diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/blackfin/Kconfig | 15 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/H8606.c | 345 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf533/boards/Makefile | 1 |
3 files changed, 359 insertions, 2 deletions
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig index 7888551ed93..9f9de3e9582 100644 --- a/arch/blackfin/Kconfig +++ b/arch/blackfin/Kconfig @@ -295,6 +295,12 @@ config PNAV10 help PNAV 1.0 board Support. +config H8606_HVSISTEMAS + bool "HV Sistemas H8606" + depends on (BF532) + help + HV Sistemas H8606 board support. + config GENERIC_BOARD bool "Custom" depends on (BF537 || BF536 \ @@ -317,7 +323,8 @@ config MEM_MT48LC64M4A2FB_7E config MEM_MT48LC16M16A2TG_75 bool depends on (BFIN533_EZKIT || BFIN561_EZKIT \ - || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM) + || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \ + || H8606_HVSISTEMAS) default y config MEM_MT48LC32M8A2_75 @@ -366,7 +373,7 @@ config CLKIN_HZ int "Crystal Frequency in Hz" default "11059200" if BFIN533_STAMP default "27000000" if BFIN533_EZKIT - default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT) + default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS) default "30000000" if BFIN561_EZKIT default "24576000" if PNAV10 help @@ -404,6 +411,7 @@ config VCO_MULT default "20" if BFIN537_BLUETECHNIX_CM default "20" if BFIN561_BLUETECHNIX_CM default "20" if BFIN561_EZKIT + default "16" if H8606_HVSISTEMAS help This controls the frequency of the on-chip PLL. This can be between 1 and 64. PLL Frequency = (Crystal Frequency) * (this setting) @@ -440,6 +448,7 @@ config SCLK_DIV default 4 if BFIN537_BLUETECHNIX_CM default 4 if BFIN561_BLUETECHNIX_CM default 5 if BFIN561_EZKIT + default 3 if H8606_HVSISTEMAS help This sets the frequency of the system clock (including SDRAM or DDR). This can be between 1 and 15 @@ -492,11 +501,13 @@ config MEM_SIZE default 64 if BFIN561_EZKIT default 128 if BFIN533_STAMP default 64 if PNAV10 + default 32 if H8606_HVSISTEMAS config MEM_ADD_WIDTH int "SDRAM Memory Address Width" default 9 if BFIN533_EZKIT default 9 if BFIN561_EZKIT + default 9 if H8606_HVSISTEMAS default 10 if BFIN527_EZKIT default 10 if BFIN537_STAMP default 11 if BFIN533_STAMP diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c new file mode 100644 index 00000000000..b941550f956 --- /dev/null +++ b/arch/blackfin/mach-bf533/boards/H8606.c @@ -0,0 +1,345 @@ +/* + * File: arch/blackfin/mach-bf533/H8606.c + * Based on: arch/blackfin/mach-bf533/stamp.c + * Author: Javier Herrero <jherrero@hvsistemas.es> + * + * Created: 2007 + * Description: Board Info File for the HV Sistemas H8606 board + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2006 Analog Devices Inc + * Copyright 2007 HV Sistemas S.L. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/spi/spi.h> +#include <linux/spi/flash.h> +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#include <linux/usb_isp1362.h> +#endif +#include <linux/pata_platform.h> +#include <linux/irq.h> +#include <asm/dma.h> +#include <asm/bfin5xx_spi.h> +#include <asm/reboot.h> + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "HV Sistemas H8606"; + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +/* +* Driver needs to know address, irq and flag pin. + */ + #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) +static struct resource dm9000_resources[] = { + [0] = { + .start = 0x20300000, + .end = 0x20300000 + 8, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_PF10, + .end = IRQ_PF10, + .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE), + }, +}; + +static struct platform_device dm9000_device = { + .id = 0, + .name = "dm9000", + .resource = dm9000_resources, + .num_resources = ARRAY_SIZE(dm9000_resources), +}; +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .name = "smc91x-regs", + .start = 0x20300300, + .end = 0x20300300 + 16, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PROG_INTB, + .end = IRQ_PROG_INTB, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, { + /* + * denotes the flag pin and is used directly if + * CONFIG_IRQCHIP_DEMUX_GPIO is defined. + */ + .start = IRQ_PF7, + .end = IRQ_PF7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +static struct resource net2272_bfin_resources[] = { + { + .start = 0x20300000, + .end = 0x20300000 + 0x100, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF10, + .end = IRQ_PF10, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device net2272_bfin_device = { + .name = "net2272", + .id = -1, + .num_resources = ARRAY_SIZE(net2272_bfin_resources), + .resource = net2272_bfin_resources, +}; +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader", + .size = 0x00060000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "kernel", + .size = 0x100000, + .offset = 0x60000 + }, { + .name = "file system", + .size = 0x6a0000, + .offset = 0x00160000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .ctl_reg = 0x1000, + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .ctl_reg = 0x1000, + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_PBX) +static struct bfin5xx_spi_chip spi_si3xxx_chip_info = { + .ctl_reg = 0x1c04, + .enable_dma = 0, + .bits_per_word = 8, + .cs_change_per_word = 1, +}; +#endif + +/* Notice: for blackfin, the speed_hz is the value of register + * SPI_BAUD, not the real baudrate */ +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + /* this value is the baudrate divisor */ + .max_speed_hz = 50000000, /* actual baudrate is SCLK/(2xspeed_hz) */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 4, /* actual baudrate is SCLK/(2xspeed_hz) */ + .bus_num = 1, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836-spi", + .max_speed_hz = 16, + .bus_num = 1, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif + +#if defined(CONFIG_PBX) + { + .modalias = "fxs-spi", + .max_speed_hz = 4, + .bus_num = 1, + .chip_select = 3, + .controller_data = &spi_si3xxx_chip_info, + }, + + { + .modalias = "fxo-spi", + .max_speed_hz = 4, + .bus_num = 1, + .chip_select = 2, + .controller_data = &spi_si3xxx_chip_info, + }, +#endif +}; + +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_IRQ, + } +}; + + +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE) +static struct platform_device bfin_fb_device = { + .name = "bf537-fb", +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +static struct platform_device *stamp_devices[] __initdata = { +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) + &dm9000_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) + &net2272_bfin_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif +}; + +static int __init H8606_init(void) +{ + printk(KERN_INFO "HV Sistemas H8606 board support by http://www.hvsistemas.com\n"); + printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__); + platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); +#endif + return 0; +} + +arch_initcall(H8606_init);
\ No newline at end of file diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile index 12a631ab389..2452b456ccb 100644 --- a/arch/blackfin/mach-bf533/boards/Makefile +++ b/arch/blackfin/mach-bf533/boards/Makefile @@ -6,3 +6,4 @@ obj-$(CONFIG_GENERIC_BOARD) += generic_board.o obj-$(CONFIG_BFIN533_STAMP) += stamp.o obj-$(CONFIG_BFIN533_EZKIT) += ezkit.o obj-$(CONFIG_BFIN533_BLUETECHNIX_CM) += cm_bf533.o +obj-$(CONFIG_H8606_HVSISTEMAS) += H8606.o |