diff options
Diffstat (limited to 'drivers/ata/pata_artop.c')
| -rw-r--r-- | drivers/ata/pata_artop.c | 518 |
1 files changed, 518 insertions, 0 deletions
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c new file mode 100644 index 00000000000..d6ef3bf1bac --- /dev/null +++ b/drivers/ata/pata_artop.c @@ -0,0 +1,518 @@ +/* + * pata_artop.c - ARTOP ATA controller driver + * + * (C) 2006 Red Hat <alan@redhat.com> + * + * Based in part on drivers/ide/pci/aec62xx.c + * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org> + * 865/865R fixes for Macintosh card version from a patch to the old + * driver by Thibaut VARENE <varenet@parisc-linux.org> + * When setting the PCI latency we must set 0x80 or higher for burst + * performance Alessandro Zummo <alessandro.zummo@towertech.it> + * + * TODO + * 850 serialization once the core supports it + * Investigate no_dsc on 850R + * Clock detect + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_artop" +#define DRV_VERSION "0.4.1" + +/* + * The ARTOP has 33 Mhz and "over clocked" timing tables. Until we + * get PCI bus speed functionality we leave this as 0. Its a variable + * for when we get the functionality and also for folks wanting to + * test stuff. + */ + +static int clock = 0; + +static int artop6210_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + const struct pci_bits artop_enable_bits[] = { + { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) { + ata_port_disable(ap); + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * artop6210_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, artop6210_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * artop6260_pre_reset - check for 40/80 pin + * @ap: Port + * + * The ARTOP hardware reports the cable detect bits in register 0x49. + * Nothing complicated needed here. + */ + +static int artop6260_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits artop_enable_bits[] = { + { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 tmp; + + /* Odd numbered device ids are the units with enable bits (the -R cards) */ + if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) { + ata_port_disable(ap); + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + pci_read_config_byte(pdev, 0x49, &tmp); + if (tmp & (1 >> ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +/** + * artop6260_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, artop6260_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * artop6210_load_piomode - Load a set of PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device + * @pio: PIO mode + * + * Set PIO mode for device, in host controller PCI config space. This + * is used both to set PIO timings in PIO mode and also to set the + * matching PIO clocking for UDMA, as well as the MWDMA timings. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + const u16 timing[2][5] = { + { 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 }, + { 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 } + + }; + /* Load the PIO timing active/recovery bits */ + pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]); +} + +/** + * artop6210_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * + * Set PIO mode for device, in host controller PCI config space. For + * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In + * the event UDMA is used the later call to set_dmamode will set the + * bits as required. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + u8 ultra; + + artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); + + /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ + pci_read_config_byte(pdev, 0x54, &ultra); + ultra &= ~(3 << (2 * dn)); + pci_write_config_byte(pdev, 0x54, ultra); +} + +/** + * artop6260_load_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * @pio: PIO mode + * + * Set PIO mode for device, in host controller PCI config space. The + * ARTOP6260 and relatives store the timing data differently. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + const u8 timing[2][5] = { + { 0x00, 0x0A, 0x08, 0x33, 0x31 }, + { 0x70, 0x7A, 0x78, 0x43, 0x41 } + + }; + /* Load the PIO timing active/recovery bits */ + pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]); +} + +/** + * artop6260_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * + * Set PIO mode for device, in host controller PCI config space. For + * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In + * the event UDMA is used the later call to set_dmamode will set the + * bits as required. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ultra; + + artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); + + /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ + pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); + ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ + pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); +} + +/** + * artop6210_set_dmamode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set DMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + u8 ultra; + + if (adev->dma_mode == XFER_MW_DMA_0) + pio = 1; + else + pio = 4; + + /* Load the PIO timing active/recovery bits */ + artop6210_load_piomode(ap, adev, pio); + + pci_read_config_byte(pdev, 0x54, &ultra); + ultra &= ~(3 << (2 * dn)); + + /* Add ultra DMA bits if in UDMA mode */ + if (adev->dma_mode >= XFER_UDMA_0) { + u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock; + if (mode == 0) + mode = 1; + ultra |= (mode << (2 * dn)); + } + pci_write_config_byte(pdev, 0x54, ultra); +} + +/** + * artop6260_set_dmamode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * + * Set DMA mode for device, in host controller PCI config space. The + * ARTOP6260 and relatives store the timing data differently. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ultra; + + if (adev->dma_mode == XFER_MW_DMA_0) + pio = 1; + else + pio = 4; + + /* Load the PIO timing active/recovery bits */ + artop6260_load_piomode(ap, adev, pio); + + /* Add ultra DMA bits if in UDMA mode */ + pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); + ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ + if (adev->dma_mode >= XFER_UDMA_0) { + u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock; + if (mode == 0) + mode = 1; + ultra |= (mode << (4 * adev->devno)); + } + pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); +} + +static struct scsi_host_template artop_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations artop6210_ops = { + .port_disable = ata_port_disable, + .set_piomode = artop6210_set_piomode, + .set_dmamode = artop6210_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = artop6210_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations artop6260_ops = { + .port_disable = ata_port_disable, + .set_piomode = artop6260_set_piomode, + .set_dmamode = artop6260_set_dmamode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = artop6260_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + + +/** + * artop_init_one - Register ARTOP ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in artop_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id) +{ + static int printed_version; + static struct ata_port_info info_6210 = { + .sht = &artop_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA2, + .port_ops = &artop6210_ops, + }; + static struct ata_port_info info_626x = { + .sht = &artop_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA4, + .port_ops = &artop6260_ops, + }; + static struct ata_port_info info_626x_fast = { + .sht = &artop_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA5, + .port_ops = &artop6260_ops, + }; + struct ata_port_info *port_info[2]; + struct ata_port_info *info; + int ports = 2; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + if (id->driver_data == 0) { /* 6210 variant */ + info = &info_6210; + /* BIOS may have left us in UDMA, clear it before libata probe */ + pci_write_config_byte(pdev, 0x54, 0); + /* For the moment (also lacks dsc) */ + printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n"); + printk(KERN_WARNING "Secondary ATA ports will not be activated.\n"); + ports = 1; + } + else if (id->driver_data == 1) /* 6260 */ + info = &info_626x; + else if (id->driver_data == 2) { /* 6260 or 6260 + fast */ + unsigned long io = pci_resource_start(pdev, 4); + u8 reg; + + info = &info_626x; + if (inb(io) & 0x10) + info = &info_626x_fast; + /* Mac systems come up with some registers not set as we + will need them */ + + /* Clear reset & test bits */ + pci_read_config_byte(pdev, 0x49, ®); + pci_write_config_byte(pdev, 0x49, reg & ~ 0x30); + + /* PCI latency must be > 0x80 for burst mode, tweak it + * if required. + */ + pci_read_config_byte(pdev, PCI_LATENCY_TIMER, ®); + if (reg <= 0x80) + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90); + + /* Enable IRQ output and burst mode */ + pci_read_config_byte(pdev, 0x4a, ®); + pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80); + + } + port_info[0] = port_info[1] = info; + return ata_pci_init_one(pdev, port_info, ports); +} + +static const struct pci_device_id artop_pci_tbl[] = { + { 0x1191, 0x0005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { 0x1191, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, + { 0x1191, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, + { 0x1191, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2}, + { 0x1191, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2}, + { } /* terminate list */ +}; + +static struct pci_driver artop_pci_driver = { + .name = DRV_NAME, + .id_table = artop_pci_tbl, + .probe = artop_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init artop_init(void) +{ + return pci_register_driver(&artop_pci_driver); +} + +static void __exit artop_exit(void) +{ + pci_unregister_driver(&artop_pci_driver); +} + + +module_init(artop_init); +module_exit(artop_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, artop_pci_tbl); +MODULE_VERSION(DRV_VERSION); + |