diff options
Diffstat (limited to 'drivers/ata/pata_sis.c')
| -rw-r--r-- | drivers/ata/pata_sis.c | 1034 |
1 files changed, 1034 insertions, 0 deletions
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c new file mode 100644 index 00000000000..2e555168b43 --- /dev/null +++ b/drivers/ata/pata_sis.c @@ -0,0 +1,1034 @@ +/* + * pata_sis.c - SiS ATA driver + * + * (C) 2005 Red Hat <alan@redhat.com> + * + * Based upon linux/drivers/ide/pci/sis5513.c + * Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org> + * Copyright (C) 2002 Lionel Bouton <Lionel.Bouton@inet6.fr>, Maintainer + * Copyright (C) 2003 Vojtech Pavlik <vojtech@suse.cz> + * SiS Taiwan : for direct support and hardware. + * Daniela Engert : for initial ATA100 advices and numerous others. + * John Fremlin, Manfred Spraul, Dave Morgan, Peter Kjellerstedt : + * for checking code correctness, providing patches. + * Original tests and design on the SiS620 chipset. + * ATA100 tests and design on the SiS735 chipset. + * ATA16/33 support from specs + * ATA133 support for SiS961/962 by L.C. Chang <lcchang@sis.com.tw> + * + * + * TODO + * Check MWDMA on drives that don't support MWDMA speed pio cycles ? + * More Testing + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_sis" +#define DRV_VERSION "0.4.3" + +struct sis_chipset { + u16 device; /* PCI host ID */ + struct ata_port_info *info; /* Info block */ + /* Probably add family, cable detect type etc here to clean + up code later */ +}; + +/** + * sis_port_base - return PCI configuration base for dev + * @adev: device + * + * Returns the base of the PCI configuration registers for this port + * number. + */ + +static int sis_port_base(struct ata_device *adev) +{ + return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno); +} + +/** + * sis_133_pre_reset - check for 40/80 pin + * @ap: Port + * + * Perform cable detection for the later UDMA133 capable + * SiS chipset. + */ + +static int sis_133_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits sis_enable_bits[] = { + { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 tmp; + + if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) { + ata_port_disable(ap); + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + /* The top bit of this register is the cable detect bit */ + pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp); + if (tmp & 0x8000) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + return ata_std_prereset(ap); +} + +/** + * sis_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sis_133_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + + +/** + * sis_66_pre_reset - check for 40/80 pin + * @ap: Port + * + * Perform cable detection on the UDMA66, UDMA100 and early UDMA133 + * SiS IDE controllers. + */ + +static int sis_66_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits sis_enable_bits[] = { + { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 tmp; + + if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) { + ata_port_disable(ap); + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + /* Older chips keep cable detect in bits 4/5 of reg 0x48 */ + pci_read_config_byte(pdev, 0x48, &tmp); + tmp >>= ap->port_no; + if (tmp & 0x10) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + return ata_std_prereset(ap); +} + +/** + * sis_66_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * @classes: + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_66_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sis_66_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * sis_old_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int sis_old_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits sis_enable_bits[] = { + { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) { + ata_port_disable(ap); + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + + +/** + * sis_old_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_old_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sis_old_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * sis_set_fifo - Set RWP fifo bits for this device + * @ap: Port + * @adev: Device + * + * SIS chipsets implement prefetch/postwrite bits for each device + * on both channels. This functionality is not ATAPI compatible and + * must be configured according to the class of device present + */ + +static void sis_set_fifo(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 fifoctrl; + u8 mask = 0x11; + + mask <<= (2 * ap->port_no); + mask <<= adev->devno; + + /* This holds various bits including the FIFO control */ + pci_read_config_byte(pdev, 0x4B, &fifoctrl); + fifoctrl &= ~mask; + + /* Enable for ATA (disk) only */ + if (adev->class == ATA_DEV_ATA) + fifoctrl |= mask; + pci_write_config_byte(pdev, 0x4B, fifoctrl); +} + +/** + * sis_old_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring for. + * + * Set PIO mode for device, in host controller PCI config space. This + * function handles PIO set up for all chips that are pre ATA100 and + * also early ATA100 devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = sis_port_base(adev); + u8 t1, t2; + int speed = adev->pio_mode - XFER_PIO_0; + + const u8 active[] = { 0x00, 0x07, 0x04, 0x03, 0x01 }; + const u8 recovery[] = { 0x00, 0x06, 0x04, 0x03, 0x03 }; + + sis_set_fifo(ap, adev); + + pci_read_config_byte(pdev, port, &t1); + pci_read_config_byte(pdev, port + 1, &t2); + + t1 &= ~0x0F; /* Clear active/recovery timings */ + t2 &= ~0x07; + + t1 |= active[speed]; + t2 |= recovery[speed]; + + pci_write_config_byte(pdev, port, t1); + pci_write_config_byte(pdev, port + 1, t2); +} + +/** + * sis_100_set_pioode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring for. + * + * Set PIO mode for device, in host controller PCI config space. This + * function handles PIO set up for ATA100 devices and early ATA133. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = sis_port_base(adev); + int speed = adev->pio_mode - XFER_PIO_0; + + const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 }; + + sis_set_fifo(ap, adev); + + pci_write_config_byte(pdev, port, actrec[speed]); +} + +/** + * sis_133_set_pioode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring for. + * + * Set PIO mode for device, in host controller PCI config space. This + * function handles PIO set up for the later ATA133 devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x40; + u32 t1; + u32 reg54; + int speed = adev->pio_mode - XFER_PIO_0; + + const u32 timing133[] = { + 0x28269000, /* Recovery << 24 | Act << 16 | Ini << 12 */ + 0x0C266000, + 0x04263000, + 0x0C0A3000, + 0x05093000 + }; + const u32 timing100[] = { + 0x1E1C6000, /* Recovery << 24 | Act << 16 | Ini << 12 */ + 0x091C4000, + 0x031C2000, + 0x09072000, + 0x04062000 + }; + + sis_set_fifo(ap, adev); + + /* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */ + pci_read_config_dword(pdev, 0x54, ®54); + if (reg54 & 0x40000000) + port = 0x70; + port += 8 * ap->port_no + 4 * adev->devno; + + pci_read_config_dword(pdev, port, &t1); + t1 &= 0xC0C00FFF; /* Mask out timing */ + + if (t1 & 0x08) /* 100 or 133 ? */ + t1 |= timing133[speed]; + else + t1 |= timing100[speed]; + pci_write_config_byte(pdev, port, t1); +} + +/** + * sis_old_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles pre UDMA and UDMA33 devices. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 }; + const u16 udma_bits[] = { 0xE000, 0xC000, 0xA000 }; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* bits 3-0 hold recovery timing bits 8-10 active timing and + the higer bits are dependant on the device */ + timing &= ~ 0x870F; + timing |= mwdma_bits[speed]; + pci_write_config_word(pdev, drive_pci, timing); + } else { + /* Bit 15 is UDMA on/off, bit 13-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x6000; + timing |= udma_bits[speed]; + } +} + +/** + * sis_66_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles UDMA66 and early UDMA100 devices. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 }; + const u16 udma_bits[] = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000}; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* bits 3-0 hold recovery timing bits 8-10 active timing and + the higer bits are dependant on the device, bit 15 udma */ + timing &= ~ 0x870F; + timing |= mwdma_bits[speed]; + } else { + /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x6000; + timing |= udma_bits[speed]; + } + pci_write_config_word(pdev, drive_pci, timing); +} + +/** + * sis_100_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles UDMA66 and early UDMA100 devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 udma_bits[] = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100}; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */ + } else { + /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x0F00; + timing |= udma_bits[speed]; + } + pci_write_config_word(pdev, drive_pci, timing); +} + +/** + * sis_133_early_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles early SiS 961 bridges. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100}; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */ + } else { + /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x0F00; + timing |= udma_bits[speed]; + } + pci_write_config_word(pdev, drive_pci, timing); +} + +/** + * sis_133_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles early SiS 961 bridges. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int port = 0x40; + u32 t1; + u32 reg54; + + /* bits 4- cycle time 8 - cvs time */ + const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 }; + const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 }; + + /* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */ + pci_read_config_dword(pdev, 0x54, ®54); + if (reg54 & 0x40000000) + port = 0x70; + port += (8 * ap->port_no) + (4 * adev->devno); + + pci_read_config_dword(pdev, port, &t1); + + if (adev->dma_mode < XFER_UDMA_0) { + t1 &= ~0x00000004; + /* FIXME: need data sheet to add MWDMA here. Also lacking on + ide/pci driver */ + } else { + speed = adev->dma_mode - XFER_UDMA_0; + /* if & 8 no UDMA133 - need info for ... */ + t1 &= ~0x00000FF0; + t1 |= 0x00000004; + if (t1 & 0x08) + t1 |= timing_u133[speed]; + else + t1 |= timing_u100[speed]; + } + pci_write_config_dword(pdev, port, t1); +} + +static struct scsi_host_template sis_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations sis_133_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_133_set_piomode, + .set_dmamode = sis_133_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_133_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_133_early_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_100_set_piomode, + .set_dmamode = sis_133_early_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_66_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_100_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_100_set_piomode, + .set_dmamode = sis_100_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_66_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_66_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_old_set_piomode, + .set_dmamode = sis_66_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_66_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_old_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_old_set_piomode, + .set_dmamode = sis_old_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_old_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .eng_timeout = ata_eng_timeout, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static struct ata_port_info sis_info = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, + .udma_mask = 0, + .port_ops = &sis_old_ops, +}; +static struct ata_port_info sis_info33 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA2, /* UDMA 33 */ + .port_ops = &sis_old_ops, +}; +static struct ata_port_info sis_info66 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA4, /* UDMA 66 */ + .port_ops = &sis_66_ops, +}; +static struct ata_port_info sis_info100 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA5, + .port_ops = &sis_100_ops, +}; +static struct ata_port_info sis_info100_early = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .udma_mask = ATA_UDMA5, + .pio_mask = 0x1f, /* pio0-4 */ + .port_ops = &sis_66_ops, +}; +static struct ata_port_info sis_info133 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA6, + .port_ops = &sis_133_ops, +}; +static struct ata_port_info sis_info133_early = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA6, + .port_ops = &sis_133_early_ops, +}; + + +static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis) +{ + u16 regw; + u8 reg; + + if (sis->info == &sis_info133) { + pci_read_config_word(pdev, 0x50, ®w); + if (regw & 0x08) + pci_write_config_word(pdev, 0x50, regw & ~0x08); + pci_read_config_word(pdev, 0x52, ®w); + if (regw & 0x08) + pci_write_config_word(pdev, 0x52, regw & ~0x08); + return; + } + + if (sis->info == &sis_info133_early || sis->info == &sis_info100) { + /* Fix up latency */ + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80); + /* Set compatibility bit */ + pci_read_config_byte(pdev, 0x49, ®); + if (!(reg & 0x01)) + pci_write_config_byte(pdev, 0x49, reg | 0x01); + return; + } + + if (sis->info == &sis_info66 || sis->info == &sis_info100_early) { + /* Fix up latency */ + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80); + /* Set compatibility bit */ + pci_read_config_byte(pdev, 0x52, ®); + if (!(reg & 0x04)) + pci_write_config_byte(pdev, 0x52, reg | 0x04); + return; + } + + if (sis->info == &sis_info33) { + pci_read_config_byte(pdev, PCI_CLASS_PROG, ®); + if (( reg & 0x0F ) != 0x00) + pci_write_config_byte(pdev, PCI_CLASS_PROG, reg & 0xF0); + /* Fall through to ATA16 fixup below */ + } + + if (sis->info == &sis_info || sis->info == &sis_info33) { + /* force per drive recovery and active timings + needed on ATA_33 and below chips */ + pci_read_config_byte(pdev, 0x52, ®); + if (!(reg & 0x08)) + pci_write_config_byte(pdev, 0x52, reg|0x08); + return; + } + + BUG(); +} + +/** + * sis_init_one - Register SiS ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in sis_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. We probe for combined mode (sigh), + * and then hand over control to libata, for it to do the rest. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + static struct ata_port_info *port_info[2]; + struct ata_port_info *port; + struct pci_dev *host = NULL; + struct sis_chipset *chipset = NULL; + + static struct sis_chipset sis_chipsets[] = { + + { 0x0968, &sis_info133 }, + { 0x0966, &sis_info133 }, + { 0x0965, &sis_info133 }, + { 0x0745, &sis_info100 }, + { 0x0735, &sis_info100 }, + { 0x0733, &sis_info100 }, + { 0x0635, &sis_info100 }, + { 0x0633, &sis_info100 }, + + { 0x0730, &sis_info100_early }, /* 100 with ATA 66 layout */ + { 0x0550, &sis_info100_early }, /* 100 with ATA 66 layout */ + + { 0x0640, &sis_info66 }, + { 0x0630, &sis_info66 }, + { 0x0620, &sis_info66 }, + { 0x0540, &sis_info66 }, + { 0x0530, &sis_info66 }, + + { 0x5600, &sis_info33 }, + { 0x5598, &sis_info33 }, + { 0x5597, &sis_info33 }, + { 0x5591, &sis_info33 }, + { 0x5582, &sis_info33 }, + { 0x5581, &sis_info33 }, + + { 0x5596, &sis_info }, + { 0x5571, &sis_info }, + { 0x5517, &sis_info }, + { 0x5511, &sis_info }, + + {0} + }; + static struct sis_chipset sis133_early = { + 0x0, &sis_info133_early + }; + static struct sis_chipset sis133 = { + 0x0, &sis_info133 + }; + static struct sis_chipset sis100_early = { + 0x0, &sis_info100_early + }; + static struct sis_chipset sis100 = { + 0x0, &sis_info100 + }; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + /* We have to find the bridge first */ + + for (chipset = &sis_chipsets[0]; chipset->device; chipset++) { + host = pci_get_device(PCI_VENDOR_ID_SI, chipset->device, NULL); + if (host != NULL) { + if (chipset->device == 0x630) { /* SIS630 */ + u8 host_rev; + pci_read_config_byte(host, PCI_REVISION_ID, &host_rev); + if (host_rev >= 0x30) /* 630 ET */ + chipset = &sis100_early; + } + break; + } + } + + /* Look for concealed bridges */ + if (host == NULL) { + /* Second check */ + u32 idemisc; + u16 trueid; + + /* Disable ID masking and register remapping then + see what the real ID is */ + + pci_read_config_dword(pdev, 0x54, &idemisc); + pci_write_config_dword(pdev, 0x54, idemisc & 0x7fffffff); + pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid); + pci_write_config_dword(pdev, 0x54, idemisc); + + switch(trueid) { + case 0x5518: /* SIS 962/963 */ + chipset = &sis133; + if ((idemisc & 0x40000000) == 0) { + pci_write_config_dword(pdev, 0x54, idemisc | 0x40000000); + printk(KERN_INFO "SIS5513: Switching to 5513 register mapping\n"); + } + break; + case 0x0180: /* SIS 965/965L */ + chipset = &sis133; + break; + case 0x1180: /* SIS 966/966L */ + chipset = &sis133; + break; + } + } + + /* Further check */ + if (chipset == NULL) { + struct pci_dev *lpc_bridge; + u16 trueid; + u8 prefctl; + u8 idecfg; + u8 sbrev; + + /* Try the second unmasking technique */ + pci_read_config_byte(pdev, 0x4a, &idecfg); + pci_write_config_byte(pdev, 0x4a, idecfg | 0x10); + pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid); + pci_write_config_byte(pdev, 0x4a, idecfg); + + switch(trueid) { + case 0x5517: + lpc_bridge = pci_get_slot(pdev->bus, 0x10); /* Bus 0 Dev 2 Fn 0 */ + if (lpc_bridge == NULL) + break; + pci_read_config_byte(lpc_bridge, PCI_REVISION_ID, &sbrev); + pci_read_config_byte(pdev, 0x49, &prefctl); + pci_dev_put(lpc_bridge); + + if (sbrev == 0x10 && (prefctl & 0x80)) { + chipset = &sis133_early; + break; + } + chipset = &sis100; + break; + } + } + pci_dev_put(host); + + /* No chipset info, no support */ + if (chipset == NULL) + return -ENODEV; + + port = chipset->info; + port->private_data = chipset; + + sis_fixup(pdev, chipset); + + port_info[0] = port_info[1] = port; + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id sis_pci_tbl[] = { + { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5513), }, /* SiS 5513 */ + { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5518), }, /* SiS 5518 */ + { } +}; + +static struct pci_driver sis_pci_driver = { + .name = DRV_NAME, + .id_table = sis_pci_tbl, + .probe = sis_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init sis_init(void) +{ + return pci_register_driver(&sis_pci_driver); +} + +static void __exit sis_exit(void) +{ + pci_unregister_driver(&sis_pci_driver); +} + + +module_init(sis_init); +module_exit(sis_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for SiS ATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sis_pci_tbl); +MODULE_VERSION(DRV_VERSION); + |