summaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_hpt37x.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata/pata_hpt37x.c')
-rw-r--r--drivers/ata/pata_hpt37x.c189
1 files changed, 85 insertions, 104 deletions
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 4224cfccede..8839307a64c 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
-#define DRV_VERSION "0.6.14"
+#define DRV_VERSION "0.6.15"
struct hpt_clock {
u8 xfer_speed;
@@ -39,25 +39,24 @@ struct hpt_chip {
/* key for bus clock timings
* bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
* register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
* register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
* register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
- * 31 FIFO enable.
+ * 28 UDMA enable.
+ * 29 DMA enable.
+ * 30 PIO_MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
+ * 31 FIFO enable. Only for PIO.
*/
static struct hpt_clock hpt37x_timings_33[] = {
@@ -384,20 +383,12 @@ static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline)
return ata_sff_prereset(link, deadline);
}
-/**
- * hpt370_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -409,11 +400,31 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
fast |= 0x01;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt37x_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->pio_mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+/**
+ * hpt370_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt370_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -421,33 +432,12 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x02;
- fast |= 0x01;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->dma_mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt370_set_mode(ap, adev, adev->dma_mode);
}
/**
@@ -461,24 +451,25 @@ static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u8 dma_stat = ioread8(ap->ioaddr.bmdma_addr + 2);
- u8 dma_cmd;
void __iomem *bmdma = ap->ioaddr.bmdma_addr;
+ u8 dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+ u8 dma_cmd;
- if (dma_stat & 0x01) {
+ if (dma_stat & ATA_DMA_ACTIVE) {
udelay(20);
- dma_stat = ioread8(bmdma + 2);
+ dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
}
- if (dma_stat & 0x01) {
+ if (dma_stat & ATA_DMA_ACTIVE) {
/* Clear the engine */
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(10);
/* Stop DMA */
- dma_cmd = ioread8(bmdma );
- iowrite8(dma_cmd & 0xFE, bmdma);
+ dma_cmd = ioread8(bmdma + ATA_DMA_CMD);
+ iowrite8(dma_cmd & ~ATA_DMA_START, bmdma + ATA_DMA_CMD);
/* Clear Error */
- dma_stat = ioread8(bmdma + 2);
- iowrite8(dma_stat | 0x06 , bmdma + 2);
+ dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+ iowrite8(dma_stat | ATA_DMA_INTR | ATA_DMA_ERR,
+ bmdma + ATA_DMA_STATUS);
/* Clear the engine */
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(10);
@@ -486,20 +477,12 @@ static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
ata_bmdma_stop(qc);
}
-/**
- * hpt372_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -510,13 +493,32 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt37x_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->pio_mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ * hpt372_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
- printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt372_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -524,33 +526,12 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x07;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, &reg);
- mode = hpt37x_find_mode(ap, adev->dma_mode);
- printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt372_set_mode(ap, adev, adev->dma_mode);
}
/**
@@ -1006,7 +987,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
}
/* Now kick off ATA set up */
- return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data);
+ return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data, 0);
}
static const struct pci_device_id hpt37x[] = {