diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/avr32/Kconfig | 4 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/Kconfig | 53 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1002.c | 30 |
3 files changed, 80 insertions, 7 deletions
diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index 8f37a14e637..d12346aaa88 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -113,6 +113,10 @@ config BOARD_ATNGW100 bool "ATNGW100 Network Gateway" endchoice +if BOARD_ATSTK1000 +source "arch/avr32/boards/atstk1000/Kconfig" +endif + choice prompt "Boot loader type" default LOADER_U_BOOT diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig new file mode 100644 index 00000000000..71bc7d364fb --- /dev/null +++ b/arch/avr32/boards/atstk1000/Kconfig @@ -0,0 +1,53 @@ +# STK1000 customization + +if BOARD_ATSTK1002 + +config BOARD_ATSTK1002_CUSTOM + bool "Non-default STK-1002 jumper settings" + help + You will normally leave the jumpers on the CPU card at their + default settings. If you need to use certain peripherals, + you will need to change some of those jumpers. + +if BOARD_ATSTK1002_CUSTOM + +config BOARD_ATSTK1002_SW1_CUSTOM + bool "SW1: use SSC1 (not SPI0)" + help + This also prevents using the external DAC as an audio interface, + and means you can't initialize the on-board QVGA display. + +config BOARD_ATSTK1002_SW2_CUSTOM + bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)" + help + If you change this you'll want an updated boot loader putting + the console on UART-C not UART-A. + +config BOARD_ATSTK1002_SW3_CUSTOM + bool "SW3: use TIMER1 (not SSC0 and GCLK)" + help + This also prevents using the external DAC as an audio interface. + +config BOARD_ATSTK1002_SW4_CUSTOM + bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)" + help + To use the camera interface you'll need a custom card (on the + PCI-format connector) connect a video sensor. + +config BOARD_ATSTK1002_SW5_CUSTOM + bool "SW5: use MACB1 (not LCDC)" + +config BOARD_ATSTK1002_SW6_CUSTOM + bool "SW6: more GPIOs (not MACB0)" + +endif # custom + +config BOARD_ATSTK1002_SPI1 + bool "Configure SPI1 controller" + depends on !BOARD_ATSTK1002_SW4_CUSTOM + help + All the signals for the second SPI controller are available on + GPIO lines and accessed through the J1 jumper block. Say "y" + here to configure that SPI controller. + +endif # stk 1002 diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index e253e86a1a3..6b2187f3503 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -27,7 +27,6 @@ #include "atstk1000.h" -#define SW2_DEFAULT /* MMCI and UART_A available */ struct eth_addr { u8 addr[6]; @@ -36,6 +35,7 @@ struct eth_addr { static struct eth_addr __initdata hw_addr[2]; static struct eth_platform_data __initdata eth_data[2]; +#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM static struct spi_board_info spi0_board_info[] __initdata = { { /* QVGA display */ @@ -45,6 +45,13 @@ static struct spi_board_info spi0_board_info[] __initdata = { .mode = SPI_MODE_3, }, }; +#endif + +#ifdef CONFIG_BOARD_ATSTK1002_SPI1 +static struct spi_board_info spi1_board_info[] __initdata = { { + /* patch in custom entries here */ +} }; +#endif /* * The next two functions should go away as the boot loader is @@ -103,10 +110,10 @@ static void __init set_hw_addr(struct platform_device *pdev) void __init setup_board(void) { -#ifdef SW2_DEFAULT - at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */ -#else +#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */ +#else + at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */ #endif /* USART 2/unused: expansion connector */ at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */ @@ -140,18 +147,27 @@ static int __init atstk1002_init(void) at32_add_system_devices(); -#ifdef SW2_DEFAULT - at32_add_device_usart(0); -#else +#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM at32_add_device_usart(1); +#else + at32_add_device_usart(0); #endif at32_add_device_usart(2); set_hw_addr(at32_add_device_eth(0, ð_data[0])); +#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); +#endif +#ifdef CONFIG_BOARD_ATSTK1002_SPI1 + at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); +#endif +#ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM + set_hw_addr(at32_add_device_eth(1, ð_data[1])); +#else at32_add_device_lcdc(0, &atstk1000_lcdc_data, fbmem_start, fbmem_size); +#endif return 0; } |