summaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_hpt3x2n.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata/pata_hpt3x2n.c')
-rw-r--r--drivers/ata/pata_hpt3x2n.c94
1 files changed, 47 insertions, 47 deletions
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 40fcda62c7a..06c8db079b9 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -65,7 +65,7 @@ struct hpt_chip {
* PIO.
* 31 FIFO enable.
*/
-
+
/* 66MHz DPLL clocks */
static struct hpt_clock hpt3x2n_clocks[] = {
@@ -100,11 +100,11 @@ static struct hpt_clock hpt3x2n_clocks[] = {
* is hard coded but easy to change. This will be needed if we use
* different DPLLs
*/
-
+
static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
{
struct hpt_clock *clocks = hpt3x2n_clocks;
-
+
while(clocks->xfer_speed) {
if (clocks->xfer_speed == speed)
return clocks->timing;
@@ -121,52 +121,52 @@ static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
* Perform the initial reset handling for the 3x2n series controllers.
* Reset the hardware and state machine, obtain the cable type.
*/
-
+
static int hpt3xn_pre_reset(struct ata_port *ap)
{
u8 scr2, ata66;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-
+
pci_read_config_byte(pdev, 0x5B, &scr2);
pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
/* Cable register now active */
pci_read_config_byte(pdev, 0x5A, &ata66);
/* Restore state */
pci_write_config_byte(pdev, 0x5B, scr2);
-
+
if (ata66 & (1 << ap->port_no))
ap->cbl = ATA_CBL_PATA40;
else
ap->cbl = ATA_CBL_PATA80;
/* Reset the state machine */
- pci_write_config_byte(pdev, 0x50, 0x37);
- pci_write_config_byte(pdev, 0x54, 0x37);
+ pci_write_config_byte(pdev, 0x50, 0x37);
+ pci_write_config_byte(pdev, 0x54, 0x37);
udelay(100);
return ata_std_prereset(ap);
}
-
+
/**
* hpt3x2n_error_handler - probe the hpt3x2n bus
* @ap: ATA port to reset
*
* Perform the probe reset handling for the 3x2N
*/
-
+
static void hpt3x2n_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
-
+
/**
* hpt3x2n_set_piomode - PIO setup
* @ap: ATA interface
* @adev: device on the interface
*
- * Perform PIO mode setup.
+ * Perform PIO mode setup.
*/
-
+
static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
@@ -177,12 +177,12 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
addr2 = 0x51 + 4 * ap->port_no;
-
+
/* Fast interrupt prediction disable, hold off interrupt disable */
pci_read_config_byte(pdev, addr2, &fast);
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
-
+
pci_read_config_dword(pdev, addr1, &reg);
mode = hpt3x2n_find_mode(ap, adev->pio_mode);
mode &= ~0x8000000; /* No FIFO in PIO */
@@ -199,7 +199,7 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
* Set up the channel for MWDMA or UDMA modes. Much the same as with
* PIO, load the mode number and then set MWDMA or UDMA flag.
*/
-
+
static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
@@ -210,12 +210,12 @@ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
addr2 = 0x51 + 4 * ap->port_no;
-
+
/* Fast interrupt prediction disable, hold off interrupt disable */
pci_read_config_byte(pdev, addr2, &fast);
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
-
+
pci_read_config_dword(pdev, addr1, &reg);
mode = hpt3x2n_find_mode(ap, adev->dma_mode);
mode |= 0x8000000; /* FIFO in MWDMA or UDMA */
@@ -230,14 +230,14 @@ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
*
* Clean up after the HPT3x2n and later DMA engine
*/
-
+
static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int mscreg = 0x50 + 2 * ap->port_no;
u8 bwsr_stat, msc_stat;
-
+
pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
pci_read_config_byte(pdev, mscreg, &msc_stat);
if (bwsr_stat & (1 << ap->port_no))
@@ -257,29 +257,29 @@ static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
* - writing
* - second channel UDMA7 (SATA ports) or higher
* - 66MHz PCI
- *
+ *
* or we will underclock the device and get reduced performance.
*/
-
+
static void hpt3x2n_set_clock(struct ata_port *ap, int source)
{
unsigned long bmdma = ap->ioaddr.bmdma_addr;
-
+
/* Tristate the bus */
outb(0x80, bmdma+0x73);
outb(0x80, bmdma+0x77);
-
+
/* Switch clock and reset channels */
outb(source, bmdma+0x7B);
outb(0xC0, bmdma+0x79);
-
+
/* Reset state machines */
outb(0x37, bmdma+0x70);
outb(0x37, bmdma+0x74);
-
+
/* Complete reset */
outb(0x00, bmdma+0x79);
-
+
/* Reconnect channels to bus */
outb(0x00, bmdma+0x73);
outb(0x00, bmdma+0x77);
@@ -291,7 +291,7 @@ static int hpt3x2n_pair_idle(struct ata_port *ap)
{
struct ata_host *host = ap->host;
struct ata_port *pair = host->ports[ap->port_no ^ 1];
-
+
if (pair->hsm_task_state == HSM_ST_IDLE)
return 1;
return 0;
@@ -305,7 +305,7 @@ static int hpt3x2n_use_dpll(struct ata_port *ap, int reading)
return USE_DPLL; /* Needed for write */
if (flags & PCI66)
return USE_DPLL; /* Needed at 66Mhz */
- return 0;
+ return 0;
}
static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc)
@@ -313,7 +313,7 @@ static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc)
struct ata_taskfile *tf = &qc->tf;
struct ata_port *ap = qc->ap;
int flags = (long)ap->host->private_data;
-
+
if (hpt3x2n_pair_idle(ap)) {
int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE));
if ((flags & USE_DPLL) != dpll) {
@@ -347,13 +347,13 @@ static struct scsi_host_template hpt3x2n_sht = {
/*
* Configuration for HPT3x2n.
*/
-
+
static struct ata_port_operations hpt3x2n_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = hpt3x2n_set_piomode,
.set_dmamode = hpt3x2n_set_dmamode,
.mode_filter = ata_pci_default_filter,
-
+
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
@@ -381,11 +381,11 @@ static struct ata_port_operations hpt3x2n_port_ops = {
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
-};
+};
/**
* hpt3xn_calibrate_dpll - Calibrate the DPLL loop
- * @dev: PCI device
+ * @dev: PCI device
*
* Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this
* succeeds
@@ -396,7 +396,7 @@ static int hpt3xn_calibrate_dpll(struct pci_dev *dev)
u8 reg5b;
u32 reg5c;
int tries;
-
+
for(tries = 0; tries < 0x5000; tries++) {
udelay(50);
pci_read_config_byte(dev, 0x5b, &reg5b);
@@ -422,16 +422,16 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev)
{
unsigned long freq;
u32 fcnt;
-
+
pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt);
if ((fcnt >> 12) != 0xABCDE) {
printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
return 33; /* Not BIOS set */
}
fcnt &= 0x1FF;
-
+
freq = (fcnt * 77) / 192;
-
+
/* Clamp to bands */
if (freq < 40)
return 33;
@@ -471,7 +471,7 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev)
*
* To pin down HPT371N
*/
-
+
static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* HPT372N and friends - UDMA133 */
@@ -488,14 +488,14 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
u8 irqmask;
u32 class_rev;
-
+
unsigned int pci_mhz;
unsigned int f_low, f_high;
int adjust;
-
+
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xFF;
-
+
switch(dev->device) {
case PCI_DEVICE_ID_TTI_HPT366:
if (class_rev < 6)
@@ -530,16 +530,16 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
/* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
50 for UDMA100. Right now we always use 66 */
-
+
pci_mhz = hpt3x2n_pci_clock(dev);
-
+
f_low = (pci_mhz * 48) / 66; /* PCI Mhz for 66Mhz DPLL */
f_high = f_low + 2; /* Tolerance */
-
+
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
/* PLL clock */
pci_write_config_byte(dev, 0x5B, 0x21);
-
+
/* Unlike the 37x we don't try jiggling the frequency */
for(adjust = 0; adjust < 8; adjust++) {
if (hpt3xn_calibrate_dpll(dev))
@@ -554,7 +554,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
port->private_data = NULL;
if (pci_mhz > 60)
port->private_data = (void *)PCI66;
-
+
/* Now kick off ATA set up */
port_info[0] = port_info[1] = port;
return ata_pci_init_one(dev, port_info, 2);