diff options
Diffstat (limited to 'drivers/ata/pata_mpiix.c')
| -rw-r--r-- | drivers/ata/pata_mpiix.c | 113 |
1 files changed, 48 insertions, 65 deletions
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c index 4ccca938675..ca8c965179b 100644 --- a/drivers/ata/pata_mpiix.c +++ b/drivers/ata/pata_mpiix.c @@ -35,7 +35,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_mpiix" -#define DRV_VERSION "0.7.3" +#define DRV_VERSION "0.7.5" enum { IDETIM = 0x6C, /* IDE control register */ @@ -49,12 +49,9 @@ enum { static int mpiix_pre_reset(struct ata_port *ap) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); - static const struct pci_bits mpiix_enable_bits[] = { - { 0x6D, 1, 0x80, 0x80 }, - { 0x6F, 1, 0x80, 0x80 } - }; + static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 }; - if (!pci_test_config_bits(pdev, &mpiix_enable_bits[ap->port_no])) + if (!pci_test_config_bits(pdev, &mpiix_enable_bits)) return -ENOENT; ap->cbl = ATA_CBL_PATA40; return ata_std_prereset(ap); @@ -80,8 +77,8 @@ static void mpiix_error_handler(struct ata_port *ap) * @adev: ATA device * * Called to do the PIO mode setup. The MPIIX allows us to program the - * IORDY sample point (2-5 clocks), recovery 1-4 clocks and whether - * prefetching or iordy are used. + * IORDY sample point (2-5 clocks), recovery (1-4 clocks) and whether + * prefetching or IORDY are used. * * This would get very ugly because we can only program timing for one * device at a time, the other gets PIO0. Fortunately libata calls @@ -103,18 +100,19 @@ static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev) { 2, 3 }, }; pci_read_config_word(pdev, IDETIM, &idetim); - /* Mask the IORDY/TIME/PPE0 bank for this device */ + + /* Mask the IORDY/TIME/PPE for this device */ if (adev->class == ATA_DEV_ATA) - control |= PPE; /* PPE enable for disk */ + control |= PPE; /* Enable prefetch/posting for disk */ if (ata_pio_need_iordy(adev)) - control |= IORDY; /* IORDY */ - if (pio > 0) + control |= IORDY; + if (pio > 1) control |= FTIM; /* This drive is on the fast timing bank */ /* Mask out timing and clear both TIME bank selects */ idetim &= 0xCCEE; - idetim &= ~(0x07 << (2 * adev->devno)); - idetim |= (control << (2 * adev->devno)); + idetim &= ~(0x07 << (4 * adev->devno)); + idetim |= control << (4 * adev->devno); idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8); pci_write_config_word(pdev, IDETIM, idetim); @@ -188,23 +186,24 @@ static struct ata_port_operations mpiix_port_ops = { .qc_prep = ata_qc_prep, .qc_issue = mpiix_qc_issue_prot, - .data_xfer = ata_pio_data_xfer, + .data_xfer = ata_data_xfer, .irq_handler = ata_interrupt, .irq_clear = ata_bmdma_irq_clear, + .irq_on = ata_irq_on, + .irq_ack = ata_irq_ack, .port_start = ata_port_start, - .port_stop = ata_port_stop, - .host_stop = ata_host_stop }; static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id) { /* Single threaded by the PCI probe logic */ - static struct ata_probe_ent probe[2]; + static struct ata_probe_ent probe; static int printed_version; + void __iomem *cmd_addr, *ctl_addr; u16 idetim; - int enabled; + int irq; if (!printed_version++) dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); @@ -217,65 +216,49 @@ static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id) if (!(idetim & ENABLED)) return -ENODEV; + /* See if it's primary or secondary channel... */ + if (!(idetim & SECONDARY)) { + irq = 14; + cmd_addr = devm_ioport_map(&dev->dev, 0x1F0, 8); + ctl_addr = devm_ioport_map(&dev->dev, 0x3F6, 1); + } else { + irq = 15; + cmd_addr = devm_ioport_map(&dev->dev, 0x170, 8); + ctl_addr = devm_ioport_map(&dev->dev, 0x376, 1); + } + + if (!cmd_addr || !ctl_addr) + return -ENOMEM; + /* We do our own plumbing to avoid leaking special cases for whacko ancient hardware into the core code. There are two issues to worry about. #1 The chip is a bridge so if in legacy mode and without BARs set fools the setup. #2 If you pci_disable_device the MPIIX your box goes castors up */ - INIT_LIST_HEAD(&probe[0].node); - probe[0].dev = pci_dev_to_dev(dev); - probe[0].port_ops = &mpiix_port_ops; - probe[0].sht = &mpiix_sht; - probe[0].pio_mask = 0x1F; - probe[0].irq = 14; - probe[0].irq_flags = SA_SHIRQ; - probe[0].port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST; - probe[0].n_ports = 1; - probe[0].port[0].cmd_addr = 0x1F0; - probe[0].port[0].ctl_addr = 0x3F6; - probe[0].port[0].altstatus_addr = 0x3F6; - - /* The secondary lurks at different addresses but is otherwise - the same beastie */ - - INIT_LIST_HEAD(&probe[1].node); - probe[1] = probe[0]; - probe[1].irq = 15; - probe[1].port[0].cmd_addr = 0x170; - probe[1].port[0].ctl_addr = 0x376; - probe[1].port[0].altstatus_addr = 0x376; + INIT_LIST_HEAD(&probe.node); + probe.dev = pci_dev_to_dev(dev); + probe.port_ops = &mpiix_port_ops; + probe.sht = &mpiix_sht; + probe.pio_mask = 0x1F; + probe.irq_flags = SA_SHIRQ; + probe.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST; + probe.n_ports = 1; + + probe.irq = irq; + probe.port[0].cmd_addr = cmd_addr; + probe.port[0].ctl_addr = ctl_addr; + probe.port[0].altstatus_addr = ctl_addr; /* Let libata fill in the port details */ - ata_std_ports(&probe[0].port[0]); - ata_std_ports(&probe[1].port[0]); + ata_std_ports(&probe.port[0]); /* Now add the port that is active */ - enabled = (idetim & SECONDARY) ? 1 : 0; - - if (ata_device_add(&probe[enabled])) + if (ata_device_add(&probe)) return 0; return -ENODEV; } -/** - * mpiix_remove_one - device unload - * @pdev: PCI device being removed - * - * Handle an unplug/unload event for a PCI device. Unload the - * PCI driver but do not use the default handler as we *MUST NOT* - * disable the device as it has other functions. - */ - -static void __devexit mpiix_remove_one(struct pci_dev *pdev) -{ - struct device *dev = pci_dev_to_dev(pdev); - struct ata_host *host = dev_get_drvdata(dev); - - ata_host_remove(host); - dev_set_drvdata(dev, NULL); -} - static const struct pci_device_id mpiix[] = { { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), }, @@ -286,7 +269,7 @@ static struct pci_driver mpiix_pci_driver = { .name = DRV_NAME, .id_table = mpiix, .probe = mpiix_init_one, - .remove = mpiix_remove_one, + .remove = ata_pci_remove_one, .suspend = ata_pci_device_suspend, .resume = ata_pci_device_resume, }; |