visws_find_smp_config_quirk(unsigned int reserve) -{ - struct mpc_config_processor *mp = phys_to_virt(CO_CPU_TAB_PHYS); - unsigned short ncpus = readw(phys_to_virt(CO_CPU_NUM_PHYS)); - - if (ncpus > CO_CPU_MAX) { - printk(KERN_WARNING "find_visws_smp: got cpu count of %d at %p\n", - ncpus, mp); - - ncpus = CO_CPU_MAX; - } - - if (ncpus > maxcpus) - ncpus = maxcpus; - -#ifdef CONFIG_X86_LOCAL_APIC - smp_found_config = 1; -#endif - while (ncpus--) - MP_processor_info(mp++); - - mp_lapic_addr = APIC_DEFAULT_PHYS_BASE; - - return 1; -} - -extern int visws_trap_init_quirk(void); - -void __init visws_early_detect(void) -{ - int raw; - - visws_board_type = (char)(inb_p(PIIX_GPI_BD_REG) & PIIX_GPI_BD_REG) - >> PIIX_GPI_BD_SHIFT; - - if (visws_board_type < 0) - return; - - /* - * Install special quirks for timer, interrupt and memory setup: - */ - arch_time_init_quirk = visws_time_init_quirk; - arch_pre_intr_init_quirk = visws_pre_intr_init_quirk; - arch_memory_setup_quirk = visws_memory_setup_quirk; - - /* - * Fall back to generic behavior for traps: - */ - arch_intr_init_quirk = NULL; - arch_trap_init_quirk = visws_trap_init_quirk; - - /* - * Install reboot quirks: - */ - pm_power_off = visws_machine_power_off; - machine_ops.emergency_restart = visws_machine_emergency_restart; - - /* - * Do not use broadcast IPIs: - */ - no_broadcast = 0; - - /* - * Override generic MP-table parsing: - */ - mach_get_smp_config_quirk = visws_get_smp_config_quirk; - mach_find_smp_config_quirk = visws_find_smp_config_quirk; - - /* - * Get Board rev. - * First, we have to initialize the 307 part to allow us access - * to the GPIO registers. Let's map them at 0x0fc0 which is right - * after the PIIX4 PM section. - */ - outb_p(SIO_DEV_SEL, SIO_INDEX); - outb_p(SIO_GP_DEV, SIO_DATA); /* Talk to GPIO regs. */ - - outb_p(SIO_DEV_MSB, SIO_INDEX); - outb_p(SIO_GP_MSB, SIO_DATA); /* MSB of GPIO base address */ - - outb_p(SIO_DEV_LSB, SIO_INDEX); - outb_p(SIO_GP_LSB, SIO_DATA); /* LSB of GPIO base address */ - - outb_p(SIO_DEV_ENB, SIO_INDEX); - outb_p(1, SIO_DATA); /* Enable GPIO registers. */ - - /* - * Now, we have to map the power management section to write - * a bit which enables access to the GPIO registers. - * What lunatic came up with this shit? - */ - outb_p(SIO_DEV_SEL, SIO_INDEX); - outb_p(SIO_PM_DEV, SIO_DATA); /* Talk to GPIO regs. */ - - outb_p(SIO_DEV_MSB, SIO_INDEX); - outb_p(SIO_PM_MSB, SIO_DATA); /* MSB of PM base address */ - - outb_p(SIO_DEV_LSB, SIO_INDEX); - outb_p(SIO_PM_LSB, SIO_DATA); /* LSB of PM base address */ - - outb_p(SIO_DEV_ENB, SIO_INDEX); - outb_p(1, SIO_DATA); /* Enable PM registers. */ - - /* - * Now, write the PM register which enables the GPIO registers. - */ - outb_p(SIO_PM_FER2, SIO_PM_INDEX); - outb_p(SIO_PM_GP_EN, SIO_PM_DATA); - - /* - * Now, initialize the GPIO registers. - * We want them all to be inputs which is the - * power on default, so let's leave them alone. - * So, let's just read the board rev! - */ - raw = inb_p(SIO_GP_DATA1); - raw &= 0x7f; /* 7 bits of valid board revision ID. */ - - if (visws_board_type == VISWS_320) { - if (raw < 0x6) { - visws_board_rev = 4; - } else if (raw < 0xc) { - visws_board_rev = 5; - } else { - visws_board_rev = 6; - } - } else if (visws_board_type == VISWS_540) { - visws_board_rev = 2; - } else { - visws_board_rev = raw; - } - - printk(KERN_INFO "Silicon Graphics Visual Workstation %s (rev %d) detected\n", - (visws_board_type == VISWS_320 ? "320" : - (visws_board_type == VISWS_540 ? "540" : - "unknown")), visws_board_rev); -} diff --git a/arch/x86/mach-visws/traps.c b/arch/x86/mach-visws/traps.c deleted file mode 100644 index e5e6492c267..00000000000 --- a/arch/x86/mach-visws/traps.c +++ /dev/null @@ -1,71 +0,0 @@ -/* VISWS traps */ - -#include <linux/sched.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/pci_ids.h> - -#include <asm/io.h> -#include <asm/apic.h> -#include <asm/arch_hooks.h> -#include <asm/visws/cobalt.h> -#include <asm/visws/lithium.h> - - -#define A01234 (LI_INTA_0 | LI_INTA_1 | LI_INTA_2 | LI_INTA_3 | LI_INTA_4) -#define BCD (LI_INTB | LI_INTC | LI_INTD) -#define ALLDEVS (A01234 | BCD) - -static __init void lithium_init(void) -{ - set_fixmap(FIX_LI_PCIA, LI_PCI_A_PHYS); - set_fixmap(FIX_LI_PCIB, LI_PCI_B_PHYS); - - if ((li_pcia_read16(PCI_VENDOR_ID) != PCI_VENDOR_ID_SGI) || - (li_pcia_read16(PCI_DEVICE_ID) != PCI_DEVICE_ID_SGI_LITHIUM)) { - printk(KERN_EMERG "Lithium hostbridge %c not found\n", 'A'); -/* panic("This machine is not SGI Visual Workstation 320/540"); */ - } - - if ((li_pcib_read16(PCI_VENDOR_ID) != PCI_VENDOR_ID_SGI) || - (li_pcib_read16(PCI_DEVICE_ID) != PCI_DEVICE_ID_SGI_LITHIUM)) { - printk(KERN_EMERG "Lithium hostbridge %c not found\n", 'B'); -/* panic("This machine is not SGI Visual Workstation 320/540"); */ - } - - li_pcia_write16(LI_PCI_INTEN, ALLDEVS); - li_pcib_write16(LI_PCI_INTEN, ALLDEVS); -} - -static __init void cobalt_init(void) -{ - /* - * On normal SMP PC this is used only with SMP, but we have to - * use it and set it up here to start the Cobalt clock - */ - set_fixmap(FIX_APIC_BASE, APIC_DEFAULT_PHYS_BASE); - setup_local_APIC(); - printk(KERN_INFO "Local APIC Version %#x, ID %#x\n", - (unsigned int)apic_read(APIC_LVR), - (unsigned int)apic_read(APIC_ID)); - - set_fixmap(FIX_CO_CPU, CO_CPU_PHYS); - set_fixmap(FIX_CO_APIC, CO_APIC_PHYS); - printk(KERN_INFO "Cobalt Revision %#lx, APIC ID %#lx\n", - co_cpu_read(CO_CPU_REV), co_apic_read(CO_APIC_ID)); - - /* Enable Cobalt APIC being careful to NOT change the ID! */ - co_apic_write(CO_APIC_ID, co_apic_read(CO_APIC_ID) | CO_APIC_ENABLE); - - printk(KERN_INFO "Cobalt APIC enabled: ID reg %#lx\n", - co_apic_read(CO_APIC_ID)); -} - -int __init visws_trap_init_quirk(void) -{ - lithium_init(); - cobalt_init(); - - return 1; -} diff --git a/arch/x86/mach-visws/visws_apic.c b/arch/x86/mach-visws/visws_apic.c deleted file mode 100644 index 6c02c8d0993..00000000000 --- a/arch/x86/mach-visws/visws_apic.c +++ /dev/null @@ -1,295 +0,0 @@ -/* - * Copyright (C) 1999 Bent Hagemark, Ingo Molnar - * - * SGI Visual Workstation interrupt controller - * - * The Cobalt system ASIC in the Visual Workstation contains a "Cobalt" APIC - * which serves as the main interrupt controller in the system. Non-legacy - * hardware in the system uses this controller directly. Legacy devices - * are connected to the PIIX4 which in turn has its 8259(s) connected to - * a of the Cobalt APIC entry. - * - * 09/02/2000 - Updated for 2.4 by jbarnes@sgi.com - * - * 25/11/2002 - Updated for 2.5 by Andrey Panin <pazke@orbita1.ru> - */ - -#include <linux/kernel_stat.h> -#include <linux/interrupt.h> -#include <linux/init.h> - -#include <asm/io.h> -#include <asm/apic.h> -#include <asm/i8259.h> -#include <asm/irq_vectors.h> -#include <asm/visws/cobalt.h> - -static DEFINE_SPINLOCK(cobalt_lock); - -/* - * Set the given Cobalt APIC Redirection Table entry to point - * to the given IDT vector/index. - */ -static inline void co_apic_set(int entry, int irq) -{ - co_apic_write(CO_APIC_LO(entry), CO_APIC_LEVEL | (irq + FIRST_EXTERNAL_VECTOR)); - co_apic_write(CO_APIC_HI(entry), 0); -} - -/* - * Cobalt (IO)-APIC functions to handle PCI devices. - */ -static inline int co_apic_ide0_hack(void) -{ - extern char visws_board_type; - extern char visws_board_rev; - - if (visws_board_type == VISWS_320 && visws_board_rev == 5) - return 5; - return CO_APIC_IDE0; -} - -static int is_co_apic(unsigned int irq) -{ - if (IS_CO_APIC(irq)) - return CO_APIC(irq); - - switch (irq) { - case 0: return CO_APIC_CPU; - case CO_IRQ_IDE0: return co_apic_ide0_hack(); - case CO_IRQ_IDE1: return CO_APIC_IDE1; - default: return -1; - } -} - - -/* - * This is the SGI Cobalt (IO-)APIC: - */ - -static void enable_cobalt_irq(unsigned int irq) -{ - co_apic_set(is_co_apic(irq), irq); -} - -static void disable_cobalt_irq(unsigned int irq) -{ - int entry = is_co_apic(irq); - - co_apic_write(CO_APIC_LO(entry), CO_APIC_MASK); - co_apic_read(CO_APIC_LO(entry)); -} - -/* - * "irq" really just serves to identify the device. Here is where we - * map this to the Cobalt APIC entry where it's physically wired. - * This is called via request_irq -> setup_irq -> irq_desc->startup() - */ -static unsigned int startup_cobalt_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - if ((irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS | IRQ_WAITING))) - irq_desc[irq].status &= ~(IRQ_DISABLED | IRQ_INPROGRESS | IRQ_WAITING); - enable_cobalt_irq(irq); - spin_unlock_irqrestore(&cobalt_lock, flags); - return 0; -} - -static void ack_cobalt_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - disable_cobalt_irq(irq); - apic_write(APIC_EOI, APIC_EIO_ACK); - spin_unlock_irqrestore(&cobalt_lock, flags); -} - -static void end_cobalt_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) - enable_cobalt_irq(irq); - spin_unlock_irqrestore(&cobalt_lock, flags); -} - -static struct irq_chip cobalt_irq_type = { - .typename = "Cobalt-APIC", - .startup = startup_cobalt_irq, - .shutdown = disable_cobalt_irq, - .enable = enable_cobalt_irq, - .disable = disable_cobalt_irq, - .ack = ack_cobalt_irq, - .end = end_cobalt_irq, -}; - - -/* - * This is the PIIX4-based 8259 that is wired up indirectly to Cobalt - * -- not the manner expected by the code in i8259.c. - * - * there is a 'master' physical interrupt source that gets sent to - * the CPU. But in the chipset there are various 'virtual' interrupts - * waiting to be handled. We represent this to Linux through a 'master' - * interrupt controller type, and through a special virtual interrupt- - * controller. Device drivers only see the virtual interrupt sources. - */ -static unsigned int startup_piix4_master_irq(unsigned int irq) -{ - init_8259A(0); - - return startup_cobalt_irq(irq); -} - -static void end_piix4_master_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - enable_cobalt_irq(irq); - spin_unlock_irqrestore(&cobalt_lock, flags); -} - -static struct irq_chip piix4_master_irq_type = { - .typename = "PIIX4-master", - .startup = startup_piix4_master_irq, - .ack = ack_cobalt_irq, - .end = end_piix4_master_irq, -}; - - -static struct irq_chip piix4_virtual_irq_type = { - .typename = "PIIX4-virtual", - .shutdown = disable_8259A_irq, - .enable = enable_8259A_irq, - .disable = disable_8259A_irq, -}; - - -/* - * PIIX4-8259 master/virtual functions to handle interrupt requests - * from legacy devices: floppy, parallel, serial, rtc. - * - * None of these get Cobalt APIC entries, neither do they have IDT - * entries. These interrupts are purely virtual and distributed from - * the 'master' interrupt source: CO_IRQ_8259. - * - * When the 8259 interrupts its handler figures out which of these - * devices is interrupting and dispatches to its handler. - * - * CAREFUL: devices see the 'virtual' interrupt only. Thus disable/ - * enable_irq gets the right irq. This 'master' irq is never directly - * manipulated by any driver. - */ -static irqreturn_t piix4_master_intr(int irq, void *dev_id) -{ - int realirq; - irq_desc_t *desc; - unsigned long flags; - - spin_lock_irqsave(&i8259A_lock, flags); - - /* Find out what's interrupting in the PIIX4 master 8259 */ - outb(0x0c, 0x20); /* OCW3 Poll command */ - realirq = inb(0x20); - - /* - * Bit 7 == 0 means invalid/spurious - */ - if (unlikely(!(realirq & 0x80))) - goto out_unlock; - - realirq &= 7; - - if (unlikely(realirq == 2)) { - outb(0x0c, 0xa0); - realirq = inb(0xa0); - - if (unlikely(!(realirq & 0x80))) - goto out_unlock; - - realirq = (realirq & 7) + 8; - } - - /* mask and ack interrupt */ - cached_irq_mask |= 1 << realirq; - if (unlikely(realirq > 7)) { - inb(0xa1); - outb(cached_slave_mask, 0xa1); - outb(0x60 + (realirq & 7), 0xa0); - outb(0x60 + 2, 0x20); - } else { - inb(0x21); - outb(cached_master_mask, 0x21); - outb(0x60 + realirq, 0x20); - } - - spin_unlock_irqrestore(&i8259A_lock, flags); - - desc = irq_desc + realirq; - - /* - * handle this 'virtual interrupt' as a Cobalt one now. - */ - kstat_cpu(smp_processor_id()).irqs[realirq]++; - - if (likely(desc->action != NULL)) - handle_IRQ_event(realirq, desc->action); - - if (!(desc->status & IRQ_DISABLED)) - enable_8259A_irq(realirq); - - return IRQ_HANDLED; - -out_unlock: - spin_unlock_irqrestore(&i8259A_lock, flags); - return IRQ_NONE; -} - -static struct irqaction master_action = { - .handler = piix4_master_intr, - .name = "PIIX4-8259", -}; - -static struct irqaction cascade_action = { - .handler = no_action, - .name = "cascade", -}; - - -void init_VISWS_APIC_irqs(void) -{ - int i; - - for (i = 0; i < CO_IRQ_APIC0 + CO_APIC_LAST + 1; i++) { - irq_desc[i].status = IRQ_DISABLED; - irq_desc[i].action = 0; - irq_desc[i].depth = 1; - - if (i == 0) { - irq_desc[i].chip = &cobalt_irq_type; - } - else if (i == CO_IRQ_IDE0) { - irq_desc[i].chip = &cobalt_irq_type; - } - else if (i == CO_IRQ_IDE1) { - irq_desc[i].chip = &cobalt_irq_type; - } - else if (i == CO_IRQ_8259) { - irq_desc[i].chip = &piix4_master_irq_type; - } - else if (i < CO_IRQ_APIC0) { - irq_desc[i].chip = &piix4_virtual_irq_type; - } - else if (IS_CO_APIC(i)) { - irq_desc[i].chip = &cobalt_irq_type; - } - } - - setup_irq(CO_IRQ_8259, &master_action); - setup_irq(2, &cascade_action); -} |