diff options
Diffstat (limited to 'arch')
118 files changed, 3581 insertions, 1806 deletions
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 62d686f0b42..d13add71f72 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -65,7 +65,7 @@ obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o -obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o +obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o board-stamp9g20.o # AT91SAM9260/AT91SAM9G20 board-specific support obj-$(CONFIG_MACH_SNAPPER_9260) += board-snapper9260.o diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c index bba5a560e02..feb65787c30 100644 --- a/arch/arm/mach-at91/board-pcontrol-g20.c +++ b/arch/arm/mach-at91/board-pcontrol-g20.c @@ -31,6 +31,7 @@ #include <mach/board.h> #include <mach/at91sam9_smc.h> +#include <mach/stamp9g20.h> #include "sam9_smc.h" #include "generic.h" @@ -38,11 +39,7 @@ static void __init pcontrol_g20_map_io(void) { - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */ - at91_register_uart(0, 0, 0); + stamp9g20_map_io(); /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS @@ -54,9 +51,6 @@ static void __init pcontrol_g20_map_io(void) /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */ at91_register_uart(AT91SAM9260_ID_US4, 3, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } @@ -66,38 +60,6 @@ static void __init init_irq(void) } -/* - * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB - */ -static struct atmel_nand_data __initdata nand_data = { - .ale = 21, - .cle = 22, - .rdy_pin = AT91_PIN_PC13, - .enable_pin = AT91_PIN_PC14, -}; - -/* - * Bus timings; unit = 7.57ns - */ -static struct sam9_smc_config __initdata nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 2, - .ncs_write_setup = 0, - .nwe_setup = 2, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 7, - .write_cycle = 7, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE - | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8, - .tdf_cycles = 3, -}; - static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { .ncs_read_setup = 16, .nrd_setup = 18, @@ -138,14 +100,6 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { .tdf_cycles = 1, } }; -static void __init add_device_nand(void) -{ - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &nand_smc_config); - at91_add_device_nand(&nand_data); -} - - static void __init add_device_pcontrol(void) { /* configure chip-select 4 (IO compatible to 8051 X4 ) */ @@ -156,23 +110,6 @@ static void __init add_device_pcontrol(void) /* - * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected - */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) -static struct mci_platform_data __initdata mmc_data = { - .slot[0] = { - .bus_width = 4, - }, -}; -#else -static struct at91_mmc_data __initdata mmc_data = { - .wire4 = 1, -}; -#endif - - -/* * USB Host port */ static struct at91_usbh_data __initdata usbh_data = { @@ -265,42 +202,13 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = { }; -/* - * Dallas 1-Wire DS2431 - */ -static struct w1_gpio_platform_data w1_gpio_pdata = { - .pin = AT91_PIN_PA29, - .is_open_drain = 1, -}; - -static struct platform_device w1_device = { - .name = "w1-gpio", - .id = -1, - .dev.platform_data = &w1_gpio_pdata, -}; - -static void add_wire1(void) -{ - at91_set_GPIO_periph(w1_gpio_pdata.pin, 1); - at91_set_multi_drive(w1_gpio_pdata.pin, 1); - platform_device_register(&w1_device); -} - - static void __init pcontrol_g20_board_init(void) { - at91_add_device_serial(); - add_device_nand(); -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) - at91_add_device_mci(0, &mmc_data); -#else - at91_add_device_mmc(0, &mmc_data); -#endif + stamp9g20_board_init(); at91_add_device_usbh(&usbh_data); at91_add_device_eth(&macb_data); at91_add_device_i2c(pcontrol_g20_i2c_devices, ARRAY_SIZE(pcontrol_g20_i2c_devices)); - add_wire1(); add_device_pcontrol(); at91_add_device_spi(pcontrol_g20_spi_devices, ARRAY_SIZE(pcontrol_g20_spi_devices)); diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 5206eef4a67..f8902b11896 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -32,7 +32,7 @@ #include "generic.h" -static void __init portuxg20_map_io(void) +void __init stamp9g20_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ at91sam9260_initialize(18432000); @@ -40,6 +40,24 @@ static void __init portuxg20_map_io(void) /* DGBU on ttyS0. (Rx & Tx only) */ at91_register_uart(0, 0, 0); + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init stamp9g20evb_map_io(void) +{ + stamp9g20_map_io(); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); +} + +static void __init portuxg20_map_io(void) +{ + stamp9g20_map_io(); + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR @@ -56,26 +74,6 @@ static void __init portuxg20_map_io(void) /* USART5 on ttyS6. (Rx, Tx only) */ at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init stamp9g20_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static void __init init_irq(void) @@ -156,7 +154,7 @@ static struct at91_udc_data __initdata portuxg20_udc_data = { .pullup_pin = 0, /* pull-up driven by UDC */ }; -static struct at91_udc_data __initdata stamp9g20_udc_data = { +static struct at91_udc_data __initdata stamp9g20evb_udc_data = { .vbus_pin = AT91_PIN_PA22, .pullup_pin = 0, /* pull-up driven by UDC */ }; @@ -190,7 +188,7 @@ static struct gpio_led portuxg20_leds[] = { } }; -static struct gpio_led stamp9g20_leds[] = { +static struct gpio_led stamp9g20evb_leds[] = { { .name = "D8", .gpio = AT91_PIN_PB18, @@ -250,7 +248,7 @@ void add_w1(void) } -static void __init generic_board_init(void) +void __init stamp9g20_board_init(void) { /* Serial */ at91_add_device_serial(); @@ -262,34 +260,40 @@ static void __init generic_board_init(void) #else at91_add_device_mmc(0, &mmc_data); #endif - /* USB Host */ - at91_add_device_usbh(&usbh_data); - /* Ethernet */ - at91_add_device_eth(&macb_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); /* W1 */ add_w1(); } static void __init portuxg20_board_init(void) { - generic_board_init(); - /* SPI */ - at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices)); + stamp9g20_board_init(); + /* USB Host */ + at91_add_device_usbh(&usbh_data); /* USB Device */ at91_add_device_udc(&portuxg20_udc_data); + /* Ethernet */ + at91_add_device_eth(&macb_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* SPI */ + at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices)); /* LEDs */ at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds)); } -static void __init stamp9g20_board_init(void) +static void __init stamp9g20evb_board_init(void) { - generic_board_init(); + stamp9g20_board_init(); + /* USB Host */ + at91_add_device_usbh(&usbh_data); /* USB Device */ - at91_add_device_udc(&stamp9g20_udc_data); + at91_add_device_udc(&stamp9g20evb_udc_data); + /* Ethernet */ + at91_add_device_eth(&macb_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); /* LEDs */ - at91_gpio_leds(stamp9g20_leds, ARRAY_SIZE(stamp9g20_leds)); + at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds)); } MACHINE_START(PORTUXG20, "taskit PortuxG20") @@ -305,7 +309,7 @@ MACHINE_START(STAMP9G20, "taskit Stamp9G20") /* Maintainer: taskit GmbH */ .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, - .map_io = stamp9g20_map_io, + .map_io = stamp9g20evb_map_io, .init_irq = init_irq, - .init_machine = stamp9g20_board_init, + .init_machine = stamp9g20evb_board_init, MACHINE_END diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index 7525cee3983..9113da6845f 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -658,7 +658,7 @@ static void __init at91_upll_usbfs_clock_init(unsigned long main_clock) /* Now set uhpck values */ uhpck.parent = &utmi_clk; uhpck.pmc_mask = AT91SAM926x_PMC_UHP; - uhpck.rate_hz = utmi_clk.parent->rate_hz; + uhpck.rate_hz = utmi_clk.rate_hz; uhpck.rate_hz /= 1 + ((at91_sys_read(AT91_PMC_USB) & AT91_PMC_OHCIUSBDIV) >> 8); } diff --git a/arch/arm/mach-at91/include/mach/stamp9g20.h b/arch/arm/mach-at91/include/mach/stamp9g20.h new file mode 100644 index 00000000000..6120f9c46d5 --- /dev/null +++ b/arch/arm/mach-at91/include/mach/stamp9g20.h @@ -0,0 +1,7 @@ +#ifndef __MACH_STAMP9G20_H +#define __MACH_STAMP9G20_H + +void stamp9g20_map_io(void); +void stamp9g20_board_init(void); + +#endif diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile index 0b1c07ffa2f..6ee19504845 100644 --- a/arch/arm/mach-omap1/Makefile +++ b/arch/arm/mach-omap1/Makefile @@ -3,7 +3,7 @@ # # Common support -obj-y := io.o id.o sram.o irq.o mux.o flash.o serial.o devices.o +obj-y := io.o id.o sram.o irq.o mux.o flash.o serial.o devices.o dma.o obj-y += clock.o clock_data.o opp_data.o obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index e1439506eba..bd0495a9ac3 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -43,84 +43,82 @@ static u8 ams_delta_latch1_reg; static u16 ams_delta_latch2_reg; -static int ams_delta_keymap[] = { +static const unsigned int ams_delta_keymap[] = { KEY(0, 0, KEY_F1), /* Advert */ - KEY(3, 0, KEY_COFFEE), /* Games */ - KEY(2, 0, KEY_QUESTION), /* Directory */ - KEY(3, 2, KEY_CONNECT), /* Internet */ - KEY(2, 1, KEY_SHOP), /* Services */ + KEY(0, 3, KEY_COFFEE), /* Games */ + KEY(0, 2, KEY_QUESTION), /* Directory */ + KEY(2, 3, KEY_CONNECT), /* Internet */ + KEY(1, 2, KEY_SHOP), /* Services */ KEY(1, 1, KEY_PHONE), /* VoiceMail */ - KEY(1, 0, KEY_DELETE), /* Delete */ + KEY(0, 1, KEY_DELETE), /* Delete */ KEY(2, 2, KEY_PLAY), /* Play */ - KEY(0, 1, KEY_PAGEUP), /* Up */ - KEY(3, 1, KEY_PAGEDOWN), /* Down */ - KEY(0, 2, KEY_EMAIL), /* ReadEmail */ - KEY(1, 2, KEY_STOP), /* Stop */ + KEY(1, 0, KEY_PAGEUP), /* Up */ + KEY(1, 3, KEY_PAGEDOWN), /* Down */ + KEY(2, 0, KEY_EMAIL), /* ReadEmail */ + KEY(2, 1, KEY_STOP), /* Stop */ /* Numeric keypad portion */ - KEY(7, 0, KEY_KP1), - KEY(6, 0, KEY_KP2), - KEY(5, 0, KEY_KP3), - KEY(7, 1, KEY_KP4), - KEY(6, 1, KEY_KP5), - KEY(5, 1, KEY_KP6), - KEY(7, 2, KEY_KP7), - KEY(6, 2, KEY_KP8), - KEY(5, 2, KEY_KP9), - KEY(6, 3, KEY_KP0), - KEY(7, 3, KEY_KPASTERISK), - KEY(5, 3, KEY_KPDOT), /* # key */ - KEY(2, 7, KEY_NUMLOCK), /* Mute */ - KEY(1, 7, KEY_KPMINUS), /* Recall */ - KEY(1, 6, KEY_KPPLUS), /* Redial */ - KEY(6, 7, KEY_KPSLASH), /* Handsfree */ - KEY(0, 6, KEY_ENTER), /* Video */ - - KEY(4, 7, KEY_CAMERA), /* Photo */ - - KEY(4, 0, KEY_F2), /* Home */ - KEY(4, 1, KEY_F3), /* Office */ - KEY(4, 2, KEY_F4), /* Mobile */ + KEY(0, 7, KEY_KP1), + KEY(0, 6, KEY_KP2), + KEY(0, 5, KEY_KP3), + KEY(1, 7, KEY_KP4), + KEY(1, 6, KEY_KP5), + KEY(1, 5, KEY_KP6), + KEY(2, 7, KEY_KP7), + KEY(2, 6, KEY_KP8), + KEY(2, 5, KEY_KP9), + KEY(3, 6, KEY_KP0), + KEY(3, 7, KEY_KPASTERISK), + KEY(3, 5, KEY_KPDOT), /* # key */ + KEY(7, 2, KEY_NUMLOCK), /* Mute */ + KEY(7, 1, KEY_KPMINUS), /* Recall */ + KEY(6, 1, KEY_KPPLUS), /* Redial */ + KEY(7, 6, KEY_KPSLASH), /* Handsfree */ + KEY(6, 0, KEY_ENTER), /* Video */ + + KEY(7, 4, KEY_CAMERA), /* Photo */ + + KEY(0, 4, KEY_F2), /* Home */ + KEY(1, 4, KEY_F3), /* Office */ + KEY(2, 4, KEY_F4), /* Mobile */ KEY(7, 7, KEY_F5), /* SMS */ - KEY(5, 7, KEY_F6), /* Email */ + KEY(7, 5, KEY_F6), /* Email */ /* QWERTY portion of keypad */ - KEY(4, 3, KEY_Q), + KEY(3, 4, KEY_Q), KEY(3, 3, KEY_W), - KEY(2, 3, KEY_E), - KEY(1, 3, KEY_R), - KEY(0, 3, KEY_T), - KEY(7, 4, KEY_Y), - KEY(6, 4, KEY_U), - KEY(5, 4, KEY_I), + KEY(3, 2, KEY_E), + KEY(3, 1, KEY_R), + KEY(3, 0, KEY_T), + KEY(4, 7, KEY_Y), + KEY(4, 6, KEY_U), + KEY(4, 5, KEY_I), KEY(4, 4, KEY_O), - KEY(3, 4, KEY_P), + KEY(4, 3, KEY_P), - KEY(2, 4, KEY_A), - KEY(1, 4, KEY_S), - KEY(0, 4, KEY_D), - KEY(7, 5, KEY_F), - KEY(6, 5, KEY_G), + KEY(4, 2, KEY_A), + KEY(4, 1, KEY_S), + KEY(4, 0, KEY_D), + KEY(5, 7, KEY_F), + KEY(5, 6, KEY_G), KEY(5, 5, KEY_H), - KEY(4, 5, KEY_J), - KEY(3, 5, KEY_K), - KEY(2, 5, KEY_L), + KEY(5, 4, KEY_J), + KEY(5, 3, KEY_K), + KEY(5, 2, KEY_L), - KEY(1, 5, KEY_Z), - KEY(0, 5, KEY_X), - KEY(7, 6, KEY_C), + KEY(5, 1, KEY_Z), + KEY(5, 0, KEY_X), + KEY(6, 7, KEY_C), KEY(6, 6, KEY_V), - KEY(5, 6, KEY_B), - KEY(4, 6, KEY_N), - KEY(3, 6, KEY_M), - KEY(2, 6, KEY_SPACE), + KEY(6, 5, KEY_B), + KEY(6, 4, KEY_N), + KEY(6, 3, KEY_M), + KEY(6, 2, KEY_SPACE), - KEY(0, 7, KEY_LEFTSHIFT), /* Vol up */ - KEY(3, 7, KEY_LEFTCTRL), /* Vol down */ - - 0 + KEY(7, 0, KEY_LEFTSHIFT), /* Vol up */ + KEY(7, 3, KEY_LEFTCTRL), /* Vol down */ }; void ams_delta_latch1_write(u8 mask, u8 value) @@ -189,11 +187,15 @@ static struct resource ams_delta_kp_resources[] = { }, }; +static const struct matrix_keymap_data ams_delta_keymap_data = { + .keymap = ams_delta_keymap, + .keymap_size = ARRAY_SIZE(ams_delta_keymap), +}; + static struct omap_kp_platform_data ams_delta_kp_data = { .rows = 8, .cols = 8, - .keymap = ams_delta_keymap, - .keymapsize = ARRAY_SIZE(ams_delta_keymap), + .keymap_data = &ams_delta_keymap_data, .delay = 9, }; diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c index 0c3f396328b..0efb9dbae44 100644 --- a/arch/arm/mach-omap1/board-fsample.c +++ b/arch/arm/mach-omap1/board-fsample.c @@ -69,36 +69,35 @@ #define fsample_cpld_clear(bit) \ fsample_cpld_write(0xf0 | ((bit) & 15), FSAMPLE_CPLD_SET_CLR) -static int fsample_keymap[] = { - KEY(0,0,KEY_UP), - KEY(0,1,KEY_RIGHT), - KEY(0,2,KEY_LEFT), - KEY(0,3,KEY_DOWN), - KEY(0,4,KEY_ENTER), - KEY(1,0,KEY_F10), - KEY(1,1,KEY_SEND), - KEY(1,2,KEY_END), - KEY(1,3,KEY_VOLUMEDOWN), - KEY(1,4,KEY_VOLUMEUP), - KEY(1,5,KEY_RECORD), - KEY(2,0,KEY_F9), - KEY(2,1,KEY_3), - KEY(2,2,KEY_6), - KEY(2,3,KEY_9), - KEY(2,4,KEY_KPDOT), - KEY(3,0,KEY_BACK), - KEY(3,1,KEY_2), - KEY(3,2,KEY_5), - KEY(3,3,KEY_8), - KEY(3,4,KEY_0), - KEY(3,5,KEY_KPSLASH), - KEY(4,0,KEY_HOME), - KEY(4,1,KEY_1), - KEY(4,2,KEY_4), - KEY(4,3,KEY_7), - KEY(4,4,KEY_KPASTERISK), - KEY(4,5,KEY_POWER), - 0 +static const unsigned int fsample_keymap[] = { + KEY(0, 0, KEY_UP), + KEY(1, 0, KEY_RIGHT), + KEY(2, 0, KEY_LEFT), + KEY(3, 0, KEY_DOWN), + KEY(4, 0, KEY_ENTER), + KEY(0, 1, KEY_F10), + KEY(1, 1, KEY_SEND), + KEY(2, 1, KEY_END), + KEY(3, 1, KEY_VOLUMEDOWN), + KEY(4, 1, KEY_VOLUMEUP), + KEY(5, 1, KEY_RECORD), + KEY(0, 2, KEY_F9), + KEY(1, 2, KEY_3), + KEY(2, 2, KEY_6), + KEY(3, 2, KEY_9), + KEY(4, 2, KEY_KPDOT), + KEY(0, 3, KEY_BACK), + KEY(1, 3, KEY_2), + KEY(2, 3, KEY_5), + KEY(3, 3, KEY_8), + KEY(4, 3, KEY_0), + KEY(5, 3, KEY_KPSLASH), + KEY(0, 4, KEY_HOME), + KEY(1, 4, KEY_1), + KEY(2, 4, KEY_4), + KEY(3, 4, KEY_7), + KEY(4, 4, KEY_KPASTERISK), + KEY(5, 4, KEY_POWER), }; static struct smc91x_platdata smc91x_info = { @@ -253,11 +252,15 @@ static struct resource kp_resources[] = { }, }; +static const struct matrix_keymap_data fsample_keymap_data = { + .keymap = fsample_keymap, + .keymap_size = ARRAY_SIZE(fsample_keymap), +}; + static struct omap_kp_platform_data kp_data = { .rows = 8, .cols = 8, - .keymap = fsample_keymap, - .keymapsize = ARRAY_SIZE(fsample_keymap), + .keymap_data = &fsample_keymap_data, .delay = 4, }; diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c index 082a73ca556..28b84aa9bdb 100644 --- a/arch/arm/mach-omap1/board-h2.c +++ b/arch/arm/mach-omap1/board-h2.c @@ -52,43 +52,42 @@ /* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */ #define OMAP1610_ETHR_START 0x04000300 -static int h2_keymap[] = { +static const unsigned int h2_keymap[] = { KEY(0, 0, KEY_LEFT), - KEY(0, 1, KEY_RIGHT), - KEY(0, 2, KEY_3), - KEY(0, 3, KEY_F10), - KEY(0, 4, KEY_F5), - KEY(0, 5, KEY_9), - KEY(1, 0, KEY_DOWN), + KEY(1, 0, KEY_RIGHT), + KEY(2, 0, KEY_3), + KEY(3, 0, KEY_F10), + KEY(4, 0, KEY_F5), + KEY(5, 0, KEY_9), + KEY(0, 1, KEY_DOWN), KEY(1, 1, KEY_UP), - KEY(1, 2, KEY_2), - KEY(1, 3, KEY_F9), - KEY(1, 4, KEY_F7), - KEY(1, 5, KEY_0), - KEY(2, 0, KEY_ENTER), - KEY(2, 1, KEY_6), + KEY(2, 1, KEY_2), + KEY(3, 1, KEY_F9), + KEY(4, 1, KEY_F7), + KEY(5, 1, KEY_0), + KEY(0, 2, KEY_ENTER), + KEY(1, 2, KEY_6), KEY(2, 2, KEY_1), - KEY(2, 3, KEY_F2), - KEY(2, 4, KEY_F6), - KEY(2, 5, KEY_HOME), - KEY(3, 0, KEY_8), - KEY(3, 1, KEY_5), - KEY(3, 2, KEY_F12), + KEY(3, 2, KEY_F2), + KEY(4, 2, KEY_F6), + KEY(5, 2, KEY_HOME), + KEY(0, 3, KEY_8), + KEY(1, 3, KEY_5), + KEY(2, 3, KEY_F12), KEY(3, 3, KEY_F3), - KEY(3, 4, KEY_F8), - KEY(3, 5, KEY_END), - KEY(4, 0, KEY_7), - KEY(4, 1, KEY_4), - KEY(4, 2, KEY_F11), - KEY(4, 3, KEY_F1), + KEY(4, 3, KEY_F8), + KEY(5, 3, KEY_END), + KEY(0, 4, KEY_7), + KEY(1, 4, KEY_4), + KEY(2, 4, KEY_F11), + KEY(3, 4, KEY_F1), KEY(4, 4, KEY_F4), - KEY(4, 5, KEY_ESC), - KEY(5, 0, KEY_F13), - KEY(5, 1, KEY_F14), - KEY(5, 2, KEY_F15), - KEY(5, 3, KEY_F16), - KEY(5, 4, KEY_SLEEP), - 0 + KEY(5, 4, KEY_ESC), + KEY(0, 5, KEY_F13), + KEY(1, 5, KEY_F14), + KEY(2, 5, KEY_F15), + KEY(3, 5, KEY_F16), + KEY(4, 5, KEY_SLEEP), }; static struct mtd_partition h2_nor_partitions[] = { @@ -270,14 +269,18 @@ static struct resource h2_kp_resources[] = { }, }; +static const struct matrix_keymap_data h2_keymap_data = { + .keymap = h2_keymap, + .keymap_size = ARRAY_SIZE(h2_keymap), +}; + static struct omap_kp_platform_data h2_kp_data = { .rows = 8, .cols = 8, - .keymap = h2_keymap, - .keymapsize = ARRAY_SIZE(h2_keymap), - .rep = 1, + .keymap_data = &h2_keymap_data, + .rep = true, .delay = 9, - .dbounce = 1, + .dbounce = true, }; static struct platform_device h2_kp_device = { diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c index d2cff5022fe..dbc8b8d882b 100644 --- a/arch/arm/mach-omap1/board-h3.c +++ b/arch/arm/mach-omap1/board-h3.c @@ -56,43 +56,42 @@ #define H3_TS_GPIO 48 -static int h3_keymap[] = { +static const unsigned int h3_keymap[] = { KEY(0, 0, KEY_LEFT), - KEY(0, 1, KEY_RIGHT), - KEY(0, 2, KEY_3), - KEY(0, 3, KEY_F10), - KEY(0, 4, KEY_F5), - KEY(0, 5, KEY_9), - KEY(1, 0, KEY_DOWN), + KEY(1, 0, KEY_RIGHT), + KEY(2, 0, KEY_3), + KEY(3, 0, KEY_F10), + KEY(4, 0, KEY_F5), + KEY(5, 0, KEY_9), + KEY(0, 1, KEY_DOWN), KEY(1, 1, KEY_UP), - KEY(1, 2, KEY_2), - KEY(1, 3, KEY_F9), - KEY(1, 4, KEY_F7), - KEY(1, 5, KEY_0), - KEY(2, 0, KEY_ENTER), - KEY(2, 1, KEY_6), + KEY(2, 1, KEY_2), + KEY(3, 1, KEY_F9), + KEY(4, 1, KEY_F7), + KEY(5, 1, KEY_0), + KEY(0, 2, KEY_ENTER), + KEY(1, 2, KEY_6), KEY(2, 2, KEY_1), - KEY(2, 3, KEY_F2), - KEY(2, 4, KEY_F6), - KEY(2, 5, KEY_HOME), - KEY(3, 0, KEY_8), - KEY(3, 1, KEY_5), - KEY(3, 2, KEY_F12), + KEY(3, 2, KEY_F2), + KEY(4, 2, KEY_F6), + KEY(5, 2, KEY_HOME), + KEY(0, 3, KEY_8), + KEY(1, 3, KEY_5), + KEY(2, 3, KEY_F12), KEY(3, 3, KEY_F3), - KEY(3, 4, KEY_F8), - KEY(3, 5, KEY_END), - KEY(4, 0, KEY_7), - KEY(4, 1, KEY_4), - KEY(4, 2, KEY_F11), - KEY(4, 3, KEY_F1), + KEY(4, 3, KEY_F8), + KEY(5, 3, KEY_END), + KEY(0, 4, KEY_7), + KEY(1, 4, KEY_4), + KEY(2, 4, KEY_F11), + KEY(3, 4, KEY_F1), KEY(4, 4, KEY_F4), - KEY(4, 5, KEY_ESC), - KEY(5, 0, KEY_F13), - KEY(5, 1, KEY_F14), - KEY(5, 2, KEY_F15), - KEY(5, 3, KEY_F16), - KEY(5, 4, KEY_SLEEP), - 0 + KEY(5, 4, KEY_ESC), + KEY(0, 5, KEY_F13), + KEY(1, 5, KEY_F14), + KEY(2, 5, KEY_F15), + KEY(3, 5, KEY_F16), + KEY(4, 5, KEY_SLEEP), }; @@ -305,14 +304,18 @@ static struct resource h3_kp_resources[] = { }, }; +static const struct matrix_keymap_data h3_keymap_data = { + .keymap = h3_keymap, + .keymap_size = ARRAY_SIZE(h3_keymap), +}; + static struct omap_kp_platform_data h3_kp_data = { .rows = 8, .cols = 8, - .keymap = h3_keymap, - .keymapsize = ARRAY_SIZE(h3_keymap), - .rep = 1, + .keymap_data = &h3_keymap_data, + .rep = true, .delay = 9, - .dbounce = 1, + .dbounce = true, }; static struct platform_device h3_kp_device = { diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c index 742c6d10726..f2c5c585bc8 100644 --- a/arch/arm/mach-omap1/board-htcherald.c +++ b/arch/arm/mach-omap1/board-htcherald.c @@ -180,64 +180,68 @@ /* Keyboard definition */ -static int htc_herald_keymap[] = { +static const unsigned int htc_herald_keymap[] = { KEY(0, 0, KEY_RECORD), /* Mail button */ - KEY(0, 1, KEY_CAMERA), /* Camera */ - KEY(0, 2, KEY_PHONE), /* Send key */ - KEY(0, 3, KEY_VOLUMEUP), /* Volume up */ - KEY(0, 4, KEY_F2), /* Right bar (landscape) */ - KEY(0, 5, KEY_MAIL), /* Win key (portrait) */ - KEY(0, 6, KEY_DIRECTORY), /* Right bar (protrait) */ - KEY(1, 0, KEY_LEFTCTRL), /* Windows key */ + KEY(1, 0, KEY_CAMERA), /* Camera */ + KEY(2, 0, KEY_PHONE), /* Send key */ + KEY(3, 0, KEY_VOLUMEUP), /* Volume up */ + KEY(4, 0, KEY_F2), /* Right bar (landscape) */ + KEY(5, 0, KEY_MAIL), /* Win key (portrait) */ + KEY(6, 0, KEY_DIRECTORY), /* Right bar (protrait) */ + KEY(0, 1, KEY_LEFTCTRL), /* Windows key */ KEY(1, 1, KEY_COMMA), - KEY(1, 2, KEY_M), - KEY(1, 3, KEY_K), - KEY(1, 4, KEY_SLASH), /* OK key */ - KEY(1, 5, KEY_I), - KEY(1, 6, KEY_U), - KEY(2, 0, KEY_LEFTALT), - KEY(2, 1, KEY_TAB), + KEY(2, 1, KEY_M), + KEY(3, 1, KEY_K), + KEY(4, 1, KEY_SLASH), /* OK key */ + KEY(5, 1, KEY_I), + KEY(6, 1, KEY_U), + KEY(0, 2, KEY_LEFTALT), + KEY(1, 2, KEY_TAB), KEY(2, 2, KEY_N), - KEY(2, 3, KEY_J), - KEY(2, 4, KEY_ENTER), - KEY(2, 5, KEY_H), - KEY(2, 6, KEY_Y), - KEY(3, 0, KEY_SPACE), - KEY(3, 1, KEY_L), - KEY(3, 2, KEY_B), + KEY(3, 2, KEY_J), + KEY(4, 2, KEY_ENTER), + KEY(5, 2, KEY_H), + KEY(6, 2, KEY_Y), + KEY(0, 3, KEY_SPACE), + KEY(1, 3, KEY_L), + KEY(2, 3, KEY_B), KEY(3, 3, KEY_V), - KEY(3, 4, KEY_BACKSPACE), - KEY(3, 5, KEY_G), - KEY(3, 6, KEY_T), - KEY(4, 0, KEY_CAPSLOCK), /* Shift */ - KEY(4, 1, KEY_C), - KEY(4, 2, KEY_F), - KEY(4, 3, KEY_R), + KEY(4, 3, KEY_BACKSPACE), + KEY(5, 3, KEY_G), + KEY(6, 3, KEY_T), + KEY(0, 4, KEY_CAPSLOCK), /* Shift */ + KEY(1, 4, KEY_C), + KEY(2, 4, KEY_F), + KEY(3, 4, KEY_R), KEY(4, 4, KEY_O), - KEY(4, 5, KEY_E), - KEY(4, 6, KEY_D), - KEY(5, 0, KEY_X), - KEY(5, 1, KEY_Z), - KEY(5, 2, KEY_S), - KEY(5, 3, KEY_W), - KEY(5, 4, KEY_P), + KEY(5, 4, KEY_E), + KEY(6, 4, KEY_D), + KEY(0, 5, KEY_X), + KEY(1, 5, KEY_Z), + KEY(2, 5, KEY_S), + KEY(3, 5, KEY_W), + KEY(4, 5, KEY_P), KEY(5, 5, KEY_Q), - KEY(5, 6, KEY_A), - KEY(6, 0, KEY_CONNECT), /* Voice button */ - KEY(6, 2, KEY_CANCEL), /* End key */ - KEY(6, 3, KEY_VOLUMEDOWN), /* Volume down */ - KEY(6, 4, KEY_F1), /* Left bar (landscape) */ - KEY(6, 5, KEY_WWW), /* OK button (portrait) */ + KEY(6, 5, KEY_A), + KEY(0, 6, KEY_CONNECT), /* Voice button */ + KEY(2, 6, KEY_CANCEL), /* End key */ + KEY(3, 6, KEY_VOLUMEDOWN), /* Volume down */ + KEY(4, 6, KEY_F1), /* Left bar (landscape) */ + KEY(5, 6, KEY_WWW), /* OK button (portrait) */ KEY(6, 6, KEY_CALENDAR), /* Left bar (portrait) */ - 0 }; -struct omap_kp_platform_data htcherald_kp_data = { +static const struct matrix_keymap_data htc_herald_keymap_data = { + .keymap = htc_herald_keymap, + .keymap_size = ARRAY_SIZE(htc_herald_keymap), +}; + +static struct omap_kp_platform_data htcherald_kp_data = { .rows = 7, .cols = 7, .delay = 20, - .rep = 1, - .keymap = htc_herald_keymap, + .rep = true, + .keymap_data = &htc_herald_keymap_data, }; static struct resource kp_resources[] = { @@ -278,7 +282,7 @@ static struct gpio_keys_button herald_gpio_keys_table[] = { static struct gpio_keys_platform_data herald_gpio_keys_data = { .buttons = herald_gpio_keys_table, .nbuttons = ARRAY_SIZE(herald_gpio_keys_table), - .rep = 1, + .rep = true, }; static struct platform_device herald_gpiokeys_device = { diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c index 8d59b078fc2..a36e6742bf9 100644 --- a/arch/arm/mach-omap1/board-innovator.c +++ b/arch/arm/mach-omap1/board-innovator.c @@ -44,17 +44,16 @@ /* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */ #define INNOVATOR1610_ETHR_START 0x04000300 -static int innovator_keymap[] = { +static const unsigned int innovator_keymap[] = { KEY(0, 0, KEY_F1), - KEY(0, 3, KEY_DOWN), + KEY(3, 0, KEY_DOWN), KEY(1, 1, KEY_F2), - KEY(1, 2, KEY_RIGHT), - KEY(2, 0, KEY_F3), - KEY(2, 1, KEY_F4), + KEY(2, 1, KEY_RIGHT), + KEY(0, 2, KEY_F3), + KEY(1, 2, KEY_F4), KEY(2, 2, KEY_UP), - KEY(3, 2, KEY_ENTER), + KEY(2, 3, KEY_ENTER), KEY(3, 3, KEY_LEFT), - 0 }; static struct mtd_partition innovator_partitions[] = { @@ -126,11 +125,15 @@ static struct resource innovator_kp_resources[] = { }, }; +static const struct matrix_keymap_data innovator_keymap_data = { + .keymap = innovator_keymap, + .keymap_size = ARRAY_SIZE(innovator_keymap), +}; + static struct omap_kp_platform_data innovator_kp_data = { .rows = 8, .cols = 8, - .keymap = innovator_keymap, - .keymapsize = ARRAY_SIZE(innovator_keymap), + .keymap_data = &innovator_keymap_data, .delay = 4, }; diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c index 605495bbc58..d21f09dc78f 100644 --- a/arch/arm/mach-omap1/board-nokia770.c +++ b/arch/arm/mach-omap1/board-nokia770.c @@ -54,19 +54,18 @@ static void __init omap_nokia770_init_irq(void) omap_init_irq(); } -static int nokia770_keymap[] = { - KEY(0, 1, GROUP_0 | KEY_UP), - KEY(0, 2, GROUP_1 | KEY_F5), - KEY(1, 0, GROUP_0 | KEY_LEFT), +static const unsigned int nokia770_keymap[] = { + KEY(1, 0, GROUP_0 | KEY_UP), + KEY(2, 0, GROUP_1 | KEY_F5), + KEY(0, 1, GROUP_0 | KEY_LEFT), KEY(1, 1, GROUP_0 | KEY_ENTER), - KEY(1, 2, GROUP_0 | KEY_RIGHT), - KEY(2, 0, GROUP_1 | KEY_ESC), - KEY(2, 1, GROUP_0 | KEY_DOWN), + KEY(2, 1, GROUP_0 | KEY_RIGHT), + KEY(0, 2, GROUP_1 | KEY_ESC), + KEY(1, 2, GROUP_0 | KEY_DOWN), KEY(2, 2, GROUP_1 | KEY_F4), - KEY(3, 0, GROUP_2 | KEY_F7), - KEY(3, 1, GROUP_2 | KEY_F8), - KEY(3, 2, GROUP_2 | KEY_F6), - 0 + KEY(0, 3, GROUP_2 | KEY_F7), + KEY(1, 3, GROUP_2 | KEY_F8), + KEY(2, 3, GROUP_2 | KEY_F6), }; static struct resource nokia770_kp_resources[] = { @@ -77,11 +76,15 @@ static struct resource nokia770_kp_resources[] = { }, }; +static const struct matrix_keymap_data nokia770_keymap_data = { + .keymap = nokia770_keymap, + .keymap_size = ARRAY_SIZE(nokia770_keymap), +}; + static struct omap_kp_platform_data nokia770_kp_data = { .rows = 8, .cols = 8, - .keymap = nokia770_keymap, - .keymapsize = ARRAY_SIZE(nokia770_keymap), + .keymap_data = &nokia770_keymap_data, .delay = 4, }; diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c index d44e7172efc..7c5e2112c77 100644 --- a/arch/arm/mach-omap1/board-osk.c +++ b/arch/arm/mach-omap1/board-osk.c @@ -338,25 +338,28 @@ static struct i2c_board_info __initdata mistral_i2c_board_info[] = { */ }; -static const int osk_keymap[] = { +static const unsigned int osk_keymap[] = { /* KEY(col, row, code) */ KEY(0, 0, KEY_F1), /* SW4 */ - KEY(0, 3, KEY_UP), /* (sw2/up) */ + KEY(3, 0, KEY_UP), /* (sw2/up) */ KEY(1, 1, KEY_LEFTCTRL), /* SW5 */ - KEY(1, 2, KEY_LEFT), /* (sw2/left) */ - KEY(2, 0, KEY_SPACE), /* SW3 */ - KEY(2, 1, KEY_ESC), /* SW6 */ + KEY(2, 1, KEY_LEFT), /* (sw2/left) */ + KEY(0, 2, KEY_SPACE), /* SW3 */ + KEY(1, 2, KEY_ESC), /* SW6 */ KEY(2, 2, KEY_DOWN), /* (sw2/down) */ - KEY(3, 2, KEY_ENTER), /* (sw2/select) */ + KEY(2, 3, KEY_ENTER), /* (sw2/select) */ KEY(3, 3, KEY_RIGHT), /* (sw2/right) */ - 0 +}; + +static const struct matrix_keymap_data osk_keymap_data = { + .keymap = osk_keymap, + .keymap_size = ARRAY_SIZE(osk_keymap), }; static struct omap_kp_platform_data osk_kp_data = { .rows = 8, .cols = 8, - .keymap = (int *) osk_keymap, - .keymapsize = ARRAY_SIZE(osk_keymap), + .keymap_data = &osk_keymap_data, .delay = 9, }; diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c index 994dc6f5072..fb51ce6123d 100644 --- a/arch/arm/mach-omap1/board-palmte.c +++ b/arch/arm/mach-omap1/board-palmte.c @@ -65,25 +65,29 @@ static void __init omap_palmte_init_irq(void) omap_init_irq(); } -static const int palmte_keymap[] = { +static const unsigned int palmte_keymap[] = { KEY(0, 0, KEY_F1), /* Calendar */ - KEY(0, 1, KEY_F2), /* Contacts */ - KEY(0, 2, KEY_F3), /* Tasks List */ - KEY(0, 3, KEY_F4), /* Note Pad */ - KEY(0, 4, KEY_POWER), - KEY(1, 0, KEY_LEFT), + KEY(1, 0, KEY_F2), /* Contacts */ + KEY(2, 0, KEY_F3), /* Tasks List */ + KEY(3, 0, KEY_F4), /* Note Pad */ + KEY(4, 0, KEY_POWER), + KEY(0, 1, KEY_LEFT), KEY(1, 1, KEY_DOWN), - KEY(1, 2, KEY_UP), - KEY(1, 3, KEY_RIGHT), - KEY(1, 4, KEY_ENTER), - 0, + KEY(2, 1, KEY_UP), + KEY(3, 1, KEY_RIGHT), + KEY(4, 1, KEY_ENTER), +}; + +static const struct matrix_keymap_data palmte_keymap_data = { + .keymap = palmte_keymap, + .keymap_size = ARRAY_SIZE(palmte_keymap), }; static struct omap_kp_platform_data palmte_kp_data = { .rows = 8, .cols = 8, - .keymap = (int *) palmte_keymap, - .rep = 1, + .keymap_data = &palmte_keymap_data, + .rep = true, .delay = 12, }; diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c index ed1400a67f7..f04f2d36e7d 100644 --- a/arch/arm/mach-omap1/board-palmtt.c +++ b/arch/arm/mach-omap1/board-palmtt.c @@ -51,19 +51,18 @@ #define PALMTT_MMC_WP_GPIO 8 #define PALMTT_HDQ_GPIO 11 -static int palmtt_keymap[] = { +static const unsigned int palmtt_keymap[] = { KEY(0, 0, KEY_ESC), - KEY(0, 1, KEY_SPACE), - KEY(0, 2, KEY_LEFTCTRL), - KEY(0, 3, KEY_TAB), - KEY(0, 4, KEY_ENTER), - KEY(1, 0, KEY_LEFT), + KEY(1, 0, KEY_SPACE), + KEY(2, 0, KEY_LEFTCTRL), + KEY(3, 0, KEY_TAB), + KEY(4, 0, KEY_ENTER), + KEY(0, 1, KEY_LEFT), KEY(1, 1, KEY_DOWN), - KEY(1, 2, KEY_UP), - KEY(1, 3, KEY_RIGHT), - KEY(2, 0, KEY_SLEEP), - KEY(2, 4, KEY_Y), - 0 + KEY(2, 1, KEY_UP), + KEY(3, 1, KEY_RIGHT), + KEY(0, 2, KEY_SLEEP), + KEY(4, 2, KEY_Y), }; static struct mtd_partition palmtt_partitions[] = { @@ -136,10 +135,15 @@ static struct resource palmtt_kp_resources[] = { }, }; +static const struct matrix_keymap_data palmtt_keymap_data = { + .keymap = palmtt_keymap, + .keymap_size = ARRAY_SIZE(palmtt_keymap), +}; + static struct omap_kp_platform_data palmtt_kp_data = { .rows = 6, .cols = 3, - .keymap = palmtt_keymap, + .keymap_data = &palmtt_keymap_data, }; static struct platform_device palmtt_kp_device = { diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c index 2afac598bae..d7bbbe721a7 100644 --- a/arch/arm/mach-omap1/board-palmz71.c +++ b/arch/arm/mach-omap1/board-palmz71.c @@ -64,26 +64,30 @@ omap_palmz71_init_irq(void) omap_init_irq(); } -static int palmz71_keymap[] = { +static const unsigned int palmz71_keymap[] = { KEY(0, 0, KEY_F1), - KEY(0, 1, KEY_F2), - KEY(0, 2, KEY_F3), - KEY(0, 3, KEY_F4), - KEY(0, 4, KEY_POWER), - KEY(1, 0, KEY_LEFT), + KEY(1, 0, KEY_F2), + KEY(2, 0, KEY_F3), + KEY(3, 0, KEY_F4), + KEY(4, 0, KEY_POWER), + KEY(0, 1, KEY_LEFT), KEY(1, 1, KEY_DOWN), - KEY(1, 2, KEY_UP), - KEY(1, 3, KEY_RIGHT), - KEY(1, 4, KEY_ENTER), - KEY(2, 0, KEY_CAMERA), - 0, + KEY(2, 1, KEY_UP), + KEY(3, 1, KEY_RIGHT), + KEY(4, 1, KEY_ENTER), + KEY(0, 2, KEY_CAMERA), +}; + +static const struct matrix_keymap_data palmz71_keymap_data = { + .keymap = palmz71_keymap, + .keymap_size = ARRAY_SIZE(palmz71_keymap), }; static struct omap_kp_platform_data palmz71_kp_data = { .rows = 8, .cols = 8, - .keymap = palmz71_keymap, - .rep = 1, + .keymap_data = &palmz71_keymap_data, + .rep = true, .delay = 80, }; diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c index 69fda218fb4..3c8ee848945 100644 --- a/arch/arm/mach-omap1/board-perseus2.c +++ b/arch/arm/mach-omap1/board-perseus2.c @@ -36,36 +36,35 @@ #include <plat/common.h> #include <plat/board.h> -static int p2_keymap[] = { - KEY(0,0,KEY_UP), - KEY(0,1,KEY_RIGHT), - KEY(0,2,KEY_LEFT), - KEY(0,3,KEY_DOWN), - KEY(0,4,KEY_ENTER), - KEY(1,0,KEY_F10), - KEY(1,1,KEY_SEND), - KEY(1,2,KEY_END), - KEY(1,3,KEY_VOLUMEDOWN), - KEY(1,4,KEY_VOLUMEUP), - KEY(1,5,KEY_RECORD), - KEY(2,0,KEY_F9), - KEY(2,1,KEY_3), - KEY(2,2,KEY_6), - KEY(2,3,KEY_9), - KEY(2,4,KEY_KPDOT), - KEY(3,0,KEY_BACK), - KEY(3,1,KEY_2), - KEY(3,2,KEY_5), - KEY(3,3,KEY_8), - KEY(3,4,KEY_0), - KEY(3,5,KEY_KPSLASH), - KEY(4,0,KEY_HOME), - KEY(4,1,KEY_1), - KEY(4,2,KEY_4), - KEY(4,3,KEY_7), - KEY(4,4,KEY_KPASTERISK), - KEY(4,5,KEY_POWER), - 0 +static const unsigned int p2_keymap[] = { + KEY(0, 0, KEY_UP), + KEY(1, 0, KEY_RIGHT), + KEY(2, 0, KEY_LEFT), + KEY(3, 0, KEY_DOWN), + KEY(4, 0, KEY_ENTER), + KEY(0, 1, KEY_F10), + KEY(1, 1, KEY_SEND), + KEY(2, 1, KEY_END), + KEY(3, 1, KEY_VOLUMEDOWN), + KEY(4, 1, KEY_VOLUMEUP), + KEY(5, 1, KEY_RECORD), + KEY(0, 2, KEY_F9), + KEY(1, 2, KEY_3), + KEY(2, 2, KEY_6), + KEY(3, 2, KEY_9), + KEY(4, 2, KEY_KPDOT), + KEY(0, 3, KEY_BACK), + KEY(1, 3, KEY_2), + KEY(2, 3, KEY_5), + KEY(3, 3, KEY_8), + KEY(4, 3, KEY_0), + KEY(5, 3, KEY_KPSLASH), + KEY(0, 4, KEY_HOME), + KEY(1, 4, KEY_1), + KEY(2, 4, KEY_4), + KEY(3, 4, KEY_7), + KEY(4, 4, KEY_KPASTERISK), + KEY(5, 4, KEY_POWER), }; static struct smc91x_platdata smc91x_info = { @@ -211,13 +210,17 @@ static struct resource kp_resources[] = { }, }; +static const struct matrix_keymap_data p2_keymap_data = { + .keymap = p2_keymap, + .keymap_size = ARRAY_SIZE(p2_keymap), +}; + static struct omap_kp_platform_data kp_data = { .rows = 8, .cols = 8, - .keymap = p2_keymap, - .keymapsize = ARRAY_SIZE(p2_keymap), + .keymap_data = &p2_keymap_data, .delay = 4, - .dbounce = 1, + .dbounce = true, }; static struct platform_device kp_device = { diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c index 463862c6781..d41fe2d0616 100644 --- a/arch/arm/mach-omap1/board-sx1.c +++ b/arch/arm/mach-omap1/board-sx1.c @@ -164,36 +164,35 @@ EXPORT_SYMBOL(sx1_setusbpower); /*----------- Keypad -------------------------*/ -static int sx1_keymap[] = { - KEY(5, 3, GROUP_0 | 117), /* camera Qt::Key_F17 */ - KEY(0, 4, GROUP_0 | 114), /* voice memo Qt::Key_F14 */ - KEY(1, 4, GROUP_2 | 114), /* voice memo */ - KEY(2, 4, GROUP_3 | 114), /* voice memo */ +static const unsigned int sx1_keymap[] = { + KEY(3, 5, GROUP_0 | 117), /* camera Qt::Key_F17 */ + KEY(4, 0, GROUP_0 | 114), /* voice memo Qt::Key_F14 */ + KEY(4, 1, GROUP_2 | 114), /* voice memo */ + KEY(4, 2, GROUP_3 | 114), /* voice memo */ KEY(0, 0, GROUP_1 | KEY_F12), /* red button Qt::Key_Hangup */ - KEY(4, 3, GROUP_1 | KEY_LEFT), - KEY(2, 3, GROUP_1 | KEY_DOWN), - KEY(1, 3, GROUP_1 | KEY_RIGHT), - KEY(0, 3, GROUP_1 | KEY_UP), + KEY(3, 4, GROUP_1 | KEY_LEFT), + KEY(3, 2, GROUP_1 | KEY_DOWN), + KEY(3, 1, GROUP_1 | KEY_RIGHT), + KEY(3, 0, GROUP_1 | KEY_UP), KEY(3, 3, GROUP_1 | KEY_POWER), /* joystick press or Qt::Key_Select */ - KEY(5, 0, GROUP_1 | KEY_1), - KEY(4, 0, GROUP_1 | KEY_2), - KEY(3, 0, GROUP_1 | KEY_3), - KEY(3, 4, GROUP_1 | KEY_4), + KEY(0, 5, GROUP_1 | KEY_1), + KEY(0, 4, GROUP_1 | KEY_2), + KEY(0, 3, GROUP_1 | KEY_3), + KEY(4, 3, GROUP_1 | KEY_4), KEY(4, 4, GROUP_1 | KEY_5), - KEY(5, 4, GROUP_1 | KEY_KPASTERISK),/* "*" */ - KEY(4, 1, GROUP_1 | KEY_6), - KEY(5, 1, GROUP_1 | KEY_7), - KEY(3, 1, GROUP_1 | KEY_8), - KEY(3, 2, GROUP_1 | KEY_9), - KEY(5, 2, GROUP_1 | KEY_0), - KEY(4, 2, GROUP_1 | 113), /* # F13 Toggle input method Qt::Key_F13 */ - KEY(0, 1, GROUP_1 | KEY_F11), /* green button Qt::Key_Call */ - KEY(1, 2, GROUP_1 | KEY_YEN), /* left soft Qt::Key_Context1 */ + KEY(4, 5, GROUP_1 | KEY_KPASTERISK),/* "*" */ + KEY(1, 4, GROUP_1 | KEY_6), + KEY(1, 5, GROUP_1 | KEY_7), + KEY(1, 3, GROUP_1 | KEY_8), + KEY(2, 3, GROUP_1 | KEY_9), + KEY(2, 5, GROUP_1 | KEY_0), + KEY(2, 4, GROUP_1 | 113), /* # F13 Toggle input method Qt::Key_F13 */ + KEY(1, 0, GROUP_1 | KEY_F11), /* green button Qt::Key_Call */ + KEY(2, 1, GROUP_1 | KEY_YEN), /* left soft Qt::Key_Context1 */ KEY(2, 2, GROUP_1 | KEY_F8), /* right soft Qt::Key_Back */ - KEY(2, 1, GROUP_1 | KEY_LEFTSHIFT), /* shift */ + KEY(1, 2, GROUP_1 | KEY_LEFTSHIFT), /* shift */ KEY(1, 1, GROUP_1 | KEY_BACKSPACE), /* C (clear) */ - KEY(0, 2, GROUP_1 | KEY_F7), /* menu Qt::Key_Menu */ - 0 + KEY(2, 0, GROUP_1 | KEY_F7), /* menu Qt::Key_Menu */ }; static struct resource sx1_kp_resources[] = { @@ -204,11 +203,15 @@ static struct resource sx1_kp_resources[] = { }, }; +static const struct matrix_keymap_data sx1_keymap_data = { + .keymap = sx1_keymap, + .keymap_size = ARRAY_SIZE(sx1_keymap), +}; + static struct omap_kp_platform_data sx1_kp_data = { .rows = 6, .cols = 6, - .keymap = sx1_keymap, - .keymapsize = ARRAY_SIZE(sx1_keymap), + .keymap_data = &sx1_keymap_data, .delay = 80, }; diff --git a/arch/arm/mach-omap1/dma.c b/arch/arm/mach-omap1/dma.c new file mode 100644 index 00000000000..d8559344c6e --- /dev/null +++ b/arch/arm/mach-omap1/dma.c @@ -0,0 +1,390 @@ +/* + * OMAP1/OMAP7xx - specific DMA driver + * + * Copyright (C) 2003 - 2008 Nokia Corporation + * Author: Juha Yrjölä <juha.yrjola@nokia.com> + * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com> + * Graphics DMA and LCD DMA graphics tranformations + * by Imre Deak <imre.deak@nokia.com> + * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc. + * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc. + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * Converted DMA library into platform driver + * - G, Manjunath Kondaiah <manjugk@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/err.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/device.h> + +#include <plat/dma.h> +#include <plat/tc.h> +#include <plat/irqs.h> + +#define OMAP1_DMA_BASE (0xfffed800) +#define OMAP1_LOGICAL_DMA_CH_COUNT 17 +#define OMAP1_DMA_STRIDE 0x40 + +static u32 errata; +static u32 enable_1510_mode; +static u8 dma_stride; +static enum omap_reg_offsets dma_common_ch_start, dma_common_ch_end; + +static u16 reg_map[] = { + [GCR] = 0x400, + [GSCR] = 0x404, + [GRST1] = 0x408, + [HW_ID] = 0x442, + [PCH2_ID] = 0x444, + [PCH0_ID] = 0x446, + [PCH1_ID] = 0x448, + [PCHG_ID] = 0x44a, + [PCHD_ID] = 0x44c, + [CAPS_0] = 0x44e, + [CAPS_1] = 0x452, + [CAPS_2] = 0x456, + [CAPS_3] = 0x458, + [CAPS_4] = 0x45a, + [PCH2_SR] = 0x460, + [PCH0_SR] = 0x480, + [PCH1_SR] = 0x482, + [PCHD_SR] = 0x4c0, + + /* Common Registers */ + [CSDP] = 0x00, + [CCR] = 0x02, + [CICR] = 0x04, + [CSR] = 0x06, + [CEN] = 0x10, + [CFN] = 0x12, + [CSFI] = 0x14, + [CSEI] = 0x16, + [CPC] = 0x18, /* 15xx only */ + [CSAC] = 0x18, + [CDAC] = 0x1a, + [CDEI] = 0x1c, + [CDFI] = 0x1e, + [CLNK_CTRL] = 0x28, + + /* Channel specific register offsets */ + [CSSA] = 0x08, + [CDSA] = 0x0c, + [COLOR] = 0x20, + [CCR2] = 0x24, + [LCH_CTRL] = 0x2a, +}; + +static struct resource res[] __initdata = { + [0] = { + .start = OMAP1_DMA_BASE, + .end = OMAP1_DMA_BASE + SZ_2K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .name = "0", + .start = INT_DMA_CH0_6, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .name = "1", + .start = INT_DMA_CH1_7, + .flags = IORESOURCE_IRQ, + }, + [3] = { + .name = "2", + .start = INT_DMA_CH2_8, + .flags = IORESOURCE_IRQ, + }, + [4] = { + .name = "3", + .start = INT_DMA_CH3, + .flags = IORESOURCE_IRQ, + }, + [5] = { + .name = "4", + .start = INT_DMA_CH4, + .flags = IORESOURCE_IRQ, + }, + [6] = { + .name = "5", + .start = INT_DMA_CH5, + .flags = IORESOURCE_IRQ, + }, + /* Handled in lcd_dma.c */ + [7] = { + .name = "6", + .start = INT_1610_DMA_CH6, + .flags = IORESOURCE_IRQ, + }, + /* irq's for omap16xx and omap7xx */ + [8] = { + .name = "7", + .start = INT_1610_DMA_CH7, + .flags = IORESOURCE_IRQ, + }, + [9] = { + .name = "8", + .start = INT_1610_DMA_CH8, + .flags = IORESOURCE_IRQ, + }, + [10] = { + .name = "9", + .start = INT_1610_DMA_CH9, + .flags = IORESOURCE_IRQ, + }, + [11] = { + .name = "10", + .start = INT_1610_DMA_CH10, + .flags = IORESOURCE_IRQ, + }, + [12] = { + .name = "11", + .start = INT_1610_DMA_CH11, + .flags = IORESOURCE_IRQ, + }, + [13] = { + .name = "12", + .start = INT_1610_DMA_CH12, + .flags = IORESOURCE_IRQ, + }, + [14] = { + .name = "13", + .start = INT_1610_DMA_CH13, + .flags = IORESOURCE_IRQ, + }, + [15] = { + .name = "14", + .start = INT_1610_DMA_CH14, + .flags = IORESOURCE_IRQ, + }, + [16] = { + .name = "15", + .start = INT_1610_DMA_CH15, + .flags = IORESOURCE_IRQ, + }, + [17] = { + .name = "16", + .start = INT_DMA_LCD, + .flags = IORESOURCE_IRQ, + }, +}; + +static void __iomem *dma_base; +static inline void dma_write(u32 val, int reg, int lch) +{ + u8 stride; + u32 offset; + + stride = (reg >= dma_common_ch_start) ? dma_stride : 0; + offset = reg_map[reg] + (stride * lch); + + __raw_writew(val, dma_base + offset); + if ((reg > CLNK_CTRL && reg < CCEN) || + (reg > PCHD_ID && reg < CAPS_2)) { + u32 offset2 = reg_map[reg] + 2 + (stride * lch); + __raw_writew(val >> 16, dma_base + offset2); + } +} + +static inline u32 dma_read(int reg, int lch) +{ + u8 stride; + u32 offset, val; + + stride = (reg >= dma_common_ch_start) ? dma_stride : 0; + offset = reg_map[reg] + (stride * lch); + + val = __raw_readw(dma_base + offset); + if ((reg > CLNK_CTRL && reg < CCEN) || + (reg > PCHD_ID && reg < CAPS_2)) { + u16 upper; + u32 offset2 = reg_map[reg] + 2 + (stride * lch); + upper = __raw_readw(dma_base + offset2); + val |= (upper << 16); + } + return val; +} + +static void omap1_clear_lch_regs(int lch) +{ + int i = dma_common_ch_start; + + for (; i <= dma_common_ch_end; i += 1) + dma_write(0, i, lch); +} + +static void omap1_clear_dma(int lch) +{ + u32 l; + + l = dma_read(CCR, lch); + l &= ~OMAP_DMA_CCR_EN; + dma_write(l, CCR, lch); + + /* Clear pending interrupts */ + l = dma_read(CSR, lch); +} + +static void omap1_show_dma_caps(void) +{ + if (enable_1510_mode) { + printk(KERN_INFO "DMA support for OMAP15xx initialized\n"); + } else { + u16 w; + printk(KERN_INFO "OMAP DMA hardware version %d\n", + dma_read(HW_ID, 0)); + printk(KERN_INFO "DMA capabilities: %08x:%08x:%04x:%04x:%04x\n", + dma_read(CAPS_0, 0), dma_read(CAPS_1, 0), + dma_read(CAPS_2, 0), dma_read(CAPS_3, 0), + dma_read(CAPS_4, 0)); + + /* Disable OMAP 3.0/3.1 compatibility mode. */ + w = dma_read(GSCR, 0); + w |= 1 << 3; + dma_write(w, GSCR, 0); + } + return; +} + +static u32 configure_dma_errata(void) +{ + + /* + * Erratum 3.2/3.3: sometimes 0 is returned if CSAC/CDAC is + * read before the DMA controller finished disabling the channel. + */ + if (!cpu_is_omap15xx()) + SET_DMA_ERRATA(DMA_ERRATA_3_3); + + return errata; +} + +static int __init omap1_system_dma_init(void) +{ + struct omap_system_dma_plat_info *p; + struct omap_dma_dev_attr *d; + struct platform_device *pdev; + int ret; + + pdev = platform_device_alloc("omap_dma_system", 0); + if (!pdev) { + pr_err("%s: Unable to device alloc for dma\n", + __func__); + return -ENOMEM; + } + + dma_base = ioremap(res[0].start, resource_size(&res[0])); + if (!dma_base) { + pr_err("%s: Unable to ioremap\n", __func__); + return -ENODEV; + } + + ret = platform_device_add_resources(pdev, res, ARRAY_SIZE(res)); + if (ret) { + dev_err(&pdev->dev, "%s: Unable to add resources for %s%d\n", + __func__, pdev->name, pdev->id); + goto exit_device_del; + } + + p = kzalloc(sizeof(struct omap_system_dma_plat_info), GFP_KERNEL); + if (!p) { + dev_err(&pdev->dev, "%s: Unable to allocate 'p' for %s\n", + __func__, pdev->name); + ret = -ENOMEM; + goto exit_device_put; + } + + d = kzalloc(sizeof(struct omap_dma_dev_attr), GFP_KERNEL); + if (!d) { + dev_err(&pdev->dev, "%s: Unable to allocate 'd' for %s\n", + __func__, pdev->name); + ret = -ENOMEM; + goto exit_release_p; + } + + d->lch_count = OMAP1_LOGICAL_DMA_CH_COUNT; + + /* Valid attributes for omap1 plus processors */ + if (cpu_is_omap15xx()) + d->dev_caps = ENABLE_1510_MODE; + enable_1510_mode = d->dev_caps & ENABLE_1510_MODE; + + d->dev_caps |= SRC_PORT; + d->dev_caps |= DST_PORT; + d->dev_caps |= SRC_INDEX; + d->dev_caps |= DST_INDEX; + d->dev_caps |= IS_BURST_ONLY4; + d->dev_caps |= CLEAR_CSR_ON_READ; + d->dev_caps |= IS_WORD_16; + + + d->chan = kzalloc(sizeof(struct omap_dma_lch) * + (d->lch_count), GFP_KERNEL); + if (!d->chan) { + dev_err(&pdev->dev, "%s: Memory allocation failed" + "for d->chan!!!\n", __func__); + goto exit_release_d; + } + + if (cpu_is_omap15xx()) + d->chan_count = 9; + else if (cpu_is_omap16xx() || cpu_is_omap7xx()) { + if (!(d->dev_caps & ENABLE_1510_MODE)) + d->chan_count = 16; + else + d->chan_count = 9; + } + + p->dma_attr = d; + + p->show_dma_caps = omap1_show_dma_caps; + p->clear_lch_regs = omap1_clear_lch_regs; + p->clear_dma = omap1_clear_dma; + p->dma_write = dma_write; + p->dma_read = dma_read; + p->disable_irq_lch = NULL; + + p->errata = configure_dma_errata(); + + ret = platform_device_add_data(pdev, p, sizeof(*p)); + if (ret) { + dev_err(&pdev->dev, "%s: Unable to add resources for %s%d\n", + __func__, pdev->name, pdev->id); + goto exit_release_chan; + } + + ret = platform_device_add(pdev); + if (ret) { + dev_err(&pdev->dev, "%s: Unable to add resources for %s%d\n", + __func__, pdev->name, pdev->id); + goto exit_release_chan; + } + + dma_stride = OMAP1_DMA_STRIDE; + dma_common_ch_start = CPC; + dma_common_ch_end = COLOR; + + return ret; + +exit_release_chan: + kfree(d->chan); +exit_release_d: + kfree(d); +exit_release_p: + kfree(p); +exit_device_put: + platform_device_put(pdev); +exit_device_del: + platform_device_del(pdev); + + return ret; +} +arch_initcall(omap1_system_dma_init); diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 92b004ba5a1..3e8c9e859f9 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -35,6 +35,8 @@ config ARCH_OMAP3 select CPU_V7 select USB_ARCH_HAS_EHCI select ARM_L1_CACHE_SHIFT_6 if !ARCH_OMAP4 + select ARCH_HAS_OPP + select PM_OPP if PM config ARCH_OMAP4 bool "TI OMAP4" @@ -44,6 +46,8 @@ config ARCH_OMAP4 select ARM_GIC select PL310_ERRATA_588369 select ARM_ERRATA_720789 + select ARCH_HAS_OPP + select PM_OPP if PM comment "OMAP Core Type" depends on ARCH_OMAP2 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index b86b0629238..1b699d3c6cb 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -4,7 +4,7 @@ # Common support obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer-gp.o pm.o \ - common.o gpio.o + common.o gpio.o dma.o omap-2-3-common = irq.o sdrc.o prm2xxx_3xxx.o hwmod-common = omap_hwmod.o \ @@ -49,6 +49,13 @@ obj-$(CONFIG_ARCH_OMAP4) += mux44xx.o obj-$(CONFIG_ARCH_OMAP2) += sdrc2xxx.o # obj-$(CONFIG_ARCH_OMAP3) += sdrc3xxx.o +# OPP table initialization +ifeq ($(CONFIG_PM_OPP),y) +obj-y += opp.o +obj-$(CONFIG_ARCH_OMAP3) += opp3xxx_data.o +obj-$(CONFIG_ARCH_OMAP4) += opp4xxx_data.o +endif + # Power Management ifeq ($(CONFIG_PM),y) obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c index a30a7fce8cb..7392c67ce10 100644 --- a/arch/arm/mach-omap2/board-devkit8000.c +++ b/arch/arm/mach-omap2/board-devkit8000.c @@ -118,27 +118,27 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev) twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0); if (gpio_is_valid(dssdev->reset_gpio)) - gpio_set_value(dssdev->reset_gpio, 1); + gpio_set_value_cansleep(dssdev->reset_gpio, 1); return 0; } static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev) { if (gpio_is_valid(dssdev->reset_gpio)) - gpio_set_value(dssdev->reset_gpio, 0); + gpio_set_value_cansleep(dssdev->reset_gpio, 0); } static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev) { if (gpio_is_valid(dssdev->reset_gpio)) - gpio_set_value(dssdev->reset_gpio, 1); + gpio_set_value_cansleep(dssdev->reset_gpio, 1); return 0; } static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev) { if (gpio_is_valid(dssdev->reset_gpio)) - gpio_set_value(dssdev->reset_gpio, 0); + gpio_set_value_cansleep(dssdev->reset_gpio, 0); } static struct regulator_consumer_supply devkit8000_vmmc1_supply = diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index 0a2d73cf036..b386a403c37 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -51,38 +51,37 @@ static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 }; static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 }; -static int h4_keymap[] = { +static const unsigned int h4_keymap[] = { KEY(0, 0, KEY_LEFT), - KEY(0, 1, KEY_RIGHT), - KEY(0, 2, KEY_A), - KEY(0, 3, KEY_B), - KEY(0, 4, KEY_C), - KEY(1, 0, KEY_DOWN), + KEY(1, 0, KEY_RIGHT), + KEY(2, 0, KEY_A), + KEY(3, 0, KEY_B), + KEY(4, 0, KEY_C), + KEY(0, 1, KEY_DOWN), KEY(1, 1, KEY_UP), - KEY(1, 2, KEY_E), - KEY(1, 3, KEY_F), - KEY(1, 4, KEY_G), - KEY(2, 0, KEY_ENTER), - KEY(2, 1, KEY_I), + KEY(2, 1, KEY_E), + KEY(3, 1, KEY_F), + KEY(4, 1, KEY_G), + KEY(0, 2, KEY_ENTER), + KEY(1, 2, KEY_I), KEY(2, 2, KEY_J), - KEY(2, 3, KEY_K), - KEY(2, 4, KEY_3), - KEY(3, 0, KEY_M), - KEY(3, 1, KEY_N), - KEY(3, 2, KEY_O), + KEY(3, 2, KEY_K), + KEY(4, 2, KEY_3), + KEY(0, 3, KEY_M), + KEY(1, 3, KEY_N), + KEY(2, 3, KEY_O), KEY(3, 3, KEY_P), - KEY(3, 4, KEY_Q), - KEY(4, 0, KEY_R), - KEY(4, 1, KEY_4), - KEY(4, 2, KEY_T), - KEY(4, 3, KEY_U), + KEY(4, 3, KEY_Q), + KEY(0, 4, KEY_R), + KEY(1, 4, KEY_4), + KEY(2, 4, KEY_T), + KEY(3, 4, KEY_U), KEY(4, 4, KEY_ENTER), - KEY(5, 0, KEY_V), - KEY(5, 1, KEY_W), - KEY(5, 2, KEY_L), - KEY(5, 3, KEY_S), - KEY(5, 4, KEY_ENTER), - 0 + KEY(0, 5, KEY_V), + KEY(1, 5, KEY_W), + KEY(2, 5, KEY_L), + KEY(3, 5, KEY_S), + KEY(4, 5, KEY_ENTER), }; static struct mtd_partition h4_partitions[] = { @@ -136,12 +135,16 @@ static struct platform_device h4_flash_device = { .resource = &h4_flash_resource, }; +static const struct matrix_keymap_data h4_keymap_data = { + .keymap = h4_keymap, + .keymap_size = ARRAY_SIZE(h4_keymap), +}; + static struct omap_kp_platform_data h4_kp_data = { .rows = 6, .cols = 7, - .keymap = h4_keymap, - .keymapsize = ARRAY_SIZE(h4_keymap), - .rep = 1, + .keymap_data = &h4_keymap_data, + .rep = true, .row_gpios = row_gpios, .col_gpios = col_gpios, }; diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c index b82f2319a09..d4a9aa41e87 100644 --- a/arch/arm/mach-omap2/board-omap4panda.c +++ b/arch/arm/mach-omap2/board-omap4panda.c @@ -142,6 +142,7 @@ static struct omap2_hsmmc_info mmc[] = { .mmc = 1, .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, .gpio_wp = -EINVAL, + .gpio_cd = -EINVAL, }, {} /* Terminator */ }; diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index fd95ccf8be5..e75e240cad6 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -359,17 +359,12 @@ static struct regulator_consumer_supply rx51_vio_supplies[] = { REGULATOR_SUPPLY("DVDD", "2-0019"), }; -#if defined(CONFIG_FB_OMAP2) || defined(CONFIG_FB_OMAP2_MODULE) -extern struct platform_device rx51_display_device; -#endif - static struct regulator_consumer_supply rx51_vaux1_consumers[] = { -#if defined(CONFIG_FB_OMAP2) || defined(CONFIG_FB_OMAP2_MODULE) - { - .supply = "vdds_sdi", - .dev = &rx51_display_device.dev, - }, -#endif + REGULATOR_SUPPLY("vdds_sdi", "omapdss"), +}; + +static struct regulator_consumer_supply rx51_vdac_supply[] = { + REGULATOR_SUPPLY("vdda_dac", "omapdss"), }; static struct regulator_init_data rx51_vaux1 = { @@ -489,14 +484,17 @@ static struct regulator_init_data rx51_vsim = { static struct regulator_init_data rx51_vdac = { .constraints = { + .name = "VDAC", .min_uV = 1800000, .max_uV = 1800000, + .apply_uV = true, .valid_modes_mask = REGULATOR_MODE_NORMAL | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE + .valid_ops_mask = REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS, }, + .num_consumer_supplies = 1, + .consumer_supplies = rx51_vdac_supply, }; static struct regulator_init_data rx51_vio = { diff --git a/arch/arm/mach-omap2/board-rx51-video.c b/arch/arm/mach-omap2/board-rx51-video.c index 9919581f391..acd670054d9 100644 --- a/arch/arm/mach-omap2/board-rx51-video.c +++ b/arch/arm/mach-omap2/board-rx51-video.c @@ -24,9 +24,6 @@ #include "mux.h" #define RX51_LCD_RESET_GPIO 90 -/* REVISIT to verify with rx51.c at sound/soc/omap */ -#define RX51_TVOUT_SEL_GPIO 40 - #if defined(CONFIG_FB_OMAP2) || defined(CONFIG_FB_OMAP2_MODULE) @@ -41,17 +38,6 @@ static void rx51_lcd_disable(struct omap_dss_device *dssdev) gpio_set_value(dssdev->reset_gpio, 0); } -static int rx51_tvout_enable(struct omap_dss_device *dssdev) -{ - gpio_set_value(dssdev->reset_gpio, 1); - return 0; -} - -static void rx51_tvout_disable(struct omap_dss_device *dssdev) -{ - gpio_set_value(dssdev->reset_gpio, 0); -} - static struct omap_dss_device rx51_lcd_device = { .name = "lcd", .driver_name = "panel-acx565akm", @@ -67,9 +53,6 @@ static struct omap_dss_device rx51_tv_device = { .type = OMAP_DISPLAY_TYPE_VENC, .driver_name = "venc", .phy.venc.type = OMAP_DSS_VENC_TYPE_COMPOSITE, - .reset_gpio = RX51_TVOUT_SEL_GPIO, - .platform_enable = rx51_tvout_enable, - .platform_disable = rx51_tvout_disable, }; static struct omap_dss_device *rx51_dss_devices[] = { @@ -112,9 +95,6 @@ static int __init rx51_video_init(void) gpio_direction_output(RX51_LCD_RESET_GPIO, 1); - /* REVISIT to verify with rx51.c at sound/soc/omap */ - gpio_direction_output(RX51_TVOUT_SEL_GPIO, 1); - platform_add_devices(rx51_video_devices, ARRAY_SIZE(rx51_video_devices)); return 0; diff --git a/arch/arm/mach-omap2/control.c b/arch/arm/mach-omap2/control.c index 1fa3294b604..0269bb055b6 100644 --- a/arch/arm/mach-omap2/control.c +++ b/arch/arm/mach-omap2/control.c @@ -239,9 +239,19 @@ void omap3_save_scratchpad_contents(void) struct omap3_scratchpad_prcm_block prcm_block_contents; struct omap3_scratchpad_sdrc_block sdrc_block_contents; - /* Populate the Scratchpad contents */ + /* + * Populate the Scratchpad contents + * + * The "get_*restore_pointer" functions are used to provide a + * physical restore address where the ROM code jumps while waking + * up from MPU OFF/OSWR state. + * The restore pointer is stored into the scratchpad. + */ scratchpad_contents.boot_config_ptr = 0x0; - if (omap_rev() != OMAP3430_REV_ES3_0 && + if (cpu_is_omap3630()) + scratchpad_contents.public_restore_ptr = + virt_to_phys(get_omap3630_restore_pointer()); + else if (omap_rev() != OMAP3430_REV_ES3_0 && omap_rev() != OMAP3430_REV_ES3_1) scratchpad_contents.public_restore_ptr = virt_to_phys(get_restore_pointer()); @@ -474,4 +484,12 @@ void omap3_control_restore_context(void) omap_ctrl_writel(control_context.csi, OMAP343X_CONTROL_CSI); return; } + +void omap3630_ctrl_disable_rta(void) +{ + if (!cpu_is_omap3630()) + return; + omap_ctrl_writel(OMAP36XX_RTA_DISABLE, OMAP36XX_CONTROL_MEM_RTA_CTRL); +} + #endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */ diff --git a/arch/arm/mach-omap2/control.h b/arch/arm/mach-omap2/control.h index b6c6b7c450b..ea20dc31052 100644 --- a/arch/arm/mach-omap2/control.h +++ b/arch/arm/mach-omap2/control.h @@ -204,6 +204,10 @@ #define OMAP343X_CONTROL_WKUP_DEBOBS3 (OMAP343X_CONTROL_GENERAL_WKUP + 0x014) #define OMAP343X_CONTROL_WKUP_DEBOBS4 (OMAP343X_CONTROL_GENERAL_WKUP + 0x018) +/* 36xx-only RTA - Retention till Accesss control registers and bits */ +#define OMAP36XX_CONTROL_MEM_RTA_CTRL 0x40C +#define OMAP36XX_RTA_DISABLE 0x0 + /* 34xx D2D idle-related pins, handled by PM core */ #define OMAP3_PADCONF_SAD2D_MSTANDBY 0x250 #define OMAP3_PADCONF_SAD2D_IDLEACK 0x254 @@ -270,6 +274,8 @@ #define OMAP343X_SCRATCHPAD_ROM (OMAP343X_CTRL_BASE + 0x860) #define OMAP343X_SCRATCHPAD (OMAP343X_CTRL_BASE + 0x910) #define OMAP343X_SCRATCHPAD_ROM_OFFSET 0x19C +#define OMAP343X_SCRATCHPAD_REGADDR(reg) OMAP2_L4_IO_ADDRESS(\ + OMAP343X_SCRATCHPAD + reg) /* AM35XX_CONTROL_IPSS_CLK_CTRL bits */ #define AM35XX_USBOTG_VBUSP_CLK_SHIFT 0 @@ -309,7 +315,7 @@ #define FEAT_SGX_NONE 2 #define OMAP3_IVA_SHIFT 12 -#define OMAP3_IVA_MASK (1 << OMAP3_SGX_SHIFT) +#define OMAP3_IVA_MASK (1 << OMAP3_IVA_SHIFT) #define FEAT_IVA 0 #define FEAT_IVA_NONE 1 @@ -347,10 +353,11 @@ extern void omap3_save_scratchpad_contents(void); extern void omap3_clear_scratchpad_contents(void); extern u32 *get_restore_pointer(void); extern u32 *get_es3_restore_pointer(void); +extern u32 *get_omap3630_restore_pointer(void); extern u32 omap3_arm_context[128]; extern void omap3_control_save_context(void); extern void omap3_control_restore_context(void); - +extern void omap3630_ctrl_disable_rta(void); #else #define omap_ctrl_base_get() 0 #define omap_ctrl_readb(x) 0 diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c index 0d50b45d041..0fb619c5258 100644 --- a/arch/arm/mach-omap2/cpuidle34xx.c +++ b/arch/arm/mach-omap2/cpuidle34xx.c @@ -293,25 +293,26 @@ select_state: DEFINE_PER_CPU(struct cpuidle_device, omap3_idle_dev); /** - * omap3_cpuidle_update_states - Update the cpuidle states. + * omap3_cpuidle_update_states() - Update the cpuidle states + * @mpu_deepest_state: Enable states upto and including this for mpu domain + * @core_deepest_state: Enable states upto and including this for core domain * - * Currently, this function toggles the validity of idle states based upon - * the flag 'enable_off_mode'. When the flag is set all states are valid. - * Else, states leading to OFF state set to be invalid. + * This goes through the list of states available and enables and disables the + * validity of C states based on deepest state that can be achieved for the + * variable domain */ -void omap3_cpuidle_update_states(void) +void omap3_cpuidle_update_states(u32 mpu_deepest_state, u32 core_deepest_state) { int i; for (i = OMAP3_STATE_C1; i < OMAP3_MAX_STATES; i++) { struct omap3_processor_cx *cx = &omap3_power_states[i]; - if (enable_off_mode) { + if ((cx->mpu_state >= mpu_deepest_state) && + (cx->core_state >= core_deepest_state)) { cx->valid = 1; } else { - if ((cx->mpu_state == PWRDM_POWER_OFF) || - (cx->core_state == PWRDM_POWER_OFF)) - cx->valid = 0; + cx->valid = 0; } } } @@ -452,6 +453,18 @@ void omap_init_power_states(void) omap3_power_states[OMAP3_STATE_C7].core_state = PWRDM_POWER_OFF; omap3_power_states[OMAP3_STATE_C7].flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_CHECK_BM; + + /* + * Erratum i583: implementation for ES rev < Es1.2 on 3630. We cannot + * enable OFF mode in a stable form for previous revisions. + * we disable C7 state as a result. + */ + if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583)) { + omap3_power_states[OMAP3_STATE_C7].valid = 0; + cpuidle_params_table[OMAP3_STATE_C7].valid = 0; + WARN_ONCE(1, "%s: core off state C7 disabled due to i583\n", + __func__); + } } struct cpuidle_driver omap3_idle_driver = { @@ -504,7 +517,10 @@ int __init omap3_idle_init(void) return -EINVAL; dev->state_count = count; - omap3_cpuidle_update_states(); + if (enable_off_mode) + omap3_cpuidle_update_states(PWRDM_POWER_OFF, PWRDM_POWER_OFF); + else + omap3_cpuidle_update_states(PWRDM_POWER_RET, PWRDM_POWER_RET); if (cpuidle_register_device(dev)) { printk(KERN_ERR "%s: CPUidle register device failed\n", diff --git a/arch/arm/mach-omap2/dma.c b/arch/arm/mach-omap2/dma.c new file mode 100644 index 00000000000..d2f15f5cfd3 --- /dev/null +++ b/arch/arm/mach-omap2/dma.c @@ -0,0 +1,297 @@ +/* + * OMAP2+ DMA driver + * + * Copyright (C) 2003 - 2008 Nokia Corporation + * Author: Juha Yrjölä <juha.yrjola@nokia.com> + * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com> + * Graphics DMA and LCD DMA graphics tranformations + * by Imre Deak <imre.deak@nokia.com> + * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc. + * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc. + * + * Copyright (C) 2009 Texas Instruments + * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com> + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * Converted DMA library into platform driver + * - G, Manjunath Kondaiah <manjugk@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/err.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/device.h> + +#include <plat/omap_hwmod.h> +#include <plat/omap_device.h> +#include <plat/dma.h> + +#define OMAP2_DMA_STRIDE 0x60 + +static u32 errata; +static u8 dma_stride; + +static struct omap_dma_dev_attr *d; + +static enum omap_reg_offsets dma_common_ch_start, dma_common_ch_end; + +static u16 reg_map[] = { + [REVISION] = 0x00, + [GCR] = 0x78, + [IRQSTATUS_L0] = 0x08, + [IRQSTATUS_L1] = 0x0c, + [IRQSTATUS_L2] = 0x10, + [IRQSTATUS_L3] = 0x14, + [IRQENABLE_L0] = 0x18, + [IRQENABLE_L1] = 0x1c, + [IRQENABLE_L2] = 0x20, + [IRQENABLE_L3] = 0x24, + [SYSSTATUS] = 0x28, + [OCP_SYSCONFIG] = 0x2c, + [CAPS_0] = 0x64, + [CAPS_2] = 0x6c, + [CAPS_3] = 0x70, + [CAPS_4] = 0x74, + + /* Common register offsets */ + [CCR] = 0x80, + [CLNK_CTRL] = 0x84, + [CICR] = 0x88, + [CSR] = 0x8c, + [CSDP] = 0x90, + [CEN] = 0x94, + [CFN] = 0x98, + [CSEI] = 0xa4, + [CSFI] = 0xa8, + [CDEI] = 0xac, + [CDFI] = 0xb0, + [CSAC] = 0xb4, + [CDAC] = 0xb8, + + /* Channel specific register offsets */ + [CSSA] = 0x9c, + [CDSA] = 0xa0, + [CCEN] = 0xbc, + [CCFN] = 0xc0, + [COLOR] = 0xc4, + + /* OMAP4 specific registers */ + [CDP] = 0xd0, + [CNDP] = 0xd4, + [CCDN] = 0xd8, +}; + +static struct omap_device_pm_latency omap2_dma_latency[] = { + { + .deactivate_func = omap_device_idle_hwmods, + .activate_func = omap_device_enable_hwmods, + .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST, + }, +}; + +static void __iomem *dma_base; +static inline void dma_write(u32 val, int reg, int lch) +{ + u8 stride; + u32 offset; + + stride = (reg >= dma_common_ch_start) ? dma_stride : 0; + offset = reg_map[reg] + (stride * lch); + __raw_writel(val, dma_base + offset); +} + +static inline u32 dma_read(int reg, int lch) +{ + u8 stride; + u32 offset, val; + + stride = (reg >= dma_common_ch_start) ? dma_stride : 0; + offset = reg_map[reg] + (stride * lch); + val = __raw_readl(dma_base + offset); + return val; +} + +static inline void omap2_disable_irq_lch(int lch) +{ + u32 val; + + val = dma_read(IRQENABLE_L0, lch); + val &= ~(1 << lch); + dma_write(val, IRQENABLE_L0, lch); +} + +static void omap2_clear_dma(int lch) +{ + int i = dma_common_ch_start; + + for (; i <= dma_common_ch_end; i += 1) + dma_write(0, i, lch); +} + +static void omap2_show_dma_caps(void) +{ + u8 revision = dma_read(REVISION, 0) & 0xff; + printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n", + revision >> 4, revision & 0xf); + return; +} + +static u32 configure_dma_errata(void) +{ + + /* + * Errata applicable for OMAP2430ES1.0 and all omap2420 + * + * I. + * Erratum ID: Not Available + * Inter Frame DMA buffering issue DMA will wrongly + * buffer elements if packing and bursting is enabled. This might + * result in data gets stalled in FIFO at the end of the block. + * Workaround: DMA channels must have BUFFERING_DISABLED bit set to + * guarantee no data will stay in the DMA FIFO in case inter frame + * buffering occurs + * + * II. + * Erratum ID: Not Available + * DMA may hang when several channels are used in parallel + * In the following configuration, DMA channel hanging can occur: + * a. Channel i, hardware synchronized, is enabled + * b. Another channel (Channel x), software synchronized, is enabled. + * c. Channel i is disabled before end of transfer + * d. Channel i is reenabled. + * e. Steps 1 to 4 are repeated a certain number of times. + * f. A third channel (Channel y), software synchronized, is enabled. + * Channel x and Channel y may hang immediately after step 'f'. + * Workaround: + * For any channel used - make sure NextLCH_ID is set to the value j. + */ + if (cpu_is_omap2420() || (cpu_is_omap2430() && + (omap_type() == OMAP2430_REV_ES1_0))) { + + SET_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING); + SET_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS); + } + + /* + * Erratum ID: i378: OMAP2+: sDMA Channel is not disabled + * after a transaction error. + * Workaround: SW should explicitely disable the channel. + */ + if (cpu_class_is_omap2()) + SET_DMA_ERRATA(DMA_ERRATA_i378); + + /* + * Erratum ID: i541: sDMA FIFO draining does not finish + * If sDMA channel is disabled on the fly, sDMA enters standby even + * through FIFO Drain is still in progress + * Workaround: Put sDMA in NoStandby more before a logical channel is + * disabled, then put it back to SmartStandby right after the channel + * finishes FIFO draining. + */ + if (cpu_is_omap34xx()) + SET_DMA_ERRATA(DMA_ERRATA_i541); + + /* + * Erratum ID: i88 : Special programming model needed to disable DMA + * before end of block. + * Workaround: software must ensure that the DMA is configured in No + * Standby mode(DMAx_OCP_SYSCONFIG.MIDLEMODE = "01") + */ + if (omap_type() == OMAP3430_REV_ES1_0) + SET_DMA_ERRATA(DMA_ERRATA_i88); + + /* + * Erratum 3.2/3.3: sometimes 0 is returned if CSAC/CDAC is + * read before the DMA controller finished disabling the channel. + */ + SET_DMA_ERRATA(DMA_ERRATA_3_3); + + /* + * Erratum ID: Not Available + * A bug in ROM code leaves IRQ status for channels 0 and 1 uncleared + * after secure sram context save and restore. + * Work around: Hence we need to manually clear those IRQs to avoid + * spurious interrupts. This affects only secure devices. + */ + if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP)) + SET_DMA_ERRATA(DMA_ROMCODE_BUG); + + return errata; +} + +/* One time initializations */ +static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused) +{ + struct omap_device *od; + struct omap_system_dma_plat_info *p; + struct resource *mem; + char *name = "omap_dma_system"; + + dma_stride = OMAP2_DMA_STRIDE; + dma_common_ch_start = CSDP; + if (cpu_is_omap3630() || cpu_is_omap4430()) + dma_common_ch_end = CCDN; + else + dma_common_ch_end = CCFN; + + p = kzalloc(sizeof(struct omap_system_dma_plat_info), GFP_KERNEL); + if (!p) { + pr_err("%s: Unable to allocate pdata for %s:%s\n", + __func__, name, oh->name); + return -ENOMEM; + } + + p->dma_attr = (struct omap_dma_dev_attr *)oh->dev_attr; + p->disable_irq_lch = omap2_disable_irq_lch; + p->show_dma_caps = omap2_show_dma_caps; + p->clear_dma = omap2_clear_dma; + p->dma_write = dma_write; + p->dma_read = dma_read; + + p->clear_lch_regs = NULL; + + p->errata = configure_dma_errata(); + + od = omap_device_build(name, 0, oh, p, sizeof(*p), + omap2_dma_latency, ARRAY_SIZE(omap2_dma_latency), 0); + kfree(p); + if (IS_ERR(od)) { + pr_err("%s: Cant build omap_device for %s:%s.\n", + __func__, name, oh->name); + return IS_ERR(od); + } + + mem = platform_get_resource(&od->pdev, IORESOURCE_MEM, 0); + if (!mem) { + dev_err(&od->pdev.dev, "%s: no mem resource\n", __func__); + return -EINVAL; + } + dma_base = ioremap(mem->start, resource_size(mem)); + if (!dma_base) { + dev_err(&od->pdev.dev, "%s: ioremap fail\n", __func__); + return -ENOMEM; + } + + d = oh->dev_attr; + d->chan = kzalloc(sizeof(struct omap_dma_lch) * + (d->lch_count), GFP_KERNEL); + + if (!d->chan) { + dev_err(&od->pdev.dev, "%s: kzalloc fail\n", __func__); + return -ENOMEM; + } + return 0; +} + +static int __init omap2_system_dma_init(void) +{ + return omap_hwmod_for_each_by_class("dma", + omap2_system_dma_init_dev, NULL); +} +arch_initcall(omap2_system_dma_init); diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 4605d5073a9..5577ab2faad 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -347,8 +347,7 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0, else if (cpu_is_omap44xx()) omap44xx_hwmod_init(); - /* The OPP tables have to be registered before a clk init */ - omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps); + omap_pm_if_early_init(); if (cpu_is_omap2420()) omap2420_clk_init(); diff --git a/arch/arm/mach-omap2/omap_hwmod_2420_data.c b/arch/arm/mach-omap2/omap_hwmod_2420_data.c index d9534259979..42606f6b0cd 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2420_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2420_data.c @@ -42,6 +42,7 @@ static struct omap_hwmod omap2420_gpio1_hwmod; static struct omap_hwmod omap2420_gpio2_hwmod; static struct omap_hwmod omap2420_gpio3_hwmod; static struct omap_hwmod omap2420_gpio4_hwmod; +static struct omap_hwmod omap2420_dma_system_hwmod; /* L3 -> L4_CORE interface */ static struct omap_hwmod_ocp_if omap2420_l3_main__l4_core = { @@ -779,6 +780,88 @@ static struct omap_hwmod omap2420_gpio4_hwmod = { .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP2420), }; +/* system dma */ +static struct omap_hwmod_class_sysconfig omap2420_dma_sysc = { + .rev_offs = 0x0000, + .sysc_offs = 0x002c, + .syss_offs = 0x0028, + .sysc_flags = (SYSC_HAS_SOFTRESET | SYSC_HAS_MIDLEMODE | + SYSC_HAS_CLOCKACTIVITY | SYSC_HAS_EMUFREE | + SYSC_HAS_AUTOIDLE), + .idlemodes = (MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART), + .sysc_fields = &omap_hwmod_sysc_type1, +}; + +static struct omap_hwmod_class omap2420_dma_hwmod_class = { + .name = "dma", + .sysc = &omap2420_dma_sysc, +}; + +/* dma attributes */ +static struct omap_dma_dev_attr dma_dev_attr = { + .dev_caps = RESERVE_CHANNEL | DMA_LINKED_LCH | GLOBAL_PRIORITY | + IS_CSSA_32 | IS_CDSA_32, + .lch_count = 32, +}; + +static struct omap_hwmod_irq_info omap2420_dma_system_irqs[] = { + { .name = "0", .irq = 12 }, /* INT_24XX_SDMA_IRQ0 */ + { .name = "1", .irq = 13 }, /* INT_24XX_SDMA_IRQ1 */ + { .name = "2", .irq = 14 }, /* INT_24XX_SDMA_IRQ2 */ + { .name = "3", .irq = 15 }, /* INT_24XX_SDMA_IRQ3 */ +}; + +static struct omap_hwmod_addr_space omap2420_dma_system_addrs[] = { + { + .pa_start = 0x48056000, + .pa_end = 0x4a0560ff, + .flags = ADDR_TYPE_RT + }, +}; + +/* dma_system -> L3 */ +static struct omap_hwmod_ocp_if omap2420_dma_system__l3 = { + .master = &omap2420_dma_system_hwmod, + .slave = &omap2420_l3_main_hwmod, + .clk = "core_l3_ck", + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + +/* dma_system master ports */ +static struct omap_hwmod_ocp_if *omap2420_dma_system_masters[] = { + &omap2420_dma_system__l3, +}; + +/* l4_core -> dma_system */ +static struct omap_hwmod_ocp_if omap2420_l4_core__dma_system = { + .master = &omap2420_l4_core_hwmod, + .slave = &omap2420_dma_system_hwmod, + .clk = "sdma_ick", + .addr = omap2420_dma_system_addrs, + .addr_cnt = ARRAY_SIZE(omap2420_dma_system_addrs), + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + +/* dma_system slave ports */ +static struct omap_hwmod_ocp_if *omap2420_dma_system_slaves[] = { + &omap2420_l4_core__dma_system, +}; + +static struct omap_hwmod omap2420_dma_system_hwmod = { + .name = "dma", + .class = &omap2420_dma_hwmod_class, + .mpu_irqs = omap2420_dma_system_irqs, + .mpu_irqs_cnt = ARRAY_SIZE(omap2420_dma_system_irqs), + .main_clk = "core_l3_ck", + .slaves = omap2420_dma_system_slaves, + .slaves_cnt = ARRAY_SIZE(omap2420_dma_system_slaves), + .masters = omap2420_dma_system_masters, + .masters_cnt = ARRAY_SIZE(omap2420_dma_system_masters), + .dev_attr = &dma_dev_attr, + .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP2420), + .flags = HWMOD_NO_IDLEST, +}; + static __initdata struct omap_hwmod *omap2420_hwmods[] = { &omap2420_l3_main_hwmod, &omap2420_l4_core_hwmod, @@ -797,6 +880,9 @@ static __initdata struct omap_hwmod *omap2420_hwmods[] = { &omap2420_gpio2_hwmod, &omap2420_gpio3_hwmod, &omap2420_gpio4_hwmod, + + /* dma_system class*/ + &omap2420_dma_system_hwmod, NULL, }; diff --git a/arch/arm/mach-omap2/omap_hwmod_2430_data.c b/arch/arm/mach-omap2/omap_hwmod_2430_data.c index ab1d662cb07..3315d241fee 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2430_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2430_data.c @@ -43,6 +43,7 @@ static struct omap_hwmod omap2430_gpio2_hwmod; static struct omap_hwmod omap2430_gpio3_hwmod; static struct omap_hwmod omap2430_gpio4_hwmod; static struct omap_hwmod omap2430_gpio5_hwmod; +static struct omap_hwmod omap2430_dma_system_hwmod; /* L3 -> L4_CORE interface */ static struct omap_hwmod_ocp_if omap2430_l3_main__l4_core = { @@ -838,6 +839,88 @@ static struct omap_hwmod omap2430_gpio5_hwmod = { .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP2430), }; +/* dma_system */ +static struct omap_hwmod_class_sysconfig omap2430_dma_sysc = { + .rev_offs = 0x0000, + .sysc_offs = 0x002c, + .syss_offs = 0x0028, + .sysc_flags = (SYSC_HAS_SOFTRESET | SYSC_HAS_MIDLEMODE | + SYSC_HAS_CLOCKACTIVITY | SYSC_HAS_EMUFREE | + SYSC_HAS_AUTOIDLE), + .idlemodes = (MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART), + .sysc_fields = &omap_hwmod_sysc_type1, +}; + +static struct omap_hwmod_class omap2430_dma_hwmod_class = { + .name = "dma", + .sysc = &omap2430_dma_sysc, +}; + +/* dma attributes */ +static struct omap_dma_dev_attr dma_dev_attr = { + .dev_caps = RESERVE_CHANNEL | DMA_LINKED_LCH | GLOBAL_PRIORITY | + IS_CSSA_32 | IS_CDSA_32 | IS_RW_PRIORITY, + .lch_count = 32, +}; + +static struct omap_hwmod_irq_info omap2430_dma_system_irqs[] = { + { .name = "0", .irq = 12 }, /* INT_24XX_SDMA_IRQ0 */ + { .name = "1", .irq = 13 }, /* INT_24XX_SDMA_IRQ1 */ + { .name = "2", .irq = 14 }, /* INT_24XX_SDMA_IRQ2 */ + { .name = "3", .irq = 15 }, /* INT_24XX_SDMA_IRQ3 */ +}; + +static struct omap_hwmod_addr_space omap2430_dma_system_addrs[] = { + { + .pa_start = 0x48056000, + .pa_end = 0x4a0560ff, + .flags = ADDR_TYPE_RT + }, +}; + +/* dma_system -> L3 */ +static struct omap_hwmod_ocp_if omap2430_dma_system__l3 = { + .master = &omap2430_dma_system_hwmod, + .slave = &omap2430_l3_main_hwmod, + .clk = "core_l3_ck", + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + +/* dma_system master ports */ +static struct omap_hwmod_ocp_if *omap2430_dma_system_masters[] = { + &omap2430_dma_system__l3, +}; + +/* l4_core -> dma_system */ +static struct omap_hwmod_ocp_if omap2430_l4_core__dma_system = { + .master = &omap2430_l4_core_hwmod, + .slave = &omap2430_dma_system_hwmod, + .clk = "sdma_ick", + .addr = omap2430_dma_system_addrs, + .addr_cnt = ARRAY_SIZE(omap2430_dma_system_addrs), + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + +/* dma_system slave ports */ +static struct omap_hwmod_ocp_if *omap2430_dma_system_slaves[] = { + &omap2430_l4_core__dma_system, +}; + +static struct omap_hwmod omap2430_dma_system_hwmod = { + .name = "dma", + .class = &omap2430_dma_hwmod_class, + .mpu_irqs = omap2430_dma_system_irqs, + .mpu_irqs_cnt = ARRAY_SIZE(omap2430_dma_system_irqs), + .main_clk = "core_l3_ck", + .slaves = omap2430_dma_system_slaves, + .slaves_cnt = ARRAY_SIZE(omap2430_dma_system_slaves), + .masters = omap2430_dma_system_masters, + .masters_cnt = ARRAY_SIZE(omap2430_dma_system_masters), + .dev_attr = &dma_dev_attr, + .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP2430), + .flags = HWMOD_NO_IDLEST, +}; + static __initdata struct omap_hwmod *omap2430_hwmods[] = { &omap2430_l3_main_hwmod, &omap2430_l4_core_hwmod, @@ -857,6 +940,9 @@ static __initdata struct omap_hwmod *omap2430_hwmods[] = { &omap2430_gpio3_hwmod, &omap2430_gpio4_hwmod, &omap2430_gpio5_hwmod, + + /* dma_system class*/ + &omap2430_dma_system_hwmod, NULL, }; diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index 2687be10d7a..d5acb63ba9e 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -52,6 +52,8 @@ static struct omap_hwmod omap3xxx_gpio4_hwmod; static struct omap_hwmod omap3xxx_gpio5_hwmod; static struct omap_hwmod omap3xxx_gpio6_hwmod; +static struct omap_hwmod omap3xxx_dma_system_hwmod; + /* L3 -> L4_CORE interface */ static struct omap_hwmod_ocp_if omap3xxx_l3_main__l4_core = { .master = &omap3xxx_l3_main_hwmod, @@ -1090,6 +1092,98 @@ static struct omap_hwmod omap3xxx_gpio6_hwmod = { .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP3430), }; +/* dma_system -> L3 */ +static struct omap_hwmod_ocp_if omap3xxx_dma_system__l3 = { + .master = &omap3xxx_dma_system_hwmod, + .slave = &omap3xxx_l3_main_hwmod, + .clk = "core_l3_ick", + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + +/* dma attributes */ +static struct omap_dma_dev_attr dma_dev_attr = { + .dev_caps = RESERVE_CHANNEL | DMA_LINKED_LCH | GLOBAL_PRIORITY | + IS_CSSA_32 | IS_CDSA_32 | IS_RW_PRIORITY, + .lch_count = 32, +}; + +static struct omap_hwmod_class_sysconfig omap3xxx_dma_sysc = { + .rev_offs = 0x0000, + .sysc_offs = 0x002c, + .syss_offs = 0x0028, + .sysc_flags = (SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET | + SYSC_HAS_MIDLEMODE | SYSC_HAS_CLOCKACTIVITY | + SYSC_HAS_EMUFREE | SYSC_HAS_AUTOIDLE), + .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | + MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART), + .sysc_fields = &omap_hwmod_sysc_type1, +}; + +static struct omap_hwmod_class omap3xxx_dma_hwmod_class = { + .name = "dma", + .sysc = &omap3xxx_dma_sysc, +}; + +/* dma_system */ +static struct omap_hwmod_irq_info omap3xxx_dma_system_irqs[] = { + { .name = "0", .irq = 12 }, /* INT_24XX_SDMA_IRQ0 */ + { .name = "1", .irq = 13 }, /* INT_24XX_SDMA_IRQ1 */ + { .name = "2", .irq = 14 }, /* INT_24XX_SDMA_IRQ2 */ + { .name = "3", .irq = 15 }, /* INT_24XX_SDMA_IRQ3 */ +}; + +static struct omap_hwmod_addr_space omap3xxx_dma_system_addrs[] = { + { + .pa_start = 0x48056000, + .pa_end = 0x4a0560ff, + .flags = ADDR_TYPE_RT + }, +}; + +/* dma_system master ports */ +static struct omap_hwmod_ocp_if *omap3xxx_dma_system_masters[] = { + &omap3xxx_dma_system__l3, +}; + +/* l4_cfg -> dma_system */ +static struct omap_hwmod_ocp_if omap3xxx_l4_core__dma_system = { + .master = &omap3xxx_l4_core_hwmod, + .slave = &omap3xxx_dma_system_hwmod, + .clk = "core_l4_ick", + .addr = omap3xxx_dma_system_addrs, + .addr_cnt = ARRAY_SIZE(omap3xxx_dma_system_addrs), + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + +/* dma_system slave ports */ +static struct omap_hwmod_ocp_if *omap3xxx_dma_system_slaves[] = { + &omap3xxx_l4_core__dma_system, +}; + +static struct omap_hwmod omap3xxx_dma_system_hwmod = { + .name = "dma", + .class = &omap3xxx_dma_hwmod_class, + .mpu_irqs = omap3xxx_dma_system_irqs, + .mpu_irqs_cnt = ARRAY_SIZE(omap3xxx_dma_system_irqs), + .main_clk = "core_l3_ick", + .prcm = { + .omap2 = { + .module_offs = CORE_MOD, + .prcm_reg_id = 1, + .module_bit = OMAP3430_ST_SDMA_SHIFT, + .idlest_reg_id = 1, + .idlest_idle_bit = OMAP3430_ST_SDMA_SHIFT, + }, + }, + .slaves = omap3xxx_dma_system_slaves, + .slaves_cnt = ARRAY_SIZE(omap3xxx_dma_system_slaves), + .masters = omap3xxx_dma_system_masters, + .masters_cnt = ARRAY_SIZE(omap3xxx_dma_system_masters), + .dev_attr = &dma_dev_attr, + .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP3430), + .flags = HWMOD_NO_IDLEST, +}; + static __initdata struct omap_hwmod *omap3xxx_hwmods[] = { &omap3xxx_l3_main_hwmod, &omap3xxx_l4_core_hwmod, @@ -1113,6 +1207,9 @@ static __initdata struct omap_hwmod *omap3xxx_hwmods[] = { &omap3xxx_gpio4_hwmod, &omap3xxx_gpio5_hwmod, &omap3xxx_gpio6_hwmod, + + /* dma_system class*/ + &omap3xxx_dma_system_hwmod, NULL, }; diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index d258936410f..f9778fba832 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -23,6 +23,7 @@ #include <plat/omap_hwmod.h> #include <plat/cpu.h> #include <plat/gpio.h> +#include <plat/dma.h> #include "omap_hwmod_common_data.h" @@ -36,6 +37,7 @@ #define OMAP44XX_DMA_REQ_START 1 /* Backward references (IPs with Bus Master capability) */ +static struct omap_hwmod omap44xx_dma_system_hwmod; static struct omap_hwmod omap44xx_dmm_hwmod; static struct omap_hwmod omap44xx_emif_fw_hwmod; static struct omap_hwmod omap44xx_l3_instr_hwmod; @@ -216,6 +218,14 @@ static struct omap_hwmod_ocp_if omap44xx_l3_main_1__l3_main_2 = { .user = OCP_USER_MPU | OCP_USER_SDMA, }; +/* dma_system -> l3_main_2 */ +static struct omap_hwmod_ocp_if omap44xx_dma_system__l3_main_2 = { + .master = &omap44xx_dma_system_hwmod, + .slave = &omap44xx_l3_main_2_hwmod, + .clk = "l3_div_ck", + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + /* l4_cfg -> l3_main_2 */ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_2 = { .master = &omap44xx_l4_cfg_hwmod, @@ -226,6 +236,7 @@ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_2 = { /* l3_main_2 slave ports */ static struct omap_hwmod_ocp_if *omap44xx_l3_main_2_slaves[] = { + &omap44xx_dma_system__l3_main_2, &omap44xx_l3_main_1__l3_main_2, &omap44xx_l4_cfg__l3_main_2, }; @@ -1376,6 +1387,93 @@ static struct omap_hwmod omap44xx_gpio6_hwmod = { .slaves_cnt = ARRAY_SIZE(omap44xx_gpio6_slaves), .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP4430), }; + +/* + * 'dma' class + * dma controller for data exchange between memory to memory (i.e. internal or + * external memory) and gp peripherals to memory or memory to gp peripherals + */ + +static struct omap_hwmod_class_sysconfig omap44xx_dma_sysc = { + .rev_offs = 0x0000, + .sysc_offs = 0x002c, + .syss_offs = 0x0028, + .sysc_flags = (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY | + SYSC_HAS_EMUFREE | SYSC_HAS_MIDLEMODE | + SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET | + SYSS_HAS_RESET_STATUS), + .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | + MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART), + .sysc_fields = &omap_hwmod_sysc_type1, +}; + +/* dma attributes */ +static struct omap_dma_dev_attr dma_dev_attr = { + .dev_caps = RESERVE_CHANNEL | DMA_LINKED_LCH | GLOBAL_PRIORITY | + IS_CSSA_32 | IS_CDSA_32 | IS_RW_PRIORITY, + .lch_count = 32, +}; + +static struct omap_hwmod_class omap44xx_dma_hwmod_class = { + .name = "dma", + .sysc = &omap44xx_dma_sysc, +}; + +/* dma_system */ +static struct omap_hwmod_irq_info omap44xx_dma_system_irqs[] = { + { .name = "0", .irq = 12 + OMAP44XX_IRQ_GIC_START }, + { .name = "1", .irq = 13 + OMAP44XX_IRQ_GIC_START }, + { .name = "2", .irq = 14 + OMAP44XX_IRQ_GIC_START }, + { .name = "3", .irq = 15 + OMAP44XX_IRQ_GIC_START }, +}; + +/* dma_system master ports */ +static struct omap_hwmod_ocp_if *omap44xx_dma_system_masters[] = { + &omap44xx_dma_system__l3_main_2, +}; + +static struct omap_hwmod_addr_space omap44xx_dma_system_addrs[] = { + { + .pa_start = 0x4a056000, + .pa_end = 0x4a0560ff, + .flags = ADDR_TYPE_RT + }, +}; + +/* l4_cfg -> dma_system */ +static struct omap_hwmod_ocp_if omap44xx_l4_cfg__dma_system = { + .master = &omap44xx_l4_cfg_hwmod, + .slave = &omap44xx_dma_system_hwmod, + .clk = "l4_div_ck", + .addr = omap44xx_dma_system_addrs, + .addr_cnt = ARRAY_SIZE(omap44xx_dma_system_addrs), + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + +/* dma_system slave ports */ +static struct omap_hwmod_ocp_if *omap44xx_dma_system_slaves[] = { + &omap44xx_l4_cfg__dma_system, +}; + +static struct omap_hwmod omap44xx_dma_system_hwmod = { + .name = "dma_system", + .class = &omap44xx_dma_hwmod_class, + .mpu_irqs = omap44xx_dma_system_irqs, + .mpu_irqs_cnt = ARRAY_SIZE(omap44xx_dma_system_irqs), + .main_clk = "l3_div_ck", + .prcm = { + .omap4 = { + .clkctrl_reg = OMAP4430_CM_SDMA_SDMA_CLKCTRL, + }, + }, + .slaves = omap44xx_dma_system_slaves, + .slaves_cnt = ARRAY_SIZE(omap44xx_dma_system_slaves), + .masters = omap44xx_dma_system_masters, + .masters_cnt = ARRAY_SIZE(omap44xx_dma_system_masters), + .dev_attr = &dma_dev_attr, + .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP4430), +}; + static __initdata struct omap_hwmod *omap44xx_hwmods[] = { /* dmm class */ &omap44xx_dmm_hwmod, @@ -1391,6 +1489,10 @@ static __initdata struct omap_hwmod *omap44xx_hwmods[] = { &omap44xx_l4_cfg_hwmod, &omap44xx_l4_per_hwmod, &omap44xx_l4_wkup_hwmod, + + /* dma class */ + &omap44xx_dma_system_hwmod, + /* i2c class */ &omap44xx_i2c1_hwmod, &omap44xx_i2c2_hwmod, diff --git a/arch/arm/mach-omap2/omap_opp_data.h b/arch/arm/mach-omap2/omap_opp_data.h new file mode 100644 index 00000000000..46ac27dd6c8 --- /dev/null +++ b/arch/arm/mach-omap2/omap_opp_data.h @@ -0,0 +1,72 @@ +/* + * OMAP SoC specific OPP Data helpers + * + * Copyright (C) 2009-2010 Texas Instruments Incorporated - http://www.ti.com/ + * Nishanth Menon + * Kevin Hilman + * Copyright (C) 2010 Nokia Corporation. + * Eduardo Valentin + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#ifndef __ARCH_ARM_MACH_OMAP2_OMAP_OPP_DATA_H +#define __ARCH_ARM_MACH_OMAP2_OMAP_OPP_DATA_H + +#include <plat/omap_hwmod.h> + +/* + * *BIG FAT WARNING*: + * USE the following ONLY in opp data initialization common to an SoC. + * DO NOT USE these in board files/pm core etc. + */ + +/** + * struct omap_opp_def - OMAP OPP Definition + * @hwmod_name: Name of the hwmod for this domain + * @freq: Frequency in hertz corresponding to this OPP + * @u_volt: Nominal voltage in microvolts corresponding to this OPP + * @default_available: True/false - is this OPP available by default + * + * OMAP SOCs have a standard set of tuples consisting of frequency and voltage + * pairs that the device will support per voltage domain. This is called + * Operating Points or OPP. The actual definitions of OMAP Operating Points + * varies over silicon within the same family of devices. For a specific + * domain, you can have a set of {frequency, voltage} pairs and this is denoted + * by an array of omap_opp_def. As the kernel boots and more information is + * available, a set of these are activated based on the precise nature of + * device the kernel boots up on. It is interesting to remember that each IP + * which belongs to a voltage domain may define their own set of OPPs on top + * of this - but this is handled by the appropriate driver. + */ +struct omap_opp_def { + char *hwmod_name; + + unsigned long freq; + unsigned long u_volt; + + bool default_available; +}; + +/* + * Initialization wrapper used to define an OPP for OMAP variants. + */ +#define OPP_INITIALIZER(_hwmod_name, _enabled, _freq, _uv) \ +{ \ + .hwmod_name = _hwmod_name, \ + .default_available = _enabled, \ + .freq = _freq, \ + .u_volt = _uv, \ +} + +/* Use this to initialize the default table */ +extern int __init omap_init_opp_table(struct omap_opp_def *opp_def, + u32 opp_def_size); + +#endif /* __ARCH_ARM_MACH_OMAP2_OMAP_OPP_DATA_H */ diff --git a/arch/arm/mach-omap2/opp.c b/arch/arm/mach-omap2/opp.c new file mode 100644 index 00000000000..ab8b35b780b --- /dev/null +++ b/arch/arm/mach-omap2/opp.c @@ -0,0 +1,93 @@ +/* + * OMAP SoC specific OPP wrapper function + * + * Copyright (C) 2009-2010 Texas Instruments Incorporated - http://www.ti.com/ + * Nishanth Menon + * Kevin Hilman + * Copyright (C) 2010 Nokia Corporation. + * Eduardo Valentin + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include <linux/module.h> +#include <linux/opp.h> + +#include <plat/omap_device.h> + +#include "omap_opp_data.h" + +/* Temp variable to allow multiple calls */ +static u8 __initdata omap_table_init; + +/** + * omap_init_opp_table() - Initialize opp table as per the CPU type + * @opp_def: opp default list for this silicon + * @opp_def_size: number of opp entries for this silicon + * + * Register the initial OPP table with the OPP library based on the CPU + * type. This is meant to be used only by SoC specific registration. + */ +int __init omap_init_opp_table(struct omap_opp_def *opp_def, + u32 opp_def_size) +{ + int i, r; + + if (!opp_def || !opp_def_size) { + pr_err("%s: invalid params!\n", __func__); + return -EINVAL; + } + + /* + * Initialize only if not already initialized even if the previous + * call failed, because, no reason we'd succeed again. + */ + if (omap_table_init) + return -EEXIST; + omap_table_init = 1; + + /* Lets now register with OPP library */ + for (i = 0; i < opp_def_size; i++) { + struct omap_hwmod *oh; + struct device *dev; + + if (!opp_def->hwmod_name) { + pr_err("%s: NULL name of omap_hwmod, failing [%d].\n", + __func__, i); + return -EINVAL; + } + oh = omap_hwmod_lookup(opp_def->hwmod_name); + if (!oh || !oh->od) { + pr_warn("%s: no hwmod or odev for %s, [%d] " + "cannot add OPPs.\n", __func__, + opp_def->hwmod_name, i); + return -EINVAL; + } + dev = &oh->od->pdev.dev; + + r = opp_add(dev, opp_def->freq, opp_def->u_volt); + if (r) { + dev_err(dev, "%s: add OPP %ld failed for %s [%d] " + "result=%d\n", + __func__, opp_def->freq, + opp_def->hwmod_name, i, r); + } else { + if (!opp_def->default_available) + r = opp_disable(dev, opp_def->freq); + if (r) + dev_err(dev, "%s: disable %ld failed for %s " + "[%d] result=%d\n", + __func__, opp_def->freq, + opp_def->hwmod_name, i, r); + } + opp_def++; + } + + return 0; +} diff --git a/arch/arm/mach-omap2/opp3xxx_data.c b/arch/arm/mach-omap2/opp3xxx_data.c new file mode 100644 index 00000000000..0486fce8a92 --- /dev/null +++ b/arch/arm/mach-omap2/opp3xxx_data.c @@ -0,0 +1,107 @@ +/* + * OMAP3 OPP table definitions. + * + * Copyright (C) 2009-2010 Texas Instruments Incorporated - http://www.ti.com/ + * Nishanth Menon + * Kevin Hilman + * Copyright (C) 2010 Nokia Corporation. + * Eduardo Valentin + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include <linux/module.h> + +#include <plat/cpu.h> + +#include "omap_opp_data.h" + +static struct omap_opp_def __initdata omap34xx_opp_def_list[] = { + /* MPU OPP1 */ + OPP_INITIALIZER("mpu", true, 125000000, 975000), + /* MPU OPP2 */ + OPP_INITIALIZER("mpu", true, 250000000, 1075000), + /* MPU OPP3 */ + OPP_INITIALIZER("mpu", true, 500000000, 1200000), + /* MPU OPP4 */ + OPP_INITIALIZER("mpu", true, 550000000, 1270000), + /* MPU OPP5 */ + OPP_INITIALIZER("mpu", true, 600000000, 1350000), + + /* + * L3 OPP1 - 41.5 MHz is disabled because: The voltage for that OPP is + * almost the same than the one at 83MHz thus providing very little + * gain for the power point of view. In term of energy it will even + * increase the consumption due to the very negative performance + * impact that frequency will do to the MPU and the whole system in + * general. + */ + OPP_INITIALIZER("l3_main", false, 41500000, 975000), + /* L3 OPP2 */ + OPP_INITIALIZER("l3_main", true, 83000000, 1050000), + /* L3 OPP3 */ + OPP_INITIALIZER("l3_main", true, 166000000, 1150000), + + /* DSP OPP1 */ + OPP_INITIALIZER("iva", true, 90000000, 975000), + /* DSP OPP2 */ + OPP_INITIALIZER("iva", true, 180000000, 1075000), + /* DSP OPP3 */ + OPP_INITIALIZER("iva", true, 360000000, 1200000), + /* DSP OPP4 */ + OPP_INITIALIZER("iva", true, 400000000, 1270000), + /* DSP OPP5 */ + OPP_INITIALIZER("iva", true, 430000000, 1350000), +}; + +static struct omap_opp_def __initdata omap36xx_opp_def_list[] = { + /* MPU OPP1 - OPP50 */ + OPP_INITIALIZER("mpu", true, 300000000, 1012500), + /* MPU OPP2 - OPP100 */ + OPP_INITIALIZER("mpu", true, 600000000, 1200000), + /* MPU OPP3 - OPP-Turbo */ + OPP_INITIALIZER("mpu", false, 800000000, 1325000), + /* MPU OPP4 - OPP-SB */ + OPP_INITIALIZER("mpu", false, 1000000000, 1375000), + + /* L3 OPP1 - OPP50 */ + OPP_INITIALIZER("l3_main", true, 100000000, 1000000), + /* L3 OPP2 - OPP100, OPP-Turbo, OPP-SB */ + OPP_INITIALIZER("l3_main", true, 200000000, 1200000), + + /* DSP OPP1 - OPP50 */ + OPP_INITIALIZER("iva", true, 260000000, 1012500), + /* DSP OPP2 - OPP100 */ + OPP_INITIALIZER("iva", true, 520000000, 1200000), + /* DSP OPP3 - OPP-Turbo */ + OPP_INITIALIZER("iva", false, 660000000, 1325000), + /* DSP OPP4 - OPP-SB */ + OPP_INITIALIZER("iva", false, 800000000, 1375000), +}; + +/** + * omap3_opp_init() - initialize omap3 opp table + */ +static int __init omap3_opp_init(void) +{ + int r = -ENODEV; + + if (!cpu_is_omap34xx()) + return r; + + if (cpu_is_omap3630()) + r = omap_init_opp_table(omap36xx_opp_def_list, + ARRAY_SIZE(omap36xx_opp_def_list)); + else + r = omap_init_opp_table(omap34xx_opp_def_list, + ARRAY_SIZE(omap34xx_opp_def_list)); + + return r; +} +device_initcall(omap3_opp_init); diff --git a/arch/arm/mach-omap2/opp4xxx_data.c b/arch/arm/mach-omap2/opp4xxx_data.c new file mode 100644 index 00000000000..a11fa566d8e --- /dev/null +++ b/arch/arm/mach-omap2/opp4xxx_data.c @@ -0,0 +1,57 @@ +/* + * OMAP4 OPP table definitions. + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * Nishanth Menon + * Kevin Hilman + * Thara Gopinath + * Copyright (C) 2010 Nokia Corporation. + * Eduardo Valentin + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include <linux/module.h> + +#include <plat/cpu.h> + +#include "omap_opp_data.h" + +static struct omap_opp_def __initdata omap44xx_opp_def_list[] = { + /* MPU OPP1 - OPP50 */ + OPP_INITIALIZER("mpu", true, 300000000, 1100000), + /* MPU OPP2 - OPP100 */ + OPP_INITIALIZER("mpu", true, 600000000, 1200000), + /* MPU OPP3 - OPP-Turbo */ + OPP_INITIALIZER("mpu", false, 800000000, 1260000), + /* MPU OPP4 - OPP-SB */ + OPP_INITIALIZER("mpu", false, 1008000000, 1350000), + /* L3 OPP1 - OPP50 */ + OPP_INITIALIZER("l3_main_1", true, 100000000, 930000), + /* L3 OPP2 - OPP100, OPP-Turbo, OPP-SB */ + OPP_INITIALIZER("l3_main_1", true, 200000000, 1100000), + /* TODO: add IVA, DSP, aess, fdif, gpu */ +}; + +/** + * omap4_opp_init() - initialize omap4 opp table + */ +static int __init omap4_opp_init(void) +{ + int r = -ENODEV; + + if (!cpu_is_omap44xx()) + return r; + + r = omap_init_opp_table(omap44xx_opp_def_list, + ARRAY_SIZE(omap44xx_opp_def_list)); + + return r; +} +device_initcall(omap4_opp_init); diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 59ca03b0e69..6ec2ee12272 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -143,5 +143,5 @@ static int __init omap2_common_pm_init(void) return 0; } -device_initcall(omap2_common_pm_init); +postcore_initcall(omap2_common_pm_init); diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h index 0d75bfd1fdb..8b4f45eba1b 100644 --- a/arch/arm/mach-omap2/pm.h +++ b/arch/arm/mach-omap2/pm.h @@ -20,6 +20,20 @@ extern int omap3_can_sleep(void); extern int omap_set_pwrdm_state(struct powerdomain *pwrdm, u32 state); extern int omap3_idle_init(void); +#if defined(CONFIG_PM_OPP) +extern int omap3_opp_init(void); +extern int omap4_opp_init(void); +#else +static inline int omap3_opp_init(void) +{ + return -EINVAL; +} +static inline int omap4_opp_init(void) +{ + return -EINVAL; +} +#endif + struct cpuidle_params { u8 valid; u32 sleep_latency; @@ -58,7 +72,7 @@ extern u32 sleep_while_idle; #endif #if defined(CONFIG_CPU_IDLE) -extern void omap3_cpuidle_update_states(void); +extern void omap3_cpuidle_update_states(u32, u32); #endif #if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) @@ -80,9 +94,20 @@ extern void save_secure_ram_context(u32 *addr); extern void omap3_save_scratchpad_contents(void); extern unsigned int omap24xx_idle_loop_suspend_sz; -extern unsigned int omap34xx_suspend_sz; extern unsigned int save_secure_ram_context_sz; extern unsigned int omap24xx_cpu_suspend_sz; extern unsigned int omap34xx_cpu_suspend_sz; +#define PM_RTA_ERRATUM_i608 (1 << 0) +#define PM_SDRC_WAKEUP_ERRATUM_i583 (1 << 1) + +#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3) +extern u16 pm34xx_errata; +#define IS_PM34XX_ERRATUM(id) (pm34xx_errata & (id)) +extern void enable_omap3630_toggle_l2_on_restore(void); +#else +#define IS_PM34XX_ERRATUM(id) 0 +static inline void enable_omap3630_toggle_l2_on_restore(void) { } +#endif /* defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3) */ + #endif diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c index aaeea49b9bd..aea7ced9a2f 100644 --- a/arch/arm/mach-omap2/pm24xx.c +++ b/arch/arm/mach-omap2/pm24xx.c @@ -301,14 +301,8 @@ out: static int omap2_pm_begin(suspend_state_t state) { - suspend_state = state; - return 0; -} - -static int omap2_pm_prepare(void) -{ - /* We cannot sleep in idle until we have resumed */ disable_hlt(); + suspend_state = state; return 0; } @@ -349,21 +343,15 @@ static int omap2_pm_enter(suspend_state_t state) return ret; } -static void omap2_pm_finish(void) -{ - enable_hlt(); -} - static void omap2_pm_end(void) { suspend_state = PM_SUSPEND_ON; + enable_hlt(); } static struct platform_suspend_ops omap_pm_ops = { .begin = omap2_pm_begin, - .prepare = omap2_pm_prepare, .enter = omap2_pm_enter, - .finish = omap2_pm_finish, .end = omap2_pm_end, .valid = suspend_valid_only_mem, }; diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 648b8c50d02..c45b4fa1dee 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -68,6 +68,9 @@ static inline bool is_suspending(void) #define OMAP343X_TABLE_VALUE_OFFSET 0xc0 #define OMAP343X_CONTROL_REG_VALUE_OFFSET 0xc8 +/* pm34xx errata defined in pm.h */ +u16 pm34xx_errata; + struct power_state { struct powerdomain *pwrdm; u32 next_state; @@ -143,7 +146,7 @@ static void omap3_core_save_context(void) /* * Force write last pad into memory, as this can fail in some - * cases according to erratas 1.157, 1.185 + * cases according to errata 1.157, 1.185 */ omap_ctrl_writel(omap_ctrl_readl(OMAP343X_PADCONF_ETK_D14), OMAP343X_CONTROL_MEM_WKUP + 0x2a0); @@ -430,7 +433,7 @@ void omap_sram_idle(void) /* * On EMU/HS devices ROM code restores a SRDC value * from scratchpad which has automatic self refresh on timeout - * of AUTO_CNT = 1 enabled. This takes care of errata 1.142. + * of AUTO_CNT = 1 enabled. This takes care of erratum ID i443. * Hence store/restore the SDRC_POWER register here. */ if (omap_rev() >= OMAP3430_REV_ES3_0 && @@ -529,12 +532,6 @@ out: } #ifdef CONFIG_SUSPEND -static int omap3_pm_prepare(void) -{ - disable_hlt(); - return 0; -} - static int omap3_pm_suspend(void) { struct power_state *pwrst; @@ -597,14 +594,10 @@ static int omap3_pm_enter(suspend_state_t unused) return ret; } -static void omap3_pm_finish(void) -{ - enable_hlt(); -} - /* Hooks to enable / disable UART interrupts during suspend */ static int omap3_pm_begin(suspend_state_t state) { + disable_hlt(); suspend_state = state; omap_uart_enable_irqs(0); return 0; @@ -614,15 +607,14 @@ static void omap3_pm_end(void) { suspend_state = PM_SUSPEND_ON; omap_uart_enable_irqs(1); + enable_hlt(); return; } static struct platform_suspend_ops omap_pm_ops = { .begin = omap3_pm_begin, .end = omap3_pm_end, - .prepare = omap3_pm_prepare, .enter = omap3_pm_enter, - .finish = omap3_pm_finish, .valid = suspend_valid_only_mem, }; #endif /* CONFIG_SUSPEND */ @@ -925,12 +917,29 @@ void omap3_pm_off_mode_enable(int enable) state = PWRDM_POWER_RET; #ifdef CONFIG_CPU_IDLE - omap3_cpuidle_update_states(); + /* + * Erratum i583: implementation for ES rev < Es1.2 on 3630. We cannot + * enable OFF mode in a stable form for previous revisions, restrict + * instead to RET + */ + if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583)) + omap3_cpuidle_update_states(state, PWRDM_POWER_RET); + else + omap3_cpuidle_update_states(state, state); #endif list_for_each_entry(pwrst, &pwrst_list, node) { - pwrst->next_state = state; - omap_set_pwrdm_state(pwrst->pwrdm, state); + if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583) && + pwrst->pwrdm == core_pwrdm && + state == PWRDM_POWER_OFF) { + pwrst->next_state = PWRDM_POWER_RET; + WARN_ONCE(1, + "%s: Core OFF disabled due to errata i583\n", + __func__); + } else { + pwrst->next_state = state; + } + omap_set_pwrdm_state(pwrst->pwrdm, pwrst->next_state); } } @@ -1002,6 +1011,17 @@ void omap_push_sram_idle(void) save_secure_ram_context_sz); } +static void __init pm_errata_configure(void) +{ + if (cpu_is_omap3630()) { + pm34xx_errata |= PM_RTA_ERRATUM_i608; + /* Enable the l2 cache toggling in sleep logic */ + enable_omap3630_toggle_l2_on_restore(); + if (omap_rev() < OMAP3630_REV_ES1_2) + pm34xx_errata |= PM_SDRC_WAKEUP_ERRATUM_i583; + } +} + static int __init omap3_pm_init(void) { struct power_state *pwrst, *tmp; @@ -1011,6 +1031,8 @@ static int __init omap3_pm_init(void) if (!cpu_is_omap34xx()) return -ENODEV; + pm_errata_configure(); + printk(KERN_ERR "Power Management for TI OMAP3.\n"); /* XXX prcm_setup_regs needs to be before enabling hw @@ -1058,6 +1080,14 @@ static int __init omap3_pm_init(void) pm_idle = omap3_pm_idle; omap3_idle_init(); + /* + * RTA is disabled during initialization as per erratum i608 + * it is safer to disable RTA by the bootloader, but we would like + * to be doubly sure here and prevent any mishaps. + */ + if (IS_PM34XX_ERRATUM(PM_RTA_ERRATUM_i608)) + omap3630_ctrl_disable_rta(); + clkdm_add_wkdep(neon_clkdm, mpu_clkdm); if (omap_type() != OMAP2_DEVICE_TYPE_GP) { omap3_secure_ram_storage = diff --git a/arch/arm/mach-omap2/pm44xx.c b/arch/arm/mach-omap2/pm44xx.c index 54544b4fc76..6aff9961e35 100644 --- a/arch/arm/mach-omap2/pm44xx.c +++ b/arch/arm/mach-omap2/pm44xx.c @@ -31,12 +31,6 @@ struct power_state { static LIST_HEAD(pwrst_list); #ifdef CONFIG_SUSPEND -static int omap4_pm_prepare(void) -{ - disable_hlt(); - return 0; -} - static int omap4_pm_suspend(void) { do_wfi(); @@ -59,28 +53,22 @@ static int omap4_pm_enter(suspend_state_t suspend_state) return ret; } -static void omap4_pm_finish(void) -{ - enable_hlt(); - return; -} - static int omap4_pm_begin(suspend_state_t state) { + disable_hlt(); return 0; } static void omap4_pm_end(void) { + enable_hlt(); return; } static struct platform_suspend_ops omap_pm_ops = { .begin = omap4_pm_begin, .end = omap4_pm_end, - .prepare = omap4_pm_prepare, .enter = omap4_pm_enter, - .finish = omap4_pm_finish, .valid = suspend_valid_only_mem, }; #endif /* CONFIG_SUSPEND */ diff --git a/arch/arm/mach-omap2/sdrc.h b/arch/arm/mach-omap2/sdrc.h index 68f57bb67fc..b3f83799e6c 100644 --- a/arch/arm/mach-omap2/sdrc.h +++ b/arch/arm/mach-omap2/sdrc.h @@ -74,5 +74,4 @@ static inline u32 sms_read_reg(u16 reg) */ #define SDRC_MPURATE_LOOPS 96 - #endif diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S index 2fb205a7f28..e3b5cd76c54 100644 --- a/arch/arm/mach-omap2/sleep34xx.S +++ b/arch/arm/mach-omap2/sleep34xx.S @@ -1,6 +1,4 @@ /* - * linux/arch/arm/mach-omap2/sleep.S - * * (C) Copyright 2007 * Texas Instruments * Karthik Dasu <karthik-dp@ti.com> @@ -26,6 +24,7 @@ */ #include <linux/linkage.h> #include <asm/assembler.h> +#include <plat/sram.h> #include <mach/io.h> #include "cm.h" @@ -33,21 +32,27 @@ #include "sdrc.h" #include "control.h" -#define SDRC_SCRATCHPAD_SEM_V 0xfa00291c - -#define PM_PREPWSTST_CORE_V OMAP34XX_PRM_REGADDR(CORE_MOD, \ - OMAP3430_PM_PREPWSTST) -#define PM_PREPWSTST_CORE_P 0x48306AE8 -#define PM_PREPWSTST_MPU_V OMAP34XX_PRM_REGADDR(MPU_MOD, \ - OMAP3430_PM_PREPWSTST) +/* + * Registers access definitions + */ +#define SDRC_SCRATCHPAD_SEM_OFFS 0xc +#define SDRC_SCRATCHPAD_SEM_V OMAP343X_SCRATCHPAD_REGADDR\ + (SDRC_SCRATCHPAD_SEM_OFFS) +#define PM_PREPWSTST_CORE_P OMAP3430_PRM_BASE + CORE_MOD +\ + OMAP3430_PM_PREPWSTST #define PM_PWSTCTRL_MPU_P OMAP3430_PRM_BASE + MPU_MOD + OMAP2_PM_PWSTCTRL #define CM_IDLEST1_CORE_V OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST1) -#define SRAM_BASE_P 0x40200000 -#define CONTROL_STAT 0x480022F0 -#define SCRATCHPAD_MEM_OFFS 0x310 /* Move this as correct place is - * available */ -#define SCRATCHPAD_BASE_P (OMAP343X_CTRL_BASE + OMAP343X_CONTROL_MEM_WKUP\ - + SCRATCHPAD_MEM_OFFS) +#define CM_IDLEST_CKGEN_V OMAP34XX_CM_REGADDR(PLL_MOD, CM_IDLEST) +#define SRAM_BASE_P OMAP3_SRAM_PA +#define CONTROL_STAT OMAP343X_CTRL_BASE + OMAP343X_CONTROL_STATUS +#define CONTROL_MEM_RTA_CTRL (OMAP343X_CTRL_BASE +\ + OMAP36XX_CONTROL_MEM_RTA_CTRL) + +/* Move this as correct place is available */ +#define SCRATCHPAD_MEM_OFFS 0x310 +#define SCRATCHPAD_BASE_P (OMAP343X_CTRL_BASE +\ + OMAP343X_CONTROL_MEM_WKUP +\ + SCRATCHPAD_MEM_OFFS) #define SDRC_POWER_V OMAP34XX_SDRC_REGADDR(SDRC_POWER) #define SDRC_SYSCONFIG_P (OMAP343X_SDRC_BASE + SDRC_SYSCONFIG) #define SDRC_MR_0_P (OMAP343X_SDRC_BASE + SDRC_MR_0) @@ -59,48 +64,38 @@ #define SDRC_DLLA_STATUS_V OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS) #define SDRC_DLLA_CTRL_V OMAP34XX_SDRC_REGADDR(SDRC_DLLA_CTRL) - .text -/* Function to acquire the semaphore in scratchpad */ -ENTRY(lock_scratchpad_sem) - stmfd sp!, {lr} @ save registers on stack -wait_sem: - mov r0,#1 - ldr r1, sdrc_scratchpad_sem -wait_loop: - ldr r2, [r1] @ load the lock value - cmp r2, r0 @ is the lock free ? - beq wait_loop @ not free... - swp r2, r0, [r1] @ semaphore free so lock it and proceed - cmp r2, r0 @ did we succeed ? - beq wait_sem @ no - try again - ldmfd sp!, {pc} @ restore regs and return -sdrc_scratchpad_sem: - .word SDRC_SCRATCHPAD_SEM_V -ENTRY(lock_scratchpad_sem_sz) - .word . - lock_scratchpad_sem - - .text -/* Function to release the scratchpad semaphore */ -ENTRY(unlock_scratchpad_sem) - stmfd sp!, {lr} @ save registers on stack - ldr r3, sdrc_scratchpad_sem - mov r2,#0 - str r2,[r3] - ldmfd sp!, {pc} @ restore regs and return -ENTRY(unlock_scratchpad_sem_sz) - .word . - unlock_scratchpad_sem + +/* + * API functions + */ + +/* + * The "get_*restore_pointer" functions are used to provide a + * physical restore address where the ROM code jumps while waking + * up from MPU OFF/OSWR state. + * The restore pointer is stored into the scratchpad. + */ .text /* Function call to get the restore pointer for resume from OFF */ ENTRY(get_restore_pointer) - stmfd sp!, {lr} @ save registers on stack + stmfd sp!, {lr} @ save registers on stack adr r0, restore - ldmfd sp!, {pc} @ restore regs and return + ldmfd sp!, {pc} @ restore regs and return ENTRY(get_restore_pointer_sz) - .word . - get_restore_pointer + .word . - get_restore_pointer .text -/* Function call to get the restore pointer for for ES3 to resume from OFF */ +/* Function call to get the restore pointer for 3630 resume from OFF */ +ENTRY(get_omap3630_restore_pointer) + stmfd sp!, {lr} @ save registers on stack + adr r0, restore_3630 + ldmfd sp!, {pc} @ restore regs and return +ENTRY(get_omap3630_restore_pointer_sz) + .word . - get_omap3630_restore_pointer + + .text +/* Function call to get the restore pointer for ES3 to resume from OFF */ ENTRY(get_es3_restore_pointer) stmfd sp!, {lr} @ save registers on stack adr r0, restore_es3 @@ -108,54 +103,23 @@ ENTRY(get_es3_restore_pointer) ENTRY(get_es3_restore_pointer_sz) .word . - get_es3_restore_pointer -ENTRY(es3_sdrc_fix) - ldr r4, sdrc_syscfg @ get config addr - ldr r5, [r4] @ get value - tst r5, #0x100 @ is part access blocked - it eq - biceq r5, r5, #0x100 @ clear bit if set - str r5, [r4] @ write back change - ldr r4, sdrc_mr_0 @ get config addr - ldr r5, [r4] @ get value - str r5, [r4] @ write back change - ldr r4, sdrc_emr2_0 @ get config addr - ldr r5, [r4] @ get value - str r5, [r4] @ write back change - ldr r4, sdrc_manual_0 @ get config addr - mov r5, #0x2 @ autorefresh command - str r5, [r4] @ kick off refreshes - ldr r4, sdrc_mr_1 @ get config addr - ldr r5, [r4] @ get value - str r5, [r4] @ write back change - ldr r4, sdrc_emr2_1 @ get config addr - ldr r5, [r4] @ get value - str r5, [r4] @ write back change - ldr r4, sdrc_manual_1 @ get config addr - mov r5, #0x2 @ autorefresh command - str r5, [r4] @ kick off refreshes - bx lr -sdrc_syscfg: - .word SDRC_SYSCONFIG_P -sdrc_mr_0: - .word SDRC_MR_0_P -sdrc_emr2_0: - .word SDRC_EMR2_0_P -sdrc_manual_0: - .word SDRC_MANUAL_0_P -sdrc_mr_1: - .word SDRC_MR_1_P -sdrc_emr2_1: - .word SDRC_EMR2_1_P -sdrc_manual_1: - .word SDRC_MANUAL_1_P -ENTRY(es3_sdrc_fix_sz) - .word . - es3_sdrc_fix + .text +/* + * L2 cache needs to be toggled for stable OFF mode functionality on 3630. + * This function sets up a flag that will allow for this toggling to take + * place on 3630. Hopefully some version in the future may not need this. + */ +ENTRY(enable_omap3630_toggle_l2_on_restore) + stmfd sp!, {lr} @ save registers on stack + /* Setup so that we will disable and enable l2 */ + mov r1, #0x1 + str r1, l2dis_3630 + ldmfd sp!, {pc} @ restore regs and return + .text /* Function to call rom code to save secure ram context */ ENTRY(save_secure_ram_context) stmfd sp!, {r1-r12, lr} @ save registers on stack -save_secure_ram_debug: - /* b save_secure_ram_debug */ @ enable to debug save code adr r3, api_params @ r3 points to parameters str r0, [r3,#0x4] @ r0 has sdram address ldr r12, high_mask @@ -185,35 +149,162 @@ ENTRY(save_secure_ram_context_sz) .word . - save_secure_ram_context /* + * ====================== + * == Idle entry point == + * ====================== + */ + +/* * Forces OMAP into idle state * - * omap34xx_suspend() - This bit of code just executes the WFI - * for normal idles. + * omap34xx_cpu_suspend() - This bit of code saves the CPU context if needed + * and executes the WFI instruction. Calling WFI effectively changes the + * power domains states to the desired target power states. + * * - * Note: This code get's copied to internal SRAM at boot. When the OMAP - * wakes up it continues execution at the point it went to sleep. + * Notes: + * - this code gets copied to internal SRAM at boot and after wake-up + * from OFF mode. The execution pointer in SRAM is _omap_sram_idle. + * - when the OMAP wakes up it continues at different execution points + * depending on the low power mode (non-OFF vs OFF modes), + * cf. 'Resume path for xxx mode' comments. */ ENTRY(omap34xx_cpu_suspend) - stmfd sp!, {r0-r12, lr} @ save registers on stack -loop: - /*b loop*/ @Enable to debug by stepping through code - /* r0 contains restore pointer in sdram */ - /* r1 contains information about saving context */ - ldr r4, sdrc_power @ read the SDRC_POWER register - ldr r5, [r4] @ read the contents of SDRC_POWER - orr r5, r5, #0x40 @ enable self refresh on idle req - str r5, [r4] @ write back to SDRC_POWER register + stmfd sp!, {r0-r12, lr} @ save registers on stack + /* + * r0 contains restore pointer in sdram + * r1 contains information about saving context: + * 0 - No context lost + * 1 - Only L1 and logic lost + * 2 - Only L2 lost + * 3 - Both L1 and L2 lost + */ + + /* Directly jump to WFI is the context save is not required */ cmp r1, #0x0 - /* If context save is required, do that and execute wfi */ - bne save_context_wfi + beq omap3_do_wfi + + /* Otherwise fall through to the save context code */ +save_context_wfi: + mov r8, r0 @ Store SDRAM address in r8 + mrc p15, 0, r5, c1, c0, 1 @ Read Auxiliary Control Register + mov r4, #0x1 @ Number of parameters for restore call + stmia r8!, {r4-r5} @ Push parameters for restore call + mrc p15, 1, r5, c9, c0, 2 @ Read L2 AUX ctrl register + stmia r8!, {r4-r5} @ Push parameters for restore call + + /* Check what that target sleep state is from r1 */ + cmp r1, #0x2 @ Only L2 lost, no need to save context + beq clean_caches + +l1_logic_lost: + /* Store sp and spsr to SDRAM */ + mov r4, sp + mrs r5, spsr + mov r6, lr + stmia r8!, {r4-r6} + /* Save all ARM registers */ + /* Coprocessor access control register */ + mrc p15, 0, r6, c1, c0, 2 + stmia r8!, {r6} + /* TTBR0, TTBR1 and Translation table base control */ + mrc p15, 0, r4, c2, c0, 0 + mrc p15, 0, r5, c2, c0, 1 + mrc p15, 0, r6, c2, c0, 2 + stmia r8!, {r4-r6} + /* + * Domain access control register, data fault status register, + * and instruction fault status register + */ + mrc p15, 0, r4, c3, c0, 0 + mrc p15, 0, r5, c5, c0, 0 + mrc p15, 0, r6, c5, c0, 1 + stmia r8!, {r4-r6} + /* + * Data aux fault status register, instruction aux fault status, + * data fault address register and instruction fault address register + */ + mrc p15, 0, r4, c5, c1, 0 + mrc p15, 0, r5, c5, c1, 1 + mrc p15, 0, r6, c6, c0, 0 + mrc p15, 0, r7, c6, c0, 2 + stmia r8!, {r4-r7} + /* + * user r/w thread and process ID, user r/o thread and process ID, + * priv only thread and process ID, cache size selection + */ + mrc p15, 0, r4, c13, c0, 2 + mrc p15, 0, r5, c13, c0, 3 + mrc p15, 0, r6, c13, c0, 4 + mrc p15, 2, r7, c0, c0, 0 + stmia r8!, {r4-r7} + /* Data TLB lockdown, instruction TLB lockdown registers */ + mrc p15, 0, r5, c10, c0, 0 + mrc p15, 0, r6, c10, c0, 1 + stmia r8!, {r5-r6} + /* Secure or non secure vector base address, FCSE PID, Context PID*/ + mrc p15, 0, r4, c12, c0, 0 + mrc p15, 0, r5, c13, c0, 0 + mrc p15, 0, r6, c13, c0, 1 + stmia r8!, {r4-r6} + /* Primary remap, normal remap registers */ + mrc p15, 0, r4, c10, c2, 0 + mrc p15, 0, r5, c10, c2, 1 + stmia r8!,{r4-r5} + + /* Store current cpsr*/ + mrs r2, cpsr + stmia r8!, {r2} + + mrc p15, 0, r4, c1, c0, 0 + /* save control register */ + stmia r8!, {r4} + +clean_caches: + /* + * Clean Data or unified cache to POU + * How to invalidate only L1 cache???? - #FIX_ME# + * mcr p15, 0, r11, c7, c11, 1 + */ + cmp r1, #0x1 @ Check whether L2 inval is required + beq omap3_do_wfi + +clean_l2: + /* + * jump out to kernel flush routine + * - reuse that code is better + * - it executes in a cached space so is faster than refetch per-block + * - should be faster and will change with kernel + * - 'might' have to copy address, load and jump to it + */ + ldr r1, kernel_flush + mov lr, pc + bx r1 + +omap3_do_wfi: + ldr r4, sdrc_power @ read the SDRC_POWER register + ldr r5, [r4] @ read the contents of SDRC_POWER + orr r5, r5, #0x40 @ enable self refresh on idle req + str r5, [r4] @ write back to SDRC_POWER register + /* Data memory barrier and Data sync barrier */ mov r1, #0 mcr p15, 0, r1, c7, c10, 4 mcr p15, 0, r1, c7, c10, 5 +/* + * =================================== + * == WFI instruction => Enter idle == + * =================================== + */ wfi @ wait for interrupt +/* + * =================================== + * == Resume path for non-OFF modes == + * =================================== + */ nop nop nop @@ -226,9 +317,30 @@ loop: nop bl wait_sdrc_ok - ldmfd sp!, {r0-r12, pc} @ restore regs and return +/* + * =================================== + * == Exit point from non-OFF modes == + * =================================== + */ + ldmfd sp!, {r0-r12, pc} @ restore regs and return + + +/* + * ============================== + * == Resume path for OFF mode == + * ============================== + */ + +/* + * The restore_* functions are called by the ROM code + * when back from WFI in OFF mode. + * Cf. the get_*restore_pointer functions. + * + * restore_es3: applies to 34xx >= ES3.0 + * restore_3630: applies to 36xx + * restore: common code for 3xxx + */ restore_es3: - /*b restore_es3*/ @ Enable to debug restore code ldr r5, pm_prepwstst_core_p ldr r4, [r5] and r4, r4, #0x3 @@ -245,82 +357,117 @@ copy_to_sram: bne copy_to_sram ldr r1, sram_base blx r1 + b restore + +restore_3630: + ldr r1, pm_prepwstst_core_p + ldr r2, [r1] + and r2, r2, #0x3 + cmp r2, #0x0 @ Check if previous power state of CORE is OFF + bne restore + /* Disable RTA before giving control */ + ldr r1, control_mem_rta + mov r2, #OMAP36XX_RTA_DISABLE + str r2, [r1] + + /* Fall through to common code for the remaining logic */ + restore: - /* b restore*/ @ Enable to debug restore code - /* Check what was the reason for mpu reset and store the reason in r9*/ - /* 1 - Only L1 and logic lost */ - /* 2 - Only L2 lost - In this case, we wont be here */ - /* 3 - Both L1 and L2 lost */ - ldr r1, pm_pwstctrl_mpu + /* + * Check what was the reason for mpu reset and store the reason in r9: + * 0 - No context lost + * 1 - Only L1 and logic lost + * 2 - Only L2 lost - In this case, we wont be here + * 3 - Both L1 and L2 lost + */ + ldr r1, pm_pwstctrl_mpu ldr r2, [r1] - and r2, r2, #0x3 - cmp r2, #0x0 @ Check if target power state was OFF or RET - moveq r9, #0x3 @ MPU OFF => L1 and L2 lost + and r2, r2, #0x3 + cmp r2, #0x0 @ Check if target power state was OFF or RET + moveq r9, #0x3 @ MPU OFF => L1 and L2 lost movne r9, #0x1 @ Only L1 and L2 lost => avoid L2 invalidation bne logic_l1_restore + + ldr r0, l2dis_3630 + cmp r0, #0x1 @ should we disable L2 on 3630? + bne skipl2dis + mrc p15, 0, r0, c1, c0, 1 + bic r0, r0, #2 @ disable L2 cache + mcr p15, 0, r0, c1, c0, 1 +skipl2dis: ldr r0, control_stat ldr r1, [r0] and r1, #0x700 cmp r1, #0x300 beq l2_inv_gp - mov r0, #40 @ set service ID for PPA - mov r12, r0 @ copy secure Service ID in r12 - mov r1, #0 @ set task id for ROM code in r1 - mov r2, #4 @ set some flags in r2, r6 + mov r0, #40 @ set service ID for PPA + mov r12, r0 @ copy secure Service ID in r12 + mov r1, #0 @ set task id for ROM code in r1 + mov r2, #4 @ set some flags in r2, r6 mov r6, #0xff adr r3, l2_inv_api_params @ r3 points to dummy parameters mcr p15, 0, r0, c7, c10, 4 @ data write barrier mcr p15, 0, r0, c7, c10, 5 @ data memory barrier .word 0xE1600071 @ call SMI monitor (smi #1) /* Write to Aux control register to set some bits */ - mov r0, #42 @ set service ID for PPA - mov r12, r0 @ copy secure Service ID in r12 - mov r1, #0 @ set task id for ROM code in r1 - mov r2, #4 @ set some flags in r2, r6 + mov r0, #42 @ set service ID for PPA + mov r12, r0 @ copy secure Service ID in r12 + mov r1, #0 @ set task id for ROM code in r1 + mov r2, #4 @ set some flags in r2, r6 mov r6, #0xff ldr r4, scratchpad_base - ldr r3, [r4, #0xBC] @ r3 points to parameters + ldr r3, [r4, #0xBC] @ r3 points to parameters mcr p15, 0, r0, c7, c10, 4 @ data write barrier mcr p15, 0, r0, c7, c10, 5 @ data memory barrier .word 0xE1600071 @ call SMI monitor (smi #1) #ifdef CONFIG_OMAP3_L2_AUX_SECURE_SAVE_RESTORE /* Restore L2 aux control register */ - @ set service ID for PPA + @ set service ID for PPA mov r0, #CONFIG_OMAP3_L2_AUX_SECURE_SERVICE_SET_ID - mov r12, r0 @ copy service ID in r12 - mov r1, #0 @ set task ID for ROM code in r1 - mov r2, #4 @ set some flags in r2, r6 + mov r12, r0 @ copy service ID in r12 + mov r1, #0 @ set task ID for ROM code in r1 + mov r2, #4 @ set some flags in r2, r6 mov r6, #0xff ldr r4, scratchpad_base ldr r3, [r4, #0xBC] - adds r3, r3, #8 @ r3 points to parameters + adds r3, r3, #8 @ r3 points to parameters mcr p15, 0, r0, c7, c10, 4 @ data write barrier mcr p15, 0, r0, c7, c10, 5 @ data memory barrier .word 0xE1600071 @ call SMI monitor (smi #1) #endif b logic_l1_restore + l2_inv_api_params: - .word 0x1, 0x00 + .word 0x1, 0x00 l2_inv_gp: /* Execute smi to invalidate L2 cache */ - mov r12, #0x1 @ set up to invalide L2 -smi: .word 0xE1600070 @ Call SMI monitor (smieq) + mov r12, #0x1 @ set up to invalidate L2 + .word 0xE1600070 @ Call SMI monitor (smieq) /* Write to Aux control register to set some bits */ ldr r4, scratchpad_base ldr r3, [r4,#0xBC] ldr r0, [r3,#4] mov r12, #0x3 - .word 0xE1600070 @ Call SMI monitor (smieq) + .word 0xE1600070 @ Call SMI monitor (smieq) ldr r4, scratchpad_base ldr r3, [r4,#0xBC] ldr r0, [r3,#12] mov r12, #0x2 - .word 0xE1600070 @ Call SMI monitor (smieq) + .word 0xE1600070 @ Call SMI monitor (smieq) logic_l1_restore: + ldr r1, l2dis_3630 + cmp r1, #0x1 @ Test if L2 re-enable needed on 3630 + bne skipl2reen + mrc p15, 0, r1, c1, c0, 1 + orr r1, r1, #2 @ re-enable L2 cache + mcr p15, 0, r1, c1, c0, 1 +skipl2reen: mov r1, #0 - /* Invalidate all instruction caches to PoU - * and flush branch target cache */ + /* + * Invalidate all instruction caches to PoU + * and flush branch target cache + */ mcr p15, 0, r1, c7, c5, 0 ldr r4, scratchpad_base @@ -341,33 +488,33 @@ logic_l1_restore: MCR p15, 0, r6, c2, c0, 1 /* Translation table base control register */ MCR p15, 0, r7, c2, c0, 2 - /*domain access Control Register */ + /* Domain access Control Register */ MCR p15, 0, r8, c3, c0, 0 - /* data fault status Register */ + /* Data fault status Register */ MCR p15, 0, r9, c5, c0, 0 - ldmia r3!,{r4-r8} - /* instruction fault status Register */ + ldmia r3!,{r4-r8} + /* Instruction fault status Register */ MCR p15, 0, r4, c5, c0, 1 - /*Data Auxiliary Fault Status Register */ + /* Data Auxiliary Fault Status Register */ MCR p15, 0, r5, c5, c1, 0 - /*Instruction Auxiliary Fault Status Register*/ + /* Instruction Auxiliary Fault Status Register*/ MCR p15, 0, r6, c5, c1, 1 - /*Data Fault Address Register */ + /* Data Fault Address Register */ MCR p15, 0, r7, c6, c0, 0 - /*Instruction Fault Address Register*/ + /* Instruction Fault Address Register*/ MCR p15, 0, r8, c6, c0, 2 - ldmia r3!,{r4-r7} + ldmia r3!,{r4-r7} - /* user r/w thread and process ID */ + /* User r/w thread and process ID */ MCR p15, 0, r4, c13, c0, 2 - /* user ro thread and process ID */ + /* User ro thread and process ID */ MCR p15, 0, r5, c13, c0, 3 - /*Privileged only thread and process ID */ + /* Privileged only thread and process ID */ MCR p15, 0, r6, c13, c0, 4 - /* cache size selection */ + /* Cache size selection */ MCR p15, 2, r7, c0, c0, 0 - ldmia r3!,{r4-r8} + ldmia r3!,{r4-r8} /* Data TLB lockdown registers */ MCR p15, 0, r4, c10, c0, 0 /* Instruction TLB lockdown registers */ @@ -379,26 +526,27 @@ logic_l1_restore: /* Context PID */ MCR p15, 0, r8, c13, c0, 1 - ldmia r3!,{r4-r5} - /* primary memory remap register */ + ldmia r3!,{r4-r5} + /* Primary memory remap register */ MCR p15, 0, r4, c10, c2, 0 - /*normal memory remap register */ + /* Normal memory remap register */ MCR p15, 0, r5, c10, c2, 1 /* Restore cpsr */ - ldmia r3!,{r4} /*load CPSR from SDRAM*/ - msr cpsr, r4 /*store cpsr */ + ldmia r3!,{r4} @ load CPSR from SDRAM + msr cpsr, r4 @ store cpsr /* Enabling MMU here */ - mrc p15, 0, r7, c2, c0, 2 /* Read TTBRControl */ - /* Extract N (0:2) bits and decide whether to use TTBR0 or TTBR1*/ + mrc p15, 0, r7, c2, c0, 2 @ Read TTBRControl + /* Extract N (0:2) bits and decide whether to use TTBR0 or TTBR1 */ and r7, #0x7 cmp r7, #0x0 beq usettbr0 ttbr_error: - /* More work needs to be done to support N[0:2] value other than 0 - * So looping here so that the error can be detected - */ + /* + * More work needs to be done to support N[0:2] value other than 0 + * So looping here so that the error can be detected + */ b ttbr_error usettbr0: mrc p15, 0, r2, c2, c0, 0 @@ -406,21 +554,25 @@ usettbr0: and r2, r5 mov r4, pc ldr r5, table_index_mask - and r4, r5 /* r4 = 31 to 20 bits of pc */ + and r4, r5 @ r4 = 31 to 20 bits of pc /* Extract the value to be written to table entry */ ldr r1, table_entry - add r1, r1, r4 /* r1 has value to be written to table entry*/ + /* r1 has the value to be written to table entry*/ + add r1, r1, r4 /* Getting the address of table entry to modify */ lsr r4, #18 - add r2, r4 /* r2 has the location which needs to be modified */ + /* r2 has the location which needs to be modified */ + add r2, r4 /* Storing previous entry of location being modified */ ldr r5, scratchpad_base ldr r4, [r2] str r4, [r5, #0xC0] /* Modify the table entry */ str r1, [r2] - /* Storing address of entry being modified - * - will be restored after enabling MMU */ + /* + * Storing address of entry being modified + * - will be restored after enabling MMU + */ ldr r5, scratchpad_base str r2, [r5, #0xC4] @@ -429,8 +581,11 @@ usettbr0: mcr p15, 0, r0, c7, c5, 6 @ Invalidate branch predictor array mcr p15, 0, r0, c8, c5, 0 @ Invalidate instruction TLB mcr p15, 0, r0, c8, c6, 0 @ Invalidate data TLB - /* Restore control register but dont enable caches here*/ - /* Caches will be enabled after restoring MMU table entry */ + /* + * Restore control register. This enables the MMU. + * The caches and prediction are not enabled here, they + * will be enabled after restoring the MMU table entry. + */ ldmia r3!, {r4} /* Store previous value of control register in scratchpad */ str r4, [r5, #0xC8] @@ -438,212 +593,144 @@ usettbr0: and r4, r2 mcr p15, 0, r4, c1, c0, 0 - ldmfd sp!, {r0-r12, pc} @ restore regs and return -save_context_wfi: - /*b save_context_wfi*/ @ enable to debug save code - mov r8, r0 /* Store SDRAM address in r8 */ - mrc p15, 0, r5, c1, c0, 1 @ Read Auxiliary Control Register - mov r4, #0x1 @ Number of parameters for restore call - stmia r8!, {r4-r5} @ Push parameters for restore call - mrc p15, 1, r5, c9, c0, 2 @ Read L2 AUX ctrl register - stmia r8!, {r4-r5} @ Push parameters for restore call - /* Check what that target sleep state is:stored in r1*/ - /* 1 - Only L1 and logic lost */ - /* 2 - Only L2 lost */ - /* 3 - Both L1 and L2 lost */ - cmp r1, #0x2 /* Only L2 lost */ - beq clean_l2 - cmp r1, #0x1 /* L2 retained */ - /* r9 stores whether to clean L2 or not*/ - moveq r9, #0x0 /* Dont Clean L2 */ - movne r9, #0x1 /* Clean L2 */ -l1_logic_lost: - /* Store sp and spsr to SDRAM */ - mov r4, sp - mrs r5, spsr - mov r6, lr - stmia r8!, {r4-r6} - /* Save all ARM registers */ - /* Coprocessor access control register */ - mrc p15, 0, r6, c1, c0, 2 - stmia r8!, {r6} - /* TTBR0, TTBR1 and Translation table base control */ - mrc p15, 0, r4, c2, c0, 0 - mrc p15, 0, r5, c2, c0, 1 - mrc p15, 0, r6, c2, c0, 2 - stmia r8!, {r4-r6} - /* Domain access control register, data fault status register, - and instruction fault status register */ - mrc p15, 0, r4, c3, c0, 0 - mrc p15, 0, r5, c5, c0, 0 - mrc p15, 0, r6, c5, c0, 1 - stmia r8!, {r4-r6} - /* Data aux fault status register, instruction aux fault status, - datat fault address register and instruction fault address register*/ - mrc p15, 0, r4, c5, c1, 0 - mrc p15, 0, r5, c5, c1, 1 - mrc p15, 0, r6, c6, c0, 0 - mrc p15, 0, r7, c6, c0, 2 - stmia r8!, {r4-r7} - /* user r/w thread and process ID, user r/o thread and process ID, - priv only thread and process ID, cache size selection */ - mrc p15, 0, r4, c13, c0, 2 - mrc p15, 0, r5, c13, c0, 3 - mrc p15, 0, r6, c13, c0, 4 - mrc p15, 2, r7, c0, c0, 0 - stmia r8!, {r4-r7} - /* Data TLB lockdown, instruction TLB lockdown registers */ - mrc p15, 0, r5, c10, c0, 0 - mrc p15, 0, r6, c10, c0, 1 - stmia r8!, {r5-r6} - /* Secure or non secure vector base address, FCSE PID, Context PID*/ - mrc p15, 0, r4, c12, c0, 0 - mrc p15, 0, r5, c13, c0, 0 - mrc p15, 0, r6, c13, c0, 1 - stmia r8!, {r4-r6} - /* Primary remap, normal remap registers */ - mrc p15, 0, r4, c10, c2, 0 - mrc p15, 0, r5, c10, c2, 1 - stmia r8!,{r4-r5} +/* + * ============================== + * == Exit point from OFF mode == + * ============================== + */ + ldmfd sp!, {r0-r12, pc} @ restore regs and return - /* Store current cpsr*/ - mrs r2, cpsr - stmia r8!, {r2} - mrc p15, 0, r4, c1, c0, 0 - /* save control register */ - stmia r8!, {r4} -clean_caches: - /* Clean Data or unified cache to POU*/ - /* How to invalidate only L1 cache???? - #FIX_ME# */ - /* mcr p15, 0, r11, c7, c11, 1 */ - cmp r9, #1 /* Check whether L2 inval is required or not*/ - bne skip_l2_inval -clean_l2: - /* read clidr */ - mrc p15, 1, r0, c0, c0, 1 - /* extract loc from clidr */ - ands r3, r0, #0x7000000 - /* left align loc bit field */ - mov r3, r3, lsr #23 - /* if loc is 0, then no need to clean */ - beq finished - /* start clean at cache level 0 */ - mov r10, #0 -loop1: - /* work out 3x current cache level */ - add r2, r10, r10, lsr #1 - /* extract cache type bits from clidr*/ - mov r1, r0, lsr r2 - /* mask of the bits for current cache only */ - and r1, r1, #7 - /* see what cache we have at this level */ - cmp r1, #2 - /* skip if no cache, or just i-cache */ - blt skip - /* select current cache level in cssr */ - mcr p15, 2, r10, c0, c0, 0 - /* isb to sych the new cssr&csidr */ - isb - /* read the new csidr */ - mrc p15, 1, r1, c0, c0, 0 - /* extract the length of the cache lines */ - and r2, r1, #7 - /* add 4 (line length offset) */ - add r2, r2, #4 - ldr r4, assoc_mask - /* find maximum number on the way size */ - ands r4, r4, r1, lsr #3 - /* find bit position of way size increment */ - clz r5, r4 - ldr r7, numset_mask - /* extract max number of the index size*/ - ands r7, r7, r1, lsr #13 -loop2: - mov r9, r4 - /* create working copy of max way size*/ -loop3: - /* factor way and cache number into r11 */ - orr r11, r10, r9, lsl r5 - /* factor index number into r11 */ - orr r11, r11, r7, lsl r2 - /*clean & invalidate by set/way */ - mcr p15, 0, r11, c7, c10, 2 - /* decrement the way*/ - subs r9, r9, #1 - bge loop3 - /*decrement the index */ - subs r7, r7, #1 - bge loop2 -skip: - add r10, r10, #2 - /* increment cache number */ - cmp r3, r10 - bgt loop1 -finished: - /*swith back to cache level 0 */ - mov r10, #0 - /* select current cache level in cssr */ - mcr p15, 2, r10, c0, c0, 0 - isb -skip_l2_inval: - /* Data memory barrier and Data sync barrier */ - mov r1, #0 - mcr p15, 0, r1, c7, c10, 4 - mcr p15, 0, r1, c7, c10, 5 +/* + * Internal functions + */ - wfi @ wait for interrupt - nop - nop - nop - nop - nop - nop - nop - nop - nop - nop - bl wait_sdrc_ok - /* restore regs and return */ - ldmfd sp!, {r0-r12, pc} +/* This function implements the erratum ID i443 WA, applies to 34xx >= ES3.0 */ + .text +ENTRY(es3_sdrc_fix) + ldr r4, sdrc_syscfg @ get config addr + ldr r5, [r4] @ get value + tst r5, #0x100 @ is part access blocked + it eq + biceq r5, r5, #0x100 @ clear bit if set + str r5, [r4] @ write back change + ldr r4, sdrc_mr_0 @ get config addr + ldr r5, [r4] @ get value + str r5, [r4] @ write back change + ldr r4, sdrc_emr2_0 @ get config addr + ldr r5, [r4] @ get value + str r5, [r4] @ write back change + ldr r4, sdrc_manual_0 @ get config addr + mov r5, #0x2 @ autorefresh command + str r5, [r4] @ kick off refreshes + ldr r4, sdrc_mr_1 @ get config addr + ldr r5, [r4] @ get value + str r5, [r4] @ write back change + ldr r4, sdrc_emr2_1 @ get config addr + ldr r5, [r4] @ get value + str r5, [r4] @ write back change + ldr r4, sdrc_manual_1 @ get config addr + mov r5, #0x2 @ autorefresh command + str r5, [r4] @ kick off refreshes + bx lr + +sdrc_syscfg: + .word SDRC_SYSCONFIG_P +sdrc_mr_0: + .word SDRC_MR_0_P +sdrc_emr2_0: + .word SDRC_EMR2_0_P +sdrc_manual_0: + .word SDRC_MANUAL_0_P +sdrc_mr_1: + .word SDRC_MR_1_P +sdrc_emr2_1: + .word SDRC_EMR2_1_P +sdrc_manual_1: + .word SDRC_MANUAL_1_P +ENTRY(es3_sdrc_fix_sz) + .word . - es3_sdrc_fix + +/* + * This function implements the erratum ID i581 WA: + * SDRC state restore before accessing the SDRAM + * + * Only used at return from non-OFF mode. For OFF + * mode the ROM code configures the SDRC and + * the DPLL before calling the restore code directly + * from DDR. + */ /* Make sure SDRC accesses are ok */ wait_sdrc_ok: - ldr r4, cm_idlest1_core - ldr r5, [r4] - and r5, r5, #0x2 - cmp r5, #0 - bne wait_sdrc_ok - ldr r4, sdrc_power - ldr r5, [r4] - bic r5, r5, #0x40 - str r5, [r4] + +/* DPLL3 must be locked before accessing the SDRC. Maybe the HW ensures this */ + ldr r4, cm_idlest_ckgen +wait_dpll3_lock: + ldr r5, [r4] + tst r5, #1 + beq wait_dpll3_lock + + ldr r4, cm_idlest1_core +wait_sdrc_ready: + ldr r5, [r4] + tst r5, #0x2 + bne wait_sdrc_ready + /* allow DLL powerdown upon hw idle req */ + ldr r4, sdrc_power + ldr r5, [r4] + bic r5, r5, #0x40 + str r5, [r4] + +is_dll_in_lock_mode: + /* Is dll in lock mode? */ + ldr r4, sdrc_dlla_ctrl + ldr r5, [r4] + tst r5, #0x4 + bxne lr @ Return if locked + /* wait till dll locks */ +wait_dll_lock_timed: + ldr r4, wait_dll_lock_counter + add r4, r4, #1 + str r4, wait_dll_lock_counter + ldr r4, sdrc_dlla_status + /* Wait 20uS for lock */ + mov r6, #8 wait_dll_lock: - /* Is dll in lock mode? */ - ldr r4, sdrc_dlla_ctrl - ldr r5, [r4] - tst r5, #0x4 - bxne lr - /* wait till dll locks */ - ldr r4, sdrc_dlla_status - ldr r5, [r4] - and r5, r5, #0x4 - cmp r5, #0x4 - bne wait_dll_lock - bx lr + subs r6, r6, #0x1 + beq kick_dll + ldr r5, [r4] + and r5, r5, #0x4 + cmp r5, #0x4 + bne wait_dll_lock + bx lr @ Return when locked + + /* disable/reenable DLL if not locked */ +kick_dll: + ldr r4, sdrc_dlla_ctrl + ldr r5, [r4] + mov r6, r5 + bic r6, #(1<<3) @ disable dll + str r6, [r4] + dsb + orr r6, r6, #(1<<3) @ enable dll + str r6, [r4] + dsb + ldr r4, kick_counter + add r4, r4, #1 + str r4, kick_counter + b wait_dll_lock_timed cm_idlest1_core: .word CM_IDLEST1_CORE_V +cm_idlest_ckgen: + .word CM_IDLEST_CKGEN_V sdrc_dlla_status: .word SDRC_DLLA_STATUS_V sdrc_dlla_ctrl: .word SDRC_DLLA_CTRL_V -pm_prepwstst_core: - .word PM_PREPWSTST_CORE_V pm_prepwstst_core_p: .word PM_PREPWSTST_CORE_P -pm_prepwstst_mpu: - .word PM_PREPWSTST_MPU_V pm_pwstctrl_mpu: .word PM_PWSTCTRL_MPU_P scratchpad_base: @@ -651,13 +738,7 @@ scratchpad_base: sram_base: .word SRAM_BASE_P + 0x8000 sdrc_power: - .word SDRC_POWER_V -clk_stabilize_delay: - .word 0x000001FF -assoc_mask: - .word 0x3ff -numset_mask: - .word 0x7fff + .word SDRC_POWER_V ttbrbit_mask: .word 0xFFFFC000 table_index_mask: @@ -668,5 +749,20 @@ cache_pred_disable_mask: .word 0xFFFFE7FB control_stat: .word CONTROL_STAT +control_mem_rta: + .word CONTROL_MEM_RTA_CTRL +kernel_flush: + .word v7_flush_dcache_all +l2dis_3630: + .word 0 + /* + * When exporting to userspace while the counters are in SRAM, + * these 2 words need to be at the end to facilitate retrival! + */ +kick_counter: + .word 0 +wait_dll_lock_counter: + .word 0 + ENTRY(omap34xx_cpu_suspend_sz) .word . - omap34xx_cpu_suspend diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig index fa2e5bffbb8..6983cb4d4ca 100644 --- a/arch/arm/mach-s3c2412/Kconfig +++ b/arch/arm/mach-s3c2412/Kconfig @@ -28,9 +28,16 @@ config S3C2412_DMA config S3C2412_PM bool + select S3C2412_PM_SLEEP help Internal config node to apply S3C2412 power management +config S3C2412_PM_SLEEP + bool + help + Internal config node to apply sleep for S3C2412 power management. + Can be selected by another SoCs with similar sleep procedure. + # Note, the S3C2412 IOtiming support is in plat-s3c24xx config S3C2412_CPUFREQ diff --git a/arch/arm/mach-s3c2412/Makefile b/arch/arm/mach-s3c2412/Makefile index 530ec46cbae..6c48a91ea39 100644 --- a/arch/arm/mach-s3c2412/Makefile +++ b/arch/arm/mach-s3c2412/Makefile @@ -14,7 +14,8 @@ obj-$(CONFIG_CPU_S3C2412) += irq.o obj-$(CONFIG_CPU_S3C2412) += clock.o obj-$(CONFIG_CPU_S3C2412) += gpio.o obj-$(CONFIG_S3C2412_DMA) += dma.o -obj-$(CONFIG_S3C2412_PM) += pm.o sleep.o +obj-$(CONFIG_S3C2412_PM) += pm.o +obj-$(CONFIG_S3C2412_PM_SLEEP) += sleep.o obj-$(CONFIG_S3C2412_CPUFREQ) += cpu-freq.o # Machine support diff --git a/arch/arm/mach-s3c2416/Kconfig b/arch/arm/mach-s3c2416/Kconfig index 27b3e7c9d61..df8d14974c9 100644 --- a/arch/arm/mach-s3c2416/Kconfig +++ b/arch/arm/mach-s3c2416/Kconfig @@ -27,6 +27,7 @@ config S3C2416_DMA config S3C2416_PM bool + select S3C2412_PM_SLEEP help Internal config node to apply S3C2416 power management diff --git a/arch/arm/mach-s5pv210/mach-aquila.c b/arch/arm/mach-s5pv210/mach-aquila.c index 28677caf361..461aa035afc 100644 --- a/arch/arm/mach-s5pv210/mach-aquila.c +++ b/arch/arm/mach-s5pv210/mach-aquila.c @@ -378,6 +378,12 @@ static struct max8998_regulator_data aquila_regulators[] = { static struct max8998_platform_data aquila_max8998_pdata = { .num_regulators = ARRAY_SIZE(aquila_regulators), .regulators = aquila_regulators, + .buck1_set1 = S5PV210_GPH0(3), + .buck1_set2 = S5PV210_GPH0(4), + .buck2_set3 = S5PV210_GPH0(5), + .buck1_max_voltage1 = 1200000, + .buck1_max_voltage2 = 1200000, + .buck2_max_voltage = 1200000, }; #endif diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c index b1dcf964a76..e22d5112fd4 100644 --- a/arch/arm/mach-s5pv210/mach-goni.c +++ b/arch/arm/mach-s5pv210/mach-goni.c @@ -518,6 +518,12 @@ static struct max8998_regulator_data goni_regulators[] = { static struct max8998_platform_data goni_max8998_pdata = { .num_regulators = ARRAY_SIZE(goni_regulators), .regulators = goni_regulators, + .buck1_set1 = S5PV210_GPH0(3), + .buck1_set2 = S5PV210_GPH0(4), + .buck2_set3 = S5PV210_GPH0(5), + .buck1_max_voltage1 = 1200000, + .buck1_max_voltage2 = 1200000, + .buck2_max_voltage = 1200000, }; #endif diff --git a/arch/arm/mach-shmobile/include/mach/entry-macro.S b/arch/arm/mach-shmobile/include/mach/entry-macro.S index a285d13c741..f428c4db2b6 100644 --- a/arch/arm/mach-shmobile/include/mach/entry-macro.S +++ b/arch/arm/mach-shmobile/include/mach/entry-macro.S @@ -1,4 +1,5 @@ /* + * Copyright (C) 2010 Magnus Damm * Copyright (C) 2008 Renesas Solutions Corp. * * This program is free software; you can redistribute it and/or modify @@ -14,24 +15,45 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ -#include <mach/hardware.h> #include <mach/irqs.h> +#define INTCA_BASE 0xe6980000 +#define INTFLGA_OFFS 0x00000018 /* accept pending interrupt */ +#define INTEVTA_OFFS 0x00000020 /* vector number of accepted interrupt */ +#define INTLVLA_OFFS 0x00000030 /* priority level of accepted interrupt */ +#define INTLVLB_OFFS 0x00000034 /* previous priority level */ + .macro disable_fiq .endm .macro get_irqnr_preamble, base, tmp - ldr \base, =INTFLGA + ldr \base, =INTCA_BASE .endm .macro arch_ret_to_user, tmp1, tmp2 .endm .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \irqnr, [\base] + /* The single INTFLGA read access below results in the following: + * + * 1. INTLVLB is updated with old priority value from INTLVLA + * 2. Highest priority interrupt is accepted + * 3. INTLVLA is updated to contain priority of accepted interrupt + * 4. Accepted interrupt vector is stored in INTFLGA and INTEVTA + */ + ldr \irqnr, [\base, #INTFLGA_OFFS] + + /* Restore INTLVLA with the value saved in INTLVLB. + * This is required to support interrupt priorities properly. + */ + ldrb \tmp, [\base, #INTLVLB_OFFS] + strb \tmp, [\base, #INTLVLA_OFFS] + + /* Handle invalid vector number case */ cmp \irqnr, #0 beq 1000f - /* intevt to irq number */ + + /* Convert vector to irq number, same as the evt2irq() macro */ lsr \irqnr, \irqnr, #0x5 subs \irqnr, \irqnr, #16 diff --git a/arch/arm/mach-shmobile/include/mach/vmalloc.h b/arch/arm/mach-shmobile/include/mach/vmalloc.h index 4aecf6e3a85..2b8fd8b942f 100644 --- a/arch/arm/mach-shmobile/include/mach/vmalloc.h +++ b/arch/arm/mach-shmobile/include/mach/vmalloc.h @@ -2,6 +2,6 @@ #define __ASM_MACH_VMALLOC_H /* Vmalloc at ... - 0xe5ffffff */ -#define VMALLOC_END 0xe6000000 +#define VMALLOC_END 0xe6000000UL #endif /* __ASM_MACH_VMALLOC_H */ diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index a863f5546a6..c4b2b478b1a 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -15,6 +15,10 @@ * * Support functions for the OMAP internal DMA channels. * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * Converted DMA library into DMA platform driver. + * - G, Manjunath Kondaiah <manjugk@ti.com> + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. @@ -53,7 +57,11 @@ enum { DMA_CHAIN_STARTED, DMA_CHAIN_NOTSTARTED }; #define OMAP_FUNC_MUX_ARM_BASE (0xfffe1000 + 0xec) +static struct omap_system_dma_plat_info *p; +static struct omap_dma_dev_attr *d; + static int enable_1510_mode; +static u32 errata; static struct omap_dma_global_context_registers { u32 dma_irqenable_l0; @@ -61,27 +69,6 @@ static struct omap_dma_global_context_registers { u32 dma_gcr; } omap_dma_global_context; -struct omap_dma_lch { - int next_lch; - int dev_id; - u16 saved_csr; - u16 enabled_irqs; - const char *dev_name; - void (*callback)(int lch, u16 ch_status, void *data); - void *data; - -#ifndef CONFIG_ARCH_OMAP1 - /* required for Dynamic chaining */ - int prev_linked_ch; - int next_linked_ch; - int state; - int chain_id; - - int status; -#endif - long flags; -}; - struct dma_link_info { int *linked_dmach_q; int no_of_lchs_linked; @@ -137,15 +124,6 @@ static int omap_dma_reserve_channels; static spinlock_t dma_chan_lock; static struct omap_dma_lch *dma_chan; -static void __iomem *omap_dma_base; - -static const u8 omap1_dma_irq[OMAP1_LOGICAL_DMA_CH_COUNT] = { - INT_DMA_CH0_6, INT_DMA_CH1_7, INT_DMA_CH2_8, INT_DMA_CH3, - INT_DMA_CH4, INT_DMA_CH5, INT_1610_DMA_CH6, INT_1610_DMA_CH7, - INT_1610_DMA_CH8, INT_1610_DMA_CH9, INT_1610_DMA_CH10, - INT_1610_DMA_CH11, INT_1610_DMA_CH12, INT_1610_DMA_CH13, - INT_1610_DMA_CH14, INT_1610_DMA_CH15, INT_DMA_LCD -}; static inline void disable_lnk(int lch); static void omap_disable_channel_irq(int lch); @@ -154,27 +132,9 @@ static inline void omap_enable_channel_irq(int lch); #define REVISIT_24XX() printk(KERN_ERR "FIXME: no %s on 24xx\n", \ __func__); -#define dma_read(reg) \ -({ \ - u32 __val; \ - if (cpu_class_is_omap1()) \ - __val = __raw_readw(omap_dma_base + OMAP1_DMA_##reg); \ - else \ - __val = __raw_readl(omap_dma_base + OMAP_DMA4_##reg); \ - __val; \ -}) - -#define dma_write(val, reg) \ -({ \ - if (cpu_class_is_omap1()) \ - __raw_writew((u16)(val), omap_dma_base + OMAP1_DMA_##reg); \ - else \ - __raw_writel((val), omap_dma_base + OMAP_DMA4_##reg); \ -}) - #ifdef CONFIG_ARCH_OMAP15XX /* Returns 1 if the DMA module is in OMAP1510-compatible mode, 0 otherwise */ -static int omap_dma_in_1510_mode(void) +int omap_dma_in_1510_mode(void) { return enable_1510_mode; } @@ -206,16 +166,6 @@ static inline void set_gdma_dev(int req, int dev) #define set_gdma_dev(req, dev) do {} while (0) #endif -/* Omap1 only */ -static void clear_lch_regs(int lch) -{ - int i; - void __iomem *lch_base = omap_dma_base + OMAP1_DMA_CH_BASE(lch); - - for (i = 0; i < 0x2c; i += 2) - __raw_writew(0, lch_base + i); -} - void omap_set_dma_priority(int lch, int dst_port, int priority) { unsigned long reg; @@ -248,12 +198,12 @@ void omap_set_dma_priority(int lch, int dst_port, int priority) if (cpu_class_is_omap2()) { u32 ccr; - ccr = dma_read(CCR(lch)); + ccr = p->dma_read(CCR, lch); if (priority) ccr |= (1 << 6); else ccr &= ~(1 << 6); - dma_write(ccr, CCR(lch)); + p->dma_write(ccr, CCR, lch); } } EXPORT_SYMBOL(omap_set_dma_priority); @@ -264,31 +214,31 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, { u32 l; - l = dma_read(CSDP(lch)); + l = p->dma_read(CSDP, lch); l &= ~0x03; l |= data_type; - dma_write(l, CSDP(lch)); + p->dma_write(l, CSDP, lch); if (cpu_class_is_omap1()) { u16 ccr; - ccr = dma_read(CCR(lch)); + ccr = p->dma_read(CCR, lch); ccr &= ~(1 << 5); if (sync_mode == OMAP_DMA_SYNC_FRAME) ccr |= 1 << 5; - dma_write(ccr, CCR(lch)); + p->dma_write(ccr, CCR, lch); - ccr = dma_read(CCR2(lch)); + ccr = p->dma_read(CCR2, lch); ccr &= ~(1 << 2); if (sync_mode == OMAP_DMA_SYNC_BLOCK) ccr |= 1 << 2; - dma_write(ccr, CCR2(lch)); + p->dma_write(ccr, CCR2, lch); } if (cpu_class_is_omap2() && dma_trigger) { u32 val; - val = dma_read(CCR(lch)); + val = p->dma_read(CCR, lch); /* DMA_SYNCHRO_CONTROL_UPPER depends on the channel number */ val &= ~((1 << 23) | (3 << 19) | 0x1f); @@ -313,11 +263,11 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, } else { val &= ~(1 << 24); /* dest synch */ } - dma_write(val, CCR(lch)); + p->dma_write(val, CCR, lch); } - dma_write(elem_count, CEN(lch)); - dma_write(frame_count, CFN(lch)); + p->dma_write(elem_count, CEN, lch); + p->dma_write(frame_count, CFN, lch); } EXPORT_SYMBOL(omap_set_dma_transfer_params); @@ -328,7 +278,7 @@ void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color) if (cpu_class_is_omap1()) { u16 w; - w = dma_read(CCR2(lch)); + w = p->dma_read(CCR2, lch); w &= ~0x03; switch (mode) { @@ -343,23 +293,22 @@ void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color) default: BUG(); } - dma_write(w, CCR2(lch)); + p->dma_write(w, CCR2, lch); - w = dma_read(LCH_CTRL(lch)); + w = p->dma_read(LCH_CTRL, lch); w &= ~0x0f; /* Default is channel type 2D */ if (mode) { - dma_write((u16)color, COLOR_L(lch)); - dma_write((u16)(color >> 16), COLOR_U(lch)); + p->dma_write(color, COLOR, lch); w |= 1; /* Channel type G */ } - dma_write(w, LCH_CTRL(lch)); + p->dma_write(w, LCH_CTRL, lch); } if (cpu_class_is_omap2()) { u32 val; - val = dma_read(CCR(lch)); + val = p->dma_read(CCR, lch); val &= ~((1 << 17) | (1 << 16)); switch (mode) { @@ -374,10 +323,10 @@ void omap_set_dma_color_mode(int lch, enum omap_dma_color_mode mode, u32 color) default: BUG(); } - dma_write(val, CCR(lch)); + p->dma_write(val, CCR, lch); color &= 0xffffff; - dma_write(color, COLOR(lch)); + p->dma_write(color, COLOR, lch); } } EXPORT_SYMBOL(omap_set_dma_color_mode); @@ -387,10 +336,10 @@ void omap_set_dma_write_mode(int lch, enum omap_dma_write_mode mode) if (cpu_class_is_omap2()) { u32 csdp; - csdp = dma_read(CSDP(lch)); + csdp = p->dma_read(CSDP, lch); csdp &= ~(0x3 << 16); csdp |= (mode << 16); - dma_write(csdp, CSDP(lch)); + p->dma_write(csdp, CSDP, lch); } } EXPORT_SYMBOL(omap_set_dma_write_mode); @@ -400,10 +349,10 @@ void omap_set_dma_channel_mode(int lch, enum omap_dma_channel_mode mode) if (cpu_class_is_omap1() && !cpu_is_omap15xx()) { u32 l; - l = dma_read(LCH_CTRL(lch)); + l = p->dma_read(LCH_CTRL, lch); l &= ~0x7; l |= mode; - dma_write(l, LCH_CTRL(lch)); + p->dma_write(l, LCH_CTRL, lch); } } EXPORT_SYMBOL(omap_set_dma_channel_mode); @@ -418,27 +367,21 @@ void omap_set_dma_src_params(int lch, int src_port, int src_amode, if (cpu_class_is_omap1()) { u16 w; - w = dma_read(CSDP(lch)); + w = p->dma_read(CSDP, lch); w &= ~(0x1f << 2); w |= src_port << 2; - dma_write(w, CSDP(lch)); + p->dma_write(w, CSDP, lch); } - l = dma_read(CCR(lch)); + l = p->dma_read(CCR, lch); l &= ~(0x03 << 12); l |= src_amode << 12; - dma_write(l, CCR(lch)); - - if (cpu_class_is_omap1()) { - dma_write(src_start >> 16, CSSA_U(lch)); - dma_write((u16)src_start, CSSA_L(lch)); - } + p->dma_write(l, CCR, lch); - if (cpu_class_is_omap2()) - dma_write(src_start, CSSA(lch)); + p->dma_write(src_start, CSSA, lch); - dma_write(src_ei, CSEI(lch)); - dma_write(src_fi, CSFI(lch)); + p->dma_write(src_ei, CSEI, lch); + p->dma_write(src_fi, CSFI, lch); } EXPORT_SYMBOL(omap_set_dma_src_params); @@ -466,8 +409,8 @@ void omap_set_dma_src_index(int lch, int eidx, int fidx) if (cpu_class_is_omap2()) return; - dma_write(eidx, CSEI(lch)); - dma_write(fidx, CSFI(lch)); + p->dma_write(eidx, CSEI, lch); + p->dma_write(fidx, CSFI, lch); } EXPORT_SYMBOL(omap_set_dma_src_index); @@ -475,11 +418,11 @@ void omap_set_dma_src_data_pack(int lch, int enable) { u32 l; - l = dma_read(CSDP(lch)); + l = p->dma_read(CSDP, lch); l &= ~(1 << 6); if (enable) l |= (1 << 6); - dma_write(l, CSDP(lch)); + p->dma_write(l, CSDP, lch); } EXPORT_SYMBOL(omap_set_dma_src_data_pack); @@ -488,7 +431,7 @@ void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) unsigned int burst = 0; u32 l; - l = dma_read(CSDP(lch)); + l = p->dma_read(CSDP, lch); l &= ~(0x03 << 7); switch (burst_mode) { @@ -524,7 +467,7 @@ void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) } l |= (burst << 7); - dma_write(l, CSDP(lch)); + p->dma_write(l, CSDP, lch); } EXPORT_SYMBOL(omap_set_dma_src_burst_mode); @@ -536,27 +479,21 @@ void omap_set_dma_dest_params(int lch, int dest_port, int dest_amode, u32 l; if (cpu_class_is_omap1()) { - l = dma_read(CSDP(lch)); + l = p->dma_read(CSDP, lch); l &= ~(0x1f << 9); l |= dest_port << 9; - dma_write(l, CSDP(lch)); + p->dma_write(l, CSDP, lch); } - l = dma_read(CCR(lch)); + l = p->dma_read(CCR, lch); l &= ~(0x03 << 14); l |= dest_amode << 14; - dma_write(l, CCR(lch)); - - if (cpu_class_is_omap1()) { - dma_write(dest_start >> 16, CDSA_U(lch)); - dma_write(dest_start, CDSA_L(lch)); - } + p->dma_write(l, CCR, lch); - if (cpu_class_is_omap2()) - dma_write(dest_start, CDSA(lch)); + p->dma_write(dest_start, CDSA, lch); - dma_write(dst_ei, CDEI(lch)); - dma_write(dst_fi, CDFI(lch)); + p->dma_write(dst_ei, CDEI, lch); + p->dma_write(dst_fi, CDFI, lch); } EXPORT_SYMBOL(omap_set_dma_dest_params); @@ -565,8 +502,8 @@ void omap_set_dma_dest_index(int lch, int eidx, int fidx) if (cpu_class_is_omap2()) return; - dma_write(eidx, CDEI(lch)); - dma_write(fidx, CDFI(lch)); + p->dma_write(eidx, CDEI, lch); + p->dma_write(fidx, CDFI, lch); } EXPORT_SYMBOL(omap_set_dma_dest_index); @@ -574,11 +511,11 @@ void omap_set_dma_dest_data_pack(int lch, int enable) { u32 l; - l = dma_read(CSDP(lch)); + l = p->dma_read(CSDP, lch); l &= ~(1 << 13); if (enable) l |= 1 << 13; - dma_write(l, CSDP(lch)); + p->dma_write(l, CSDP, lch); } EXPORT_SYMBOL(omap_set_dma_dest_data_pack); @@ -587,7 +524,7 @@ void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) unsigned int burst = 0; u32 l; - l = dma_read(CSDP(lch)); + l = p->dma_read(CSDP, lch); l &= ~(0x03 << 14); switch (burst_mode) { @@ -620,7 +557,7 @@ void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode) return; } l |= (burst << 14); - dma_write(l, CSDP(lch)); + p->dma_write(l, CSDP, lch); } EXPORT_SYMBOL(omap_set_dma_dest_burst_mode); @@ -630,18 +567,18 @@ static inline void omap_enable_channel_irq(int lch) /* Clear CSR */ if (cpu_class_is_omap1()) - status = dma_read(CSR(lch)); + status = p->dma_read(CSR, lch); else if (cpu_class_is_omap2()) - dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(lch)); + p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, lch); /* Enable some nice interrupts. */ - dma_write(dma_chan[lch].enabled_irqs, CICR(lch)); + p->dma_write(dma_chan[lch].enabled_irqs, CICR, lch); } static void omap_disable_channel_irq(int lch) { if (cpu_class_is_omap2()) - dma_write(0, CICR(lch)); + p->dma_write(0, CICR, lch); } void omap_enable_dma_irq(int lch, u16 bits) @@ -660,7 +597,7 @@ static inline void enable_lnk(int lch) { u32 l; - l = dma_read(CLNK_CTRL(lch)); + l = p->dma_read(CLNK_CTRL, lch); if (cpu_class_is_omap1()) l &= ~(1 << 14); @@ -675,18 +612,18 @@ static inline void enable_lnk(int lch) l = dma_chan[lch].next_linked_ch | (1 << 15); #endif - dma_write(l, CLNK_CTRL(lch)); + p->dma_write(l, CLNK_CTRL, lch); } static inline void disable_lnk(int lch) { u32 l; - l = dma_read(CLNK_CTRL(lch)); + l = p->dma_read(CLNK_CTRL, lch); /* Disable interrupts */ if (cpu_class_is_omap1()) { - dma_write(0, CICR(lch)); + p->dma_write(0, CICR, lch); /* Set the STOP_LNK bit */ l |= 1 << 14; } @@ -697,7 +634,7 @@ static inline void disable_lnk(int lch) l &= ~(1 << 15); } - dma_write(l, CLNK_CTRL(lch)); + p->dma_write(l, CLNK_CTRL, lch); dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE; } @@ -710,9 +647,9 @@ static inline void omap2_enable_irq_lch(int lch) return; spin_lock_irqsave(&dma_chan_lock, flags); - val = dma_read(IRQENABLE_L0); + val = p->dma_read(IRQENABLE_L0, lch); val |= 1 << lch; - dma_write(val, IRQENABLE_L0); + p->dma_write(val, IRQENABLE_L0, lch); spin_unlock_irqrestore(&dma_chan_lock, flags); } @@ -725,9 +662,9 @@ static inline void omap2_disable_irq_lch(int lch) return; spin_lock_irqsave(&dma_chan_lock, flags); - val = dma_read(IRQENABLE_L0); + val = p->dma_read(IRQENABLE_L0, lch); val &= ~(1 << lch); - dma_write(val, IRQENABLE_L0); + p->dma_write(val, IRQENABLE_L0, lch); spin_unlock_irqrestore(&dma_chan_lock, flags); } @@ -754,8 +691,8 @@ int omap_request_dma(int dev_id, const char *dev_name, chan = dma_chan + free_ch; chan->dev_id = dev_id; - if (cpu_class_is_omap1()) - clear_lch_regs(free_ch); + if (p->clear_lch_regs) + p->clear_lch_regs(free_ch); if (cpu_class_is_omap2()) omap_clear_dma(free_ch); @@ -792,17 +729,17 @@ int omap_request_dma(int dev_id, const char *dev_name, * Disable the 1510 compatibility mode and set the sync device * id. */ - dma_write(dev_id | (1 << 10), CCR(free_ch)); + p->dma_write(dev_id | (1 << 10), CCR, free_ch); } else if (cpu_is_omap7xx() || cpu_is_omap15xx()) { - dma_write(dev_id, CCR(free_ch)); + p->dma_write(dev_id, CCR, free_ch); } if (cpu_class_is_omap2()) { omap2_enable_irq_lch(free_ch); omap_enable_channel_irq(free_ch); /* Clear the CSR register and IRQ status register */ - dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(free_ch)); - dma_write(1 << free_ch, IRQSTATUS_L0); + p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, free_ch); + p->dma_write(1 << free_ch, IRQSTATUS_L0, 0); } *dma_ch_out = free_ch; @@ -823,23 +760,23 @@ void omap_free_dma(int lch) if (cpu_class_is_omap1()) { /* Disable all DMA interrupts for the channel. */ - dma_write(0, CICR(lch)); + p->dma_write(0, CICR, lch); /* Make sure the DMA transfer is stopped. */ - dma_write(0, CCR(lch)); + p->dma_write(0, CCR, lch); } if (cpu_class_is_omap2()) { omap2_disable_irq_lch(lch); /* Clear the CSR register and IRQ status register */ - dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(lch)); - dma_write(1 << lch, IRQSTATUS_L0); + p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, lch); + p->dma_write(1 << lch, IRQSTATUS_L0, lch); /* Disable all DMA interrupts for the channel. */ - dma_write(0, CICR(lch)); + p->dma_write(0, CICR, lch); /* Make sure the DMA transfer is stopped. */ - dma_write(0, CCR(lch)); + p->dma_write(0, CCR, lch); omap_clear_dma(lch); } @@ -880,7 +817,7 @@ omap_dma_set_global_params(int arb_rate, int max_fifo_depth, int tparams) reg |= (0x3 & tparams) << 12; reg |= (arb_rate & 0xff) << 16; - dma_write(reg, GCR); + p->dma_write(reg, GCR, 0); } EXPORT_SYMBOL(omap_dma_set_global_params); @@ -903,14 +840,14 @@ omap_dma_set_prio_lch(int lch, unsigned char read_prio, printk(KERN_ERR "Invalid channel id\n"); return -EINVAL; } - l = dma_read(CCR(lch)); + l = p->dma_read(CCR, lch); l &= ~((1 << 6) | (1 << 26)); if (cpu_is_omap2430() || cpu_is_omap34xx() || cpu_is_omap44xx()) l |= ((read_prio & 0x1) << 6) | ((write_prio & 0x1) << 26); else l |= ((read_prio & 0x1) << 6); - dma_write(l, CCR(lch)); + p->dma_write(l, CCR, lch); return 0; } @@ -925,25 +862,7 @@ void omap_clear_dma(int lch) unsigned long flags; local_irq_save(flags); - - if (cpu_class_is_omap1()) { - u32 l; - - l = dma_read(CCR(lch)); - l &= ~OMAP_DMA_CCR_EN; - dma_write(l, CCR(lch)); - - /* Clear pending interrupts */ - l = dma_read(CSR(lch)); - } - - if (cpu_class_is_omap2()) { - int i; - void __iomem *lch_base = omap_dma_base + OMAP_DMA4_CH_BASE(lch); - for (i = 0; i < 0x44; i += 4) - __raw_writel(0, lch_base + i); - } - + p->clear_dma(lch); local_irq_restore(flags); } EXPORT_SYMBOL(omap_clear_dma); @@ -957,13 +876,13 @@ void omap_start_dma(int lch) * before starting dma transfer. */ if (cpu_is_omap15xx()) - dma_write(0, CPC(lch)); + p->dma_write(0, CPC, lch); else - dma_write(0, CDAC(lch)); + p->dma_write(0, CDAC, lch); if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) { int next_lch, cur_lch; - char dma_chan_link_map[OMAP_DMA4_LOGICAL_DMA_CH_COUNT]; + char dma_chan_link_map[dma_lch_count]; dma_chan_link_map[lch] = 1; /* Set the link register of the first channel */ @@ -985,32 +904,18 @@ void omap_start_dma(int lch) cur_lch = next_lch; } while (next_lch != -1); - } else if (cpu_is_omap242x() || - (cpu_is_omap243x() && omap_type() <= OMAP2430_REV_ES1_0)) { - - /* Errata: Need to write lch even if not using chaining */ - dma_write(lch, CLNK_CTRL(lch)); - } + } else if (IS_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS)) + p->dma_write(lch, CLNK_CTRL, lch); omap_enable_channel_irq(lch); - l = dma_read(CCR(lch)); - - /* - * Errata: Inter Frame DMA buffering issue (All OMAP2420 and - * OMAP2430ES1.0): DMA will wrongly buffer elements if packing and - * bursting is enabled. This might result in data gets stalled in - * FIFO at the end of the block. - * Workaround: DMA channels must have BUFFERING_DISABLED bit set to - * guarantee no data will stay in the DMA FIFO in case inter frame - * buffering occurs. - */ - if (cpu_is_omap2420() || - (cpu_is_omap2430() && (omap_type() == OMAP2430_REV_ES1_0))) - l |= OMAP_DMA_CCR_BUFFERING_DISABLE; + l = p->dma_read(CCR, lch); + if (IS_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING)) + l |= OMAP_DMA_CCR_BUFFERING_DISABLE; l |= OMAP_DMA_CCR_EN; - dma_write(l, CCR(lch)); + + p->dma_write(l, CCR, lch); dma_chan[lch].flags |= OMAP_DMA_ACTIVE; } @@ -1022,46 +927,46 @@ void omap_stop_dma(int lch) /* Disable all interrupts on the channel */ if (cpu_class_is_omap1()) - dma_write(0, CICR(lch)); + p->dma_write(0, CICR, lch); - l = dma_read(CCR(lch)); - /* OMAP3 Errata i541: sDMA FIFO draining does not finish */ - if (cpu_is_omap34xx() && (l & OMAP_DMA_CCR_SEL_SRC_DST_SYNC)) { + l = p->dma_read(CCR, lch); + if (IS_DMA_ERRATA(DMA_ERRATA_i541) && + (l & OMAP_DMA_CCR_SEL_SRC_DST_SYNC)) { int i = 0; u32 sys_cf; /* Configure No-Standby */ - l = dma_read(OCP_SYSCONFIG); + l = p->dma_read(OCP_SYSCONFIG, lch); sys_cf = l; l &= ~DMA_SYSCONFIG_MIDLEMODE_MASK; l |= DMA_SYSCONFIG_MIDLEMODE(DMA_IDLEMODE_NO_IDLE); - dma_write(l , OCP_SYSCONFIG); + p->dma_write(l , OCP_SYSCONFIG, 0); - l = dma_read(CCR(lch)); + l = p->dma_read(CCR, lch); l &= ~OMAP_DMA_CCR_EN; - dma_write(l, CCR(lch)); + p->dma_write(l, CCR, lch); /* Wait for sDMA FIFO drain */ - l = dma_read(CCR(lch)); + l = p->dma_read(CCR, lch); while (i < 100 && (l & (OMAP_DMA_CCR_RD_ACTIVE | OMAP_DMA_CCR_WR_ACTIVE))) { udelay(5); i++; - l = dma_read(CCR(lch)); + l = p->dma_read(CCR, lch); } if (i >= 100) printk(KERN_ERR "DMA drain did not complete on " "lch %d\n", lch); /* Restore OCP_SYSCONFIG */ - dma_write(sys_cf, OCP_SYSCONFIG); + p->dma_write(sys_cf, OCP_SYSCONFIG, lch); } else { l &= ~OMAP_DMA_CCR_EN; - dma_write(l, CCR(lch)); + p->dma_write(l, CCR, lch); } if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) { int next_lch, cur_lch = lch; - char dma_chan_link_map[OMAP_DMA4_LOGICAL_DMA_CH_COUNT]; + char dma_chan_link_map[dma_lch_count]; memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map)); do { @@ -1122,19 +1027,15 @@ dma_addr_t omap_get_dma_src_pos(int lch) dma_addr_t offset = 0; if (cpu_is_omap15xx()) - offset = dma_read(CPC(lch)); + offset = p->dma_read(CPC, lch); else - offset = dma_read(CSAC(lch)); + offset = p->dma_read(CSAC, lch); - /* - * omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is - * read before the DMA controller finished disabling the channel. - */ - if (!cpu_is_omap15xx() && offset == 0) - offset = dma_read(CSAC(lch)); + if (IS_DMA_ERRATA(DMA_ERRATA_3_3) && offset == 0) + offset = p->dma_read(CSAC, lch); if (cpu_class_is_omap1()) - offset |= (dma_read(CSSA_U(lch)) << 16); + offset |= (p->dma_read(CSSA, lch) & 0xFFFF0000); return offset; } @@ -1153,19 +1054,19 @@ dma_addr_t omap_get_dma_dst_pos(int lch) dma_addr_t offset = 0; if (cpu_is_omap15xx()) - offset = dma_read(CPC(lch)); + offset = p->dma_read(CPC, lch); else - offset = dma_read(CDAC(lch)); + offset = p->dma_read(CDAC, lch); /* * omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is * read before the DMA controller finished disabling the channel. */ if (!cpu_is_omap15xx() && offset == 0) - offset = dma_read(CDAC(lch)); + offset = p->dma_read(CDAC, lch); if (cpu_class_is_omap1()) - offset |= (dma_read(CDSA_U(lch)) << 16); + offset |= (p->dma_read(CDSA, lch) & 0xFFFF0000); return offset; } @@ -1173,7 +1074,7 @@ EXPORT_SYMBOL(omap_get_dma_dst_pos); int omap_get_dma_active_status(int lch) { - return (dma_read(CCR(lch)) & OMAP_DMA_CCR_EN) != 0; + return (p->dma_read(CCR, lch) & OMAP_DMA_CCR_EN) != 0; } EXPORT_SYMBOL(omap_get_dma_active_status); @@ -1186,7 +1087,7 @@ int omap_dma_running(void) return 1; for (lch = 0; lch < dma_chan_count; lch++) - if (dma_read(CCR(lch)) & OMAP_DMA_CCR_EN) + if (p->dma_read(CCR, lch) & OMAP_DMA_CCR_EN) return 1; return 0; @@ -1201,8 +1102,8 @@ void omap_dma_link_lch(int lch_head, int lch_queue) { if (omap_dma_in_1510_mode()) { if (lch_head == lch_queue) { - dma_write(dma_read(CCR(lch_head)) | (3 << 8), - CCR(lch_head)); + p->dma_write(p->dma_read(CCR, lch_head) | (3 << 8), + CCR, lch_head); return; } printk(KERN_ERR "DMA linking is not supported in 1510 mode\n"); @@ -1228,8 +1129,8 @@ void omap_dma_unlink_lch(int lch_head, int lch_queue) { if (omap_dma_in_1510_mode()) { if (lch_head == lch_queue) { - dma_write(dma_read(CCR(lch_head)) & ~(3 << 8), - CCR(lch_head)); + p->dma_write(p->dma_read(CCR, lch_head) & ~(3 << 8), + CCR, lch_head); return; } printk(KERN_ERR "DMA linking is not supported in 1510 mode\n"); @@ -1255,8 +1156,6 @@ void omap_dma_unlink_lch(int lch_head, int lch_queue) } EXPORT_SYMBOL(omap_dma_unlink_lch); -/*----------------------------------------------------------------------------*/ - #ifndef CONFIG_ARCH_OMAP1 /* Create chain of DMA channesls */ static void create_dma_lch_chain(int lch_head, int lch_queue) @@ -1281,15 +1180,15 @@ static void create_dma_lch_chain(int lch_head, int lch_queue) lch_queue; } - l = dma_read(CLNK_CTRL(lch_head)); + l = p->dma_read(CLNK_CTRL, lch_head); l &= ~(0x1f); l |= lch_queue; - dma_write(l, CLNK_CTRL(lch_head)); + p->dma_write(l, CLNK_CTRL, lch_head); - l = dma_read(CLNK_CTRL(lch_queue)); + l = p->dma_read(CLNK_CTRL, lch_queue); l &= ~(0x1f); l |= (dma_chan[lch_queue].next_linked_ch); - dma_write(l, CLNK_CTRL(lch_queue)); + p->dma_write(l, CLNK_CTRL, lch_queue); } /** @@ -1565,13 +1464,13 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, /* Set the params to the free channel */ if (src_start != 0) - dma_write(src_start, CSSA(lch)); + p->dma_write(src_start, CSSA, lch); if (dest_start != 0) - dma_write(dest_start, CDSA(lch)); + p->dma_write(dest_start, CDSA, lch); /* Write the buffer size */ - dma_write(elem_count, CEN(lch)); - dma_write(frame_count, CFN(lch)); + p->dma_write(elem_count, CEN, lch); + p->dma_write(frame_count, CFN, lch); /* * If the chain is dynamically linked, @@ -1604,8 +1503,8 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, enable_lnk(dma_chan[lch].prev_linked_ch); dma_chan[lch].state = DMA_CH_QUEUED; start_dma = 0; - if (0 == ((1 << 7) & dma_read( - CCR(dma_chan[lch].prev_linked_ch)))) { + if (0 == ((1 << 7) & p->dma_read( + CCR, dma_chan[lch].prev_linked_ch))) { disable_lnk(dma_chan[lch]. prev_linked_ch); pr_debug("\n prev ch is stopped\n"); @@ -1621,7 +1520,7 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, } omap_enable_channel_irq(lch); - l = dma_read(CCR(lch)); + l = p->dma_read(CCR, lch); if ((0 == (l & (1 << 24)))) l &= ~(1 << 25); @@ -1632,12 +1531,12 @@ int omap_dma_chain_a_transfer(int chain_id, int src_start, int dest_start, l |= (1 << 7); dma_chan[lch].state = DMA_CH_STARTED; pr_debug("starting %d\n", lch); - dma_write(l, CCR(lch)); + p->dma_write(l, CCR, lch); } else start_dma = 0; } else { if (0 == (l & (1 << 7))) - dma_write(l, CCR(lch)); + p->dma_write(l, CCR, lch); } dma_chan[lch].flags |= OMAP_DMA_ACTIVE; } @@ -1682,7 +1581,7 @@ int omap_start_dma_chain_transfers(int chain_id) omap_enable_channel_irq(channels[0]); } - l = dma_read(CCR(channels[0])); + l = p->dma_read(CCR, channels[0]); l |= (1 << 7); dma_linked_lch[chain_id].chain_state = DMA_CHAIN_STARTED; dma_chan[channels[0]].state = DMA_CH_STARTED; @@ -1691,7 +1590,7 @@ int omap_start_dma_chain_transfers(int chain_id) l &= ~(1 << 25); else l |= (1 << 25); - dma_write(l, CCR(channels[0])); + p->dma_write(l, CCR, channels[0]); dma_chan[channels[0]].flags |= OMAP_DMA_ACTIVE; @@ -1711,7 +1610,7 @@ int omap_stop_dma_chain_transfers(int chain_id) { int *channels; u32 l, i; - u32 sys_cf; + u32 sys_cf = 0; /* Check for input params */ if (unlikely((chain_id < 0 || chain_id >= dma_lch_count))) { @@ -1726,22 +1625,20 @@ int omap_stop_dma_chain_transfers(int chain_id) } channels = dma_linked_lch[chain_id].linked_dmach_q; - /* - * DMA Errata: - * Special programming model needed to disable DMA before end of block - */ - sys_cf = dma_read(OCP_SYSCONFIG); - l = sys_cf; - /* Middle mode reg set no Standby */ - l &= ~((1 << 12)|(1 << 13)); - dma_write(l, OCP_SYSCONFIG); + if (IS_DMA_ERRATA(DMA_ERRATA_i88)) { + sys_cf = p->dma_read(OCP_SYSCONFIG, 0); + l = sys_cf; + /* Middle mode reg set no Standby */ + l &= ~((1 << 12)|(1 << 13)); + p->dma_write(l, OCP_SYSCONFIG, 0); + } for (i = 0; i < dma_linked_lch[chain_id].no_of_lchs_linked; i++) { /* Stop the Channel transmission */ - l = dma_read(CCR(channels[i])); + l = p->dma_read(CCR, channels[i]); l &= ~(1 << 7); - dma_write(l, CCR(channels[i])); + p->dma_write(l, CCR, channels[i]); /* Disable the link in all the channels */ disable_lnk(channels[i]); @@ -1753,8 +1650,8 @@ int omap_stop_dma_chain_transfers(int chain_id) /* Reset the Queue pointers */ OMAP_DMA_CHAIN_QINIT(chain_id); - /* Errata - put in the old value */ - dma_write(sys_cf, OCP_SYSCONFIG); + if (IS_DMA_ERRATA(DMA_ERRATA_i88)) + p->dma_write(sys_cf, OCP_SYSCONFIG, 0); return 0; } @@ -1796,8 +1693,8 @@ int omap_get_dma_chain_index(int chain_id, int *ei, int *fi) /* Get the current channel */ lch = channels[dma_linked_lch[chain_id].q_head]; - *ei = dma_read(CCEN(lch)); - *fi = dma_read(CCFN(lch)); + *ei = p->dma_read(CCEN, lch); + *fi = p->dma_read(CCFN, lch); return 0; } @@ -1834,7 +1731,7 @@ int omap_get_dma_chain_dst_pos(int chain_id) /* Get the current channel */ lch = channels[dma_linked_lch[chain_id].q_head]; - return dma_read(CDAC(lch)); + return p->dma_read(CDAC, lch); } EXPORT_SYMBOL(omap_get_dma_chain_dst_pos); @@ -1868,7 +1765,7 @@ int omap_get_dma_chain_src_pos(int chain_id) /* Get the current channel */ lch = channels[dma_linked_lch[chain_id].q_head]; - return dma_read(CSAC(lch)); + return p->dma_read(CSAC, lch); } EXPORT_SYMBOL(omap_get_dma_chain_src_pos); #endif /* ifndef CONFIG_ARCH_OMAP1 */ @@ -1885,7 +1782,7 @@ static int omap1_dma_handle_ch(int ch) csr = dma_chan[ch].saved_csr; dma_chan[ch].saved_csr = 0; } else - csr = dma_read(CSR(ch)); + csr = p->dma_read(CSR, ch); if (enable_1510_mode && ch <= 2 && (csr >> 7) != 0) { dma_chan[ch + 6].saved_csr = csr >> 7; csr &= 0x7f; @@ -1938,13 +1835,13 @@ static irqreturn_t omap1_dma_irq_handler(int irq, void *dev_id) static int omap2_dma_handle_ch(int ch) { - u32 status = dma_read(CSR(ch)); + u32 status = p->dma_read(CSR, ch); if (!status) { if (printk_ratelimit()) printk(KERN_WARNING "Spurious DMA IRQ for lch %d\n", ch); - dma_write(1 << ch, IRQSTATUS_L0); + p->dma_write(1 << ch, IRQSTATUS_L0, ch); return 0; } if (unlikely(dma_chan[ch].dev_id == -1)) { @@ -1960,17 +1857,12 @@ static int omap2_dma_handle_ch(int ch) if (unlikely(status & OMAP2_DMA_TRANS_ERR_IRQ)) { printk(KERN_INFO "DMA transaction error with device %d\n", dma_chan[ch].dev_id); - if (cpu_class_is_omap2()) { - /* - * Errata: sDMA Channel is not disabled - * after a transaction error. So we explicitely - * disable the channel - */ + if (IS_DMA_ERRATA(DMA_ERRATA_i378)) { u32 ccr; - ccr = dma_read(CCR(ch)); + ccr = p->dma_read(CCR, ch); ccr &= ~OMAP_DMA_CCR_EN; - dma_write(ccr, CCR(ch)); + p->dma_write(ccr, CCR, ch); dma_chan[ch].flags &= ~OMAP_DMA_ACTIVE; } } @@ -1981,16 +1873,16 @@ static int omap2_dma_handle_ch(int ch) printk(KERN_INFO "DMA misaligned error with device %d\n", dma_chan[ch].dev_id); - dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(ch)); - dma_write(1 << ch, IRQSTATUS_L0); + p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, ch); + p->dma_write(1 << ch, IRQSTATUS_L0, ch); /* read back the register to flush the write */ - dma_read(IRQSTATUS_L0); + p->dma_read(IRQSTATUS_L0, ch); /* If the ch is not chained then chain_id will be -1 */ if (dma_chan[ch].chain_id != -1) { int chain_id = dma_chan[ch].chain_id; dma_chan[ch].state = DMA_CH_NOTSTARTED; - if (dma_read(CLNK_CTRL(ch)) & (1 << 15)) + if (p->dma_read(CLNK_CTRL, ch) & (1 << 15)) dma_chan[dma_chan[ch].next_linked_ch].state = DMA_CH_STARTED; if (dma_linked_lch[chain_id].chain_mode == @@ -2000,10 +1892,10 @@ static int omap2_dma_handle_ch(int ch) if (!OMAP_DMA_CHAIN_QEMPTY(chain_id)) OMAP_DMA_CHAIN_INCQHEAD(chain_id); - status = dma_read(CSR(ch)); + status = p->dma_read(CSR, ch); } - dma_write(status, CSR(ch)); + p->dma_write(status, CSR, ch); if (likely(dma_chan[ch].callback != NULL)) dma_chan[ch].callback(ch, status, dma_chan[ch].data); @@ -2017,13 +1909,13 @@ static irqreturn_t omap2_dma_irq_handler(int irq, void *dev_id) u32 val, enable_reg; int i; - val = dma_read(IRQSTATUS_L0); + val = p->dma_read(IRQSTATUS_L0, 0); if (val == 0) { if (printk_ratelimit()) printk(KERN_WARNING "Spurious DMA IRQ\n"); return IRQ_HANDLED; } - enable_reg = dma_read(IRQENABLE_L0); + enable_reg = p->dma_read(IRQENABLE_L0, 0); val &= enable_reg; /* Dispatch only relevant interrupts */ for (i = 0; i < dma_lch_count && val != 0; i++) { if (val & 1) @@ -2049,119 +1941,66 @@ static struct irqaction omap24xx_dma_irq; void omap_dma_global_context_save(void) { omap_dma_global_context.dma_irqenable_l0 = - dma_read(IRQENABLE_L0); + p->dma_read(IRQENABLE_L0, 0); omap_dma_global_context.dma_ocp_sysconfig = - dma_read(OCP_SYSCONFIG); - omap_dma_global_context.dma_gcr = dma_read(GCR); + p->dma_read(OCP_SYSCONFIG, 0); + omap_dma_global_context.dma_gcr = p->dma_read(GCR, 0); } void omap_dma_global_context_restore(void) { int ch; - dma_write(omap_dma_global_context.dma_gcr, GCR); - dma_write(omap_dma_global_context.dma_ocp_sysconfig, - OCP_SYSCONFIG); - dma_write(omap_dma_global_context.dma_irqenable_l0, - IRQENABLE_L0); + p->dma_write(omap_dma_global_context.dma_gcr, GCR, 0); + p->dma_write(omap_dma_global_context.dma_ocp_sysconfig, + OCP_SYSCONFIG, 0); + p->dma_write(omap_dma_global_context.dma_irqenable_l0, + IRQENABLE_L0, 0); - /* - * A bug in ROM code leaves IRQ status for channels 0 and 1 uncleared - * after secure sram context save and restore. Hence we need to - * manually clear those IRQs to avoid spurious interrupts. This - * affects only secure devices. - */ - if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP)) - dma_write(0x3 , IRQSTATUS_L0); + if (IS_DMA_ERRATA(DMA_ROMCODE_BUG)) + p->dma_write(0x3 , IRQSTATUS_L0, 0); for (ch = 0; ch < dma_chan_count; ch++) if (dma_chan[ch].dev_id != -1) omap_clear_dma(ch); } -/*----------------------------------------------------------------------------*/ - -static int __init omap_init_dma(void) +static int __devinit omap_system_dma_probe(struct platform_device *pdev) { - unsigned long base; - int ch, r; - - if (cpu_class_is_omap1()) { - base = OMAP1_DMA_BASE; - dma_lch_count = OMAP1_LOGICAL_DMA_CH_COUNT; - } else if (cpu_is_omap24xx()) { - base = OMAP24XX_DMA4_BASE; - dma_lch_count = OMAP_DMA4_LOGICAL_DMA_CH_COUNT; - } else if (cpu_is_omap34xx()) { - base = OMAP34XX_DMA4_BASE; - dma_lch_count = OMAP_DMA4_LOGICAL_DMA_CH_COUNT; - } else if (cpu_is_omap44xx()) { - base = OMAP44XX_DMA4_BASE; - dma_lch_count = OMAP_DMA4_LOGICAL_DMA_CH_COUNT; - } else { - pr_err("DMA init failed for unsupported omap\n"); - return -ENODEV; + int ch, ret = 0; + int dma_irq; + char irq_name[4]; + int irq_rel; + + p = pdev->dev.platform_data; + if (!p) { + dev_err(&pdev->dev, "%s: System DMA initialized without" + "platform data\n", __func__); + return -EINVAL; } - omap_dma_base = ioremap(base, SZ_4K); - BUG_ON(!omap_dma_base); + d = p->dma_attr; + errata = p->errata; - if (cpu_class_is_omap2() && omap_dma_reserve_channels + if ((d->dev_caps & RESERVE_CHANNEL) && omap_dma_reserve_channels && (omap_dma_reserve_channels <= dma_lch_count)) - dma_lch_count = omap_dma_reserve_channels; + d->lch_count = omap_dma_reserve_channels; - dma_chan = kzalloc(sizeof(struct omap_dma_lch) * dma_lch_count, - GFP_KERNEL); - if (!dma_chan) { - r = -ENOMEM; - goto out_unmap; - } + dma_lch_count = d->lch_count; + dma_chan_count = dma_lch_count; + dma_chan = d->chan; + enable_1510_mode = d->dev_caps & ENABLE_1510_MODE; if (cpu_class_is_omap2()) { dma_linked_lch = kzalloc(sizeof(struct dma_link_info) * dma_lch_count, GFP_KERNEL); if (!dma_linked_lch) { - r = -ENOMEM; - goto out_free; + ret = -ENOMEM; + goto exit_dma_lch_fail; } } - if (cpu_is_omap15xx()) { - printk(KERN_INFO "DMA support for OMAP15xx initialized\n"); - dma_chan_count = 9; - enable_1510_mode = 1; - } else if (cpu_is_omap16xx() || cpu_is_omap7xx()) { - printk(KERN_INFO "OMAP DMA hardware version %d\n", - dma_read(HW_ID)); - printk(KERN_INFO "DMA capabilities: %08x:%08x:%04x:%04x:%04x\n", - (dma_read(CAPS_0_U) << 16) | - dma_read(CAPS_0_L), - (dma_read(CAPS_1_U) << 16) | - dma_read(CAPS_1_L), - dma_read(CAPS_2), dma_read(CAPS_3), - dma_read(CAPS_4)); - if (!enable_1510_mode) { - u16 w; - - /* Disable OMAP 3.0/3.1 compatibility mode. */ - w = dma_read(GSCR); - w |= 1 << 3; - dma_write(w, GSCR); - dma_chan_count = 16; - } else - dma_chan_count = 9; - } else if (cpu_class_is_omap2()) { - u8 revision = dma_read(REVISION) & 0xff; - printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n", - revision >> 4, revision & 0xf); - dma_chan_count = dma_lch_count; - } else { - dma_chan_count = 0; - return 0; - } - spin_lock_init(&dma_chan_lock); - for (ch = 0; ch < dma_chan_count; ch++) { omap_clear_dma(ch); if (cpu_class_is_omap2()) @@ -2178,20 +2017,23 @@ static int __init omap_init_dma(void) * request_irq() doesn't like dev_id (ie. ch) being * zero, so we have to kludge around this. */ - r = request_irq(omap1_dma_irq[ch], + sprintf(&irq_name[0], "%d", ch); + dma_irq = platform_get_irq_byname(pdev, irq_name); + + if (dma_irq < 0) { + ret = dma_irq; + goto exit_dma_irq_fail; + } + + /* INT_DMA_LCD is handled in lcd_dma.c */ + if (dma_irq == INT_DMA_LCD) + continue; + + ret = request_irq(dma_irq, omap1_dma_irq_handler, 0, "DMA", (void *) (ch + 1)); - if (r != 0) { - int i; - - printk(KERN_ERR "unable to request IRQ %d " - "for DMA (error %d)\n", - omap1_dma_irq[ch], r); - for (i = 0; i < ch; i++) - free_irq(omap1_dma_irq[i], - (void *) (i + 1)); - goto out_free; - } + if (ret != 0) + goto exit_dma_irq_fail; } } @@ -2200,46 +2042,91 @@ static int __init omap_init_dma(void) DMA_DEFAULT_FIFO_DEPTH, 0); if (cpu_class_is_omap2()) { - int irq; - if (cpu_is_omap44xx()) - irq = OMAP44XX_IRQ_SDMA_0; - else - irq = INT_24XX_SDMA_IRQ0; - setup_irq(irq, &omap24xx_dma_irq); - } - - if (cpu_is_omap34xx() || cpu_is_omap44xx()) { - /* Enable smartidle idlemodes and autoidle */ - u32 v = dma_read(OCP_SYSCONFIG); - v &= ~(DMA_SYSCONFIG_MIDLEMODE_MASK | - DMA_SYSCONFIG_SIDLEMODE_MASK | - DMA_SYSCONFIG_AUTOIDLE); - v |= (DMA_SYSCONFIG_MIDLEMODE(DMA_IDLEMODE_SMARTIDLE) | - DMA_SYSCONFIG_SIDLEMODE(DMA_IDLEMODE_SMARTIDLE) | - DMA_SYSCONFIG_AUTOIDLE); - dma_write(v , OCP_SYSCONFIG); - /* reserve dma channels 0 and 1 in high security devices */ - if (cpu_is_omap34xx() && - (omap_type() != OMAP2_DEVICE_TYPE_GP)) { - printk(KERN_INFO "Reserving DMA channels 0 and 1 for " - "HS ROM code\n"); - dma_chan[0].dev_id = 0; - dma_chan[1].dev_id = 1; + strcpy(irq_name, "0"); + dma_irq = platform_get_irq_byname(pdev, irq_name); + if (dma_irq < 0) { + dev_err(&pdev->dev, "failed: request IRQ %d", dma_irq); + goto exit_dma_lch_fail; + } + ret = setup_irq(dma_irq, &omap24xx_dma_irq); + if (ret) { + dev_err(&pdev->dev, "set_up failed for IRQ %d" + "for DMA (error %d)\n", dma_irq, ret); + goto exit_dma_lch_fail; } } + /* reserve dma channels 0 and 1 in high security devices */ + if (cpu_is_omap34xx() && + (omap_type() != OMAP2_DEVICE_TYPE_GP)) { + printk(KERN_INFO "Reserving DMA channels 0 and 1 for " + "HS ROM code\n"); + dma_chan[0].dev_id = 0; + dma_chan[1].dev_id = 1; + } + p->show_dma_caps(); return 0; -out_free: +exit_dma_irq_fail: + dev_err(&pdev->dev, "unable to request IRQ %d" + "for DMA (error %d)\n", dma_irq, ret); + for (irq_rel = 0; irq_rel < ch; irq_rel++) { + dma_irq = platform_get_irq(pdev, irq_rel); + free_irq(dma_irq, (void *)(irq_rel + 1)); + } + +exit_dma_lch_fail: + kfree(p); + kfree(d); kfree(dma_chan); + return ret; +} -out_unmap: - iounmap(omap_dma_base); +static int __devexit omap_system_dma_remove(struct platform_device *pdev) +{ + int dma_irq; - return r; + if (cpu_class_is_omap2()) { + char irq_name[4]; + strcpy(irq_name, "0"); + dma_irq = platform_get_irq_byname(pdev, irq_name); + remove_irq(dma_irq, &omap24xx_dma_irq); + } else { + int irq_rel = 0; + for ( ; irq_rel < dma_chan_count; irq_rel++) { + dma_irq = platform_get_irq(pdev, irq_rel); + free_irq(dma_irq, (void *)(irq_rel + 1)); + } + } + kfree(p); + kfree(d); + kfree(dma_chan); + return 0; +} + +static struct platform_driver omap_system_dma_driver = { + .probe = omap_system_dma_probe, + .remove = omap_system_dma_remove, + .driver = { + .name = "omap_dma_system" + }, +}; + +static int __init omap_system_dma_init(void) +{ + return platform_driver_register(&omap_system_dma_driver); +} +arch_initcall(omap_system_dma_init); + +static void __exit omap_system_dma_exit(void) +{ + platform_driver_unregister(&omap_system_dma_driver); } -arch_initcall(omap_init_dma); +MODULE_DESCRIPTION("OMAP SYSTEM DMA DRIVER"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:" DRIVER_NAME); +MODULE_AUTHOR("Texas Instruments Inc"); /* * Reserve the omap SDMA channels using cmdline bootarg diff --git a/arch/arm/plat-omap/include/plat/dma.h b/arch/arm/plat-omap/include/plat/dma.h index 0cce4ca83aa..d1c916fcf77 100644 --- a/arch/arm/plat-omap/include/plat/dma.h +++ b/arch/arm/plat-omap/include/plat/dma.h @@ -21,141 +21,15 @@ #ifndef __ASM_ARCH_DMA_H #define __ASM_ARCH_DMA_H -/* Move omap4 specific defines to dma-44xx.h */ -#include "dma-44xx.h" +#include <linux/platform_device.h> -/* Hardware registers for omap1 */ -#define OMAP1_DMA_BASE (0xfffed800) - -#define OMAP1_DMA_GCR 0x400 -#define OMAP1_DMA_GSCR 0x404 -#define OMAP1_DMA_GRST 0x408 -#define OMAP1_DMA_HW_ID 0x442 -#define OMAP1_DMA_PCH2_ID 0x444 -#define OMAP1_DMA_PCH0_ID 0x446 -#define OMAP1_DMA_PCH1_ID 0x448 -#define OMAP1_DMA_PCHG_ID 0x44a -#define OMAP1_DMA_PCHD_ID 0x44c -#define OMAP1_DMA_CAPS_0_U 0x44e -#define OMAP1_DMA_CAPS_0_L 0x450 -#define OMAP1_DMA_CAPS_1_U 0x452 -#define OMAP1_DMA_CAPS_1_L 0x454 -#define OMAP1_DMA_CAPS_2 0x456 -#define OMAP1_DMA_CAPS_3 0x458 -#define OMAP1_DMA_CAPS_4 0x45a -#define OMAP1_DMA_PCH2_SR 0x460 -#define OMAP1_DMA_PCH0_SR 0x480 -#define OMAP1_DMA_PCH1_SR 0x482 -#define OMAP1_DMA_PCHD_SR 0x4c0 - -/* Hardware registers for omap2 and omap3 */ -#define OMAP24XX_DMA4_BASE (L4_24XX_BASE + 0x56000) -#define OMAP34XX_DMA4_BASE (L4_34XX_BASE + 0x56000) -#define OMAP44XX_DMA4_BASE (L4_44XX_BASE + 0x56000) - -#define OMAP_DMA4_REVISION 0x00 -#define OMAP_DMA4_GCR 0x78 -#define OMAP_DMA4_IRQSTATUS_L0 0x08 -#define OMAP_DMA4_IRQSTATUS_L1 0x0c -#define OMAP_DMA4_IRQSTATUS_L2 0x10 -#define OMAP_DMA4_IRQSTATUS_L3 0x14 -#define OMAP_DMA4_IRQENABLE_L0 0x18 -#define OMAP_DMA4_IRQENABLE_L1 0x1c -#define OMAP_DMA4_IRQENABLE_L2 0x20 -#define OMAP_DMA4_IRQENABLE_L3 0x24 -#define OMAP_DMA4_SYSSTATUS 0x28 -#define OMAP_DMA4_OCP_SYSCONFIG 0x2c -#define OMAP_DMA4_CAPS_0 0x64 -#define OMAP_DMA4_CAPS_2 0x6c -#define OMAP_DMA4_CAPS_3 0x70 -#define OMAP_DMA4_CAPS_4 0x74 - -#define OMAP1_LOGICAL_DMA_CH_COUNT 17 -#define OMAP_DMA4_LOGICAL_DMA_CH_COUNT 32 /* REVISIT: Is this 32 + 2? */ - -/* Common channel specific registers for omap1 */ -#define OMAP1_DMA_CH_BASE(n) (0x40 * (n) + 0x00) -#define OMAP1_DMA_CSDP(n) (0x40 * (n) + 0x00) -#define OMAP1_DMA_CCR(n) (0x40 * (n) + 0x02) -#define OMAP1_DMA_CICR(n) (0x40 * (n) + 0x04) -#define OMAP1_DMA_CSR(n) (0x40 * (n) + 0x06) -#define OMAP1_DMA_CEN(n) (0x40 * (n) + 0x10) -#define OMAP1_DMA_CFN(n) (0x40 * (n) + 0x12) -#define OMAP1_DMA_CSFI(n) (0x40 * (n) + 0x14) -#define OMAP1_DMA_CSEI(n) (0x40 * (n) + 0x16) -#define OMAP1_DMA_CPC(n) (0x40 * (n) + 0x18) /* 15xx only */ -#define OMAP1_DMA_CSAC(n) (0x40 * (n) + 0x18) -#define OMAP1_DMA_CDAC(n) (0x40 * (n) + 0x1a) -#define OMAP1_DMA_CDEI(n) (0x40 * (n) + 0x1c) -#define OMAP1_DMA_CDFI(n) (0x40 * (n) + 0x1e) -#define OMAP1_DMA_CLNK_CTRL(n) (0x40 * (n) + 0x28) - -/* Common channel specific registers for omap2 */ -#define OMAP_DMA4_CH_BASE(n) (0x60 * (n) + 0x80) -#define OMAP_DMA4_CCR(n) (0x60 * (n) + 0x80) -#define OMAP_DMA4_CLNK_CTRL(n) (0x60 * (n) + 0x84) -#define OMAP_DMA4_CICR(n) (0x60 * (n) + 0x88) -#define OMAP_DMA4_CSR(n) (0x60 * (n) + 0x8c) -#define OMAP_DMA4_CSDP(n) (0x60 * (n) + 0x90) -#define OMAP_DMA4_CEN(n) (0x60 * (n) + 0x94) -#define OMAP_DMA4_CFN(n) (0x60 * (n) + 0x98) -#define OMAP_DMA4_CSEI(n) (0x60 * (n) + 0xa4) -#define OMAP_DMA4_CSFI(n) (0x60 * (n) + 0xa8) -#define OMAP_DMA4_CDEI(n) (0x60 * (n) + 0xac) -#define OMAP_DMA4_CDFI(n) (0x60 * (n) + 0xb0) -#define OMAP_DMA4_CSAC(n) (0x60 * (n) + 0xb4) -#define OMAP_DMA4_CDAC(n) (0x60 * (n) + 0xb8) - -/* Channel specific registers only on omap1 */ -#define OMAP1_DMA_CSSA_L(n) (0x40 * (n) + 0x08) -#define OMAP1_DMA_CSSA_U(n) (0x40 * (n) + 0x0a) -#define OMAP1_DMA_CDSA_L(n) (0x40 * (n) + 0x0c) -#define OMAP1_DMA_CDSA_U(n) (0x40 * (n) + 0x0e) -#define OMAP1_DMA_COLOR_L(n) (0x40 * (n) + 0x20) -#define OMAP1_DMA_COLOR_U(n) (0x40 * (n) + 0x22) -#define OMAP1_DMA_CCR2(n) (0x40 * (n) + 0x24) -#define OMAP1_DMA_LCH_CTRL(n) (0x40 * (n) + 0x2a) /* not on 15xx */ -#define OMAP1_DMA_CCEN(n) 0 -#define OMAP1_DMA_CCFN(n) 0 - -/* Channel specific registers only on omap2 */ -#define OMAP_DMA4_CSSA(n) (0x60 * (n) + 0x9c) -#define OMAP_DMA4_CDSA(n) (0x60 * (n) + 0xa0) -#define OMAP_DMA4_CCEN(n) (0x60 * (n) + 0xbc) -#define OMAP_DMA4_CCFN(n) (0x60 * (n) + 0xc0) -#define OMAP_DMA4_COLOR(n) (0x60 * (n) + 0xc4) - -/* Additional registers available on OMAP4 */ -#define OMAP_DMA4_CDP(n) (0x60 * (n) + 0xd0) -#define OMAP_DMA4_CNDP(n) (0x60 * (n) + 0xd4) -#define OMAP_DMA4_CCDN(n) (0x60 * (n) + 0xd8) - -/* Dummy defines to keep multi-omap compiles happy */ -#define OMAP1_DMA_REVISION 0 -#define OMAP1_DMA_IRQSTATUS_L0 0 -#define OMAP1_DMA_IRQENABLE_L0 0 -#define OMAP1_DMA_OCP_SYSCONFIG 0 -#define OMAP_DMA4_HW_ID 0 -#define OMAP_DMA4_CAPS_0_L 0 -#define OMAP_DMA4_CAPS_0_U 0 -#define OMAP_DMA4_CAPS_1_L 0 -#define OMAP_DMA4_CAPS_1_U 0 -#define OMAP_DMA4_GSCR 0 -#define OMAP_DMA4_CPC(n) 0 - -#define OMAP_DMA4_LCH_CTRL(n) 0 -#define OMAP_DMA4_COLOR_L(n) 0 -#define OMAP_DMA4_COLOR_U(n) 0 -#define OMAP_DMA4_CCR2(n) 0 -#define OMAP1_DMA_CSSA(n) 0 -#define OMAP1_DMA_CDSA(n) 0 -#define OMAP_DMA4_CSSA_L(n) 0 -#define OMAP_DMA4_CSSA_U(n) 0 -#define OMAP_DMA4_CDSA_L(n) 0 -#define OMAP_DMA4_CDSA_U(n) 0 -#define OMAP1_DMA_COLOR(n) 0 +/* + * TODO: These dma channel defines should go away once all + * the omap drivers hwmod adapted. + */ -/*----------------------------------------------------------------------------*/ +/* Move omap4 specific defines to dma-44xx.h */ +#include "dma-44xx.h" /* DMA channels for omap1 */ #define OMAP_DMA_NO_DEVICE 0 @@ -405,6 +279,63 @@ #define DMA_CH_PRIO_HIGH 0x1 #define DMA_CH_PRIO_LOW 0x0 /* Def */ +/* Errata handling */ +#define IS_DMA_ERRATA(id) (errata & (id)) +#define SET_DMA_ERRATA(id) (errata |= (id)) + +#define DMA_ERRATA_IFRAME_BUFFERING BIT(0x0) +#define DMA_ERRATA_PARALLEL_CHANNELS BIT(0x1) +#define DMA_ERRATA_i378 BIT(0x2) +#define DMA_ERRATA_i541 BIT(0x3) +#define DMA_ERRATA_i88 BIT(0x4) +#define DMA_ERRATA_3_3 BIT(0x5) +#define DMA_ROMCODE_BUG BIT(0x6) + +/* Attributes for OMAP DMA Contrller */ +#define DMA_LINKED_LCH BIT(0x0) +#define GLOBAL_PRIORITY BIT(0x1) +#define RESERVE_CHANNEL BIT(0x2) +#define IS_CSSA_32 BIT(0x3) +#define IS_CDSA_32 BIT(0x4) +#define IS_RW_PRIORITY BIT(0x5) +#define ENABLE_1510_MODE BIT(0x6) +#define SRC_PORT BIT(0x7) +#define DST_PORT BIT(0x8) +#define SRC_INDEX BIT(0x9) +#define DST_INDEX BIT(0xA) +#define IS_BURST_ONLY4 BIT(0xB) +#define CLEAR_CSR_ON_READ BIT(0xC) +#define IS_WORD_16 BIT(0xD) + +enum omap_reg_offsets { + +GCR, GSCR, GRST1, HW_ID, +PCH2_ID, PCH0_ID, PCH1_ID, PCHG_ID, +PCHD_ID, CAPS_0, CAPS_1, CAPS_2, +CAPS_3, CAPS_4, PCH2_SR, PCH0_SR, +PCH1_SR, PCHD_SR, REVISION, IRQSTATUS_L0, +IRQSTATUS_L1, IRQSTATUS_L2, IRQSTATUS_L3, IRQENABLE_L0, +IRQENABLE_L1, IRQENABLE_L2, IRQENABLE_L3, SYSSTATUS, +OCP_SYSCONFIG, + +/* omap1+ specific */ +CPC, CCR2, LCH_CTRL, + +/* Common registers for all omap's */ +CSDP, CCR, CICR, CSR, +CEN, CFN, CSFI, CSEI, +CSAC, CDAC, CDEI, +CDFI, CLNK_CTRL, + +/* Channel specific registers */ +CSSA, CDSA, COLOR, +CCEN, CCFN, + +/* omap3630 and omap4 specific */ +CDP, CNDP, CCDN, + +}; + enum omap_dma_burst_mode { OMAP_DMA_DATA_BURST_DIS = 0, OMAP_DMA_DATA_BURST_4, @@ -470,6 +401,41 @@ struct omap_dma_channel_params { #endif }; +struct omap_dma_lch { + int next_lch; + int dev_id; + u16 saved_csr; + u16 enabled_irqs; + const char *dev_name; + void (*callback)(int lch, u16 ch_status, void *data); + void *data; + long flags; + /* required for Dynamic chaining */ + int prev_linked_ch; + int next_linked_ch; + int state; + int chain_id; + int status; +}; + +struct omap_dma_dev_attr { + u32 dev_caps; + u16 lch_count; + u16 chan_count; + struct omap_dma_lch *chan; +}; + +/* System DMA platform data structure */ +struct omap_system_dma_plat_info { + struct omap_dma_dev_attr *dma_attr; + u32 errata; + void (*disable_irq_lch)(int lch); + void (*show_dma_caps)(void); + void (*clear_lch_regs)(int lch); + void (*clear_dma)(int lch); + void (*dma_write)(u32 val, int reg, int lch); + u32 (*dma_read)(int reg, int lch); +}; extern void omap_set_dma_priority(int lch, int dst_port, int priority); extern int omap_request_dma(int dev_id, const char *dev_name, diff --git a/arch/arm/plat-omap/include/plat/keypad.h b/arch/arm/plat-omap/include/plat/keypad.h index 3ae52ccc793..793ce9d5329 100644 --- a/arch/arm/plat-omap/include/plat/keypad.h +++ b/arch/arm/plat-omap/include/plat/keypad.h @@ -10,16 +10,18 @@ #ifndef ASMARM_ARCH_KEYPAD_H #define ASMARM_ARCH_KEYPAD_H -#warning: Please update the board to use matrix_keypad.h instead +#ifndef CONFIG_ARCH_OMAP1 +#warning Please update the board to use matrix-keypad driver +#endif +#include <linux/input/matrix_keypad.h> struct omap_kp_platform_data { int rows; int cols; - int *keymap; - unsigned int keymapsize; - unsigned int rep:1; + const struct matrix_keymap_data *keymap_data; + bool rep; unsigned long delay; - unsigned int dbounce:1; + bool dbounce; /* specific to OMAP242x*/ unsigned int *row_gpios; unsigned int *col_gpios; @@ -28,18 +30,21 @@ struct omap_kp_platform_data { /* Group (0..3) -- when multiple keys are pressed, only the * keys pressed in the same group are considered as pressed. This is * in order to workaround certain crappy HW designs that produce ghost - * keypresses. */ -#define GROUP_0 (0 << 16) -#define GROUP_1 (1 << 16) -#define GROUP_2 (2 << 16) -#define GROUP_3 (3 << 16) + * keypresses. Two free bits, not used by neither row/col nor keynum, + * must be available for use as group bits. The below GROUP_SHIFT + * macro definition is based on some prior knowledge of the + * matrix_keypad defined KEY() macro internals. + */ +#define GROUP_SHIFT 14 +#define GROUP_0 (0 << GROUP_SHIFT) +#define GROUP_1 (1 << GROUP_SHIFT) +#define GROUP_2 (2 << GROUP_SHIFT) +#define GROUP_3 (3 << GROUP_SHIFT) #define GROUP_MASK GROUP_3 +#if KEY_MAX & GROUP_MASK +#error Group bits in conflict with keynum bits +#endif -#define KEY_PERSISTENT 0x00800000 -#define KEYNUM_MASK 0x00EFFFFF -#define KEY(col, row, val) (((col) << 28) | ((row) << 24) | (val)) -#define PERSISTENT_KEY(col, row) (((col) << 28) | ((row) << 24) | \ - KEY_PERSISTENT) #endif diff --git a/arch/arm/plat-omap/include/plat/omap-pm.h b/arch/arm/plat-omap/include/plat/omap-pm.h index 728fbb9dd54..62c3fe918ab 100644 --- a/arch/arm/plat-omap/include/plat/omap-pm.h +++ b/arch/arm/plat-omap/include/plat/omap-pm.h @@ -17,27 +17,10 @@ #include <linux/device.h> #include <linux/cpufreq.h> #include <linux/clk.h> +#include <linux/opp.h> #include "powerdomain.h" -/** - * struct omap_opp - clock frequency-to-OPP ID table for DSP, MPU - * @rate: target clock rate - * @opp_id: OPP ID - * @min_vdd: minimum VDD1 voltage (in millivolts) for this OPP - * - * Operating performance point data. Can vary by OMAP chip and board. - */ -struct omap_opp { - unsigned long rate; - u8 opp_id; - u16 min_vdd; -}; - -extern struct omap_opp *mpu_opps; -extern struct omap_opp *dsp_opps; -extern struct omap_opp *l3_opps; - /* * agent_id values for use with omap_pm_set_min_bus_tput(): * @@ -59,9 +42,11 @@ extern struct omap_opp *l3_opps; * framework starts. The "_if_" is to avoid name collisions with the * PM idle-loop code. */ -int __init omap_pm_if_early_init(struct omap_opp *mpu_opp_table, - struct omap_opp *dsp_opp_table, - struct omap_opp *l3_opp_table); +#ifdef CONFIG_OMAP_PM_NONE +#define omap_pm_if_early_init() 0 +#else +int __init omap_pm_if_early_init(void); +#endif /** * omap_pm_if_init - OMAP PM init code called after clock fw init @@ -69,7 +54,11 @@ int __init omap_pm_if_early_init(struct omap_opp *mpu_opp_table, * The main initialization code. OPP tables are passed in here. The * "_if_" is to avoid name collisions with the PM idle-loop code. */ +#ifdef CONFIG_OMAP_PM_NONE +#define omap_pm_if_init() 0 +#else int __init omap_pm_if_init(void); +#endif /** * omap_pm_if_exit - OMAP PM exit code diff --git a/arch/arm/plat-omap/include/plat/sram.h b/arch/arm/plat-omap/include/plat/sram.h index 5905100b29a..9967d5e855c 100644 --- a/arch/arm/plat-omap/include/plat/sram.h +++ b/arch/arm/plat-omap/include/plat/sram.h @@ -11,6 +11,7 @@ #ifndef __ARCH_ARM_OMAP_SRAM_H #define __ARCH_ARM_OMAP_SRAM_H +#ifndef __ASSEMBLY__ extern void * omap_sram_push(void * start, unsigned long size); extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl); @@ -74,4 +75,14 @@ extern void omap_push_sram_idle(void); static inline void omap_push_sram_idle(void) {} #endif /* CONFIG_PM */ +#endif /* __ASSEMBLY__ */ + +/* + * OMAP2+: define the SRAM PA addresses. + * Used by the SRAM management code and the idle sleep code. + */ +#define OMAP2_SRAM_PA 0x40200000 +#define OMAP3_SRAM_PA 0x40200000 +#define OMAP4_SRAM_PA 0x40300000 + #endif diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h index 7bbc0740cb4..ad98b85cae2 100644 --- a/arch/arm/plat-omap/include/plat/uncompress.h +++ b/arch/arm/plat-omap/include/plat/uncompress.h @@ -146,6 +146,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) DEBUG_LL_OMAP3(3, cm_t35); DEBUG_LL_OMAP3(3, cm_t3517); DEBUG_LL_OMAP3(3, craneboard); + DEBUG_LL_OMAP3(3, devkit8000); DEBUG_LL_OMAP3(3, igep0020); DEBUG_LL_OMAP3(3, igep0030); DEBUG_LL_OMAP3(3, nokia_rm680); diff --git a/arch/arm/plat-omap/omap-pm-noop.c b/arch/arm/plat-omap/omap-pm-noop.c index e129ce80c53..ca75abb1806 100644 --- a/arch/arm/plat-omap/omap-pm-noop.c +++ b/arch/arm/plat-omap/omap-pm-noop.c @@ -26,10 +26,6 @@ #include <plat/powerdomain.h> -struct omap_opp *dsp_opps; -struct omap_opp *mpu_opps; -struct omap_opp *l3_opps; - /* * Device-driver-originated constraints (via board-*.c files) */ @@ -308,13 +304,8 @@ int omap_pm_get_dev_context_loss_count(struct device *dev) /* Should be called before clk framework init */ -int __init omap_pm_if_early_init(struct omap_opp *mpu_opp_table, - struct omap_opp *dsp_opp_table, - struct omap_opp *l3_opp_table) +int __init omap_pm_if_early_init(void) { - mpu_opps = mpu_opp_table; - dsp_opps = dsp_opp_table; - l3_opps = l3_opp_table; return 0; } diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 819ea0cfb81..1a686c89d8d 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -41,15 +41,12 @@ #define OMAP1_SRAM_PA 0x20000000 #define OMAP1_SRAM_VA VMALLOC_END -#define OMAP2_SRAM_PA 0x40200000 -#define OMAP2_SRAM_PUB_PA 0x4020f800 +#define OMAP2_SRAM_PUB_PA (OMAP2_SRAM_PA + 0xf800) #define OMAP2_SRAM_VA 0xfe400000 #define OMAP2_SRAM_PUB_VA (OMAP2_SRAM_VA + 0x800) -#define OMAP3_SRAM_PA 0x40200000 #define OMAP3_SRAM_VA 0xfe400000 -#define OMAP3_SRAM_PUB_PA 0x40208000 +#define OMAP3_SRAM_PUB_PA (OMAP3_SRAM_PA + 0x8000) #define OMAP3_SRAM_PUB_VA (OMAP3_SRAM_VA + 0x8000) -#define OMAP4_SRAM_PA 0x40300000 #define OMAP4_SRAM_VA 0xfe400000 #define OMAP4_SRAM_PUB_PA (OMAP4_SRAM_PA + 0x4000) #define OMAP4_SRAM_PUB_VA (OMAP4_SRAM_VA + 0x4000) diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig index 5a27b1b538f..eb105e61c74 100644 --- a/arch/arm/plat-s3c24xx/Kconfig +++ b/arch/arm/plat-s3c24xx/Kconfig @@ -8,7 +8,7 @@ config PLAT_S3C24XX default y select NO_IOPORT select ARCH_REQUIRE_GPIOLIB - select S3C_DEVICE_NAND + select S3C_DEV_NAND select S3C_GPIO_CFG_S3C24XX help Base platform code for any Samsung S3C24XX device diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 67a2fa2caa4..0a9b5b8b2a1 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -19,6 +19,8 @@ config MIPS select GENERIC_ATOMIC64 if !64BIT select HAVE_DMA_ATTRS select HAVE_DMA_API_DEBUG + select HAVE_GENERIC_HARDIRQS + select GENERIC_IRQ_PROBE menu "Machine selection" @@ -1664,6 +1666,28 @@ config PAGE_SIZE_64KB endchoice +config FORCE_MAX_ZONEORDER + int "Maximum zone order" + range 13 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB + default "13" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB + range 12 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB + default "12" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB + range 11 64 + default "11" + help + The kernel memory allocator divides physically contiguous memory + blocks into "zones", where each zone is a power of two number of + pages. This option selects the largest power of two that the kernel + keeps in the memory allocator. If you need to allocate very large + blocks of physically contiguous memory, then you may need to + increase this value. + + This config option is actually maximum order plus one. For example, + a value of 11 means that the largest free memory block is 2^10 pages. + + The page size is not necessarily 4KB. Keep this in mind + when choosing a value for this option. + config BOARD_SCACHE bool @@ -1922,20 +1946,6 @@ config CPU_R4400_WORKAROUNDS bool # -# Use the generic interrupt handling code in kernel/irq/: -# -config GENERIC_HARDIRQS - bool - default y - -config GENERIC_IRQ_PROBE - bool - default y - -config IRQ_PER_CPU - bool - -# # - Highmem only makes sense for the 32-bit kernel. # - The current highmem code will only work properly on physically indexed # caches such as R3000, SB1, R7000 or those that look like they're virtually diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c index 3691630931d..9e7814db3d0 100644 --- a/arch/mips/alchemy/common/platform.c +++ b/arch/mips/alchemy/common/platform.c @@ -27,6 +27,7 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state, unsigned int old_state) { +#ifdef CONFIG_SERIAL_8250 switch (state) { case 0: if ((__raw_readl(port->membase + UART_MOD_CNTRL) & 3) != 3) { @@ -49,6 +50,7 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state, serial8250_do_pm(port, state, old_state); break; } +#endif } #define PORT(_base, _irq) \ diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c index b30df5c97ad..baeb2138505 100644 --- a/arch/mips/alchemy/devboards/prom.c +++ b/arch/mips/alchemy/devboards/prom.c @@ -54,10 +54,9 @@ void __init prom_init(void) prom_init_cmdline(); memsize_str = prom_getenv("memsize"); - if (!memsize_str) + if (!memsize_str || strict_strtoul(memsize_str, 0, &memsize)) memsize = ALCHEMY_BOARD_DEFAULT_MEMSIZE; - else - strict_strtoul(memsize_str, 0, &memsize); + add_memory_region(0, memsize, BOOT_MEM_RAM); } diff --git a/arch/mips/ar7/clock.c b/arch/mips/ar7/clock.c index fc0e7154e8d..2ca4ada1c29 100644 --- a/arch/mips/ar7/clock.c +++ b/arch/mips/ar7/clock.c @@ -239,12 +239,12 @@ static void tnetd7300_set_clock(u32 shift, struct tnetd7300_clock *clock, calculate(base_clock, frequency, &prediv, &postdiv, &mul); writel(((prediv - 1) << PREDIV_SHIFT) | (postdiv - 1), &clock->ctrl); - msleep(1); + mdelay(1); writel(4, &clock->pll); while (readl(&clock->pll) & PLL_STATUS) ; writel(((mul - 1) << MUL_SHIFT) | (0xff << 3) | 0x0e, &clock->pll); - msleep(75); + mdelay(75); } static void __init tnetd7300_init_clocks(void) @@ -456,7 +456,7 @@ void clk_put(struct clk *clk) } EXPORT_SYMBOL(clk_put); -int __init ar7_init_clocks(void) +void __init ar7_init_clocks(void) { switch (ar7_chip_id()) { case AR7_CHIP_7100: @@ -472,7 +472,4 @@ int __init ar7_init_clocks(void) } /* adjust vbus clock rate */ vbus_clk.rate = bus_clk.rate / 2; - - return 0; } -arch_initcall(ar7_init_clocks); diff --git a/arch/mips/ar7/time.c b/arch/mips/ar7/time.c index 5fb8a013408..22c93213b23 100644 --- a/arch/mips/ar7/time.c +++ b/arch/mips/ar7/time.c @@ -30,6 +30,9 @@ void __init plat_time_init(void) { struct clk *cpu_clk; + /* Initialize ar7 clocks so the CPU clock frequency is correct */ + ar7_init_clocks(); + cpu_clk = clk_get(NULL, "cpu"); if (IS_ERR(cpu_clk)) { printk(KERN_ERR "unable to get cpu clock\n"); diff --git a/arch/mips/bcm47xx/setup.c b/arch/mips/bcm47xx/setup.c index b1aee33efd1..c95f90bf734 100644 --- a/arch/mips/bcm47xx/setup.c +++ b/arch/mips/bcm47xx/setup.c @@ -32,7 +32,6 @@ #include <asm/reboot.h> #include <asm/time.h> #include <bcm47xx.h> -#include <asm/fw/cfe/cfe_api.h> #include <asm/mach-bcm47xx/nvram.h> struct ssb_bus ssb_bcm47xx; @@ -57,68 +56,112 @@ static void bcm47xx_machine_halt(void) cpu_relax(); } -static void str2eaddr(char *str, char *dest) -{ - int i = 0; +#define READ_FROM_NVRAM(_outvar, name, buf) \ + if (nvram_getenv(name, buf, sizeof(buf)) >= 0)\ + sprom->_outvar = simple_strtoul(buf, NULL, 0); - if (str == NULL) { - memset(dest, 0, 6); - return; +static void bcm47xx_fill_sprom(struct ssb_sprom *sprom) +{ + char buf[100]; + u32 boardflags; + + memset(sprom, 0, sizeof(struct ssb_sprom)); + + sprom->revision = 1; /* Fallback: Old hardware does not define this. */ + READ_FROM_NVRAM(revision, "sromrev", buf); + if (nvram_getenv("il0macaddr", buf, sizeof(buf)) >= 0) + nvram_parse_macaddr(buf, sprom->il0mac); + if (nvram_getenv("et0macaddr", buf, sizeof(buf)) >= 0) + nvram_parse_macaddr(buf, sprom->et0mac); + if (nvram_getenv("et1macaddr", buf, sizeof(buf)) >= 0) + nvram_parse_macaddr(buf, sprom->et1mac); + READ_FROM_NVRAM(et0phyaddr, "et0phyaddr", buf); + READ_FROM_NVRAM(et1phyaddr, "et1phyaddr", buf); + READ_FROM_NVRAM(et0mdcport, "et0mdcport", buf); + READ_FROM_NVRAM(et1mdcport, "et1mdcport", buf); + READ_FROM_NVRAM(board_rev, "boardrev", buf); + READ_FROM_NVRAM(country_code, "ccode", buf); + READ_FROM_NVRAM(ant_available_a, "aa5g", buf); + READ_FROM_NVRAM(ant_available_bg, "aa2g", buf); + READ_FROM_NVRAM(pa0b0, "pa0b0", buf); + READ_FROM_NVRAM(pa0b1, "pa0b1", buf); + READ_FROM_NVRAM(pa0b2, "pa0b2", buf); + READ_FROM_NVRAM(pa1b0, "pa1b0", buf); + READ_FROM_NVRAM(pa1b1, "pa1b1", buf); + READ_FROM_NVRAM(pa1b2, "pa1b2", buf); + READ_FROM_NVRAM(pa1lob0, "pa1lob0", buf); + READ_FROM_NVRAM(pa1lob2, "pa1lob1", buf); + READ_FROM_NVRAM(pa1lob1, "pa1lob2", buf); + READ_FROM_NVRAM(pa1hib0, "pa1hib0", buf); + READ_FROM_NVRAM(pa1hib2, "pa1hib1", buf); + READ_FROM_NVRAM(pa1hib1, "pa1hib2", buf); + READ_FROM_NVRAM(gpio0, "wl0gpio0", buf); + READ_FROM_NVRAM(gpio1, "wl0gpio1", buf); + READ_FROM_NVRAM(gpio2, "wl0gpio2", buf); + READ_FROM_NVRAM(gpio3, "wl0gpio3", buf); + READ_FROM_NVRAM(maxpwr_bg, "pa0maxpwr", buf); + READ_FROM_NVRAM(maxpwr_al, "pa1lomaxpwr", buf); + READ_FROM_NVRAM(maxpwr_a, "pa1maxpwr", buf); + READ_FROM_NVRAM(maxpwr_ah, "pa1himaxpwr", buf); + READ_FROM_NVRAM(itssi_a, "pa1itssit", buf); + READ_FROM_NVRAM(itssi_bg, "pa0itssit", buf); + READ_FROM_NVRAM(tri2g, "tri2g", buf); + READ_FROM_NVRAM(tri5gl, "tri5gl", buf); + READ_FROM_NVRAM(tri5g, "tri5g", buf); + READ_FROM_NVRAM(tri5gh, "tri5gh", buf); + READ_FROM_NVRAM(rxpo2g, "rxpo2g", buf); + READ_FROM_NVRAM(rxpo5g, "rxpo5g", buf); + READ_FROM_NVRAM(rssisav2g, "rssisav2g", buf); + READ_FROM_NVRAM(rssismc2g, "rssismc2g", buf); + READ_FROM_NVRAM(rssismf2g, "rssismf2g", buf); + READ_FROM_NVRAM(bxa2g, "bxa2g", buf); + READ_FROM_NVRAM(rssisav5g, "rssisav5g", buf); + READ_FROM_NVRAM(rssismc5g, "rssismc5g", buf); + READ_FROM_NVRAM(rssismf5g, "rssismf5g", buf); + READ_FROM_NVRAM(bxa5g, "bxa5g", buf); + READ_FROM_NVRAM(cck2gpo, "cck2gpo", buf); + READ_FROM_NVRAM(ofdm2gpo, "ofdm2gpo", buf); + READ_FROM_NVRAM(ofdm5glpo, "ofdm5glpo", buf); + READ_FROM_NVRAM(ofdm5gpo, "ofdm5gpo", buf); + READ_FROM_NVRAM(ofdm5ghpo, "ofdm5ghpo", buf); + + if (nvram_getenv("boardflags", buf, sizeof(buf)) >= 0) { + boardflags = simple_strtoul(buf, NULL, 0); + if (boardflags) { + sprom->boardflags_lo = (boardflags & 0x0000FFFFU); + sprom->boardflags_hi = (boardflags & 0xFFFF0000U) >> 16; + } } - - for (;;) { - dest[i++] = (char) simple_strtoul(str, NULL, 16); - str += 2; - if (!*str++ || i == 6) - break; + if (nvram_getenv("boardflags2", buf, sizeof(buf)) >= 0) { + boardflags = simple_strtoul(buf, NULL, 0); + if (boardflags) { + sprom->boardflags2_lo = (boardflags & 0x0000FFFFU); + sprom->boardflags2_hi = (boardflags & 0xFFFF0000U) >> 16; + } } } static int bcm47xx_get_invariants(struct ssb_bus *bus, struct ssb_init_invariants *iv) { - char buf[100]; + char buf[20]; /* Fill boardinfo structure */ memset(&(iv->boardinfo), 0 , sizeof(struct ssb_boardinfo)); - if (cfe_getenv("boardvendor", buf, sizeof(buf)) >= 0 || - nvram_getenv("boardvendor", buf, sizeof(buf)) >= 0) - iv->boardinfo.type = (u16)simple_strtoul(buf, NULL, 0); - if (cfe_getenv("boardtype", buf, sizeof(buf)) >= 0 || - nvram_getenv("boardtype", buf, sizeof(buf)) >= 0) + if (nvram_getenv("boardvendor", buf, sizeof(buf)) >= 0) + iv->boardinfo.vendor = (u16)simple_strtoul(buf, NULL, 0); + else + iv->boardinfo.vendor = SSB_BOARDVENDOR_BCM; + if (nvram_getenv("boardtype", buf, sizeof(buf)) >= 0) iv->boardinfo.type = (u16)simple_strtoul(buf, NULL, 0); - if (cfe_getenv("boardrev", buf, sizeof(buf)) >= 0 || - nvram_getenv("boardrev", buf, sizeof(buf)) >= 0) + if (nvram_getenv("boardrev", buf, sizeof(buf)) >= 0) iv->boardinfo.rev = (u16)simple_strtoul(buf, NULL, 0); - /* Fill sprom structure */ - memset(&(iv->sprom), 0, sizeof(struct ssb_sprom)); - iv->sprom.revision = 3; - - if (cfe_getenv("et0macaddr", buf, sizeof(buf)) >= 0 || - nvram_getenv("et0macaddr", buf, sizeof(buf)) >= 0) - str2eaddr(buf, iv->sprom.et0mac); + bcm47xx_fill_sprom(&iv->sprom); - if (cfe_getenv("et1macaddr", buf, sizeof(buf)) >= 0 || - nvram_getenv("et1macaddr", buf, sizeof(buf)) >= 0) - str2eaddr(buf, iv->sprom.et1mac); - - if (cfe_getenv("et0phyaddr", buf, sizeof(buf)) >= 0 || - nvram_getenv("et0phyaddr", buf, sizeof(buf)) >= 0) - iv->sprom.et0phyaddr = simple_strtoul(buf, NULL, 0); - - if (cfe_getenv("et1phyaddr", buf, sizeof(buf)) >= 0 || - nvram_getenv("et1phyaddr", buf, sizeof(buf)) >= 0) - iv->sprom.et1phyaddr = simple_strtoul(buf, NULL, 0); - - if (cfe_getenv("et0mdcport", buf, sizeof(buf)) >= 0 || - nvram_getenv("et0mdcport", buf, sizeof(buf)) >= 0) - iv->sprom.et0mdcport = simple_strtoul(buf, NULL, 10); - - if (cfe_getenv("et1mdcport", buf, sizeof(buf)) >= 0 || - nvram_getenv("et1mdcport", buf, sizeof(buf)) >= 0) - iv->sprom.et1mdcport = simple_strtoul(buf, NULL, 10); + if (nvram_getenv("cardbus", buf, sizeof(buf)) >= 0) + iv->has_cardbus_slot = !!simple_strtoul(buf, NULL, 10); return 0; } @@ -126,12 +169,28 @@ static int bcm47xx_get_invariants(struct ssb_bus *bus, void __init plat_mem_setup(void) { int err; + char buf[100]; + struct ssb_mipscore *mcore; err = ssb_bus_ssbbus_register(&ssb_bcm47xx, SSB_ENUM_BASE, bcm47xx_get_invariants); if (err) panic("Failed to initialize SSB bus (err %d)\n", err); + mcore = &ssb_bcm47xx.mipscore; + if (nvram_getenv("kernel_args", buf, sizeof(buf)) >= 0) { + if (strstr(buf, "console=ttyS1")) { + struct ssb_serial_port port; + + printk(KERN_DEBUG "Swapping serial ports!\n"); + /* swap serial ports */ + memcpy(&port, &mcore->serial_ports[0], sizeof(port)); + memcpy(&mcore->serial_ports[0], &mcore->serial_ports[1], + sizeof(port)); + memcpy(&mcore->serial_ports[1], &port, sizeof(port)); + } + } + _machine_restart = bcm47xx_machine_restart; _machine_halt = bcm47xx_machine_halt; pm_power_off = bcm47xx_machine_halt; diff --git a/arch/mips/include/asm/cpu.h b/arch/mips/include/asm/cpu.h index 06d59dcbe24..86877539c6e 100644 --- a/arch/mips/include/asm/cpu.h +++ b/arch/mips/include/asm/cpu.h @@ -111,8 +111,8 @@ * These are the PRID's for when 23:16 == PRID_COMP_BROADCOM */ -#define PRID_IMP_BMIPS4KC 0x4000 -#define PRID_IMP_BMIPS32 0x8000 +#define PRID_IMP_BMIPS32_REV4 0x4000 +#define PRID_IMP_BMIPS32_REV8 0x8000 #define PRID_IMP_BMIPS3300 0x9000 #define PRID_IMP_BMIPS3300_ALT 0x9100 #define PRID_IMP_BMIPS3300_BUG 0x0000 diff --git a/arch/mips/include/asm/elf.h b/arch/mips/include/asm/elf.h index fd1d39eb743..455c0ac7d4e 100644 --- a/arch/mips/include/asm/elf.h +++ b/arch/mips/include/asm/elf.h @@ -249,7 +249,8 @@ extern struct mips_abi mips_abi_n32; #define SET_PERSONALITY(ex) \ do { \ - set_personality(PER_LINUX); \ + if (personality(current->personality) != PER_LINUX) \ + set_personality(PER_LINUX); \ \ current->thread.abi = &mips_abi; \ } while (0) @@ -296,6 +297,8 @@ do { \ #define SET_PERSONALITY(ex) \ do { \ + unsigned int p; \ + \ clear_thread_flag(TIF_32BIT_REGS); \ clear_thread_flag(TIF_32BIT_ADDR); \ \ @@ -304,7 +307,8 @@ do { \ else \ current->thread.abi = &mips_abi; \ \ - if (current->personality != PER_LINUX32) \ + p = personality(current->personality); \ + if (p != PER_LINUX32 && p != PER_LINUX) \ set_personality(PER_LINUX); \ } while (0) diff --git a/arch/mips/include/asm/io.h b/arch/mips/include/asm/io.h index c98bf514ec7..5b017f23e24 100644 --- a/arch/mips/include/asm/io.h +++ b/arch/mips/include/asm/io.h @@ -329,10 +329,14 @@ static inline void pfx##write##bwlq(type val, \ "dsrl32 %L0, %L0, 0" "\n\t" \ "dsll32 %M0, %M0, 0" "\n\t" \ "or %L0, %L0, %M0" "\n\t" \ + ".set push" "\n\t" \ + ".set noreorder" "\n\t" \ + ".set nomacro" "\n\t" \ "sd %L0, %2" "\n\t" \ + ".set pop" "\n\t" \ ".set mips0" "\n" \ : "=r" (__tmp) \ - : "0" (__val), "m" (*__mem)); \ + : "0" (__val), "R" (*__mem)); \ if (irq) \ local_irq_restore(__flags); \ } else \ @@ -355,12 +359,16 @@ static inline type pfx##read##bwlq(const volatile void __iomem *mem) \ local_irq_save(__flags); \ __asm__ __volatile__( \ ".set mips3" "\t\t# __readq" "\n\t" \ + ".set push" "\n\t" \ + ".set noreorder" "\n\t" \ + ".set nomacro" "\n\t" \ "ld %L0, %1" "\n\t" \ + ".set pop" "\n\t" \ "dsra32 %M0, %L0, 0" "\n\t" \ "sll %L0, %L0, 0" "\n\t" \ ".set mips0" "\n" \ : "=r" (__val) \ - : "m" (*__mem)); \ + : "R" (*__mem)); \ if (irq) \ local_irq_restore(__flags); \ } else { \ diff --git a/arch/mips/include/asm/mach-ar7/ar7.h b/arch/mips/include/asm/mach-ar7/ar7.h index 7919d76186b..07d3fadb244 100644 --- a/arch/mips/include/asm/mach-ar7/ar7.h +++ b/arch/mips/include/asm/mach-ar7/ar7.h @@ -201,7 +201,6 @@ static inline void ar7_device_off(u32 bit) } int __init ar7_gpio_init(void); - -int __init ar7_gpio_init(void); +void __init ar7_init_clocks(void); #endif /* __AR7_H__ */ diff --git a/arch/mips/include/asm/mach-bcm47xx/nvram.h b/arch/mips/include/asm/mach-bcm47xx/nvram.h index c58ebd8bc15..9759588ba3c 100644 --- a/arch/mips/include/asm/mach-bcm47xx/nvram.h +++ b/arch/mips/include/asm/mach-bcm47xx/nvram.h @@ -12,6 +12,7 @@ #define __NVRAM_H #include <linux/types.h> +#include <linux/kernel.h> struct nvram_header { u32 magic; @@ -36,4 +37,10 @@ struct nvram_header { extern int nvram_getenv(char *name, char *val, size_t val_len); +static inline void nvram_parse_macaddr(char *buf, u8 *macaddr) +{ + sscanf(buf, "%hhx:%hhx:%hhx:%hhx:%hhx:%hhx", &macaddr[0], &macaddr[1], + &macaddr[2], &macaddr[3], &macaddr[4], &macaddr[5]); +} + #endif diff --git a/arch/mips/jz4740/board-qi_lb60.c b/arch/mips/jz4740/board-qi_lb60.c index 5742bb4d78f..5c0a3575877 100644 --- a/arch/mips/jz4740/board-qi_lb60.c +++ b/arch/mips/jz4740/board-qi_lb60.c @@ -5,7 +5,7 @@ * * Copyright (c) 2009 Qi Hardware inc., * Author: Xiangfu Liu <xiangfu@qi-hardware.com> - * Copyright 2010, Lars-Petrer Clausen <lars@metafoo.de> + * Copyright 2010, Lars-Peter Clausen <lars@metafoo.de> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 or later @@ -235,7 +235,7 @@ static const unsigned int qi_lb60_keypad_rows[] = { QI_LB60_GPIO_KEYIN(3), QI_LB60_GPIO_KEYIN(4), QI_LB60_GPIO_KEYIN(5), - QI_LB60_GPIO_KEYIN(7), + QI_LB60_GPIO_KEYIN(6), QI_LB60_GPIO_KEYIN8, }; diff --git a/arch/mips/jz4740/platform.c b/arch/mips/jz4740/platform.c index 95bc2b5b14f..1cc9e544d16 100644 --- a/arch/mips/jz4740/platform.c +++ b/arch/mips/jz4740/platform.c @@ -208,7 +208,7 @@ struct platform_device jz4740_i2s_device = { /* PCM */ struct platform_device jz4740_pcm_device = { - .name = "jz4740-pcm", + .name = "jz4740-pcm-audio", .id = -1, }; diff --git a/arch/mips/jz4740/prom.c b/arch/mips/jz4740/prom.c index cfeac15eb2e..4a70407f55b 100644 --- a/arch/mips/jz4740/prom.c +++ b/arch/mips/jz4740/prom.c @@ -23,7 +23,7 @@ #include <asm/bootinfo.h> #include <asm/mach-jz4740/base.h> -void jz4740_init_cmdline(int argc, char *argv[]) +static __init void jz4740_init_cmdline(int argc, char *argv[]) { unsigned int count = COMMAND_LINE_SIZE - 1; int i; diff --git a/arch/mips/kernel/cevt-r4k.c b/arch/mips/kernel/cevt-r4k.c index 2f4d7a99bcc..98c5a9737c1 100644 --- a/arch/mips/kernel/cevt-r4k.c +++ b/arch/mips/kernel/cevt-r4k.c @@ -32,7 +32,7 @@ static int mips_next_event(unsigned long delta, cnt = read_c0_count(); cnt += delta; write_c0_compare(cnt); - res = ((int)(read_c0_count() - cnt) > 0) ? -ETIME : 0; + res = ((int)(read_c0_count() - cnt) >= 0) ? -ETIME : 0; return res; } diff --git a/arch/mips/kernel/cpu-probe.c b/arch/mips/kernel/cpu-probe.c index 71620e19827..68dae7b6b5d 100644 --- a/arch/mips/kernel/cpu-probe.c +++ b/arch/mips/kernel/cpu-probe.c @@ -905,7 +905,8 @@ static inline void cpu_probe_broadcom(struct cpuinfo_mips *c, unsigned int cpu) { decode_configs(c); switch (c->processor_id & 0xff00) { - case PRID_IMP_BMIPS32: + case PRID_IMP_BMIPS32_REV4: + case PRID_IMP_BMIPS32_REV8: c->cputype = CPU_BMIPS32; __cpu_name[cpu] = "Broadcom BMIPS32"; break; @@ -933,10 +934,6 @@ static inline void cpu_probe_broadcom(struct cpuinfo_mips *c, unsigned int cpu) __cpu_name[cpu] = "Broadcom BMIPS5000"; c->options |= MIPS_CPU_ULRI; break; - case PRID_IMP_BMIPS4KC: - c->cputype = CPU_4KC; - __cpu_name[cpu] = "MIPS 4Kc"; - break; } } diff --git a/arch/mips/kernel/linux32.c b/arch/mips/kernel/linux32.c index 6343b4a5b83..876a75cc376 100644 --- a/arch/mips/kernel/linux32.c +++ b/arch/mips/kernel/linux32.c @@ -251,14 +251,15 @@ SYSCALL_DEFINE5(n32_msgrcv, int, msqid, u32, msgp, size_t, msgsz, SYSCALL_DEFINE1(32_personality, unsigned long, personality) { + unsigned int p = personality & 0xffffffff; int ret; - personality &= 0xffffffff; + if (personality(current->personality) == PER_LINUX32 && - personality == PER_LINUX) - personality = PER_LINUX32; - ret = sys_personality(personality); - if (ret == PER_LINUX32) - ret = PER_LINUX; + personality(p) == PER_LINUX) + p = (p & ~PER_MASK) | PER_LINUX32; + ret = sys_personality(p); + if (ret != -1 && personality(ret) == PER_LINUX32) + ret = (ret & ~PER_MASK) | PER_LINUX; return ret; } diff --git a/arch/mips/kernel/process.c b/arch/mips/kernel/process.c index 99960940d4a..ae167df73dd 100644 --- a/arch/mips/kernel/process.c +++ b/arch/mips/kernel/process.c @@ -142,7 +142,6 @@ int copy_thread(unsigned long clone_flags, unsigned long usp, childregs->regs[7] = 0; /* Clear error flag */ childregs->regs[2] = 0; /* Child gets zero as return value */ - regs->regs[2] = p->pid; if (childregs->cp0_status & ST0_CU0) { childregs->regs[28] = (unsigned long) ti; diff --git a/arch/mips/kernel/prom.c b/arch/mips/kernel/prom.c index e000b278f02..9dbe5836895 100644 --- a/arch/mips/kernel/prom.c +++ b/arch/mips/kernel/prom.c @@ -100,7 +100,7 @@ void __init device_tree_init(void) return; base = virt_to_phys((void *)initial_boot_params); - size = initial_boot_params->totalsize; + size = be32_to_cpu(initial_boot_params->totalsize); /* Before we do anything, lets reserve the dt blob */ reserve_mem_mach(base, size); diff --git a/arch/mips/kernel/smp-mt.c b/arch/mips/kernel/smp-mt.c index 43e7cdc5ded..c0e81418ba2 100644 --- a/arch/mips/kernel/smp-mt.c +++ b/arch/mips/kernel/smp-mt.c @@ -153,7 +153,7 @@ static void __cpuinit vsmp_init_secondary(void) { extern int gic_present; - /* This is Malta specific: IPI,performance and timer inetrrupts */ + /* This is Malta specific: IPI,performance and timer interrupts */ if (gic_present) change_c0_status(ST0_IM, STATUSF_IP3 | STATUSF_IP4 | STATUSF_IP6 | STATUSF_IP7); diff --git a/arch/mips/kernel/traps.c b/arch/mips/kernel/traps.c index 8e9fbe75894..e9710430254 100644 --- a/arch/mips/kernel/traps.c +++ b/arch/mips/kernel/traps.c @@ -83,7 +83,8 @@ extern asmlinkage void handle_mcheck(void); extern asmlinkage void handle_reserved(void); extern int fpu_emulator_cop1Handler(struct pt_regs *xcp, - struct mips_fpu_struct *ctx, int has_fpu); + struct mips_fpu_struct *ctx, int has_fpu, + void *__user *fault_addr); void (*board_be_init)(void); int (*board_be_handler)(struct pt_regs *regs, int is_fixup); @@ -661,12 +662,36 @@ asmlinkage void do_ov(struct pt_regs *regs) force_sig_info(SIGFPE, &info, current); } +static int process_fpemu_return(int sig, void __user *fault_addr) +{ + if (sig == SIGSEGV || sig == SIGBUS) { + struct siginfo si = {0}; + si.si_addr = fault_addr; + si.si_signo = sig; + if (sig == SIGSEGV) { + if (find_vma(current->mm, (unsigned long)fault_addr)) + si.si_code = SEGV_ACCERR; + else + si.si_code = SEGV_MAPERR; + } else { + si.si_code = BUS_ADRERR; + } + force_sig_info(sig, &si, current); + return 1; + } else if (sig) { + force_sig(sig, current); + return 1; + } else { + return 0; + } +} + /* * XXX Delayed fp exceptions when doing a lazy ctx switch XXX */ asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31) { - siginfo_t info; + siginfo_t info = {0}; if (notify_die(DIE_FP, "FP exception", regs, 0, regs_to_trapnr(regs), SIGFPE) == NOTIFY_STOP) @@ -675,6 +700,7 @@ asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31) if (fcr31 & FPU_CSR_UNI_X) { int sig; + void __user *fault_addr = NULL; /* * Unimplemented operation exception. If we've got the full @@ -690,7 +716,8 @@ asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31) lose_fpu(1); /* Run the emulator */ - sig = fpu_emulator_cop1Handler(regs, ¤t->thread.fpu, 1); + sig = fpu_emulator_cop1Handler(regs, ¤t->thread.fpu, 1, + &fault_addr); /* * We can't allow the emulated instruction to leave any of @@ -702,8 +729,7 @@ asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31) own_fpu(1); /* Using the FPU again. */ /* If something went wrong, signal */ - if (sig) - force_sig(sig, current); + process_fpemu_return(sig, fault_addr); return; } else if (fcr31 & FPU_CSR_INV_X) @@ -996,11 +1022,11 @@ asmlinkage void do_cpu(struct pt_regs *regs) if (!raw_cpu_has_fpu) { int sig; + void __user *fault_addr = NULL; sig = fpu_emulator_cop1Handler(regs, - ¤t->thread.fpu, 0); - if (sig) - force_sig(sig, current); - else + ¤t->thread.fpu, + 0, &fault_addr); + if (!process_fpemu_return(sig, fault_addr)) mt_ase_fp_affinity(); } diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index 3eb3cde2f66..6a1fdfef8fd 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -1092,6 +1092,10 @@ static int vpe_open(struct inode *inode, struct file *filp) /* this of-course trashes what was there before... */ v->pbuffer = vmalloc(P_SIZE); + if (!v->pbuffer) { + pr_warning("VPE loader: unable to allocate memory\n"); + return -ENOMEM; + } v->plen = P_SIZE; v->load_addr = NULL; v->len = 0; @@ -1149,10 +1153,9 @@ static int vpe_release(struct inode *inode, struct file *filp) if (ret < 0) v->shared_ptr = NULL; - // cleanup any temp buffers - if (v->pbuffer) - vfree(v->pbuffer); + vfree(v->pbuffer); v->plen = 0; + return ret; } @@ -1169,11 +1172,6 @@ static ssize_t vpe_write(struct file *file, const char __user * buffer, if (v == NULL) return -ENODEV; - if (v->pbuffer == NULL) { - printk(KERN_ERR "VPE loader: no buffer for program\n"); - return -ENOMEM; - } - if ((count + v->len) > v->plen) { printk(KERN_WARNING "VPE loader: elf size too big. Perhaps strip uneeded symbols\n"); diff --git a/arch/mips/lib/memset.S b/arch/mips/lib/memset.S index 77dc3b20110..606c8a9efe3 100644 --- a/arch/mips/lib/memset.S +++ b/arch/mips/lib/memset.S @@ -161,16 +161,16 @@ FEXPORT(__bzero) .Lfwd_fixup: PTR_L t0, TI_TASK($28) - LONG_L t0, THREAD_BUADDR(t0) andi a2, 0x3f + LONG_L t0, THREAD_BUADDR(t0) LONG_ADDU a2, t1 jr ra LONG_SUBU a2, t0 .Lpartial_fixup: PTR_L t0, TI_TASK($28) - LONG_L t0, THREAD_BUADDR(t0) andi a2, LONGMASK + LONG_L t0, THREAD_BUADDR(t0) LONG_ADDU a2, t1 jr ra LONG_SUBU a2, t0 diff --git a/arch/mips/loongson/common/env.c b/arch/mips/loongson/common/env.c index ae4cff97a56..11b193f848f 100644 --- a/arch/mips/loongson/common/env.c +++ b/arch/mips/loongson/common/env.c @@ -29,9 +29,9 @@ unsigned long memsize, highmemsize; #define parse_even_earlier(res, option, p) \ do { \ + int ret; \ if (strncmp(option, (char *)p, strlen(option)) == 0) \ - strict_strtol((char *)p + strlen(option"="), \ - 10, &res); \ + ret = strict_strtol((char *)p + strlen(option"="), 10, &res); \ } while (0) void __init prom_init_env(void) diff --git a/arch/mips/math-emu/cp1emu.c b/arch/mips/math-emu/cp1emu.c index b2ad1b0910f..d32cb050311 100644 --- a/arch/mips/math-emu/cp1emu.c +++ b/arch/mips/math-emu/cp1emu.c @@ -64,7 +64,7 @@ static int fpu_emu(struct pt_regs *, struct mips_fpu_struct *, #if __mips >= 4 && __mips != 32 static int fpux_emu(struct pt_regs *, - struct mips_fpu_struct *, mips_instruction); + struct mips_fpu_struct *, mips_instruction, void *__user *); #endif /* Further private data for which no space exists in mips_fpu_struct */ @@ -208,16 +208,23 @@ static inline int cop1_64bit(struct pt_regs *xcp) * Two instructions if the instruction is in a branch delay slot. */ -static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) +static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx, + void *__user *fault_addr) { mips_instruction ir; unsigned long emulpc, contpc; unsigned int cond; - if (get_user(ir, (mips_instruction __user *) xcp->cp0_epc)) { + if (!access_ok(VERIFY_READ, xcp->cp0_epc, sizeof(mips_instruction))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)xcp->cp0_epc; return SIGBUS; } + if (__get_user(ir, (mips_instruction __user *) xcp->cp0_epc)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)xcp->cp0_epc; + return SIGSEGV; + } /* XXX NEC Vr54xx bug workaround */ if ((xcp->cp0_cause & CAUSEF_BD) && !isBranchInstr(&ir)) @@ -245,10 +252,16 @@ static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) #endif return SIGILL; } - if (get_user(ir, (mips_instruction __user *) emulpc)) { + if (!access_ok(VERIFY_READ, emulpc, sizeof(mips_instruction))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)emulpc; return SIGBUS; } + if (__get_user(ir, (mips_instruction __user *) emulpc)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)emulpc; + return SIGSEGV; + } /* __compute_return_epc() will have updated cp0_epc */ contpc = xcp->cp0_epc; /* In order not to confuse ptrace() et al, tweak context */ @@ -269,10 +282,17 @@ static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) u64 val; MIPS_FPU_EMU_INC_STATS(loads); - if (get_user(val, va)) { + + if (!access_ok(VERIFY_READ, va, sizeof(u64))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (__get_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } DITOREG(val, MIPSInst_RT(ir)); break; } @@ -284,10 +304,16 @@ static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) MIPS_FPU_EMU_INC_STATS(stores); DIFROMREG(val, MIPSInst_RT(ir)); - if (put_user(val, va)) { + if (!access_ok(VERIFY_WRITE, va, sizeof(u64))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (__put_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } break; } @@ -297,10 +323,16 @@ static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) u32 val; MIPS_FPU_EMU_INC_STATS(loads); - if (get_user(val, va)) { + if (!access_ok(VERIFY_READ, va, sizeof(u32))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (__get_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } SITOREG(val, MIPSInst_RT(ir)); break; } @@ -312,10 +344,16 @@ static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) MIPS_FPU_EMU_INC_STATS(stores); SIFROMREG(val, MIPSInst_RT(ir)); - if (put_user(val, va)) { + if (!access_ok(VERIFY_WRITE, va, sizeof(u32))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (__put_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } break; } @@ -440,11 +478,18 @@ static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) contpc = (xcp->cp0_epc + (MIPSInst_SIMM(ir) << 2)); - if (get_user(ir, - (mips_instruction __user *) xcp->cp0_epc)) { + if (!access_ok(VERIFY_READ, xcp->cp0_epc, + sizeof(mips_instruction))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)xcp->cp0_epc; return SIGBUS; } + if (__get_user(ir, + (mips_instruction __user *) xcp->cp0_epc)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)xcp->cp0_epc; + return SIGSEGV; + } switch (MIPSInst_OPCODE(ir)) { case lwc1_op: @@ -506,9 +551,8 @@ static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx) #if __mips >= 4 && __mips != 32 case cop1x_op:{ - int sig; - - if ((sig = fpux_emu(xcp, ctx, ir))) + int sig = fpux_emu(xcp, ctx, ir, fault_addr); + if (sig) return sig; break; } @@ -604,7 +648,7 @@ DEF3OP(nmadd, dp, ieee754dp_mul, ieee754dp_add, ieee754dp_neg); DEF3OP(nmsub, dp, ieee754dp_mul, ieee754dp_sub, ieee754dp_neg); static int fpux_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx, - mips_instruction ir) + mips_instruction ir, void *__user *fault_addr) { unsigned rcsr = 0; /* resulting csr */ @@ -624,10 +668,16 @@ static int fpux_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx, xcp->regs[MIPSInst_FT(ir)]); MIPS_FPU_EMU_INC_STATS(loads); - if (get_user(val, va)) { + if (!access_ok(VERIFY_READ, va, sizeof(u32))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (__get_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } SITOREG(val, MIPSInst_FD(ir)); break; @@ -638,10 +688,16 @@ static int fpux_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx, MIPS_FPU_EMU_INC_STATS(stores); SIFROMREG(val, MIPSInst_FS(ir)); - if (put_user(val, va)) { + if (!access_ok(VERIFY_WRITE, va, sizeof(u32))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (put_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } break; case madd_s_op: @@ -701,10 +757,16 @@ static int fpux_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx, xcp->regs[MIPSInst_FT(ir)]); MIPS_FPU_EMU_INC_STATS(loads); - if (get_user(val, va)) { + if (!access_ok(VERIFY_READ, va, sizeof(u64))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (__get_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } DITOREG(val, MIPSInst_FD(ir)); break; @@ -714,10 +776,16 @@ static int fpux_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx, MIPS_FPU_EMU_INC_STATS(stores); DIFROMREG(val, MIPSInst_FS(ir)); - if (put_user(val, va)) { + if (!access_ok(VERIFY_WRITE, va, sizeof(u64))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; return SIGBUS; } + if (__put_user(val, va)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = va; + return SIGSEGV; + } break; case madd_d_op: @@ -1242,7 +1310,7 @@ static int fpu_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx, } int fpu_emulator_cop1Handler(struct pt_regs *xcp, struct mips_fpu_struct *ctx, - int has_fpu) + int has_fpu, void *__user *fault_addr) { unsigned long oldepc, prevepc; mips_instruction insn; @@ -1252,10 +1320,16 @@ int fpu_emulator_cop1Handler(struct pt_regs *xcp, struct mips_fpu_struct *ctx, do { prevepc = xcp->cp0_epc; - if (get_user(insn, (mips_instruction __user *) xcp->cp0_epc)) { + if (!access_ok(VERIFY_READ, xcp->cp0_epc, sizeof(mips_instruction))) { MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)xcp->cp0_epc; return SIGBUS; } + if (__get_user(insn, (mips_instruction __user *) xcp->cp0_epc)) { + MIPS_FPU_EMU_INC_STATS(errors); + *fault_addr = (mips_instruction __user *)xcp->cp0_epc; + return SIGSEGV; + } if (insn == 0) xcp->cp0_epc += 4; /* skip nops */ else { @@ -1267,7 +1341,7 @@ int fpu_emulator_cop1Handler(struct pt_regs *xcp, struct mips_fpu_struct *ctx, */ /* convert to ieee library modes */ ieee754_csr.rm = ieee_rm[ieee754_csr.rm]; - sig = cop1Emulate(xcp, ctx); + sig = cop1Emulate(xcp, ctx, fault_addr); /* revert to mips rounding mode */ ieee754_csr.rm = mips_rm[ieee754_csr.rm]; } diff --git a/arch/mips/mm/dma-default.c b/arch/mips/mm/dma-default.c index 4fc1a0fbe00..21ea14efb83 100644 --- a/arch/mips/mm/dma-default.c +++ b/arch/mips/mm/dma-default.c @@ -288,7 +288,7 @@ int mips_dma_supported(struct device *dev, u64 mask) return plat_dma_supported(dev, mask); } -void mips_dma_cache_sync(struct device *dev, void *vaddr, size_t size, +void dma_cache_sync(struct device *dev, void *vaddr, size_t size, enum dma_data_direction direction) { BUG_ON(direction == DMA_NONE); @@ -298,6 +298,8 @@ void mips_dma_cache_sync(struct device *dev, void *vaddr, size_t size, __dma_sync((unsigned long)vaddr, size, direction); } +EXPORT_SYMBOL(dma_cache_sync); + static struct dma_map_ops mips_default_dma_map_ops = { .alloc_coherent = mips_dma_alloc_coherent, .free_coherent = mips_dma_free_coherent, diff --git a/arch/mips/mm/sc-mips.c b/arch/mips/mm/sc-mips.c index 505fecad468..9cca8de0054 100644 --- a/arch/mips/mm/sc-mips.c +++ b/arch/mips/mm/sc-mips.c @@ -68,6 +68,9 @@ static struct bcache_ops mips_sc_ops = { */ static inline int mips_sc_is_activated(struct cpuinfo_mips *c) { + unsigned int config2 = read_c0_config2(); + unsigned int tmp; + /* Check the bypass bit (L2B) */ switch (c->cputype) { case CPU_34K: @@ -83,6 +86,7 @@ static inline int mips_sc_is_activated(struct cpuinfo_mips *c) c->scache.linesz = 2 << tmp; else return 0; + return 1; } static inline int __init mips_sc_probe(void) diff --git a/arch/mips/pmc-sierra/yosemite/py-console.c b/arch/mips/pmc-sierra/yosemite/py-console.c index b7f1d9c4a8a..434d7b1a8c6 100644 --- a/arch/mips/pmc-sierra/yosemite/py-console.c +++ b/arch/mips/pmc-sierra/yosemite/py-console.c @@ -65,11 +65,15 @@ static unsigned char readb_outer_space(unsigned long long phys) __asm__ __volatile__ ( " .set mips3 \n" + " .set push \n" + " .set noreorder \n" + " .set nomacro \n" " ld %0, %1 \n" + " .set pop \n" " lbu %0, (%0) \n" " .set mips0 \n" : "=r" (res) - : "m" (vaddr)); + : "R" (vaddr)); write_c0_status(sr); ssnop_4(); @@ -89,11 +93,15 @@ static void writeb_outer_space(unsigned long long phys, unsigned char c) __asm__ __volatile__ ( " .set mips3 \n" + " .set push \n" + " .set noreorder \n" + " .set nomacro \n" " ld %0, %1 \n" + " .set pop \n" " sb %2, (%0) \n" " .set mips0 \n" : "=&r" (tmp) - : "m" (vaddr), "r" (c)); + : "R" (vaddr), "r" (c)); write_c0_status(sr); ssnop_4(); diff --git a/arch/mips/sibyte/swarm/setup.c b/arch/mips/sibyte/swarm/setup.c index c308989fc46..41707a245de 100644 --- a/arch/mips/sibyte/swarm/setup.c +++ b/arch/mips/sibyte/swarm/setup.c @@ -82,7 +82,7 @@ int swarm_be_handler(struct pt_regs *regs, int is_fixup) enum swarm_rtc_type { RTC_NONE, RTC_XICOR, - RTC_M4LT81 + RTC_M41T81, }; enum swarm_rtc_type swarm_rtc_type; @@ -96,7 +96,7 @@ void read_persistent_clock(struct timespec *ts) sec = xicor_get_time(); break; - case RTC_M4LT81: + case RTC_M41T81: sec = m41t81_get_time(); break; @@ -115,7 +115,7 @@ int rtc_mips_set_time(unsigned long sec) case RTC_XICOR: return xicor_set_time(sec); - case RTC_M4LT81: + case RTC_M41T81: return m41t81_set_time(sec); case RTC_NONE: @@ -141,7 +141,7 @@ void __init plat_mem_setup(void) if (xicor_probe()) swarm_rtc_type = RTC_XICOR; if (m41t81_probe()) - swarm_rtc_type = RTC_M4LT81; + swarm_rtc_type = RTC_M41T81; #ifdef CONFIG_VT screen_info = (struct screen_info) { diff --git a/arch/mn10300/kernel/time.c b/arch/mn10300/kernel/time.c index f860a340acc..75da468090b 100644 --- a/arch/mn10300/kernel/time.c +++ b/arch/mn10300/kernel/time.c @@ -40,21 +40,17 @@ unsigned long long sched_clock(void) unsigned long long ll; unsigned l[2]; } tsc64, result; - unsigned long tsc, tmp; + unsigned long tmp; unsigned product[3]; /* 96-bit intermediate value */ /* cnt32_to_63() is not safe with preemption */ preempt_disable(); - /* read the TSC value - */ - tsc = get_cycles(); - - /* expand to 64-bits. + /* expand the tsc to 64-bits. * - sched_clock() must be called once a minute or better or the * following will go horribly wrong - see cnt32_to_63() */ - tsc64.ll = cnt32_to_63(tsc) & 0x7fffffffffffffffULL; + tsc64.ll = cnt32_to_63(get_cycles()) & 0x7fffffffffffffffULL; preempt_enable(); diff --git a/arch/tile/include/asm/signal.h b/arch/tile/include/asm/signal.h index c1ee1d61d44..81d92a45cd4 100644 --- a/arch/tile/include/asm/signal.h +++ b/arch/tile/include/asm/signal.h @@ -25,7 +25,7 @@ #if defined(__KERNEL__) && !defined(__ASSEMBLY__) struct pt_regs; -int restore_sigcontext(struct pt_regs *, struct sigcontext __user *, long *); +int restore_sigcontext(struct pt_regs *, struct sigcontext __user *); int setup_sigcontext(struct sigcontext __user *, struct pt_regs *); void do_signal(struct pt_regs *regs); #endif diff --git a/arch/tile/kernel/compat_signal.c b/arch/tile/kernel/compat_signal.c index 543d6a33aa2..dbb0dfc7bec 100644 --- a/arch/tile/kernel/compat_signal.c +++ b/arch/tile/kernel/compat_signal.c @@ -290,12 +290,12 @@ long compat_sys_sigaltstack(const struct compat_sigaltstack __user *uss_ptr, return ret; } +/* The assembly shim for this function arranges to ignore the return value. */ long compat_sys_rt_sigreturn(struct pt_regs *regs) { struct compat_rt_sigframe __user *frame = (struct compat_rt_sigframe __user *) compat_ptr(regs->sp); sigset_t set; - long r0; if (!access_ok(VERIFY_READ, frame, sizeof(*frame))) goto badframe; @@ -308,13 +308,13 @@ long compat_sys_rt_sigreturn(struct pt_regs *regs) recalc_sigpending(); spin_unlock_irq(¤t->sighand->siglock); - if (restore_sigcontext(regs, &frame->uc.uc_mcontext, &r0)) + if (restore_sigcontext(regs, &frame->uc.uc_mcontext)) goto badframe; if (compat_sys_sigaltstack(&frame->uc.uc_stack, NULL, regs) != 0) goto badframe; - return r0; + return 0; badframe: force_sig(SIGSEGV, current); diff --git a/arch/tile/kernel/intvec_32.S b/arch/tile/kernel/intvec_32.S index f5821626247..5eed4a02bf6 100644 --- a/arch/tile/kernel/intvec_32.S +++ b/arch/tile/kernel/intvec_32.S @@ -1342,8 +1342,8 @@ handle_syscall: lw r20, r20 /* Jump to syscall handler. */ - jalr r20; .Lhandle_syscall_link: - FEEDBACK_REENTER(handle_syscall) + jalr r20 +.Lhandle_syscall_link: /* value of "lr" after "jalr r20" above */ /* * Write our r0 onto the stack so it gets restored instead @@ -1352,6 +1352,9 @@ handle_syscall: PTREGS_PTR(r29, PTREGS_OFFSET_REG(0)) sw r29, r0 +.Lsyscall_sigreturn_skip: + FEEDBACK_REENTER(handle_syscall) + /* Do syscall trace again, if requested. */ lw r30, r31 andi r30, r30, _TIF_SYSCALL_TRACE @@ -1536,9 +1539,24 @@ STD_ENTRY_LOCAL(bad_intr) }; \ STD_ENDPROC(_##x) +/* + * Special-case sigreturn to not write r0 to the stack on return. + * This is technically more efficient, but it also avoids difficulties + * in the 64-bit OS when handling 32-bit compat code, since we must not + * sign-extend r0 for the sigreturn return-value case. + */ +#define PTREGS_SYSCALL_SIGRETURN(x, reg) \ + STD_ENTRY(_##x); \ + addli lr, lr, .Lsyscall_sigreturn_skip - .Lhandle_syscall_link; \ + { \ + PTREGS_PTR(reg, PTREGS_OFFSET_BASE); \ + j x \ + }; \ + STD_ENDPROC(_##x) + PTREGS_SYSCALL(sys_execve, r3) PTREGS_SYSCALL(sys_sigaltstack, r2) -PTREGS_SYSCALL(sys_rt_sigreturn, r0) +PTREGS_SYSCALL_SIGRETURN(sys_rt_sigreturn, r0) PTREGS_SYSCALL(sys_cmpxchg_badaddr, r1) /* Save additional callee-saves to pt_regs, put address in r4 and jump. */ diff --git a/arch/tile/kernel/process.c b/arch/tile/kernel/process.c index 8430f45daea..e90eb53173b 100644 --- a/arch/tile/kernel/process.c +++ b/arch/tile/kernel/process.c @@ -212,6 +212,13 @@ int copy_thread(unsigned long clone_flags, unsigned long sp, childregs->sp = sp; /* override with new user stack pointer */ /* + * If CLONE_SETTLS is set, set "tp" in the new task to "r4", + * which is passed in as arg #5 to sys_clone(). + */ + if (clone_flags & CLONE_SETTLS) + childregs->tp = regs->regs[4]; + + /* * Copy the callee-saved registers from the passed pt_regs struct * into the context-switch callee-saved registers area. * This way when we start the interrupt-return sequence, the @@ -539,6 +546,7 @@ struct task_struct *__sched _switch_to(struct task_struct *prev, return __switch_to(prev, next, next_current_ksp0(next)); } +/* Note there is an implicit fifth argument if (clone_flags & CLONE_SETTLS). */ SYSCALL_DEFINE5(clone, unsigned long, clone_flags, unsigned long, newsp, void __user *, parent_tidptr, void __user *, child_tidptr, struct pt_regs *, regs) diff --git a/arch/tile/kernel/signal.c b/arch/tile/kernel/signal.c index 757407e3669..1260321155f 100644 --- a/arch/tile/kernel/signal.c +++ b/arch/tile/kernel/signal.c @@ -52,7 +52,7 @@ SYSCALL_DEFINE3(sigaltstack, const stack_t __user *, uss, */ int restore_sigcontext(struct pt_regs *regs, - struct sigcontext __user *sc, long *pr0) + struct sigcontext __user *sc) { int err = 0; int i; @@ -75,17 +75,15 @@ int restore_sigcontext(struct pt_regs *regs, regs->faultnum = INT_SWINT_1_SIGRETURN; - err |= __get_user(*pr0, &sc->gregs[0]); return err; } -/* sigreturn() returns long since it restores r0 in the interrupted code. */ +/* The assembly shim for this function arranges to ignore the return value. */ SYSCALL_DEFINE1(rt_sigreturn, struct pt_regs *, regs) { struct rt_sigframe __user *frame = (struct rt_sigframe __user *)(regs->sp); sigset_t set; - long r0; if (!access_ok(VERIFY_READ, frame, sizeof(*frame))) goto badframe; @@ -98,13 +96,13 @@ SYSCALL_DEFINE1(rt_sigreturn, struct pt_regs *, regs) recalc_sigpending(); spin_unlock_irq(¤t->sighand->siglock); - if (restore_sigcontext(regs, &frame->uc.uc_mcontext, &r0)) + if (restore_sigcontext(regs, &frame->uc.uc_mcontext)) goto badframe; if (do_sigaltstack(&frame->uc.uc_stack, NULL, regs->sp) == -EFAULT) goto badframe; - return r0; + return 0; badframe: force_sig(SIGSEGV, current); diff --git a/arch/x86/boot/compressed/misc.c b/arch/x86/boot/compressed/misc.c index 23f315c9f21..325c05294fc 100644 --- a/arch/x86/boot/compressed/misc.c +++ b/arch/x86/boot/compressed/misc.c @@ -355,7 +355,7 @@ asmlinkage void decompress_kernel(void *rmode, memptr heap, if (heap > 0x3fffffffffffUL) error("Destination address too large"); #else - if (heap > ((-__PAGE_OFFSET-(512<<20)-1) & 0x7fffffff)) + if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff)) error("Destination address too large"); #endif #ifndef CONFIG_RELOCATABLE diff --git a/arch/x86/include/asm/e820.h b/arch/x86/include/asm/e820.h index 5be1542fbfa..e99d55d74df 100644 --- a/arch/x86/include/asm/e820.h +++ b/arch/x86/include/asm/e820.h @@ -72,6 +72,9 @@ struct e820map { #define BIOS_BEGIN 0x000a0000 #define BIOS_END 0x00100000 +#define BIOS_ROM_BASE 0xffe00000 +#define BIOS_ROM_END 0xffffffff + #ifdef __KERNEL__ /* see comment in arch/x86/kernel/e820.c */ extern struct e820map e820; diff --git a/arch/x86/include/asm/kvm_host.h b/arch/x86/include/asm/kvm_host.h index 9e6fe391094..f702f82aa1e 100644 --- a/arch/x86/include/asm/kvm_host.h +++ b/arch/x86/include/asm/kvm_host.h @@ -79,7 +79,7 @@ #define KVM_NUM_MMU_PAGES (1 << KVM_MMU_HASH_SHIFT) #define KVM_MIN_FREE_MMU_PAGES 5 #define KVM_REFILL_PAGES 25 -#define KVM_MAX_CPUID_ENTRIES 40 +#define KVM_MAX_CPUID_ENTRIES 80 #define KVM_NR_FIXED_MTRR_REGION 88 #define KVM_NR_VAR_MTRR 8 diff --git a/arch/x86/kernel/Makefile b/arch/x86/kernel/Makefile index 9e13763b609..1e994754d32 100644 --- a/arch/x86/kernel/Makefile +++ b/arch/x86/kernel/Makefile @@ -45,6 +45,7 @@ obj-y += pci-dma.o quirks.o i8237.o topology.o kdebugfs.o obj-y += alternative.o i8253.o pci-nommu.o hw_breakpoint.o obj-y += tsc.o io_delay.o rtc.o obj-y += pci-iommu_table.o +obj-y += resource.o obj-$(CONFIG_X86_TRAMPOLINE) += trampoline.o obj-y += process.o diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c index 3f838d53739..78218135b48 100644 --- a/arch/x86/kernel/apic/apic.c +++ b/arch/x86/kernel/apic/apic.c @@ -1389,6 +1389,14 @@ void __cpuinit end_local_APIC_setup(void) setup_apic_nmi_watchdog(NULL); apic_pm_activate(); + + /* + * Now that local APIC setup is completed for BP, configure the fault + * handling for interrupt remapping. + */ + if (!smp_processor_id() && intr_remapping_enabled) + enable_drhd_fault_handling(); + } #ifdef CONFIG_X86_X2APIC diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c index 7cc0a721f62..fadcd743a74 100644 --- a/arch/x86/kernel/apic/io_apic.c +++ b/arch/x86/kernel/apic/io_apic.c @@ -2430,13 +2430,12 @@ static void ack_apic_level(struct irq_data *data) { struct irq_cfg *cfg = data->chip_data; int i, do_unmask_irq = 0, irq = data->irq; - struct irq_desc *desc = irq_to_desc(irq); unsigned long v; irq_complete_move(cfg); #ifdef CONFIG_GENERIC_PENDING_IRQ /* If we are moving the irq we need to mask it */ - if (unlikely(desc->status & IRQ_MOVE_PENDING)) { + if (unlikely(irq_to_desc(irq)->status & IRQ_MOVE_PENDING)) { do_unmask_irq = 1; mask_ioapic(cfg); } @@ -3413,6 +3412,7 @@ dmar_msi_set_affinity(struct irq_data *data, const struct cpumask *mask, msg.data |= MSI_DATA_VECTOR(cfg->vector); msg.address_lo &= ~MSI_ADDR_DEST_ID_MASK; msg.address_lo |= MSI_ADDR_DEST_ID(dest); + msg.address_hi = MSI_ADDR_BASE_HI | MSI_ADDR_EXT_DEST_ID(dest); dmar_msi_write(irq, &msg); diff --git a/arch/x86/kernel/apic/probe_64.c b/arch/x86/kernel/apic/probe_64.c index f9e4e6a5407..d8c4a6feb28 100644 --- a/arch/x86/kernel/apic/probe_64.c +++ b/arch/x86/kernel/apic/probe_64.c @@ -79,13 +79,6 @@ void __init default_setup_apic_routing(void) /* need to update phys_pkg_id */ apic->phys_pkg_id = apicid_phys_pkg_id; } - - /* - * Now that apic routing model is selected, configure the - * fault handling for intr remapping. - */ - if (intr_remapping_enabled) - enable_drhd_fault_handling(); } /* Same for both flat and physical. */ diff --git a/arch/x86/kernel/head_32.S b/arch/x86/kernel/head_32.S index bcece91dd31..c0dbd9ac24f 100644 --- a/arch/x86/kernel/head_32.S +++ b/arch/x86/kernel/head_32.S @@ -60,16 +60,18 @@ #define PAGE_TABLE_SIZE(pages) ((pages) / PTRS_PER_PGD) #endif +/* Number of possible pages in the lowmem region */ +LOWMEM_PAGES = (((1<<32) - __PAGE_OFFSET) >> PAGE_SHIFT) + /* Enough space to fit pagetables for the low memory linear map */ -MAPPING_BEYOND_END = \ - PAGE_TABLE_SIZE(((1<<32) - __PAGE_OFFSET) >> PAGE_SHIFT) << PAGE_SHIFT +MAPPING_BEYOND_END = PAGE_TABLE_SIZE(LOWMEM_PAGES) << PAGE_SHIFT /* * Worst-case size of the kernel mapping we need to make: - * the worst-case size of the kernel itself, plus the extra we need - * to map for the linear map. + * a relocatable kernel can live anywhere in lowmem, so we need to be able + * to map all of lowmem. */ -KERNEL_PAGES = (KERNEL_IMAGE_SIZE + MAPPING_BEYOND_END)>>PAGE_SHIFT +KERNEL_PAGES = LOWMEM_PAGES INIT_MAP_SIZE = PAGE_TABLE_SIZE(KERNEL_PAGES) * PAGE_SIZE_asm RESERVE_BRK(pagetables, INIT_MAP_SIZE) @@ -620,13 +622,13 @@ ENTRY(initial_code) __PAGE_ALIGNED_BSS .align PAGE_SIZE_asm #ifdef CONFIG_X86_PAE -initial_pg_pmd: +ENTRY(initial_pg_pmd) .fill 1024*KPMDS,4,0 #else ENTRY(initial_page_table) .fill 1024,4,0 #endif -initial_pg_fixmap: +ENTRY(initial_pg_fixmap) .fill 1024,4,0 ENTRY(empty_zero_page) .fill 4096,1,0 diff --git a/arch/x86/kernel/hpet.c b/arch/x86/kernel/hpet.c index ae03cab4352..4ff5968f12d 100644 --- a/arch/x86/kernel/hpet.c +++ b/arch/x86/kernel/hpet.c @@ -27,6 +27,9 @@ #define HPET_DEV_FSB_CAP 0x1000 #define HPET_DEV_PERI_CAP 0x2000 +#define HPET_MIN_CYCLES 128 +#define HPET_MIN_PROG_DELTA (HPET_MIN_CYCLES + (HPET_MIN_CYCLES >> 1)) + #define EVT_TO_HPET_DEV(evt) container_of(evt, struct hpet_dev, evt) /* @@ -299,8 +302,9 @@ static void hpet_legacy_clockevent_register(void) /* Calculate the min / max delta */ hpet_clockevent.max_delta_ns = clockevent_delta2ns(0x7FFFFFFF, &hpet_clockevent); - /* 5 usec minimum reprogramming delta. */ - hpet_clockevent.min_delta_ns = 5000; + /* Setup minimum reprogramming delta. */ + hpet_clockevent.min_delta_ns = clockevent_delta2ns(HPET_MIN_PROG_DELTA, + &hpet_clockevent); /* * Start hpet with the boot cpu mask and make it @@ -393,22 +397,24 @@ static int hpet_next_event(unsigned long delta, * the wraparound into account) nor a simple count down event * mode. Further the write to the comparator register is * delayed internally up to two HPET clock cycles in certain - * chipsets (ATI, ICH9,10). We worked around that by reading - * back the compare register, but that required another - * workaround for ICH9,10 chips where the first readout after - * write can return the old stale value. We already have a - * minimum delta of 5us enforced, but a NMI or SMI hitting + * chipsets (ATI, ICH9,10). Some newer AMD chipsets have even + * longer delays. We worked around that by reading back the + * compare register, but that required another workaround for + * ICH9,10 chips where the first readout after write can + * return the old stale value. We already had a minimum + * programming delta of 5us enforced, but a NMI or SMI hitting * between the counter readout and the comparator write can * move us behind that point easily. Now instead of reading * the compare register back several times, we make the ETIME * decision based on the following: Return ETIME if the - * counter value after the write is less than 8 HPET cycles + * counter value after the write is less than HPET_MIN_CYCLES * away from the event or if the counter is already ahead of - * the event. + * the event. The minimum programming delta for the generic + * clockevents code is set to 1.5 * HPET_MIN_CYCLES. */ res = (s32)(cnt - hpet_readl(HPET_COUNTER)); - return res < 8 ? -ETIME : 0; + return res < HPET_MIN_CYCLES ? -ETIME : 0; } static void hpet_legacy_set_mode(enum clock_event_mode mode, diff --git a/arch/x86/kernel/resource.c b/arch/x86/kernel/resource.c new file mode 100644 index 00000000000..2a26819bb6a --- /dev/null +++ b/arch/x86/kernel/resource.c @@ -0,0 +1,48 @@ +#include <linux/ioport.h> +#include <asm/e820.h> + +static void resource_clip(struct resource *res, resource_size_t start, + resource_size_t end) +{ + resource_size_t low = 0, high = 0; + + if (res->end < start || res->start > end) + return; /* no conflict */ + + if (res->start < start) + low = start - res->start; + + if (res->end > end) + high = res->end - end; + + /* Keep the area above or below the conflict, whichever is larger */ + if (low > high) + res->end = start - 1; + else + res->start = end + 1; +} + +static void remove_e820_regions(struct resource *avail) +{ + int i; + struct e820entry *entry; + + for (i = 0; i < e820.nr_map; i++) { + entry = &e820.map[i]; + + resource_clip(avail, entry->addr, + entry->addr + entry->size - 1); + } +} + +void arch_remove_reservations(struct resource *avail) +{ + /* Trim out BIOS areas (low 1MB and high 2MB) and E820 regions */ + if (avail->flags & IORESOURCE_MEM) { + if (avail->start < BIOS_END) + avail->start = BIOS_END; + resource_clip(avail, BIOS_ROM_BASE, BIOS_ROM_END); + + remove_e820_regions(avail); + } +} diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c index 21c6746338a..85268f8eadf 100644 --- a/arch/x86/kernel/setup.c +++ b/arch/x86/kernel/setup.c @@ -769,7 +769,6 @@ void __init setup_arch(char **cmdline_p) x86_init.oem.arch_setup(); - resource_alloc_from_bottom = 0; iomem_resource.end = (1ULL << boot_cpu_data.x86_phys_bits) - 1; setup_memory_map(); parse_setup_data(); diff --git a/arch/x86/kernel/xsave.c b/arch/x86/kernel/xsave.c index 9c253bd65e2..547128546cc 100644 --- a/arch/x86/kernel/xsave.c +++ b/arch/x86/kernel/xsave.c @@ -394,7 +394,8 @@ static void __init setup_xstate_init(void) * Setup init_xstate_buf to represent the init state of * all the features managed by the xsave */ - init_xstate_buf = alloc_bootmem(xstate_size); + init_xstate_buf = alloc_bootmem_align(xstate_size, + __alignof__(struct xsave_struct)); init_xstate_buf->i387.mxcsr = MXCSR_DEFAULT; clts(); diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c index 1ca12298ffc..b81a9b7c2ca 100644 --- a/arch/x86/kvm/svm.c +++ b/arch/x86/kvm/svm.c @@ -3494,6 +3494,10 @@ static void svm_cpuid_update(struct kvm_vcpu *vcpu) static void svm_set_supported_cpuid(u32 func, struct kvm_cpuid_entry2 *entry) { switch (func) { + case 0x00000001: + /* Mask out xsave bit as long as it is not supported by SVM */ + entry->ecx &= ~(bit(X86_FEATURE_XSAVE)); + break; case 0x80000001: if (nested) entry->ecx |= (1 << 2); /* Set SVM bit */ diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c index ff21fdda0c5..81fcbe9515c 100644 --- a/arch/x86/kvm/vmx.c +++ b/arch/x86/kvm/vmx.c @@ -4227,11 +4227,6 @@ static int vmx_get_lpage_level(void) return PT_PDPE_LEVEL; } -static inline u32 bit(int bitno) -{ - return 1 << (bitno & 31); -} - static void vmx_cpuid_update(struct kvm_vcpu *vcpu) { struct kvm_cpuid_entry2 *best; diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c index cdac9e592aa..b989e1f1e5d 100644 --- a/arch/x86/kvm/x86.c +++ b/arch/x86/kvm/x86.c @@ -155,11 +155,6 @@ struct kvm_stats_debugfs_item debugfs_entries[] = { u64 __read_mostly host_xcr0; -static inline u32 bit(int bitno) -{ - return 1 << (bitno & 31); -} - static void kvm_on_user_return(struct user_return_notifier *urn) { unsigned slot; @@ -4569,9 +4564,11 @@ static void kvm_timer_init(void) #ifdef CONFIG_CPU_FREQ struct cpufreq_policy policy; memset(&policy, 0, sizeof(policy)); - cpufreq_get_policy(&policy, get_cpu()); + cpu = get_cpu(); + cpufreq_get_policy(&policy, cpu); if (policy.cpuinfo.max_freq) max_tsc_khz = policy.cpuinfo.max_freq; + put_cpu(); #endif cpufreq_register_notifier(&kvmclock_cpufreq_notifier_block, CPUFREQ_TRANSITION_NOTIFIER); @@ -5522,6 +5519,8 @@ int kvm_arch_vcpu_ioctl_set_sregs(struct kvm_vcpu *vcpu, mmu_reset_needed |= kvm_read_cr4(vcpu) != sregs->cr4; kvm_x86_ops->set_cr4(vcpu, sregs->cr4); + if (sregs->cr4 & X86_CR4_OSXSAVE) + update_cpuid(vcpu); if (!is_long_mode(vcpu) && is_pae(vcpu)) { load_pdptrs(vcpu, vcpu->arch.walk_mmu, vcpu->arch.cr3); mmu_reset_needed = 1; diff --git a/arch/x86/kvm/x86.h b/arch/x86/kvm/x86.h index 2cea414489f..c600da830ce 100644 --- a/arch/x86/kvm/x86.h +++ b/arch/x86/kvm/x86.h @@ -70,6 +70,11 @@ static inline int is_paging(struct kvm_vcpu *vcpu) return kvm_read_cr0_bits(vcpu, X86_CR0_PG); } +static inline u32 bit(int bitno) +{ + return 1 << (bitno & 31); +} + void kvm_before_handle_nmi(struct kvm_vcpu *vcpu); void kvm_after_handle_nmi(struct kvm_vcpu *vcpu); int kvm_inject_realmode_interrupt(struct kvm_vcpu *vcpu, int irq); diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c index 73b1e1a1f48..4996cf5f73a 100644 --- a/arch/x86/lguest/boot.c +++ b/arch/x86/lguest/boot.c @@ -531,7 +531,10 @@ static void lguest_write_cr3(unsigned long cr3) { lguest_data.pgdir = cr3; lazy_hcall1(LHCALL_NEW_PGTABLE, cr3); - cr3_changed = true; + + /* These two page tables are simple, linear, and used during boot */ + if (cr3 != __pa(swapper_pg_dir) && cr3 != __pa(initial_page_table)) + cr3_changed = true; } static unsigned long lguest_read_cr3(void) @@ -703,9 +706,9 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) * to forget all of them. Fortunately, this is very rare. * * ... except in early boot when the kernel sets up the initial pagetables, - * which makes booting astonishingly slow: 1.83 seconds! So we don't even tell - * the Host anything changed until we've done the first page table switch, - * which brings boot back to 0.25 seconds. + * which makes booting astonishingly slow: 48 seconds! So we don't even tell + * the Host anything changed until we've done the first real page table switch, + * which brings boot back to 4.3 seconds. */ static void lguest_set_pte(pte_t *ptep, pte_t pteval) { @@ -1002,7 +1005,7 @@ static void lguest_time_init(void) clockevents_register_device(&lguest_clockevent); /* Finally, we unblock the timer interrupt. */ - enable_lguest_irq(0); + clear_bit(0, lguest_data.blocked_interrupts); } /* @@ -1349,9 +1352,6 @@ __init void lguest_init(void) */ switch_to_new_gdt(0); - /* We actually boot with all memory mapped, but let's say 128MB. */ - max_pfn_mapped = (128*1024*1024) >> PAGE_SHIFT; - /* * The Host<->Guest Switcher lives at the top of our address space, and * the Host told us how big it is when we made LGUEST_INIT hypercall: diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S index 4f420c2f2d5..e7d5382ef26 100644 --- a/arch/x86/lguest/i386_head.S +++ b/arch/x86/lguest/i386_head.S @@ -4,6 +4,7 @@ #include <asm/asm-offsets.h> #include <asm/thread_info.h> #include <asm/processor-flags.h> +#include <asm/pgtable.h> /*G:020 * Our story starts with the kernel booting into startup_32 in @@ -37,9 +38,113 @@ ENTRY(lguest_entry) /* Set up the initial stack so we can run C code. */ movl $(init_thread_union+THREAD_SIZE),%esp + call init_pagetables + /* Jumps are relative: we're running __PAGE_OFFSET too low. */ jmp lguest_init+__PAGE_OFFSET +/* + * Initialize page tables. This creates a PDE and a set of page + * tables, which are located immediately beyond __brk_base. The variable + * _brk_end is set up to point to the first "safe" location. + * Mappings are created both at virtual address 0 (identity mapping) + * and PAGE_OFFSET for up to _end. + * + * FIXME: This code is taken verbatim from arch/x86/kernel/head_32.S: they + * don't have a stack at this point, so we can't just use call and ret. + */ +init_pagetables: +#if PTRS_PER_PMD > 1 +#define PAGE_TABLE_SIZE(pages) (((pages) / PTRS_PER_PMD) + PTRS_PER_PGD) +#else +#define PAGE_TABLE_SIZE(pages) ((pages) / PTRS_PER_PGD) +#endif +#define pa(X) ((X) - __PAGE_OFFSET) + +/* Enough space to fit pagetables for the low memory linear map */ +MAPPING_BEYOND_END = \ + PAGE_TABLE_SIZE(((1<<32) - __PAGE_OFFSET) >> PAGE_SHIFT) << PAGE_SHIFT +#ifdef CONFIG_X86_PAE + + /* + * In PAE mode initial_page_table is statically defined to contain + * enough entries to cover the VMSPLIT option (that is the top 1, 2 or 3 + * entries). The identity mapping is handled by pointing two PGD entries + * to the first kernel PMD. + * + * Note the upper half of each PMD or PTE are always zero at this stage. + */ + +#define KPMDS (((-__PAGE_OFFSET) >> 30) & 3) /* Number of kernel PMDs */ + + xorl %ebx,%ebx /* %ebx is kept at zero */ + + movl $pa(__brk_base), %edi + movl $pa(initial_pg_pmd), %edx + movl $PTE_IDENT_ATTR, %eax +10: + leal PDE_IDENT_ATTR(%edi),%ecx /* Create PMD entry */ + movl %ecx,(%edx) /* Store PMD entry */ + /* Upper half already zero */ + addl $8,%edx + movl $512,%ecx +11: + stosl + xchgl %eax,%ebx + stosl + xchgl %eax,%ebx + addl $0x1000,%eax + loop 11b + + /* + * End condition: we must map up to the end + MAPPING_BEYOND_END. + */ + movl $pa(_end) + MAPPING_BEYOND_END + PTE_IDENT_ATTR, %ebp + cmpl %ebp,%eax + jb 10b +1: + addl $__PAGE_OFFSET, %edi + movl %edi, pa(_brk_end) + shrl $12, %eax + movl %eax, pa(max_pfn_mapped) + + /* Do early initialization of the fixmap area */ + movl $pa(initial_pg_fixmap)+PDE_IDENT_ATTR,%eax + movl %eax,pa(initial_pg_pmd+0x1000*KPMDS-8) +#else /* Not PAE */ + +page_pde_offset = (__PAGE_OFFSET >> 20); + + movl $pa(__brk_base), %edi + movl $pa(initial_page_table), %edx + movl $PTE_IDENT_ATTR, %eax +10: + leal PDE_IDENT_ATTR(%edi),%ecx /* Create PDE entry */ + movl %ecx,(%edx) /* Store identity PDE entry */ + movl %ecx,page_pde_offset(%edx) /* Store kernel PDE entry */ + addl $4,%edx + movl $1024, %ecx +11: + stosl + addl $0x1000,%eax + loop 11b + /* + * End condition: we must map up to the end + MAPPING_BEYOND_END. + */ + movl $pa(_end) + MAPPING_BEYOND_END + PTE_IDENT_ATTR, %ebp + cmpl %ebp,%eax + jb 10b + addl $__PAGE_OFFSET, %edi + movl %edi, pa(_brk_end) + shrl $12, %eax + movl %eax, pa(max_pfn_mapped) + + /* Do early initialization of the fixmap area */ + movl $pa(initial_pg_fixmap)+PDE_IDENT_ATTR,%eax + movl %eax,pa(initial_page_table+0xffc) +#endif + ret + /*G:055 * We create a macro which puts the assembler code between lgstart_ and lgend_ * markers. These templates are put in the .text section: they can't be diff --git a/arch/x86/pci/i386.c b/arch/x86/pci/i386.c index c4bb261c106..b1805b78842 100644 --- a/arch/x86/pci/i386.c +++ b/arch/x86/pci/i386.c @@ -65,21 +65,13 @@ pcibios_align_resource(void *data, const struct resource *res, resource_size_t size, resource_size_t align) { struct pci_dev *dev = data; - resource_size_t start = round_down(res->end - size + 1, align); + resource_size_t start = res->start; if (res->flags & IORESOURCE_IO) { - - /* - * If we're avoiding ISA aliases, the largest contiguous I/O - * port space is 256 bytes. Clearing bits 9 and 10 preserves - * all 256-byte and smaller alignments, so the result will - * still be correctly aligned. - */ - if (!skip_isa_ioresource_align(dev)) - start &= ~0x300; - } else if (res->flags & IORESOURCE_MEM) { - if (start < BIOS_END) - start = res->end; /* fail; no space */ + if (skip_isa_ioresource_align(dev)) + return start; + if (start & 0x300) + start = (start + 0x3ff) & ~0x3ff; } return start; } diff --git a/arch/x86/vdso/Makefile b/arch/x86/vdso/Makefile index 4a2afa1bac5..b6552b189bc 100644 --- a/arch/x86/vdso/Makefile +++ b/arch/x86/vdso/Makefile @@ -25,7 +25,7 @@ targets += vdso.so vdso.so.dbg vdso.lds $(vobjs-y) export CPPFLAGS_vdso.lds += -P -C -VDSO_LDFLAGS_vdso.lds = -m elf_x86_64 -Wl,-soname=linux-vdso.so.1 \ +VDSO_LDFLAGS_vdso.lds = -m64 -Wl,-soname=linux-vdso.so.1 \ -Wl,-z,max-page-size=4096 -Wl,-z,common-page-size=4096 $(obj)/vdso.o: $(src)/vdso.S $(obj)/vdso.so @@ -69,7 +69,7 @@ vdso32.so-$(VDSO32-y) += sysenter vdso32-images = $(vdso32.so-y:%=vdso32-%.so) CPPFLAGS_vdso32.lds = $(CPPFLAGS_vdso.lds) -VDSO_LDFLAGS_vdso32.lds = -m elf_i386 -Wl,-soname=linux-gate.so.1 +VDSO_LDFLAGS_vdso32.lds = -m32 -Wl,-soname=linux-gate.so.1 # This makes sure the $(obj) subdirectory exists even though vdso32/ # is not a kbuild sub-make subdirectory. |