diff options
Diffstat (limited to 'drivers/ata/pata_serverworks.c')
| -rw-r--r-- | drivers/ata/pata_serverworks.c | 587 |
1 files changed, 587 insertions, 0 deletions
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c new file mode 100644 index 00000000000..3ec30036c97 --- /dev/null +++ b/drivers/ata/pata_serverworks.c @@ -0,0 +1,587 @@ +/* + * ata-serverworks.c - Serverworks PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based upon + * + * serverworks.c + * + * Copyright (C) 1998-2000 Michel Aubry + * Copyright (C) 1998-2000 Andrzej Krzysztofowicz + * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> + * Portions copyright (c) 2001 Sun Microsystems + * + * + * RCC/ServerWorks IDE driver for Linux + * + * OSB4: `Open South Bridge' IDE Interface (fn 1) + * supports UDMA mode 2 (33 MB/s) + * + * CSB5: `Champion South Bridge' IDE Interface (fn 1) + * all revisions support UDMA mode 4 (66 MB/s) + * revision A2.0 and up support UDMA mode 5 (100 MB/s) + * + * *** The CSB5 does not provide ANY register *** + * *** to detect 80-conductor cable presence. *** + * + * CSB6: `Champion South Bridge' IDE Interface (optional: third channel) + * + * Documentation: + * Available under NDA only. Errata info very hard to get. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_serverworks" +#define DRV_VERSION "0.3.6" + +#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */ +#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */ + +/* Seagate Barracuda ATA IV Family drives in UDMA mode 5 + * can overrun their FIFOs when used with the CSB5 */ + +static const char *csb_bad_ata100[] = { + "ST320011A", + "ST340016A", + "ST360021A", + "ST380021A", + NULL +}; + +/** + * dell_cable - Dell serverworks cable detection + * @ap: ATA port to do cable detect + * + * Dell hide the 40/80 pin select for their interfaces in the top two + * bits of the subsystem ID. + */ + +static int dell_cable(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (pdev->subsystem_device & (1 << (ap->port_no + 14))) + return ATA_CBL_PATA80; + return ATA_CBL_PATA40; +} + +/** + * sun_cable - Sun Cobalt 'Alpine' cable detection + * @ap: ATA port to do cable select + * + * Cobalt CSB5 IDE hides the 40/80pin in the top two bits of the + * subsystem ID the same as dell. We could use one function but we may + * need to extend the Dell one in future + */ + +static int sun_cable(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (pdev->subsystem_device & (1 << (ap->port_no + 14))) + return ATA_CBL_PATA80; + return ATA_CBL_PATA40; +} + +/** + * osb4_cable - OSB4 cable detect + * @ap: ATA port to check + * + * The OSB4 isn't UDMA66 capable so this is easy + */ + +static int osb4_cable(struct ata_port *ap) { + return ATA_CBL_PATA40; +} + +/** + * csb4_cable - CSB5/6 cable detect + * @ap: ATA port to check + * + * Serverworks default arrangement is to use the drive side detection + * only. + */ + +static int csb_cable(struct ata_port *ap) { + return ATA_CBL_PATA80; +} + +struct sv_cable_table { + int device; + int subvendor; + int (*cable_detect)(struct ata_port *ap); +}; + +/* + * Note that we don't copy the old serverworks code because the old + * code contains obvious mistakes + */ + +static struct sv_cable_table cable_detect[] = { + { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_DELL, dell_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_VENDOR_ID_DELL, dell_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_SUN, sun_cable }, + { PCI_DEVICE_ID_SERVERWORKS_OSB4, PCI_ANY_ID, osb4_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, csb_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, csb_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, csb_cable }, + { PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, csb_cable }, + { } +}; + +/** + * serverworks_pre_reset - cable detection + * @ap: ATA port + * + * Perform cable detection according to the device and subvendor + * identifications + */ + +static int serverworks_pre_reset(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct sv_cable_table *cb = cable_detect; + + while(cb->device) { + if (cb->device == pdev->device && + (cb->subvendor == pdev->subsystem_vendor || + cb->subvendor == PCI_ANY_ID)) { + ap->cbl = cb->cable_detect(ap); + return ata_std_prereset(ap); + } + cb++; + } + + BUG(); + return -1; /* kill compiler warning */ +} + +static void serverworks_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, serverworks_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * serverworks_is_csb - Check for CSB or OSB + * @pdev: PCI device to check + * + * Returns true if the device being checked is known to be a CSB + * series device. + */ + +static u8 serverworks_is_csb(struct pci_dev *pdev) +{ + switch (pdev->device) { + case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE: + case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE: + case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2: + case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE: + return 1; + default: + break; + } + return 0; +} + +/** + * serverworks_osb4_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Filter the offered modes for the device to apply controller + * specific rules. OSB4 requires no UDMA for disks due to a FIFO + * bug we hit. + */ + +static unsigned long serverworks_osb4_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + if (adev->class == ATA_DEV_ATA) + mask &= ~ATA_MASK_UDMA; + return ata_pci_default_filter(ap, adev, mask); +} + + +/** + * serverworks_csb_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Check the blacklist and disable UDMA5 if matched + */ + +static unsigned long serverworks_csb_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + const char *p; + char model_num[40]; + int len, i; + + /* Disk, UDMA */ + if (adev->class != ATA_DEV_ATA) + return ata_pci_default_filter(ap, adev, mask); + + /* Actually do need to check */ + ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num)); + /* Precuationary - why not do this in the libata core ?? */ + + len = strlen(model_num); + while ((len > 0) && (model_num[len - 1] == ' ')) { + len--; + model_num[len] = 0; + } + + for(i = 0; (p = csb_bad_ata100[i]) != NULL; i++) { + if (!strncmp(p, model_num, len)) + mask &= ~(0x1F << ATA_SHIFT_UDMA); + } + return ata_pci_default_filter(ap, adev, mask); +} + + +/** + * serverworks_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the OSB4/CSB5 timing registers for PIO. The PIO register + * load is done as a simple lookup. + */ +static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 }; + int offset = 1 + (2 * ap->port_no) - adev->devno; + int devbits = (2 * ap->port_no + adev->devno) * 4; + u16 csb5_pio; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int pio = adev->pio_mode - XFER_PIO_0; + + pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]); + + /* The OSB4 just requires the timing but the CSB series want the + mode number as well */ + if (serverworks_is_csb(pdev)) { + pci_read_config_word(pdev, 0x4A, &csb5_pio); + csb5_pio &= ~(0x0F << devbits); + pci_write_config_byte(pdev, 0x4A, csb5_pio | (pio << devbits)); + } +} + +/** + * serverworks_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5 + * chipset. The MWDMA mode values are pulled from a lookup table + * while the chipset uses mode number for UDMA. + */ + +static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const u8 dma_mode[] = { 0x77, 0x21, 0x20 }; + int offset = 1 + 2 * ap->port_no - adev->devno; + int devbits = (2 * ap->port_no + adev->devno); + u8 ultra; + u8 ultra_cfg; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x54, &ultra_cfg); + + if (adev->dma_mode >= XFER_UDMA_0) { + pci_write_config_byte(pdev, 0x44 + offset, 0x20); + + pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra); + ultra &= ~(0x0F << (ap->port_no * 4)); + ultra |= (adev->dma_mode - XFER_UDMA_0) + << (ap->port_no * 4); + pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra); + + ultra_cfg |= (1 << devbits); + } else { + pci_write_config_byte(pdev, 0x44 + offset, + dma_mode[adev->dma_mode - XFER_MW_DMA_0]); + ultra_cfg &= ~(1 << devbits); + } + pci_write_config_byte(pdev, 0x54, ultra_cfg); +} + +static struct scsi_host_template serverworks_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations serverworks_osb4_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = serverworks_set_piomode, + .set_dmamode = serverworks_set_dmamode, + .mode_filter = serverworks_osb4_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = serverworks_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations serverworks_csb_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = serverworks_set_piomode, + .set_dmamode = serverworks_set_dmamode, + .mode_filter = serverworks_csb_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = serverworks_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int serverworks_fixup_osb4(struct pci_dev *pdev) +{ + u32 reg; + struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, + PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL); + if (isa_dev) { + pci_read_config_dword(isa_dev, 0x64, ®); + reg &= ~0x00002000; /* disable 600ns interrupt mask */ + if (!(reg & 0x00004000)) + printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n"); + reg |= 0x00004000; /* enable UDMA/33 support */ + pci_write_config_dword(isa_dev, 0x64, reg); + pci_dev_put(isa_dev); + return 0; + } + printk(KERN_WARNING "ata_serverworks: Unable to find bridge.\n"); + return -ENODEV; +} + +static int serverworks_fixup_csb(struct pci_dev *pdev) +{ + u8 rev; + u8 btr; + + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); + + /* Third Channel Test */ + if (!(PCI_FUNC(pdev->devfn) & 1)) { + struct pci_dev * findev = NULL; + u32 reg4c = 0; + findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, + PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL); + if (findev) { + pci_read_config_dword(findev, 0x4C, ®4c); + reg4c &= ~0x000007FF; + reg4c |= 0x00000040; + reg4c |= 0x00000020; + pci_write_config_dword(findev, 0x4C, reg4c); + pci_dev_put(findev); + } + } else { + struct pci_dev * findev = NULL; + u8 reg41 = 0; + + findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, + PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL); + if (findev) { + pci_read_config_byte(findev, 0x41, ®41); + reg41 &= ~0x40; + pci_write_config_byte(findev, 0x41, reg41); + pci_dev_put(findev); + } + } + /* setup the UDMA Control register + * + * 1. clear bit 6 to enable DMA + * 2. enable DMA modes with bits 0-1 + * 00 : legacy + * 01 : udma2 + * 10 : udma2/udma4 + * 11 : udma2/udma4/udma5 + */ + pci_read_config_byte(pdev, 0x5A, &btr); + btr &= ~0x40; + if (!(PCI_FUNC(pdev->devfn) & 1)) + btr |= 0x2; + else + btr |= (rev >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2; + pci_write_config_byte(pdev, 0x5A, btr); + + return btr; +} + +static void serverworks_fixup_ht1000(struct pci_dev *pdev) +{ + u8 btr; + /* Setup HT1000 SouthBridge Controller - Single Channel Only */ + pci_read_config_byte(pdev, 0x5A, &btr); + btr &= ~0x40; + btr |= 0x3; + pci_write_config_byte(pdev, 0x5A, btr); +} + + +static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + int ports = 2; + static struct ata_port_info info[4] = { + { /* OSB4 */ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, + .port_ops = &serverworks_osb4_port_ops + }, { /* OSB4 no UDMA */ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x00, + .port_ops = &serverworks_osb4_port_ops + }, { /* CSB5 */ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, + .port_ops = &serverworks_csb_port_ops + }, { /* CSB5 - later revisions*/ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &serverworks_csb_port_ops + } + }; + static struct ata_port_info *port_info[2]; + struct ata_port_info *devinfo = &info[id->driver_data]; + + /* Force master latency timer to 64 PCI clocks */ + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40); + + /* OSB4 : South Bridge and IDE */ + if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) { + /* Select non UDMA capable OSB4 if we can't do fixups */ + if ( serverworks_fixup_osb4(pdev) < 0) + devinfo = &info[1]; + } + /* setup CSB5/CSB6 : South Bridge and IDE option RAID */ + else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) || + (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) || + (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) { + + /* If the returned btr is the newer revision then + select the right info block */ + if (serverworks_fixup_csb(pdev) == 3) + devinfo = &info[3]; + + /* Is this the 3rd channel CSB6 IDE ? */ + if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2) + ports = 1; + } + /* setup HT1000E */ + else if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) + serverworks_fixup_ht1000(pdev); + + if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) + ata_pci_clear_simplex(pdev); + + port_info[0] = port_info[1] = devinfo; + return ata_pci_init_one(pdev, port_info, ports); +} + +static struct pci_device_id serverworks[] = { + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2}, + { 0, }, +}; + +static struct pci_driver serverworks_pci_driver = { + .name = DRV_NAME, + .id_table = serverworks, + .probe = serverworks_init_one, + .remove = ata_pci_remove_one +}; + +static int __init serverworks_init(void) +{ + return pci_register_driver(&serverworks_pci_driver); +} + + +static void __exit serverworks_exit(void) +{ + pci_unregister_driver(&serverworks_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, serverworks); +MODULE_VERSION(DRV_VERSION); + +module_init(serverworks_init); +module_exit(serverworks_exit); |