diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/m68k/Kconfig | 195 | ||||
| -rw-r--r-- | arch/m68k/Kconfig.bus | 55 | ||||
| -rw-r--r-- | arch/m68k/Kconfig.cpu | 429 | ||||
| -rw-r--r-- | arch/m68k/Kconfig.devices | 171 | ||||
| -rw-r--r-- | arch/m68k/Kconfig.machine (renamed from arch/m68k/Kconfig.nommu) | 543 | ||||
| -rw-r--r-- | arch/m68k/Kconfig.mmu | 411 |
6 files changed, 888 insertions, 916 deletions
diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig index 9e8ee9d2b8c..6c28582fb98 100644 --- a/arch/m68k/Kconfig +++ b/arch/m68k/Kconfig @@ -21,6 +21,15 @@ config ARCH_HAS_ILOG2_U32 config ARCH_HAS_ILOG2_U64 bool +config GENERIC_CLOCKEVENTS + bool + +config GENERIC_CMOS_UPDATE + def_bool !MMU + +config GENERIC_GPIO + bool + config GENERIC_HWEIGHT bool default y @@ -29,10 +38,16 @@ config GENERIC_CALIBRATE_DELAY bool default y +config GENERIC_IOMAP + def_bool MMU + config TIME_LOW_RES bool default y +config ARCH_USES_GETTIMEOFFSET + def_bool MMU + config NO_IOPORT def_bool y @@ -62,13 +77,31 @@ config MMU Select if you want MMU-based virtualised addressing space support by paged memory management. If unsure, say 'Y'. -menu "Platform dependent setup" +config MMU_MOTOROLA + bool + +config MMU_SUN3 + bool + depends on MMU && !MMU_MOTOROLA + +menu "Platform setup" + +source arch/m68k/Kconfig.cpu + +source arch/m68k/Kconfig.machine + +source arch/m68k/Kconfig.bus + +endmenu + +menu "Kernel Features" -if MMU -source arch/m68k/Kconfig.mmu +if COLDFIRE +source "kernel/Kconfig.preempt" endif -if !MMU -source arch/m68k/Kconfig.nommu + +if !MMU || COLDFIRE +source "kernel/time/Kconfig" endif source "mm/Kconfig" @@ -85,9 +118,9 @@ if !MMU menu "Power management options" config PM - bool "Power Management support" - help - Support processor power management modes + bool "Power Management support" + help + Support processor power management modes endmenu endif @@ -96,151 +129,7 @@ source "net/Kconfig" source "drivers/Kconfig" -if MMU - -menu "Character devices" - -config ATARI_MFPSER - tristate "Atari MFP serial support" - depends on ATARI - ---help--- - If you like to use the MFP serial ports ("Modem1", "Serial1") under - Linux, say Y. The driver equally supports all kinds of MFP serial - ports and automatically detects whether Serial1 is available. - - To compile this driver as a module, choose M here. - - Note for Falcon users: You also have an MFP port, it's just not - wired to the outside... But you could use the port under Linux. - -config ATARI_MIDI - tristate "Atari MIDI serial support" - depends on ATARI - help - If you want to use your Atari's MIDI port in Linux, say Y. - - To compile this driver as a module, choose M here. - -config ATARI_DSP56K - tristate "Atari DSP56k support (EXPERIMENTAL)" - depends on ATARI && EXPERIMENTAL - help - If you want to be able to use the DSP56001 in Falcons, say Y. This - driver is still experimental, and if you don't know what it is, or - if you don't have this processor, just say N. - - To compile this driver as a module, choose M here. - -config AMIGA_BUILTIN_SERIAL - tristate "Amiga builtin serial support" - depends on AMIGA - help - If you want to use your Amiga's built-in serial port in Linux, - answer Y. - - To compile this driver as a module, choose M here. - -config MULTIFACE_III_TTY - tristate "Multiface Card III serial support" - depends on AMIGA - help - If you want to use a Multiface III card's serial port in Linux, - answer Y. - - To compile this driver as a module, choose M here. - -config GVPIOEXT - tristate "GVP IO-Extender support" - depends on PARPORT=n && ZORRO - help - If you want to use a GVP IO-Extender serial card in Linux, say Y. - Otherwise, say N. - -config GVPIOEXT_LP - tristate "GVP IO-Extender parallel printer support" - depends on GVPIOEXT - help - Say Y to enable driving a printer from the parallel port on your - GVP IO-Extender card, N otherwise. - -config GVPIOEXT_PLIP - tristate "GVP IO-Extender PLIP support" - depends on GVPIOEXT - help - Say Y to enable doing IP over the parallel port on your GVP - IO-Extender card, N otherwise. - -config MAC_HID - bool - depends on INPUT_ADBHID - default y - -config HPDCA - tristate "HP DCA serial support" - depends on DIO && SERIAL_8250 - help - If you want to use the internal "DCA" serial ports on an HP300 - machine, say Y here. - -config HPAPCI - tristate "HP APCI serial support" - depends on HP300 && SERIAL_8250 && EXPERIMENTAL - help - If you want to use the internal "APCI" serial ports on an HP400 - machine, say Y here. - -config MVME147_SCC - bool "SCC support for MVME147 serial ports" - depends on MVME147 && BROKEN - help - This is the driver for the serial ports on the Motorola MVME147 - boards. Everyone using one of these boards should say Y here. - -config MVME162_SCC - bool "SCC support for MVME162 serial ports" - depends on MVME16x && BROKEN - help - This is the driver for the serial ports on the Motorola MVME162 and - 172 boards. Everyone using one of these boards should say Y here. - -config BVME6000_SCC - bool "SCC support for BVME6000 serial ports" - depends on BVME6000 && BROKEN - help - This is the driver for the serial ports on the BVME4000 and BVME6000 - boards from BVM Ltd. Everyone using one of these boards should say - Y here. - -config DN_SERIAL - bool "Support for DN serial port (dummy)" - depends on APOLLO - -config SERIAL_CONSOLE - bool "Support for serial port console" - depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL) - ---help--- - If you say Y here, it will be possible to use a serial port as the - system console (the system console is the device which receives all - kernel messages and warnings and which allows logins in single user - mode). This could be useful if some terminal or printer is connected - to that serial port. - - Even if you say Y here, the currently visible virtual console - (/dev/tty0) will still be used as the system console by default, but - you can alter that using a kernel command line option such as - "console=ttyS1". (Try "man bootparam" or see the documentation of - your boot loader (lilo or loadlin) about how to pass options to the - kernel at boot time.) - - If you don't have a VGA card installed and you say Y here, the - kernel will automatically use the first serial line, /dev/ttyS0, as - system console. - - If unsure, say N. - -endmenu - -endif +source "arch/m68k/Kconfig.devices" source "fs/Kconfig" diff --git a/arch/m68k/Kconfig.bus b/arch/m68k/Kconfig.bus new file mode 100644 index 00000000000..8294f0c1785 --- /dev/null +++ b/arch/m68k/Kconfig.bus @@ -0,0 +1,55 @@ +if MMU + +comment "Bus Support" + +config NUBUS + bool + depends on MAC + default y + +config ZORRO + bool "Amiga Zorro (AutoConfig) bus support" + depends on AMIGA + help + This enables support for the Zorro bus in the Amiga. If you have + expansion cards in your Amiga that conform to the Amiga + AutoConfig(tm) specification, say Y, otherwise N. Note that even + expansion cards that do not fit in the Zorro slots but fit in e.g. + the CPU slot may fall in this category, so you have to say Y to let + Linux use these. + +config AMIGA_PCMCIA + bool "Amiga 1200/600 PCMCIA support (EXPERIMENTAL)" + depends on AMIGA && EXPERIMENTAL + help + Include support in the kernel for pcmcia on Amiga 1200 and Amiga + 600. If you intend to use pcmcia cards say Y; otherwise say N. + +config ISA + bool + depends on Q40 || AMIGA_PCMCIA + default y + help + Find out whether you have ISA slots on your motherboard. ISA is the + name of a bus system, i.e. the way the CPU talks to the other stuff + inside your box. Other bus systems are PCI, EISA, MicroChannel + (MCA) or VESA. ISA is an older system, now being displaced by PCI; + newer boards don't support it. If you have ISA, say Y, otherwise N. + +config GENERIC_ISA_DMA + def_bool ISA + +source "drivers/pci/Kconfig" + +source "drivers/zorro/Kconfig" + +endif + +if !MMU + +config ISA_DMA_API + def_bool !M5272 + +source "drivers/pcmcia/Kconfig" + +endif diff --git a/arch/m68k/Kconfig.cpu b/arch/m68k/Kconfig.cpu new file mode 100644 index 00000000000..e632b2d1210 --- /dev/null +++ b/arch/m68k/Kconfig.cpu @@ -0,0 +1,429 @@ +comment "Processor Type" + +config M68000 + bool + select CPU_HAS_NO_BITFIELDS + help + The Freescale (was Motorola) 68000 CPU is the first generation of + the well known M68K family of processors. The CPU core as well as + being available as a stand alone CPU was also used in many + System-On-Chip devices (eg 68328, 68302, etc). It does not contain + a paging MMU. + +config MCPU32 + bool + select CPU_HAS_NO_BITFIELDS + help + The Freescale (was then Motorola) CPU32 is a CPU core that is + based on the 68020 processor. For the most part it is used in + System-On-Chip parts, and does not contain a paging MMU. + +config COLDFIRE + bool + select GENERIC_GPIO + select ARCH_REQUIRE_GPIOLIB + select CPU_HAS_NO_BITFIELDS + help + The Freescale ColdFire family of processors is a modern derivitive + of the 68000 processor family. They are mainly targeted at embedded + applications, and are all System-On-Chip (SOC) devices, as opposed + to stand alone CPUs. They implement a subset of the original 68000 + processor instruction set. + +config M68020 + bool "68020 support" + depends on MMU + help + If you anticipate running this kernel on a computer with a MC68020 + processor, say Y. Otherwise, say N. Note that the 68020 requires a + 68851 MMU (Memory Management Unit) to run Linux/m68k, except on the + Sun 3, which provides its own version. + +config M68030 + bool "68030 support" + depends on MMU && !MMU_SUN3 + help + If you anticipate running this kernel on a computer with a MC68030 + processor, say Y. Otherwise, say N. Note that a MC68EC030 will not + work, as it does not include an MMU (Memory Management Unit). + +config M68040 + bool "68040 support" + depends on MMU && !MMU_SUN3 + help + If you anticipate running this kernel on a computer with a MC68LC040 + or MC68040 processor, say Y. Otherwise, say N. Note that an + MC68EC040 will not work, as it does not include an MMU (Memory + Management Unit). + +config M68060 + bool "68060 support" + depends on MMU && !MMU_SUN3 + help + If you anticipate running this kernel on a computer with a MC68060 + processor, say Y. Otherwise, say N. + +config M68328 + bool "MC68328" + depends on !MMU + select M68000 + help + Motorola 68328 processor support. + +config M68EZ328 + bool "MC68EZ328" + depends on !MMU + select M68000 + help + Motorola 68EX328 processor support. + +config M68VZ328 + bool "MC68VZ328" + depends on !MMU + select M68000 + help + Motorola 68VZ328 processor support. + +config M68360 + bool "MC68360" + depends on !MMU + select MCPU32 + help + Motorola 68360 processor support. + +config M5206 + bool "MCF5206" + depends on !MMU + select COLDFIRE + select COLDFIRE_SW_A7 + select HAVE_MBAR + help + Motorola ColdFire 5206 processor support. + +config M5206e + bool "MCF5206e" + depends on !MMU + select COLDFIRE + select COLDFIRE_SW_A7 + select HAVE_MBAR + help + Motorola ColdFire 5206e processor support. + +config M520x + bool "MCF520x" + depends on !MMU + select COLDFIRE + select GENERIC_CLOCKEVENTS + select HAVE_CACHE_SPLIT + help + Freescale Coldfire 5207/5208 processor support. + +config M523x + bool "MCF523x" + depends on !MMU + select COLDFIRE + select GENERIC_CLOCKEVENTS + select HAVE_CACHE_SPLIT + select HAVE_IPSBAR + help + Freescale Coldfire 5230/1/2/4/5 processor support + +config M5249 + bool "MCF5249" + depends on !MMU + select COLDFIRE + select COLDFIRE_SW_A7 + select HAVE_MBAR + help + Motorola ColdFire 5249 processor support. + +config M527x + bool + +config M5271 + bool "MCF5271" + depends on !MMU + select COLDFIRE + select M527x + select HAVE_CACHE_SPLIT + select HAVE_IPSBAR + select GENERIC_CLOCKEVENTS + help + Freescale (Motorola) ColdFire 5270/5271 processor support. + +config M5272 + bool "MCF5272" + depends on !MMU + select COLDFIRE + select COLDFIRE_SW_A7 + select HAVE_MBAR + help + Motorola ColdFire 5272 processor support. + +config M5275 + bool "MCF5275" + depends on !MMU + select COLDFIRE + select M527x + select HAVE_CACHE_SPLIT + select HAVE_IPSBAR + select GENERIC_CLOCKEVENTS + help + Freescale (Motorola) ColdFire 5274/5275 processor support. + +config M528x + bool "MCF528x" + depends on !MMU + select COLDFIRE + select GENERIC_CLOCKEVENTS + select HAVE_CACHE_SPLIT + select HAVE_IPSBAR + help + Motorola ColdFire 5280/5282 processor support. + +config M5307 + bool "MCF5307" + depends on !MMU + select COLDFIRE + select COLDFIRE_SW_A7 + select HAVE_CACHE_CB + select HAVE_MBAR + help + Motorola ColdFire 5307 processor support. + +config M532x + bool "MCF532x" + depends on !MMU + select COLDFIRE + select HAVE_CACHE_CB + help + Freescale (Motorola) ColdFire 532x processor support. + +config M5407 + bool "MCF5407" + depends on !MMU + select COLDFIRE + select COLDFIRE_SW_A7 + select HAVE_CACHE_CB + select HAVE_MBAR + help + Motorola ColdFire 5407 processor support. + +config M54xx + bool + +config M547x + bool "MCF547x" + depends on !MMU + select COLDFIRE + select M54xx + select HAVE_CACHE_CB + select HAVE_MBAR + help + Freescale ColdFire 5470/5471/5472/5473/5474/5475 processor support. + +config M548x + bool "MCF548x" + depends on !MMU + select COLDFIRE + select M54xx + select HAVE_CACHE_CB + select HAVE_MBAR + help + Freescale ColdFire 5480/5481/5482/5483/5484/5485 processor support. + + +comment "Processor Specific Options" + +config M68KFPU_EMU + bool "Math emulation support (EXPERIMENTAL)" + depends on MMU + depends on EXPERIMENTAL + help + At some point in the future, this will cause floating-point math + instructions to be emulated by the kernel on machines that lack a + floating-point math coprocessor. Thrill-seekers and chronically + sleep-deprived psychotic hacker types can say Y now, everyone else + should probably wait a while. + +config M68KFPU_EMU_EXTRAPREC + bool "Math emulation extra precision" + depends on M68KFPU_EMU + help + The fpu uses normally a few bit more during calculations for + correct rounding, the emulator can (often) do the same but this + extra calculation can cost quite some time, so you can disable + it here. The emulator will then "only" calculate with a 64 bit + mantissa and round slightly incorrect, what is more than enough + for normal usage. + +config M68KFPU_EMU_ONLY + bool "Math emulation only kernel" + depends on M68KFPU_EMU + help + This option prevents any floating-point instructions from being + compiled into the kernel, thereby the kernel doesn't save any + floating point context anymore during task switches, so this + kernel will only be usable on machines without a floating-point + math coprocessor. This makes the kernel a bit faster as no tests + needs to be executed whether a floating-point instruction in the + kernel should be executed or not. + +config ADVANCED + bool "Advanced configuration options" + depends on MMU + ---help--- + This gives you access to some advanced options for the CPU. The + defaults should be fine for most users, but these options may make + it possible for you to improve performance somewhat if you know what + you are doing. + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about these options. + + Most users should say N to this question. + +config RMW_INSNS + bool "Use read-modify-write instructions" + depends on ADVANCED + ---help--- + This allows to use certain instructions that work with indivisible + read-modify-write bus cycles. While this is faster than the + workaround of disabling interrupts, it can conflict with DMA + ( = direct memory access) on many Amiga systems, and it is also said + to destabilize other machines. It is very likely that this will + cause serious problems on any Amiga or Atari Medusa if set. The only + configuration where it should work are 68030-based Ataris, where it + apparently improves performance. But you've been warned! Unless you + really know what you are doing, say N. Try Y only if you're quite + adventurous. + +config SINGLE_MEMORY_CHUNK + bool "Use one physical chunk of memory only" if ADVANCED && !SUN3 + depends on MMU + default y if SUN3 + select NEED_MULTIPLE_NODES + help + Ignore all but the first contiguous chunk of physical memory for VM + purposes. This will save a few bytes kernel size and may speed up + some operations. Say N if not sure. + +config ARCH_DISCONTIGMEM_ENABLE + def_bool MMU && !SINGLE_MEMORY_CHUNK + +config 060_WRITETHROUGH + bool "Use write-through caching for 68060 supervisor accesses" + depends on ADVANCED && M68060 + ---help--- + The 68060 generally uses copyback caching of recently accessed data. + Copyback caching means that memory writes will be held in an on-chip + cache and only written back to memory some time later. Saying Y + here will force supervisor (kernel) accesses to use writethrough + caching. Writethrough caching means that data is written to memory + straight away, so that cache and memory data always agree. + Writethrough caching is less efficient, but is needed for some + drivers on 68060 based systems where the 68060 bus snooping signal + is hardwired on. The 53c710 SCSI driver is known to suffer from + this problem. + +config M68K_L2_CACHE + bool + depends on MAC + default y + +config NODES_SHIFT + int + default "3" + depends on !SINGLE_MEMORY_CHUNK + +config FPU + bool + +config COLDFIRE_SW_A7 + bool + +config HAVE_CACHE_SPLIT + bool + +config HAVE_CACHE_CB + bool + +config HAVE_MBAR + bool + +config HAVE_IPSBAR + bool + +config CLOCK_SET + bool "Enable setting the CPU clock frequency" + depends on COLDFIRE + default n + help + On some CPU's you do not need to know what the core CPU clock + frequency is. On these you can disable clock setting. On some + traditional 68K parts, and on all ColdFire parts you need to set + the appropriate CPU clock frequency. On these devices many of the + onboard peripherals derive their timing from the master CPU clock + frequency. + +config CLOCK_FREQ + int "Set the core clock frequency" + default "66666666" + depends on CLOCK_SET + help + Define the CPU clock frequency in use. This is the core clock + frequency, it may or may not be the same as the external clock + crystal fitted to your board. Some processors have an internal + PLL and can have their frequency programmed at run time, others + use internal dividers. In general the kernel won't setup a PLL + if it is fitted (there are some exceptions). This value will be + specific to the exact CPU that you are using. + +config OLDMASK + bool "Old mask 5307 (1H55J) silicon" + depends on M5307 + help + Build support for the older revision ColdFire 5307 silicon. + Specifically this is the 1H55J mask revision. + +if HAVE_CACHE_SPLIT +choice + prompt "Split Cache Configuration" + default CACHE_I + +config CACHE_I + bool "Instruction" + help + Use all of the ColdFire CPU cache memory as an instruction cache. + +config CACHE_D + bool "Data" + help + Use all of the ColdFire CPU cache memory as a data cache. + +config CACHE_BOTH + bool "Both" + help + Split the ColdFire CPU cache, and use half as an instruction cache + and half as a data cache. +endchoice +endif + +if HAVE_CACHE_CB +choice + prompt "Data cache mode" + default CACHE_WRITETHRU + +config CACHE_WRITETHRU + bool "Write-through" + help + The ColdFire CPU cache is set into Write-through mode. + +config CACHE_COPYBACK + bool "Copy-back" + help + The ColdFire CPU cache is set into Copy-back mode. +endchoice +endif + diff --git a/arch/m68k/Kconfig.devices b/arch/m68k/Kconfig.devices new file mode 100644 index 00000000000..d964dc4c2ce --- /dev/null +++ b/arch/m68k/Kconfig.devices @@ -0,0 +1,171 @@ +if MMU + +config ARCH_MAY_HAVE_PC_FDC + bool + depends on BROKEN && (Q40 || SUN3X) + default y + +menu "Platform devices" + +config HEARTBEAT + bool "Use power LED as a heartbeat" if AMIGA || APOLLO || ATARI || MAC ||Q40 + default y if !AMIGA && !APOLLO && !ATARI && !MAC && !Q40 && HP300 + help + Use the power-on LED on your machine as a load meter. The exact + behavior is platform-dependent, but normally the flash frequency is + a hyperbolic function of the 5-minute load average. + +# We have a dedicated heartbeat LED. :-) +config PROC_HARDWARE + bool "/proc/hardware support" + help + Say Y here to support the /proc/hardware file, which gives you + access to information about the machine you're running on, + including the model, CPU, MMU, clock speed, BogoMIPS rating, + and memory size. + +endmenu + +menu "Character devices" + +config ATARI_MFPSER + tristate "Atari MFP serial support" + depends on ATARI + ---help--- + If you like to use the MFP serial ports ("Modem1", "Serial1") under + Linux, say Y. The driver equally supports all kinds of MFP serial + ports and automatically detects whether Serial1 is available. + + To compile this driver as a module, choose M here. + + Note for Falcon users: You also have an MFP port, it's just not + wired to the outside... But you could use the port under Linux. + +config ATARI_MIDI + tristate "Atari MIDI serial support" + depends on ATARI + help + If you want to use your Atari's MIDI port in Linux, say Y. + + To compile this driver as a module, choose M here. + +config ATARI_DSP56K + tristate "Atari DSP56k support (EXPERIMENTAL)" + depends on ATARI && EXPERIMENTAL + help + If you want to be able to use the DSP56001 in Falcons, say Y. This + driver is still experimental, and if you don't know what it is, or + if you don't have this processor, just say N. + + To compile this driver as a module, choose M here. + +config AMIGA_BUILTIN_SERIAL + tristate "Amiga builtin serial support" + depends on AMIGA + help + If you want to use your Amiga's built-in serial port in Linux, + answer Y. + + To compile this driver as a module, choose M here. + +config MULTIFACE_III_TTY + tristate "Multiface Card III serial support" + depends on AMIGA + help + If you want to use a Multiface III card's serial port in Linux, + answer Y. + + To compile this driver as a module, choose M here. + +config GVPIOEXT + tristate "GVP IO-Extender support" + depends on PARPORT=n && ZORRO + help + If you want to use a GVP IO-Extender serial card in Linux, say Y. + Otherwise, say N. + +config GVPIOEXT_LP + tristate "GVP IO-Extender parallel printer support" + depends on GVPIOEXT + help + Say Y to enable driving a printer from the parallel port on your + GVP IO-Extender card, N otherwise. + +config GVPIOEXT_PLIP + tristate "GVP IO-Extender PLIP support" + depends on GVPIOEXT + help + Say Y to enable doing IP over the parallel port on your GVP + IO-Extender card, N otherwise. + +config MAC_HID + bool + depends on INPUT_ADBHID + default y + +config HPDCA + tristate "HP DCA serial support" + depends on DIO && SERIAL_8250 + help + If you want to use the internal "DCA" serial ports on an HP300 + machine, say Y here. + +config HPAPCI + tristate "HP APCI serial support" + depends on HP300 && SERIAL_8250 && EXPERIMENTAL + help + If you want to use the internal "APCI" serial ports on an HP400 + machine, say Y here. + +config MVME147_SCC + bool "SCC support for MVME147 serial ports" + depends on MVME147 && BROKEN + help + This is the driver for the serial ports on the Motorola MVME147 + boards. Everyone using one of these boards should say Y here. + +config MVME162_SCC + bool "SCC support for MVME162 serial ports" + depends on MVME16x && BROKEN + help + This is the driver for the serial ports on the Motorola MVME162 and + 172 boards. Everyone using one of these boards should say Y here. + +config BVME6000_SCC + bool "SCC support for BVME6000 serial ports" + depends on BVME6000 && BROKEN + help + This is the driver for the serial ports on the BVME4000 and BVME6000 + boards from BVM Ltd. Everyone using one of these boards should say + Y here. + +config DN_SERIAL + bool "Support for DN serial port (dummy)" + depends on APOLLO + +config SERIAL_CONSOLE + bool "Support for serial port console" + depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL) + ---help--- + If you say Y here, it will be possible to use a serial port as the + system console (the system console is the device which receives all + kernel messages and warnings and which allows logins in single user + mode). This could be useful if some terminal or printer is connected + to that serial port. + + Even if you say Y here, the currently visible virtual console + (/dev/tty0) will still be used as the system console by default, but + you can alter that using a kernel command line option such as + "console=ttyS1". (Try "man bootparam" or see the documentation of + your boot loader (lilo or loadlin) about how to pass options to the + kernel at boot time.) + + If you don't have a VGA card installed and you say Y here, the + kernel will automatically use the first serial line, /dev/ttyS0, as + system console. + + If unsure, say N. + +endmenu + +endif diff --git a/arch/m68k/Kconfig.nommu b/arch/m68k/Kconfig.machine index ff46383112a..7d5c20b896c 100644 --- a/arch/m68k/Kconfig.nommu +++ b/arch/m68k/Kconfig.machine @@ -1,297 +1,142 @@ -config FPU - bool - default n - -config GENERIC_GPIO - bool - default n - -config GENERIC_CMOS_UPDATE - bool - default y - -config GENERIC_CLOCKEVENTS - bool - default n - -config M68000 - bool - select CPU_HAS_NO_BITFIELDS - help - The Freescale (was Motorola) 68000 CPU is the first generation of - the well known M68K family of processors. The CPU core as well as - being available as a stand alone CPU was also used in many - System-On-Chip devices (eg 68328, 68302, etc). It does not contain - a paging MMU. - -config MCPU32 - bool - select CPU_HAS_NO_BITFIELDS - help - The Freescale (was then Motorola) CPU32 is a CPU core that is - based on the 68020 processor. For the most part it is used in - System-On-Chip parts, and does not contain a paging MMU. - -config COLDFIRE - bool - select GENERIC_GPIO - select ARCH_REQUIRE_GPIOLIB - select CPU_HAS_NO_BITFIELDS - help - The Freescale ColdFire family of processors is a modern derivitive - of the 68000 processor family. They are mainly targeted at embedded - applications, and are all System-On-Chip (SOC) devices, as opposed - to stand alone CPUs. They implement a subset of the original 68000 - processor instruction set. - -config COLDFIRE_SW_A7 - bool - default n - -config HAVE_CACHE_SPLIT - bool - -config HAVE_CACHE_CB - bool - -config HAVE_MBAR - bool - -config HAVE_IPSBAR - bool - -choice - prompt "CPU" - default M68EZ328 - -config M68328 - bool "MC68328" - select M68000 - help - Motorola 68328 processor support. - -config M68EZ328 - bool "MC68EZ328" - select M68000 - help - Motorola 68EX328 processor support. - -config M68VZ328 - bool "MC68VZ328" - select M68000 - help - Motorola 68VZ328 processor support. - -config M68360 - bool "MC68360" - select MCPU32 - help - Motorola 68360 processor support. - -config M5206 - bool "MCF5206" - select COLDFIRE - select COLDFIRE_SW_A7 - select HAVE_MBAR - help - Motorola ColdFire 5206 processor support. +comment "Machine Types" + +config AMIGA + bool "Amiga support" + depends on MMU + select MMU_MOTOROLA if MMU + help + This option enables support for the Amiga series of computers. If + you plan to use this kernel on an Amiga, say Y here and browse the + material available in <file:Documentation/m68k>; otherwise say N. + +config ATARI + bool "Atari support" + depends on MMU + select MMU_MOTOROLA if MMU + help + This option enables support for the 68000-based Atari series of + computers (including the TT, Falcon and Medusa). If you plan to use + this kernel on an Atari, say Y here and browse the material + available in <file:Documentation/m68k>; otherwise say N. + +config MAC + bool "Macintosh support" + depends on MMU + select MMU_MOTOROLA if MMU + help + This option enables support for the Apple Macintosh series of + computers (yes, there is experimental support now, at least for part + of the series). + + Say N unless you're willing to code the remaining necessary support. + ;) + +config APOLLO + bool "Apollo support" + depends on MMU + select MMU_MOTOROLA if MMU + help + Say Y here if you want to run Linux on an MC680x0-based Apollo + Domain workstation such as the DN3500. + +config VME + bool "VME (Motorola and BVM) support" + depends on MMU + select MMU_MOTOROLA if MMU + help + Say Y here if you want to build a kernel for a 680x0 based VME + board. Boards currently supported include Motorola boards MVME147, + MVME162, MVME166, MVME167, MVME172, and MVME177. BVME4000 and + BVME6000 boards from BVM Ltd are also supported. + +config MVME147 + bool "MVME147 support" + depends on MMU + depends on VME + help + Say Y to include support for early Motorola VME boards. This will + build a kernel which can run on MVME147 single-board computers. If + you select this option you will have to select the appropriate + drivers for SCSI, Ethernet and serial ports later on. + +config MVME16x + bool "MVME162, 166 and 167 support" + depends on MMU + depends on VME + help + Say Y to include support for Motorola VME boards. This will build a + kernel which can run on MVME162, MVME166, MVME167, MVME172, and + MVME177 boards. If you select this option you will have to select + the appropriate drivers for SCSI, Ethernet and serial ports later + on. + +config BVME6000 + bool "BVME4000 and BVME6000 support" + depends on MMU + depends on VME + help + Say Y to include support for VME boards from BVM Ltd. This will + build a kernel which can run on BVME4000 and BVME6000 boards. If + you select this option you will have to select the appropriate + drivers for SCSI, Ethernet and serial ports later on. + +config HP300 + bool "HP9000/300 and HP9000/400 support" + depends on MMU + select MMU_MOTOROLA if MMU + help + This option enables support for the HP9000/300 and HP9000/400 series + of workstations. Support for these machines is still somewhat + experimental. If you plan to try to use the kernel on such a machine + say Y here. + Everybody else says N. + +config SUN3X + bool "Sun3x support" + depends on MMU + select MMU_MOTOROLA if MMU + select M68030 + help + This option enables support for the Sun 3x series of workstations. + Be warned that this support is very experimental. + Note that Sun 3x kernels are not compatible with Sun 3 hardware. + General Linux information on the Sun 3x series (now discontinued) + is at <http://www.angelfire.com/ca2/tech68k/sun3.html>. + + If you don't want to compile a kernel for a Sun 3x, say N. + +config Q40 + bool "Q40/Q60 support" + depends on MMU + select MMU_MOTOROLA if MMU + help + The Q40 is a Motorola 68040-based successor to the Sinclair QL + manufactured in Germany. There is an official Q40 home page at + <http://www.q40.de/>. This option enables support for the Q40 and + Q60. Select your CPU below. For 68LC060 don't forget to enable FPU + emulation. + +config SUN3 + bool "Sun3 support" + depends on MMU + depends on !MMU_MOTOROLA + select MMU_SUN3 if MMU + select M68020 + help + This option enables support for the Sun 3 series of workstations + (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires + that all other hardware types must be disabled, as Sun 3 kernels + are incompatible with all other m68k targets (including Sun 3x!). + + If you don't want to compile a kernel exclusively for a Sun 3, say N. -config M5206e - bool "MCF5206e" - select COLDFIRE - select COLDFIRE_SW_A7 - select HAVE_MBAR - help - Motorola ColdFire 5206e processor support. - -config M520x - bool "MCF520x" - select COLDFIRE - select GENERIC_CLOCKEVENTS - select HAVE_CACHE_SPLIT - help - Freescale Coldfire 5207/5208 processor support. - -config M523x - bool "MCF523x" - select COLDFIRE - select GENERIC_CLOCKEVENTS - select HAVE_CACHE_SPLIT - select HAVE_IPSBAR - help - Freescale Coldfire 5230/1/2/4/5 processor support - -config M5249 - bool "MCF5249" - select COLDFIRE - select COLDFIRE_SW_A7 - select HAVE_MBAR - help - Motorola ColdFire 5249 processor support. - -config M5271 - bool "MCF5271" - select COLDFIRE - select HAVE_CACHE_SPLIT - select HAVE_IPSBAR - help - Freescale (Motorola) ColdFire 5270/5271 processor support. - -config M5272 - bool "MCF5272" - select COLDFIRE - select COLDFIRE_SW_A7 - select HAVE_MBAR - help - Motorola ColdFire 5272 processor support. - -config M5275 - bool "MCF5275" - select COLDFIRE - select HAVE_CACHE_SPLIT - select HAVE_IPSBAR - help - Freescale (Motorola) ColdFire 5274/5275 processor support. - -config M528x - bool "MCF528x" - select COLDFIRE - select GENERIC_CLOCKEVENTS - select HAVE_CACHE_SPLIT - select HAVE_IPSBAR - help - Motorola ColdFire 5280/5282 processor support. - -config M5307 - bool "MCF5307" - select COLDFIRE - select COLDFIRE_SW_A7 - select HAVE_CACHE_CB - select HAVE_MBAR - help - Motorola ColdFire 5307 processor support. - -config M532x - bool "MCF532x" - select COLDFIRE - select HAVE_CACHE_CB - help - Freescale (Motorola) ColdFire 532x processor support. - -config M5407 - bool "MCF5407" - select COLDFIRE - select COLDFIRE_SW_A7 - select HAVE_CACHE_CB - select HAVE_MBAR - help - Motorola ColdFire 5407 processor support. - -config M547x - bool "MCF547x" - select COLDFIRE - select HAVE_CACHE_CB - select HAVE_MBAR - help - Freescale ColdFire 5470/5471/5472/5473/5474/5475 processor support. - -config M548x - bool "MCF548x" - select COLDFIRE - select HAVE_CACHE_CB - select HAVE_MBAR - help - Freescale ColdFire 5480/5481/5482/5483/5484/5485 processor support. - -endchoice - -config M527x - bool - depends on (M5271 || M5275) - select GENERIC_CLOCKEVENTS - default y - -config M54xx +config PILOT bool - depends on (M548x || M547x) - default y - -config CLOCK_SET - bool "Enable setting the CPU clock frequency" - default n - help - On some CPU's you do not need to know what the core CPU clock - frequency is. On these you can disable clock setting. On some - traditional 68K parts, and on all ColdFire parts you need to set - the appropriate CPU clock frequency. On these devices many of the - onboard peripherals derive their timing from the master CPU clock - frequency. - -config CLOCK_FREQ - int "Set the core clock frequency" - default "66666666" - depends on CLOCK_SET - help - Define the CPU clock frequency in use. This is the core clock - frequency, it may or may not be the same as the external clock - crystal fitted to your board. Some processors have an internal - PLL and can have their frequency programmed at run time, others - use internal dividers. In general the kernel won't setup a PLL - if it is fitted (there are some exceptions). This value will be - specific to the exact CPU that you are using. - -config OLDMASK - bool "Old mask 5307 (1H55J) silicon" - depends on M5307 - help - Build support for the older revision ColdFire 5307 silicon. - Specifically this is the 1H55J mask revision. - -if HAVE_CACHE_SPLIT -choice - prompt "Split Cache Configuration" - default CACHE_I - -config CACHE_I - bool "Instruction" - help - Use all of the ColdFire CPU cache memory as an instruction cache. - -config CACHE_D - bool "Data" - help - Use all of the ColdFire CPU cache memory as a data cache. - -config CACHE_BOTH - bool "Both" - help - Split the ColdFire CPU cache, and use half as an instruction cache - and half as a data cache. -endchoice -endif - -if HAVE_CACHE_CB -choice - prompt "Data cache mode" - default CACHE_WRITETHRU - -config CACHE_WRITETHRU - bool "Write-through" - help - The ColdFire CPU cache is set into Write-through mode. - -config CACHE_COPYBACK - bool "Copy-back" - help - The ColdFire CPU cache is set into Copy-back mode. -endchoice -endif - -comment "Platform" config PILOT3 bool "Pilot 1000/5000, PalmPilot Personal/Pro, or PalmIII support" depends on M68328 + select PILOT help Support for the Palm Pilot 1000/5000, Personal/Pro and PalmIII. @@ -302,7 +147,7 @@ config XCOPILOT_BUGS Support the bugs of Xcopilot. config UC5272 - bool 'Arcturus Networks uC5272 dimm board support' + bool "Arcturus Networks uC5272 dimm board support" depends on M5272 help Support for the Arcturus Networks uC5272 dimm board. @@ -356,15 +201,23 @@ config UCQUICC help Support for the Lineo uCquicc board. +config ARNEWSH + bool + config ARN5206 bool "Arnewsh 5206 board support" depends on M5206 + select ARNEWSH help Support for the Arnewsh 5206 board. +config FREESCALE + bool + config M5206eC3 bool "Motorola M5206eC3 board support" depends on M5206e + select FREESCALE help Support for the Motorola M5206eC3 board. @@ -377,75 +230,95 @@ config ELITE config M5208EVB bool "Freescale M5208EVB board support" depends on M520x + select FREESCALE help Support for the Freescale Coldfire M5208EVB. config M5235EVB bool "Freescale M5235EVB support" depends on M523x + select FREESCALE help Support for the Freescale M5235EVB board. config M5249C3 bool "Motorola M5249C3 board support" depends on M5249 + select FREESCALE help Support for the Motorola M5249C3 board. config M5271EVB bool "Freescale (Motorola) M5271EVB board support" depends on M5271 + select FREESCALE help Support for the Freescale (Motorola) M5271EVB board. config M5275EVB bool "Freescale (Motorola) M5275EVB board support" depends on M5275 + select FREESCALE help Support for the Freescale (Motorola) M5275EVB board. config M5272C3 bool "Motorola M5272C3 board support" depends on M5272 + select FREESCALE help Support for the Motorola M5272C3 board. +config senTec + bool + config COBRA5272 bool "senTec COBRA5272 board support" depends on M5272 + select senTec help Support for the senTec COBRA5272 board. +config AVNET + bool + config AVNET5282 bool "Avnet 5282 board support" depends on M528x + select AVNET help - Support for the Avnet 5282 board. - + Support for the Avnet 5282 board. + config M5282EVB bool "Motorola M5282EVB board support" depends on M528x + select FREESCALE help Support for the Motorola M5282EVB board. config COBRA5282 bool "senTec COBRA5282 board support" depends on M528x + select senTec help Support for the senTec COBRA5282 board. - + +config EMAC_INC + bool + config SOM5282EM bool "EMAC.Inc SOM5282EM board support" depends on M528x + select EMAC_INC help - Support for the EMAC.Inc SOM5282EM module. - + Support for the EMAC.Inc SOM5282EM module. + config WILDFIRE bool "Intec Automation Inc. WildFire board support" depends on M528x help Support for the Intec Automation Inc. WildFire. - + config WILDFIREMOD bool "Intec Automation Inc. WildFire module support" depends on M528x @@ -455,12 +328,14 @@ config WILDFIREMOD config ARN5307 bool "Arnewsh 5307 board support" depends on M5307 + select ARNEWSH help Support for the Arnewsh 5307 board. config M5307C3 bool "Motorola M5307C3 board support" depends on M5307 + select FREESCALE help Support for the Motorola M5307C3 board. @@ -473,6 +348,7 @@ config SECUREEDGEMP3 config M5329EVB bool "Freescale (Motorola) M5329EVB board support" depends on M532x + select FREESCALE help Support for the Freescale (Motorola) M5329EVB board. @@ -485,6 +361,7 @@ config COBRA5329 config M5407C3 bool "Motorola M5407C3 board support" depends on M5407 + select FREESCALE help Support for the Motorola M5407C3 board. @@ -494,21 +371,27 @@ config FIREBEE help Support for the FireBee ColdFire 5475 based board. +config HW_FEITH + bool + config CLEOPATRA bool "Feith CLEOPATRA board support" depends on (M5307 || M5407) + select HW_FEITH help Support for the Feith Cleopatra boards. config CANCam bool "Feith CANCam board support" depends on M5272 + select HW_FEITH help Support for the Feith CANCam board. config SCALES bool "Feith SCALES board support" depends on M5272 + select HW_FEITH help Support for the Feith SCALES board. @@ -524,9 +407,13 @@ config SNAPGEAR help Special additional support for SnapGear router boards. +config SNEHA + bool + config CPU16B bool "Sneha Technologies S.L. Sarasvati board support" depends on M5272 + select SNEHA help Support for the SNEHA CPU16B board. @@ -536,12 +423,21 @@ config MOD5272 help Support for the Netburner MOD-5272 board. +config SAVANT + bool + config SAVANTrosie1 bool "Savant Rosie1 board support" depends on M523x + select SAVANT help Support for the Savant Rosie1 board. + +if !MMU || COLDFIRE + +comment "Machine Options" + config ROMFS_FROM_ROM bool "ROMFS image not RAM resident" depends on (NETtel || SNAPGEAR) @@ -549,51 +445,6 @@ config ROMFS_FROM_ROM The ROMfs filesystem will stay resident in the FLASH/ROM, not be moved into RAM. -config PILOT - bool - default y - depends on (PILOT3 || PILOT5) - -config ARNEWSH - bool - default y - depends on (ARN5206 || ARN5307) - -config FREESCALE - bool - default y - depends on (M5206eC3 || M5208EVB || M5235EVB || M5249C3 || M5271EVB || M5272C3 || M5275EVB || M5282EVB || M5307C3 || M5329EVB || M5407C3) - -config HW_FEITH - bool - default y - depends on (CLEOPATRA || CANCam || SCALES) - -config senTec - bool - default y - depends on (COBRA5272 || COBRA5282) - -config EMAC_INC - bool - default y - depends on (SOM5282EM) - -config SNEHA - bool - default y - depends on CPU16B - -config SAVANT - bool - default y - depends on SAVANTrosie1 - -config AVNET - bool - default y - depends on (AVNET5282) - config UBOOT bool "Support for U-Boot command line parameters" help @@ -772,16 +623,4 @@ config ROMKERNEL endchoice -if COLDFIRE -source "kernel/Kconfig.preempt" endif - -source "kernel/time/Kconfig" - -config ISA_DMA_API - bool - depends on !M5272 - default y - -source "drivers/pcmcia/Kconfig" - diff --git a/arch/m68k/Kconfig.mmu b/arch/m68k/Kconfig.mmu deleted file mode 100644 index 13e20bbc407..00000000000 --- a/arch/m68k/Kconfig.mmu +++ /dev/null @@ -1,411 +0,0 @@ -config GENERIC_IOMAP - bool - default y - -config ARCH_MAY_HAVE_PC_FDC - bool - depends on BROKEN && (Q40 || SUN3X) - default y - -config ARCH_USES_GETTIMEOFFSET - def_bool y - -config EISA - bool - ---help--- - The Extended Industry Standard Architecture (EISA) bus was - developed as an open alternative to the IBM MicroChannel bus. - - The EISA bus provided some of the features of the IBM MicroChannel - bus while maintaining backward compatibility with cards made for - the older ISA bus. The EISA bus saw limited use between 1988 and - 1995 when it was made obsolete by the PCI bus. - - Say Y here if you are building a kernel for an EISA-based machine. - - Otherwise, say N. - -config MCA - bool - help - MicroChannel Architecture is found in some IBM PS/2 machines and - laptops. It is a bus system similar to PCI or ISA. See - <file:Documentation/mca.txt> (and especially the web page given - there) before attempting to build an MCA bus kernel. - -config PCMCIA - tristate - ---help--- - Say Y here if you want to attach PCMCIA- or PC-cards to your Linux - computer. These are credit-card size devices such as network cards, - modems or hard drives often used with laptops computers. There are - actually two varieties of these cards: the older 16 bit PCMCIA cards - and the newer 32 bit CardBus cards. If you want to use CardBus - cards, you need to say Y here and also to "CardBus support" below. - - To use your PC-cards, you will need supporting software from David - Hinds' pcmcia-cs package (see the file <file:Documentation/Changes> - for location). Please also read the PCMCIA-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. - - To compile this driver as modules, choose M here: the - modules will be called pcmcia_core and ds. - -config AMIGA - bool "Amiga support" - select MMU_MOTOROLA if MMU - help - This option enables support for the Amiga series of computers. If - you plan to use this kernel on an Amiga, say Y here and browse the - material available in <file:Documentation/m68k>; otherwise say N. - -config ATARI - bool "Atari support" - select MMU_MOTOROLA if MMU - help - This option enables support for the 68000-based Atari series of - computers (including the TT, Falcon and Medusa). If you plan to use - this kernel on an Atari, say Y here and browse the material - available in <file:Documentation/m68k>; otherwise say N. - -config MAC - bool "Macintosh support" - select MMU_MOTOROLA if MMU - help - This option enables support for the Apple Macintosh series of - computers (yes, there is experimental support now, at least for part - of the series). - - Say N unless you're willing to code the remaining necessary support. - ;) - -config NUBUS - bool - depends on MAC - default y - -config M68K_L2_CACHE - bool - depends on MAC - default y - -config APOLLO - bool "Apollo support" - select MMU_MOTOROLA if MMU - help - Say Y here if you want to run Linux on an MC680x0-based Apollo - Domain workstation such as the DN3500. - -config VME - bool "VME (Motorola and BVM) support" - select MMU_MOTOROLA if MMU - help - Say Y here if you want to build a kernel for a 680x0 based VME - board. Boards currently supported include Motorola boards MVME147, - MVME162, MVME166, MVME167, MVME172, and MVME177. BVME4000 and - BVME6000 boards from BVM Ltd are also supported. - -config MVME147 - bool "MVME147 support" - depends on VME - help - Say Y to include support for early Motorola VME boards. This will - build a kernel which can run on MVME147 single-board computers. If - you select this option you will have to select the appropriate - drivers for SCSI, Ethernet and serial ports later on. - -config MVME16x - bool "MVME162, 166 and 167 support" - depends on VME - help - Say Y to include support for Motorola VME boards. This will build a - kernel which can run on MVME162, MVME166, MVME167, MVME172, and - MVME177 boards. If you select this option you will have to select - the appropriate drivers for SCSI, Ethernet and serial ports later - on. - -config BVME6000 - bool "BVME4000 and BVME6000 support" - depends on VME - help - Say Y to include support for VME boards from BVM Ltd. This will - build a kernel which can run on BVME4000 and BVME6000 boards. If - you select this option you will have to select the appropriate - drivers for SCSI, Ethernet and serial ports later on. - -config HP300 - bool "HP9000/300 and HP9000/400 support" - select MMU_MOTOROLA if MMU - help - This option enables support for the HP9000/300 and HP9000/400 series - of workstations. Support for these machines is still somewhat - experimental. If you plan to try to use the kernel on such a machine - say Y here. - Everybody else says N. - -config DIO - bool "DIO bus support" - depends on HP300 - default y - help - Say Y here to enable support for the "DIO" expansion bus used in - HP300 machines. If you are using such a system you almost certainly - want this. - -config SUN3X - bool "Sun3x support" - select MMU_MOTOROLA if MMU - select M68030 - help - This option enables support for the Sun 3x series of workstations. - Be warned that this support is very experimental. - Note that Sun 3x kernels are not compatible with Sun 3 hardware. - General Linux information on the Sun 3x series (now discontinued) - is at <http://www.angelfire.com/ca2/tech68k/sun3.html>. - - If you don't want to compile a kernel for a Sun 3x, say N. - -config Q40 - bool "Q40/Q60 support" - select MMU_MOTOROLA if MMU - help - The Q40 is a Motorola 68040-based successor to the Sinclair QL - manufactured in Germany. There is an official Q40 home page at - <http://www.q40.de/>. This option enables support for the Q40 and - Q60. Select your CPU below. For 68LC060 don't forget to enable FPU - emulation. - -config SUN3 - bool "Sun3 support" - depends on !MMU_MOTOROLA - select MMU_SUN3 if MMU - select M68020 - help - This option enables support for the Sun 3 series of workstations - (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires - that all other hardware types must be disabled, as Sun 3 kernels - are incompatible with all other m68k targets (including Sun 3x!). - - If you don't want to compile a kernel exclusively for a Sun 3, say N. - -config NATFEAT - bool "ARAnyM emulator support" - depends on ATARI - help - This option enables support for ARAnyM native features, such as - access to a disk image as /dev/hda. - -config NFBLOCK - tristate "NatFeat block device support" - depends on BLOCK && NATFEAT - help - Say Y to include support for the ARAnyM NatFeat block device - which allows direct access to the hard drives without using - the hardware emulation. - -config NFCON - tristate "NatFeat console driver" - depends on NATFEAT - help - Say Y to include support for the ARAnyM NatFeat console driver - which allows the console output to be redirected to the stderr - output of ARAnyM. - -config NFETH - tristate "NatFeat Ethernet support" - depends on NET_ETHERNET && NATFEAT - help - Say Y to include support for the ARAnyM NatFeat network device - which will emulate a regular ethernet device while presenting an - ethertap device to the host system. - -comment "Processor type" - -config M68020 - bool "68020 support" - help - If you anticipate running this kernel on a computer with a MC68020 - processor, say Y. Otherwise, say N. Note that the 68020 requires a - 68851 MMU (Memory Management Unit) to run Linux/m68k, except on the - Sun 3, which provides its own version. - -config M68030 - bool "68030 support" - depends on !MMU_SUN3 - help - If you anticipate running this kernel on a computer with a MC68030 - processor, say Y. Otherwise, say N. Note that a MC68EC030 will not - work, as it does not include an MMU (Memory Management Unit). - -config M68040 - bool "68040 support" - depends on !MMU_SUN3 - help - If you anticipate running this kernel on a computer with a MC68LC040 - or MC68040 processor, say Y. Otherwise, say N. Note that an - MC68EC040 will not work, as it does not include an MMU (Memory - Management Unit). - -config M68060 - bool "68060 support" - depends on !MMU_SUN3 - help - If you anticipate running this kernel on a computer with a MC68060 - processor, say Y. Otherwise, say N. - -config MMU_MOTOROLA - bool - -config MMU_SUN3 - bool - depends on MMU && !MMU_MOTOROLA - -config M68KFPU_EMU - bool "Math emulation support (EXPERIMENTAL)" - depends on EXPERIMENTAL - help - At some point in the future, this will cause floating-point math - instructions to be emulated by the kernel on machines that lack a - floating-point math coprocessor. Thrill-seekers and chronically - sleep-deprived psychotic hacker types can say Y now, everyone else - should probably wait a while. - -config M68KFPU_EMU_EXTRAPREC - bool "Math emulation extra precision" - depends on M68KFPU_EMU - help - The fpu uses normally a few bit more during calculations for - correct rounding, the emulator can (often) do the same but this - extra calculation can cost quite some time, so you can disable - it here. The emulator will then "only" calculate with a 64 bit - mantissa and round slightly incorrect, what is more than enough - for normal usage. - -config M68KFPU_EMU_ONLY - bool "Math emulation only kernel" - depends on M68KFPU_EMU - help - This option prevents any floating-point instructions from being - compiled into the kernel, thereby the kernel doesn't save any - floating point context anymore during task switches, so this - kernel will only be usable on machines without a floating-point - math coprocessor. This makes the kernel a bit faster as no tests - needs to be executed whether a floating-point instruction in the - kernel should be executed or not. - -config ADVANCED - bool "Advanced configuration options" - ---help--- - This gives you access to some advanced options for the CPU. The - defaults should be fine for most users, but these options may make - it possible for you to improve performance somewhat if you know what - you are doing. - - Note that the answer to this question won't directly affect the - kernel: saying N will just cause the configurator to skip all - the questions about these options. - - Most users should say N to this question. - -config RMW_INSNS - bool "Use read-modify-write instructions" - depends on ADVANCED - ---help--- - This allows to use certain instructions that work with indivisible - read-modify-write bus cycles. While this is faster than the - workaround of disabling interrupts, it can conflict with DMA - ( = direct memory access) on many Amiga systems, and it is also said - to destabilize other machines. It is very likely that this will - cause serious problems on any Amiga or Atari Medusa if set. The only - configuration where it should work are 68030-based Ataris, where it - apparently improves performance. But you've been warned! Unless you - really know what you are doing, say N. Try Y only if you're quite - adventurous. - -config SINGLE_MEMORY_CHUNK - bool "Use one physical chunk of memory only" if ADVANCED && !SUN3 - default y if SUN3 - select NEED_MULTIPLE_NODES - help - Ignore all but the first contiguous chunk of physical memory for VM - purposes. This will save a few bytes kernel size and may speed up - some operations. Say N if not sure. - -config 060_WRITETHROUGH - bool "Use write-through caching for 68060 supervisor accesses" - depends on ADVANCED && M68060 - ---help--- - The 68060 generally uses copyback caching of recently accessed data. - Copyback caching means that memory writes will be held in an on-chip - cache and only written back to memory some time later. Saying Y - here will force supervisor (kernel) accesses to use writethrough - caching. Writethrough caching means that data is written to memory - straight away, so that cache and memory data always agree. - Writethrough caching is less efficient, but is needed for some - drivers on 68060 based systems where the 68060 bus snooping signal - is hardwired on. The 53c710 SCSI driver is known to suffer from - this problem. - -config ARCH_DISCONTIGMEM_ENABLE - def_bool !SINGLE_MEMORY_CHUNK - -config NODES_SHIFT - int - default "3" - depends on !SINGLE_MEMORY_CHUNK - -config ZORRO - bool "Amiga Zorro (AutoConfig) bus support" - depends on AMIGA - help - This enables support for the Zorro bus in the Amiga. If you have - expansion cards in your Amiga that conform to the Amiga - AutoConfig(tm) specification, say Y, otherwise N. Note that even - expansion cards that do not fit in the Zorro slots but fit in e.g. - the CPU slot may fall in this category, so you have to say Y to let - Linux use these. - -config AMIGA_PCMCIA - bool "Amiga 1200/600 PCMCIA support (EXPERIMENTAL)" - depends on AMIGA && EXPERIMENTAL - help - Include support in the kernel for pcmcia on Amiga 1200 and Amiga - 600. If you intend to use pcmcia cards say Y; otherwise say N. - -config HEARTBEAT - bool "Use power LED as a heartbeat" if AMIGA || APOLLO || ATARI || MAC ||Q40 - default y if !AMIGA && !APOLLO && !ATARI && !MAC && !Q40 && HP300 - help - Use the power-on LED on your machine as a load meter. The exact - behavior is platform-dependent, but normally the flash frequency is - a hyperbolic function of the 5-minute load average. - -# We have a dedicated heartbeat LED. :-) -config PROC_HARDWARE - bool "/proc/hardware support" - help - Say Y here to support the /proc/hardware file, which gives you - access to information about the machine you're running on, - including the model, CPU, MMU, clock speed, BogoMIPS rating, - and memory size. - -config ISA - bool - depends on Q40 || AMIGA_PCMCIA - default y - help - Find out whether you have ISA slots on your motherboard. ISA is the - name of a bus system, i.e. the way the CPU talks to the other stuff - inside your box. Other bus systems are PCI, EISA, MicroChannel - (MCA) or VESA. ISA is an older system, now being displaced by PCI; - newer boards don't support it. If you have ISA, say Y, otherwise N. - -config GENERIC_ISA_DMA - bool - depends on Q40 || AMIGA_PCMCIA - default y - -source "drivers/pci/Kconfig" - -source "drivers/zorro/Kconfig" - |