diff options
Diffstat (limited to 'drivers/ata/libata-core.c')
| -rw-r--r-- | drivers/ata/libata-core.c | 25 |
1 files changed, 15 insertions, 10 deletions
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index ca4d208ddf3..045a486a09e 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -125,19 +125,19 @@ MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link spe static int atapi_enabled = 1; module_param(atapi_enabled, int, 0444); -MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on)"); +MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on [default])"); static int atapi_dmadir = 0; module_param(atapi_dmadir, int, 0444); -MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off, 1=on)"); +MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off [default], 1=on)"); int atapi_passthru16 = 1; module_param(atapi_passthru16, int, 0444); -MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices; on by default (0=off, 1=on)"); +MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices (0=off, 1=on [default])"); int libata_fua = 0; module_param_named(fua, libata_fua, int, 0444); -MODULE_PARM_DESC(fua, "FUA support (0=off, 1=on)"); +MODULE_PARM_DESC(fua, "FUA support (0=off [default], 1=on)"); static int ata_ignore_hpa; module_param_named(ignore_hpa, ata_ignore_hpa, int, 0644); @@ -153,11 +153,11 @@ MODULE_PARM_DESC(ata_probe_timeout, "Set ATA probing timeout (seconds)"); int libata_noacpi = 0; module_param_named(noacpi, libata_noacpi, int, 0444); -MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in probe/suspend/resume when set"); +MODULE_PARM_DESC(noacpi, "Disable the use of ACPI in probe/suspend/resume (0=off [default], 1=on)"); int libata_allow_tpm = 0; module_param_named(allow_tpm, libata_allow_tpm, int, 0444); -MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands"); +MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands (0=off [default], 1=on)"); MODULE_AUTHOR("Jeff Garzik"); MODULE_DESCRIPTION("Library module for ATA devices"); @@ -1993,11 +1993,17 @@ unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd) * Check if the current speed of the device requires IORDY. Used * by various controllers for chip configuration. */ - unsigned int ata_pio_need_iordy(const struct ata_device *adev) { - /* Controller doesn't support IORDY. Probably a pointless check - as the caller should know this */ + /* Don't set IORDY if we're preparing for reset. IORDY may + * lead to controller lock up on certain controllers if the + * port is not occupied. See bko#11703 for details. + */ + if (adev->link->ap->pflags & ATA_PFLAG_RESETTING) + return 0; + /* Controller doesn't support IORDY. Probably a pointless + * check as the caller should know this. + */ if (adev->link->ap->flags & ATA_FLAG_NO_IORDY) return 0; /* CF spec. r4.1 Table 22 says no iordy on PIO5 and PIO6. */ @@ -2020,7 +2026,6 @@ unsigned int ata_pio_need_iordy(const struct ata_device *adev) * Compute the highest mode possible if we are not using iordy. Return * -1 if no iordy mode is available. */ - static u32 ata_pio_mask_no_iordy(const struct ata_device *adev) { /* If we have no drive specific rule, then PIO 2 is non IORDY */ |