diff options
Diffstat (limited to 'drivers/ata')
61 files changed, 44946 insertions, 0 deletions
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig new file mode 100644 index 00000000000..3f4aa0c99ee --- /dev/null +++ b/drivers/ata/Kconfig @@ -0,0 +1,487 @@ +# +# SATA/PATA driver configuration +# + +menu "Serial ATA (prod) and Parallel ATA (experimental) drivers" + +config ATA + tristate "ATA device support" + depends on !(M32R || M68K) || BROKEN + depends on !SUN4 || BROKEN + select SCSI + ---help--- + If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or + any other ATA device under Linux, say Y and make sure that you know + the name of your ATA host adapter (the card inside your computer + that "speaks" the ATA protocol, also called ATA controller), + because you will be asked for it. + +if ATA + +config SATA_AHCI + tristate "AHCI SATA support" + depends on PCI + help + This option enables support for AHCI Serial ATA. + + If unsure, say N. + +config SATA_SVW + tristate "ServerWorks Frodo / Apple K2 SATA support" + depends on PCI + help + This option enables support for Broadcom/Serverworks/Apple K2 + SATA support. + + If unsure, say N. + +config ATA_PIIX + tristate "Intel PIIX/ICH SATA support" + depends on PCI + help + This option enables support for ICH5/6/7/8 Serial ATA. + If PATA support was enabled previously, this enables + support for select Intel PIIX/ICH PATA host controllers. + + If unsure, say N. + +config SATA_MV + tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the Marvell Serial ATA family. + Currently supports 88SX[56]0[48][01] chips. + + If unsure, say N. + +config SATA_NV + tristate "NVIDIA SATA support" + depends on PCI + help + This option enables support for NVIDIA Serial ATA. + + If unsure, say N. + +config PDC_ADMA + tristate "Pacific Digital ADMA support" + depends on PCI + help + This option enables support for Pacific Digital ADMA controllers + + If unsure, say N. + +config SATA_QSTOR + tristate "Pacific Digital SATA QStor support" + depends on PCI + help + This option enables support for Pacific Digital Serial ATA QStor. + + If unsure, say N. + +config SATA_PROMISE + tristate "Promise SATA TX2/TX4 support" + depends on PCI + help + This option enables support for Promise Serial ATA TX2/TX4. + + If unsure, say N. + +config SATA_SX4 + tristate "Promise SATA SX4 support" + depends on PCI && EXPERIMENTAL + help + This option enables support for Promise Serial ATA SX4. + + If unsure, say N. + +config SATA_SIL + tristate "Silicon Image SATA support" + depends on PCI + help + This option enables support for Silicon Image Serial ATA. + + If unsure, say N. + +config SATA_SIL24 + tristate "Silicon Image 3124/3132 SATA support" + depends on PCI + help + This option enables support for Silicon Image 3124/3132 Serial ATA. + + If unsure, say N. + +config SATA_SIS + tristate "SiS 964/180 SATA support" + depends on PCI + help + This option enables support for SiS Serial ATA 964/180. + + If unsure, say N. + +config SATA_ULI + tristate "ULi Electronics SATA support" + depends on PCI + help + This option enables support for ULi Electronics SATA. + + If unsure, say N. + +config SATA_VIA + tristate "VIA SATA support" + depends on PCI + help + This option enables support for VIA Serial ATA. + + If unsure, say N. + +config SATA_VITESSE + tristate "VITESSE VSC-7174 / INTEL 31244 SATA support" + depends on PCI + help + This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA. + + If unsure, say N. + +config SATA_INTEL_COMBINED + bool + depends on IDE=y && !BLK_DEV_IDE_SATA && (SATA_AHCI || ATA_PIIX) + default y + +config PATA_ALI + tristate "ALi PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the ALi ATA interfaces + found on the many ALi chipsets. + + If unsure, say N. + +config PATA_AMD + tristate "AMD/NVidia PATA support (Experimental)" + depends on PCI + help + This option enables support for the AMD and NVidia PATA + interfaces found on the chipsets for Athlon/Athlon64. + + If unsure, say N. + +config PATA_ARTOP + tristate "ARTOP 6210/6260 PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for ARTOP PATA controllers. + + If unsure, say N. + +config PATA_ATIIXP + tristate "ATI PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the ATI ATA interfaces + found on the many ATI chipsets. + + If unsure, say N. + +config PATA_CMD64X + tristate "CMD64x PATA support (Very Experimental)" + depends on PCI&& EXPERIMENTAL + help + This option enables support for the CMD64x series chips + except for the CMD640. + + If unsure, say N. + +config PATA_CS5520 + tristate "CS5510/5520 PATA support" + depends on PCI + help + This option enables support for the Cyrix 5510/5520 + companion chip used with the MediaGX/Geode processor family. + + If unsure, say N. + +config PATA_CS5530 + tristate "CS5530 PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the Cyrix/NatSemi/AMD CS5530 + companion chip used with the MediaGX/Geode processor family. + + If unsure, say N. + +config PATA_CS5535 + tristate "CS5535 PATA support (Experimental)" + depends on PCI && X86 && !X86_64 && EXPERIMENTAL + help + This option enables support for the NatSemi/AMD CS5535 + companion chip used with the Geode processor family. + + If unsure, say N. + +config PATA_CYPRESS + tristate "Cypress CY82C693 PATA support (Very Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the Cypress/Contaq CY82C693 + chipset found in some Alpha systems + + If unsure, say N. + +config PATA_EFAR + tristate "EFAR SLC90E66 support" + depends on PCI + help + This option enables support for the EFAR SLC90E66 + IDE controller found on some older machines. + + If unsure, say N. + +config ATA_GENERIC + tristate "Generic ATA support" + depends on PCI + help + This option enables support for generic BIOS configured + ATA controllers via the new ATA layer + + If unsure, say N. + +config PATA_HPT366 + tristate "HPT 366/368 PATA support (Very Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the HPT 366 and 368 + PATA controllers via the new ATA layer. + + If unsure, say N. + +config PATA_HPT37X + tristate "HPT 370/370A/371/372/374/302 PATA support (Very Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the majority of the later HPT + PATA controllers via the new ATA layer. + + If unsure, say N. + +config PATA_HPT3X2N + tristate "HPT 372N/302N PATA support (Very Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the N variant HPT PATA + controllers via the new ATA layer + + If unsure, say N. + +config PATA_HPT3X3 + tristate "HPT 343/363 PATA support (Experimental)" + depends on PCI + help + This option enables support for the HPT 343/363 + PATA controllers via the new ATA layer + + If unsure, say N. + +config PATA_ISAPNP + tristate "ISA Plug and Play PATA support (Very Experimental)" + depends on EXPERIMENTAL && ISAPNP + help + This option enables support for ISA plug & play ATA + controllers such as those found on old soundcards. + + If unsure, say N. + +config PATA_IT821X + tristate "IT821x PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the ITE 8211 and 8212 + PATA controllers via the new ATA layer, including RAID + mode. + + If unsure, say N. + +config PATA_JMICRON + tristate "JMicron PATA support" + depends on PCI + help + Enable support for the JMicron IDE controller, via the new + ATA layer. + + If unsure, say N. + +config PATA_LEGACY + tristate "Legacy ISA PATA support (Experimental)" + depends on ISA && EXPERIMENTAL + help + This option enables support for ISA/VLB bus legacy PATA + ports and allows them to be accessed via the new ATA layer. + + If unsure, say N. + +config PATA_TRIFLEX + tristate "Compaq Triflex PATA support" + depends on PCI + help + Enable support for the Compaq 'Triflex' IDE controller as found + on many Compaq Pentium-Pro systems, via the new ATA layer. + + If unsure, say N. + +config PATA_MPIIX + tristate "Intel PATA MPIIX support" + depends on PCI + help + This option enables support for MPIIX PATA support. + + If unsure, say N. + +config PATA_OLDPIIX + tristate "Intel PATA old PIIX support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for old(?) PIIX PATA support. + + If unsure, say N. + +config PATA_NETCELL + tristate "NETCELL Revolution RAID support" + depends on PCI + help + This option enables support for the Netcell Revolution RAID + PATA controller. + + If unsure, say N. + +config PATA_NS87410 + tristate "Nat Semi NS87410 PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the National Semiconductor + NS87410 PCI-IDE controller. + + If unsure, say N. + +config PATA_OPTI + tristate "OPTI621/6215 PATA support (Very Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables full PIO support for the early Opti ATA + controllers found on some old motherboards. + + If unsure, say N. + +config PATA_OPTIDMA + tristate "OPTI FireStar PATA support (Veyr Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables DMA/PIO support for the later OPTi + controllers found on some old motherboards and in some + latops + + If unsure, say N. + +config PATA_PCMCIA + tristate "PCMCIA PATA support" + depends on PCMCIA + help + This option enables support for PCMCIA ATA interfaces, including + compact flash card adapters via the new ATA layer. + + If unsure, say N. + +config PATA_PDC_OLD + tristate "Older Promise PATA controller support (Very Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the Promise 20246, 20262, 20263, + 20265 and 20267 adapters. + + If unsure, say N. + +config PATA_QDI + tristate "QDI VLB PATA support" + depends on ISA + help + Support for QDI 6500 and 6580 PATA controllers on VESA local bus. + +config PATA_RADISYS + tristate "RADISYS 82600 PATA support (Very experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the RADISYS 82600 + PATA controllers via the new ATA layer + + If unsure, say N. + +config PATA_RZ1000 + tristate "PC Tech RZ1000 PATA support" + depends on PCI + help + This option enables basic support for the PC Tech RZ1000/1 + PATA controllers via the new ATA layer + + If unsure, say N. + +config PATA_SC1200 + tristate "SC1200 PATA support (Raving Lunatic)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the NatSemi/AMD SC1200 SoC + companion chip used with the Geode processor family. + + If unsure, say N. + +config PATA_SERVERWORKS + tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for the Serverworks OSB4/CSB5/CSB6 and + HT1000 PATA controllers, via the new ATA layer. + + If unsure, say N. + +config PATA_PDC2027X + tristate "Promise PATA 2027x support" + depends on PCI + help + This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. + + If unsure, say N. + +config PATA_SIL680 + tristate "CMD / Silicon Image 680 PATA support" + depends on PCI + help + This option enables support for CMD / Silicon Image 680 PATA. + + If unsure, say N. + +config PATA_SIS + tristate "SiS PATA support (Experimental)" + depends on PCI && EXPERIMENTAL + help + This option enables support for SiS PATA controllers + + If unsure, say N. + +config PATA_VIA + tristate "VIA PATA support" + depends on PCI + help + This option enables support for the VIA PATA interfaces + found on the many VIA chipsets. + + If unsure, say N. + +config PATA_WINBOND + tristate "Winbond SL82C105 PATA support" + depends on PCI + help + This option enables support for SL82C105 PATA devices found in the + Netwinder and some other systems + + If unsure, say N. + +endif +endmenu + diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile new file mode 100644 index 00000000000..72243a677f9 --- /dev/null +++ b/drivers/ata/Makefile @@ -0,0 +1,62 @@ + +obj-$(CONFIG_ATA) += libata.o + +obj-$(CONFIG_SATA_AHCI) += ahci.o +obj-$(CONFIG_SATA_SVW) += sata_svw.o +obj-$(CONFIG_ATA_PIIX) += ata_piix.o +obj-$(CONFIG_SATA_PROMISE) += sata_promise.o +obj-$(CONFIG_SATA_QSTOR) += sata_qstor.o +obj-$(CONFIG_SATA_SIL) += sata_sil.o +obj-$(CONFIG_SATA_SIL24) += sata_sil24.o +obj-$(CONFIG_SATA_VIA) += sata_via.o +obj-$(CONFIG_SATA_VITESSE) += sata_vsc.o +obj-$(CONFIG_SATA_SIS) += sata_sis.o +obj-$(CONFIG_SATA_SX4) += sata_sx4.o +obj-$(CONFIG_SATA_NV) += sata_nv.o +obj-$(CONFIG_SATA_ULI) += sata_uli.o +obj-$(CONFIG_SATA_MV) += sata_mv.o +obj-$(CONFIG_PDC_ADMA) += pdc_adma.o + +obj-$(CONFIG_PATA_ALI) += pata_ali.o +obj-$(CONFIG_PATA_AMD) += pata_amd.o +obj-$(CONFIG_PATA_ARTOP) += pata_artop.o +obj-$(CONFIG_PATA_ATIIXP) += pata_atiixp.o +obj-$(CONFIG_PATA_CMD64X) += pata_cmd64x.o +obj-$(CONFIG_PATA_CS5520) += pata_cs5520.o +obj-$(CONFIG_PATA_CS5530) += pata_cs5530.o +obj-$(CONFIG_PATA_CS5535) += pata_cs5535.o +obj-$(CONFIG_PATA_CYPRESS) += pata_cypress.o +obj-$(CONFIG_PATA_EFAR) += pata_efar.o +obj-$(CONFIG_PATA_HPT366) += pata_hpt366.o +obj-$(CONFIG_PATA_HPT37X) += pata_hpt37x.o +obj-$(CONFIG_PATA_HPT3X2N) += pata_hpt3x2n.o +obj-$(CONFIG_PATA_HPT3X3) += pata_hpt3x3.o +obj-$(CONFIG_PATA_ISAPNP) += pata_isapnp.o +obj-$(CONFIG_PATA_IT821X) += pata_it821x.o +obj-$(CONFIG_PATA_JMICRON) += pata_jmicron.o +obj-$(CONFIG_PATA_NETCELL) += pata_netcell.o +obj-$(CONFIG_PATA_NS87410) += pata_ns87410.o +obj-$(CONFIG_PATA_OPTI) += pata_opti.o +obj-$(CONFIG_PATA_OPTIDMA) += pata_optidma.o +obj-$(CONFIG_PATA_MPIIX) += pata_mpiix.o +obj-$(CONFIG_PATA_OLDPIIX) += pata_oldpiix.o +obj-$(CONFIG_PATA_PCMCIA) += pata_pcmcia.o +obj-$(CONFIG_PATA_PDC2027X) += pata_pdc2027x.o +obj-$(CONFIG_PATA_PDC_OLD) += pata_pdc202xx_old.o +obj-$(CONFIG_PATA_QDI) += pata_qdi.o +obj-$(CONFIG_PATA_RADISYS) += pata_radisys.o +obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o +obj-$(CONFIG_PATA_SC1200) += pata_sc1200.o +obj-$(CONFIG_PATA_SERVERWORKS) += pata_serverworks.o +obj-$(CONFIG_PATA_SIL680) += pata_sil680.o +obj-$(CONFIG_PATA_VIA) += pata_via.o +obj-$(CONFIG_PATA_WINBOND) += pata_sl82c105.o +obj-$(CONFIG_PATA_SIS) += pata_sis.o +obj-$(CONFIG_PATA_TRIFLEX) += pata_triflex.o +# Should be last but one libata driver +obj-$(CONFIG_ATA_GENERIC) += ata_generic.o +# Should be last libata driver +obj-$(CONFIG_PATA_LEGACY) += pata_legacy.o + +libata-objs := libata-core.o libata-scsi.o libata-sff.o libata-eh.o + diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c new file mode 100644 index 00000000000..1aabc81d82f --- /dev/null +++ b/drivers/ata/ahci.c @@ -0,0 +1,1684 @@ +/* + * ahci.c - AHCI SATA support + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2004-2005 Red Hat, Inc. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * AHCI hardware documentation: + * http://www.intel.com/technology/serialata/pdf/rev1_0.pdf + * http://www.intel.com/technology/serialata/pdf/rev1_1.pdf + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/dma-mapping.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <linux/libata.h> +#include <asm/io.h> + +#define DRV_NAME "ahci" +#define DRV_VERSION "2.0" + + +enum { + AHCI_PCI_BAR = 5, + AHCI_MAX_SG = 168, /* hardware max is 64K */ + AHCI_DMA_BOUNDARY = 0xffffffff, + AHCI_USE_CLUSTERING = 0, + AHCI_MAX_CMDS = 32, + AHCI_CMD_SZ = 32, + AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ, + AHCI_RX_FIS_SZ = 256, + AHCI_CMD_TBL_CDB = 0x40, + AHCI_CMD_TBL_HDR_SZ = 0x80, + AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16), + AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS, + AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ + + AHCI_RX_FIS_SZ, + AHCI_IRQ_ON_SG = (1 << 31), + AHCI_CMD_ATAPI = (1 << 5), + AHCI_CMD_WRITE = (1 << 6), + AHCI_CMD_PREFETCH = (1 << 7), + AHCI_CMD_RESET = (1 << 8), + AHCI_CMD_CLR_BUSY = (1 << 10), + + RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */ + RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */ + + board_ahci = 0, + board_ahci_vt8251 = 1, + + /* global controller registers */ + HOST_CAP = 0x00, /* host capabilities */ + HOST_CTL = 0x04, /* global host control */ + HOST_IRQ_STAT = 0x08, /* interrupt status */ + HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */ + HOST_VERSION = 0x10, /* AHCI spec. version compliancy */ + + /* HOST_CTL bits */ + HOST_RESET = (1 << 0), /* reset controller; self-clear */ + HOST_IRQ_EN = (1 << 1), /* global IRQ enable */ + HOST_AHCI_EN = (1 << 31), /* AHCI enabled */ + + /* HOST_CAP bits */ + HOST_CAP_SSC = (1 << 14), /* Slumber capable */ + HOST_CAP_CLO = (1 << 24), /* Command List Override support */ + HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */ + HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */ + HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */ + + /* registers for each SATA port */ + PORT_LST_ADDR = 0x00, /* command list DMA addr */ + PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */ + PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */ + PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */ + PORT_IRQ_STAT = 0x10, /* interrupt status */ + PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */ + PORT_CMD = 0x18, /* port command */ + PORT_TFDATA = 0x20, /* taskfile data */ + PORT_SIG = 0x24, /* device TF signature */ + PORT_CMD_ISSUE = 0x38, /* command issue */ + PORT_SCR = 0x28, /* SATA phy register block */ + PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */ + PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */ + PORT_SCR_ERR = 0x30, /* SATA phy register: SError */ + PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */ + + /* PORT_IRQ_{STAT,MASK} bits */ + PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */ + PORT_IRQ_TF_ERR = (1 << 30), /* task file error */ + PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */ + PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */ + PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */ + PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */ + PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */ + PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */ + + PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */ + PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */ + PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */ + PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */ + PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */ + PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */ + PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */ + PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */ + PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */ + + PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR | + PORT_IRQ_IF_ERR | + PORT_IRQ_CONNECT | + PORT_IRQ_PHYRDY | + PORT_IRQ_UNK_FIS, + PORT_IRQ_ERROR = PORT_IRQ_FREEZE | + PORT_IRQ_TF_ERR | + PORT_IRQ_HBUS_DATA_ERR, + DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE | + PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS | + PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS, + + /* PORT_CMD bits */ + PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */ + PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */ + PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */ + PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */ + PORT_CMD_CLO = (1 << 3), /* Command list override */ + PORT_CMD_POWER_ON = (1 << 2), /* Power up device */ + PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */ + PORT_CMD_START = (1 << 0), /* Enable port DMA engine */ + + PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */ + PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */ + PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */ + PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */ + + /* hpriv->flags bits */ + AHCI_FLAG_MSI = (1 << 0), + + /* ap->flags bits */ + AHCI_FLAG_RESET_NEEDS_CLO = (1 << 24), + AHCI_FLAG_NO_NCQ = (1 << 25), +}; + +struct ahci_cmd_hdr { + u32 opts; + u32 status; + u32 tbl_addr; + u32 tbl_addr_hi; + u32 reserved[4]; +}; + +struct ahci_sg { + u32 addr; + u32 addr_hi; + u32 reserved; + u32 flags_size; +}; + +struct ahci_host_priv { + unsigned long flags; + u32 cap; /* cache of HOST_CAP register */ + u32 port_map; /* cache of HOST_PORTS_IMPL reg */ +}; + +struct ahci_port_priv { + struct ahci_cmd_hdr *cmd_slot; + dma_addr_t cmd_slot_dma; + void *cmd_tbl; + dma_addr_t cmd_tbl_dma; + void *rx_fis; + dma_addr_t rx_fis_dma; +}; + +static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); +static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc); +static irqreturn_t ahci_interrupt (int irq, void *dev_instance, struct pt_regs *regs); +static void ahci_irq_clear(struct ata_port *ap); +static int ahci_port_start(struct ata_port *ap); +static void ahci_port_stop(struct ata_port *ap); +static void ahci_tf_read(struct ata_port *ap, struct ata_taskfile *tf); +static void ahci_qc_prep(struct ata_queued_cmd *qc); +static u8 ahci_check_status(struct ata_port *ap); +static void ahci_freeze(struct ata_port *ap); +static void ahci_thaw(struct ata_port *ap); +static void ahci_error_handler(struct ata_port *ap); +static void ahci_post_internal_cmd(struct ata_queued_cmd *qc); +static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg); +static int ahci_port_resume(struct ata_port *ap); +static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg); +static int ahci_pci_device_resume(struct pci_dev *pdev); +static void ahci_remove_one (struct pci_dev *pdev); + +static struct scsi_host_template ahci_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .change_queue_depth = ata_scsi_change_queue_depth, + .can_queue = AHCI_MAX_CMDS - 1, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = AHCI_MAX_SG, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = AHCI_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = AHCI_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, + .suspend = ata_scsi_device_suspend, + .resume = ata_scsi_device_resume, +}; + +static const struct ata_port_operations ahci_ops = { + .port_disable = ata_port_disable, + + .check_status = ahci_check_status, + .check_altstatus = ahci_check_status, + .dev_select = ata_noop_dev_select, + + .tf_read = ahci_tf_read, + + .qc_prep = ahci_qc_prep, + .qc_issue = ahci_qc_issue, + + .irq_handler = ahci_interrupt, + .irq_clear = ahci_irq_clear, + + .scr_read = ahci_scr_read, + .scr_write = ahci_scr_write, + + .freeze = ahci_freeze, + .thaw = ahci_thaw, + + .error_handler = ahci_error_handler, + .post_internal_cmd = ahci_post_internal_cmd, + + .port_suspend = ahci_port_suspend, + .port_resume = ahci_port_resume, + + .port_start = ahci_port_start, + .port_stop = ahci_port_stop, +}; + +static const struct ata_port_info ahci_port_info[] = { + /* board_ahci */ + { + .sht = &ahci_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | + ATA_FLAG_SKIP_D2H_BSY, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &ahci_ops, + }, + /* board_ahci_vt8251 */ + { + .sht = &ahci_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | + ATA_FLAG_SKIP_D2H_BSY | + AHCI_FLAG_RESET_NEEDS_CLO | AHCI_FLAG_NO_NCQ, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &ahci_ops, + }, +}; + +static const struct pci_device_id ahci_pci_tbl[] = { + /* Intel */ + { PCI_VENDOR_ID_INTEL, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH6 */ + { PCI_VENDOR_ID_INTEL, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH6M */ + { PCI_VENDOR_ID_INTEL, 0x27c1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH7 */ + { PCI_VENDOR_ID_INTEL, 0x27c5, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH7M */ + { PCI_VENDOR_ID_INTEL, 0x27c3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH7R */ + { PCI_VENDOR_ID_AL, 0x5288, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ULi M5288 */ + { PCI_VENDOR_ID_INTEL, 0x2681, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ESB2 */ + { PCI_VENDOR_ID_INTEL, 0x2682, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ESB2 */ + { PCI_VENDOR_ID_INTEL, 0x2683, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ESB2 */ + { PCI_VENDOR_ID_INTEL, 0x27c6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH7-M DH */ + { PCI_VENDOR_ID_INTEL, 0x2821, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH8 */ + { PCI_VENDOR_ID_INTEL, 0x2822, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH8 */ + { PCI_VENDOR_ID_INTEL, 0x2824, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH8 */ + { PCI_VENDOR_ID_INTEL, 0x2829, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH8M */ + { PCI_VENDOR_ID_INTEL, 0x282a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ICH8M */ + + /* JMicron */ + { 0x197b, 0x2360, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* JMicron JMB360 */ + { 0x197b, 0x2361, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* JMicron JMB361 */ + { 0x197b, 0x2363, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* JMicron JMB363 */ + { 0x197b, 0x2365, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* JMicron JMB365 */ + { 0x197b, 0x2366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* JMicron JMB366 */ + + /* ATI */ + { PCI_VENDOR_ID_ATI, 0x4380, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ATI SB600 non-raid */ + { PCI_VENDOR_ID_ATI, 0x4381, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* ATI SB600 raid */ + + /* VIA */ + { PCI_VENDOR_ID_VIA, 0x3349, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci_vt8251 }, /* VIA VT8251 */ + + /* NVIDIA */ + { PCI_VENDOR_ID_NVIDIA, 0x044c, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* MCP65 */ + { PCI_VENDOR_ID_NVIDIA, 0x044d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* MCP65 */ + { PCI_VENDOR_ID_NVIDIA, 0x044e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* MCP65 */ + { PCI_VENDOR_ID_NVIDIA, 0x044f, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* MCP65 */ + + /* SiS */ + { PCI_VENDOR_ID_SI, 0x1184, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* SiS 966 */ + { PCI_VENDOR_ID_SI, 0x1185, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* SiS 966 */ + { PCI_VENDOR_ID_SI, 0x0186, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_ahci }, /* SiS 968 */ + + { } /* terminate list */ +}; + + +static struct pci_driver ahci_pci_driver = { + .name = DRV_NAME, + .id_table = ahci_pci_tbl, + .probe = ahci_init_one, + .suspend = ahci_pci_device_suspend, + .resume = ahci_pci_device_resume, + .remove = ahci_remove_one, +}; + + +static inline unsigned long ahci_port_base_ul (unsigned long base, unsigned int port) +{ + return base + 0x100 + (port * 0x80); +} + +static inline void __iomem *ahci_port_base (void __iomem *base, unsigned int port) +{ + return (void __iomem *) ahci_port_base_ul((unsigned long)base, port); +} + +static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg_in) +{ + unsigned int sc_reg; + + switch (sc_reg_in) { + case SCR_STATUS: sc_reg = 0; break; + case SCR_CONTROL: sc_reg = 1; break; + case SCR_ERROR: sc_reg = 2; break; + case SCR_ACTIVE: sc_reg = 3; break; + default: + return 0xffffffffU; + } + + return readl((void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + + +static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg_in, + u32 val) +{ + unsigned int sc_reg; + + switch (sc_reg_in) { + case SCR_STATUS: sc_reg = 0; break; + case SCR_CONTROL: sc_reg = 1; break; + case SCR_ERROR: sc_reg = 2; break; + case SCR_ACTIVE: sc_reg = 3; break; + default: + return; + } + + writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + +static void ahci_start_engine(void __iomem *port_mmio) +{ + u32 tmp; + + /* start DMA */ + tmp = readl(port_mmio + PORT_CMD); + tmp |= PORT_CMD_START; + writel(tmp, port_mmio + PORT_CMD); + readl(port_mmio + PORT_CMD); /* flush */ +} + +static int ahci_stop_engine(void __iomem *port_mmio) +{ + u32 tmp; + + tmp = readl(port_mmio + PORT_CMD); + + /* check if the HBA is idle */ + if ((tmp & (PORT_CMD_START | PORT_CMD_LIST_ON)) == 0) + return 0; + + /* setting HBA to idle */ + tmp &= ~PORT_CMD_START; + writel(tmp, port_mmio + PORT_CMD); + + /* wait for engine to stop. This could be as long as 500 msec */ + tmp = ata_wait_register(port_mmio + PORT_CMD, + PORT_CMD_LIST_ON, PORT_CMD_LIST_ON, 1, 500); + if (tmp & PORT_CMD_LIST_ON) + return -EIO; + + return 0; +} + +static void ahci_start_fis_rx(void __iomem *port_mmio, u32 cap, + dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma) +{ + u32 tmp; + + /* set FIS registers */ + if (cap & HOST_CAP_64) + writel((cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI); + writel(cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR); + + if (cap & HOST_CAP_64) + writel((rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI); + writel(rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR); + + /* enable FIS reception */ + tmp = readl(port_mmio + PORT_CMD); + tmp |= PORT_CMD_FIS_RX; + writel(tmp, port_mmio + PORT_CMD); + + /* flush */ + readl(port_mmio + PORT_CMD); +} + +static int ahci_stop_fis_rx(void __iomem *port_mmio) +{ + u32 tmp; + + /* disable FIS reception */ + tmp = readl(port_mmio + PORT_CMD); + tmp &= ~PORT_CMD_FIS_RX; + writel(tmp, port_mmio + PORT_CMD); + + /* wait for completion, spec says 500ms, give it 1000 */ + tmp = ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_FIS_ON, + PORT_CMD_FIS_ON, 10, 1000); + if (tmp & PORT_CMD_FIS_ON) + return -EBUSY; + + return 0; +} + +static void ahci_power_up(void __iomem *port_mmio, u32 cap) +{ + u32 cmd; + + cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK; + + /* spin up device */ + if (cap & HOST_CAP_SSS) { + cmd |= PORT_CMD_SPIN_UP; + writel(cmd, port_mmio + PORT_CMD); + } + + /* wake up link */ + writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD); +} + +static void ahci_power_down(void __iomem *port_mmio, u32 cap) +{ + u32 cmd, scontrol; + + cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK; + + if (cap & HOST_CAP_SSC) { + /* enable transitions to slumber mode */ + scontrol = readl(port_mmio + PORT_SCR_CTL); + if ((scontrol & 0x0f00) > 0x100) { + scontrol &= ~0xf00; + writel(scontrol, port_mmio + PORT_SCR_CTL); + } + + /* put device into slumber mode */ + writel(cmd | PORT_CMD_ICC_SLUMBER, port_mmio + PORT_CMD); + + /* wait for the transition to complete */ + ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_ICC_SLUMBER, + PORT_CMD_ICC_SLUMBER, 1, 50); + } + + /* put device into listen mode */ + if (cap & HOST_CAP_SSS) { + /* first set PxSCTL.DET to 0 */ + scontrol = readl(port_mmio + PORT_SCR_CTL); + scontrol &= ~0xf; + writel(scontrol, port_mmio + PORT_SCR_CTL); + + /* then set PxCMD.SUD to 0 */ + cmd &= ~PORT_CMD_SPIN_UP; + writel(cmd, port_mmio + PORT_CMD); + } +} + +static void ahci_init_port(void __iomem *port_mmio, u32 cap, + dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma) +{ + /* power up */ + ahci_power_up(port_mmio, cap); + + /* enable FIS reception */ + ahci_start_fis_rx(port_mmio, cap, cmd_slot_dma, rx_fis_dma); + + /* enable DMA */ + ahci_start_engine(port_mmio); +} + +static int ahci_deinit_port(void __iomem *port_mmio, u32 cap, const char **emsg) +{ + int rc; + + /* disable DMA */ + rc = ahci_stop_engine(port_mmio); + if (rc) { + *emsg = "failed to stop engine"; + return rc; + } + + /* disable FIS reception */ + rc = ahci_stop_fis_rx(port_mmio); + if (rc) { + *emsg = "failed stop FIS RX"; + return rc; + } + + /* put device into slumber mode */ + ahci_power_down(port_mmio, cap); + + return 0; +} + +static int ahci_reset_controller(void __iomem *mmio, struct pci_dev *pdev) +{ + u32 cap_save, tmp; + + cap_save = readl(mmio + HOST_CAP); + cap_save &= ( (1<<28) | (1<<17) ); + cap_save |= (1 << 27); + + /* global controller reset */ + tmp = readl(mmio + HOST_CTL); + if ((tmp & HOST_RESET) == 0) { + writel(tmp | HOST_RESET, mmio + HOST_CTL); + readl(mmio + HOST_CTL); /* flush */ + } + + /* reset must complete within 1 second, or + * the hardware should be considered fried. + */ + ssleep(1); + + tmp = readl(mmio + HOST_CTL); + if (tmp & HOST_RESET) { + dev_printk(KERN_ERR, &pdev->dev, + "controller reset failed (0x%x)\n", tmp); + return -EIO; + } + + writel(HOST_AHCI_EN, mmio + HOST_CTL); + (void) readl(mmio + HOST_CTL); /* flush */ + writel(cap_save, mmio + HOST_CAP); + writel(0xf, mmio + HOST_PORTS_IMPL); + (void) readl(mmio + HOST_PORTS_IMPL); /* flush */ + + if (pdev->vendor == PCI_VENDOR_ID_INTEL) { + u16 tmp16; + + /* configure PCS */ + pci_read_config_word(pdev, 0x92, &tmp16); + tmp16 |= 0xf; + pci_write_config_word(pdev, 0x92, tmp16); + } + + return 0; +} + +static void ahci_init_controller(void __iomem *mmio, struct pci_dev *pdev, + int n_ports, u32 cap) +{ + int i, rc; + u32 tmp; + + for (i = 0; i < n_ports; i++) { + void __iomem *port_mmio = ahci_port_base(mmio, i); + const char *emsg = NULL; + +#if 0 /* BIOSen initialize this incorrectly */ + if (!(hpriv->port_map & (1 << i))) + continue; +#endif + + /* make sure port is not active */ + rc = ahci_deinit_port(port_mmio, cap, &emsg); + if (rc) + dev_printk(KERN_WARNING, &pdev->dev, + "%s (%d)\n", emsg, rc); + + /* clear SError */ + tmp = readl(port_mmio + PORT_SCR_ERR); + VPRINTK("PORT_SCR_ERR 0x%x\n", tmp); + writel(tmp, port_mmio + PORT_SCR_ERR); + + /* clear port IRQ */ + tmp = readl(port_mmio + PORT_IRQ_STAT); + VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp); + if (tmp) + writel(tmp, port_mmio + PORT_IRQ_STAT); + + writel(1 << i, mmio + HOST_IRQ_STAT); + } + + tmp = readl(mmio + HOST_CTL); + VPRINTK("HOST_CTL 0x%x\n", tmp); + writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL); + tmp = readl(mmio + HOST_CTL); + VPRINTK("HOST_CTL 0x%x\n", tmp); +} + +static unsigned int ahci_dev_classify(struct ata_port *ap) +{ + void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr; + struct ata_taskfile tf; + u32 tmp; + + tmp = readl(port_mmio + PORT_SIG); + tf.lbah = (tmp >> 24) & 0xff; + tf.lbam = (tmp >> 16) & 0xff; + tf.lbal = (tmp >> 8) & 0xff; + tf.nsect = (tmp) & 0xff; + + return ata_dev_classify(&tf); +} + +static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag, + u32 opts) +{ + dma_addr_t cmd_tbl_dma; + + cmd_tbl_dma = pp->cmd_tbl_dma + tag * AHCI_CMD_TBL_SZ; + + pp->cmd_slot[tag].opts = cpu_to_le32(opts); + pp->cmd_slot[tag].status = 0; + pp->cmd_slot[tag].tbl_addr = cpu_to_le32(cmd_tbl_dma & 0xffffffff); + pp->cmd_slot[tag].tbl_addr_hi = cpu_to_le32((cmd_tbl_dma >> 16) >> 16); +} + +static int ahci_clo(struct ata_port *ap) +{ + void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr; + struct ahci_host_priv *hpriv = ap->host->private_data; + u32 tmp; + + if (!(hpriv->cap & HOST_CAP_CLO)) + return -EOPNOTSUPP; + + tmp = readl(port_mmio + PORT_CMD); + tmp |= PORT_CMD_CLO; + writel(tmp, port_mmio + PORT_CMD); + + tmp = ata_wait_register(port_mmio + PORT_CMD, + PORT_CMD_CLO, PORT_CMD_CLO, 1, 500); + if (tmp & PORT_CMD_CLO) + return -EIO; + + return 0; +} + +static int ahci_prereset(struct ata_port *ap) +{ + if ((ap->flags & AHCI_FLAG_RESET_NEEDS_CLO) && + (ata_busy_wait(ap, ATA_BUSY, 1000) & ATA_BUSY)) { + /* ATA_BUSY hasn't cleared, so send a CLO */ + ahci_clo(ap); + } + + return ata_std_prereset(ap); +} + +static int ahci_softreset(struct ata_port *ap, unsigned int *class) +{ + struct ahci_port_priv *pp = ap->private_data; + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + const u32 cmd_fis_len = 5; /* five dwords */ + const char *reason = NULL; + struct ata_taskfile tf; + u32 tmp; + u8 *fis; + int rc; + + DPRINTK("ENTER\n"); + + if (ata_port_offline(ap)) { + DPRINTK("PHY reports no device\n"); + *class = ATA_DEV_NONE; + return 0; + } + + /* prepare for SRST (AHCI-1.1 10.4.1) */ + rc = ahci_stop_engine(port_mmio); + if (rc) { + reason = "failed to stop engine"; + goto fail_restart; + } + + /* check BUSY/DRQ, perform Command List Override if necessary */ + ahci_tf_read(ap, &tf); + if (tf.command & (ATA_BUSY | ATA_DRQ)) { + rc = ahci_clo(ap); + + if (rc == -EOPNOTSUPP) { + reason = "port busy but CLO unavailable"; + goto fail_restart; + } else if (rc) { + reason = "port busy but CLO failed"; + goto fail_restart; + } + } + + /* restart engine */ + ahci_start_engine(port_mmio); + + ata_tf_init(ap->device, &tf); + fis = pp->cmd_tbl; + + /* issue the first D2H Register FIS */ + ahci_fill_cmd_slot(pp, 0, + cmd_fis_len | AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY); + + tf.ctl |= ATA_SRST; + ata_tf_to_fis(&tf, fis, 0); + fis[1] &= ~(1 << 7); /* turn off Command FIS bit */ + + writel(1, port_mmio + PORT_CMD_ISSUE); + + tmp = ata_wait_register(port_mmio + PORT_CMD_ISSUE, 0x1, 0x1, 1, 500); + if (tmp & 0x1) { + rc = -EIO; + reason = "1st FIS failed"; + goto fail; + } + + /* spec says at least 5us, but be generous and sleep for 1ms */ + msleep(1); + + /* issue the second D2H Register FIS */ + ahci_fill_cmd_slot(pp, 0, cmd_fis_len); + + tf.ctl &= ~ATA_SRST; + ata_tf_to_fis(&tf, fis, 0); + fis[1] &= ~(1 << 7); /* turn off Command FIS bit */ + + writel(1, port_mmio + PORT_CMD_ISSUE); + readl(port_mmio + PORT_CMD_ISSUE); /* flush */ + + /* spec mandates ">= 2ms" before checking status. + * We wait 150ms, because that was the magic delay used for + * ATAPI devices in Hale Landis's ATADRVR, for the period of time + * between when the ATA command register is written, and then + * status is checked. Because waiting for "a while" before + * checking status is fine, post SRST, we perform this magic + * delay here as well. + */ + msleep(150); + + *class = ATA_DEV_NONE; + if (ata_port_online(ap)) { + if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) { + rc = -EIO; + reason = "device not ready"; + goto fail; + } + *class = ahci_dev_classify(ap); + } + + DPRINTK("EXIT, class=%u\n", *class); + return 0; + + fail_restart: + ahci_start_engine(port_mmio); + fail: + ata_port_printk(ap, KERN_ERR, "softreset failed (%s)\n", reason); + return rc; +} + +static int ahci_hardreset(struct ata_port *ap, unsigned int *class) +{ + struct ahci_port_priv *pp = ap->private_data; + u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG; + struct ata_taskfile tf; + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + int rc; + + DPRINTK("ENTER\n"); + + ahci_stop_engine(port_mmio); + + /* clear D2H reception area to properly wait for D2H FIS */ + ata_tf_init(ap->device, &tf); + tf.command = 0xff; + ata_tf_to_fis(&tf, d2h_fis, 0); + + rc = sata_std_hardreset(ap, class); + + ahci_start_engine(port_mmio); + + if (rc == 0 && ata_port_online(ap)) + *class = ahci_dev_classify(ap); + if (*class == ATA_DEV_UNKNOWN) + *class = ATA_DEV_NONE; + + DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class); + return rc; +} + +static void ahci_postreset(struct ata_port *ap, unsigned int *class) +{ + void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr; + u32 new_tmp, tmp; + + ata_std_postreset(ap, class); + + /* Make sure port's ATAPI bit is set appropriately */ + new_tmp = tmp = readl(port_mmio + PORT_CMD); + if (*class == ATA_DEV_ATAPI) + new_tmp |= PORT_CMD_ATAPI; + else + new_tmp &= ~PORT_CMD_ATAPI; + if (new_tmp != tmp) { + writel(new_tmp, port_mmio + PORT_CMD); + readl(port_mmio + PORT_CMD); /* flush */ + } +} + +static u8 ahci_check_status(struct ata_port *ap) +{ + void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr; + + return readl(mmio + PORT_TFDATA) & 0xFF; +} + +static void ahci_tf_read(struct ata_port *ap, struct ata_taskfile *tf) +{ + struct ahci_port_priv *pp = ap->private_data; + u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG; + + ata_tf_from_fis(d2h_fis, tf); +} + +static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc, void *cmd_tbl) +{ + struct scatterlist *sg; + struct ahci_sg *ahci_sg; + unsigned int n_sg = 0; + + VPRINTK("ENTER\n"); + + /* + * Next, the S/G list. + */ + ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ; + ata_for_each_sg(sg, qc) { + dma_addr_t addr = sg_dma_address(sg); + u32 sg_len = sg_dma_len(sg); + + ahci_sg->addr = cpu_to_le32(addr & 0xffffffff); + ahci_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16); + ahci_sg->flags_size = cpu_to_le32(sg_len - 1); + + ahci_sg++; + n_sg++; + } + + return n_sg; +} + +static void ahci_qc_prep(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ahci_port_priv *pp = ap->private_data; + int is_atapi = is_atapi_taskfile(&qc->tf); + void *cmd_tbl; + u32 opts; + const u32 cmd_fis_len = 5; /* five dwords */ + unsigned int n_elem; + + /* + * Fill in command table information. First, the header, + * a SATA Register - Host to Device command FIS. + */ + cmd_tbl = pp->cmd_tbl + qc->tag * AHCI_CMD_TBL_SZ; + + ata_tf_to_fis(&qc->tf, cmd_tbl, 0); + if (is_atapi) { + memset(cmd_tbl + AHCI_CMD_TBL_CDB, 0, 32); + memcpy(cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb, qc->dev->cdb_len); + } + + n_elem = 0; + if (qc->flags & ATA_QCFLAG_DMAMAP) + n_elem = ahci_fill_sg(qc, cmd_tbl); + + /* + * Fill in command slot information. + */ + opts = cmd_fis_len | n_elem << 16; + if (qc->tf.flags & ATA_TFLAG_WRITE) + opts |= AHCI_CMD_WRITE; + if (is_atapi) + opts |= AHCI_CMD_ATAPI | AHCI_CMD_PREFETCH; + + ahci_fill_cmd_slot(pp, qc->tag, opts); +} + +static void ahci_error_intr(struct ata_port *ap, u32 irq_stat) +{ + struct ahci_port_priv *pp = ap->private_data; + struct ata_eh_info *ehi = &ap->eh_info; + unsigned int err_mask = 0, action = 0; + struct ata_queued_cmd *qc; + u32 serror; + + ata_ehi_clear_desc(ehi); + + /* AHCI needs SError cleared; otherwise, it might lock up */ + serror = ahci_scr_read(ap, SCR_ERROR); + ahci_scr_write(ap, SCR_ERROR, serror); + + /* analyze @irq_stat */ + ata_ehi_push_desc(ehi, "irq_stat 0x%08x", irq_stat); + + if (irq_stat & PORT_IRQ_TF_ERR) + err_mask |= AC_ERR_DEV; + + if (irq_stat & (PORT_IRQ_HBUS_ERR | PORT_IRQ_HBUS_DATA_ERR)) { + err_mask |= AC_ERR_HOST_BUS; + action |= ATA_EH_SOFTRESET; + } + + if (irq_stat & PORT_IRQ_IF_ERR) { + err_mask |= AC_ERR_ATA_BUS; + action |= ATA_EH_SOFTRESET; + ata_ehi_push_desc(ehi, ", interface fatal error"); + } + + if (irq_stat & (PORT_IRQ_CONNECT | PORT_IRQ_PHYRDY)) { + ata_ehi_hotplugged(ehi); + ata_ehi_push_desc(ehi, ", %s", irq_stat & PORT_IRQ_CONNECT ? + "connection status changed" : "PHY RDY changed"); + } + + if (irq_stat & PORT_IRQ_UNK_FIS) { + u32 *unk = (u32 *)(pp->rx_fis + RX_FIS_UNK); + + err_mask |= AC_ERR_HSM; + action |= ATA_EH_SOFTRESET; + ata_ehi_push_desc(ehi, ", unknown FIS %08x %08x %08x %08x", + unk[0], unk[1], unk[2], unk[3]); + } + + /* okay, let's hand over to EH */ + ehi->serror |= serror; + ehi->action |= action; + + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc) + qc->err_mask |= err_mask; + else + ehi->err_mask |= err_mask; + + if (irq_stat & PORT_IRQ_FREEZE) + ata_port_freeze(ap); + else + ata_port_abort(ap); +} + +static void ahci_host_intr(struct ata_port *ap) +{ + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + struct ata_eh_info *ehi = &ap->eh_info; + u32 status, qc_active; + int rc; + + status = readl(port_mmio + PORT_IRQ_STAT); + writel(status, port_mmio + PORT_IRQ_STAT); + + if (unlikely(status & PORT_IRQ_ERROR)) { + ahci_error_intr(ap, status); + return; + } + + if (ap->sactive) + qc_active = readl(port_mmio + PORT_SCR_ACT); + else + qc_active = readl(port_mmio + PORT_CMD_ISSUE); + + rc = ata_qc_complete_multiple(ap, qc_active, NULL); + if (rc > 0) + return; + if (rc < 0) { + ehi->err_mask |= AC_ERR_HSM; + ehi->action |= ATA_EH_SOFTRESET; + ata_port_freeze(ap); + return; + } + + /* hmmm... a spurious interupt */ + + /* some devices send D2H reg with I bit set during NCQ command phase */ + if (ap->sactive && status & PORT_IRQ_D2H_REG_FIS) + return; + + /* ignore interim PIO setup fis interrupts */ + if (ata_tag_valid(ap->active_tag) && (status & PORT_IRQ_PIOS_FIS)) + return; + + if (ata_ratelimit()) + ata_port_printk(ap, KERN_INFO, "spurious interrupt " + "(irq_stat 0x%x active_tag %d sactive 0x%x)\n", + status, ap->active_tag, ap->sactive); +} + +static void ahci_irq_clear(struct ata_port *ap) +{ + /* TODO */ +} + +static irqreturn_t ahci_interrupt(int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + struct ahci_host_priv *hpriv; + unsigned int i, handled = 0; + void __iomem *mmio; + u32 irq_stat, irq_ack = 0; + + VPRINTK("ENTER\n"); + + hpriv = host->private_data; + mmio = host->mmio_base; + + /* sigh. 0xffffffff is a valid return from h/w */ + irq_stat = readl(mmio + HOST_IRQ_STAT); + irq_stat &= hpriv->port_map; + if (!irq_stat) + return IRQ_NONE; + + spin_lock(&host->lock); + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap; + + if (!(irq_stat & (1 << i))) + continue; + + ap = host->ports[i]; + if (ap) { + ahci_host_intr(ap); + VPRINTK("port %u\n", i); + } else { + VPRINTK("port %u (no irq)\n", i); + if (ata_ratelimit()) + dev_printk(KERN_WARNING, host->dev, + "interrupt on disabled port %u\n", i); + } + + irq_ack |= (1 << i); + } + + if (irq_ack) { + writel(irq_ack, mmio + HOST_IRQ_STAT); + handled = 1; + } + + spin_unlock(&host->lock); + + VPRINTK("EXIT\n"); + + return IRQ_RETVAL(handled); +} + +static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr; + + if (qc->tf.protocol == ATA_PROT_NCQ) + writel(1 << qc->tag, port_mmio + PORT_SCR_ACT); + writel(1 << qc->tag, port_mmio + PORT_CMD_ISSUE); + readl(port_mmio + PORT_CMD_ISSUE); /* flush */ + + return 0; +} + +static void ahci_freeze(struct ata_port *ap) +{ + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + + /* turn IRQ off */ + writel(0, port_mmio + PORT_IRQ_MASK); +} + +static void ahci_thaw(struct ata_port *ap) +{ + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + u32 tmp; + + /* clear IRQ */ + tmp = readl(port_mmio + PORT_IRQ_STAT); + writel(tmp, port_mmio + PORT_IRQ_STAT); + writel(1 << ap->id, mmio + HOST_IRQ_STAT); + + /* turn IRQ back on */ + writel(DEF_PORT_IRQ, port_mmio + PORT_IRQ_MASK); +} + +static void ahci_error_handler(struct ata_port *ap) +{ + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + + if (!(ap->pflags & ATA_PFLAG_FROZEN)) { + /* restart engine */ + ahci_stop_engine(port_mmio); + ahci_start_engine(port_mmio); + } + + /* perform recovery */ + ata_do_eh(ap, ahci_prereset, ahci_softreset, ahci_hardreset, + ahci_postreset); +} + +static void ahci_post_internal_cmd(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + + if (qc->flags & ATA_QCFLAG_FAILED) + qc->err_mask |= AC_ERR_OTHER; + + if (qc->err_mask) { + /* make DMA engine forget about the failed command */ + ahci_stop_engine(port_mmio); + ahci_start_engine(port_mmio); + } +} + +static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg) +{ + struct ahci_host_priv *hpriv = ap->host->private_data; + struct ahci_port_priv *pp = ap->private_data; + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + const char *emsg = NULL; + int rc; + + rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg); + if (rc) { + ata_port_printk(ap, KERN_ERR, "%s (%d)\n", emsg, rc); + ahci_init_port(port_mmio, hpriv->cap, + pp->cmd_slot_dma, pp->rx_fis_dma); + } + + return rc; +} + +static int ahci_port_resume(struct ata_port *ap) +{ + struct ahci_port_priv *pp = ap->private_data; + struct ahci_host_priv *hpriv = ap->host->private_data; + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + + ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma); + + return 0; +} + +static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + void __iomem *mmio = host->mmio_base; + u32 ctl; + + if (mesg.event == PM_EVENT_SUSPEND) { + /* AHCI spec rev1.1 section 8.3.3: + * Software must disable interrupts prior to requesting a + * transition of the HBA to D3 state. + */ + ctl = readl(mmio + HOST_CTL); + ctl &= ~HOST_IRQ_EN; + writel(ctl, mmio + HOST_CTL); + readl(mmio + HOST_CTL); /* flush */ + } + + return ata_pci_device_suspend(pdev, mesg); +} + +static int ahci_pci_device_resume(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + struct ahci_host_priv *hpriv = host->private_data; + void __iomem *mmio = host->mmio_base; + int rc; + + ata_pci_device_do_resume(pdev); + + if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) { + rc = ahci_reset_controller(mmio, pdev); + if (rc) + return rc; + + ahci_init_controller(mmio, pdev, host->n_ports, hpriv->cap); + } + + ata_host_resume(host); + + return 0; +} + +static int ahci_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct ahci_host_priv *hpriv = ap->host->private_data; + struct ahci_port_priv *pp; + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + void *mem; + dma_addr_t mem_dma; + int rc; + + pp = kmalloc(sizeof(*pp), GFP_KERNEL); + if (!pp) + return -ENOMEM; + memset(pp, 0, sizeof(*pp)); + + rc = ata_pad_alloc(ap, dev); + if (rc) { + kfree(pp); + return rc; + } + + mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL); + if (!mem) { + ata_pad_free(ap, dev); + kfree(pp); + return -ENOMEM; + } + memset(mem, 0, AHCI_PORT_PRIV_DMA_SZ); + + /* + * First item in chunk of DMA memory: 32-slot command table, + * 32 bytes each in size + */ + pp->cmd_slot = mem; + pp->cmd_slot_dma = mem_dma; + + mem += AHCI_CMD_SLOT_SZ; + mem_dma += AHCI_CMD_SLOT_SZ; + + /* + * Second item: Received-FIS area + */ + pp->rx_fis = mem; + pp->rx_fis_dma = mem_dma; + + mem += AHCI_RX_FIS_SZ; + mem_dma += AHCI_RX_FIS_SZ; + + /* + * Third item: data area for storing a single command + * and its scatter-gather table + */ + pp->cmd_tbl = mem; + pp->cmd_tbl_dma = mem_dma; + + ap->private_data = pp; + + /* initialize port */ + ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma); + + return 0; +} + +static void ahci_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct ahci_host_priv *hpriv = ap->host->private_data; + struct ahci_port_priv *pp = ap->private_data; + void __iomem *mmio = ap->host->mmio_base; + void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no); + const char *emsg = NULL; + int rc; + + /* de-initialize port */ + rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg); + if (rc) + ata_port_printk(ap, KERN_WARNING, "%s (%d)\n", emsg, rc); + + ap->private_data = NULL; + dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, + pp->cmd_slot, pp->cmd_slot_dma); + ata_pad_free(ap, dev); + kfree(pp); +} + +static void ahci_setup_port(struct ata_ioports *port, unsigned long base, + unsigned int port_idx) +{ + VPRINTK("ENTER, base==0x%lx, port_idx %u\n", base, port_idx); + base = ahci_port_base_ul(base, port_idx); + VPRINTK("base now==0x%lx\n", base); + + port->cmd_addr = base; + port->scr_addr = base + PORT_SCR; + + VPRINTK("EXIT\n"); +} + +static int ahci_host_init(struct ata_probe_ent *probe_ent) +{ + struct ahci_host_priv *hpriv = probe_ent->private_data; + struct pci_dev *pdev = to_pci_dev(probe_ent->dev); + void __iomem *mmio = probe_ent->mmio_base; + unsigned int i, using_dac; + int rc; + + rc = ahci_reset_controller(mmio, pdev); + if (rc) + return rc; + + hpriv->cap = readl(mmio + HOST_CAP); + hpriv->port_map = readl(mmio + HOST_PORTS_IMPL); + probe_ent->n_ports = (hpriv->cap & 0x1f) + 1; + + VPRINTK("cap 0x%x port_map 0x%x n_ports %d\n", + hpriv->cap, hpriv->port_map, probe_ent->n_ports); + + using_dac = hpriv->cap & HOST_CAP_64; + if (using_dac && + !pci_set_dma_mask(pdev, DMA_64BIT_MASK)) { + rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK); + if (rc) { + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "64-bit DMA enable failed\n"); + return rc; + } + } + } else { + rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit DMA enable failed\n"); + return rc; + } + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit consistent DMA enable failed\n"); + return rc; + } + } + + for (i = 0; i < probe_ent->n_ports; i++) + ahci_setup_port(&probe_ent->port[i], (unsigned long) mmio, i); + + ahci_init_controller(mmio, pdev, probe_ent->n_ports, hpriv->cap); + + pci_set_master(pdev); + + return 0; +} + +static void ahci_print_info(struct ata_probe_ent *probe_ent) +{ + struct ahci_host_priv *hpriv = probe_ent->private_data; + struct pci_dev *pdev = to_pci_dev(probe_ent->dev); + void __iomem *mmio = probe_ent->mmio_base; + u32 vers, cap, impl, speed; + const char *speed_s; + u16 cc; + const char *scc_s; + + vers = readl(mmio + HOST_VERSION); + cap = hpriv->cap; + impl = hpriv->port_map; + + speed = (cap >> 20) & 0xf; + if (speed == 1) + speed_s = "1.5"; + else if (speed == 2) + speed_s = "3"; + else + speed_s = "?"; + + pci_read_config_word(pdev, 0x0a, &cc); + if (cc == 0x0101) + scc_s = "IDE"; + else if (cc == 0x0106) + scc_s = "SATA"; + else if (cc == 0x0104) + scc_s = "RAID"; + else + scc_s = "unknown"; + + dev_printk(KERN_INFO, &pdev->dev, + "AHCI %02x%02x.%02x%02x " + "%u slots %u ports %s Gbps 0x%x impl %s mode\n" + , + + (vers >> 24) & 0xff, + (vers >> 16) & 0xff, + (vers >> 8) & 0xff, + vers & 0xff, + + ((cap >> 8) & 0x1f) + 1, + (cap & 0x1f) + 1, + speed_s, + impl, + scc_s); + + dev_printk(KERN_INFO, &pdev->dev, + "flags: " + "%s%s%s%s%s%s" + "%s%s%s%s%s%s%s\n" + , + + cap & (1 << 31) ? "64bit " : "", + cap & (1 << 30) ? "ncq " : "", + cap & (1 << 28) ? "ilck " : "", + cap & (1 << 27) ? "stag " : "", + cap & (1 << 26) ? "pm " : "", + cap & (1 << 25) ? "led " : "", + + cap & (1 << 24) ? "clo " : "", + cap & (1 << 19) ? "nz " : "", + cap & (1 << 18) ? "only " : "", + cap & (1 << 17) ? "pmp " : "", + cap & (1 << 15) ? "pio " : "", + cap & (1 << 14) ? "slum " : "", + cap & (1 << 13) ? "part " : "" + ); +} + +static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + struct ahci_host_priv *hpriv; + unsigned long base; + void __iomem *mmio_base; + unsigned int board_idx = (unsigned int) ent->driver_data; + int have_msi, pci_dev_busy = 0; + int rc; + + VPRINTK("ENTER\n"); + + WARN_ON(ATA_MAX_QUEUE > AHCI_MAX_CMDS); + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + /* JMicron-specific fixup: make sure we're in AHCI mode */ + /* This is protected from races with ata_jmicron by the pci probe + locking */ + if (pdev->vendor == PCI_VENDOR_ID_JMICRON) { + /* AHCI enable, AHCI on function 0 */ + pci_write_config_byte(pdev, 0x41, 0xa1); + /* Function 1 is the PATA controller */ + if (PCI_FUNC(pdev->devfn)) + return -ENODEV; + } + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + if (pci_enable_msi(pdev) == 0) + have_msi = 1; + else { + pci_intx(pdev, 1); + have_msi = 0; + } + + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_msi; + } + + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, AHCI_PCI_BAR, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + base = (unsigned long) mmio_base; + + hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL); + if (!hpriv) { + rc = -ENOMEM; + goto err_out_iounmap; + } + memset(hpriv, 0, sizeof(*hpriv)); + + probe_ent->sht = ahci_port_info[board_idx].sht; + probe_ent->port_flags = ahci_port_info[board_idx].flags; + probe_ent->pio_mask = ahci_port_info[board_idx].pio_mask; + probe_ent->udma_mask = ahci_port_info[board_idx].udma_mask; + probe_ent->port_ops = ahci_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + probe_ent->private_data = hpriv; + + if (have_msi) + hpriv->flags |= AHCI_FLAG_MSI; + + /* initialize adapter */ + rc = ahci_host_init(probe_ent); + if (rc) + goto err_out_hpriv; + + if (!(probe_ent->port_flags & AHCI_FLAG_NO_NCQ) && + (hpriv->cap & HOST_CAP_NCQ)) + probe_ent->port_flags |= ATA_FLAG_NCQ; + + ahci_print_info(probe_ent); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_hpriv: + kfree(hpriv); +err_out_iounmap: + pci_iounmap(pdev, mmio_base); +err_out_free_ent: + kfree(probe_ent); +err_out_msi: + if (have_msi) + pci_disable_msi(pdev); + else + pci_intx(pdev, 0); + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; +} + +static void ahci_remove_one (struct pci_dev *pdev) +{ + struct device *dev = pci_dev_to_dev(pdev); + struct ata_host *host = dev_get_drvdata(dev); + struct ahci_host_priv *hpriv = host->private_data; + unsigned int i; + int have_msi; + + for (i = 0; i < host->n_ports; i++) + ata_port_detach(host->ports[i]); + + have_msi = hpriv->flags & AHCI_FLAG_MSI; + free_irq(host->irq, host); + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + + ata_scsi_release(ap->scsi_host); + scsi_host_put(ap->scsi_host); + } + + kfree(hpriv); + pci_iounmap(pdev, host->mmio_base); + kfree(host); + + if (have_msi) + pci_disable_msi(pdev); + else + pci_intx(pdev, 0); + pci_release_regions(pdev); + pci_disable_device(pdev); + dev_set_drvdata(dev, NULL); +} + +static int __init ahci_init(void) +{ + return pci_register_driver(&ahci_pci_driver); +} + +static void __exit ahci_exit(void) +{ + pci_unregister_driver(&ahci_pci_driver); +} + + +MODULE_AUTHOR("Jeff Garzik"); +MODULE_DESCRIPTION("AHCI SATA low-level driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, ahci_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_init(ahci_init); +module_exit(ahci_exit); diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c new file mode 100644 index 00000000000..377425e7139 --- /dev/null +++ b/drivers/ata/ata_generic.c @@ -0,0 +1,252 @@ +/* + * ata_generic.c - Generic PATA/SATA controller driver. + * Copyright 2005 Red Hat Inc <alan@redhat.com>, all rights reserved. + * + * Elements from ide/pci/generic.c + * Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org> + * Portions (C) Copyright 2002 Red Hat Inc <alan@redhat.com> + * + * May be copied or modified under the terms of the GNU General Public License + * + * Driver for PCI IDE interfaces implementing the standard bus mastering + * interface functionality. This assumes the BIOS did the drive set up and + * tuning for us. By default we do not grab all IDE class devices as they + * may have other drivers or need fixups to avoid problems. Instead we keep + * a default list of stuff without documentation/driver that appears to + * work. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "ata_generic" +#define DRV_VERSION "0.2.6" + +/* + * A generic parallel ATA driver using libata + */ + +/** + * generic_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int generic_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + + +/** + * generic_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * @classes: + * + * LOCKING: + * None (inherited from caller). + */ + + +static void generic_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, generic_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * generic_set_mode - mode setting + * @ap: interface to set up + * + * Use a non standard set_mode function. We don't want to be tuned. + * The BIOS configured everything. Our job is not to fiddle. We + * read the dma enabled bits from the PCI configuration of the device + * and respect them. + */ + +static void generic_set_mode(struct ata_port *ap) +{ + int dma_enabled = 0; + int i; + + /* Bits 5 and 6 indicate if DMA is active on master/slave */ + if (ap->ioaddr.bmdma_addr) + dma_enabled = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + if (ata_dev_enabled(dev)) { + /* We don't really care */ + dev->pio_mode = XFER_PIO_0; + dev->dma_mode = XFER_MW_DMA_0; + /* We do need the right mode information for DMA or PIO + and this comes from the current configuration flags */ + if (dma_enabled & (1 << (5 + i))) { + dev->xfer_mode = XFER_MW_DMA_0; + dev->xfer_shift = ATA_SHIFT_MWDMA; + dev->flags &= ~ATA_DFLAG_PIO; + } else { + dev->xfer_mode = XFER_PIO_0; + dev->xfer_shift = ATA_SHIFT_PIO; + dev->flags |= ATA_DFLAG_PIO; + } + } + } +} + +static struct scsi_host_template generic_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations generic_port_ops = { + .set_mode = generic_set_mode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = generic_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int all_generic_ide; /* Set to claim all devices */ + +/** + * ata_generic_init - attach generic IDE + * @dev: PCI device found + * @id: match entry + * + * Called each time a matching IDE interface is found. We check if the + * interface is one we wish to claim and if so we perform any chip + * specific hacks then let the ATA layer do the heavy lifting. + */ + +static int ata_generic_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + u16 command; + static struct ata_port_info info = { + .sht = &generic_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &generic_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + + /* Don't use the generic entry unless instructed to do so */ + if (id->driver_data == 1 && all_generic_ide == 0) + return -ENODEV; + + /* Devices that need care */ + if (dev->vendor == PCI_VENDOR_ID_UMC && + dev->device == PCI_DEVICE_ID_UMC_UM8886A && + (!(PCI_FUNC(dev->devfn) & 1))) + return -ENODEV; + + if (dev->vendor == PCI_VENDOR_ID_OPTI && + dev->device == PCI_DEVICE_ID_OPTI_82C558 && + (!(PCI_FUNC(dev->devfn) & 1))) + return -ENODEV; + + /* Don't re-enable devices in generic mode or we will break some + motherboards with disabled and unused IDE controllers */ + pci_read_config_word(dev, PCI_COMMAND, &command); + if (!(command & PCI_COMMAND_IO)) + return -ENODEV; + + if (dev->vendor == PCI_VENDOR_ID_AL) + ata_pci_clear_simplex(dev); + + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id ata_generic[] = { + { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_SAMURAI_IDE), }, + { PCI_DEVICE(PCI_VENDOR_ID_HOLTEK, PCI_DEVICE_ID_HOLTEK_6565), }, + { PCI_DEVICE(PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8673F), }, + { PCI_DEVICE(PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886A), }, + { PCI_DEVICE(PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF), }, + { PCI_DEVICE(PCI_VENDOR_ID_HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE), }, + { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C561), }, + { PCI_DEVICE(PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C558), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), }, + /* Must come last. If you add entries adjust this table appropriately */ + { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 1}, + { 0, }, +}; + +static struct pci_driver ata_generic_pci_driver = { + .name = DRV_NAME, + .id_table = ata_generic, + .probe = ata_generic_init_one, + .remove = ata_pci_remove_one +}; + +static int __init ata_generic_init(void) +{ + return pci_module_init(&ata_generic_pci_driver); +} + + +static void __exit ata_generic_exit(void) +{ + pci_unregister_driver(&ata_generic_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for generic ATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, ata_generic); +MODULE_VERSION(DRV_VERSION); + +module_init(ata_generic_init); +module_exit(ata_generic_exit); + +module_param(all_generic_ide, int, 0); diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c new file mode 100644 index 00000000000..5719704eb0e --- /dev/null +++ b/drivers/ata/ata_piix.c @@ -0,0 +1,1256 @@ +/* + * ata_piix.c - Intel PATA/SATA controllers + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * + * Copyright 2003-2005 Red Hat Inc + * Copyright 2003-2005 Jeff Garzik + * + * + * Copyright header from piix.c: + * + * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer + * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> + * Copyright (C) 2003 Red Hat Inc <alan@redhat.com> + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available at http://developer.intel.com/ + * + * Documentation + * Publically available from Intel web site. Errata documentation + * is also publically available. As an aide to anyone hacking on this + * driver the list of errata that are relevant is below.going back to + * PIIX4. Older device documentation is now a bit tricky to find. + * + * The chipsets all follow very much the same design. The orginal Triton + * series chipsets do _not_ support independant device timings, but this + * is fixed in Triton II. With the odd mobile exception the chips then + * change little except in gaining more modes until SATA arrives. This + * driver supports only the chips with independant timing (that is those + * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix + * for the early chip drivers. + * + * Errata of note: + * + * Unfixable + * PIIX4 errata #9 - Only on ultra obscure hw + * ICH3 errata #13 - Not observed to affect real hw + * by Intel + * + * Things we must deal with + * PIIX4 errata #10 - BM IDE hang with non UDMA + * (must stop/start dma to recover) + * 440MX errata #15 - As PIIX4 errata #10 + * PIIX4 errata #15 - Must not read control registers + * during a PIO transfer + * 440MX errata #13 - As PIIX4 errata #15 + * ICH2 errata #21 - DMA mode 0 doesn't work right + * ICH0/1 errata #55 - As ICH2 errata #21 + * ICH2 spec c #9 - Extra operations needed to handle + * drive hotswap [NOT YET SUPPORTED] + * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary + * and must be dword aligned + * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3 + * + * Should have been BIOS fixed: + * 450NX: errata #19 - DMA hangs on old 450NX + * 450NX: errata #20 - DMA hangs on old 450NX + * 450NX: errata #25 - Corruption with DMA on old 450NX + * ICH3 errata #15 - IDE deadlock under high load + * (BIOS must set dev 31 fn 0 bit 23) + * ICH3 errata #18 - Don't use native mode + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "ata_piix" +#define DRV_VERSION "2.00ac6" + +enum { + PIIX_IOCFG = 0x54, /* IDE I/O configuration register */ + ICH5_PMR = 0x90, /* port mapping register */ + ICH5_PCS = 0x92, /* port control and status */ + PIIX_SCC = 0x0A, /* sub-class code register */ + + PIIX_FLAG_IGNORE_PCS = (1 << 25), /* ignore PCS present bits */ + PIIX_FLAG_SCR = (1 << 26), /* SCR available */ + PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */ + PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */ + + /* combined mode. if set, PATA is channel 0. + * if clear, PATA is channel 1. + */ + PIIX_PORT_ENABLED = (1 << 0), + PIIX_PORT_PRESENT = (1 << 4), + + PIIX_80C_PRI = (1 << 5) | (1 << 4), + PIIX_80C_SEC = (1 << 7) | (1 << 6), + + /* controller IDs */ + piix_pata_33 = 0, /* PIIX3 or 4 at 33Mhz */ + ich_pata_33 = 1, /* ICH up to UDMA 33 only */ + ich_pata_66 = 2, /* ICH up to 66 Mhz */ + ich_pata_100 = 3, /* ICH up to UDMA 100 */ + ich_pata_133 = 4, /* ICH up to UDMA 133 */ + ich5_sata = 5, + esb_sata = 6, + ich6_sata = 7, + ich6_sata_ahci = 8, + ich6m_sata_ahci = 9, + ich7m_sata_ahci = 10, + ich8_sata_ahci = 11, + + /* constants for mapping table */ + P0 = 0, /* port 0 */ + P1 = 1, /* port 1 */ + P2 = 2, /* port 2 */ + P3 = 3, /* port 3 */ + IDE = -1, /* IDE */ + NA = -2, /* not avaliable */ + RV = -3, /* reserved */ + + PIIX_AHCI_DEVICE = 6, +}; + +struct piix_map_db { + const u32 mask; + const u16 port_enable; + const int present_shift; + const int map[][4]; +}; + +struct piix_host_priv { + const int *map; + const struct piix_map_db *map_db; +}; + +static int piix_init_one (struct pci_dev *pdev, + const struct pci_device_id *ent); +static void piix_host_stop(struct ata_host *host); +static void piix_pata_error_handler(struct ata_port *ap); +static void ich_pata_error_handler(struct ata_port *ap); +static void piix_sata_error_handler(struct ata_port *ap); +static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev); +static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev); +static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev); + +static unsigned int in_module_init = 1; + +static const struct pci_device_id piix_pci_tbl[] = { +#ifdef ATA_ENABLE_PATA + /* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */ + /* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */ + { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 }, + { 0x8086, 0x24db, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + { 0x8086, 0x25a2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* Intel PIIX4 */ + { 0x8086, 0x7199, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 }, + /* Intel PIIX4 */ + { 0x8086, 0x7601, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 }, + /* Intel PIIX */ + { 0x8086, 0x84CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 }, + /* Intel ICH (i810, i815, i840) UDMA 66*/ + { 0x8086, 0x2411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_66 }, + /* Intel ICH0 : UDMA 33*/ + { 0x8086, 0x2421, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_33 }, + /* Intel ICH2M */ + { 0x8086, 0x244A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* Intel ICH2 (i810E2, i845, 850, 860) UDMA 100 */ + { 0x8086, 0x244B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* Intel ICH3M */ + { 0x8086, 0x248A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* Intel ICH3 (E7500/1) UDMA 100 */ + { 0x8086, 0x248B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* Intel ICH4 (i845GV, i845E, i852, i855) UDMA 100 */ + { 0x8086, 0x24CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + { 0x8086, 0x24CB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* Intel ICH5 */ + { 0x8086, 0x24DB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 }, + /* C-ICH (i810E2) */ + { 0x8086, 0x245B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* ESB (855GME/875P + 6300ESB) UDMA 100 */ + { 0x8086, 0x25A2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* ICH6 (and 6) (i915) UDMA 100 */ + { 0x8086, 0x266F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, + /* ICH7/7-R (i945, i975) UDMA 100*/ + { 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_133 }, + { 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 }, +#endif + + /* NOTE: The following PCI ids must be kept in sync with the + * list in drivers/pci/quirks.c. + */ + + /* 82801EB (ICH5) */ + { 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata }, + /* 82801EB (ICH5) */ + { 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata }, + /* 6300ESB (ICH5 variant with broken PCS present bits) */ + { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata }, + /* 6300ESB pretending RAID */ + { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb_sata }, + /* 82801FB/FW (ICH6/ICH6W) */ + { 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata }, + /* 82801FR/FRW (ICH6R/ICH6RW) */ + { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci }, + /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented) */ + { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci }, + /* 82801GB/GR/GH (ICH7, identical to ICH6) */ + { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci }, + /* 2801GBM/GHM (ICH7M, identical to ICH6M) */ + { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich7m_sata_ahci }, + /* Enterprise Southbridge 2 (where's the datasheet?) */ + { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci }, + /* SATA Controller 1 IDE (ICH8, no datasheet yet) */ + { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci }, + /* SATA Controller 2 IDE (ICH8, ditto) */ + { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci }, + /* Mobile SATA Controller IDE (ICH8M, ditto) */ + { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci }, + + { } /* terminate list */ +}; + +static struct pci_driver piix_pci_driver = { + .name = DRV_NAME, + .id_table = piix_pci_tbl, + .probe = piix_init_one, + .remove = ata_pci_remove_one, + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +}; + +static struct scsi_host_template piix_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, + .resume = ata_scsi_device_resume, + .suspend = ata_scsi_device_suspend, +}; + +static const struct ata_port_operations piix_pata_ops = { + .port_disable = ata_port_disable, + .set_piomode = piix_set_piomode, + .set_dmamode = piix_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = piix_pata_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = piix_host_stop, +}; + +static const struct ata_port_operations ich_pata_ops = { + .port_disable = ata_port_disable, + .set_piomode = piix_set_piomode, + .set_dmamode = ich_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ich_pata_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations piix_sata_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = piix_sata_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = piix_host_stop, +}; + +static const struct piix_map_db ich5_map_db = { + .mask = 0x7, + .port_enable = 0x3, + .present_shift = 4, + .map = { + /* PM PS SM SS MAP */ + { P0, NA, P1, NA }, /* 000b */ + { P1, NA, P0, NA }, /* 001b */ + { RV, RV, RV, RV }, + { RV, RV, RV, RV }, + { P0, P1, IDE, IDE }, /* 100b */ + { P1, P0, IDE, IDE }, /* 101b */ + { IDE, IDE, P0, P1 }, /* 110b */ + { IDE, IDE, P1, P0 }, /* 111b */ + }, +}; + +static const struct piix_map_db ich6_map_db = { + .mask = 0x3, + .port_enable = 0xf, + .present_shift = 4, + .map = { + /* PM PS SM SS MAP */ + { P0, P2, P1, P3 }, /* 00b */ + { IDE, IDE, P1, P3 }, /* 01b */ + { P0, P2, IDE, IDE }, /* 10b */ + { RV, RV, RV, RV }, + }, +}; + +static const struct piix_map_db ich6m_map_db = { + .mask = 0x3, + .port_enable = 0x5, + .present_shift = 4, + .map = { + /* PM PS SM SS MAP */ + { P0, P2, RV, RV }, /* 00b */ + { RV, RV, RV, RV }, + { P0, P2, IDE, IDE }, /* 10b */ + { RV, RV, RV, RV }, + }, +}; + +static const struct piix_map_db ich7m_map_db = { + .mask = 0x3, + .port_enable = 0x5, + .present_shift = 4, + + /* Map 01b isn't specified in the doc but some notebooks use + * it anyway. ATM, the only case spotted carries subsystem ID + * 1025:0107. This is the only difference from ich6m. + */ + .map = { + /* PM PS SM SS MAP */ + { P0, P2, RV, RV }, /* 00b */ + { IDE, IDE, P1, P3 }, /* 01b */ + { P0, P2, IDE, IDE }, /* 10b */ + { RV, RV, RV, RV }, + }, +}; + +static const struct piix_map_db ich8_map_db = { + .mask = 0x3, + .port_enable = 0x3, + .present_shift = 8, + .map = { + /* PM PS SM SS MAP */ + { P0, NA, P1, NA }, /* 00b (hardwired) */ + { RV, RV, RV, RV }, + { RV, RV, RV, RV }, /* 10b (never) */ + { RV, RV, RV, RV }, + }, +}; + +static const struct piix_map_db *piix_map_db_table[] = { + [ich5_sata] = &ich5_map_db, + [esb_sata] = &ich5_map_db, + [ich6_sata] = &ich6_map_db, + [ich6_sata_ahci] = &ich6_map_db, + [ich6m_sata_ahci] = &ich6m_map_db, + [ich7m_sata_ahci] = &ich7m_map_db, + [ich8_sata_ahci] = &ich8_map_db, +}; + +static struct ata_port_info piix_port_info[] = { + /* piix_pata_33: 0: PIIX3 or 4 at 33MHz */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ + .udma_mask = ATA_UDMA_MASK_40C, + .port_ops = &piix_pata_ops, + }, + + /* ich_pata_33: 1 ICH0 - ICH at 33Mhz*/ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS, + .pio_mask = 0x1f, /* pio 0-4 */ + .mwdma_mask = 0x06, /* Check: maybe 0x07 */ + .udma_mask = ATA_UDMA2, /* UDMA33 */ + .port_ops = &ich_pata_ops, + }, + /* ich_pata_66: 2 ICH controllers up to 66MHz */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS, + .pio_mask = 0x1f, /* pio 0-4 */ + .mwdma_mask = 0x06, /* MWDMA0 is broken on chip */ + .udma_mask = ATA_UDMA4, + .port_ops = &ich_pata_ops, + }, + + /* ich_pata_100: 3 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x06, /* mwdma1-2 */ + .udma_mask = ATA_UDMA5, /* udma0-5 */ + .port_ops = &ich_pata_ops, + }, + + /* ich_pata_133: 4 ICH with full UDMA6 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR, + .pio_mask = 0x1f, /* pio 0-4 */ + .mwdma_mask = 0x06, /* Check: maybe 0x07 */ + .udma_mask = ATA_UDMA6, /* UDMA133 */ + .port_ops = &ich_pata_ops, + }, + + /* ich5_sata: 5 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR | + PIIX_FLAG_IGNORE_PCS, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &piix_sata_ops, + }, + + /* i6300esb_sata: 6 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SATA | + PIIX_FLAG_CHECKINTR | PIIX_FLAG_IGNORE_PCS, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &piix_sata_ops, + }, + + /* ich6_sata: 7 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SATA | + PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &piix_sata_ops, + }, + + /* ich6_sata_ahci: 8 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SATA | + PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | + PIIX_FLAG_AHCI, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &piix_sata_ops, + }, + + /* ich6m_sata_ahci: 9 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SATA | + PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | + PIIX_FLAG_AHCI, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &piix_sata_ops, + }, + + /* ich7m_sata_ahci: 10 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SATA | + PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | + PIIX_FLAG_AHCI, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &piix_sata_ops, + }, + + /* ich8_sata_ahci: 11 */ + { + .sht = &piix_sht, + .flags = ATA_FLAG_SATA | + PIIX_FLAG_CHECKINTR | PIIX_FLAG_SCR | + PIIX_FLAG_AHCI, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &piix_sata_ops, + }, + +}; + +static struct pci_bits piix_enable_bits[] = { + { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ + { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ +}; + +MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik"); +MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, piix_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +static int force_pcs = 0; +module_param(force_pcs, int, 0444); +MODULE_PARM_DESC(force_pcs, "force honoring or ignoring PCS to work around " + "device mis-detection (0=default, 1=ignore PCS, 2=honor PCS)"); + +/** + * piix_pata_cbl_detect - Probe host controller cable detect info + * @ap: Port for which cable detect info is desired + * + * Read 80c cable indicator from ATA PCI device's PCI config + * register. This register is normally set by firmware (BIOS). + * + * LOCKING: + * None (inherited from caller). + */ + +static void ich_pata_cbl_detect(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 tmp, mask; + + /* no 80c support in host controller? */ + if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0) + goto cbl40; + + /* check BIOS cable detect results */ + mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC; + pci_read_config_byte(pdev, PIIX_IOCFG, &tmp); + if ((tmp & mask) == 0) + goto cbl40; + + ap->cbl = ATA_CBL_PATA80; + return; + +cbl40: + ap->cbl = ATA_CBL_PATA40; +} + +/** + * piix_pata_prereset - prereset for PATA host controller + * @ap: Target port + * + * + * LOCKING: + * None (inherited from caller). + */ +static int piix_pata_prereset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) + return -ENOENT; + + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +static void piix_pata_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, piix_pata_prereset, ata_std_softreset, NULL, + ata_std_postreset); +} + + +/** + * ich_pata_prereset - prereset for PATA host controller + * @ap: Target port + * + * + * LOCKING: + * None (inherited from caller). + */ +static int ich_pata_prereset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no])) { + ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n"); + ap->eh_context.i.action &= ~ATA_EH_RESET_MASK; + return 0; + } + + ich_pata_cbl_detect(ap); + + return ata_std_prereset(ap); +} + +static void ich_pata_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, ich_pata_prereset, ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * piix_sata_present_mask - determine present mask for SATA host controller + * @ap: Target port + * + * Reads SATA PCI device's PCI config register Port Configuration + * and Status (PCS) to determine port and device availability. + * + * LOCKING: + * None (inherited from caller). + * + * RETURNS: + * determined present_mask + */ +static unsigned int piix_sata_present_mask(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct piix_host_priv *hpriv = ap->host->private_data; + const unsigned int *map = hpriv->map; + int base = 2 * ap->port_no; + unsigned int present_mask = 0; + int port, i; + u16 pcs; + + pci_read_config_word(pdev, ICH5_PCS, &pcs); + DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base); + + for (i = 0; i < 2; i++) { + port = map[base + i]; + if (port < 0) + continue; + if ((ap->flags & PIIX_FLAG_IGNORE_PCS) || + (pcs & 1 << (hpriv->map_db->present_shift + port))) + present_mask |= 1 << i; + } + + DPRINTK("ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n", + ap->id, pcs, present_mask); + + return present_mask; +} + +/** + * piix_sata_softreset - reset SATA host port via ATA SRST + * @ap: port to reset + * @classes: resulting classes of attached devices + * + * Reset SATA host port via ATA SRST. On controllers with + * reliable PCS present bits, the bits are used to determine + * device presence. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +static int piix_sata_softreset(struct ata_port *ap, unsigned int *classes) +{ + unsigned int present_mask; + int i, rc; + + present_mask = piix_sata_present_mask(ap); + + rc = ata_std_softreset(ap, classes); + if (rc) + return rc; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + if (!(present_mask & (1 << i))) + classes[i] = ATA_DEV_NONE; + } + + return 0; +} + +static void piix_sata_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, ata_std_prereset, piix_sata_softreset, NULL, + ata_std_postreset); +} + +/** + * piix_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *dev = to_pci_dev(ap->host->dev); + unsigned int is_slave = (adev->devno != 0); + unsigned int master_port= ap->port_no ? 0x42 : 0x40; + unsigned int slave_port = 0x44; + u16 master_data; + u8 slave_data; + u8 udma_enable; + int control = 0; + + /* + * See Intel Document 298600-004 for the timing programing rules + * for ICH controllers. + */ + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + if (pio >= 2) + control |= 1; /* TIME1 enable */ + if (ata_pio_need_iordy(adev)) + control |= 2; /* IE enable */ + + /* Intel specifies that the PPE functionality is for disk only */ + if (adev->class == ATA_DEV_ATA) + control |= 4; /* PPE enable */ + + pci_read_config_word(dev, master_port, &master_data); + if (is_slave) { + /* Enable SITRE (seperate slave timing register) */ + master_data |= 0x4000; + /* enable PPE1, IE1 and TIME1 as needed */ + master_data |= (control << 4); + pci_read_config_byte(dev, slave_port, &slave_data); + slave_data &= (ap->port_no ? 0x0f : 0xf0); + /* Load the timing nibble for this slave */ + slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); + } else { + /* Master keeps the bits in a different format */ + master_data &= 0xccf8; + /* Enable PPE, IE and TIME as appropriate */ + master_data |= control; + master_data |= + (timings[pio][0] << 12) | + (timings[pio][1] << 8); + } + pci_write_config_word(dev, master_port, master_data); + if (is_slave) + pci_write_config_byte(dev, slave_port, slave_data); + + /* Ensure the UDMA bit is off - it will be turned back on if + UDMA is selected */ + + if (ap->udma_mask) { + pci_read_config_byte(dev, 0x48, &udma_enable); + udma_enable &= ~(1 << (2 * ap->port_no + adev->devno)); + pci_write_config_byte(dev, 0x48, udma_enable); + } +} + +/** + * do_pata_set_dmamode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Drive in question + * @udma: udma mode, 0 - 6 + * @isich: set if the chip is an ICH device + * + * Set UDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, int isich) +{ + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u8 master_port = ap->port_no ? 0x42 : 0x40; + u16 master_data; + u8 speed = adev->dma_mode; + int devid = adev->devno + 2 * ap->port_no; + u8 udma_enable; + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + pci_read_config_word(dev, master_port, &master_data); + pci_read_config_byte(dev, 0x48, &udma_enable); + + if (speed >= XFER_UDMA_0) { + unsigned int udma = adev->dma_mode - XFER_UDMA_0; + u16 udma_timing; + u16 ideconf; + int u_clock, u_speed; + + /* + * UDMA is handled by a combination of clock switching and + * selection of dividers + * + * Handy rule: Odd modes are UDMATIMx 01, even are 02 + * except UDMA0 which is 00 + */ + u_speed = min(2 - (udma & 1), udma); + if (udma == 5) + u_clock = 0x1000; /* 100Mhz */ + else if (udma > 2) + u_clock = 1; /* 66Mhz */ + else + u_clock = 0; /* 33Mhz */ + + udma_enable |= (1 << devid); + + /* Load the CT/RP selection */ + pci_read_config_word(dev, 0x4A, &udma_timing); + udma_timing &= ~(3 << (4 * devid)); + udma_timing |= u_speed << (4 * devid); + pci_write_config_word(dev, 0x4A, udma_timing); + + if (isich) { + /* Select a 33/66/100Mhz clock */ + pci_read_config_word(dev, 0x54, &ideconf); + ideconf &= ~(0x1001 << devid); + ideconf |= u_clock << devid; + /* For ICH or later we should set bit 10 for better + performance (WR_PingPong_En) */ + pci_write_config_word(dev, 0x54, ideconf); + } + } else { + /* + * MWDMA is driven by the PIO timings. We must also enable + * IORDY unconditionally along with TIME1. PPE has already + * been set when the PIO timing was set. + */ + unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; + unsigned int control; + u8 slave_data; + const unsigned int needed_pio[3] = { + XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 + }; + int pio = needed_pio[mwdma] - XFER_PIO_0; + + control = 3; /* IORDY|TIME1 */ + + /* If the drive MWDMA is faster than it can do PIO then + we must force PIO into PIO0 */ + + if (adev->pio_mode < needed_pio[mwdma]) + /* Enable DMA timing only */ + control |= 8; /* PIO cycles in PIO0 */ + + if (adev->devno) { /* Slave */ + master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ + master_data |= control << 4; + pci_read_config_byte(dev, 0x44, &slave_data); + slave_data &= (0x0F + 0xE1 * ap->port_no); + /* Load the matching timing */ + slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); + pci_write_config_byte(dev, 0x44, slave_data); + } else { /* Master */ + master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY + and master timing bits */ + master_data |= control; + master_data |= + (timings[pio][0] << 12) | + (timings[pio][1] << 8); + } + udma_enable &= ~(1 << devid); + pci_write_config_word(dev, master_port, master_data); + } + /* Don't scribble on 0x48 if the controller does not support UDMA */ + if (ap->udma_mask) + pci_write_config_byte(dev, 0x48, udma_enable); +} + +/** + * piix_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set MW/UDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + do_pata_set_dmamode(ap, adev, 0); +} + +/** + * ich_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set MW/UDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + do_pata_set_dmamode(ap, adev, 1); +} + +#define AHCI_PCI_BAR 5 +#define AHCI_GLOBAL_CTL 0x04 +#define AHCI_ENABLE (1 << 31) +static int piix_disable_ahci(struct pci_dev *pdev) +{ + void __iomem *mmio; + u32 tmp; + int rc = 0; + + /* BUG: pci_enable_device has not yet been called. This + * works because this device is usually set up by BIOS. + */ + + if (!pci_resource_start(pdev, AHCI_PCI_BAR) || + !pci_resource_len(pdev, AHCI_PCI_BAR)) + return 0; + + mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64); + if (!mmio) + return -ENOMEM; + + tmp = readl(mmio + AHCI_GLOBAL_CTL); + if (tmp & AHCI_ENABLE) { + tmp &= ~AHCI_ENABLE; + writel(tmp, mmio + AHCI_GLOBAL_CTL); + + tmp = readl(mmio + AHCI_GLOBAL_CTL); + if (tmp & AHCI_ENABLE) + rc = -EIO; + } + + pci_iounmap(pdev, mmio); + return rc; +} + +/** + * piix_check_450nx_errata - Check for problem 450NX setup + * @ata_dev: the PCI device to check + * + * Check for the present of 450NX errata #19 and errata #25. If + * they are found return an error code so we can turn off DMA + */ + +static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev) +{ + struct pci_dev *pdev = NULL; + u16 cfg; + u8 rev; + int no_piix_dma = 0; + + while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL) + { + /* Look for 450NX PXB. Check for problem configurations + A PCI quirk checks bit 6 already */ + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); + pci_read_config_word(pdev, 0x41, &cfg); + /* Only on the original revision: IDE DMA can hang */ + if (rev == 0x00) + no_piix_dma = 1; + /* On all revisions below 5 PXB bus lock must be disabled for IDE */ + else if (cfg & (1<<14) && rev < 5) + no_piix_dma = 2; + } + if (no_piix_dma) + dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n"); + if (no_piix_dma == 2) + dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n"); + return no_piix_dma; +} + +static void __devinit piix_init_pcs(struct pci_dev *pdev, + struct ata_port_info *pinfo, + const struct piix_map_db *map_db) +{ + u16 pcs, new_pcs; + + pci_read_config_word(pdev, ICH5_PCS, &pcs); + + new_pcs = pcs | map_db->port_enable; + + if (new_pcs != pcs) { + DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs); + pci_write_config_word(pdev, ICH5_PCS, new_pcs); + msleep(150); + } + + if (force_pcs == 1) { + dev_printk(KERN_INFO, &pdev->dev, + "force ignoring PCS (0x%x)\n", new_pcs); + pinfo[0].flags |= PIIX_FLAG_IGNORE_PCS; + pinfo[1].flags |= PIIX_FLAG_IGNORE_PCS; + } else if (force_pcs == 2) { + dev_printk(KERN_INFO, &pdev->dev, + "force honoring PCS (0x%x)\n", new_pcs); + pinfo[0].flags &= ~PIIX_FLAG_IGNORE_PCS; + pinfo[1].flags &= ~PIIX_FLAG_IGNORE_PCS; + } +} + +static void __devinit piix_init_sata_map(struct pci_dev *pdev, + struct ata_port_info *pinfo, + const struct piix_map_db *map_db) +{ + struct piix_host_priv *hpriv = pinfo[0].private_data; + const unsigned int *map; + int i, invalid_map = 0; + u8 map_value; + + pci_read_config_byte(pdev, ICH5_PMR, &map_value); + + map = map_db->map[map_value & map_db->mask]; + + dev_printk(KERN_INFO, &pdev->dev, "MAP ["); + for (i = 0; i < 4; i++) { + switch (map[i]) { + case RV: + invalid_map = 1; + printk(" XX"); + break; + + case NA: + printk(" --"); + break; + + case IDE: + WARN_ON((i & 1) || map[i + 1] != IDE); + pinfo[i / 2] = piix_port_info[ich_pata_100]; + pinfo[i / 2].private_data = hpriv; + i++; + printk(" IDE IDE"); + break; + + default: + printk(" P%d", map[i]); + if (i & 1) + pinfo[i / 2].flags |= ATA_FLAG_SLAVE_POSS; + break; + } + } + printk(" ]\n"); + + if (invalid_map) + dev_printk(KERN_ERR, &pdev->dev, + "invalid MAP value %u\n", map_value); + + hpriv->map = map; + hpriv->map_db = map_db; +} + +/** + * piix_init_one - Register PIIX ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in piix_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. We probe for combined mode (sigh), + * and then hand over control to libata, for it to do the rest. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int piix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_port_info port_info[2]; + struct ata_port_info *ppinfo[2] = { &port_info[0], &port_info[1] }; + struct piix_host_priv *hpriv; + unsigned long port_flags; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + /* no hotplugging support (FIXME) */ + if (!in_module_init) + return -ENODEV; + + hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL); + if (!hpriv) + return -ENOMEM; + + port_info[0] = piix_port_info[ent->driver_data]; + port_info[1] = piix_port_info[ent->driver_data]; + port_info[0].private_data = hpriv; + port_info[1].private_data = hpriv; + + port_flags = port_info[0].flags; + + if (port_flags & PIIX_FLAG_AHCI) { + u8 tmp; + pci_read_config_byte(pdev, PIIX_SCC, &tmp); + if (tmp == PIIX_AHCI_DEVICE) { + int rc = piix_disable_ahci(pdev); + if (rc) + return rc; + } + } + + /* Initialize SATA map */ + if (port_flags & ATA_FLAG_SATA) { + piix_init_sata_map(pdev, port_info, + piix_map_db_table[ent->driver_data]); + piix_init_pcs(pdev, port_info, + piix_map_db_table[ent->driver_data]); + } + + /* On ICH5, some BIOSen disable the interrupt using the + * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3. + * On ICH6, this bit has the same effect, but only when + * MSI is disabled (and it is disabled, as we don't use + * message-signalled interrupts currently). + */ + if (port_flags & PIIX_FLAG_CHECKINTR) + pci_intx(pdev, 1); + + if (piix_check_450nx_errata(pdev)) { + /* This writes into the master table but it does not + really matter for this errata as we will apply it to + all the PIIX devices on the board */ + port_info[0].mwdma_mask = 0; + port_info[0].udma_mask = 0; + port_info[1].mwdma_mask = 0; + port_info[1].udma_mask = 0; + } + return ata_pci_init_one(pdev, ppinfo, 2); +} + +static void piix_host_stop(struct ata_host *host) +{ + struct piix_host_priv *hpriv = host->private_data; + + ata_host_stop(host); + + kfree(hpriv); +} + +static int __init piix_init(void) +{ + int rc; + + DPRINTK("pci_register_driver\n"); + rc = pci_register_driver(&piix_pci_driver); + if (rc) + return rc; + + in_module_init = 0; + + DPRINTK("done\n"); + return 0; +} + +static void __exit piix_exit(void) +{ + pci_unregister_driver(&piix_pci_driver); +} + +module_init(piix_init); +module_exit(piix_exit); diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c new file mode 100644 index 00000000000..b4abd685036 --- /dev/null +++ b/drivers/ata/libata-core.c @@ -0,0 +1,6176 @@ +/* + * libata-core.c - helper library for ATA + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2003-2004 Red Hat, Inc. All rights reserved. + * Copyright 2003-2004 Jeff Garzik + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available from http://www.t13.org/ and + * http://www.sata-io.org/ + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/list.h> +#include <linux/mm.h> +#include <linux/highmem.h> +#include <linux/spinlock.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/timer.h> +#include <linux/interrupt.h> +#include <linux/completion.h> +#include <linux/suspend.h> +#include <linux/workqueue.h> +#include <linux/jiffies.h> +#include <linux/scatterlist.h> +#include <scsi/scsi.h> +#include <scsi/scsi_cmnd.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <asm/io.h> +#include <asm/semaphore.h> +#include <asm/byteorder.h> + +#include "libata.h" + +/* debounce timing parameters in msecs { interval, duration, timeout } */ +const unsigned long sata_deb_timing_normal[] = { 5, 100, 2000 }; +const unsigned long sata_deb_timing_hotplug[] = { 25, 500, 2000 }; +const unsigned long sata_deb_timing_long[] = { 100, 2000, 5000 }; + +static unsigned int ata_dev_init_params(struct ata_device *dev, + u16 heads, u16 sectors); +static unsigned int ata_dev_set_xfermode(struct ata_device *dev); +static void ata_dev_xfermask(struct ata_device *dev); + +static unsigned int ata_unique_id = 1; +static struct workqueue_struct *ata_wq; + +struct workqueue_struct *ata_aux_wq; + +int atapi_enabled = 1; +module_param(atapi_enabled, int, 0444); +MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on)"); + +int atapi_dmadir = 0; +module_param(atapi_dmadir, int, 0444); +MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off, 1=on)"); + +int libata_fua = 0; +module_param_named(fua, libata_fua, int, 0444); +MODULE_PARM_DESC(fua, "FUA support (0=off, 1=on)"); + +static int ata_probe_timeout = ATA_TMOUT_INTERNAL / HZ; +module_param(ata_probe_timeout, int, 0444); +MODULE_PARM_DESC(ata_probe_timeout, "Set ATA probing timeout (seconds)"); + +MODULE_AUTHOR("Jeff Garzik"); +MODULE_DESCRIPTION("Library module for ATA devices"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); + + +/** + * ata_tf_to_fis - Convert ATA taskfile to SATA FIS structure + * @tf: Taskfile to convert + * @fis: Buffer into which data will output + * @pmp: Port multiplier port + * + * Converts a standard ATA taskfile to a Serial ATA + * FIS structure (Register - Host to Device). + * + * LOCKING: + * Inherited from caller. + */ + +void ata_tf_to_fis(const struct ata_taskfile *tf, u8 *fis, u8 pmp) +{ + fis[0] = 0x27; /* Register - Host to Device FIS */ + fis[1] = (pmp & 0xf) | (1 << 7); /* Port multiplier number, + bit 7 indicates Command FIS */ + fis[2] = tf->command; + fis[3] = tf->feature; + + fis[4] = tf->lbal; + fis[5] = tf->lbam; + fis[6] = tf->lbah; + fis[7] = tf->device; + + fis[8] = tf->hob_lbal; + fis[9] = tf->hob_lbam; + fis[10] = tf->hob_lbah; + fis[11] = tf->hob_feature; + + fis[12] = tf->nsect; + fis[13] = tf->hob_nsect; + fis[14] = 0; + fis[15] = tf->ctl; + + fis[16] = 0; + fis[17] = 0; + fis[18] = 0; + fis[19] = 0; +} + +/** + * ata_tf_from_fis - Convert SATA FIS to ATA taskfile + * @fis: Buffer from which data will be input + * @tf: Taskfile to output + * + * Converts a serial ATA FIS structure to a standard ATA taskfile. + * + * LOCKING: + * Inherited from caller. + */ + +void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf) +{ + tf->command = fis[2]; /* status */ + tf->feature = fis[3]; /* error */ + + tf->lbal = fis[4]; + tf->lbam = fis[5]; + tf->lbah = fis[6]; + tf->device = fis[7]; + + tf->hob_lbal = fis[8]; + tf->hob_lbam = fis[9]; + tf->hob_lbah = fis[10]; + + tf->nsect = fis[12]; + tf->hob_nsect = fis[13]; +} + +static const u8 ata_rw_cmds[] = { + /* pio multi */ + ATA_CMD_READ_MULTI, + ATA_CMD_WRITE_MULTI, + ATA_CMD_READ_MULTI_EXT, + ATA_CMD_WRITE_MULTI_EXT, + 0, + 0, + 0, + ATA_CMD_WRITE_MULTI_FUA_EXT, + /* pio */ + ATA_CMD_PIO_READ, + ATA_CMD_PIO_WRITE, + ATA_CMD_PIO_READ_EXT, + ATA_CMD_PIO_WRITE_EXT, + 0, + 0, + 0, + 0, + /* dma */ + ATA_CMD_READ, + ATA_CMD_WRITE, + ATA_CMD_READ_EXT, + ATA_CMD_WRITE_EXT, + 0, + 0, + 0, + ATA_CMD_WRITE_FUA_EXT +}; + +/** + * ata_rwcmd_protocol - set taskfile r/w commands and protocol + * @qc: command to examine and configure + * + * Examine the device configuration and tf->flags to calculate + * the proper read/write commands and protocol to use. + * + * LOCKING: + * caller. + */ +int ata_rwcmd_protocol(struct ata_queued_cmd *qc) +{ + struct ata_taskfile *tf = &qc->tf; + struct ata_device *dev = qc->dev; + u8 cmd; + + int index, fua, lba48, write; + + fua = (tf->flags & ATA_TFLAG_FUA) ? 4 : 0; + lba48 = (tf->flags & ATA_TFLAG_LBA48) ? 2 : 0; + write = (tf->flags & ATA_TFLAG_WRITE) ? 1 : 0; + + if (dev->flags & ATA_DFLAG_PIO) { + tf->protocol = ATA_PROT_PIO; + index = dev->multi_count ? 0 : 8; + } else if (lba48 && (qc->ap->flags & ATA_FLAG_PIO_LBA48)) { + /* Unable to use DMA due to host limitation */ + tf->protocol = ATA_PROT_PIO; + index = dev->multi_count ? 0 : 8; + } else { + tf->protocol = ATA_PROT_DMA; + index = 16; + } + + cmd = ata_rw_cmds[index + fua + lba48 + write]; + if (cmd) { + tf->command = cmd; + return 0; + } + return -1; +} + +/** + * ata_pack_xfermask - Pack pio, mwdma and udma masks into xfer_mask + * @pio_mask: pio_mask + * @mwdma_mask: mwdma_mask + * @udma_mask: udma_mask + * + * Pack @pio_mask, @mwdma_mask and @udma_mask into a single + * unsigned int xfer_mask. + * + * LOCKING: + * None. + * + * RETURNS: + * Packed xfer_mask. + */ +static unsigned int ata_pack_xfermask(unsigned int pio_mask, + unsigned int mwdma_mask, + unsigned int udma_mask) +{ + return ((pio_mask << ATA_SHIFT_PIO) & ATA_MASK_PIO) | + ((mwdma_mask << ATA_SHIFT_MWDMA) & ATA_MASK_MWDMA) | + ((udma_mask << ATA_SHIFT_UDMA) & ATA_MASK_UDMA); +} + +/** + * ata_unpack_xfermask - Unpack xfer_mask into pio, mwdma and udma masks + * @xfer_mask: xfer_mask to unpack + * @pio_mask: resulting pio_mask + * @mwdma_mask: resulting mwdma_mask + * @udma_mask: resulting udma_mask + * + * Unpack @xfer_mask into @pio_mask, @mwdma_mask and @udma_mask. + * Any NULL distination masks will be ignored. + */ +static void ata_unpack_xfermask(unsigned int xfer_mask, + unsigned int *pio_mask, + unsigned int *mwdma_mask, + unsigned int *udma_mask) +{ + if (pio_mask) + *pio_mask = (xfer_mask & ATA_MASK_PIO) >> ATA_SHIFT_PIO; + if (mwdma_mask) + *mwdma_mask = (xfer_mask & ATA_MASK_MWDMA) >> ATA_SHIFT_MWDMA; + if (udma_mask) + *udma_mask = (xfer_mask & ATA_MASK_UDMA) >> ATA_SHIFT_UDMA; +} + +static const struct ata_xfer_ent { + int shift, bits; + u8 base; +} ata_xfer_tbl[] = { + { ATA_SHIFT_PIO, ATA_BITS_PIO, XFER_PIO_0 }, + { ATA_SHIFT_MWDMA, ATA_BITS_MWDMA, XFER_MW_DMA_0 }, + { ATA_SHIFT_UDMA, ATA_BITS_UDMA, XFER_UDMA_0 }, + { -1, }, +}; + +/** + * ata_xfer_mask2mode - Find matching XFER_* for the given xfer_mask + * @xfer_mask: xfer_mask of interest + * + * Return matching XFER_* value for @xfer_mask. Only the highest + * bit of @xfer_mask is considered. + * + * LOCKING: + * None. + * + * RETURNS: + * Matching XFER_* value, 0 if no match found. + */ +static u8 ata_xfer_mask2mode(unsigned int xfer_mask) +{ + int highbit = fls(xfer_mask) - 1; + const struct ata_xfer_ent *ent; + + for (ent = ata_xfer_tbl; ent->shift >= 0; ent++) + if (highbit >= ent->shift && highbit < ent->shift + ent->bits) + return ent->base + highbit - ent->shift; + return 0; +} + +/** + * ata_xfer_mode2mask - Find matching xfer_mask for XFER_* + * @xfer_mode: XFER_* of interest + * + * Return matching xfer_mask for @xfer_mode. + * + * LOCKING: + * None. + * + * RETURNS: + * Matching xfer_mask, 0 if no match found. + */ +static unsigned int ata_xfer_mode2mask(u8 xfer_mode) +{ + const struct ata_xfer_ent *ent; + + for (ent = ata_xfer_tbl; ent->shift >= 0; ent++) + if (xfer_mode >= ent->base && xfer_mode < ent->base + ent->bits) + return 1 << (ent->shift + xfer_mode - ent->base); + return 0; +} + +/** + * ata_xfer_mode2shift - Find matching xfer_shift for XFER_* + * @xfer_mode: XFER_* of interest + * + * Return matching xfer_shift for @xfer_mode. + * + * LOCKING: + * None. + * + * RETURNS: + * Matching xfer_shift, -1 if no match found. + */ +static int ata_xfer_mode2shift(unsigned int xfer_mode) +{ + const struct ata_xfer_ent *ent; + + for (ent = ata_xfer_tbl; ent->shift >= 0; ent++) + if (xfer_mode >= ent->base && xfer_mode < ent->base + ent->bits) + return ent->shift; + return -1; +} + +/** + * ata_mode_string - convert xfer_mask to string + * @xfer_mask: mask of bits supported; only highest bit counts. + * + * Determine string which represents the highest speed + * (highest bit in @modemask). + * + * LOCKING: + * None. + * + * RETURNS: + * Constant C string representing highest speed listed in + * @mode_mask, or the constant C string "<n/a>". + */ +static const char *ata_mode_string(unsigned int xfer_mask) +{ + static const char * const xfer_mode_str[] = { + "PIO0", + "PIO1", + "PIO2", + "PIO3", + "PIO4", + "PIO5", + "PIO6", + "MWDMA0", + "MWDMA1", + "MWDMA2", + "MWDMA3", + "MWDMA4", + "UDMA/16", + "UDMA/25", + "UDMA/33", + "UDMA/44", + "UDMA/66", + "UDMA/100", + "UDMA/133", + "UDMA7", + }; + int highbit; + + highbit = fls(xfer_mask) - 1; + if (highbit >= 0 && highbit < ARRAY_SIZE(xfer_mode_str)) + return xfer_mode_str[highbit]; + return "<n/a>"; +} + +static const char *sata_spd_string(unsigned int spd) +{ + static const char * const spd_str[] = { + "1.5 Gbps", + "3.0 Gbps", + }; + + if (spd == 0 || (spd - 1) >= ARRAY_SIZE(spd_str)) + return "<unknown>"; + return spd_str[spd - 1]; +} + +void ata_dev_disable(struct ata_device *dev) +{ + if (ata_dev_enabled(dev) && ata_msg_drv(dev->ap)) { + ata_dev_printk(dev, KERN_WARNING, "disabled\n"); + dev->class++; + } +} + +/** + * ata_pio_devchk - PATA device presence detection + * @ap: ATA channel to examine + * @device: Device to examine (starting at zero) + * + * This technique was originally described in + * Hale Landis's ATADRVR (www.ata-atapi.com), and + * later found its way into the ATA/ATAPI spec. + * + * Write a pattern to the ATA shadow registers, + * and if a device is present, it will respond by + * correctly storing and echoing back the + * ATA shadow register contents. + * + * LOCKING: + * caller. + */ + +static unsigned int ata_pio_devchk(struct ata_port *ap, + unsigned int device) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + u8 nsect, lbal; + + ap->ops->dev_select(ap, device); + + outb(0x55, ioaddr->nsect_addr); + outb(0xaa, ioaddr->lbal_addr); + + outb(0xaa, ioaddr->nsect_addr); + outb(0x55, ioaddr->lbal_addr); + + outb(0x55, ioaddr->nsect_addr); + outb(0xaa, ioaddr->lbal_addr); + + nsect = inb(ioaddr->nsect_addr); + lbal = inb(ioaddr->lbal_addr); + + if ((nsect == 0x55) && (lbal == 0xaa)) + return 1; /* we found a device */ + + return 0; /* nothing found */ +} + +/** + * ata_mmio_devchk - PATA device presence detection + * @ap: ATA channel to examine + * @device: Device to examine (starting at zero) + * + * This technique was originally described in + * Hale Landis's ATADRVR (www.ata-atapi.com), and + * later found its way into the ATA/ATAPI spec. + * + * Write a pattern to the ATA shadow registers, + * and if a device is present, it will respond by + * correctly storing and echoing back the + * ATA shadow register contents. + * + * LOCKING: + * caller. + */ + +static unsigned int ata_mmio_devchk(struct ata_port *ap, + unsigned int device) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + u8 nsect, lbal; + + ap->ops->dev_select(ap, device); + + writeb(0x55, (void __iomem *) ioaddr->nsect_addr); + writeb(0xaa, (void __iomem *) ioaddr->lbal_addr); + + writeb(0xaa, (void __iomem *) ioaddr->nsect_addr); + writeb(0x55, (void __iomem *) ioaddr->lbal_addr); + + writeb(0x55, (void __iomem *) ioaddr->nsect_addr); + writeb(0xaa, (void __iomem *) ioaddr->lbal_addr); + + nsect = readb((void __iomem *) ioaddr->nsect_addr); + lbal = readb((void __iomem *) ioaddr->lbal_addr); + + if ((nsect == 0x55) && (lbal == 0xaa)) + return 1; /* we found a device */ + + return 0; /* nothing found */ +} + +/** + * ata_devchk - PATA device presence detection + * @ap: ATA channel to examine + * @device: Device to examine (starting at zero) + * + * Dispatch ATA device presence detection, depending + * on whether we are using PIO or MMIO to talk to the + * ATA shadow registers. + * + * LOCKING: + * caller. + */ + +static unsigned int ata_devchk(struct ata_port *ap, + unsigned int device) +{ + if (ap->flags & ATA_FLAG_MMIO) + return ata_mmio_devchk(ap, device); + return ata_pio_devchk(ap, device); +} + +/** + * ata_dev_classify - determine device type based on ATA-spec signature + * @tf: ATA taskfile register set for device to be identified + * + * Determine from taskfile register contents whether a device is + * ATA or ATAPI, as per "Signature and persistence" section + * of ATA/PI spec (volume 1, sect 5.14). + * + * LOCKING: + * None. + * + * RETURNS: + * Device type, %ATA_DEV_ATA, %ATA_DEV_ATAPI, or %ATA_DEV_UNKNOWN + * the event of failure. + */ + +unsigned int ata_dev_classify(const struct ata_taskfile *tf) +{ + /* Apple's open source Darwin code hints that some devices only + * put a proper signature into the LBA mid/high registers, + * So, we only check those. It's sufficient for uniqueness. + */ + + if (((tf->lbam == 0) && (tf->lbah == 0)) || + ((tf->lbam == 0x3c) && (tf->lbah == 0xc3))) { + DPRINTK("found ATA device by sig\n"); + return ATA_DEV_ATA; + } + + if (((tf->lbam == 0x14) && (tf->lbah == 0xeb)) || + ((tf->lbam == 0x69) && (tf->lbah == 0x96))) { + DPRINTK("found ATAPI device by sig\n"); + return ATA_DEV_ATAPI; + } + + DPRINTK("unknown device\n"); + return ATA_DEV_UNKNOWN; +} + +/** + * ata_dev_try_classify - Parse returned ATA device signature + * @ap: ATA channel to examine + * @device: Device to examine (starting at zero) + * @r_err: Value of error register on completion + * + * After an event -- SRST, E.D.D., or SATA COMRESET -- occurs, + * an ATA/ATAPI-defined set of values is placed in the ATA + * shadow registers, indicating the results of device detection + * and diagnostics. + * + * Select the ATA device, and read the values from the ATA shadow + * registers. Then parse according to the Error register value, + * and the spec-defined values examined by ata_dev_classify(). + * + * LOCKING: + * caller. + * + * RETURNS: + * Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE. + */ + +static unsigned int +ata_dev_try_classify(struct ata_port *ap, unsigned int device, u8 *r_err) +{ + struct ata_taskfile tf; + unsigned int class; + u8 err; + + ap->ops->dev_select(ap, device); + + memset(&tf, 0, sizeof(tf)); + + ap->ops->tf_read(ap, &tf); + err = tf.feature; + if (r_err) + *r_err = err; + + /* see if device passed diags: if master then continue and warn later */ + if (err == 0 && device == 0) + /* diagnostic fail : do nothing _YET_ */ + ap->device[device].horkage |= ATA_HORKAGE_DIAGNOSTIC; + else if (err == 1) + /* do nothing */ ; + else if ((device == 0) && (err == 0x81)) + /* do nothing */ ; + else + return ATA_DEV_NONE; + + /* determine if device is ATA or ATAPI */ + class = ata_dev_classify(&tf); + + if (class == ATA_DEV_UNKNOWN) + return ATA_DEV_NONE; + if ((class == ATA_DEV_ATA) && (ata_chk_status(ap) == 0)) + return ATA_DEV_NONE; + return class; +} + +/** + * ata_id_string - Convert IDENTIFY DEVICE page into string + * @id: IDENTIFY DEVICE results we will examine + * @s: string into which data is output + * @ofs: offset into identify device page + * @len: length of string to return. must be an even number. + * + * The strings in the IDENTIFY DEVICE page are broken up into + * 16-bit chunks. Run through the string, and output each + * 8-bit chunk linearly, regardless of platform. + * + * LOCKING: + * caller. + */ + +void ata_id_string(const u16 *id, unsigned char *s, + unsigned int ofs, unsigned int len) +{ + unsigned int c; + + while (len > 0) { + c = id[ofs] >> 8; + *s = c; + s++; + + c = id[ofs] & 0xff; + *s = c; + s++; + + ofs++; + len -= 2; + } +} + +/** + * ata_id_c_string - Convert IDENTIFY DEVICE page into C string + * @id: IDENTIFY DEVICE results we will examine + * @s: string into which data is output + * @ofs: offset into identify device page + * @len: length of string to return. must be an odd number. + * + * This function is identical to ata_id_string except that it + * trims trailing spaces and terminates the resulting string with + * null. @len must be actual maximum length (even number) + 1. + * + * LOCKING: + * caller. + */ +void ata_id_c_string(const u16 *id, unsigned char *s, + unsigned int ofs, unsigned int len) +{ + unsigned char *p; + + WARN_ON(!(len & 1)); + + ata_id_string(id, s, ofs, len - 1); + + p = s + strnlen(s, len - 1); + while (p > s && p[-1] == ' ') + p--; + *p = '\0'; +} + +static u64 ata_id_n_sectors(const u16 *id) +{ + if (ata_id_has_lba(id)) { + if (ata_id_has_lba48(id)) + return ata_id_u64(id, 100); + else + return ata_id_u32(id, 60); + } else { + if (ata_id_current_chs_valid(id)) + return ata_id_u32(id, 57); + else + return id[1] * id[3] * id[6]; + } +} + +/** + * ata_noop_dev_select - Select device 0/1 on ATA bus + * @ap: ATA channel to manipulate + * @device: ATA device (numbered from zero) to select + * + * This function performs no actual function. + * + * May be used as the dev_select() entry in ata_port_operations. + * + * LOCKING: + * caller. + */ +void ata_noop_dev_select (struct ata_port *ap, unsigned int device) +{ +} + + +/** + * ata_std_dev_select - Select device 0/1 on ATA bus + * @ap: ATA channel to manipulate + * @device: ATA device (numbered from zero) to select + * + * Use the method defined in the ATA specification to + * make either device 0, or device 1, active on the + * ATA channel. Works with both PIO and MMIO. + * + * May be used as the dev_select() entry in ata_port_operations. + * + * LOCKING: + * caller. + */ + +void ata_std_dev_select (struct ata_port *ap, unsigned int device) +{ + u8 tmp; + + if (device == 0) + tmp = ATA_DEVICE_OBS; + else + tmp = ATA_DEVICE_OBS | ATA_DEV1; + + if (ap->flags & ATA_FLAG_MMIO) { + writeb(tmp, (void __iomem *) ap->ioaddr.device_addr); + } else { + outb(tmp, ap->ioaddr.device_addr); + } + ata_pause(ap); /* needed; also flushes, for mmio */ +} + +/** + * ata_dev_select - Select device 0/1 on ATA bus + * @ap: ATA channel to manipulate + * @device: ATA device (numbered from zero) to select + * @wait: non-zero to wait for Status register BSY bit to clear + * @can_sleep: non-zero if context allows sleeping + * + * Use the method defined in the ATA specification to + * make either device 0, or device 1, active on the + * ATA channel. + * + * This is a high-level version of ata_std_dev_select(), + * which additionally provides the services of inserting + * the proper pauses and status polling, where needed. + * + * LOCKING: + * caller. + */ + +void ata_dev_select(struct ata_port *ap, unsigned int device, + unsigned int wait, unsigned int can_sleep) +{ + if (ata_msg_probe(ap)) + ata_port_printk(ap, KERN_INFO, "ata_dev_select: ENTER, ata%u: " + "device %u, wait %u\n", ap->id, device, wait); + + if (wait) + ata_wait_idle(ap); + + ap->ops->dev_select(ap, device); + + if (wait) { + if (can_sleep && ap->device[device].class == ATA_DEV_ATAPI) + msleep(150); + ata_wait_idle(ap); + } +} + +/** + * ata_dump_id - IDENTIFY DEVICE info debugging output + * @id: IDENTIFY DEVICE page to dump + * + * Dump selected 16-bit words from the given IDENTIFY DEVICE + * page. + * + * LOCKING: + * caller. + */ + +static inline void ata_dump_id(const u16 *id) +{ + DPRINTK("49==0x%04x " + "53==0x%04x " + "63==0x%04x " + "64==0x%04x " + "75==0x%04x \n", + id[49], + id[53], + id[63], + id[64], + id[75]); + DPRINTK("80==0x%04x " + "81==0x%04x " + "82==0x%04x " + "83==0x%04x " + "84==0x%04x \n", + id[80], + id[81], + id[82], + id[83], + id[84]); + DPRINTK("88==0x%04x " + "93==0x%04x\n", + id[88], + id[93]); +} + +/** + * ata_id_xfermask - Compute xfermask from the given IDENTIFY data + * @id: IDENTIFY data to compute xfer mask from + * + * Compute the xfermask for this device. This is not as trivial + * as it seems if we must consider early devices correctly. + * + * FIXME: pre IDE drive timing (do we care ?). + * + * LOCKING: + * None. + * + * RETURNS: + * Computed xfermask + */ +static unsigned int ata_id_xfermask(const u16 *id) +{ + unsigned int pio_mask, mwdma_mask, udma_mask; + + /* Usual case. Word 53 indicates word 64 is valid */ + if (id[ATA_ID_FIELD_VALID] & (1 << 1)) { + pio_mask = id[ATA_ID_PIO_MODES] & 0x03; + pio_mask <<= 3; + pio_mask |= 0x7; + } else { + /* If word 64 isn't valid then Word 51 high byte holds + * the PIO timing number for the maximum. Turn it into + * a mask. + */ + pio_mask = (2 << (id[ATA_ID_OLD_PIO_MODES] & 0xFF)) - 1 ; + + /* But wait.. there's more. Design your standards by + * committee and you too can get a free iordy field to + * process. However its the speeds not the modes that + * are supported... Note drivers using the timing API + * will get this right anyway + */ + } + + mwdma_mask = id[ATA_ID_MWDMA_MODES] & 0x07; + + if (ata_id_is_cfa(id)) { + /* + * Process compact flash extended modes + */ + int pio = id[163] & 0x7; + int dma = (id[163] >> 3) & 7; + + if (pio) + pio_mask |= (1 << 5); + if (pio > 1) + pio_mask |= (1 << 6); + if (dma) + mwdma_mask |= (1 << 3); + if (dma > 1) + mwdma_mask |= (1 << 4); + } + + udma_mask = 0; + if (id[ATA_ID_FIELD_VALID] & (1 << 2)) + udma_mask = id[ATA_ID_UDMA_MODES] & 0xff; + + return ata_pack_xfermask(pio_mask, mwdma_mask, udma_mask); +} + +/** + * ata_port_queue_task - Queue port_task + * @ap: The ata_port to queue port_task for + * @fn: workqueue function to be scheduled + * @data: data value to pass to workqueue function + * @delay: delay time for workqueue function + * + * Schedule @fn(@data) for execution after @delay jiffies using + * port_task. There is one port_task per port and it's the + * user(low level driver)'s responsibility to make sure that only + * one task is active at any given time. + * + * libata core layer takes care of synchronization between + * port_task and EH. ata_port_queue_task() may be ignored for EH + * synchronization. + * + * LOCKING: + * Inherited from caller. + */ +void ata_port_queue_task(struct ata_port *ap, void (*fn)(void *), void *data, + unsigned long delay) +{ + int rc; + + if (ap->pflags & ATA_PFLAG_FLUSH_PORT_TASK) + return; + + PREPARE_WORK(&ap->port_task, fn, data); + + if (!delay) + rc = queue_work(ata_wq, &ap->port_task); + else + rc = queue_delayed_work(ata_wq, &ap->port_task, delay); + + /* rc == 0 means that another user is using port task */ + WARN_ON(rc == 0); +} + +/** + * ata_port_flush_task - Flush port_task + * @ap: The ata_port to flush port_task for + * + * After this function completes, port_task is guranteed not to + * be running or scheduled. + * + * LOCKING: + * Kernel thread context (may sleep) + */ +void ata_port_flush_task(struct ata_port *ap) +{ + unsigned long flags; + + DPRINTK("ENTER\n"); + + spin_lock_irqsave(ap->lock, flags); + ap->pflags |= ATA_PFLAG_FLUSH_PORT_TASK; + spin_unlock_irqrestore(ap->lock, flags); + + DPRINTK("flush #1\n"); + flush_workqueue(ata_wq); + + /* + * At this point, if a task is running, it's guaranteed to see + * the FLUSH flag; thus, it will never queue pio tasks again. + * Cancel and flush. + */ + if (!cancel_delayed_work(&ap->port_task)) { + if (ata_msg_ctl(ap)) + ata_port_printk(ap, KERN_DEBUG, "%s: flush #2\n", + __FUNCTION__); + flush_workqueue(ata_wq); + } + + spin_lock_irqsave(ap->lock, flags); + ap->pflags &= ~ATA_PFLAG_FLUSH_PORT_TASK; + spin_unlock_irqrestore(ap->lock, flags); + + if (ata_msg_ctl(ap)) + ata_port_printk(ap, KERN_DEBUG, "%s: EXIT\n", __FUNCTION__); +} + +void ata_qc_complete_internal(struct ata_queued_cmd *qc) +{ + struct completion *waiting = qc->private_data; + + complete(waiting); +} + +/** + * ata_exec_internal - execute libata internal command + * @dev: Device to which the command is sent + * @tf: Taskfile registers for the command and the result + * @cdb: CDB for packet command + * @dma_dir: Data tranfer direction of the command + * @buf: Data buffer of the command + * @buflen: Length of data buffer + * + * Executes libata internal command with timeout. @tf contains + * command on entry and result on return. Timeout and error + * conditions are reported via return value. No recovery action + * is taken after a command times out. It's caller's duty to + * clean up after timeout. + * + * LOCKING: + * None. Should be called with kernel context, might sleep. + * + * RETURNS: + * Zero on success, AC_ERR_* mask on failure + */ +unsigned ata_exec_internal(struct ata_device *dev, + struct ata_taskfile *tf, const u8 *cdb, + int dma_dir, void *buf, unsigned int buflen) +{ + struct ata_port *ap = dev->ap; + u8 command = tf->command; + struct ata_queued_cmd *qc; + unsigned int tag, preempted_tag; + u32 preempted_sactive, preempted_qc_active; + DECLARE_COMPLETION_ONSTACK(wait); + unsigned long flags; + unsigned int err_mask; + int rc; + + spin_lock_irqsave(ap->lock, flags); + + /* no internal command while frozen */ + if (ap->pflags & ATA_PFLAG_FROZEN) { + spin_unlock_irqrestore(ap->lock, flags); + return AC_ERR_SYSTEM; + } + + /* initialize internal qc */ + + /* XXX: Tag 0 is used for drivers with legacy EH as some + * drivers choke if any other tag is given. This breaks + * ata_tag_internal() test for those drivers. Don't use new + * EH stuff without converting to it. + */ + if (ap->ops->error_handler) + tag = ATA_TAG_INTERNAL; + else + tag = 0; + + if (test_and_set_bit(tag, &ap->qc_allocated)) + BUG(); + qc = __ata_qc_from_tag(ap, tag); + + qc->tag = tag; + qc->scsicmd = NULL; + qc->ap = ap; + qc->dev = dev; + ata_qc_reinit(qc); + + preempted_tag = ap->active_tag; + preempted_sactive = ap->sactive; + preempted_qc_active = ap->qc_active; + ap->active_tag = ATA_TAG_POISON; + ap->sactive = 0; + ap->qc_active = 0; + + /* prepare & issue qc */ + qc->tf = *tf; + if (cdb) + memcpy(qc->cdb, cdb, ATAPI_CDB_LEN); + qc->flags |= ATA_QCFLAG_RESULT_TF; + qc->dma_dir = dma_dir; + if (dma_dir != DMA_NONE) { + ata_sg_init_one(qc, buf, buflen); + qc->nsect = buflen / ATA_SECT_SIZE; + } + + qc->private_data = &wait; + qc->complete_fn = ata_qc_complete_internal; + + ata_qc_issue(qc); + + spin_unlock_irqrestore(ap->lock, flags); + + rc = wait_for_completion_timeout(&wait, ata_probe_timeout); + + ata_port_flush_task(ap); + + if (!rc) { + spin_lock_irqsave(ap->lock, flags); + + /* We're racing with irq here. If we lose, the + * following test prevents us from completing the qc + * twice. If we win, the port is frozen and will be + * cleaned up by ->post_internal_cmd(). + */ + if (qc->flags & ATA_QCFLAG_ACTIVE) { + qc->err_mask |= AC_ERR_TIMEOUT; + + if (ap->ops->error_handler) + ata_port_freeze(ap); + else + ata_qc_complete(qc); + + if (ata_msg_warn(ap)) + ata_dev_printk(dev, KERN_WARNING, + "qc timeout (cmd 0x%x)\n", command); + } + + spin_unlock_irqrestore(ap->lock, flags); + } + + /* do post_internal_cmd */ + if (ap->ops->post_internal_cmd) + ap->ops->post_internal_cmd(qc); + + if (qc->flags & ATA_QCFLAG_FAILED && !qc->err_mask) { + if (ata_msg_warn(ap)) + ata_dev_printk(dev, KERN_WARNING, + "zero err_mask for failed " + "internal command, assuming AC_ERR_OTHER\n"); + qc->err_mask |= AC_ERR_OTHER; + } + + /* finish up */ + spin_lock_irqsave(ap->lock, flags); + + *tf = qc->result_tf; + err_mask = qc->err_mask; + + ata_qc_free(qc); + ap->active_tag = preempted_tag; + ap->sactive = preempted_sactive; + ap->qc_active = preempted_qc_active; + + /* XXX - Some LLDDs (sata_mv) disable port on command failure. + * Until those drivers are fixed, we detect the condition + * here, fail the command with AC_ERR_SYSTEM and reenable the + * port. + * + * Note that this doesn't change any behavior as internal + * command failure results in disabling the device in the + * higher layer for LLDDs without new reset/EH callbacks. + * + * Kill the following code as soon as those drivers are fixed. + */ + if (ap->flags & ATA_FLAG_DISABLED) { + err_mask |= AC_ERR_SYSTEM; + ata_port_probe(ap); + } + + spin_unlock_irqrestore(ap->lock, flags); + + return err_mask; +} + +/** + * ata_do_simple_cmd - execute simple internal command + * @dev: Device to which the command is sent + * @cmd: Opcode to execute + * + * Execute a 'simple' command, that only consists of the opcode + * 'cmd' itself, without filling any other registers + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * Zero on success, AC_ERR_* mask on failure + */ +unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd) +{ + struct ata_taskfile tf; + + ata_tf_init(dev, &tf); + + tf.command = cmd; + tf.flags |= ATA_TFLAG_DEVICE; + tf.protocol = ATA_PROT_NODATA; + + return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); +} + +/** + * ata_pio_need_iordy - check if iordy needed + * @adev: ATA device + * + * Check if the current speed of the device requires IORDY. Used + * by various controllers for chip configuration. + */ + +unsigned int ata_pio_need_iordy(const struct ata_device *adev) +{ + int pio; + int speed = adev->pio_mode - XFER_PIO_0; + + if (speed < 2) + return 0; + if (speed > 2) + return 1; + + /* If we have no drive specific rule, then PIO 2 is non IORDY */ + + if (adev->id[ATA_ID_FIELD_VALID] & 2) { /* EIDE */ + pio = adev->id[ATA_ID_EIDE_PIO]; + /* Is the speed faster than the drive allows non IORDY ? */ + if (pio) { + /* This is cycle times not frequency - watch the logic! */ + if (pio > 240) /* PIO2 is 240nS per cycle */ + return 1; + return 0; + } + } + return 0; +} + +/** + * ata_dev_read_id - Read ID data from the specified device + * @dev: target device + * @p_class: pointer to class of the target device (may be changed) + * @post_reset: is this read ID post-reset? + * @id: buffer to read IDENTIFY data into + * + * Read ID data from the specified device. ATA_CMD_ID_ATA is + * performed on ATA devices and ATA_CMD_ID_ATAPI on ATAPI + * devices. This function also issues ATA_CMD_INIT_DEV_PARAMS + * for pre-ATA4 drives. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, + int post_reset, u16 *id) +{ + struct ata_port *ap = dev->ap; + unsigned int class = *p_class; + struct ata_taskfile tf; + unsigned int err_mask = 0; + const char *reason; + int rc; + + if (ata_msg_ctl(ap)) + ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER, host %u, dev %u\n", + __FUNCTION__, ap->id, dev->devno); + + ata_dev_select(ap, dev->devno, 1, 1); /* select device 0/1 */ + + retry: + ata_tf_init(dev, &tf); + + switch (class) { + case ATA_DEV_ATA: + tf.command = ATA_CMD_ID_ATA; + break; + case ATA_DEV_ATAPI: + tf.command = ATA_CMD_ID_ATAPI; + break; + default: + rc = -ENODEV; + reason = "unsupported class"; + goto err_out; + } + + tf.protocol = ATA_PROT_PIO; + + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE, + id, sizeof(id[0]) * ATA_ID_WORDS); + if (err_mask) { + rc = -EIO; + reason = "I/O error"; + goto err_out; + } + + swap_buf_le16(id, ATA_ID_WORDS); + + /* sanity check */ + rc = -EINVAL; + reason = "device reports illegal type"; + + if (class == ATA_DEV_ATA) { + if (!ata_id_is_ata(id) && !ata_id_is_cfa(id)) + goto err_out; + } else { + if (ata_id_is_ata(id)) + goto err_out; + } + + if (post_reset && class == ATA_DEV_ATA) { + /* + * The exact sequence expected by certain pre-ATA4 drives is: + * SRST RESET + * IDENTIFY + * INITIALIZE DEVICE PARAMETERS + * anything else.. + * Some drives were very specific about that exact sequence. + */ + if (ata_id_major_version(id) < 4 || !ata_id_has_lba(id)) { + err_mask = ata_dev_init_params(dev, id[3], id[6]); + if (err_mask) { + rc = -EIO; + reason = "INIT_DEV_PARAMS failed"; + goto err_out; + } + + /* current CHS translation info (id[53-58]) might be + * changed. reread the identify device info. + */ + post_reset = 0; + goto retry; + } + } + + *p_class = class; + + return 0; + + err_out: + if (ata_msg_warn(ap)) + ata_dev_printk(dev, KERN_WARNING, "failed to IDENTIFY " + "(%s, err_mask=0x%x)\n", reason, err_mask); + return rc; +} + +static inline u8 ata_dev_knobble(struct ata_device *dev) +{ + return ((dev->ap->cbl == ATA_CBL_SATA) && (!ata_id_is_sata(dev->id))); +} + +static void ata_dev_config_ncq(struct ata_device *dev, + char *desc, size_t desc_sz) +{ + struct ata_port *ap = dev->ap; + int hdepth = 0, ddepth = ata_id_queue_depth(dev->id); + + if (!ata_id_has_ncq(dev->id)) { + desc[0] = '\0'; + return; + } + + if (ap->flags & ATA_FLAG_NCQ) { + hdepth = min(ap->scsi_host->can_queue, ATA_MAX_QUEUE - 1); + dev->flags |= ATA_DFLAG_NCQ; + } + + if (hdepth >= ddepth) + snprintf(desc, desc_sz, "NCQ (depth %d)", ddepth); + else + snprintf(desc, desc_sz, "NCQ (depth %d/%d)", hdepth, ddepth); +} + +static void ata_set_port_max_cmd_len(struct ata_port *ap) +{ + int i; + + if (ap->scsi_host) { + unsigned int len = 0; + + for (i = 0; i < ATA_MAX_DEVICES; i++) + len = max(len, ap->device[i].cdb_len); + + ap->scsi_host->max_cmd_len = len; + } +} + +/** + * ata_dev_configure - Configure the specified ATA/ATAPI device + * @dev: Target device to configure + * @print_info: Enable device info printout + * + * Configure @dev according to @dev->id. Generic and low-level + * driver specific fixups are also applied. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno otherwise + */ +int ata_dev_configure(struct ata_device *dev, int print_info) +{ + struct ata_port *ap = dev->ap; + const u16 *id = dev->id; + unsigned int xfer_mask; + char revbuf[7]; /* XYZ-99\0 */ + int rc; + + if (!ata_dev_enabled(dev) && ata_msg_info(ap)) { + ata_dev_printk(dev, KERN_INFO, + "%s: ENTER/EXIT (host %u, dev %u) -- nodev\n", + __FUNCTION__, ap->id, dev->devno); + return 0; + } + + if (ata_msg_probe(ap)) + ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER, host %u, dev %u\n", + __FUNCTION__, ap->id, dev->devno); + + /* print device capabilities */ + if (ata_msg_probe(ap)) + ata_dev_printk(dev, KERN_DEBUG, + "%s: cfg 49:%04x 82:%04x 83:%04x 84:%04x " + "85:%04x 86:%04x 87:%04x 88:%04x\n", + __FUNCTION__, + id[49], id[82], id[83], id[84], + id[85], id[86], id[87], id[88]); + + /* initialize to-be-configured parameters */ + dev->flags &= ~ATA_DFLAG_CFG_MASK; + dev->max_sectors = 0; + dev->cdb_len = 0; + dev->n_sectors = 0; + dev->cylinders = 0; + dev->heads = 0; + dev->sectors = 0; + + /* + * common ATA, ATAPI feature tests + */ + + /* find max transfer mode; for printk only */ + xfer_mask = ata_id_xfermask(id); + + if (ata_msg_probe(ap)) + ata_dump_id(id); + + /* ATA-specific feature tests */ + if (dev->class == ATA_DEV_ATA) { + if (ata_id_is_cfa(id)) { + if (id[162] & 1) /* CPRM may make this media unusable */ + ata_dev_printk(dev, KERN_WARNING, "ata%u: device %u supports DRM functions and may not be fully accessable.\n", + ap->id, dev->devno); + snprintf(revbuf, 7, "CFA"); + } + else + snprintf(revbuf, 7, "ATA-%d", ata_id_major_version(id)); + + dev->n_sectors = ata_id_n_sectors(id); + + if (ata_id_has_lba(id)) { + const char *lba_desc; + char ncq_desc[20]; + + lba_desc = "LBA"; + dev->flags |= ATA_DFLAG_LBA; + if (ata_id_has_lba48(id)) { + dev->flags |= ATA_DFLAG_LBA48; + lba_desc = "LBA48"; + } + + /* config NCQ */ + ata_dev_config_ncq(dev, ncq_desc, sizeof(ncq_desc)); + + /* print device info to dmesg */ + if (ata_msg_drv(ap) && print_info) + ata_dev_printk(dev, KERN_INFO, "%s, " + "max %s, %Lu sectors: %s %s\n", + revbuf, + ata_mode_string(xfer_mask), + (unsigned long long)dev->n_sectors, + lba_desc, ncq_desc); + } else { + /* CHS */ + + /* Default translation */ + dev->cylinders = id[1]; + dev->heads = id[3]; + dev->sectors = id[6]; + + if (ata_id_current_chs_valid(id)) { + /* Current CHS translation is valid. */ + dev->cylinders = id[54]; + dev->heads = id[55]; + dev->sectors = id[56]; + } + + /* print device info to dmesg */ + if (ata_msg_drv(ap) && print_info) + ata_dev_printk(dev, KERN_INFO, "%s, " + "max %s, %Lu sectors: CHS %u/%u/%u\n", + revbuf, + ata_mode_string(xfer_mask), + (unsigned long long)dev->n_sectors, + dev->cylinders, dev->heads, + dev->sectors); + } + + if (dev->id[59] & 0x100) { + dev->multi_count = dev->id[59] & 0xff; + if (ata_msg_drv(ap) && print_info) + ata_dev_printk(dev, KERN_INFO, + "ata%u: dev %u multi count %u\n", + ap->id, dev->devno, dev->multi_count); + } + + dev->cdb_len = 16; + } + + /* ATAPI-specific feature tests */ + else if (dev->class == ATA_DEV_ATAPI) { + char *cdb_intr_string = ""; + + rc = atapi_cdb_len(id); + if ((rc < 12) || (rc > ATAPI_CDB_LEN)) { + if (ata_msg_warn(ap)) + ata_dev_printk(dev, KERN_WARNING, + "unsupported CDB len\n"); + rc = -EINVAL; + goto err_out_nosup; + } + dev->cdb_len = (unsigned int) rc; + + if (ata_id_cdb_intr(dev->id)) { + dev->flags |= ATA_DFLAG_CDB_INTR; + cdb_intr_string = ", CDB intr"; + } + + /* print device info to dmesg */ + if (ata_msg_drv(ap) && print_info) + ata_dev_printk(dev, KERN_INFO, "ATAPI, max %s%s\n", + ata_mode_string(xfer_mask), + cdb_intr_string); + } + + if (dev->horkage & ATA_HORKAGE_DIAGNOSTIC) { + /* Let the user know. We don't want to disallow opens for + rescue purposes, or in case the vendor is just a blithering + idiot */ + if (print_info) { + ata_dev_printk(dev, KERN_WARNING, +"Drive reports diagnostics failure. This may indicate a drive\n"); + ata_dev_printk(dev, KERN_WARNING, +"fault or invalid emulation. Contact drive vendor for information.\n"); + } + } + + ata_set_port_max_cmd_len(ap); + + /* limit bridge transfers to udma5, 200 sectors */ + if (ata_dev_knobble(dev)) { + if (ata_msg_drv(ap) && print_info) + ata_dev_printk(dev, KERN_INFO, + "applying bridge limits\n"); + dev->udma_mask &= ATA_UDMA5; + dev->max_sectors = ATA_MAX_SECTORS; + } + + if (ap->ops->dev_config) + ap->ops->dev_config(ap, dev); + + if (ata_msg_probe(ap)) + ata_dev_printk(dev, KERN_DEBUG, "%s: EXIT, drv_stat = 0x%x\n", + __FUNCTION__, ata_chk_status(ap)); + return 0; + +err_out_nosup: + if (ata_msg_probe(ap)) + ata_dev_printk(dev, KERN_DEBUG, + "%s: EXIT, err\n", __FUNCTION__); + return rc; +} + +/** + * ata_bus_probe - Reset and probe ATA bus + * @ap: Bus to probe + * + * Master ATA bus probing function. Initiates a hardware-dependent + * bus reset, then attempts to identify any devices found on + * the bus. + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * Zero on success, negative errno otherwise. + */ + +int ata_bus_probe(struct ata_port *ap) +{ + unsigned int classes[ATA_MAX_DEVICES]; + int tries[ATA_MAX_DEVICES]; + int i, rc, down_xfermask; + struct ata_device *dev; + + ata_port_probe(ap); + + for (i = 0; i < ATA_MAX_DEVICES; i++) + tries[i] = ATA_PROBE_MAX_TRIES; + + retry: + down_xfermask = 0; + + /* reset and determine device classes */ + ap->ops->phy_reset(ap); + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + dev = &ap->device[i]; + + if (!(ap->flags & ATA_FLAG_DISABLED) && + dev->class != ATA_DEV_UNKNOWN) + classes[dev->devno] = dev->class; + else + classes[dev->devno] = ATA_DEV_NONE; + + dev->class = ATA_DEV_UNKNOWN; + } + + ata_port_probe(ap); + + /* after the reset the device state is PIO 0 and the controller + state is undefined. Record the mode */ + + for (i = 0; i < ATA_MAX_DEVICES; i++) + ap->device[i].pio_mode = XFER_PIO_0; + + /* read IDENTIFY page and configure devices */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + dev = &ap->device[i]; + + if (tries[i]) + dev->class = classes[i]; + + if (!ata_dev_enabled(dev)) + continue; + + rc = ata_dev_read_id(dev, &dev->class, 1, dev->id); + if (rc) + goto fail; + + rc = ata_dev_configure(dev, 1); + if (rc) + goto fail; + } + + /* configure transfer mode */ + rc = ata_set_mode(ap, &dev); + if (rc) { + down_xfermask = 1; + goto fail; + } + + for (i = 0; i < ATA_MAX_DEVICES; i++) + if (ata_dev_enabled(&ap->device[i])) + return 0; + + /* no device present, disable port */ + ata_port_disable(ap); + ap->ops->port_disable(ap); + return -ENODEV; + + fail: + switch (rc) { + case -EINVAL: + case -ENODEV: + tries[dev->devno] = 0; + break; + case -EIO: + sata_down_spd_limit(ap); + /* fall through */ + default: + tries[dev->devno]--; + if (down_xfermask && + ata_down_xfermask_limit(dev, tries[dev->devno] == 1)) + tries[dev->devno] = 0; + } + + if (!tries[dev->devno]) { + ata_down_xfermask_limit(dev, 1); + ata_dev_disable(dev); + } + + goto retry; +} + +/** + * ata_port_probe - Mark port as enabled + * @ap: Port for which we indicate enablement + * + * Modify @ap data structure such that the system + * thinks that the entire port is enabled. + * + * LOCKING: host lock, or some other form of + * serialization. + */ + +void ata_port_probe(struct ata_port *ap) +{ + ap->flags &= ~ATA_FLAG_DISABLED; +} + +/** + * sata_print_link_status - Print SATA link status + * @ap: SATA port to printk link status about + * + * This function prints link speed and status of a SATA link. + * + * LOCKING: + * None. + */ +static void sata_print_link_status(struct ata_port *ap) +{ + u32 sstatus, scontrol, tmp; + + if (sata_scr_read(ap, SCR_STATUS, &sstatus)) + return; + sata_scr_read(ap, SCR_CONTROL, &scontrol); + + if (ata_port_online(ap)) { + tmp = (sstatus >> 4) & 0xf; + ata_port_printk(ap, KERN_INFO, + "SATA link up %s (SStatus %X SControl %X)\n", + sata_spd_string(tmp), sstatus, scontrol); + } else { + ata_port_printk(ap, KERN_INFO, + "SATA link down (SStatus %X SControl %X)\n", + sstatus, scontrol); + } +} + +/** + * __sata_phy_reset - Wake/reset a low-level SATA PHY + * @ap: SATA port associated with target SATA PHY. + * + * This function issues commands to standard SATA Sxxx + * PHY registers, to wake up the phy (and device), and + * clear any reset condition. + * + * LOCKING: + * PCI/etc. bus probe sem. + * + */ +void __sata_phy_reset(struct ata_port *ap) +{ + u32 sstatus; + unsigned long timeout = jiffies + (HZ * 5); + + if (ap->flags & ATA_FLAG_SATA_RESET) { + /* issue phy wake/reset */ + sata_scr_write_flush(ap, SCR_CONTROL, 0x301); + /* Couldn't find anything in SATA I/II specs, but + * AHCI-1.1 10.4.2 says at least 1 ms. */ + mdelay(1); + } + /* phy wake/clear reset */ + sata_scr_write_flush(ap, SCR_CONTROL, 0x300); + + /* wait for phy to become ready, if necessary */ + do { + msleep(200); + sata_scr_read(ap, SCR_STATUS, &sstatus); + if ((sstatus & 0xf) != 1) + break; + } while (time_before(jiffies, timeout)); + + /* print link status */ + sata_print_link_status(ap); + + /* TODO: phy layer with polling, timeouts, etc. */ + if (!ata_port_offline(ap)) + ata_port_probe(ap); + else + ata_port_disable(ap); + + if (ap->flags & ATA_FLAG_DISABLED) + return; + + if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) { + ata_port_disable(ap); + return; + } + + ap->cbl = ATA_CBL_SATA; +} + +/** + * sata_phy_reset - Reset SATA bus. + * @ap: SATA port associated with target SATA PHY. + * + * This function resets the SATA bus, and then probes + * the bus for devices. + * + * LOCKING: + * PCI/etc. bus probe sem. + * + */ +void sata_phy_reset(struct ata_port *ap) +{ + __sata_phy_reset(ap); + if (ap->flags & ATA_FLAG_DISABLED) + return; + ata_bus_reset(ap); +} + +/** + * ata_dev_pair - return other device on cable + * @adev: device + * + * Obtain the other device on the same cable, or if none is + * present NULL is returned + */ + +struct ata_device *ata_dev_pair(struct ata_device *adev) +{ + struct ata_port *ap = adev->ap; + struct ata_device *pair = &ap->device[1 - adev->devno]; + if (!ata_dev_enabled(pair)) + return NULL; + return pair; +} + +/** + * ata_port_disable - Disable port. + * @ap: Port to be disabled. + * + * Modify @ap data structure such that the system + * thinks that the entire port is disabled, and should + * never attempt to probe or communicate with devices + * on this port. + * + * LOCKING: host lock, or some other form of + * serialization. + */ + +void ata_port_disable(struct ata_port *ap) +{ + ap->device[0].class = ATA_DEV_NONE; + ap->device[1].class = ATA_DEV_NONE; + ap->flags |= ATA_FLAG_DISABLED; +} + +/** + * sata_down_spd_limit - adjust SATA spd limit downward + * @ap: Port to adjust SATA spd limit for + * + * Adjust SATA spd limit of @ap downward. Note that this + * function only adjusts the limit. The change must be applied + * using sata_set_spd(). + * + * LOCKING: + * Inherited from caller. + * + * RETURNS: + * 0 on success, negative errno on failure + */ +int sata_down_spd_limit(struct ata_port *ap) +{ + u32 sstatus, spd, mask; + int rc, highbit; + + rc = sata_scr_read(ap, SCR_STATUS, &sstatus); + if (rc) + return rc; + + mask = ap->sata_spd_limit; + if (mask <= 1) + return -EINVAL; + highbit = fls(mask) - 1; + mask &= ~(1 << highbit); + + spd = (sstatus >> 4) & 0xf; + if (spd <= 1) + return -EINVAL; + spd--; + mask &= (1 << spd) - 1; + if (!mask) + return -EINVAL; + + ap->sata_spd_limit = mask; + + ata_port_printk(ap, KERN_WARNING, "limiting SATA link speed to %s\n", + sata_spd_string(fls(mask))); + + return 0; +} + +static int __sata_set_spd_needed(struct ata_port *ap, u32 *scontrol) +{ + u32 spd, limit; + + if (ap->sata_spd_limit == UINT_MAX) + limit = 0; + else + limit = fls(ap->sata_spd_limit); + + spd = (*scontrol >> 4) & 0xf; + *scontrol = (*scontrol & ~0xf0) | ((limit & 0xf) << 4); + + return spd != limit; +} + +/** + * sata_set_spd_needed - is SATA spd configuration needed + * @ap: Port in question + * + * Test whether the spd limit in SControl matches + * @ap->sata_spd_limit. This function is used to determine + * whether hardreset is necessary to apply SATA spd + * configuration. + * + * LOCKING: + * Inherited from caller. + * + * RETURNS: + * 1 if SATA spd configuration is needed, 0 otherwise. + */ +int sata_set_spd_needed(struct ata_port *ap) +{ + u32 scontrol; + + if (sata_scr_read(ap, SCR_CONTROL, &scontrol)) + return 0; + + return __sata_set_spd_needed(ap, &scontrol); +} + +/** + * sata_set_spd - set SATA spd according to spd limit + * @ap: Port to set SATA spd for + * + * Set SATA spd of @ap according to sata_spd_limit. + * + * LOCKING: + * Inherited from caller. + * + * RETURNS: + * 0 if spd doesn't need to be changed, 1 if spd has been + * changed. Negative errno if SCR registers are inaccessible. + */ +int sata_set_spd(struct ata_port *ap) +{ + u32 scontrol; + int rc; + + if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + return rc; + + if (!__sata_set_spd_needed(ap, &scontrol)) + return 0; + + if ((rc = sata_scr_write(ap, SCR_CONTROL, scontrol))) + return rc; + + return 1; +} + +/* + * This mode timing computation functionality is ported over from + * drivers/ide/ide-timing.h and was originally written by Vojtech Pavlik + */ +/* + * PIO 0-4, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds). + * These were taken from ATA/ATAPI-6 standard, rev 0a, except + * for UDMA6, which is currently supported only by Maxtor drives. + * + * For PIO 5/6 MWDMA 3/4 see the CFA specification 3.0. + */ + +static const struct ata_timing ata_timing[] = { + + { XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 15 }, + { XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 20 }, + { XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 30 }, + { XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 45 }, + + { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 80, 0 }, + { XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 100, 0 }, + { XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 60 }, + { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 80 }, + { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 120 }, + +/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 150 }, */ + + { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 120, 0 }, + { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 150, 0 }, + { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 480, 0 }, + + { XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 240, 0 }, + { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 480, 0 }, + { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 960, 0 }, + + { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 80, 0 }, + { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 100, 0 }, + { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 120, 0 }, + { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 180, 0 }, + + { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 240, 0 }, + { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 383, 0 }, + { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0 }, + +/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 960, 0 }, */ + + { 0xFF } +}; + +#define ENOUGH(v,unit) (((v)-1)/(unit)+1) +#define EZ(v,unit) ((v)?ENOUGH(v,unit):0) + +static void ata_timing_quantize(const struct ata_timing *t, struct ata_timing *q, int T, int UT) +{ + q->setup = EZ(t->setup * 1000, T); + q->act8b = EZ(t->act8b * 1000, T); + q->rec8b = EZ(t->rec8b * 1000, T); + q->cyc8b = EZ(t->cyc8b * 1000, T); + q->active = EZ(t->active * 1000, T); + q->recover = EZ(t->recover * 1000, T); + q->cycle = EZ(t->cycle * 1000, T); + q->udma = EZ(t->udma * 1000, UT); +} + +void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b, + struct ata_timing *m, unsigned int what) +{ + if (what & ATA_TIMING_SETUP ) m->setup = max(a->setup, b->setup); + if (what & ATA_TIMING_ACT8B ) m->act8b = max(a->act8b, b->act8b); + if (what & ATA_TIMING_REC8B ) m->rec8b = max(a->rec8b, b->rec8b); + if (what & ATA_TIMING_CYC8B ) m->cyc8b = max(a->cyc8b, b->cyc8b); + if (what & ATA_TIMING_ACTIVE ) m->active = max(a->active, b->active); + if (what & ATA_TIMING_RECOVER) m->recover = max(a->recover, b->recover); + if (what & ATA_TIMING_CYCLE ) m->cycle = max(a->cycle, b->cycle); + if (what & ATA_TIMING_UDMA ) m->udma = max(a->udma, b->udma); +} + +static const struct ata_timing* ata_timing_find_mode(unsigned short speed) +{ + const struct ata_timing *t; + + for (t = ata_timing; t->mode != speed; t++) + if (t->mode == 0xFF) + return NULL; + return t; +} + +int ata_timing_compute(struct ata_device *adev, unsigned short speed, + struct ata_timing *t, int T, int UT) +{ + const struct ata_timing *s; + struct ata_timing p; + + /* + * Find the mode. + */ + + if (!(s = ata_timing_find_mode(speed))) + return -EINVAL; + + memcpy(t, s, sizeof(*s)); + + /* + * If the drive is an EIDE drive, it can tell us it needs extended + * PIO/MW_DMA cycle timing. + */ + + if (adev->id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */ + memset(&p, 0, sizeof(p)); + if(speed >= XFER_PIO_0 && speed <= XFER_SW_DMA_0) { + if (speed <= XFER_PIO_2) p.cycle = p.cyc8b = adev->id[ATA_ID_EIDE_PIO]; + else p.cycle = p.cyc8b = adev->id[ATA_ID_EIDE_PIO_IORDY]; + } else if(speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2) { + p.cycle = adev->id[ATA_ID_EIDE_DMA_MIN]; + } + ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B); + } + + /* + * Convert the timing to bus clock counts. + */ + + ata_timing_quantize(t, t, T, UT); + + /* + * Even in DMA/UDMA modes we still use PIO access for IDENTIFY, + * S.M.A.R.T * and some other commands. We have to ensure that the + * DMA cycle timing is slower/equal than the fastest PIO timing. + */ + + if (speed > XFER_PIO_4) { + ata_timing_compute(adev, adev->pio_mode, &p, T, UT); + ata_timing_merge(&p, t, t, ATA_TIMING_ALL); + } + + /* + * Lengthen active & recovery time so that cycle time is correct. + */ + + if (t->act8b + t->rec8b < t->cyc8b) { + t->act8b += (t->cyc8b - (t->act8b + t->rec8b)) / 2; + t->rec8b = t->cyc8b - t->act8b; + } + + if (t->active + t->recover < t->cycle) { + t->active += (t->cycle - (t->active + t->recover)) / 2; + t->recover = t->cycle - t->active; + } + + return 0; +} + +/** + * ata_down_xfermask_limit - adjust dev xfer masks downward + * @dev: Device to adjust xfer masks + * @force_pio0: Force PIO0 + * + * Adjust xfer masks of @dev downward. Note that this function + * does not apply the change. Invoking ata_set_mode() afterwards + * will apply the limit. + * + * LOCKING: + * Inherited from caller. + * + * RETURNS: + * 0 on success, negative errno on failure + */ +int ata_down_xfermask_limit(struct ata_device *dev, int force_pio0) +{ + unsigned long xfer_mask; + int highbit; + + xfer_mask = ata_pack_xfermask(dev->pio_mask, dev->mwdma_mask, + dev->udma_mask); + + if (!xfer_mask) + goto fail; + /* don't gear down to MWDMA from UDMA, go directly to PIO */ + if (xfer_mask & ATA_MASK_UDMA) + xfer_mask &= ~ATA_MASK_MWDMA; + + highbit = fls(xfer_mask) - 1; + xfer_mask &= ~(1 << highbit); + if (force_pio0) + xfer_mask &= 1 << ATA_SHIFT_PIO; + if (!xfer_mask) + goto fail; + + ata_unpack_xfermask(xfer_mask, &dev->pio_mask, &dev->mwdma_mask, + &dev->udma_mask); + + ata_dev_printk(dev, KERN_WARNING, "limiting speed to %s\n", + ata_mode_string(xfer_mask)); + + return 0; + + fail: + return -EINVAL; +} + +static int ata_dev_set_mode(struct ata_device *dev) +{ + unsigned int err_mask; + int rc; + + dev->flags &= ~ATA_DFLAG_PIO; + if (dev->xfer_shift == ATA_SHIFT_PIO) + dev->flags |= ATA_DFLAG_PIO; + + err_mask = ata_dev_set_xfermode(dev); + if (err_mask) { + ata_dev_printk(dev, KERN_ERR, "failed to set xfermode " + "(err_mask=0x%x)\n", err_mask); + return -EIO; + } + + rc = ata_dev_revalidate(dev, 0); + if (rc) + return rc; + + DPRINTK("xfer_shift=%u, xfer_mode=0x%x\n", + dev->xfer_shift, (int)dev->xfer_mode); + + ata_dev_printk(dev, KERN_INFO, "configured for %s\n", + ata_mode_string(ata_xfer_mode2mask(dev->xfer_mode))); + return 0; +} + +/** + * ata_set_mode - Program timings and issue SET FEATURES - XFER + * @ap: port on which timings will be programmed + * @r_failed_dev: out paramter for failed device + * + * Set ATA device disk transfer mode (PIO3, UDMA6, etc.). If + * ata_set_mode() fails, pointer to the failing device is + * returned in @r_failed_dev. + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * 0 on success, negative errno otherwise + */ +int ata_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev) +{ + struct ata_device *dev; + int i, rc = 0, used_dma = 0, found = 0; + + /* has private set_mode? */ + if (ap->ops->set_mode) { + /* FIXME: make ->set_mode handle no device case and + * return error code and failing device on failure. + */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + if (ata_dev_ready(&ap->device[i])) { + ap->ops->set_mode(ap); + break; + } + } + return 0; + } + + /* step 1: calculate xfer_mask */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + unsigned int pio_mask, dma_mask; + + dev = &ap->device[i]; + + if (!ata_dev_enabled(dev)) + continue; + + ata_dev_xfermask(dev); + + pio_mask = ata_pack_xfermask(dev->pio_mask, 0, 0); + dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask); + dev->pio_mode = ata_xfer_mask2mode(pio_mask); + dev->dma_mode = ata_xfer_mask2mode(dma_mask); + + found = 1; + if (dev->dma_mode) + used_dma = 1; + } + if (!found) + goto out; + + /* step 2: always set host PIO timings */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + dev = &ap->device[i]; + if (!ata_dev_enabled(dev)) + continue; + + if (!dev->pio_mode) { + ata_dev_printk(dev, KERN_WARNING, "no PIO support\n"); + rc = -EINVAL; + goto out; + } + + dev->xfer_mode = dev->pio_mode; + dev->xfer_shift = ATA_SHIFT_PIO; + if (ap->ops->set_piomode) + ap->ops->set_piomode(ap, dev); + } + + /* step 3: set host DMA timings */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + dev = &ap->device[i]; + + if (!ata_dev_enabled(dev) || !dev->dma_mode) + continue; + + dev->xfer_mode = dev->dma_mode; + dev->xfer_shift = ata_xfer_mode2shift(dev->dma_mode); + if (ap->ops->set_dmamode) + ap->ops->set_dmamode(ap, dev); + } + + /* step 4: update devices' xfer mode */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + dev = &ap->device[i]; + + /* don't udpate suspended devices' xfer mode */ + if (!ata_dev_ready(dev)) + continue; + + rc = ata_dev_set_mode(dev); + if (rc) + goto out; + } + + /* Record simplex status. If we selected DMA then the other + * host channels are not permitted to do so. + */ + if (used_dma && (ap->host->flags & ATA_HOST_SIMPLEX)) + ap->host->simplex_claimed = 1; + + /* step5: chip specific finalisation */ + if (ap->ops->post_set_mode) + ap->ops->post_set_mode(ap); + + out: + if (rc) + *r_failed_dev = dev; + return rc; +} + +/** + * ata_tf_to_host - issue ATA taskfile to host controller + * @ap: port to which command is being issued + * @tf: ATA taskfile register set + * + * Issues ATA taskfile register set to ATA host controller, + * with proper synchronization with interrupt handler and + * other threads. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static inline void ata_tf_to_host(struct ata_port *ap, + const struct ata_taskfile *tf) +{ + ap->ops->tf_load(ap, tf); + ap->ops->exec_command(ap, tf); +} + +/** + * ata_busy_sleep - sleep until BSY clears, or timeout + * @ap: port containing status register to be polled + * @tmout_pat: impatience timeout + * @tmout: overall timeout + * + * Sleep until ATA Status register bit BSY clears, + * or a timeout occurs. + * + * LOCKING: None. + */ + +unsigned int ata_busy_sleep (struct ata_port *ap, + unsigned long tmout_pat, unsigned long tmout) +{ + unsigned long timer_start, timeout; + u8 status; + + status = ata_busy_wait(ap, ATA_BUSY, 300); + timer_start = jiffies; + timeout = timer_start + tmout_pat; + while ((status & ATA_BUSY) && (time_before(jiffies, timeout))) { + msleep(50); + status = ata_busy_wait(ap, ATA_BUSY, 3); + } + + if (status & ATA_BUSY) + ata_port_printk(ap, KERN_WARNING, + "port is slow to respond, please be patient\n"); + + timeout = timer_start + tmout; + while ((status & ATA_BUSY) && (time_before(jiffies, timeout))) { + msleep(50); + status = ata_chk_status(ap); + } + + if (status & ATA_BUSY) { + ata_port_printk(ap, KERN_ERR, "port failed to respond " + "(%lu secs)\n", tmout / HZ); + return 1; + } + + return 0; +} + +static void ata_bus_post_reset(struct ata_port *ap, unsigned int devmask) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int dev0 = devmask & (1 << 0); + unsigned int dev1 = devmask & (1 << 1); + unsigned long timeout; + + /* if device 0 was found in ata_devchk, wait for its + * BSY bit to clear + */ + if (dev0) + ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT); + + /* if device 1 was found in ata_devchk, wait for + * register access, then wait for BSY to clear + */ + timeout = jiffies + ATA_TMOUT_BOOT; + while (dev1) { + u8 nsect, lbal; + + ap->ops->dev_select(ap, 1); + if (ap->flags & ATA_FLAG_MMIO) { + nsect = readb((void __iomem *) ioaddr->nsect_addr); + lbal = readb((void __iomem *) ioaddr->lbal_addr); + } else { + nsect = inb(ioaddr->nsect_addr); + lbal = inb(ioaddr->lbal_addr); + } + if ((nsect == 1) && (lbal == 1)) + break; + if (time_after(jiffies, timeout)) { + dev1 = 0; + break; + } + msleep(50); /* give drive a breather */ + } + if (dev1) + ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT); + + /* is all this really necessary? */ + ap->ops->dev_select(ap, 0); + if (dev1) + ap->ops->dev_select(ap, 1); + if (dev0) + ap->ops->dev_select(ap, 0); +} + +static unsigned int ata_bus_softreset(struct ata_port *ap, + unsigned int devmask) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + + DPRINTK("ata%u: bus reset via SRST\n", ap->id); + + /* software reset. causes dev0 to be selected */ + if (ap->flags & ATA_FLAG_MMIO) { + writeb(ap->ctl, (void __iomem *) ioaddr->ctl_addr); + udelay(20); /* FIXME: flush */ + writeb(ap->ctl | ATA_SRST, (void __iomem *) ioaddr->ctl_addr); + udelay(20); /* FIXME: flush */ + writeb(ap->ctl, (void __iomem *) ioaddr->ctl_addr); + } else { + outb(ap->ctl, ioaddr->ctl_addr); + udelay(10); + outb(ap->ctl | ATA_SRST, ioaddr->ctl_addr); + udelay(10); + outb(ap->ctl, ioaddr->ctl_addr); + } + + /* spec mandates ">= 2ms" before checking status. + * We wait 150ms, because that was the magic delay used for + * ATAPI devices in Hale Landis's ATADRVR, for the period of time + * between when the ATA command register is written, and then + * status is checked. Because waiting for "a while" before + * checking status is fine, post SRST, we perform this magic + * delay here as well. + * + * Old drivers/ide uses the 2mS rule and then waits for ready + */ + msleep(150); + + /* Before we perform post reset processing we want to see if + * the bus shows 0xFF because the odd clown forgets the D7 + * pulldown resistor. + */ + if (ata_check_status(ap) == 0xFF) { + ata_port_printk(ap, KERN_ERR, "SRST failed (status 0xFF)\n"); + return AC_ERR_OTHER; + } + + ata_bus_post_reset(ap, devmask); + + return 0; +} + +/** + * ata_bus_reset - reset host port and associated ATA channel + * @ap: port to reset + * + * This is typically the first time we actually start issuing + * commands to the ATA channel. We wait for BSY to clear, then + * issue EXECUTE DEVICE DIAGNOSTIC command, polling for its + * result. Determine what devices, if any, are on the channel + * by looking at the device 0/1 error register. Look at the signature + * stored in each device's taskfile registers, to determine if + * the device is ATA or ATAPI. + * + * LOCKING: + * PCI/etc. bus probe sem. + * Obtains host lock. + * + * SIDE EFFECTS: + * Sets ATA_FLAG_DISABLED if bus reset fails. + */ + +void ata_bus_reset(struct ata_port *ap) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS; + u8 err; + unsigned int dev0, dev1 = 0, devmask = 0; + + DPRINTK("ENTER, host %u, port %u\n", ap->id, ap->port_no); + + /* determine if device 0/1 are present */ + if (ap->flags & ATA_FLAG_SATA_RESET) + dev0 = 1; + else { + dev0 = ata_devchk(ap, 0); + if (slave_possible) + dev1 = ata_devchk(ap, 1); + } + + if (dev0) + devmask |= (1 << 0); + if (dev1) + devmask |= (1 << 1); + + /* select device 0 again */ + ap->ops->dev_select(ap, 0); + + /* issue bus reset */ + if (ap->flags & ATA_FLAG_SRST) + if (ata_bus_softreset(ap, devmask)) + goto err_out; + + /* + * determine by signature whether we have ATA or ATAPI devices + */ + ap->device[0].class = ata_dev_try_classify(ap, 0, &err); + if ((slave_possible) && (err != 0x81)) + ap->device[1].class = ata_dev_try_classify(ap, 1, &err); + + /* re-enable interrupts */ + if (ap->ioaddr.ctl_addr) /* FIXME: hack. create a hook instead */ + ata_irq_on(ap); + + /* is double-select really necessary? */ + if (ap->device[1].class != ATA_DEV_NONE) + ap->ops->dev_select(ap, 1); + if (ap->device[0].class != ATA_DEV_NONE) + ap->ops->dev_select(ap, 0); + + /* if no devices were detected, disable this port */ + if ((ap->device[0].class == ATA_DEV_NONE) && + (ap->device[1].class == ATA_DEV_NONE)) + goto err_out; + + if (ap->flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST)) { + /* set up device control for ATA_FLAG_SATA_RESET */ + if (ap->flags & ATA_FLAG_MMIO) + writeb(ap->ctl, (void __iomem *) ioaddr->ctl_addr); + else + outb(ap->ctl, ioaddr->ctl_addr); + } + + DPRINTK("EXIT\n"); + return; + +err_out: + ata_port_printk(ap, KERN_ERR, "disabling port\n"); + ap->ops->port_disable(ap); + + DPRINTK("EXIT\n"); +} + +/** + * sata_phy_debounce - debounce SATA phy status + * @ap: ATA port to debounce SATA phy status for + * @params: timing parameters { interval, duratinon, timeout } in msec + * + * Make sure SStatus of @ap reaches stable state, determined by + * holding the same value where DET is not 1 for @duration polled + * every @interval, before @timeout. Timeout constraints the + * beginning of the stable state. Because, after hot unplugging, + * DET gets stuck at 1 on some controllers, this functions waits + * until timeout then returns 0 if DET is stable at 1. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno on failure. + */ +int sata_phy_debounce(struct ata_port *ap, const unsigned long *params) +{ + unsigned long interval_msec = params[0]; + unsigned long duration = params[1] * HZ / 1000; + unsigned long timeout = jiffies + params[2] * HZ / 1000; + unsigned long last_jiffies; + u32 last, cur; + int rc; + + if ((rc = sata_scr_read(ap, SCR_STATUS, &cur))) + return rc; + cur &= 0xf; + + last = cur; + last_jiffies = jiffies; + + while (1) { + msleep(interval_msec); + if ((rc = sata_scr_read(ap, SCR_STATUS, &cur))) + return rc; + cur &= 0xf; + + /* DET stable? */ + if (cur == last) { + if (cur == 1 && time_before(jiffies, timeout)) + continue; + if (time_after(jiffies, last_jiffies + duration)) + return 0; + continue; + } + + /* unstable, start over */ + last = cur; + last_jiffies = jiffies; + + /* check timeout */ + if (time_after(jiffies, timeout)) + return -EBUSY; + } +} + +/** + * sata_phy_resume - resume SATA phy + * @ap: ATA port to resume SATA phy for + * @params: timing parameters { interval, duratinon, timeout } in msec + * + * Resume SATA phy of @ap and debounce it. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno on failure. + */ +int sata_phy_resume(struct ata_port *ap, const unsigned long *params) +{ + u32 scontrol; + int rc; + + if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + return rc; + + scontrol = (scontrol & 0x0f0) | 0x300; + + if ((rc = sata_scr_write(ap, SCR_CONTROL, scontrol))) + return rc; + + /* Some PHYs react badly if SStatus is pounded immediately + * after resuming. Delay 200ms before debouncing. + */ + msleep(200); + + return sata_phy_debounce(ap, params); +} + +static void ata_wait_spinup(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + unsigned long end, secs; + int rc; + + /* first, debounce phy if SATA */ + if (ap->cbl == ATA_CBL_SATA) { + rc = sata_phy_debounce(ap, sata_deb_timing_hotplug); + + /* if debounced successfully and offline, no need to wait */ + if ((rc == 0 || rc == -EOPNOTSUPP) && ata_port_offline(ap)) + return; + } + + /* okay, let's give the drive time to spin up */ + end = ehc->i.hotplug_timestamp + ATA_SPINUP_WAIT * HZ / 1000; + secs = ((end - jiffies) + HZ - 1) / HZ; + + if (time_after(jiffies, end)) + return; + + if (secs > 5) + ata_port_printk(ap, KERN_INFO, "waiting for device to spin up " + "(%lu secs)\n", secs); + + schedule_timeout_uninterruptible(end - jiffies); +} + +/** + * ata_std_prereset - prepare for reset + * @ap: ATA port to be reset + * + * @ap is about to be reset. Initialize it. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +int ata_std_prereset(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + const unsigned long *timing = sata_ehc_deb_timing(ehc); + int rc; + + /* handle link resume & hotplug spinup */ + if ((ehc->i.flags & ATA_EHI_RESUME_LINK) && + (ap->flags & ATA_FLAG_HRST_TO_RESUME)) + ehc->i.action |= ATA_EH_HARDRESET; + + if ((ehc->i.flags & ATA_EHI_HOTPLUGGED) && + (ap->flags & ATA_FLAG_SKIP_D2H_BSY)) + ata_wait_spinup(ap); + + /* if we're about to do hardreset, nothing more to do */ + if (ehc->i.action & ATA_EH_HARDRESET) + return 0; + + /* if SATA, resume phy */ + if (ap->cbl == ATA_CBL_SATA) { + rc = sata_phy_resume(ap, timing); + if (rc && rc != -EOPNOTSUPP) { + /* phy resume failed */ + ata_port_printk(ap, KERN_WARNING, "failed to resume " + "link for reset (errno=%d)\n", rc); + return rc; + } + } + + /* Wait for !BSY if the controller can wait for the first D2H + * Reg FIS and we don't know that no device is attached. + */ + if (!(ap->flags & ATA_FLAG_SKIP_D2H_BSY) && !ata_port_offline(ap)) + ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT); + + return 0; +} + +/** + * ata_std_softreset - reset host port via ATA SRST + * @ap: port to reset + * @classes: resulting classes of attached devices + * + * Reset host port using ATA SRST. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +int ata_std_softreset(struct ata_port *ap, unsigned int *classes) +{ + unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS; + unsigned int devmask = 0, err_mask; + u8 err; + + DPRINTK("ENTER\n"); + + if (ata_port_offline(ap)) { + classes[0] = ATA_DEV_NONE; + goto out; + } + + /* determine if device 0/1 are present */ + if (ata_devchk(ap, 0)) + devmask |= (1 << 0); + if (slave_possible && ata_devchk(ap, 1)) + devmask |= (1 << 1); + + /* select device 0 again */ + ap->ops->dev_select(ap, 0); + + /* issue bus reset */ + DPRINTK("about to softreset, devmask=%x\n", devmask); + err_mask = ata_bus_softreset(ap, devmask); + if (err_mask) { + ata_port_printk(ap, KERN_ERR, "SRST failed (err_mask=0x%x)\n", + err_mask); + return -EIO; + } + + /* determine by signature whether we have ATA or ATAPI devices */ + classes[0] = ata_dev_try_classify(ap, 0, &err); + if (slave_possible && err != 0x81) + classes[1] = ata_dev_try_classify(ap, 1, &err); + + out: + DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]); + return 0; +} + +/** + * sata_std_hardreset - reset host port via SATA phy reset + * @ap: port to reset + * @class: resulting class of attached device + * + * SATA phy-reset host port using DET bits of SControl register. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +int sata_std_hardreset(struct ata_port *ap, unsigned int *class) +{ + struct ata_eh_context *ehc = &ap->eh_context; + const unsigned long *timing = sata_ehc_deb_timing(ehc); + u32 scontrol; + int rc; + + DPRINTK("ENTER\n"); + + if (sata_set_spd_needed(ap)) { + /* SATA spec says nothing about how to reconfigure + * spd. To be on the safe side, turn off phy during + * reconfiguration. This works for at least ICH7 AHCI + * and Sil3124. + */ + if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + return rc; + + scontrol = (scontrol & 0x0f0) | 0x304; + + if ((rc = sata_scr_write(ap, SCR_CONTROL, scontrol))) + return rc; + + sata_set_spd(ap); + } + + /* issue phy wake/reset */ + if ((rc = sata_scr_read(ap, SCR_CONTROL, &scontrol))) + return rc; + + scontrol = (scontrol & 0x0f0) | 0x301; + + if ((rc = sata_scr_write_flush(ap, SCR_CONTROL, scontrol))) + return rc; + + /* Couldn't find anything in SATA I/II specs, but AHCI-1.1 + * 10.4.2 says at least 1 ms. + */ + msleep(1); + + /* bring phy back */ + sata_phy_resume(ap, timing); + + /* TODO: phy layer with polling, timeouts, etc. */ + if (ata_port_offline(ap)) { + *class = ATA_DEV_NONE; + DPRINTK("EXIT, link offline\n"); + return 0; + } + + if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) { + ata_port_printk(ap, KERN_ERR, + "COMRESET failed (device not ready)\n"); + return -EIO; + } + + ap->ops->dev_select(ap, 0); /* probably unnecessary */ + + *class = ata_dev_try_classify(ap, 0, NULL); + + DPRINTK("EXIT, class=%u\n", *class); + return 0; +} + +/** + * ata_std_postreset - standard postreset callback + * @ap: the target ata_port + * @classes: classes of attached devices + * + * This function is invoked after a successful reset. Note that + * the device might have been reset more than once using + * different reset methods before postreset is invoked. + * + * LOCKING: + * Kernel thread context (may sleep) + */ +void ata_std_postreset(struct ata_port *ap, unsigned int *classes) +{ + u32 serror; + + DPRINTK("ENTER\n"); + + /* print link status */ + sata_print_link_status(ap); + + /* clear SError */ + if (sata_scr_read(ap, SCR_ERROR, &serror) == 0) + sata_scr_write(ap, SCR_ERROR, serror); + + /* re-enable interrupts */ + if (!ap->ops->error_handler) { + /* FIXME: hack. create a hook instead */ + if (ap->ioaddr.ctl_addr) + ata_irq_on(ap); + } + + /* is double-select really necessary? */ + if (classes[0] != ATA_DEV_NONE) + ap->ops->dev_select(ap, 1); + if (classes[1] != ATA_DEV_NONE) + ap->ops->dev_select(ap, 0); + + /* bail out if no device is present */ + if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) { + DPRINTK("EXIT, no device\n"); + return; + } + + /* set up device control */ + if (ap->ioaddr.ctl_addr) { + if (ap->flags & ATA_FLAG_MMIO) + writeb(ap->ctl, (void __iomem *) ap->ioaddr.ctl_addr); + else + outb(ap->ctl, ap->ioaddr.ctl_addr); + } + + DPRINTK("EXIT\n"); +} + +/** + * ata_dev_same_device - Determine whether new ID matches configured device + * @dev: device to compare against + * @new_class: class of the new device + * @new_id: IDENTIFY page of the new device + * + * Compare @new_class and @new_id against @dev and determine + * whether @dev is the device indicated by @new_class and + * @new_id. + * + * LOCKING: + * None. + * + * RETURNS: + * 1 if @dev matches @new_class and @new_id, 0 otherwise. + */ +static int ata_dev_same_device(struct ata_device *dev, unsigned int new_class, + const u16 *new_id) +{ + const u16 *old_id = dev->id; + unsigned char model[2][41], serial[2][21]; + u64 new_n_sectors; + + if (dev->class != new_class) { + ata_dev_printk(dev, KERN_INFO, "class mismatch %d != %d\n", + dev->class, new_class); + return 0; + } + + ata_id_c_string(old_id, model[0], ATA_ID_PROD_OFS, sizeof(model[0])); + ata_id_c_string(new_id, model[1], ATA_ID_PROD_OFS, sizeof(model[1])); + ata_id_c_string(old_id, serial[0], ATA_ID_SERNO_OFS, sizeof(serial[0])); + ata_id_c_string(new_id, serial[1], ATA_ID_SERNO_OFS, sizeof(serial[1])); + new_n_sectors = ata_id_n_sectors(new_id); + + if (strcmp(model[0], model[1])) { + ata_dev_printk(dev, KERN_INFO, "model number mismatch " + "'%s' != '%s'\n", model[0], model[1]); + return 0; + } + + if (strcmp(serial[0], serial[1])) { + ata_dev_printk(dev, KERN_INFO, "serial number mismatch " + "'%s' != '%s'\n", serial[0], serial[1]); + return 0; + } + + if (dev->class == ATA_DEV_ATA && dev->n_sectors != new_n_sectors) { + ata_dev_printk(dev, KERN_INFO, "n_sectors mismatch " + "%llu != %llu\n", + (unsigned long long)dev->n_sectors, + (unsigned long long)new_n_sectors); + return 0; + } + + return 1; +} + +/** + * ata_dev_revalidate - Revalidate ATA device + * @dev: device to revalidate + * @post_reset: is this revalidation after reset? + * + * Re-read IDENTIFY page and make sure @dev is still attached to + * the port. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, negative errno otherwise + */ +int ata_dev_revalidate(struct ata_device *dev, int post_reset) +{ + unsigned int class = dev->class; + u16 *id = (void *)dev->ap->sector_buf; + int rc; + + if (!ata_dev_enabled(dev)) { + rc = -ENODEV; + goto fail; + } + + /* read ID data */ + rc = ata_dev_read_id(dev, &class, post_reset, id); + if (rc) + goto fail; + + /* is the device still there? */ + if (!ata_dev_same_device(dev, class, id)) { + rc = -ENODEV; + goto fail; + } + + memcpy(dev->id, id, sizeof(id[0]) * ATA_ID_WORDS); + + /* configure device according to the new ID */ + rc = ata_dev_configure(dev, 0); + if (rc == 0) + return 0; + + fail: + ata_dev_printk(dev, KERN_ERR, "revalidation failed (errno=%d)\n", rc); + return rc; +} + +static const char * const ata_dma_blacklist [] = { + "WDC AC11000H", NULL, + "WDC AC22100H", NULL, + "WDC AC32500H", NULL, + "WDC AC33100H", NULL, + "WDC AC31600H", NULL, + "WDC AC32100H", "24.09P07", + "WDC AC23200L", "21.10N21", + "Compaq CRD-8241B", NULL, + "CRD-8400B", NULL, + "CRD-8480B", NULL, + "CRD-8482B", NULL, + "CRD-84", NULL, + "SanDisk SDP3B", NULL, + "SanDisk SDP3B-64", NULL, + "SANYO CD-ROM CRD", NULL, + "HITACHI CDR-8", NULL, + "HITACHI CDR-8335", NULL, + "HITACHI CDR-8435", NULL, + "Toshiba CD-ROM XM-6202B", NULL, + "TOSHIBA CD-ROM XM-1702BC", NULL, + "CD-532E-A", NULL, + "E-IDE CD-ROM CR-840", NULL, + "CD-ROM Drive/F5A", NULL, + "WPI CDD-820", NULL, + "SAMSUNG CD-ROM SC-148C", NULL, + "SAMSUNG CD-ROM SC", NULL, + "SanDisk SDP3B-64", NULL, + "ATAPI CD-ROM DRIVE 40X MAXIMUM",NULL, + "_NEC DV5800A", NULL, + "SAMSUNG CD-ROM SN-124", "N001" +}; + +static int ata_strim(char *s, size_t len) +{ + len = strnlen(s, len); + + /* ATAPI specifies that empty space is blank-filled; remove blanks */ + while ((len > 0) && (s[len - 1] == ' ')) { + len--; + s[len] = 0; + } + return len; +} + +static int ata_dma_blacklisted(const struct ata_device *dev) +{ + unsigned char model_num[40]; + unsigned char model_rev[16]; + unsigned int nlen, rlen; + int i; + + /* We don't support polling DMA. + * DMA blacklist those ATAPI devices with CDB-intr (and use PIO) + * if the LLDD handles only interrupts in the HSM_ST_LAST state. + */ + if ((dev->ap->flags & ATA_FLAG_PIO_POLLING) && + (dev->flags & ATA_DFLAG_CDB_INTR)) + return 1; + + ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS, + sizeof(model_num)); + ata_id_string(dev->id, model_rev, ATA_ID_FW_REV_OFS, + sizeof(model_rev)); + nlen = ata_strim(model_num, sizeof(model_num)); + rlen = ata_strim(model_rev, sizeof(model_rev)); + + for (i = 0; i < ARRAY_SIZE(ata_dma_blacklist); i += 2) { + if (!strncmp(ata_dma_blacklist[i], model_num, nlen)) { + if (ata_dma_blacklist[i+1] == NULL) + return 1; + if (!strncmp(ata_dma_blacklist[i], model_rev, rlen)) + return 1; + } + } + return 0; +} + +/** + * ata_dev_xfermask - Compute supported xfermask of the given device + * @dev: Device to compute xfermask for + * + * Compute supported xfermask of @dev and store it in + * dev->*_mask. This function is responsible for applying all + * known limits including host controller limits, device + * blacklist, etc... + * + * LOCKING: + * None. + */ +static void ata_dev_xfermask(struct ata_device *dev) +{ + struct ata_port *ap = dev->ap; + struct ata_host *host = ap->host; + unsigned long xfer_mask; + + /* controller modes available */ + xfer_mask = ata_pack_xfermask(ap->pio_mask, + ap->mwdma_mask, ap->udma_mask); + + /* Apply cable rule here. Don't apply it early because when + * we handle hot plug the cable type can itself change. + */ + if (ap->cbl == ATA_CBL_PATA40) + xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA); + + xfer_mask &= ata_pack_xfermask(dev->pio_mask, + dev->mwdma_mask, dev->udma_mask); + xfer_mask &= ata_id_xfermask(dev->id); + + /* + * CFA Advanced TrueIDE timings are not allowed on a shared + * cable + */ + if (ata_dev_pair(dev)) { + /* No PIO5 or PIO6 */ + xfer_mask &= ~(0x03 << (ATA_SHIFT_PIO + 5)); + /* No MWDMA3 or MWDMA 4 */ + xfer_mask &= ~(0x03 << (ATA_SHIFT_MWDMA + 3)); + } + + if (ata_dma_blacklisted(dev)) { + xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); + ata_dev_printk(dev, KERN_WARNING, + "device is on DMA blacklist, disabling DMA\n"); + } + + if ((host->flags & ATA_HOST_SIMPLEX) && host->simplex_claimed) { + xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); + ata_dev_printk(dev, KERN_WARNING, "simplex DMA is claimed by " + "other device, disabling DMA\n"); + } + + if (ap->ops->mode_filter) + xfer_mask = ap->ops->mode_filter(ap, dev, xfer_mask); + + ata_unpack_xfermask(xfer_mask, &dev->pio_mask, + &dev->mwdma_mask, &dev->udma_mask); +} + +/** + * ata_dev_set_xfermode - Issue SET FEATURES - XFER MODE command + * @dev: Device to which command will be sent + * + * Issue SET FEATURES - XFER MODE command to device @dev + * on port @ap. + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * 0 on success, AC_ERR_* mask otherwise. + */ + +static unsigned int ata_dev_set_xfermode(struct ata_device *dev) +{ + struct ata_taskfile tf; + unsigned int err_mask; + + /* set up set-features taskfile */ + DPRINTK("set features - xfer mode\n"); + + ata_tf_init(dev, &tf); + tf.command = ATA_CMD_SET_FEATURES; + tf.feature = SETFEATURES_XFER; + tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + tf.protocol = ATA_PROT_NODATA; + tf.nsect = dev->xfer_mode; + + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); + + DPRINTK("EXIT, err_mask=%x\n", err_mask); + return err_mask; +} + +/** + * ata_dev_init_params - Issue INIT DEV PARAMS command + * @dev: Device to which command will be sent + * @heads: Number of heads (taskfile parameter) + * @sectors: Number of sectors (taskfile parameter) + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, AC_ERR_* mask otherwise. + */ +static unsigned int ata_dev_init_params(struct ata_device *dev, + u16 heads, u16 sectors) +{ + struct ata_taskfile tf; + unsigned int err_mask; + + /* Number of sectors per track 1-255. Number of heads 1-16 */ + if (sectors < 1 || sectors > 255 || heads < 1 || heads > 16) + return AC_ERR_INVALID; + + /* set up init dev params taskfile */ + DPRINTK("init dev params \n"); + + ata_tf_init(dev, &tf); + tf.command = ATA_CMD_INIT_DEV_PARAMS; + tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + tf.protocol = ATA_PROT_NODATA; + tf.nsect = sectors; + tf.device |= (heads - 1) & 0x0f; /* max head = num. of heads - 1 */ + + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0); + + DPRINTK("EXIT, err_mask=%x\n", err_mask); + return err_mask; +} + +/** + * ata_sg_clean - Unmap DMA memory associated with command + * @qc: Command containing DMA memory to be released + * + * Unmap all mapped DMA memory associated with this command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void ata_sg_clean(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct scatterlist *sg = qc->__sg; + int dir = qc->dma_dir; + void *pad_buf = NULL; + + WARN_ON(!(qc->flags & ATA_QCFLAG_DMAMAP)); + WARN_ON(sg == NULL); + + if (qc->flags & ATA_QCFLAG_SINGLE) + WARN_ON(qc->n_elem > 1); + + VPRINTK("unmapping %u sg elements\n", qc->n_elem); + + /* if we padded the buffer out to 32-bit bound, and data + * xfer direction is from-device, we must copy from the + * pad buffer back into the supplied buffer + */ + if (qc->pad_len && !(qc->tf.flags & ATA_TFLAG_WRITE)) + pad_buf = ap->pad + (qc->tag * ATA_DMA_PAD_SZ); + + if (qc->flags & ATA_QCFLAG_SG) { + if (qc->n_elem) + dma_unmap_sg(ap->dev, sg, qc->n_elem, dir); + /* restore last sg */ + sg[qc->orig_n_elem - 1].length += qc->pad_len; + if (pad_buf) { + struct scatterlist *psg = &qc->pad_sgent; + void *addr = kmap_atomic(psg->page, KM_IRQ0); + memcpy(addr + psg->offset, pad_buf, qc->pad_len); + kunmap_atomic(addr, KM_IRQ0); + } + } else { + if (qc->n_elem) + dma_unmap_single(ap->dev, + sg_dma_address(&sg[0]), sg_dma_len(&sg[0]), + dir); + /* restore sg */ + sg->length += qc->pad_len; + if (pad_buf) + memcpy(qc->buf_virt + sg->length - qc->pad_len, + pad_buf, qc->pad_len); + } + + qc->flags &= ~ATA_QCFLAG_DMAMAP; + qc->__sg = NULL; +} + +/** + * ata_fill_sg - Fill PCI IDE PRD table + * @qc: Metadata associated with taskfile to be transferred + * + * Fill PCI IDE PRD (scatter-gather) table with segments + * associated with the current disk command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + */ +static void ata_fill_sg(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct scatterlist *sg; + unsigned int idx; + + WARN_ON(qc->__sg == NULL); + WARN_ON(qc->n_elem == 0 && qc->pad_len == 0); + + idx = 0; + ata_for_each_sg(sg, qc) { + u32 addr, offset; + u32 sg_len, len; + + /* determine if physical DMA addr spans 64K boundary. + * Note h/w doesn't support 64-bit, so we unconditionally + * truncate dma_addr_t to u32. + */ + addr = (u32) sg_dma_address(sg); + sg_len = sg_dma_len(sg); + + while (sg_len) { + offset = addr & 0xffff; + len = sg_len; + if ((offset + sg_len) > 0x10000) + len = 0x10000 - offset; + + ap->prd[idx].addr = cpu_to_le32(addr); + ap->prd[idx].flags_len = cpu_to_le32(len & 0xffff); + VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len); + + idx++; + sg_len -= len; + addr += len; + } + } + + if (idx) + ap->prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT); +} +/** + * ata_check_atapi_dma - Check whether ATAPI DMA can be supported + * @qc: Metadata associated with taskfile to check + * + * Allow low-level driver to filter ATA PACKET commands, returning + * a status indicating whether or not it is OK to use DMA for the + * supplied PACKET command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: 0 when ATAPI DMA can be used + * nonzero otherwise + */ +int ata_check_atapi_dma(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + int rc = 0; /* Assume ATAPI DMA is OK by default */ + + if (ap->ops->check_atapi_dma) + rc = ap->ops->check_atapi_dma(qc); + + return rc; +} +/** + * ata_qc_prep - Prepare taskfile for submission + * @qc: Metadata associated with taskfile to be prepared + * + * Prepare ATA taskfile for submission. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_qc_prep(struct ata_queued_cmd *qc) +{ + if (!(qc->flags & ATA_QCFLAG_DMAMAP)) + return; + + ata_fill_sg(qc); +} + +void ata_noop_qc_prep(struct ata_queued_cmd *qc) { } + +/** + * ata_sg_init_one - Associate command with memory buffer + * @qc: Command to be associated + * @buf: Memory buffer + * @buflen: Length of memory buffer, in bytes. + * + * Initialize the data-related elements of queued_cmd @qc + * to point to a single memory buffer, @buf of byte length @buflen. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +void ata_sg_init_one(struct ata_queued_cmd *qc, void *buf, unsigned int buflen) +{ + struct scatterlist *sg; + + qc->flags |= ATA_QCFLAG_SINGLE; + + memset(&qc->sgent, 0, sizeof(qc->sgent)); + qc->__sg = &qc->sgent; + qc->n_elem = 1; + qc->orig_n_elem = 1; + qc->buf_virt = buf; + qc->nbytes = buflen; + + sg = qc->__sg; + sg_init_one(sg, buf, buflen); +} + +/** + * ata_sg_init - Associate command with scatter-gather table. + * @qc: Command to be associated + * @sg: Scatter-gather table. + * @n_elem: Number of elements in s/g table. + * + * Initialize the data-related elements of queued_cmd @qc + * to point to a scatter-gather table @sg, containing @n_elem + * elements. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg, + unsigned int n_elem) +{ + qc->flags |= ATA_QCFLAG_SG; + qc->__sg = sg; + qc->n_elem = n_elem; + qc->orig_n_elem = n_elem; +} + +/** + * ata_sg_setup_one - DMA-map the memory buffer associated with a command. + * @qc: Command with memory buffer to be mapped. + * + * DMA-map the memory buffer associated with queued_cmd @qc. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, negative on error. + */ + +static int ata_sg_setup_one(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + int dir = qc->dma_dir; + struct scatterlist *sg = qc->__sg; + dma_addr_t dma_address; + int trim_sg = 0; + + /* we must lengthen transfers to end on a 32-bit boundary */ + qc->pad_len = sg->length & 3; + if (qc->pad_len) { + void *pad_buf = ap->pad + (qc->tag * ATA_DMA_PAD_SZ); + struct scatterlist *psg = &qc->pad_sgent; + + WARN_ON(qc->dev->class != ATA_DEV_ATAPI); + + memset(pad_buf, 0, ATA_DMA_PAD_SZ); + + if (qc->tf.flags & ATA_TFLAG_WRITE) + memcpy(pad_buf, qc->buf_virt + sg->length - qc->pad_len, + qc->pad_len); + + sg_dma_address(psg) = ap->pad_dma + (qc->tag * ATA_DMA_PAD_SZ); + sg_dma_len(psg) = ATA_DMA_PAD_SZ; + /* trim sg */ + sg->length -= qc->pad_len; + if (sg->length == 0) + trim_sg = 1; + + DPRINTK("padding done, sg->length=%u pad_len=%u\n", + sg->length, qc->pad_len); + } + + if (trim_sg) { + qc->n_elem--; + goto skip_map; + } + + dma_address = dma_map_single(ap->dev, qc->buf_virt, + sg->length, dir); + if (dma_mapping_error(dma_address)) { + /* restore sg */ + sg->length += qc->pad_len; + return -1; + } + + sg_dma_address(sg) = dma_address; + sg_dma_len(sg) = sg->length; + +skip_map: + DPRINTK("mapped buffer of %d bytes for %s\n", sg_dma_len(sg), + qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read"); + + return 0; +} + +/** + * ata_sg_setup - DMA-map the scatter-gather table associated with a command. + * @qc: Command with scatter-gather table to be mapped. + * + * DMA-map the scatter-gather table associated with queued_cmd @qc. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, negative on error. + * + */ + +static int ata_sg_setup(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct scatterlist *sg = qc->__sg; + struct scatterlist *lsg = &sg[qc->n_elem - 1]; + int n_elem, pre_n_elem, dir, trim_sg = 0; + + VPRINTK("ENTER, ata%u\n", ap->id); + WARN_ON(!(qc->flags & ATA_QCFLAG_SG)); + + /* we must lengthen transfers to end on a 32-bit boundary */ + qc->pad_len = lsg->length & 3; + if (qc->pad_len) { + void *pad_buf = ap->pad + (qc->tag * ATA_DMA_PAD_SZ); + struct scatterlist *psg = &qc->pad_sgent; + unsigned int offset; + + WARN_ON(qc->dev->class != ATA_DEV_ATAPI); + + memset(pad_buf, 0, ATA_DMA_PAD_SZ); + + /* + * psg->page/offset are used to copy to-be-written + * data in this function or read data in ata_sg_clean. + */ + offset = lsg->offset + lsg->length - qc->pad_len; + psg->page = nth_page(lsg->page, offset >> PAGE_SHIFT); + psg->offset = offset_in_page(offset); + + if (qc->tf.flags & ATA_TFLAG_WRITE) { + void *addr = kmap_atomic(psg->page, KM_IRQ0); + memcpy(pad_buf, addr + psg->offset, qc->pad_len); + kunmap_atomic(addr, KM_IRQ0); + } + + sg_dma_address(psg) = ap->pad_dma + (qc->tag * ATA_DMA_PAD_SZ); + sg_dma_len(psg) = ATA_DMA_PAD_SZ; + /* trim last sg */ + lsg->length -= qc->pad_len; + if (lsg->length == 0) + trim_sg = 1; + + DPRINTK("padding done, sg[%d].length=%u pad_len=%u\n", + qc->n_elem - 1, lsg->length, qc->pad_len); + } + + pre_n_elem = qc->n_elem; + if (trim_sg && pre_n_elem) + pre_n_elem--; + + if (!pre_n_elem) { + n_elem = 0; + goto skip_map; + } + + dir = qc->dma_dir; + n_elem = dma_map_sg(ap->dev, sg, pre_n_elem, dir); + if (n_elem < 1) { + /* restore last sg */ + lsg->length += qc->pad_len; + return -1; + } + + DPRINTK("%d sg elements mapped\n", n_elem); + +skip_map: + qc->n_elem = n_elem; + + return 0; +} + +/** + * swap_buf_le16 - swap halves of 16-bit words in place + * @buf: Buffer to swap + * @buf_words: Number of 16-bit words in buffer. + * + * Swap halves of 16-bit words if needed to convert from + * little-endian byte order to native cpu byte order, or + * vice-versa. + * + * LOCKING: + * Inherited from caller. + */ +void swap_buf_le16(u16 *buf, unsigned int buf_words) +{ +#ifdef __BIG_ENDIAN + unsigned int i; + + for (i = 0; i < buf_words; i++) + buf[i] = le16_to_cpu(buf[i]); +#endif /* __BIG_ENDIAN */ +} + +/** + * ata_mmio_data_xfer - Transfer data by MMIO + * @adev: device for this I/O + * @buf: data buffer + * @buflen: buffer length + * @write_data: read/write + * + * Transfer data from/to the device data register by MMIO. + * + * LOCKING: + * Inherited from caller. + */ + +void ata_mmio_data_xfer(struct ata_device *adev, unsigned char *buf, + unsigned int buflen, int write_data) +{ + struct ata_port *ap = adev->ap; + unsigned int i; + unsigned int words = buflen >> 1; + u16 *buf16 = (u16 *) buf; + void __iomem *mmio = (void __iomem *)ap->ioaddr.data_addr; + + /* Transfer multiple of 2 bytes */ + if (write_data) { + for (i = 0; i < words; i++) + writew(le16_to_cpu(buf16[i]), mmio); + } else { + for (i = 0; i < words; i++) + buf16[i] = cpu_to_le16(readw(mmio)); + } + + /* Transfer trailing 1 byte, if any. */ + if (unlikely(buflen & 0x01)) { + u16 align_buf[1] = { 0 }; + unsigned char *trailing_buf = buf + buflen - 1; + + if (write_data) { + memcpy(align_buf, trailing_buf, 1); + writew(le16_to_cpu(align_buf[0]), mmio); + } else { + align_buf[0] = cpu_to_le16(readw(mmio)); + memcpy(trailing_buf, align_buf, 1); + } + } +} + +/** + * ata_pio_data_xfer - Transfer data by PIO + * @adev: device to target + * @buf: data buffer + * @buflen: buffer length + * @write_data: read/write + * + * Transfer data from/to the device data register by PIO. + * + * LOCKING: + * Inherited from caller. + */ + +void ata_pio_data_xfer(struct ata_device *adev, unsigned char *buf, + unsigned int buflen, int write_data) +{ + struct ata_port *ap = adev->ap; + unsigned int words = buflen >> 1; + + /* Transfer multiple of 2 bytes */ + if (write_data) + outsw(ap->ioaddr.data_addr, buf, words); + else + insw(ap->ioaddr.data_addr, buf, words); + + /* Transfer trailing 1 byte, if any. */ + if (unlikely(buflen & 0x01)) { + u16 align_buf[1] = { 0 }; + unsigned char *trailing_buf = buf + buflen - 1; + + if (write_data) { + memcpy(align_buf, trailing_buf, 1); + outw(le16_to_cpu(align_buf[0]), ap->ioaddr.data_addr); + } else { + align_buf[0] = cpu_to_le16(inw(ap->ioaddr.data_addr)); + memcpy(trailing_buf, align_buf, 1); + } + } +} + +/** + * ata_pio_data_xfer_noirq - Transfer data by PIO + * @adev: device to target + * @buf: data buffer + * @buflen: buffer length + * @write_data: read/write + * + * Transfer data from/to the device data register by PIO. Do the + * transfer with interrupts disabled. + * + * LOCKING: + * Inherited from caller. + */ + +void ata_pio_data_xfer_noirq(struct ata_device *adev, unsigned char *buf, + unsigned int buflen, int write_data) +{ + unsigned long flags; + local_irq_save(flags); + ata_pio_data_xfer(adev, buf, buflen, write_data); + local_irq_restore(flags); +} + + +/** + * ata_pio_sector - Transfer ATA_SECT_SIZE (512 bytes) of data. + * @qc: Command on going + * + * Transfer ATA_SECT_SIZE of data from/to the ATA device. + * + * LOCKING: + * Inherited from caller. + */ + +static void ata_pio_sector(struct ata_queued_cmd *qc) +{ + int do_write = (qc->tf.flags & ATA_TFLAG_WRITE); + struct scatterlist *sg = qc->__sg; + struct ata_port *ap = qc->ap; + struct page *page; + unsigned int offset; + unsigned char *buf; + + if (qc->cursect == (qc->nsect - 1)) + ap->hsm_task_state = HSM_ST_LAST; + + page = sg[qc->cursg].page; + offset = sg[qc->cursg].offset + qc->cursg_ofs * ATA_SECT_SIZE; + + /* get the current page and offset */ + page = nth_page(page, (offset >> PAGE_SHIFT)); + offset %= PAGE_SIZE; + + DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read"); + + if (PageHighMem(page)) { + unsigned long flags; + + /* FIXME: use a bounce buffer */ + local_irq_save(flags); + buf = kmap_atomic(page, KM_IRQ0); + + /* do the actual data transfer */ + ap->ops->data_xfer(qc->dev, buf + offset, ATA_SECT_SIZE, do_write); + + kunmap_atomic(buf, KM_IRQ0); + local_irq_restore(flags); + } else { + buf = page_address(page); + ap->ops->data_xfer(qc->dev, buf + offset, ATA_SECT_SIZE, do_write); + } + + qc->cursect++; + qc->cursg_ofs++; + + if ((qc->cursg_ofs * ATA_SECT_SIZE) == (&sg[qc->cursg])->length) { + qc->cursg++; + qc->cursg_ofs = 0; + } +} + +/** + * ata_pio_sectors - Transfer one or many 512-byte sectors. + * @qc: Command on going + * + * Transfer one or many ATA_SECT_SIZE of data from/to the + * ATA device for the DRQ request. + * + * LOCKING: + * Inherited from caller. + */ + +static void ata_pio_sectors(struct ata_queued_cmd *qc) +{ + if (is_multi_taskfile(&qc->tf)) { + /* READ/WRITE MULTIPLE */ + unsigned int nsect; + + WARN_ON(qc->dev->multi_count == 0); + + nsect = min(qc->nsect - qc->cursect, qc->dev->multi_count); + while (nsect--) + ata_pio_sector(qc); + } else + ata_pio_sector(qc); +} + +/** + * atapi_send_cdb - Write CDB bytes to hardware + * @ap: Port to which ATAPI device is attached. + * @qc: Taskfile currently active + * + * When device has indicated its readiness to accept + * a CDB, this function is called. Send the CDB. + * + * LOCKING: + * caller. + */ + +static void atapi_send_cdb(struct ata_port *ap, struct ata_queued_cmd *qc) +{ + /* send SCSI cdb */ + DPRINTK("send cdb\n"); + WARN_ON(qc->dev->cdb_len < 12); + + ap->ops->data_xfer(qc->dev, qc->cdb, qc->dev->cdb_len, 1); + ata_altstatus(ap); /* flush */ + + switch (qc->tf.protocol) { + case ATA_PROT_ATAPI: + ap->hsm_task_state = HSM_ST; + break; + case ATA_PROT_ATAPI_NODATA: + ap->hsm_task_state = HSM_ST_LAST; + break; + case ATA_PROT_ATAPI_DMA: + ap->hsm_task_state = HSM_ST_LAST; + /* initiate bmdma */ + ap->ops->bmdma_start(qc); + break; + } +} + +/** + * __atapi_pio_bytes - Transfer data from/to the ATAPI device. + * @qc: Command on going + * @bytes: number of bytes + * + * Transfer Transfer data from/to the ATAPI device. + * + * LOCKING: + * Inherited from caller. + * + */ + +static void __atapi_pio_bytes(struct ata_queued_cmd *qc, unsigned int bytes) +{ + int do_write = (qc->tf.flags & ATA_TFLAG_WRITE); + struct scatterlist *sg = qc->__sg; + struct ata_port *ap = qc->ap; + struct page *page; + unsigned char *buf; + unsigned int offset, count; + + if (qc->curbytes + bytes >= qc->nbytes) + ap->hsm_task_state = HSM_ST_LAST; + +next_sg: + if (unlikely(qc->cursg >= qc->n_elem)) { + /* + * The end of qc->sg is reached and the device expects + * more data to transfer. In order not to overrun qc->sg + * and fulfill length specified in the byte count register, + * - for read case, discard trailing data from the device + * - for write case, padding zero data to the device + */ + u16 pad_buf[1] = { 0 }; + unsigned int words = bytes >> 1; + unsigned int i; + + if (words) /* warning if bytes > 1 */ + ata_dev_printk(qc->dev, KERN_WARNING, + "%u bytes trailing data\n", bytes); + + for (i = 0; i < words; i++) + ap->ops->data_xfer(qc->dev, (unsigned char*)pad_buf, 2, do_write); + + ap->hsm_task_state = HSM_ST_LAST; + return; + } + + sg = &qc->__sg[qc->cursg]; + + page = sg->page; + offset = sg->offset + qc->cursg_ofs; + + /* get the current page and offset */ + page = nth_page(page, (offset >> PAGE_SHIFT)); + offset %= PAGE_SIZE; + + /* don't overrun current sg */ + count = min(sg->length - qc->cursg_ofs, bytes); + + /* don't cross page boundaries */ + count = min(count, (unsigned int)PAGE_SIZE - offset); + + DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read"); + + if (PageHighMem(page)) { + unsigned long flags; + + /* FIXME: use bounce buffer */ + local_irq_save(flags); + buf = kmap_atomic(page, KM_IRQ0); + + /* do the actual data transfer */ + ap->ops->data_xfer(qc->dev, buf + offset, count, do_write); + + kunmap_atomic(buf, KM_IRQ0); + local_irq_restore(flags); + } else { + buf = page_address(page); + ap->ops->data_xfer(qc->dev, buf + offset, count, do_write); + } + + bytes -= count; + qc->curbytes += count; + qc->cursg_ofs += count; + + if (qc->cursg_ofs == sg->length) { + qc->cursg++; + qc->cursg_ofs = 0; + } + + if (bytes) + goto next_sg; +} + +/** + * atapi_pio_bytes - Transfer data from/to the ATAPI device. + * @qc: Command on going + * + * Transfer Transfer data from/to the ATAPI device. + * + * LOCKING: + * Inherited from caller. + */ + +static void atapi_pio_bytes(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *dev = qc->dev; + unsigned int ireason, bc_lo, bc_hi, bytes; + int i_write, do_write = (qc->tf.flags & ATA_TFLAG_WRITE) ? 1 : 0; + + /* Abuse qc->result_tf for temp storage of intermediate TF + * here to save some kernel stack usage. + * For normal completion, qc->result_tf is not relevant. For + * error, qc->result_tf is later overwritten by ata_qc_complete(). + * So, the correctness of qc->result_tf is not affected. + */ + ap->ops->tf_read(ap, &qc->result_tf); + ireason = qc->result_tf.nsect; + bc_lo = qc->result_tf.lbam; + bc_hi = qc->result_tf.lbah; + bytes = (bc_hi << 8) | bc_lo; + + /* shall be cleared to zero, indicating xfer of data */ + if (ireason & (1 << 0)) + goto err_out; + + /* make sure transfer direction matches expected */ + i_write = ((ireason & (1 << 1)) == 0) ? 1 : 0; + if (do_write != i_write) + goto err_out; + + VPRINTK("ata%u: xfering %d bytes\n", ap->id, bytes); + + __atapi_pio_bytes(qc, bytes); + + return; + +err_out: + ata_dev_printk(dev, KERN_INFO, "ATAPI check failed\n"); + qc->err_mask |= AC_ERR_HSM; + ap->hsm_task_state = HSM_ST_ERR; +} + +/** + * ata_hsm_ok_in_wq - Check if the qc can be handled in the workqueue. + * @ap: the target ata_port + * @qc: qc on going + * + * RETURNS: + * 1 if ok in workqueue, 0 otherwise. + */ + +static inline int ata_hsm_ok_in_wq(struct ata_port *ap, struct ata_queued_cmd *qc) +{ + if (qc->tf.flags & ATA_TFLAG_POLLING) + return 1; + + if (ap->hsm_task_state == HSM_ST_FIRST) { + if (qc->tf.protocol == ATA_PROT_PIO && + (qc->tf.flags & ATA_TFLAG_WRITE)) + return 1; + + if (is_atapi_taskfile(&qc->tf) && + !(qc->dev->flags & ATA_DFLAG_CDB_INTR)) + return 1; + } + + return 0; +} + +/** + * ata_hsm_qc_complete - finish a qc running on standard HSM + * @qc: Command to complete + * @in_wq: 1 if called from workqueue, 0 otherwise + * + * Finish @qc which is running on standard HSM. + * + * LOCKING: + * If @in_wq is zero, spin_lock_irqsave(host lock). + * Otherwise, none on entry and grabs host lock. + */ +static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq) +{ + struct ata_port *ap = qc->ap; + unsigned long flags; + + if (ap->ops->error_handler) { + if (in_wq) { + spin_lock_irqsave(ap->lock, flags); + + /* EH might have kicked in while host lock is + * released. + */ + qc = ata_qc_from_tag(ap, qc->tag); + if (qc) { + if (likely(!(qc->err_mask & AC_ERR_HSM))) { + ata_irq_on(ap); + ata_qc_complete(qc); + } else + ata_port_freeze(ap); + } + + spin_unlock_irqrestore(ap->lock, flags); + } else { + if (likely(!(qc->err_mask & AC_ERR_HSM))) + ata_qc_complete(qc); + else + ata_port_freeze(ap); + } + } else { + if (in_wq) { + spin_lock_irqsave(ap->lock, flags); + ata_irq_on(ap); + ata_qc_complete(qc); + spin_unlock_irqrestore(ap->lock, flags); + } else + ata_qc_complete(qc); + } + + ata_altstatus(ap); /* flush */ +} + +/** + * ata_hsm_move - move the HSM to the next state. + * @ap: the target ata_port + * @qc: qc on going + * @status: current device status + * @in_wq: 1 if called from workqueue, 0 otherwise + * + * RETURNS: + * 1 when poll next status needed, 0 otherwise. + */ +int ata_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc, + u8 status, int in_wq) +{ + unsigned long flags = 0; + int poll_next; + + WARN_ON((qc->flags & ATA_QCFLAG_ACTIVE) == 0); + + /* Make sure ata_qc_issue_prot() does not throw things + * like DMA polling into the workqueue. Notice that + * in_wq is not equivalent to (qc->tf.flags & ATA_TFLAG_POLLING). + */ + WARN_ON(in_wq != ata_hsm_ok_in_wq(ap, qc)); + +fsm_start: + DPRINTK("ata%u: protocol %d task_state %d (dev_stat 0x%X)\n", + ap->id, qc->tf.protocol, ap->hsm_task_state, status); + + switch (ap->hsm_task_state) { + case HSM_ST_FIRST: + /* Send first data block or PACKET CDB */ + + /* If polling, we will stay in the work queue after + * sending the data. Otherwise, interrupt handler + * takes over after sending the data. + */ + poll_next = (qc->tf.flags & ATA_TFLAG_POLLING); + + /* check device status */ + if (unlikely((status & ATA_DRQ) == 0)) { + /* handle BSY=0, DRQ=0 as error */ + if (likely(status & (ATA_ERR | ATA_DF))) + /* device stops HSM for abort/error */ + qc->err_mask |= AC_ERR_DEV; + else + /* HSM violation. Let EH handle this */ + qc->err_mask |= AC_ERR_HSM; + + ap->hsm_task_state = HSM_ST_ERR; + goto fsm_start; + } + + /* Device should not ask for data transfer (DRQ=1) + * when it finds something wrong. + * We ignore DRQ here and stop the HSM by + * changing hsm_task_state to HSM_ST_ERR and + * let the EH abort the command or reset the device. + */ + if (unlikely(status & (ATA_ERR | ATA_DF))) { + printk(KERN_WARNING "ata%d: DRQ=1 with device error, dev_stat 0x%X\n", + ap->id, status); + qc->err_mask |= AC_ERR_HSM; + ap->hsm_task_state = HSM_ST_ERR; + goto fsm_start; + } + + /* Send the CDB (atapi) or the first data block (ata pio out). + * During the state transition, interrupt handler shouldn't + * be invoked before the data transfer is complete and + * hsm_task_state is changed. Hence, the following locking. + */ + if (in_wq) + spin_lock_irqsave(ap->lock, flags); + + if (qc->tf.protocol == ATA_PROT_PIO) { + /* PIO data out protocol. + * send first data block. + */ + + /* ata_pio_sectors() might change the state + * to HSM_ST_LAST. so, the state is changed here + * before ata_pio_sectors(). + */ + ap->hsm_task_state = HSM_ST; + ata_pio_sectors(qc); + ata_altstatus(ap); /* flush */ + } else + /* send CDB */ + atapi_send_cdb(ap, qc); + + if (in_wq) + spin_unlock_irqrestore(ap->lock, flags); + + /* if polling, ata_pio_task() handles the rest. + * otherwise, interrupt handler takes over from here. + */ + break; + + case HSM_ST: + /* complete command or read/write the data register */ + if (qc->tf.protocol == ATA_PROT_ATAPI) { + /* ATAPI PIO protocol */ + if ((status & ATA_DRQ) == 0) { + /* No more data to transfer or device error. + * Device error will be tagged in HSM_ST_LAST. + */ + ap->hsm_task_state = HSM_ST_LAST; + goto fsm_start; + } + + /* Device should not ask for data transfer (DRQ=1) + * when it finds something wrong. + * We ignore DRQ here and stop the HSM by + * changing hsm_task_state to HSM_ST_ERR and + * let the EH abort the command or reset the device. + */ + if (unlikely(status & (ATA_ERR | ATA_DF))) { + printk(KERN_WARNING "ata%d: DRQ=1 with device error, dev_stat 0x%X\n", + ap->id, status); + qc->err_mask |= AC_ERR_HSM; + ap->hsm_task_state = HSM_ST_ERR; + goto fsm_start; + } + + atapi_pio_bytes(qc); + + if (unlikely(ap->hsm_task_state == HSM_ST_ERR)) + /* bad ireason reported by device */ + goto fsm_start; + + } else { + /* ATA PIO protocol */ + if (unlikely((status & ATA_DRQ) == 0)) { + /* handle BSY=0, DRQ=0 as error */ + if (likely(status & (ATA_ERR | ATA_DF))) + /* device stops HSM for abort/error */ + qc->err_mask |= AC_ERR_DEV; + else + /* HSM violation. Let EH handle this */ + qc->err_mask |= AC_ERR_HSM; + + ap->hsm_task_state = HSM_ST_ERR; + goto fsm_start; + } + + /* For PIO reads, some devices may ask for + * data transfer (DRQ=1) alone with ERR=1. + * We respect DRQ here and transfer one + * block of junk data before changing the + * hsm_task_state to HSM_ST_ERR. + * + * For PIO writes, ERR=1 DRQ=1 doesn't make + * sense since the data block has been + * transferred to the device. + */ + if (unlikely(status & (ATA_ERR | ATA_DF))) { + /* data might be corrputed */ + qc->err_mask |= AC_ERR_DEV; + + if (!(qc->tf.flags & ATA_TFLAG_WRITE)) { + ata_pio_sectors(qc); + ata_altstatus(ap); + status = ata_wait_idle(ap); + } + + if (status & (ATA_BUSY | ATA_DRQ)) + qc->err_mask |= AC_ERR_HSM; + + /* ata_pio_sectors() might change the + * state to HSM_ST_LAST. so, the state + * is changed after ata_pio_sectors(). + */ + ap->hsm_task_state = HSM_ST_ERR; + goto fsm_start; + } + + ata_pio_sectors(qc); + + if (ap->hsm_task_state == HSM_ST_LAST && + (!(qc->tf.flags & ATA_TFLAG_WRITE))) { + /* all data read */ + ata_altstatus(ap); + status = ata_wait_idle(ap); + goto fsm_start; + } + } + + ata_altstatus(ap); /* flush */ + poll_next = 1; + break; + + case HSM_ST_LAST: + if (unlikely(!ata_ok(status))) { + qc->err_mask |= __ac_err_mask(status); + ap->hsm_task_state = HSM_ST_ERR; + goto fsm_start; + } + + /* no more data to transfer */ + DPRINTK("ata%u: dev %u command complete, drv_stat 0x%x\n", + ap->id, qc->dev->devno, status); + + WARN_ON(qc->err_mask); + + ap->hsm_task_state = HSM_ST_IDLE; + + /* complete taskfile transaction */ + ata_hsm_qc_complete(qc, in_wq); + + poll_next = 0; + break; + + case HSM_ST_ERR: + /* make sure qc->err_mask is available to + * know what's wrong and recover + */ + WARN_ON(qc->err_mask == 0); + + ap->hsm_task_state = HSM_ST_IDLE; + + /* complete taskfile transaction */ + ata_hsm_qc_complete(qc, in_wq); + + poll_next = 0; + break; + default: + poll_next = 0; + BUG(); + } + + return poll_next; +} + +static void ata_pio_task(void *_data) +{ + struct ata_queued_cmd *qc = _data; + struct ata_port *ap = qc->ap; + u8 status; + int poll_next; + +fsm_start: + WARN_ON(ap->hsm_task_state == HSM_ST_IDLE); + + /* + * This is purely heuristic. This is a fast path. + * Sometimes when we enter, BSY will be cleared in + * a chk-status or two. If not, the drive is probably seeking + * or something. Snooze for a couple msecs, then + * chk-status again. If still busy, queue delayed work. + */ + status = ata_busy_wait(ap, ATA_BUSY, 5); + if (status & ATA_BUSY) { + msleep(2); + status = ata_busy_wait(ap, ATA_BUSY, 10); + if (status & ATA_BUSY) { + ata_port_queue_task(ap, ata_pio_task, qc, ATA_SHORT_PAUSE); + return; + } + } + + /* move the HSM */ + poll_next = ata_hsm_move(ap, qc, status, 1); + + /* another command or interrupt handler + * may be running at this point. + */ + if (poll_next) + goto fsm_start; +} + +/** + * ata_qc_new - Request an available ATA command, for queueing + * @ap: Port associated with device @dev + * @dev: Device from whom we request an available command structure + * + * LOCKING: + * None. + */ + +static struct ata_queued_cmd *ata_qc_new(struct ata_port *ap) +{ + struct ata_queued_cmd *qc = NULL; + unsigned int i; + + /* no command while frozen */ + if (unlikely(ap->pflags & ATA_PFLAG_FROZEN)) + return NULL; + + /* the last tag is reserved for internal command. */ + for (i = 0; i < ATA_MAX_QUEUE - 1; i++) + if (!test_and_set_bit(i, &ap->qc_allocated)) { + qc = __ata_qc_from_tag(ap, i); + break; + } + + if (qc) + qc->tag = i; + + return qc; +} + +/** + * ata_qc_new_init - Request an available ATA command, and initialize it + * @dev: Device from whom we request an available command structure + * + * LOCKING: + * None. + */ + +struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev) +{ + struct ata_port *ap = dev->ap; + struct ata_queued_cmd *qc; + + qc = ata_qc_new(ap); + if (qc) { + qc->scsicmd = NULL; + qc->ap = ap; + qc->dev = dev; + + ata_qc_reinit(qc); + } + + return qc; +} + +/** + * ata_qc_free - free unused ata_queued_cmd + * @qc: Command to complete + * + * Designed to free unused ata_queued_cmd object + * in case something prevents using it. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_qc_free(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + unsigned int tag; + + WARN_ON(qc == NULL); /* ata_qc_from_tag _might_ return NULL */ + + qc->flags = 0; + tag = qc->tag; + if (likely(ata_tag_valid(tag))) { + qc->tag = ATA_TAG_POISON; + clear_bit(tag, &ap->qc_allocated); + } +} + +void __ata_qc_complete(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + WARN_ON(qc == NULL); /* ata_qc_from_tag _might_ return NULL */ + WARN_ON(!(qc->flags & ATA_QCFLAG_ACTIVE)); + + if (likely(qc->flags & ATA_QCFLAG_DMAMAP)) + ata_sg_clean(qc); + + /* command should be marked inactive atomically with qc completion */ + if (qc->tf.protocol == ATA_PROT_NCQ) + ap->sactive &= ~(1 << qc->tag); + else + ap->active_tag = ATA_TAG_POISON; + + /* atapi: mark qc as inactive to prevent the interrupt handler + * from completing the command twice later, before the error handler + * is called. (when rc != 0 and atapi request sense is needed) + */ + qc->flags &= ~ATA_QCFLAG_ACTIVE; + ap->qc_active &= ~(1 << qc->tag); + + /* call completion callback */ + qc->complete_fn(qc); +} + +/** + * ata_qc_complete - Complete an active ATA command + * @qc: Command to complete + * @err_mask: ATA Status register contents + * + * Indicate to the mid and upper layers that an ATA + * command has completed, with either an ok or not-ok status. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_qc_complete(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + /* XXX: New EH and old EH use different mechanisms to + * synchronize EH with regular execution path. + * + * In new EH, a failed qc is marked with ATA_QCFLAG_FAILED. + * Normal execution path is responsible for not accessing a + * failed qc. libata core enforces the rule by returning NULL + * from ata_qc_from_tag() for failed qcs. + * + * Old EH depends on ata_qc_complete() nullifying completion + * requests if ATA_QCFLAG_EH_SCHEDULED is set. Old EH does + * not synchronize with interrupt handler. Only PIO task is + * taken care of. + */ + if (ap->ops->error_handler) { + WARN_ON(ap->pflags & ATA_PFLAG_FROZEN); + + if (unlikely(qc->err_mask)) + qc->flags |= ATA_QCFLAG_FAILED; + + if (unlikely(qc->flags & ATA_QCFLAG_FAILED)) { + if (!ata_tag_internal(qc->tag)) { + /* always fill result TF for failed qc */ + ap->ops->tf_read(ap, &qc->result_tf); + ata_qc_schedule_eh(qc); + return; + } + } + + /* read result TF if requested */ + if (qc->flags & ATA_QCFLAG_RESULT_TF) + ap->ops->tf_read(ap, &qc->result_tf); + + __ata_qc_complete(qc); + } else { + if (qc->flags & ATA_QCFLAG_EH_SCHEDULED) + return; + + /* read result TF if failed or requested */ + if (qc->err_mask || qc->flags & ATA_QCFLAG_RESULT_TF) + ap->ops->tf_read(ap, &qc->result_tf); + + __ata_qc_complete(qc); + } +} + +/** + * ata_qc_complete_multiple - Complete multiple qcs successfully + * @ap: port in question + * @qc_active: new qc_active mask + * @finish_qc: LLDD callback invoked before completing a qc + * + * Complete in-flight commands. This functions is meant to be + * called from low-level driver's interrupt routine to complete + * requests normally. ap->qc_active and @qc_active is compared + * and commands are completed accordingly. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Number of completed commands on success, -errno otherwise. + */ +int ata_qc_complete_multiple(struct ata_port *ap, u32 qc_active, + void (*finish_qc)(struct ata_queued_cmd *)) +{ + int nr_done = 0; + u32 done_mask; + int i; + + done_mask = ap->qc_active ^ qc_active; + + if (unlikely(done_mask & qc_active)) { + ata_port_printk(ap, KERN_ERR, "illegal qc_active transition " + "(%08x->%08x)\n", ap->qc_active, qc_active); + return -EINVAL; + } + + for (i = 0; i < ATA_MAX_QUEUE; i++) { + struct ata_queued_cmd *qc; + + if (!(done_mask & (1 << i))) + continue; + + if ((qc = ata_qc_from_tag(ap, i))) { + if (finish_qc) + finish_qc(qc); + ata_qc_complete(qc); + nr_done++; + } + } + + return nr_done; +} + +static inline int ata_should_dma_map(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + switch (qc->tf.protocol) { + case ATA_PROT_NCQ: + case ATA_PROT_DMA: + case ATA_PROT_ATAPI_DMA: + return 1; + + case ATA_PROT_ATAPI: + case ATA_PROT_PIO: + if (ap->flags & ATA_FLAG_PIO_DMA) + return 1; + + /* fall through */ + + default: + return 0; + } + + /* never reached */ +} + +/** + * ata_qc_issue - issue taskfile to device + * @qc: command to issue to device + * + * Prepare an ATA command to submission to device. + * This includes mapping the data into a DMA-able + * area, filling in the S/G table, and finally + * writing the taskfile to hardware, starting the command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + /* Make sure only one non-NCQ command is outstanding. The + * check is skipped for old EH because it reuses active qc to + * request ATAPI sense. + */ + WARN_ON(ap->ops->error_handler && ata_tag_valid(ap->active_tag)); + + if (qc->tf.protocol == ATA_PROT_NCQ) { + WARN_ON(ap->sactive & (1 << qc->tag)); + ap->sactive |= 1 << qc->tag; + } else { + WARN_ON(ap->sactive); + ap->active_tag = qc->tag; + } + + qc->flags |= ATA_QCFLAG_ACTIVE; + ap->qc_active |= 1 << qc->tag; + + if (ata_should_dma_map(qc)) { + if (qc->flags & ATA_QCFLAG_SG) { + if (ata_sg_setup(qc)) + goto sg_err; + } else if (qc->flags & ATA_QCFLAG_SINGLE) { + if (ata_sg_setup_one(qc)) + goto sg_err; + } + } else { + qc->flags &= ~ATA_QCFLAG_DMAMAP; + } + + ap->ops->qc_prep(qc); + + qc->err_mask |= ap->ops->qc_issue(qc); + if (unlikely(qc->err_mask)) + goto err; + return; + +sg_err: + qc->flags &= ~ATA_QCFLAG_DMAMAP; + qc->err_mask |= AC_ERR_SYSTEM; +err: + ata_qc_complete(qc); +} + +/** + * ata_qc_issue_prot - issue taskfile to device in proto-dependent manner + * @qc: command to issue to device + * + * Using various libata functions and hooks, this function + * starts an ATA command. ATA commands are grouped into + * classes called "protocols", and issuing each type of protocol + * is slightly different. + * + * May be used as the qc_issue() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, AC_ERR_* mask on failure + */ + +unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + /* Use polling pio if the LLD doesn't handle + * interrupt driven pio and atapi CDB interrupt. + */ + if (ap->flags & ATA_FLAG_PIO_POLLING) { + switch (qc->tf.protocol) { + case ATA_PROT_PIO: + case ATA_PROT_ATAPI: + case ATA_PROT_ATAPI_NODATA: + qc->tf.flags |= ATA_TFLAG_POLLING; + break; + case ATA_PROT_ATAPI_DMA: + if (qc->dev->flags & ATA_DFLAG_CDB_INTR) + /* see ata_dma_blacklisted() */ + BUG(); + break; + default: + break; + } + } + + /* select the device */ + ata_dev_select(ap, qc->dev->devno, 1, 0); + + /* start the command */ + switch (qc->tf.protocol) { + case ATA_PROT_NODATA: + if (qc->tf.flags & ATA_TFLAG_POLLING) + ata_qc_set_polling(qc); + + ata_tf_to_host(ap, &qc->tf); + ap->hsm_task_state = HSM_ST_LAST; + + if (qc->tf.flags & ATA_TFLAG_POLLING) + ata_port_queue_task(ap, ata_pio_task, qc, 0); + + break; + + case ATA_PROT_DMA: + WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING); + + ap->ops->tf_load(ap, &qc->tf); /* load tf registers */ + ap->ops->bmdma_setup(qc); /* set up bmdma */ + ap->ops->bmdma_start(qc); /* initiate bmdma */ + ap->hsm_task_state = HSM_ST_LAST; + break; + + case ATA_PROT_PIO: + if (qc->tf.flags & ATA_TFLAG_POLLING) + ata_qc_set_polling(qc); + + ata_tf_to_host(ap, &qc->tf); + + if (qc->tf.flags & ATA_TFLAG_WRITE) { + /* PIO data out protocol */ + ap->hsm_task_state = HSM_ST_FIRST; + ata_port_queue_task(ap, ata_pio_task, qc, 0); + + /* always send first data block using + * the ata_pio_task() codepath. + */ + } else { + /* PIO data in protocol */ + ap->hsm_task_state = HSM_ST; + + if (qc->tf.flags & ATA_TFLAG_POLLING) + ata_port_queue_task(ap, ata_pio_task, qc, 0); + + /* if polling, ata_pio_task() handles the rest. + * otherwise, interrupt handler takes over from here. + */ + } + + break; + + case ATA_PROT_ATAPI: + case ATA_PROT_ATAPI_NODATA: + if (qc->tf.flags & ATA_TFLAG_POLLING) + ata_qc_set_polling(qc); + + ata_tf_to_host(ap, &qc->tf); + + ap->hsm_task_state = HSM_ST_FIRST; + + /* send cdb by polling if no cdb interrupt */ + if ((!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) || + (qc->tf.flags & ATA_TFLAG_POLLING)) + ata_port_queue_task(ap, ata_pio_task, qc, 0); + break; + + case ATA_PROT_ATAPI_DMA: + WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING); + + ap->ops->tf_load(ap, &qc->tf); /* load tf registers */ + ap->ops->bmdma_setup(qc); /* set up bmdma */ + ap->hsm_task_state = HSM_ST_FIRST; + + /* send cdb by polling if no cdb interrupt */ + if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) + ata_port_queue_task(ap, ata_pio_task, qc, 0); + break; + + default: + WARN_ON(1); + return AC_ERR_SYSTEM; + } + + return 0; +} + +/** + * ata_host_intr - Handle host interrupt for given (port, task) + * @ap: Port on which interrupt arrived (possibly...) + * @qc: Taskfile currently active in engine + * + * Handle host interrupt for given queued command. Currently, + * only DMA interrupts are handled. All other commands are + * handled via polling with interrupts disabled (nIEN bit). + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * One if interrupt was handled, zero if not (shared irq). + */ + +inline unsigned int ata_host_intr (struct ata_port *ap, + struct ata_queued_cmd *qc) +{ + u8 status, host_stat = 0; + + VPRINTK("ata%u: protocol %d task_state %d\n", + ap->id, qc->tf.protocol, ap->hsm_task_state); + + /* Check whether we are expecting interrupt in this state */ + switch (ap->hsm_task_state) { + case HSM_ST_FIRST: + /* Some pre-ATAPI-4 devices assert INTRQ + * at this state when ready to receive CDB. + */ + + /* Check the ATA_DFLAG_CDB_INTR flag is enough here. + * The flag was turned on only for atapi devices. + * No need to check is_atapi_taskfile(&qc->tf) again. + */ + if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) + goto idle_irq; + break; + case HSM_ST_LAST: + if (qc->tf.protocol == ATA_PROT_DMA || + qc->tf.protocol == ATA_PROT_ATAPI_DMA) { + /* check status of DMA engine */ + host_stat = ap->ops->bmdma_status(ap); + VPRINTK("ata%u: host_stat 0x%X\n", ap->id, host_stat); + + /* if it's not our irq... */ + if (!(host_stat & ATA_DMA_INTR)) + goto idle_irq; + + /* before we do anything else, clear DMA-Start bit */ + ap->ops->bmdma_stop(qc); + + if (unlikely(host_stat & ATA_DMA_ERR)) { + /* error when transfering data to/from memory */ + qc->err_mask |= AC_ERR_HOST_BUS; + ap->hsm_task_state = HSM_ST_ERR; + } + } + break; + case HSM_ST: + break; + default: + goto idle_irq; + } + + /* check altstatus */ + status = ata_altstatus(ap); + if (status & ATA_BUSY) + goto idle_irq; + + /* check main status, clearing INTRQ */ + status = ata_chk_status(ap); + if (unlikely(status & ATA_BUSY)) + goto idle_irq; + + /* ack bmdma irq events */ + ap->ops->irq_clear(ap); + + ata_hsm_move(ap, qc, status, 0); + return 1; /* irq handled */ + +idle_irq: + ap->stats.idle_irq++; + +#ifdef ATA_IRQ_TRAP + if ((ap->stats.idle_irq % 1000) == 0) { + ata_irq_ack(ap, 0); /* debug trap */ + ata_port_printk(ap, KERN_WARNING, "irq trap\n"); + return 1; + } +#endif + return 0; /* irq not handled */ +} + +/** + * ata_interrupt - Default ATA host interrupt handler + * @irq: irq line (unused) + * @dev_instance: pointer to our ata_host information structure + * @regs: unused + * + * Default interrupt handler for PCI IDE devices. Calls + * ata_host_intr() for each port that is not disabled. + * + * LOCKING: + * Obtains host lock during operation. + * + * RETURNS: + * IRQ_NONE or IRQ_HANDLED. + */ + +irqreturn_t ata_interrupt (int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + unsigned int i; + unsigned int handled = 0; + unsigned long flags; + + /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */ + spin_lock_irqsave(&host->lock, flags); + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap; + + ap = host->ports[i]; + if (ap && + !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) && + (qc->flags & ATA_QCFLAG_ACTIVE)) + handled |= ata_host_intr(ap, qc); + } + } + + spin_unlock_irqrestore(&host->lock, flags); + + return IRQ_RETVAL(handled); +} + +/** + * sata_scr_valid - test whether SCRs are accessible + * @ap: ATA port to test SCR accessibility for + * + * Test whether SCRs are accessible for @ap. + * + * LOCKING: + * None. + * + * RETURNS: + * 1 if SCRs are accessible, 0 otherwise. + */ +int sata_scr_valid(struct ata_port *ap) +{ + return ap->cbl == ATA_CBL_SATA && ap->ops->scr_read; +} + +/** + * sata_scr_read - read SCR register of the specified port + * @ap: ATA port to read SCR for + * @reg: SCR to read + * @val: Place to store read value + * + * Read SCR register @reg of @ap into *@val. This function is + * guaranteed to succeed if the cable type of the port is SATA + * and the port implements ->scr_read. + * + * LOCKING: + * None. + * + * RETURNS: + * 0 on success, negative errno on failure. + */ +int sata_scr_read(struct ata_port *ap, int reg, u32 *val) +{ + if (sata_scr_valid(ap)) { + *val = ap->ops->scr_read(ap, reg); + return 0; + } + return -EOPNOTSUPP; +} + +/** + * sata_scr_write - write SCR register of the specified port + * @ap: ATA port to write SCR for + * @reg: SCR to write + * @val: value to write + * + * Write @val to SCR register @reg of @ap. This function is + * guaranteed to succeed if the cable type of the port is SATA + * and the port implements ->scr_read. + * + * LOCKING: + * None. + * + * RETURNS: + * 0 on success, negative errno on failure. + */ +int sata_scr_write(struct ata_port *ap, int reg, u32 val) +{ + if (sata_scr_valid(ap)) { + ap->ops->scr_write(ap, reg, val); + return 0; + } + return -EOPNOTSUPP; +} + +/** + * sata_scr_write_flush - write SCR register of the specified port and flush + * @ap: ATA port to write SCR for + * @reg: SCR to write + * @val: value to write + * + * This function is identical to sata_scr_write() except that this + * function performs flush after writing to the register. + * + * LOCKING: + * None. + * + * RETURNS: + * 0 on success, negative errno on failure. + */ +int sata_scr_write_flush(struct ata_port *ap, int reg, u32 val) +{ + if (sata_scr_valid(ap)) { + ap->ops->scr_write(ap, reg, val); + ap->ops->scr_read(ap, reg); + return 0; + } + return -EOPNOTSUPP; +} + +/** + * ata_port_online - test whether the given port is online + * @ap: ATA port to test + * + * Test whether @ap is online. Note that this function returns 0 + * if online status of @ap cannot be obtained, so + * ata_port_online(ap) != !ata_port_offline(ap). + * + * LOCKING: + * None. + * + * RETURNS: + * 1 if the port online status is available and online. + */ +int ata_port_online(struct ata_port *ap) +{ + u32 sstatus; + + if (!sata_scr_read(ap, SCR_STATUS, &sstatus) && (sstatus & 0xf) == 0x3) + return 1; + return 0; +} + +/** + * ata_port_offline - test whether the given port is offline + * @ap: ATA port to test + * + * Test whether @ap is offline. Note that this function returns + * 0 if offline status of @ap cannot be obtained, so + * ata_port_online(ap) != !ata_port_offline(ap). + * + * LOCKING: + * None. + * + * RETURNS: + * 1 if the port offline status is available and offline. + */ +int ata_port_offline(struct ata_port *ap) +{ + u32 sstatus; + + if (!sata_scr_read(ap, SCR_STATUS, &sstatus) && (sstatus & 0xf) != 0x3) + return 1; + return 0; +} + +int ata_flush_cache(struct ata_device *dev) +{ + unsigned int err_mask; + u8 cmd; + + if (!ata_try_flush_cache(dev)) + return 0; + + if (ata_id_has_flush_ext(dev->id)) + cmd = ATA_CMD_FLUSH_EXT; + else + cmd = ATA_CMD_FLUSH; + + err_mask = ata_do_simple_cmd(dev, cmd); + if (err_mask) { + ata_dev_printk(dev, KERN_ERR, "failed to flush cache\n"); + return -EIO; + } + + return 0; +} + +static int ata_host_request_pm(struct ata_host *host, pm_message_t mesg, + unsigned int action, unsigned int ehi_flags, + int wait) +{ + unsigned long flags; + int i, rc; + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + + /* Previous resume operation might still be in + * progress. Wait for PM_PENDING to clear. + */ + if (ap->pflags & ATA_PFLAG_PM_PENDING) { + ata_port_wait_eh(ap); + WARN_ON(ap->pflags & ATA_PFLAG_PM_PENDING); + } + + /* request PM ops to EH */ + spin_lock_irqsave(ap->lock, flags); + + ap->pm_mesg = mesg; + if (wait) { + rc = 0; + ap->pm_result = &rc; + } + + ap->pflags |= ATA_PFLAG_PM_PENDING; + ap->eh_info.action |= action; + ap->eh_info.flags |= ehi_flags; + + ata_port_schedule_eh(ap); + + spin_unlock_irqrestore(ap->lock, flags); + + /* wait and check result */ + if (wait) { + ata_port_wait_eh(ap); + WARN_ON(ap->pflags & ATA_PFLAG_PM_PENDING); + if (rc) + return rc; + } + } + + return 0; +} + +/** + * ata_host_suspend - suspend host + * @host: host to suspend + * @mesg: PM message + * + * Suspend @host. Actual operation is performed by EH. This + * function requests EH to perform PM operations and waits for EH + * to finish. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno on failure. + */ +int ata_host_suspend(struct ata_host *host, pm_message_t mesg) +{ + int i, j, rc; + + rc = ata_host_request_pm(host, mesg, 0, ATA_EHI_QUIET, 1); + if (rc) + goto fail; + + /* EH is quiescent now. Fail if we have any ready device. + * This happens if hotplug occurs between completion of device + * suspension and here. + */ + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + + for (j = 0; j < ATA_MAX_DEVICES; j++) { + struct ata_device *dev = &ap->device[j]; + + if (ata_dev_ready(dev)) { + ata_port_printk(ap, KERN_WARNING, + "suspend failed, device %d " + "still active\n", dev->devno); + rc = -EBUSY; + goto fail; + } + } + } + + host->dev->power.power_state = mesg; + return 0; + + fail: + ata_host_resume(host); + return rc; +} + +/** + * ata_host_resume - resume host + * @host: host to resume + * + * Resume @host. Actual operation is performed by EH. This + * function requests EH to perform PM operations and returns. + * Note that all resume operations are performed parallely. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +void ata_host_resume(struct ata_host *host) +{ + ata_host_request_pm(host, PMSG_ON, ATA_EH_SOFTRESET, + ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET, 0); + host->dev->power.power_state = PMSG_ON; +} + +/** + * ata_port_start - Set port up for dma. + * @ap: Port to initialize + * + * Called just after data structures for each port are + * initialized. Allocates space for PRD table. + * + * May be used as the port_start() entry in ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ + +int ata_port_start (struct ata_port *ap) +{ + struct device *dev = ap->dev; + int rc; + + ap->prd = dma_alloc_coherent(dev, ATA_PRD_TBL_SZ, &ap->prd_dma, GFP_KERNEL); + if (!ap->prd) + return -ENOMEM; + + rc = ata_pad_alloc(ap, dev); + if (rc) { + dma_free_coherent(dev, ATA_PRD_TBL_SZ, ap->prd, ap->prd_dma); + return rc; + } + + DPRINTK("prd alloc, virt %p, dma %llx\n", ap->prd, (unsigned long long) ap->prd_dma); + + return 0; +} + + +/** + * ata_port_stop - Undo ata_port_start() + * @ap: Port to shut down + * + * Frees the PRD table. + * + * May be used as the port_stop() entry in ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ + +void ata_port_stop (struct ata_port *ap) +{ + struct device *dev = ap->dev; + + dma_free_coherent(dev, ATA_PRD_TBL_SZ, ap->prd, ap->prd_dma); + ata_pad_free(ap, dev); +} + +void ata_host_stop (struct ata_host *host) +{ + if (host->mmio_base) + iounmap(host->mmio_base); +} + +/** + * ata_dev_init - Initialize an ata_device structure + * @dev: Device structure to initialize + * + * Initialize @dev in preparation for probing. + * + * LOCKING: + * Inherited from caller. + */ +void ata_dev_init(struct ata_device *dev) +{ + struct ata_port *ap = dev->ap; + unsigned long flags; + + /* SATA spd limit is bound to the first device */ + ap->sata_spd_limit = ap->hw_sata_spd_limit; + + /* High bits of dev->flags are used to record warm plug + * requests which occur asynchronously. Synchronize using + * host lock. + */ + spin_lock_irqsave(ap->lock, flags); + dev->flags &= ~ATA_DFLAG_INIT_MASK; + spin_unlock_irqrestore(ap->lock, flags); + + memset((void *)dev + ATA_DEVICE_CLEAR_OFFSET, 0, + sizeof(*dev) - ATA_DEVICE_CLEAR_OFFSET); + dev->pio_mask = UINT_MAX; + dev->mwdma_mask = UINT_MAX; + dev->udma_mask = UINT_MAX; +} + +/** + * ata_port_init - Initialize an ata_port structure + * @ap: Structure to initialize + * @host: Collection of hosts to which @ap belongs + * @ent: Probe information provided by low-level driver + * @port_no: Port number associated with this ata_port + * + * Initialize a new ata_port structure. + * + * LOCKING: + * Inherited from caller. + */ +void ata_port_init(struct ata_port *ap, struct ata_host *host, + const struct ata_probe_ent *ent, unsigned int port_no) +{ + unsigned int i; + + ap->lock = &host->lock; + ap->flags = ATA_FLAG_DISABLED; + ap->id = ata_unique_id++; + ap->ctl = ATA_DEVCTL_OBS; + ap->host = host; + ap->dev = ent->dev; + ap->port_no = port_no; + if (port_no == 1 && ent->pinfo2) { + ap->pio_mask = ent->pinfo2->pio_mask; + ap->mwdma_mask = ent->pinfo2->mwdma_mask; + ap->udma_mask = ent->pinfo2->udma_mask; + ap->flags |= ent->pinfo2->flags; + ap->ops = ent->pinfo2->port_ops; + } else { + ap->pio_mask = ent->pio_mask; + ap->mwdma_mask = ent->mwdma_mask; + ap->udma_mask = ent->udma_mask; + ap->flags |= ent->port_flags; + ap->ops = ent->port_ops; + } + ap->hw_sata_spd_limit = UINT_MAX; + ap->active_tag = ATA_TAG_POISON; + ap->last_ctl = 0xFF; + +#if defined(ATA_VERBOSE_DEBUG) + /* turn on all debugging levels */ + ap->msg_enable = 0x00FF; +#elif defined(ATA_DEBUG) + ap->msg_enable = ATA_MSG_DRV | ATA_MSG_INFO | ATA_MSG_CTL | ATA_MSG_WARN | ATA_MSG_ERR; +#else + ap->msg_enable = ATA_MSG_DRV | ATA_MSG_ERR | ATA_MSG_WARN; +#endif + + INIT_WORK(&ap->port_task, NULL, NULL); + INIT_WORK(&ap->hotplug_task, ata_scsi_hotplug, ap); + INIT_WORK(&ap->scsi_rescan_task, ata_scsi_dev_rescan, ap); + INIT_LIST_HEAD(&ap->eh_done_q); + init_waitqueue_head(&ap->eh_wait_q); + + /* set cable type */ + ap->cbl = ATA_CBL_NONE; + if (ap->flags & ATA_FLAG_SATA) + ap->cbl = ATA_CBL_SATA; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + dev->ap = ap; + dev->devno = i; + ata_dev_init(dev); + } + +#ifdef ATA_IRQ_TRAP + ap->stats.unhandled_irq = 1; + ap->stats.idle_irq = 1; +#endif + + memcpy(&ap->ioaddr, &ent->port[port_no], sizeof(struct ata_ioports)); +} + +/** + * ata_port_init_shost - Initialize SCSI host associated with ATA port + * @ap: ATA port to initialize SCSI host for + * @shost: SCSI host associated with @ap + * + * Initialize SCSI host @shost associated with ATA port @ap. + * + * LOCKING: + * Inherited from caller. + */ +static void ata_port_init_shost(struct ata_port *ap, struct Scsi_Host *shost) +{ + ap->scsi_host = shost; + + shost->unique_id = ap->id; + shost->max_id = 16; + shost->max_lun = 1; + shost->max_channel = 1; + shost->max_cmd_len = 12; +} + +/** + * ata_port_add - Attach low-level ATA driver to system + * @ent: Information provided by low-level driver + * @host: Collections of ports to which we add + * @port_no: Port number associated with this host + * + * Attach low-level ATA driver to system. + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * New ata_port on success, for NULL on error. + */ +static struct ata_port * ata_port_add(const struct ata_probe_ent *ent, + struct ata_host *host, + unsigned int port_no) +{ + struct Scsi_Host *shost; + struct ata_port *ap; + + DPRINTK("ENTER\n"); + + if (!ent->port_ops->error_handler && + !(ent->port_flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST))) { + printk(KERN_ERR "ata%u: no reset mechanism available\n", + port_no); + return NULL; + } + + shost = scsi_host_alloc(ent->sht, sizeof(struct ata_port)); + if (!shost) + return NULL; + + shost->transportt = &ata_scsi_transport_template; + + ap = ata_shost_to_port(shost); + + ata_port_init(ap, host, ent, port_no); + ata_port_init_shost(ap, shost); + + return ap; +} + +/** + * ata_sas_host_init - Initialize a host struct + * @host: host to initialize + * @dev: device host is attached to + * @flags: host flags + * @ops: port_ops + * + * LOCKING: + * PCI/etc. bus probe sem. + * + */ + +void ata_host_init(struct ata_host *host, struct device *dev, + unsigned long flags, const struct ata_port_operations *ops) +{ + spin_lock_init(&host->lock); + host->dev = dev; + host->flags = flags; + host->ops = ops; +} + +/** + * ata_device_add - Register hardware device with ATA and SCSI layers + * @ent: Probe information describing hardware device to be registered + * + * This function processes the information provided in the probe + * information struct @ent, allocates the necessary ATA and SCSI + * host information structures, initializes them, and registers + * everything with requisite kernel subsystems. + * + * This function requests irqs, probes the ATA bus, and probes + * the SCSI bus. + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * Number of ports registered. Zero on error (no ports registered). + */ +int ata_device_add(const struct ata_probe_ent *ent) +{ + unsigned int i; + struct device *dev = ent->dev; + struct ata_host *host; + int rc; + + DPRINTK("ENTER\n"); + + if (ent->irq == 0) { + dev_printk(KERN_ERR, dev, "is not available: No interrupt assigned.\n"); + return 0; + } + /* alloc a container for our list of ATA ports (buses) */ + host = kzalloc(sizeof(struct ata_host) + + (ent->n_ports * sizeof(void *)), GFP_KERNEL); + if (!host) + return 0; + + ata_host_init(host, dev, ent->_host_flags, ent->port_ops); + host->n_ports = ent->n_ports; + host->irq = ent->irq; + host->irq2 = ent->irq2; + host->mmio_base = ent->mmio_base; + host->private_data = ent->private_data; + + /* register each port bound to this device */ + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap; + unsigned long xfer_mode_mask; + int irq_line = ent->irq; + + ap = ata_port_add(ent, host, i); + if (!ap) + goto err_out; + + host->ports[i] = ap; + + /* dummy? */ + if (ent->dummy_port_mask & (1 << i)) { + ata_port_printk(ap, KERN_INFO, "DUMMY\n"); + ap->ops = &ata_dummy_port_ops; + continue; + } + + /* start port */ + rc = ap->ops->port_start(ap); + if (rc) { + host->ports[i] = NULL; + scsi_host_put(ap->scsi_host); + goto err_out; + } + + /* Report the secondary IRQ for second channel legacy */ + if (i == 1 && ent->irq2) + irq_line = ent->irq2; + + xfer_mode_mask =(ap->udma_mask << ATA_SHIFT_UDMA) | + (ap->mwdma_mask << ATA_SHIFT_MWDMA) | + (ap->pio_mask << ATA_SHIFT_PIO); + + /* print per-port info to dmesg */ + ata_port_printk(ap, KERN_INFO, "%cATA max %s cmd 0x%lX " + "ctl 0x%lX bmdma 0x%lX irq %d\n", + ap->flags & ATA_FLAG_SATA ? 'S' : 'P', + ata_mode_string(xfer_mode_mask), + ap->ioaddr.cmd_addr, + ap->ioaddr.ctl_addr, + ap->ioaddr.bmdma_addr, + irq_line); + + ata_chk_status(ap); + host->ops->irq_clear(ap); + ata_eh_freeze_port(ap); /* freeze port before requesting IRQ */ + } + + /* obtain irq, that may be shared between channels */ + rc = request_irq(ent->irq, ent->port_ops->irq_handler, ent->irq_flags, + DRV_NAME, host); + if (rc) { + dev_printk(KERN_ERR, dev, "irq %lu request failed: %d\n", + ent->irq, rc); + goto err_out; + } + + /* do we have a second IRQ for the other channel, eg legacy mode */ + if (ent->irq2) { + /* We will get weird core code crashes later if this is true + so trap it now */ + BUG_ON(ent->irq == ent->irq2); + + rc = request_irq(ent->irq2, ent->port_ops->irq_handler, ent->irq_flags, + DRV_NAME, host); + if (rc) { + dev_printk(KERN_ERR, dev, "irq %lu request failed: %d\n", + ent->irq2, rc); + goto err_out_free_irq; + } + } + + /* perform each probe synchronously */ + DPRINTK("probe begin\n"); + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + u32 scontrol; + int rc; + + /* init sata_spd_limit to the current value */ + if (sata_scr_read(ap, SCR_CONTROL, &scontrol) == 0) { + int spd = (scontrol >> 4) & 0xf; + ap->hw_sata_spd_limit &= (1 << spd) - 1; + } + ap->sata_spd_limit = ap->hw_sata_spd_limit; + + rc = scsi_add_host(ap->scsi_host, dev); + if (rc) { + ata_port_printk(ap, KERN_ERR, "scsi_add_host failed\n"); + /* FIXME: do something useful here */ + /* FIXME: handle unconditional calls to + * scsi_scan_host and ata_host_remove, below, + * at the very least + */ + } + + if (ap->ops->error_handler) { + struct ata_eh_info *ehi = &ap->eh_info; + unsigned long flags; + + ata_port_probe(ap); + + /* kick EH for boot probing */ + spin_lock_irqsave(ap->lock, flags); + + ehi->probe_mask = (1 << ATA_MAX_DEVICES) - 1; + ehi->action |= ATA_EH_SOFTRESET; + ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET; + + ap->pflags |= ATA_PFLAG_LOADING; + ata_port_schedule_eh(ap); + + spin_unlock_irqrestore(ap->lock, flags); + + /* wait for EH to finish */ + ata_port_wait_eh(ap); + } else { + DPRINTK("ata%u: bus probe begin\n", ap->id); + rc = ata_bus_probe(ap); + DPRINTK("ata%u: bus probe end\n", ap->id); + + if (rc) { + /* FIXME: do something useful here? + * Current libata behavior will + * tear down everything when + * the module is removed + * or the h/w is unplugged. + */ + } + } + } + + /* probes are done, now scan each port's disk(s) */ + DPRINTK("host probe begin\n"); + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + + ata_scsi_scan_host(ap); + } + + dev_set_drvdata(dev, host); + + VPRINTK("EXIT, returning %u\n", ent->n_ports); + return ent->n_ports; /* success */ + +err_out_free_irq: + free_irq(ent->irq, host); +err_out: + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + if (ap) { + ap->ops->port_stop(ap); + scsi_host_put(ap->scsi_host); + } + } + + kfree(host); + VPRINTK("EXIT, returning 0\n"); + return 0; +} + +/** + * ata_port_detach - Detach ATA port in prepration of device removal + * @ap: ATA port to be detached + * + * Detach all ATA devices and the associated SCSI devices of @ap; + * then, remove the associated SCSI host. @ap is guaranteed to + * be quiescent on return from this function. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +void ata_port_detach(struct ata_port *ap) +{ + unsigned long flags; + int i; + + if (!ap->ops->error_handler) + goto skip_eh; + + /* tell EH we're leaving & flush EH */ + spin_lock_irqsave(ap->lock, flags); + ap->pflags |= ATA_PFLAG_UNLOADING; + spin_unlock_irqrestore(ap->lock, flags); + + ata_port_wait_eh(ap); + + /* EH is now guaranteed to see UNLOADING, so no new device + * will be attached. Disable all existing devices. + */ + spin_lock_irqsave(ap->lock, flags); + + for (i = 0; i < ATA_MAX_DEVICES; i++) + ata_dev_disable(&ap->device[i]); + + spin_unlock_irqrestore(ap->lock, flags); + + /* Final freeze & EH. All in-flight commands are aborted. EH + * will be skipped and retrials will be terminated with bad + * target. + */ + spin_lock_irqsave(ap->lock, flags); + ata_port_freeze(ap); /* won't be thawed */ + spin_unlock_irqrestore(ap->lock, flags); + + ata_port_wait_eh(ap); + + /* Flush hotplug task. The sequence is similar to + * ata_port_flush_task(). + */ + flush_workqueue(ata_aux_wq); + cancel_delayed_work(&ap->hotplug_task); + flush_workqueue(ata_aux_wq); + + skip_eh: + /* remove the associated SCSI host */ + scsi_remove_host(ap->scsi_host); +} + +/** + * ata_host_remove - PCI layer callback for device removal + * @host: ATA host set that was removed + * + * Unregister all objects associated with this host set. Free those + * objects. + * + * LOCKING: + * Inherited from calling layer (may sleep). + */ + +void ata_host_remove(struct ata_host *host) +{ + unsigned int i; + + for (i = 0; i < host->n_ports; i++) + ata_port_detach(host->ports[i]); + + free_irq(host->irq, host); + if (host->irq2) + free_irq(host->irq2, host); + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + + ata_scsi_release(ap->scsi_host); + + if ((ap->flags & ATA_FLAG_NO_LEGACY) == 0) { + struct ata_ioports *ioaddr = &ap->ioaddr; + + /* FIXME: Add -ac IDE pci mods to remove these special cases */ + if (ioaddr->cmd_addr == ATA_PRIMARY_CMD) + release_region(ATA_PRIMARY_CMD, 8); + else if (ioaddr->cmd_addr == ATA_SECONDARY_CMD) + release_region(ATA_SECONDARY_CMD, 8); + } + + scsi_host_put(ap->scsi_host); + } + + if (host->ops->host_stop) + host->ops->host_stop(host); + + kfree(host); +} + +/** + * ata_scsi_release - SCSI layer callback hook for host unload + * @host: libata host to be unloaded + * + * Performs all duties necessary to shut down a libata port... + * Kill port kthread, disable port, and release resources. + * + * LOCKING: + * Inherited from SCSI layer. + * + * RETURNS: + * One. + */ + +int ata_scsi_release(struct Scsi_Host *shost) +{ + struct ata_port *ap = ata_shost_to_port(shost); + + DPRINTK("ENTER\n"); + + ap->ops->port_disable(ap); + ap->ops->port_stop(ap); + + DPRINTK("EXIT\n"); + return 1; +} + +struct ata_probe_ent * +ata_probe_ent_alloc(struct device *dev, const struct ata_port_info *port) +{ + struct ata_probe_ent *probe_ent; + + probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL); + if (!probe_ent) { + printk(KERN_ERR DRV_NAME "(%s): out of memory\n", + kobject_name(&(dev->kobj))); + return NULL; + } + + INIT_LIST_HEAD(&probe_ent->node); + probe_ent->dev = dev; + + probe_ent->sht = port->sht; + probe_ent->port_flags = port->flags; + probe_ent->pio_mask = port->pio_mask; + probe_ent->mwdma_mask = port->mwdma_mask; + probe_ent->udma_mask = port->udma_mask; + probe_ent->port_ops = port->port_ops; + + return probe_ent; +} + +/** + * ata_std_ports - initialize ioaddr with standard port offsets. + * @ioaddr: IO address structure to be initialized + * + * Utility function which initializes data_addr, error_addr, + * feature_addr, nsect_addr, lbal_addr, lbam_addr, lbah_addr, + * device_addr, status_addr, and command_addr to standard offsets + * relative to cmd_addr. + * + * Does not set ctl_addr, altstatus_addr, bmdma_addr, or scr_addr. + */ + +void ata_std_ports(struct ata_ioports *ioaddr) +{ + ioaddr->data_addr = ioaddr->cmd_addr + ATA_REG_DATA; + ioaddr->error_addr = ioaddr->cmd_addr + ATA_REG_ERR; + ioaddr->feature_addr = ioaddr->cmd_addr + ATA_REG_FEATURE; + ioaddr->nsect_addr = ioaddr->cmd_addr + ATA_REG_NSECT; + ioaddr->lbal_addr = ioaddr->cmd_addr + ATA_REG_LBAL; + ioaddr->lbam_addr = ioaddr->cmd_addr + ATA_REG_LBAM; + ioaddr->lbah_addr = ioaddr->cmd_addr + ATA_REG_LBAH; + ioaddr->device_addr = ioaddr->cmd_addr + ATA_REG_DEVICE; + ioaddr->status_addr = ioaddr->cmd_addr + ATA_REG_STATUS; + ioaddr->command_addr = ioaddr->cmd_addr + ATA_REG_CMD; +} + + +#ifdef CONFIG_PCI + +void ata_pci_host_stop (struct ata_host *host) +{ + struct pci_dev *pdev = to_pci_dev(host->dev); + + pci_iounmap(pdev, host->mmio_base); +} + +/** + * ata_pci_remove_one - PCI layer callback for device removal + * @pdev: PCI device that was removed + * + * PCI layer indicates to libata via this hook that + * hot-unplug or module unload event has occurred. + * Handle this by unregistering all objects associated + * with this PCI device. Free those objects. Then finally + * release PCI resources and disable device. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + */ + +void ata_pci_remove_one (struct pci_dev *pdev) +{ + struct device *dev = pci_dev_to_dev(pdev); + struct ata_host *host = dev_get_drvdata(dev); + + ata_host_remove(host); + + pci_release_regions(pdev); + pci_disable_device(pdev); + dev_set_drvdata(dev, NULL); +} + +/* move to PCI subsystem */ +int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits) +{ + unsigned long tmp = 0; + + switch (bits->width) { + case 1: { + u8 tmp8 = 0; + pci_read_config_byte(pdev, bits->reg, &tmp8); + tmp = tmp8; + break; + } + case 2: { + u16 tmp16 = 0; + pci_read_config_word(pdev, bits->reg, &tmp16); + tmp = tmp16; + break; + } + case 4: { + u32 tmp32 = 0; + pci_read_config_dword(pdev, bits->reg, &tmp32); + tmp = tmp32; + break; + } + + default: + return -EINVAL; + } + + tmp &= bits->mask; + + return (tmp == bits->val) ? 1 : 0; +} + +void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg) +{ + pci_save_state(pdev); + + if (mesg.event == PM_EVENT_SUSPEND) { + pci_disable_device(pdev); + pci_set_power_state(pdev, PCI_D3hot); + } +} + +void ata_pci_device_do_resume(struct pci_dev *pdev) +{ + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + pci_enable_device(pdev); + pci_set_master(pdev); +} + +int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int rc = 0; + + rc = ata_host_suspend(host, mesg); + if (rc) + return rc; + + ata_pci_device_do_suspend(pdev, mesg); + + return 0; +} + +int ata_pci_device_resume(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + + ata_pci_device_do_resume(pdev); + ata_host_resume(host); + return 0; +} +#endif /* CONFIG_PCI */ + + +static int __init ata_init(void) +{ + ata_probe_timeout *= HZ; + ata_wq = create_workqueue("ata"); + if (!ata_wq) + return -ENOMEM; + + ata_aux_wq = create_singlethread_workqueue("ata_aux"); + if (!ata_aux_wq) { + destroy_workqueue(ata_wq); + return -ENOMEM; + } + + printk(KERN_DEBUG "libata version " DRV_VERSION " loaded.\n"); + return 0; +} + +static void __exit ata_exit(void) +{ + destroy_workqueue(ata_wq); + destroy_workqueue(ata_aux_wq); +} + +module_init(ata_init); +module_exit(ata_exit); + +static unsigned long ratelimit_time; +static DEFINE_SPINLOCK(ata_ratelimit_lock); + +int ata_ratelimit(void) +{ + int rc; + unsigned long flags; + + spin_lock_irqsave(&ata_ratelimit_lock, flags); + + if (time_after(jiffies, ratelimit_time)) { + rc = 1; + ratelimit_time = jiffies + (HZ/5); + } else + rc = 0; + + spin_unlock_irqrestore(&ata_ratelimit_lock, flags); + + return rc; +} + +/** + * ata_wait_register - wait until register value changes + * @reg: IO-mapped register + * @mask: Mask to apply to read register value + * @val: Wait condition + * @interval_msec: polling interval in milliseconds + * @timeout_msec: timeout in milliseconds + * + * Waiting for some bits of register to change is a common + * operation for ATA controllers. This function reads 32bit LE + * IO-mapped register @reg and tests for the following condition. + * + * (*@reg & mask) != val + * + * If the condition is met, it returns; otherwise, the process is + * repeated after @interval_msec until timeout. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * The final register value. + */ +u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val, + unsigned long interval_msec, + unsigned long timeout_msec) +{ + unsigned long timeout; + u32 tmp; + + tmp = ioread32(reg); + + /* Calculate timeout _after_ the first read to make sure + * preceding writes reach the controller before starting to + * eat away the timeout. + */ + timeout = jiffies + (timeout_msec * HZ) / 1000; + + while ((tmp & mask) == val && time_before(jiffies, timeout)) { + msleep(interval_msec); + tmp = ioread32(reg); + } + + return tmp; +} + +/* + * Dummy port_ops + */ +static void ata_dummy_noret(struct ata_port *ap) { } +static int ata_dummy_ret0(struct ata_port *ap) { return 0; } +static void ata_dummy_qc_noret(struct ata_queued_cmd *qc) { } + +static u8 ata_dummy_check_status(struct ata_port *ap) +{ + return ATA_DRDY; +} + +static unsigned int ata_dummy_qc_issue(struct ata_queued_cmd *qc) +{ + return AC_ERR_SYSTEM; +} + +const struct ata_port_operations ata_dummy_port_ops = { + .port_disable = ata_port_disable, + .check_status = ata_dummy_check_status, + .check_altstatus = ata_dummy_check_status, + .dev_select = ata_noop_dev_select, + .qc_prep = ata_noop_qc_prep, + .qc_issue = ata_dummy_qc_issue, + .freeze = ata_dummy_noret, + .thaw = ata_dummy_noret, + .error_handler = ata_dummy_noret, + .post_internal_cmd = ata_dummy_qc_noret, + .irq_clear = ata_dummy_noret, + .port_start = ata_dummy_ret0, + .port_stop = ata_dummy_noret, +}; + +/* + * libata is essentially a library of internal helper functions for + * low-level ATA host controller drivers. As such, the API/ABI is + * likely to change as new drivers are added and updated. + * Do not depend on ABI/API stability. + */ + +EXPORT_SYMBOL_GPL(sata_deb_timing_normal); +EXPORT_SYMBOL_GPL(sata_deb_timing_hotplug); +EXPORT_SYMBOL_GPL(sata_deb_timing_long); +EXPORT_SYMBOL_GPL(ata_dummy_port_ops); +EXPORT_SYMBOL_GPL(ata_std_bios_param); +EXPORT_SYMBOL_GPL(ata_std_ports); +EXPORT_SYMBOL_GPL(ata_host_init); +EXPORT_SYMBOL_GPL(ata_device_add); +EXPORT_SYMBOL_GPL(ata_port_detach); +EXPORT_SYMBOL_GPL(ata_host_remove); +EXPORT_SYMBOL_GPL(ata_sg_init); +EXPORT_SYMBOL_GPL(ata_sg_init_one); +EXPORT_SYMBOL_GPL(ata_hsm_move); +EXPORT_SYMBOL_GPL(ata_qc_complete); +EXPORT_SYMBOL_GPL(ata_qc_complete_multiple); +EXPORT_SYMBOL_GPL(ata_qc_issue_prot); +EXPORT_SYMBOL_GPL(ata_tf_load); +EXPORT_SYMBOL_GPL(ata_tf_read); +EXPORT_SYMBOL_GPL(ata_noop_dev_select); +EXPORT_SYMBOL_GPL(ata_std_dev_select); +EXPORT_SYMBOL_GPL(ata_tf_to_fis); +EXPORT_SYMBOL_GPL(ata_tf_from_fis); +EXPORT_SYMBOL_GPL(ata_check_status); +EXPORT_SYMBOL_GPL(ata_altstatus); +EXPORT_SYMBOL_GPL(ata_exec_command); +EXPORT_SYMBOL_GPL(ata_port_start); +EXPORT_SYMBOL_GPL(ata_port_stop); +EXPORT_SYMBOL_GPL(ata_host_stop); +EXPORT_SYMBOL_GPL(ata_interrupt); +EXPORT_SYMBOL_GPL(ata_mmio_data_xfer); +EXPORT_SYMBOL_GPL(ata_pio_data_xfer); +EXPORT_SYMBOL_GPL(ata_pio_data_xfer_noirq); +EXPORT_SYMBOL_GPL(ata_qc_prep); +EXPORT_SYMBOL_GPL(ata_noop_qc_prep); +EXPORT_SYMBOL_GPL(ata_bmdma_setup); +EXPORT_SYMBOL_GPL(ata_bmdma_start); +EXPORT_SYMBOL_GPL(ata_bmdma_irq_clear); +EXPORT_SYMBOL_GPL(ata_bmdma_status); +EXPORT_SYMBOL_GPL(ata_bmdma_stop); +EXPORT_SYMBOL_GPL(ata_bmdma_freeze); +EXPORT_SYMBOL_GPL(ata_bmdma_thaw); +EXPORT_SYMBOL_GPL(ata_bmdma_drive_eh); +EXPORT_SYMBOL_GPL(ata_bmdma_error_handler); +EXPORT_SYMBOL_GPL(ata_bmdma_post_internal_cmd); +EXPORT_SYMBOL_GPL(ata_port_probe); +EXPORT_SYMBOL_GPL(sata_set_spd); +EXPORT_SYMBOL_GPL(sata_phy_debounce); +EXPORT_SYMBOL_GPL(sata_phy_resume); +EXPORT_SYMBOL_GPL(sata_phy_reset); +EXPORT_SYMBOL_GPL(__sata_phy_reset); +EXPORT_SYMBOL_GPL(ata_bus_reset); +EXPORT_SYMBOL_GPL(ata_std_prereset); +EXPORT_SYMBOL_GPL(ata_std_softreset); +EXPORT_SYMBOL_GPL(sata_std_hardreset); +EXPORT_SYMBOL_GPL(ata_std_postreset); +EXPORT_SYMBOL_GPL(ata_dev_revalidate); +EXPORT_SYMBOL_GPL(ata_dev_classify); +EXPORT_SYMBOL_GPL(ata_dev_pair); +EXPORT_SYMBOL_GPL(ata_port_disable); +EXPORT_SYMBOL_GPL(ata_ratelimit); +EXPORT_SYMBOL_GPL(ata_wait_register); +EXPORT_SYMBOL_GPL(ata_busy_sleep); +EXPORT_SYMBOL_GPL(ata_port_queue_task); +EXPORT_SYMBOL_GPL(ata_scsi_ioctl); +EXPORT_SYMBOL_GPL(ata_scsi_queuecmd); +EXPORT_SYMBOL_GPL(ata_scsi_slave_config); +EXPORT_SYMBOL_GPL(ata_scsi_slave_destroy); +EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth); +EXPORT_SYMBOL_GPL(ata_scsi_release); +EXPORT_SYMBOL_GPL(ata_host_intr); +EXPORT_SYMBOL_GPL(sata_scr_valid); +EXPORT_SYMBOL_GPL(sata_scr_read); +EXPORT_SYMBOL_GPL(sata_scr_write); +EXPORT_SYMBOL_GPL(sata_scr_write_flush); +EXPORT_SYMBOL_GPL(ata_port_online); +EXPORT_SYMBOL_GPL(ata_port_offline); +EXPORT_SYMBOL_GPL(ata_host_suspend); +EXPORT_SYMBOL_GPL(ata_host_resume); +EXPORT_SYMBOL_GPL(ata_id_string); +EXPORT_SYMBOL_GPL(ata_id_c_string); +EXPORT_SYMBOL_GPL(ata_scsi_simulate); + +EXPORT_SYMBOL_GPL(ata_pio_need_iordy); +EXPORT_SYMBOL_GPL(ata_timing_compute); +EXPORT_SYMBOL_GPL(ata_timing_merge); + +#ifdef CONFIG_PCI +EXPORT_SYMBOL_GPL(pci_test_config_bits); +EXPORT_SYMBOL_GPL(ata_pci_host_stop); +EXPORT_SYMBOL_GPL(ata_pci_init_native_mode); +EXPORT_SYMBOL_GPL(ata_pci_init_one); +EXPORT_SYMBOL_GPL(ata_pci_remove_one); +EXPORT_SYMBOL_GPL(ata_pci_device_do_suspend); +EXPORT_SYMBOL_GPL(ata_pci_device_do_resume); +EXPORT_SYMBOL_GPL(ata_pci_device_suspend); +EXPORT_SYMBOL_GPL(ata_pci_device_resume); +EXPORT_SYMBOL_GPL(ata_pci_default_filter); +EXPORT_SYMBOL_GPL(ata_pci_clear_simplex); +#endif /* CONFIG_PCI */ + +EXPORT_SYMBOL_GPL(ata_scsi_device_suspend); +EXPORT_SYMBOL_GPL(ata_scsi_device_resume); + +EXPORT_SYMBOL_GPL(ata_eng_timeout); +EXPORT_SYMBOL_GPL(ata_port_schedule_eh); +EXPORT_SYMBOL_GPL(ata_port_abort); +EXPORT_SYMBOL_GPL(ata_port_freeze); +EXPORT_SYMBOL_GPL(ata_eh_freeze_port); +EXPORT_SYMBOL_GPL(ata_eh_thaw_port); +EXPORT_SYMBOL_GPL(ata_eh_qc_complete); +EXPORT_SYMBOL_GPL(ata_eh_qc_retry); +EXPORT_SYMBOL_GPL(ata_do_eh); diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c new file mode 100644 index 00000000000..02b2b2787d9 --- /dev/null +++ b/drivers/ata/libata-eh.c @@ -0,0 +1,2249 @@ +/* + * libata-eh.c - libata error handling + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2006 Tejun Heo <htejun@gmail.com> + * + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, + * USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available from http://www.t13.org/ and + * http://www.sata-io.org/ + * + */ + +#include <linux/kernel.h> +#include <scsi/scsi.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_eh.h> +#include <scsi/scsi_device.h> +#include <scsi/scsi_cmnd.h> +#include "../scsi/scsi_transport_api.h" + +#include <linux/libata.h> + +#include "libata.h" + +static void __ata_port_freeze(struct ata_port *ap); +static void ata_eh_finish(struct ata_port *ap); +static void ata_eh_handle_port_suspend(struct ata_port *ap); +static void ata_eh_handle_port_resume(struct ata_port *ap); + +static void ata_ering_record(struct ata_ering *ering, int is_io, + unsigned int err_mask) +{ + struct ata_ering_entry *ent; + + WARN_ON(!err_mask); + + ering->cursor++; + ering->cursor %= ATA_ERING_SIZE; + + ent = &ering->ring[ering->cursor]; + ent->is_io = is_io; + ent->err_mask = err_mask; + ent->timestamp = get_jiffies_64(); +} + +static struct ata_ering_entry * ata_ering_top(struct ata_ering *ering) +{ + struct ata_ering_entry *ent = &ering->ring[ering->cursor]; + if (!ent->err_mask) + return NULL; + return ent; +} + +static int ata_ering_map(struct ata_ering *ering, + int (*map_fn)(struct ata_ering_entry *, void *), + void *arg) +{ + int idx, rc = 0; + struct ata_ering_entry *ent; + + idx = ering->cursor; + do { + ent = &ering->ring[idx]; + if (!ent->err_mask) + break; + rc = map_fn(ent, arg); + if (rc) + break; + idx = (idx - 1 + ATA_ERING_SIZE) % ATA_ERING_SIZE; + } while (idx != ering->cursor); + + return rc; +} + +static unsigned int ata_eh_dev_action(struct ata_device *dev) +{ + struct ata_eh_context *ehc = &dev->ap->eh_context; + + return ehc->i.action | ehc->i.dev_action[dev->devno]; +} + +static void ata_eh_clear_action(struct ata_device *dev, + struct ata_eh_info *ehi, unsigned int action) +{ + int i; + + if (!dev) { + ehi->action &= ~action; + for (i = 0; i < ATA_MAX_DEVICES; i++) + ehi->dev_action[i] &= ~action; + } else { + /* doesn't make sense for port-wide EH actions */ + WARN_ON(!(action & ATA_EH_PERDEV_MASK)); + + /* break ehi->action into ehi->dev_action */ + if (ehi->action & action) { + for (i = 0; i < ATA_MAX_DEVICES; i++) + ehi->dev_action[i] |= ehi->action & action; + ehi->action &= ~action; + } + + /* turn off the specified per-dev action */ + ehi->dev_action[dev->devno] &= ~action; + } +} + +/** + * ata_scsi_timed_out - SCSI layer time out callback + * @cmd: timed out SCSI command + * + * Handles SCSI layer timeout. We race with normal completion of + * the qc for @cmd. If the qc is already gone, we lose and let + * the scsi command finish (EH_HANDLED). Otherwise, the qc has + * timed out and EH should be invoked. Prevent ata_qc_complete() + * from finishing it by setting EH_SCHEDULED and return + * EH_NOT_HANDLED. + * + * TODO: kill this function once old EH is gone. + * + * LOCKING: + * Called from timer context + * + * RETURNS: + * EH_HANDLED or EH_NOT_HANDLED + */ +enum scsi_eh_timer_return ata_scsi_timed_out(struct scsi_cmnd *cmd) +{ + struct Scsi_Host *host = cmd->device->host; + struct ata_port *ap = ata_shost_to_port(host); + unsigned long flags; + struct ata_queued_cmd *qc; + enum scsi_eh_timer_return ret; + + DPRINTK("ENTER\n"); + + if (ap->ops->error_handler) { + ret = EH_NOT_HANDLED; + goto out; + } + + ret = EH_HANDLED; + spin_lock_irqsave(ap->lock, flags); + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc) { + WARN_ON(qc->scsicmd != cmd); + qc->flags |= ATA_QCFLAG_EH_SCHEDULED; + qc->err_mask |= AC_ERR_TIMEOUT; + ret = EH_NOT_HANDLED; + } + spin_unlock_irqrestore(ap->lock, flags); + + out: + DPRINTK("EXIT, ret=%d\n", ret); + return ret; +} + +/** + * ata_scsi_error - SCSI layer error handler callback + * @host: SCSI host on which error occurred + * + * Handles SCSI-layer-thrown error events. + * + * LOCKING: + * Inherited from SCSI layer (none, can sleep) + * + * RETURNS: + * Zero. + */ +void ata_scsi_error(struct Scsi_Host *host) +{ + struct ata_port *ap = ata_shost_to_port(host); + int i, repeat_cnt = ATA_EH_MAX_REPEAT; + unsigned long flags; + + DPRINTK("ENTER\n"); + + /* synchronize with port task */ + ata_port_flush_task(ap); + + /* synchronize with host lock and sort out timeouts */ + + /* For new EH, all qcs are finished in one of three ways - + * normal completion, error completion, and SCSI timeout. + * Both cmpletions can race against SCSI timeout. When normal + * completion wins, the qc never reaches EH. When error + * completion wins, the qc has ATA_QCFLAG_FAILED set. + * + * When SCSI timeout wins, things are a bit more complex. + * Normal or error completion can occur after the timeout but + * before this point. In such cases, both types of + * completions are honored. A scmd is determined to have + * timed out iff its associated qc is active and not failed. + */ + if (ap->ops->error_handler) { + struct scsi_cmnd *scmd, *tmp; + int nr_timedout = 0; + + spin_lock_irqsave(ap->lock, flags); + + list_for_each_entry_safe(scmd, tmp, &host->eh_cmd_q, eh_entry) { + struct ata_queued_cmd *qc; + + for (i = 0; i < ATA_MAX_QUEUE; i++) { + qc = __ata_qc_from_tag(ap, i); + if (qc->flags & ATA_QCFLAG_ACTIVE && + qc->scsicmd == scmd) + break; + } + + if (i < ATA_MAX_QUEUE) { + /* the scmd has an associated qc */ + if (!(qc->flags & ATA_QCFLAG_FAILED)) { + /* which hasn't failed yet, timeout */ + qc->err_mask |= AC_ERR_TIMEOUT; + qc->flags |= ATA_QCFLAG_FAILED; + nr_timedout++; + } + } else { + /* Normal completion occurred after + * SCSI timeout but before this point. + * Successfully complete it. + */ + scmd->retries = scmd->allowed; + scsi_eh_finish_cmd(scmd, &ap->eh_done_q); + } + } + + /* If we have timed out qcs. They belong to EH from + * this point but the state of the controller is + * unknown. Freeze the port to make sure the IRQ + * handler doesn't diddle with those qcs. This must + * be done atomically w.r.t. setting QCFLAG_FAILED. + */ + if (nr_timedout) + __ata_port_freeze(ap); + + spin_unlock_irqrestore(ap->lock, flags); + } else + spin_unlock_wait(ap->lock); + + repeat: + /* invoke error handler */ + if (ap->ops->error_handler) { + /* process port resume request */ + ata_eh_handle_port_resume(ap); + + /* fetch & clear EH info */ + spin_lock_irqsave(ap->lock, flags); + + memset(&ap->eh_context, 0, sizeof(ap->eh_context)); + ap->eh_context.i = ap->eh_info; + memset(&ap->eh_info, 0, sizeof(ap->eh_info)); + + ap->pflags |= ATA_PFLAG_EH_IN_PROGRESS; + ap->pflags &= ~ATA_PFLAG_EH_PENDING; + + spin_unlock_irqrestore(ap->lock, flags); + + /* invoke EH, skip if unloading or suspended */ + if (!(ap->pflags & (ATA_PFLAG_UNLOADING | ATA_PFLAG_SUSPENDED))) + ap->ops->error_handler(ap); + else + ata_eh_finish(ap); + + /* process port suspend request */ + ata_eh_handle_port_suspend(ap); + + /* Exception might have happend after ->error_handler + * recovered the port but before this point. Repeat + * EH in such case. + */ + spin_lock_irqsave(ap->lock, flags); + + if (ap->pflags & ATA_PFLAG_EH_PENDING) { + if (--repeat_cnt) { + ata_port_printk(ap, KERN_INFO, + "EH pending after completion, " + "repeating EH (cnt=%d)\n", repeat_cnt); + spin_unlock_irqrestore(ap->lock, flags); + goto repeat; + } + ata_port_printk(ap, KERN_ERR, "EH pending after %d " + "tries, giving up\n", ATA_EH_MAX_REPEAT); + } + + /* this run is complete, make sure EH info is clear */ + memset(&ap->eh_info, 0, sizeof(ap->eh_info)); + + /* Clear host_eh_scheduled while holding ap->lock such + * that if exception occurs after this point but + * before EH completion, SCSI midlayer will + * re-initiate EH. + */ + host->host_eh_scheduled = 0; + + spin_unlock_irqrestore(ap->lock, flags); + } else { + WARN_ON(ata_qc_from_tag(ap, ap->active_tag) == NULL); + ap->ops->eng_timeout(ap); + } + + /* finish or retry handled scmd's and clean up */ + WARN_ON(host->host_failed || !list_empty(&host->eh_cmd_q)); + + scsi_eh_flush_done_q(&ap->eh_done_q); + + /* clean up */ + spin_lock_irqsave(ap->lock, flags); + + if (ap->pflags & ATA_PFLAG_LOADING) + ap->pflags &= ~ATA_PFLAG_LOADING; + else if (ap->pflags & ATA_PFLAG_SCSI_HOTPLUG) + queue_work(ata_aux_wq, &ap->hotplug_task); + + if (ap->pflags & ATA_PFLAG_RECOVERED) + ata_port_printk(ap, KERN_INFO, "EH complete\n"); + + ap->pflags &= ~(ATA_PFLAG_SCSI_HOTPLUG | ATA_PFLAG_RECOVERED); + + /* tell wait_eh that we're done */ + ap->pflags &= ~ATA_PFLAG_EH_IN_PROGRESS; + wake_up_all(&ap->eh_wait_q); + + spin_unlock_irqrestore(ap->lock, flags); + + DPRINTK("EXIT\n"); +} + +/** + * ata_port_wait_eh - Wait for the currently pending EH to complete + * @ap: Port to wait EH for + * + * Wait until the currently pending EH is complete. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +void ata_port_wait_eh(struct ata_port *ap) +{ + unsigned long flags; + DEFINE_WAIT(wait); + + retry: + spin_lock_irqsave(ap->lock, flags); + + while (ap->pflags & (ATA_PFLAG_EH_PENDING | ATA_PFLAG_EH_IN_PROGRESS)) { + prepare_to_wait(&ap->eh_wait_q, &wait, TASK_UNINTERRUPTIBLE); + spin_unlock_irqrestore(ap->lock, flags); + schedule(); + spin_lock_irqsave(ap->lock, flags); + } + finish_wait(&ap->eh_wait_q, &wait); + + spin_unlock_irqrestore(ap->lock, flags); + + /* make sure SCSI EH is complete */ + if (scsi_host_in_recovery(ap->scsi_host)) { + msleep(10); + goto retry; + } +} + +/** + * ata_qc_timeout - Handle timeout of queued command + * @qc: Command that timed out + * + * Some part of the kernel (currently, only the SCSI layer) + * has noticed that the active command on port @ap has not + * completed after a specified length of time. Handle this + * condition by disabling DMA (if necessary) and completing + * transactions, with error if necessary. + * + * This also handles the case of the "lost interrupt", where + * for some reason (possibly hardware bug, possibly driver bug) + * an interrupt was not delivered to the driver, even though the + * transaction completed successfully. + * + * TODO: kill this function once old EH is gone. + * + * LOCKING: + * Inherited from SCSI layer (none, can sleep) + */ +static void ata_qc_timeout(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + u8 host_stat = 0, drv_stat; + unsigned long flags; + + DPRINTK("ENTER\n"); + + ap->hsm_task_state = HSM_ST_IDLE; + + spin_lock_irqsave(ap->lock, flags); + + switch (qc->tf.protocol) { + + case ATA_PROT_DMA: + case ATA_PROT_ATAPI_DMA: + host_stat = ap->ops->bmdma_status(ap); + + /* before we do anything else, clear DMA-Start bit */ + ap->ops->bmdma_stop(qc); + + /* fall through */ + + default: + ata_altstatus(ap); + drv_stat = ata_chk_status(ap); + + /* ack bmdma irq events */ + ap->ops->irq_clear(ap); + + ata_dev_printk(qc->dev, KERN_ERR, "command 0x%x timeout, " + "stat 0x%x host_stat 0x%x\n", + qc->tf.command, drv_stat, host_stat); + + /* complete taskfile transaction */ + qc->err_mask |= AC_ERR_TIMEOUT; + break; + } + + spin_unlock_irqrestore(ap->lock, flags); + + ata_eh_qc_complete(qc); + + DPRINTK("EXIT\n"); +} + +/** + * ata_eng_timeout - Handle timeout of queued command + * @ap: Port on which timed-out command is active + * + * Some part of the kernel (currently, only the SCSI layer) + * has noticed that the active command on port @ap has not + * completed after a specified length of time. Handle this + * condition by disabling DMA (if necessary) and completing + * transactions, with error if necessary. + * + * This also handles the case of the "lost interrupt", where + * for some reason (possibly hardware bug, possibly driver bug) + * an interrupt was not delivered to the driver, even though the + * transaction completed successfully. + * + * TODO: kill this function once old EH is gone. + * + * LOCKING: + * Inherited from SCSI layer (none, can sleep) + */ +void ata_eng_timeout(struct ata_port *ap) +{ + DPRINTK("ENTER\n"); + + ata_qc_timeout(ata_qc_from_tag(ap, ap->active_tag)); + + DPRINTK("EXIT\n"); +} + +/** + * ata_qc_schedule_eh - schedule qc for error handling + * @qc: command to schedule error handling for + * + * Schedule error handling for @qc. EH will kick in as soon as + * other commands are drained. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_qc_schedule_eh(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + WARN_ON(!ap->ops->error_handler); + + qc->flags |= ATA_QCFLAG_FAILED; + qc->ap->pflags |= ATA_PFLAG_EH_PENDING; + + /* The following will fail if timeout has already expired. + * ata_scsi_error() takes care of such scmds on EH entry. + * Note that ATA_QCFLAG_FAILED is unconditionally set after + * this function completes. + */ + scsi_req_abort_cmd(qc->scsicmd); +} + +/** + * ata_port_schedule_eh - schedule error handling without a qc + * @ap: ATA port to schedule EH for + * + * Schedule error handling for @ap. EH will kick in as soon as + * all commands are drained. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_port_schedule_eh(struct ata_port *ap) +{ + WARN_ON(!ap->ops->error_handler); + + ap->pflags |= ATA_PFLAG_EH_PENDING; + scsi_schedule_eh(ap->scsi_host); + + DPRINTK("port EH scheduled\n"); +} + +/** + * ata_port_abort - abort all qc's on the port + * @ap: ATA port to abort qc's for + * + * Abort all active qc's of @ap and schedule EH. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Number of aborted qc's. + */ +int ata_port_abort(struct ata_port *ap) +{ + int tag, nr_aborted = 0; + + WARN_ON(!ap->ops->error_handler); + + for (tag = 0; tag < ATA_MAX_QUEUE; tag++) { + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, tag); + + if (qc) { + qc->flags |= ATA_QCFLAG_FAILED; + ata_qc_complete(qc); + nr_aborted++; + } + } + + if (!nr_aborted) + ata_port_schedule_eh(ap); + + return nr_aborted; +} + +/** + * __ata_port_freeze - freeze port + * @ap: ATA port to freeze + * + * This function is called when HSM violation or some other + * condition disrupts normal operation of the port. Frozen port + * is not allowed to perform any operation until the port is + * thawed, which usually follows a successful reset. + * + * ap->ops->freeze() callback can be used for freezing the port + * hardware-wise (e.g. mask interrupt and stop DMA engine). If a + * port cannot be frozen hardware-wise, the interrupt handler + * must ack and clear interrupts unconditionally while the port + * is frozen. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +static void __ata_port_freeze(struct ata_port *ap) +{ + WARN_ON(!ap->ops->error_handler); + + if (ap->ops->freeze) + ap->ops->freeze(ap); + + ap->pflags |= ATA_PFLAG_FROZEN; + + DPRINTK("ata%u port frozen\n", ap->id); +} + +/** + * ata_port_freeze - abort & freeze port + * @ap: ATA port to freeze + * + * Abort and freeze @ap. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Number of aborted commands. + */ +int ata_port_freeze(struct ata_port *ap) +{ + int nr_aborted; + + WARN_ON(!ap->ops->error_handler); + + nr_aborted = ata_port_abort(ap); + __ata_port_freeze(ap); + + return nr_aborted; +} + +/** + * ata_eh_freeze_port - EH helper to freeze port + * @ap: ATA port to freeze + * + * Freeze @ap. + * + * LOCKING: + * None. + */ +void ata_eh_freeze_port(struct ata_port *ap) +{ + unsigned long flags; + + if (!ap->ops->error_handler) + return; + + spin_lock_irqsave(ap->lock, flags); + __ata_port_freeze(ap); + spin_unlock_irqrestore(ap->lock, flags); +} + +/** + * ata_port_thaw_port - EH helper to thaw port + * @ap: ATA port to thaw + * + * Thaw frozen port @ap. + * + * LOCKING: + * None. + */ +void ata_eh_thaw_port(struct ata_port *ap) +{ + unsigned long flags; + + if (!ap->ops->error_handler) + return; + + spin_lock_irqsave(ap->lock, flags); + + ap->pflags &= ~ATA_PFLAG_FROZEN; + + if (ap->ops->thaw) + ap->ops->thaw(ap); + + spin_unlock_irqrestore(ap->lock, flags); + + DPRINTK("ata%u port thawed\n", ap->id); +} + +static void ata_eh_scsidone(struct scsi_cmnd *scmd) +{ + /* nada */ +} + +static void __ata_eh_qc_complete(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct scsi_cmnd *scmd = qc->scsicmd; + unsigned long flags; + + spin_lock_irqsave(ap->lock, flags); + qc->scsidone = ata_eh_scsidone; + __ata_qc_complete(qc); + WARN_ON(ata_tag_valid(qc->tag)); + spin_unlock_irqrestore(ap->lock, flags); + + scsi_eh_finish_cmd(scmd, &ap->eh_done_q); +} + +/** + * ata_eh_qc_complete - Complete an active ATA command from EH + * @qc: Command to complete + * + * Indicate to the mid and upper layers that an ATA command has + * completed. To be used from EH. + */ +void ata_eh_qc_complete(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *scmd = qc->scsicmd; + scmd->retries = scmd->allowed; + __ata_eh_qc_complete(qc); +} + +/** + * ata_eh_qc_retry - Tell midlayer to retry an ATA command after EH + * @qc: Command to retry + * + * Indicate to the mid and upper layers that an ATA command + * should be retried. To be used from EH. + * + * SCSI midlayer limits the number of retries to scmd->allowed. + * scmd->retries is decremented for commands which get retried + * due to unrelated failures (qc->err_mask is zero). + */ +void ata_eh_qc_retry(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *scmd = qc->scsicmd; + if (!qc->err_mask && scmd->retries) + scmd->retries--; + __ata_eh_qc_complete(qc); +} + +/** + * ata_eh_detach_dev - detach ATA device + * @dev: ATA device to detach + * + * Detach @dev. + * + * LOCKING: + * None. + */ +static void ata_eh_detach_dev(struct ata_device *dev) +{ + struct ata_port *ap = dev->ap; + unsigned long flags; + + ata_dev_disable(dev); + + spin_lock_irqsave(ap->lock, flags); + + dev->flags &= ~ATA_DFLAG_DETACH; + + if (ata_scsi_offline_dev(dev)) { + dev->flags |= ATA_DFLAG_DETACHED; + ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG; + } + + /* clear per-dev EH actions */ + ata_eh_clear_action(dev, &ap->eh_info, ATA_EH_PERDEV_MASK); + ata_eh_clear_action(dev, &ap->eh_context.i, ATA_EH_PERDEV_MASK); + + spin_unlock_irqrestore(ap->lock, flags); +} + +/** + * ata_eh_about_to_do - about to perform eh_action + * @ap: target ATA port + * @dev: target ATA dev for per-dev action (can be NULL) + * @action: action about to be performed + * + * Called just before performing EH actions to clear related bits + * in @ap->eh_info such that eh actions are not unnecessarily + * repeated. + * + * LOCKING: + * None. + */ +static void ata_eh_about_to_do(struct ata_port *ap, struct ata_device *dev, + unsigned int action) +{ + unsigned long flags; + struct ata_eh_info *ehi = &ap->eh_info; + struct ata_eh_context *ehc = &ap->eh_context; + + spin_lock_irqsave(ap->lock, flags); + + /* Reset is represented by combination of actions and EHI + * flags. Suck in all related bits before clearing eh_info to + * avoid losing requested action. + */ + if (action & ATA_EH_RESET_MASK) { + ehc->i.action |= ehi->action & ATA_EH_RESET_MASK; + ehc->i.flags |= ehi->flags & ATA_EHI_RESET_MODIFIER_MASK; + + /* make sure all reset actions are cleared & clear EHI flags */ + action |= ATA_EH_RESET_MASK; + ehi->flags &= ~ATA_EHI_RESET_MODIFIER_MASK; + } + + ata_eh_clear_action(dev, ehi, action); + + if (!(ehc->i.flags & ATA_EHI_QUIET)) + ap->pflags |= ATA_PFLAG_RECOVERED; + + spin_unlock_irqrestore(ap->lock, flags); +} + +/** + * ata_eh_done - EH action complete + * @ap: target ATA port + * @dev: target ATA dev for per-dev action (can be NULL) + * @action: action just completed + * + * Called right after performing EH actions to clear related bits + * in @ap->eh_context. + * + * LOCKING: + * None. + */ +static void ata_eh_done(struct ata_port *ap, struct ata_device *dev, + unsigned int action) +{ + /* if reset is complete, clear all reset actions & reset modifier */ + if (action & ATA_EH_RESET_MASK) { + action |= ATA_EH_RESET_MASK; + ap->eh_context.i.flags &= ~ATA_EHI_RESET_MODIFIER_MASK; + } + + ata_eh_clear_action(dev, &ap->eh_context.i, action); +} + +/** + * ata_err_string - convert err_mask to descriptive string + * @err_mask: error mask to convert to string + * + * Convert @err_mask to descriptive string. Errors are + * prioritized according to severity and only the most severe + * error is reported. + * + * LOCKING: + * None. + * + * RETURNS: + * Descriptive string for @err_mask + */ +static const char * ata_err_string(unsigned int err_mask) +{ + if (err_mask & AC_ERR_HOST_BUS) + return "host bus error"; + if (err_mask & AC_ERR_ATA_BUS) + return "ATA bus error"; + if (err_mask & AC_ERR_TIMEOUT) + return "timeout"; + if (err_mask & AC_ERR_HSM) + return "HSM violation"; + if (err_mask & AC_ERR_SYSTEM) + return "internal error"; + if (err_mask & AC_ERR_MEDIA) + return "media error"; + if (err_mask & AC_ERR_INVALID) + return "invalid argument"; + if (err_mask & AC_ERR_DEV) + return "device error"; + return "unknown error"; +} + +/** + * ata_read_log_page - read a specific log page + * @dev: target device + * @page: page to read + * @buf: buffer to store read page + * @sectors: number of sectors to read + * + * Read log page using READ_LOG_EXT command. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, AC_ERR_* mask otherwise. + */ +static unsigned int ata_read_log_page(struct ata_device *dev, + u8 page, void *buf, unsigned int sectors) +{ + struct ata_taskfile tf; + unsigned int err_mask; + + DPRINTK("read log page - page %d\n", page); + + ata_tf_init(dev, &tf); + tf.command = ATA_CMD_READ_LOG_EXT; + tf.lbal = page; + tf.nsect = sectors; + tf.hob_nsect = sectors >> 8; + tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_LBA48 | ATA_TFLAG_DEVICE; + tf.protocol = ATA_PROT_PIO; + + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE, + buf, sectors * ATA_SECT_SIZE); + + DPRINTK("EXIT, err_mask=%x\n", err_mask); + return err_mask; +} + +/** + * ata_eh_read_log_10h - Read log page 10h for NCQ error details + * @dev: Device to read log page 10h from + * @tag: Resulting tag of the failed command + * @tf: Resulting taskfile registers of the failed command + * + * Read log page 10h to obtain NCQ error details and clear error + * condition. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +static int ata_eh_read_log_10h(struct ata_device *dev, + int *tag, struct ata_taskfile *tf) +{ + u8 *buf = dev->ap->sector_buf; + unsigned int err_mask; + u8 csum; + int i; + + err_mask = ata_read_log_page(dev, ATA_LOG_SATA_NCQ, buf, 1); + if (err_mask) + return -EIO; + + csum = 0; + for (i = 0; i < ATA_SECT_SIZE; i++) + csum += buf[i]; + if (csum) + ata_dev_printk(dev, KERN_WARNING, + "invalid checksum 0x%x on log page 10h\n", csum); + + if (buf[0] & 0x80) + return -ENOENT; + + *tag = buf[0] & 0x1f; + + tf->command = buf[2]; + tf->feature = buf[3]; + tf->lbal = buf[4]; + tf->lbam = buf[5]; + tf->lbah = buf[6]; + tf->device = buf[7]; + tf->hob_lbal = buf[8]; + tf->hob_lbam = buf[9]; + tf->hob_lbah = buf[10]; + tf->nsect = buf[12]; + tf->hob_nsect = buf[13]; + + return 0; +} + +/** + * atapi_eh_request_sense - perform ATAPI REQUEST_SENSE + * @dev: device to perform REQUEST_SENSE to + * @sense_buf: result sense data buffer (SCSI_SENSE_BUFFERSIZE bytes long) + * + * Perform ATAPI REQUEST_SENSE after the device reported CHECK + * SENSE. This function is EH helper. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, AC_ERR_* mask on failure + */ +static unsigned int atapi_eh_request_sense(struct ata_device *dev, + unsigned char *sense_buf) +{ + struct ata_port *ap = dev->ap; + struct ata_taskfile tf; + u8 cdb[ATAPI_CDB_LEN]; + + DPRINTK("ATAPI request sense\n"); + + ata_tf_init(dev, &tf); + + /* FIXME: is this needed? */ + memset(sense_buf, 0, SCSI_SENSE_BUFFERSIZE); + + /* XXX: why tf_read here? */ + ap->ops->tf_read(ap, &tf); + + /* fill these in, for the case where they are -not- overwritten */ + sense_buf[0] = 0x70; + sense_buf[2] = tf.feature >> 4; + + memset(cdb, 0, ATAPI_CDB_LEN); + cdb[0] = REQUEST_SENSE; + cdb[4] = SCSI_SENSE_BUFFERSIZE; + + tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + tf.command = ATA_CMD_PACKET; + + /* is it pointless to prefer PIO for "safety reasons"? */ + if (ap->flags & ATA_FLAG_PIO_DMA) { + tf.protocol = ATA_PROT_ATAPI_DMA; + tf.feature |= ATAPI_PKT_DMA; + } else { + tf.protocol = ATA_PROT_ATAPI; + tf.lbam = (8 * 1024) & 0xff; + tf.lbah = (8 * 1024) >> 8; + } + + return ata_exec_internal(dev, &tf, cdb, DMA_FROM_DEVICE, + sense_buf, SCSI_SENSE_BUFFERSIZE); +} + +/** + * ata_eh_analyze_serror - analyze SError for a failed port + * @ap: ATA port to analyze SError for + * + * Analyze SError if available and further determine cause of + * failure. + * + * LOCKING: + * None. + */ +static void ata_eh_analyze_serror(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + u32 serror = ehc->i.serror; + unsigned int err_mask = 0, action = 0; + + if (serror & SERR_PERSISTENT) { + err_mask |= AC_ERR_ATA_BUS; + action |= ATA_EH_HARDRESET; + } + if (serror & + (SERR_DATA_RECOVERED | SERR_COMM_RECOVERED | SERR_DATA)) { + err_mask |= AC_ERR_ATA_BUS; + action |= ATA_EH_SOFTRESET; + } + if (serror & SERR_PROTOCOL) { + err_mask |= AC_ERR_HSM; + action |= ATA_EH_SOFTRESET; + } + if (serror & SERR_INTERNAL) { + err_mask |= AC_ERR_SYSTEM; + action |= ATA_EH_SOFTRESET; + } + if (serror & (SERR_PHYRDY_CHG | SERR_DEV_XCHG)) + ata_ehi_hotplugged(&ehc->i); + + ehc->i.err_mask |= err_mask; + ehc->i.action |= action; +} + +/** + * ata_eh_analyze_ncq_error - analyze NCQ error + * @ap: ATA port to analyze NCQ error for + * + * Read log page 10h, determine the offending qc and acquire + * error status TF. For NCQ device errors, all LLDDs have to do + * is setting AC_ERR_DEV in ehi->err_mask. This function takes + * care of the rest. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +static void ata_eh_analyze_ncq_error(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + struct ata_device *dev = ap->device; + struct ata_queued_cmd *qc; + struct ata_taskfile tf; + int tag, rc; + + /* if frozen, we can't do much */ + if (ap->pflags & ATA_PFLAG_FROZEN) + return; + + /* is it NCQ device error? */ + if (!ap->sactive || !(ehc->i.err_mask & AC_ERR_DEV)) + return; + + /* has LLDD analyzed already? */ + for (tag = 0; tag < ATA_MAX_QUEUE; tag++) { + qc = __ata_qc_from_tag(ap, tag); + + if (!(qc->flags & ATA_QCFLAG_FAILED)) + continue; + + if (qc->err_mask) + return; + } + + /* okay, this error is ours */ + rc = ata_eh_read_log_10h(dev, &tag, &tf); + if (rc) { + ata_port_printk(ap, KERN_ERR, "failed to read log page 10h " + "(errno=%d)\n", rc); + return; + } + + if (!(ap->sactive & (1 << tag))) { + ata_port_printk(ap, KERN_ERR, "log page 10h reported " + "inactive tag %d\n", tag); + return; + } + + /* we've got the perpetrator, condemn it */ + qc = __ata_qc_from_tag(ap, tag); + memcpy(&qc->result_tf, &tf, sizeof(tf)); + qc->err_mask |= AC_ERR_DEV; + ehc->i.err_mask &= ~AC_ERR_DEV; +} + +/** + * ata_eh_analyze_tf - analyze taskfile of a failed qc + * @qc: qc to analyze + * @tf: Taskfile registers to analyze + * + * Analyze taskfile of @qc and further determine cause of + * failure. This function also requests ATAPI sense data if + * avaliable. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * Determined recovery action + */ +static unsigned int ata_eh_analyze_tf(struct ata_queued_cmd *qc, + const struct ata_taskfile *tf) +{ + unsigned int tmp, action = 0; + u8 stat = tf->command, err = tf->feature; + + if ((stat & (ATA_BUSY | ATA_DRQ | ATA_DRDY)) != ATA_DRDY) { + qc->err_mask |= AC_ERR_HSM; + return ATA_EH_SOFTRESET; + } + + if (!(qc->err_mask & AC_ERR_DEV)) + return 0; + + switch (qc->dev->class) { + case ATA_DEV_ATA: + if (err & ATA_ICRC) + qc->err_mask |= AC_ERR_ATA_BUS; + if (err & ATA_UNC) + qc->err_mask |= AC_ERR_MEDIA; + if (err & ATA_IDNF) + qc->err_mask |= AC_ERR_INVALID; + break; + + case ATA_DEV_ATAPI: + tmp = atapi_eh_request_sense(qc->dev, + qc->scsicmd->sense_buffer); + if (!tmp) { + /* ATA_QCFLAG_SENSE_VALID is used to tell + * atapi_qc_complete() that sense data is + * already valid. + * + * TODO: interpret sense data and set + * appropriate err_mask. + */ + qc->flags |= ATA_QCFLAG_SENSE_VALID; + } else + qc->err_mask |= tmp; + } + + if (qc->err_mask & (AC_ERR_HSM | AC_ERR_TIMEOUT | AC_ERR_ATA_BUS)) + action |= ATA_EH_SOFTRESET; + + return action; +} + +static int ata_eh_categorize_ering_entry(struct ata_ering_entry *ent) +{ + if (ent->err_mask & (AC_ERR_ATA_BUS | AC_ERR_TIMEOUT)) + return 1; + + if (ent->is_io) { + if (ent->err_mask & AC_ERR_HSM) + return 1; + if ((ent->err_mask & + (AC_ERR_DEV|AC_ERR_MEDIA|AC_ERR_INVALID)) == AC_ERR_DEV) + return 2; + } + + return 0; +} + +struct speed_down_needed_arg { + u64 since; + int nr_errors[3]; +}; + +static int speed_down_needed_cb(struct ata_ering_entry *ent, void *void_arg) +{ + struct speed_down_needed_arg *arg = void_arg; + + if (ent->timestamp < arg->since) + return -1; + + arg->nr_errors[ata_eh_categorize_ering_entry(ent)]++; + return 0; +} + +/** + * ata_eh_speed_down_needed - Determine wheter speed down is necessary + * @dev: Device of interest + * + * This function examines error ring of @dev and determines + * whether speed down is necessary. Speed down is necessary if + * there have been more than 3 of Cat-1 errors or 10 of Cat-2 + * errors during last 15 minutes. + * + * Cat-1 errors are ATA_BUS, TIMEOUT for any command and HSM + * violation for known supported commands. + * + * Cat-2 errors are unclassified DEV error for known supported + * command. + * + * LOCKING: + * Inherited from caller. + * + * RETURNS: + * 1 if speed down is necessary, 0 otherwise + */ +static int ata_eh_speed_down_needed(struct ata_device *dev) +{ + const u64 interval = 15LLU * 60 * HZ; + static const int err_limits[3] = { -1, 3, 10 }; + struct speed_down_needed_arg arg; + struct ata_ering_entry *ent; + int err_cat; + u64 j64; + + ent = ata_ering_top(&dev->ering); + if (!ent) + return 0; + + err_cat = ata_eh_categorize_ering_entry(ent); + if (err_cat == 0) + return 0; + + memset(&arg, 0, sizeof(arg)); + + j64 = get_jiffies_64(); + if (j64 >= interval) + arg.since = j64 - interval; + else + arg.since = 0; + + ata_ering_map(&dev->ering, speed_down_needed_cb, &arg); + + return arg.nr_errors[err_cat] > err_limits[err_cat]; +} + +/** + * ata_eh_speed_down - record error and speed down if necessary + * @dev: Failed device + * @is_io: Did the device fail during normal IO? + * @err_mask: err_mask of the error + * + * Record error and examine error history to determine whether + * adjusting transmission speed is necessary. It also sets + * transmission limits appropriately if such adjustment is + * necessary. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno otherwise + */ +static int ata_eh_speed_down(struct ata_device *dev, int is_io, + unsigned int err_mask) +{ + if (!err_mask) + return 0; + + /* record error and determine whether speed down is necessary */ + ata_ering_record(&dev->ering, is_io, err_mask); + + if (!ata_eh_speed_down_needed(dev)) + return 0; + + /* speed down SATA link speed if possible */ + if (sata_down_spd_limit(dev->ap) == 0) + return ATA_EH_HARDRESET; + + /* lower transfer mode */ + if (ata_down_xfermask_limit(dev, 0) == 0) + return ATA_EH_SOFTRESET; + + ata_dev_printk(dev, KERN_ERR, + "speed down requested but no transfer mode left\n"); + return 0; +} + +/** + * ata_eh_autopsy - analyze error and determine recovery action + * @ap: ATA port to perform autopsy on + * + * Analyze why @ap failed and determine which recovery action is + * needed. This function also sets more detailed AC_ERR_* values + * and fills sense data for ATAPI CHECK SENSE. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +static void ata_eh_autopsy(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + unsigned int all_err_mask = 0; + int tag, is_io = 0; + u32 serror; + int rc; + + DPRINTK("ENTER\n"); + + if (ehc->i.flags & ATA_EHI_NO_AUTOPSY) + return; + + /* obtain and analyze SError */ + rc = sata_scr_read(ap, SCR_ERROR, &serror); + if (rc == 0) { + ehc->i.serror |= serror; + ata_eh_analyze_serror(ap); + } else if (rc != -EOPNOTSUPP) + ehc->i.action |= ATA_EH_HARDRESET; + + /* analyze NCQ failure */ + ata_eh_analyze_ncq_error(ap); + + /* any real error trumps AC_ERR_OTHER */ + if (ehc->i.err_mask & ~AC_ERR_OTHER) + ehc->i.err_mask &= ~AC_ERR_OTHER; + + all_err_mask |= ehc->i.err_mask; + + for (tag = 0; tag < ATA_MAX_QUEUE; tag++) { + struct ata_queued_cmd *qc = __ata_qc_from_tag(ap, tag); + + if (!(qc->flags & ATA_QCFLAG_FAILED)) + continue; + + /* inherit upper level err_mask */ + qc->err_mask |= ehc->i.err_mask; + + /* analyze TF */ + ehc->i.action |= ata_eh_analyze_tf(qc, &qc->result_tf); + + /* DEV errors are probably spurious in case of ATA_BUS error */ + if (qc->err_mask & AC_ERR_ATA_BUS) + qc->err_mask &= ~(AC_ERR_DEV | AC_ERR_MEDIA | + AC_ERR_INVALID); + + /* any real error trumps unknown error */ + if (qc->err_mask & ~AC_ERR_OTHER) + qc->err_mask &= ~AC_ERR_OTHER; + + /* SENSE_VALID trumps dev/unknown error and revalidation */ + if (qc->flags & ATA_QCFLAG_SENSE_VALID) { + qc->err_mask &= ~(AC_ERR_DEV | AC_ERR_OTHER); + ehc->i.action &= ~ATA_EH_REVALIDATE; + } + + /* accumulate error info */ + ehc->i.dev = qc->dev; + all_err_mask |= qc->err_mask; + if (qc->flags & ATA_QCFLAG_IO) + is_io = 1; + } + + /* enforce default EH actions */ + if (ap->pflags & ATA_PFLAG_FROZEN || + all_err_mask & (AC_ERR_HSM | AC_ERR_TIMEOUT)) + ehc->i.action |= ATA_EH_SOFTRESET; + else if (all_err_mask) + ehc->i.action |= ATA_EH_REVALIDATE; + + /* if we have offending qcs and the associated failed device */ + if (ehc->i.dev) { + /* speed down */ + ehc->i.action |= ata_eh_speed_down(ehc->i.dev, is_io, + all_err_mask); + + /* perform per-dev EH action only on the offending device */ + ehc->i.dev_action[ehc->i.dev->devno] |= + ehc->i.action & ATA_EH_PERDEV_MASK; + ehc->i.action &= ~ATA_EH_PERDEV_MASK; + } + + DPRINTK("EXIT\n"); +} + +/** + * ata_eh_report - report error handling to user + * @ap: ATA port EH is going on + * + * Report EH to user. + * + * LOCKING: + * None. + */ +static void ata_eh_report(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + const char *frozen, *desc; + int tag, nr_failed = 0; + + desc = NULL; + if (ehc->i.desc[0] != '\0') + desc = ehc->i.desc; + + for (tag = 0; tag < ATA_MAX_QUEUE; tag++) { + struct ata_queued_cmd *qc = __ata_qc_from_tag(ap, tag); + + if (!(qc->flags & ATA_QCFLAG_FAILED)) + continue; + if (qc->flags & ATA_QCFLAG_SENSE_VALID && !qc->err_mask) + continue; + + nr_failed++; + } + + if (!nr_failed && !ehc->i.err_mask) + return; + + frozen = ""; + if (ap->pflags & ATA_PFLAG_FROZEN) + frozen = " frozen"; + + if (ehc->i.dev) { + ata_dev_printk(ehc->i.dev, KERN_ERR, "exception Emask 0x%x " + "SAct 0x%x SErr 0x%x action 0x%x%s\n", + ehc->i.err_mask, ap->sactive, ehc->i.serror, + ehc->i.action, frozen); + if (desc) + ata_dev_printk(ehc->i.dev, KERN_ERR, "(%s)\n", desc); + } else { + ata_port_printk(ap, KERN_ERR, "exception Emask 0x%x " + "SAct 0x%x SErr 0x%x action 0x%x%s\n", + ehc->i.err_mask, ap->sactive, ehc->i.serror, + ehc->i.action, frozen); + if (desc) + ata_port_printk(ap, KERN_ERR, "(%s)\n", desc); + } + + for (tag = 0; tag < ATA_MAX_QUEUE; tag++) { + struct ata_queued_cmd *qc = __ata_qc_from_tag(ap, tag); + + if (!(qc->flags & ATA_QCFLAG_FAILED) || !qc->err_mask) + continue; + + ata_dev_printk(qc->dev, KERN_ERR, "tag %d cmd 0x%x " + "Emask 0x%x stat 0x%x err 0x%x (%s)\n", + qc->tag, qc->tf.command, qc->err_mask, + qc->result_tf.command, qc->result_tf.feature, + ata_err_string(qc->err_mask)); + } +} + +static int ata_do_reset(struct ata_port *ap, ata_reset_fn_t reset, + unsigned int *classes) +{ + int i, rc; + + for (i = 0; i < ATA_MAX_DEVICES; i++) + classes[i] = ATA_DEV_UNKNOWN; + + rc = reset(ap, classes); + if (rc) + return rc; + + /* If any class isn't ATA_DEV_UNKNOWN, consider classification + * is complete and convert all ATA_DEV_UNKNOWN to + * ATA_DEV_NONE. + */ + for (i = 0; i < ATA_MAX_DEVICES; i++) + if (classes[i] != ATA_DEV_UNKNOWN) + break; + + if (i < ATA_MAX_DEVICES) + for (i = 0; i < ATA_MAX_DEVICES; i++) + if (classes[i] == ATA_DEV_UNKNOWN) + classes[i] = ATA_DEV_NONE; + + return 0; +} + +static int ata_eh_followup_srst_needed(int rc, int classify, + const unsigned int *classes) +{ + if (rc == -EAGAIN) + return 1; + if (rc != 0) + return 0; + if (classify && classes[0] == ATA_DEV_UNKNOWN) + return 1; + return 0; +} + +static int ata_eh_reset(struct ata_port *ap, int classify, + ata_prereset_fn_t prereset, ata_reset_fn_t softreset, + ata_reset_fn_t hardreset, ata_postreset_fn_t postreset) +{ + struct ata_eh_context *ehc = &ap->eh_context; + unsigned int *classes = ehc->classes; + int tries = ATA_EH_RESET_TRIES; + int verbose = !(ehc->i.flags & ATA_EHI_QUIET); + unsigned int action; + ata_reset_fn_t reset; + int i, did_followup_srst, rc; + + /* about to reset */ + ata_eh_about_to_do(ap, NULL, ehc->i.action & ATA_EH_RESET_MASK); + + /* Determine which reset to use and record in ehc->i.action. + * prereset() may examine and modify it. + */ + action = ehc->i.action; + ehc->i.action &= ~ATA_EH_RESET_MASK; + if (softreset && (!hardreset || (!sata_set_spd_needed(ap) && + !(action & ATA_EH_HARDRESET)))) + ehc->i.action |= ATA_EH_SOFTRESET; + else + ehc->i.action |= ATA_EH_HARDRESET; + + if (prereset) { + rc = prereset(ap); + if (rc) { + if (rc == -ENOENT) { + ata_port_printk(ap, KERN_DEBUG, "port disabled. ignoring.\n"); + ap->eh_context.i.action &= ~ATA_EH_RESET_MASK; + } else + ata_port_printk(ap, KERN_ERR, + "prereset failed (errno=%d)\n", rc); + return rc; + } + } + + /* prereset() might have modified ehc->i.action */ + if (ehc->i.action & ATA_EH_HARDRESET) + reset = hardreset; + else if (ehc->i.action & ATA_EH_SOFTRESET) + reset = softreset; + else { + /* prereset told us not to reset, bang classes and return */ + for (i = 0; i < ATA_MAX_DEVICES; i++) + classes[i] = ATA_DEV_NONE; + return 0; + } + + /* did prereset() screw up? if so, fix up to avoid oopsing */ + if (!reset) { + ata_port_printk(ap, KERN_ERR, "BUG: prereset() requested " + "invalid reset type\n"); + if (softreset) + reset = softreset; + else + reset = hardreset; + } + + retry: + /* shut up during boot probing */ + if (verbose) + ata_port_printk(ap, KERN_INFO, "%s resetting port\n", + reset == softreset ? "soft" : "hard"); + + /* mark that this EH session started with reset */ + ehc->i.flags |= ATA_EHI_DID_RESET; + + rc = ata_do_reset(ap, reset, classes); + + did_followup_srst = 0; + if (reset == hardreset && + ata_eh_followup_srst_needed(rc, classify, classes)) { + /* okay, let's do follow-up softreset */ + did_followup_srst = 1; + reset = softreset; + + if (!reset) { + ata_port_printk(ap, KERN_ERR, + "follow-up softreset required " + "but no softreset avaliable\n"); + return -EINVAL; + } + + ata_eh_about_to_do(ap, NULL, ATA_EH_RESET_MASK); + rc = ata_do_reset(ap, reset, classes); + + if (rc == 0 && classify && + classes[0] == ATA_DEV_UNKNOWN) { + ata_port_printk(ap, KERN_ERR, + "classification failed\n"); + return -EINVAL; + } + } + + if (rc && --tries) { + const char *type; + + if (reset == softreset) { + if (did_followup_srst) + type = "follow-up soft"; + else + type = "soft"; + } else + type = "hard"; + + ata_port_printk(ap, KERN_WARNING, + "%sreset failed, retrying in 5 secs\n", type); + ssleep(5); + + if (reset == hardreset) + sata_down_spd_limit(ap); + if (hardreset) + reset = hardreset; + goto retry; + } + + if (rc == 0) { + /* After the reset, the device state is PIO 0 and the + * controller state is undefined. Record the mode. + */ + for (i = 0; i < ATA_MAX_DEVICES; i++) + ap->device[i].pio_mode = XFER_PIO_0; + + if (postreset) + postreset(ap, classes); + + /* reset successful, schedule revalidation */ + ata_eh_done(ap, NULL, ehc->i.action & ATA_EH_RESET_MASK); + ehc->i.action |= ATA_EH_REVALIDATE; + } + + return rc; +} + +static int ata_eh_revalidate_and_attach(struct ata_port *ap, + struct ata_device **r_failed_dev) +{ + struct ata_eh_context *ehc = &ap->eh_context; + struct ata_device *dev; + unsigned long flags; + int i, rc = 0; + + DPRINTK("ENTER\n"); + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + unsigned int action; + + dev = &ap->device[i]; + action = ata_eh_dev_action(dev); + + if (action & ATA_EH_REVALIDATE && ata_dev_ready(dev)) { + if (ata_port_offline(ap)) { + rc = -EIO; + break; + } + + ata_eh_about_to_do(ap, dev, ATA_EH_REVALIDATE); + rc = ata_dev_revalidate(dev, + ehc->i.flags & ATA_EHI_DID_RESET); + if (rc) + break; + + ata_eh_done(ap, dev, ATA_EH_REVALIDATE); + + /* schedule the scsi_rescan_device() here */ + queue_work(ata_aux_wq, &(ap->scsi_rescan_task)); + } else if (dev->class == ATA_DEV_UNKNOWN && + ehc->tries[dev->devno] && + ata_class_enabled(ehc->classes[dev->devno])) { + dev->class = ehc->classes[dev->devno]; + + rc = ata_dev_read_id(dev, &dev->class, 1, dev->id); + if (rc == 0) + rc = ata_dev_configure(dev, 1); + + if (rc) { + dev->class = ATA_DEV_UNKNOWN; + break; + } + + spin_lock_irqsave(ap->lock, flags); + ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG; + spin_unlock_irqrestore(ap->lock, flags); + } + } + + if (rc) + *r_failed_dev = dev; + + DPRINTK("EXIT\n"); + return rc; +} + +/** + * ata_eh_suspend - handle suspend EH action + * @ap: target host port + * @r_failed_dev: result parameter to indicate failing device + * + * Handle suspend EH action. Disk devices are spinned down and + * other types of devices are just marked suspended. Once + * suspended, no EH action to the device is allowed until it is + * resumed. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno otherwise + */ +static int ata_eh_suspend(struct ata_port *ap, struct ata_device **r_failed_dev) +{ + struct ata_device *dev; + int i, rc = 0; + + DPRINTK("ENTER\n"); + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + unsigned long flags; + unsigned int action, err_mask; + + dev = &ap->device[i]; + action = ata_eh_dev_action(dev); + + if (!ata_dev_enabled(dev) || !(action & ATA_EH_SUSPEND)) + continue; + + WARN_ON(dev->flags & ATA_DFLAG_SUSPENDED); + + ata_eh_about_to_do(ap, dev, ATA_EH_SUSPEND); + + if (dev->class == ATA_DEV_ATA && !(action & ATA_EH_PM_FREEZE)) { + /* flush cache */ + rc = ata_flush_cache(dev); + if (rc) + break; + + /* spin down */ + err_mask = ata_do_simple_cmd(dev, ATA_CMD_STANDBYNOW1); + if (err_mask) { + ata_dev_printk(dev, KERN_ERR, "failed to " + "spin down (err_mask=0x%x)\n", + err_mask); + rc = -EIO; + break; + } + } + + spin_lock_irqsave(ap->lock, flags); + dev->flags |= ATA_DFLAG_SUSPENDED; + spin_unlock_irqrestore(ap->lock, flags); + + ata_eh_done(ap, dev, ATA_EH_SUSPEND); + } + + if (rc) + *r_failed_dev = dev; + + DPRINTK("EXIT\n"); + return 0; +} + +/** + * ata_eh_prep_resume - prep for resume EH action + * @ap: target host port + * + * Clear SUSPENDED in preparation for scheduled resume actions. + * This allows other parts of EH to access the devices being + * resumed. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +static void ata_eh_prep_resume(struct ata_port *ap) +{ + struct ata_device *dev; + unsigned long flags; + int i; + + DPRINTK("ENTER\n"); + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + unsigned int action; + + dev = &ap->device[i]; + action = ata_eh_dev_action(dev); + + if (!ata_dev_enabled(dev) || !(action & ATA_EH_RESUME)) + continue; + + spin_lock_irqsave(ap->lock, flags); + dev->flags &= ~ATA_DFLAG_SUSPENDED; + spin_unlock_irqrestore(ap->lock, flags); + } + + DPRINTK("EXIT\n"); +} + +/** + * ata_eh_resume - handle resume EH action + * @ap: target host port + * @r_failed_dev: result parameter to indicate failing device + * + * Handle resume EH action. Target devices are already reset and + * revalidated. Spinning up is the only operation left. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno otherwise + */ +static int ata_eh_resume(struct ata_port *ap, struct ata_device **r_failed_dev) +{ + struct ata_device *dev; + int i, rc = 0; + + DPRINTK("ENTER\n"); + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + unsigned int action, err_mask; + + dev = &ap->device[i]; + action = ata_eh_dev_action(dev); + + if (!ata_dev_enabled(dev) || !(action & ATA_EH_RESUME)) + continue; + + ata_eh_about_to_do(ap, dev, ATA_EH_RESUME); + + if (dev->class == ATA_DEV_ATA && !(action & ATA_EH_PM_FREEZE)) { + err_mask = ata_do_simple_cmd(dev, + ATA_CMD_IDLEIMMEDIATE); + if (err_mask) { + ata_dev_printk(dev, KERN_ERR, "failed to " + "spin up (err_mask=0x%x)\n", + err_mask); + rc = -EIO; + break; + } + } + + ata_eh_done(ap, dev, ATA_EH_RESUME); + } + + if (rc) + *r_failed_dev = dev; + + DPRINTK("EXIT\n"); + return 0; +} + +static int ata_port_nr_enabled(struct ata_port *ap) +{ + int i, cnt = 0; + + for (i = 0; i < ATA_MAX_DEVICES; i++) + if (ata_dev_enabled(&ap->device[i])) + cnt++; + return cnt; +} + +static int ata_port_nr_vacant(struct ata_port *ap) +{ + int i, cnt = 0; + + for (i = 0; i < ATA_MAX_DEVICES; i++) + if (ap->device[i].class == ATA_DEV_UNKNOWN) + cnt++; + return cnt; +} + +static int ata_eh_skip_recovery(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + int i; + + /* skip if all possible devices are suspended */ + for (i = 0; i < ata_port_max_devices(ap); i++) { + struct ata_device *dev = &ap->device[i]; + + if (!(dev->flags & ATA_DFLAG_SUSPENDED)) + break; + } + + if (i == ata_port_max_devices(ap)) + return 1; + + /* thaw frozen port, resume link and recover failed devices */ + if ((ap->pflags & ATA_PFLAG_FROZEN) || + (ehc->i.flags & ATA_EHI_RESUME_LINK) || ata_port_nr_enabled(ap)) + return 0; + + /* skip if class codes for all vacant slots are ATA_DEV_NONE */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + + if (dev->class == ATA_DEV_UNKNOWN && + ehc->classes[dev->devno] != ATA_DEV_NONE) + return 0; + } + + return 1; +} + +/** + * ata_eh_recover - recover host port after error + * @ap: host port to recover + * @prereset: prereset method (can be NULL) + * @softreset: softreset method (can be NULL) + * @hardreset: hardreset method (can be NULL) + * @postreset: postreset method (can be NULL) + * + * This is the alpha and omega, eum and yang, heart and soul of + * libata exception handling. On entry, actions required to + * recover the port and hotplug requests are recorded in + * eh_context. This function executes all the operations with + * appropriate retrials and fallbacks to resurrect failed + * devices, detach goners and greet newcomers. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno on failure. + */ +static int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset, + ata_reset_fn_t softreset, ata_reset_fn_t hardreset, + ata_postreset_fn_t postreset) +{ + struct ata_eh_context *ehc = &ap->eh_context; + struct ata_device *dev; + int down_xfermask, i, rc; + + DPRINTK("ENTER\n"); + + /* prep for recovery */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + dev = &ap->device[i]; + + ehc->tries[dev->devno] = ATA_EH_DEV_TRIES; + + /* process hotplug request */ + if (dev->flags & ATA_DFLAG_DETACH) + ata_eh_detach_dev(dev); + + if (!ata_dev_enabled(dev) && + ((ehc->i.probe_mask & (1 << dev->devno)) && + !(ehc->did_probe_mask & (1 << dev->devno)))) { + ata_eh_detach_dev(dev); + ata_dev_init(dev); + ehc->did_probe_mask |= (1 << dev->devno); + ehc->i.action |= ATA_EH_SOFTRESET; + } + } + + retry: + down_xfermask = 0; + rc = 0; + + /* if UNLOADING, finish immediately */ + if (ap->pflags & ATA_PFLAG_UNLOADING) + goto out; + + /* prep for resume */ + ata_eh_prep_resume(ap); + + /* skip EH if possible. */ + if (ata_eh_skip_recovery(ap)) + ehc->i.action = 0; + + for (i = 0; i < ATA_MAX_DEVICES; i++) + ehc->classes[i] = ATA_DEV_UNKNOWN; + + /* reset */ + if (ehc->i.action & ATA_EH_RESET_MASK) { + ata_eh_freeze_port(ap); + + rc = ata_eh_reset(ap, ata_port_nr_vacant(ap), prereset, + softreset, hardreset, postreset); + if (rc) { + ata_port_printk(ap, KERN_ERR, + "reset failed, giving up\n"); + goto out; + } + + ata_eh_thaw_port(ap); + } + + /* revalidate existing devices and attach new ones */ + rc = ata_eh_revalidate_and_attach(ap, &dev); + if (rc) + goto dev_fail; + + /* resume devices */ + rc = ata_eh_resume(ap, &dev); + if (rc) + goto dev_fail; + + /* configure transfer mode if the port has been reset */ + if (ehc->i.flags & ATA_EHI_DID_RESET) { + rc = ata_set_mode(ap, &dev); + if (rc) { + down_xfermask = 1; + goto dev_fail; + } + } + + /* suspend devices */ + rc = ata_eh_suspend(ap, &dev); + if (rc) + goto dev_fail; + + goto out; + + dev_fail: + switch (rc) { + case -ENODEV: + /* device missing, schedule probing */ + ehc->i.probe_mask |= (1 << dev->devno); + case -EINVAL: + ehc->tries[dev->devno] = 0; + break; + case -EIO: + sata_down_spd_limit(ap); + default: + ehc->tries[dev->devno]--; + if (down_xfermask && + ata_down_xfermask_limit(dev, ehc->tries[dev->devno] == 1)) + ehc->tries[dev->devno] = 0; + } + + if (ata_dev_enabled(dev) && !ehc->tries[dev->devno]) { + /* disable device if it has used up all its chances */ + ata_dev_disable(dev); + + /* detach if offline */ + if (ata_port_offline(ap)) + ata_eh_detach_dev(dev); + + /* probe if requested */ + if ((ehc->i.probe_mask & (1 << dev->devno)) && + !(ehc->did_probe_mask & (1 << dev->devno))) { + ata_eh_detach_dev(dev); + ata_dev_init(dev); + + ehc->tries[dev->devno] = ATA_EH_DEV_TRIES; + ehc->did_probe_mask |= (1 << dev->devno); + ehc->i.action |= ATA_EH_SOFTRESET; + } + } else { + /* soft didn't work? be haaaaard */ + if (ehc->i.flags & ATA_EHI_DID_RESET) + ehc->i.action |= ATA_EH_HARDRESET; + else + ehc->i.action |= ATA_EH_SOFTRESET; + } + + if (ata_port_nr_enabled(ap)) { + ata_port_printk(ap, KERN_WARNING, "failed to recover some " + "devices, retrying in 5 secs\n"); + ssleep(5); + } else { + /* no device left, repeat fast */ + msleep(500); + } + + goto retry; + + out: + if (rc) { + for (i = 0; i < ATA_MAX_DEVICES; i++) + ata_dev_disable(&ap->device[i]); + } + + DPRINTK("EXIT, rc=%d\n", rc); + return rc; +} + +/** + * ata_eh_finish - finish up EH + * @ap: host port to finish EH for + * + * Recovery is complete. Clean up EH states and retry or finish + * failed qcs. + * + * LOCKING: + * None. + */ +static void ata_eh_finish(struct ata_port *ap) +{ + int tag; + + /* retry or finish qcs */ + for (tag = 0; tag < ATA_MAX_QUEUE; tag++) { + struct ata_queued_cmd *qc = __ata_qc_from_tag(ap, tag); + + if (!(qc->flags & ATA_QCFLAG_FAILED)) + continue; + + if (qc->err_mask) { + /* FIXME: Once EH migration is complete, + * generate sense data in this function, + * considering both err_mask and tf. + */ + if (qc->err_mask & AC_ERR_INVALID) + ata_eh_qc_complete(qc); + else + ata_eh_qc_retry(qc); + } else { + if (qc->flags & ATA_QCFLAG_SENSE_VALID) { + ata_eh_qc_complete(qc); + } else { + /* feed zero TF to sense generation */ + memset(&qc->result_tf, 0, sizeof(qc->result_tf)); + ata_eh_qc_retry(qc); + } + } + } +} + +/** + * ata_do_eh - do standard error handling + * @ap: host port to handle error for + * @prereset: prereset method (can be NULL) + * @softreset: softreset method (can be NULL) + * @hardreset: hardreset method (can be NULL) + * @postreset: postreset method (can be NULL) + * + * Perform standard error handling sequence. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset, + ata_reset_fn_t softreset, ata_reset_fn_t hardreset, + ata_postreset_fn_t postreset) +{ + ata_eh_autopsy(ap); + ata_eh_report(ap); + ata_eh_recover(ap, prereset, softreset, hardreset, postreset); + ata_eh_finish(ap); +} + +/** + * ata_eh_handle_port_suspend - perform port suspend operation + * @ap: port to suspend + * + * Suspend @ap. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +static void ata_eh_handle_port_suspend(struct ata_port *ap) +{ + unsigned long flags; + int rc = 0; + + /* are we suspending? */ + spin_lock_irqsave(ap->lock, flags); + if (!(ap->pflags & ATA_PFLAG_PM_PENDING) || + ap->pm_mesg.event == PM_EVENT_ON) { + spin_unlock_irqrestore(ap->lock, flags); + return; + } + spin_unlock_irqrestore(ap->lock, flags); + + WARN_ON(ap->pflags & ATA_PFLAG_SUSPENDED); + + /* suspend */ + ata_eh_freeze_port(ap); + + if (ap->ops->port_suspend) + rc = ap->ops->port_suspend(ap, ap->pm_mesg); + + /* report result */ + spin_lock_irqsave(ap->lock, flags); + + ap->pflags &= ~ATA_PFLAG_PM_PENDING; + if (rc == 0) + ap->pflags |= ATA_PFLAG_SUSPENDED; + else + ata_port_schedule_eh(ap); + + if (ap->pm_result) { + *ap->pm_result = rc; + ap->pm_result = NULL; + } + + spin_unlock_irqrestore(ap->lock, flags); + + return; +} + +/** + * ata_eh_handle_port_resume - perform port resume operation + * @ap: port to resume + * + * Resume @ap. + * + * This function also waits upto one second until all devices + * hanging off this port requests resume EH action. This is to + * prevent invoking EH and thus reset multiple times on resume. + * + * On DPM resume, where some of devices might not be resumed + * together, this may delay port resume upto one second, but such + * DPM resumes are rare and 1 sec delay isn't too bad. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +static void ata_eh_handle_port_resume(struct ata_port *ap) +{ + unsigned long timeout; + unsigned long flags; + int i, rc = 0; + + /* are we resuming? */ + spin_lock_irqsave(ap->lock, flags); + if (!(ap->pflags & ATA_PFLAG_PM_PENDING) || + ap->pm_mesg.event != PM_EVENT_ON) { + spin_unlock_irqrestore(ap->lock, flags); + return; + } + spin_unlock_irqrestore(ap->lock, flags); + + /* spurious? */ + if (!(ap->pflags & ATA_PFLAG_SUSPENDED)) + goto done; + + if (ap->ops->port_resume) + rc = ap->ops->port_resume(ap); + + /* give devices time to request EH */ + timeout = jiffies + HZ; /* 1s max */ + while (1) { + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + unsigned int action = ata_eh_dev_action(dev); + + if ((dev->flags & ATA_DFLAG_SUSPENDED) && + !(action & ATA_EH_RESUME)) + break; + } + + if (i == ATA_MAX_DEVICES || time_after(jiffies, timeout)) + break; + msleep(10); + } + + done: + spin_lock_irqsave(ap->lock, flags); + ap->pflags &= ~(ATA_PFLAG_PM_PENDING | ATA_PFLAG_SUSPENDED); + if (ap->pm_result) { + *ap->pm_result = rc; + ap->pm_result = NULL; + } + spin_unlock_irqrestore(ap->lock, flags); +} diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c new file mode 100644 index 00000000000..3986ec8741b --- /dev/null +++ b/drivers/ata/libata-scsi.c @@ -0,0 +1,3322 @@ +/* + * libata-scsi.c - helper library for ATA + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2003-2004 Red Hat, Inc. All rights reserved. + * Copyright 2003-2004 Jeff Garzik + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available from + * - http://www.t10.org/ + * - http://www.t13.org/ + * + */ + +#include <linux/kernel.h> +#include <linux/blkdev.h> +#include <linux/spinlock.h> +#include <scsi/scsi.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <scsi/scsi_eh.h> +#include <scsi/scsi_device.h> +#include <scsi/scsi_tcq.h> +#include <scsi/scsi_transport.h> +#include <linux/libata.h> +#include <linux/hdreg.h> +#include <asm/uaccess.h> + +#include "libata.h" + +#define SECTOR_SIZE 512 + +typedef unsigned int (*ata_xlat_func_t)(struct ata_queued_cmd *qc, const u8 *scsicmd); + +static struct ata_device * __ata_scsi_find_dev(struct ata_port *ap, + const struct scsi_device *scsidev); +static struct ata_device * ata_scsi_find_dev(struct ata_port *ap, + const struct scsi_device *scsidev); +static int ata_scsi_user_scan(struct Scsi_Host *shost, unsigned int channel, + unsigned int id, unsigned int lun); + + +#define RW_RECOVERY_MPAGE 0x1 +#define RW_RECOVERY_MPAGE_LEN 12 +#define CACHE_MPAGE 0x8 +#define CACHE_MPAGE_LEN 20 +#define CONTROL_MPAGE 0xa +#define CONTROL_MPAGE_LEN 12 +#define ALL_MPAGES 0x3f +#define ALL_SUB_MPAGES 0xff + + +static const u8 def_rw_recovery_mpage[] = { + RW_RECOVERY_MPAGE, + RW_RECOVERY_MPAGE_LEN - 2, + (1 << 7) | /* AWRE, sat-r06 say it shall be 0 */ + (1 << 6), /* ARRE (auto read reallocation) */ + 0, /* read retry count */ + 0, 0, 0, 0, + 0, /* write retry count */ + 0, 0, 0 +}; + +static const u8 def_cache_mpage[CACHE_MPAGE_LEN] = { + CACHE_MPAGE, + CACHE_MPAGE_LEN - 2, + 0, /* contains WCE, needs to be 0 for logic */ + 0, 0, 0, 0, 0, 0, 0, 0, 0, + 0, /* contains DRA, needs to be 0 for logic */ + 0, 0, 0, 0, 0, 0, 0 +}; + +static const u8 def_control_mpage[CONTROL_MPAGE_LEN] = { + CONTROL_MPAGE, + CONTROL_MPAGE_LEN - 2, + 2, /* DSENSE=0, GLTSD=1 */ + 0, /* [QAM+QERR may be 1, see 05-359r1] */ + 0, 0, 0, 0, 0xff, 0xff, + 0, 30 /* extended self test time, see 05-359r1 */ +}; + +/* + * libata transport template. libata doesn't do real transport stuff. + * It just needs the eh_timed_out hook. + */ +struct scsi_transport_template ata_scsi_transport_template = { + .eh_strategy_handler = ata_scsi_error, + .eh_timed_out = ata_scsi_timed_out, + .user_scan = ata_scsi_user_scan, +}; + + +static void ata_scsi_invalid_field(struct scsi_cmnd *cmd, + void (*done)(struct scsi_cmnd *)) +{ + ata_scsi_set_sense(cmd, ILLEGAL_REQUEST, 0x24, 0x0); + /* "Invalid field in cbd" */ + done(cmd); +} + +/** + * ata_std_bios_param - generic bios head/sector/cylinder calculator used by sd. + * @sdev: SCSI device for which BIOS geometry is to be determined + * @bdev: block device associated with @sdev + * @capacity: capacity of SCSI device + * @geom: location to which geometry will be output + * + * Generic bios head/sector/cylinder calculator + * used by sd. Most BIOSes nowadays expect a XXX/255/16 (CHS) + * mapping. Some situations may arise where the disk is not + * bootable if this is not used. + * + * LOCKING: + * Defined by the SCSI layer. We don't really care. + * + * RETURNS: + * Zero. + */ +int ata_std_bios_param(struct scsi_device *sdev, struct block_device *bdev, + sector_t capacity, int geom[]) +{ + geom[0] = 255; + geom[1] = 63; + sector_div(capacity, 255*63); + geom[2] = capacity; + + return 0; +} + +/** + * ata_cmd_ioctl - Handler for HDIO_DRIVE_CMD ioctl + * @scsidev: Device to which we are issuing command + * @arg: User provided data for issuing command + * + * LOCKING: + * Defined by the SCSI layer. We don't really care. + * + * RETURNS: + * Zero on success, negative errno on error. + */ + +int ata_cmd_ioctl(struct scsi_device *scsidev, void __user *arg) +{ + int rc = 0; + u8 scsi_cmd[MAX_COMMAND_SIZE]; + u8 args[4], *argbuf = NULL; + int argsize = 0; + struct scsi_sense_hdr sshdr; + enum dma_data_direction data_dir; + + if (arg == NULL) + return -EINVAL; + + if (copy_from_user(args, arg, sizeof(args))) + return -EFAULT; + + memset(scsi_cmd, 0, sizeof(scsi_cmd)); + + if (args[3]) { + argsize = SECTOR_SIZE * args[3]; + argbuf = kmalloc(argsize, GFP_KERNEL); + if (argbuf == NULL) { + rc = -ENOMEM; + goto error; + } + + scsi_cmd[1] = (4 << 1); /* PIO Data-in */ + scsi_cmd[2] = 0x0e; /* no off.line or cc, read from dev, + block count in sector count field */ + data_dir = DMA_FROM_DEVICE; + } else { + scsi_cmd[1] = (3 << 1); /* Non-data */ + /* scsi_cmd[2] is already 0 -- no off.line, cc, or data xfer */ + data_dir = DMA_NONE; + } + + scsi_cmd[0] = ATA_16; + + scsi_cmd[4] = args[2]; + if (args[0] == WIN_SMART) { /* hack -- ide driver does this too... */ + scsi_cmd[6] = args[3]; + scsi_cmd[8] = args[1]; + scsi_cmd[10] = 0x4f; + scsi_cmd[12] = 0xc2; + } else { + scsi_cmd[6] = args[1]; + } + scsi_cmd[14] = args[0]; + + /* Good values for timeout and retries? Values below + from scsi_ioctl_send_command() for default case... */ + if (scsi_execute_req(scsidev, scsi_cmd, data_dir, argbuf, argsize, + &sshdr, (10*HZ), 5)) { + rc = -EIO; + goto error; + } + + /* Need code to retrieve data from check condition? */ + + if ((argbuf) + && copy_to_user(arg + sizeof(args), argbuf, argsize)) + rc = -EFAULT; +error: + kfree(argbuf); + return rc; +} + +/** + * ata_task_ioctl - Handler for HDIO_DRIVE_TASK ioctl + * @scsidev: Device to which we are issuing command + * @arg: User provided data for issuing command + * + * LOCKING: + * Defined by the SCSI layer. We don't really care. + * + * RETURNS: + * Zero on success, negative errno on error. + */ +int ata_task_ioctl(struct scsi_device *scsidev, void __user *arg) +{ + int rc = 0; + u8 scsi_cmd[MAX_COMMAND_SIZE]; + u8 args[7]; + struct scsi_sense_hdr sshdr; + + if (arg == NULL) + return -EINVAL; + + if (copy_from_user(args, arg, sizeof(args))) + return -EFAULT; + + memset(scsi_cmd, 0, sizeof(scsi_cmd)); + scsi_cmd[0] = ATA_16; + scsi_cmd[1] = (3 << 1); /* Non-data */ + /* scsi_cmd[2] is already 0 -- no off.line, cc, or data xfer */ + scsi_cmd[4] = args[1]; + scsi_cmd[6] = args[2]; + scsi_cmd[8] = args[3]; + scsi_cmd[10] = args[4]; + scsi_cmd[12] = args[5]; + scsi_cmd[14] = args[0]; + + /* Good values for timeout and retries? Values below + from scsi_ioctl_send_command() for default case... */ + if (scsi_execute_req(scsidev, scsi_cmd, DMA_NONE, NULL, 0, &sshdr, + (10*HZ), 5)) + rc = -EIO; + + /* Need code to retrieve data from check condition? */ + return rc; +} + +int ata_scsi_ioctl(struct scsi_device *scsidev, int cmd, void __user *arg) +{ + int val = -EINVAL, rc = -EINVAL; + + switch (cmd) { + case ATA_IOC_GET_IO32: + val = 0; + if (copy_to_user(arg, &val, 1)) + return -EFAULT; + return 0; + + case ATA_IOC_SET_IO32: + val = (unsigned long) arg; + if (val != 0) + return -EINVAL; + return 0; + + case HDIO_DRIVE_CMD: + if (!capable(CAP_SYS_ADMIN) || !capable(CAP_SYS_RAWIO)) + return -EACCES; + return ata_cmd_ioctl(scsidev, arg); + + case HDIO_DRIVE_TASK: + if (!capable(CAP_SYS_ADMIN) || !capable(CAP_SYS_RAWIO)) + return -EACCES; + return ata_task_ioctl(scsidev, arg); + + default: + rc = -ENOTTY; + break; + } + + return rc; +} + +/** + * ata_scsi_qc_new - acquire new ata_queued_cmd reference + * @dev: ATA device to which the new command is attached + * @cmd: SCSI command that originated this ATA command + * @done: SCSI command completion function + * + * Obtain a reference to an unused ata_queued_cmd structure, + * which is the basic libata structure representing a single + * ATA command sent to the hardware. + * + * If a command was available, fill in the SCSI-specific + * portions of the structure with information on the + * current command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Command allocated, or %NULL if none available. + */ +struct ata_queued_cmd *ata_scsi_qc_new(struct ata_device *dev, + struct scsi_cmnd *cmd, + void (*done)(struct scsi_cmnd *)) +{ + struct ata_queued_cmd *qc; + + qc = ata_qc_new_init(dev); + if (qc) { + qc->scsicmd = cmd; + qc->scsidone = done; + + if (cmd->use_sg) { + qc->__sg = (struct scatterlist *) cmd->request_buffer; + qc->n_elem = cmd->use_sg; + } else { + qc->__sg = &qc->sgent; + qc->n_elem = 1; + } + } else { + cmd->result = (DID_OK << 16) | (QUEUE_FULL << 1); + done(cmd); + } + + return qc; +} + +/** + * ata_dump_status - user friendly display of error info + * @id: id of the port in question + * @tf: ptr to filled out taskfile + * + * Decode and dump the ATA error/status registers for the user so + * that they have some idea what really happened at the non + * make-believe layer. + * + * LOCKING: + * inherited from caller + */ +void ata_dump_status(unsigned id, struct ata_taskfile *tf) +{ + u8 stat = tf->command, err = tf->feature; + + printk(KERN_WARNING "ata%u: status=0x%02x { ", id, stat); + if (stat & ATA_BUSY) { + printk("Busy }\n"); /* Data is not valid in this case */ + } else { + if (stat & 0x40) printk("DriveReady "); + if (stat & 0x20) printk("DeviceFault "); + if (stat & 0x10) printk("SeekComplete "); + if (stat & 0x08) printk("DataRequest "); + if (stat & 0x04) printk("CorrectedError "); + if (stat & 0x02) printk("Index "); + if (stat & 0x01) printk("Error "); + printk("}\n"); + + if (err) { + printk(KERN_WARNING "ata%u: error=0x%02x { ", id, err); + if (err & 0x04) printk("DriveStatusError "); + if (err & 0x80) { + if (err & 0x04) printk("BadCRC "); + else printk("Sector "); + } + if (err & 0x40) printk("UncorrectableError "); + if (err & 0x10) printk("SectorIdNotFound "); + if (err & 0x02) printk("TrackZeroNotFound "); + if (err & 0x01) printk("AddrMarkNotFound "); + printk("}\n"); + } + } +} + +/** + * ata_scsi_device_suspend - suspend ATA device associated with sdev + * @sdev: the SCSI device to suspend + * @mesg: target power management message + * + * Request suspend EH action on the ATA device associated with + * @sdev and wait for the operation to complete. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t mesg) +{ + struct ata_port *ap = ata_shost_to_port(sdev->host); + struct ata_device *dev = ata_scsi_find_dev(ap, sdev); + unsigned long flags; + unsigned int action; + int rc = 0; + + if (!dev) + goto out; + + spin_lock_irqsave(ap->lock, flags); + + /* wait for the previous resume to complete */ + while (dev->flags & ATA_DFLAG_SUSPENDED) { + spin_unlock_irqrestore(ap->lock, flags); + ata_port_wait_eh(ap); + spin_lock_irqsave(ap->lock, flags); + } + + /* if @sdev is already detached, nothing to do */ + if (sdev->sdev_state == SDEV_OFFLINE || + sdev->sdev_state == SDEV_CANCEL || sdev->sdev_state == SDEV_DEL) + goto out_unlock; + + /* request suspend */ + action = ATA_EH_SUSPEND; + if (mesg.event != PM_EVENT_SUSPEND) + action |= ATA_EH_PM_FREEZE; + ap->eh_info.dev_action[dev->devno] |= action; + ap->eh_info.flags |= ATA_EHI_QUIET; + ata_port_schedule_eh(ap); + + spin_unlock_irqrestore(ap->lock, flags); + + /* wait for EH to do the job */ + ata_port_wait_eh(ap); + + spin_lock_irqsave(ap->lock, flags); + + /* If @sdev is still attached but the associated ATA device + * isn't suspended, the operation failed. + */ + if (sdev->sdev_state != SDEV_OFFLINE && + sdev->sdev_state != SDEV_CANCEL && sdev->sdev_state != SDEV_DEL && + !(dev->flags & ATA_DFLAG_SUSPENDED)) + rc = -EIO; + + out_unlock: + spin_unlock_irqrestore(ap->lock, flags); + out: + if (rc == 0) + sdev->sdev_gendev.power.power_state = mesg; + return rc; +} + +/** + * ata_scsi_device_resume - resume ATA device associated with sdev + * @sdev: the SCSI device to resume + * + * Request resume EH action on the ATA device associated with + * @sdev and return immediately. This enables parallel + * wakeup/spinup of devices. + * + * LOCKING: + * Kernel thread context (may sleep). + * + * RETURNS: + * 0. + */ +int ata_scsi_device_resume(struct scsi_device *sdev) +{ + struct ata_port *ap = ata_shost_to_port(sdev->host); + struct ata_device *dev = ata_scsi_find_dev(ap, sdev); + struct ata_eh_info *ehi = &ap->eh_info; + unsigned long flags; + unsigned int action; + + if (!dev) + goto out; + + spin_lock_irqsave(ap->lock, flags); + + /* if @sdev is already detached, nothing to do */ + if (sdev->sdev_state == SDEV_OFFLINE || + sdev->sdev_state == SDEV_CANCEL || sdev->sdev_state == SDEV_DEL) + goto out_unlock; + + /* request resume */ + action = ATA_EH_RESUME; + if (sdev->sdev_gendev.power.power_state.event == PM_EVENT_SUSPEND) + __ata_ehi_hotplugged(ehi); + else + action |= ATA_EH_PM_FREEZE | ATA_EH_SOFTRESET; + ehi->dev_action[dev->devno] |= action; + + /* We don't want autopsy and verbose EH messages. Disable + * those if we're the only device on this link. + */ + if (ata_port_max_devices(ap) == 1) + ehi->flags |= ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET; + + ata_port_schedule_eh(ap); + + out_unlock: + spin_unlock_irqrestore(ap->lock, flags); + out: + sdev->sdev_gendev.power.power_state = PMSG_ON; + return 0; +} + +/** + * ata_to_sense_error - convert ATA error to SCSI error + * @id: ATA device number + * @drv_stat: value contained in ATA status register + * @drv_err: value contained in ATA error register + * @sk: the sense key we'll fill out + * @asc: the additional sense code we'll fill out + * @ascq: the additional sense code qualifier we'll fill out + * @verbose: be verbose + * + * Converts an ATA error into a SCSI error. Fill out pointers to + * SK, ASC, and ASCQ bytes for later use in fixed or descriptor + * format sense blocks. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_to_sense_error(unsigned id, u8 drv_stat, u8 drv_err, u8 *sk, u8 *asc, + u8 *ascq, int verbose) +{ + int i; + + /* Based on the 3ware driver translation table */ + static const unsigned char sense_table[][4] = { + /* BBD|ECC|ID|MAR */ + {0xd1, ABORTED_COMMAND, 0x00, 0x00}, // Device busy Aborted command + /* BBD|ECC|ID */ + {0xd0, ABORTED_COMMAND, 0x00, 0x00}, // Device busy Aborted command + /* ECC|MC|MARK */ + {0x61, HARDWARE_ERROR, 0x00, 0x00}, // Device fault Hardware error + /* ICRC|ABRT */ /* NB: ICRC & !ABRT is BBD */ + {0x84, ABORTED_COMMAND, 0x47, 0x00}, // Data CRC error SCSI parity error + /* MC|ID|ABRT|TRK0|MARK */ + {0x37, NOT_READY, 0x04, 0x00}, // Unit offline Not ready + /* MCR|MARK */ + {0x09, NOT_READY, 0x04, 0x00}, // Unrecovered disk error Not ready + /* Bad address mark */ + {0x01, MEDIUM_ERROR, 0x13, 0x00}, // Address mark not found Address mark not found for data field + /* TRK0 */ + {0x02, HARDWARE_ERROR, 0x00, 0x00}, // Track 0 not found Hardware error + /* Abort & !ICRC */ + {0x04, ABORTED_COMMAND, 0x00, 0x00}, // Aborted command Aborted command + /* Media change request */ + {0x08, NOT_READY, 0x04, 0x00}, // Media change request FIXME: faking offline + /* SRV */ + {0x10, ABORTED_COMMAND, 0x14, 0x00}, // ID not found Recorded entity not found + /* Media change */ + {0x08, NOT_READY, 0x04, 0x00}, // Media change FIXME: faking offline + /* ECC */ + {0x40, MEDIUM_ERROR, 0x11, 0x04}, // Uncorrectable ECC error Unrecovered read error + /* BBD - block marked bad */ + {0x80, MEDIUM_ERROR, 0x11, 0x04}, // Block marked bad Medium error, unrecovered read error + {0xFF, 0xFF, 0xFF, 0xFF}, // END mark + }; + static const unsigned char stat_table[][4] = { + /* Must be first because BUSY means no other bits valid */ + {0x80, ABORTED_COMMAND, 0x47, 0x00}, // Busy, fake parity for now + {0x20, HARDWARE_ERROR, 0x00, 0x00}, // Device fault + {0x08, ABORTED_COMMAND, 0x47, 0x00}, // Timed out in xfer, fake parity for now + {0x04, RECOVERED_ERROR, 0x11, 0x00}, // Recovered ECC error Medium error, recovered + {0xFF, 0xFF, 0xFF, 0xFF}, // END mark + }; + + /* + * Is this an error we can process/parse + */ + if (drv_stat & ATA_BUSY) { + drv_err = 0; /* Ignore the err bits, they're invalid */ + } + + if (drv_err) { + /* Look for drv_err */ + for (i = 0; sense_table[i][0] != 0xFF; i++) { + /* Look for best matches first */ + if ((sense_table[i][0] & drv_err) == + sense_table[i][0]) { + *sk = sense_table[i][1]; + *asc = sense_table[i][2]; + *ascq = sense_table[i][3]; + goto translate_done; + } + } + /* No immediate match */ + if (verbose) + printk(KERN_WARNING "ata%u: no sense translation for " + "error 0x%02x\n", id, drv_err); + } + + /* Fall back to interpreting status bits */ + for (i = 0; stat_table[i][0] != 0xFF; i++) { + if (stat_table[i][0] & drv_stat) { + *sk = stat_table[i][1]; + *asc = stat_table[i][2]; + *ascq = stat_table[i][3]; + goto translate_done; + } + } + /* No error? Undecoded? */ + if (verbose) + printk(KERN_WARNING "ata%u: no sense translation for " + "status: 0x%02x\n", id, drv_stat); + + /* We need a sensible error return here, which is tricky, and one + that won't cause people to do things like return a disk wrongly */ + *sk = ABORTED_COMMAND; + *asc = 0x00; + *ascq = 0x00; + + translate_done: + if (verbose) + printk(KERN_ERR "ata%u: translated ATA stat/err 0x%02x/%02x " + "to SCSI SK/ASC/ASCQ 0x%x/%02x/%02x\n", + id, drv_stat, drv_err, *sk, *asc, *ascq); + return; +} + +/* + * ata_gen_ata_desc_sense - Generate check condition sense block. + * @qc: Command that completed. + * + * This function is specific to the ATA descriptor format sense + * block specified for the ATA pass through commands. Regardless + * of whether the command errored or not, return a sense + * block. Copy all controller registers into the sense + * block. Clear sense key, ASC & ASCQ if there is no error. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_gen_ata_desc_sense(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *cmd = qc->scsicmd; + struct ata_taskfile *tf = &qc->result_tf; + unsigned char *sb = cmd->sense_buffer; + unsigned char *desc = sb + 8; + int verbose = qc->ap->ops->error_handler == NULL; + + memset(sb, 0, SCSI_SENSE_BUFFERSIZE); + + cmd->result = (DRIVER_SENSE << 24) | SAM_STAT_CHECK_CONDITION; + + /* + * Use ata_to_sense_error() to map status register bits + * onto sense key, asc & ascq. + */ + if (qc->err_mask || + tf->command & (ATA_BUSY | ATA_DF | ATA_ERR | ATA_DRQ)) { + ata_to_sense_error(qc->ap->id, tf->command, tf->feature, + &sb[1], &sb[2], &sb[3], verbose); + sb[1] &= 0x0f; + } + + /* + * Sense data is current and format is descriptor. + */ + sb[0] = 0x72; + + desc[0] = 0x09; + + /* + * Set length of additional sense data. + * Since we only populate descriptor 0, the total + * length is the same (fixed) length as descriptor 0. + */ + desc[1] = sb[7] = 14; + + /* + * Copy registers into sense buffer. + */ + desc[2] = 0x00; + desc[3] = tf->feature; /* == error reg */ + desc[5] = tf->nsect; + desc[7] = tf->lbal; + desc[9] = tf->lbam; + desc[11] = tf->lbah; + desc[12] = tf->device; + desc[13] = tf->command; /* == status reg */ + + /* + * Fill in Extend bit, and the high order bytes + * if applicable. + */ + if (tf->flags & ATA_TFLAG_LBA48) { + desc[2] |= 0x01; + desc[4] = tf->hob_nsect; + desc[6] = tf->hob_lbal; + desc[8] = tf->hob_lbam; + desc[10] = tf->hob_lbah; + } +} + +/** + * ata_gen_fixed_sense - generate a SCSI fixed sense block + * @qc: Command that we are erroring out + * + * Leverage ata_to_sense_error() to give us the codes. Fit our + * LBA in here if there's room. + * + * LOCKING: + * inherited from caller + */ +void ata_gen_fixed_sense(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *cmd = qc->scsicmd; + struct ata_taskfile *tf = &qc->result_tf; + unsigned char *sb = cmd->sense_buffer; + int verbose = qc->ap->ops->error_handler == NULL; + + memset(sb, 0, SCSI_SENSE_BUFFERSIZE); + + cmd->result = (DRIVER_SENSE << 24) | SAM_STAT_CHECK_CONDITION; + + /* + * Use ata_to_sense_error() to map status register bits + * onto sense key, asc & ascq. + */ + if (qc->err_mask || + tf->command & (ATA_BUSY | ATA_DF | ATA_ERR | ATA_DRQ)) { + ata_to_sense_error(qc->ap->id, tf->command, tf->feature, + &sb[2], &sb[12], &sb[13], verbose); + sb[2] &= 0x0f; + } + + sb[0] = 0x70; + sb[7] = 0x0a; + + if (tf->flags & ATA_TFLAG_LBA48) { + /* TODO: find solution for LBA48 descriptors */ + } + + else if (tf->flags & ATA_TFLAG_LBA) { + /* A small (28b) LBA will fit in the 32b info field */ + sb[0] |= 0x80; /* set valid bit */ + sb[3] = tf->device & 0x0f; + sb[4] = tf->lbah; + sb[5] = tf->lbam; + sb[6] = tf->lbal; + } + + else { + /* TODO: C/H/S */ + } +} + +static void ata_scsi_sdev_config(struct scsi_device *sdev) +{ + sdev->use_10_for_rw = 1; + sdev->use_10_for_ms = 1; +} + +static void ata_scsi_dev_config(struct scsi_device *sdev, + struct ata_device *dev) +{ + unsigned int max_sectors; + + /* TODO: 2048 is an arbitrary number, not the + * hardware maximum. This should be increased to + * 65534 when Jens Axboe's patch for dynamically + * determining max_sectors is merged. + */ + max_sectors = ATA_MAX_SECTORS; + if (dev->flags & ATA_DFLAG_LBA48) + max_sectors = ATA_MAX_SECTORS_LBA48; + if (dev->max_sectors) + max_sectors = dev->max_sectors; + + blk_queue_max_sectors(sdev->request_queue, max_sectors); + + /* + * SATA DMA transfers must be multiples of 4 byte, so + * we need to pad ATAPI transfers using an extra sg. + * Decrement max hw segments accordingly. + */ + if (dev->class == ATA_DEV_ATAPI) { + request_queue_t *q = sdev->request_queue; + blk_queue_max_hw_segments(q, q->max_hw_segments - 1); + } + + if (dev->flags & ATA_DFLAG_NCQ) { + int depth; + + depth = min(sdev->host->can_queue, ata_id_queue_depth(dev->id)); + depth = min(ATA_MAX_QUEUE - 1, depth); + scsi_adjust_queue_depth(sdev, MSG_SIMPLE_TAG, depth); + } +} + +/** + * ata_scsi_slave_config - Set SCSI device attributes + * @sdev: SCSI device to examine + * + * This is called before we actually start reading + * and writing to the device, to configure certain + * SCSI mid-layer behaviors. + * + * LOCKING: + * Defined by SCSI layer. We don't really care. + */ + +int ata_scsi_slave_config(struct scsi_device *sdev) +{ + struct ata_port *ap = ata_shost_to_port(sdev->host); + struct ata_device *dev = __ata_scsi_find_dev(ap, sdev); + + ata_scsi_sdev_config(sdev); + + blk_queue_max_phys_segments(sdev->request_queue, LIBATA_MAX_PRD); + + if (dev) + ata_scsi_dev_config(sdev, dev); + + return 0; /* scsi layer doesn't check return value, sigh */ +} + +/** + * ata_scsi_slave_destroy - SCSI device is about to be destroyed + * @sdev: SCSI device to be destroyed + * + * @sdev is about to be destroyed for hot/warm unplugging. If + * this unplugging was initiated by libata as indicated by NULL + * dev->sdev, this function doesn't have to do anything. + * Otherwise, SCSI layer initiated warm-unplug is in progress. + * Clear dev->sdev, schedule the device for ATA detach and invoke + * EH. + * + * LOCKING: + * Defined by SCSI layer. We don't really care. + */ +void ata_scsi_slave_destroy(struct scsi_device *sdev) +{ + struct ata_port *ap = ata_shost_to_port(sdev->host); + unsigned long flags; + struct ata_device *dev; + + if (!ap->ops->error_handler) + return; + + spin_lock_irqsave(ap->lock, flags); + dev = __ata_scsi_find_dev(ap, sdev); + if (dev && dev->sdev) { + /* SCSI device already in CANCEL state, no need to offline it */ + dev->sdev = NULL; + dev->flags |= ATA_DFLAG_DETACH; + ata_port_schedule_eh(ap); + } + spin_unlock_irqrestore(ap->lock, flags); +} + +/** + * ata_scsi_change_queue_depth - SCSI callback for queue depth config + * @sdev: SCSI device to configure queue depth for + * @queue_depth: new queue depth + * + * This is libata standard hostt->change_queue_depth callback. + * SCSI will call into this callback when user tries to set queue + * depth via sysfs. + * + * LOCKING: + * SCSI layer (we don't care) + * + * RETURNS: + * Newly configured queue depth. + */ +int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth) +{ + struct ata_port *ap = ata_shost_to_port(sdev->host); + struct ata_device *dev; + int max_depth; + + if (queue_depth < 1) + return sdev->queue_depth; + + dev = ata_scsi_find_dev(ap, sdev); + if (!dev || !ata_dev_enabled(dev)) + return sdev->queue_depth; + + max_depth = min(sdev->host->can_queue, ata_id_queue_depth(dev->id)); + max_depth = min(ATA_MAX_QUEUE - 1, max_depth); + if (queue_depth > max_depth) + queue_depth = max_depth; + + scsi_adjust_queue_depth(sdev, MSG_SIMPLE_TAG, queue_depth); + return queue_depth; +} + +/** + * ata_scsi_start_stop_xlat - Translate SCSI START STOP UNIT command + * @qc: Storage for translated ATA taskfile + * @scsicmd: SCSI command to translate + * + * Sets up an ATA taskfile to issue STANDBY (to stop) or READ VERIFY + * (to start). Perhaps these commands should be preceded by + * CHECK POWER MODE to see what power mode the device is already in. + * [See SAT revision 5 at www.t10.org] + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, non-zero on error. + */ + +static unsigned int ata_scsi_start_stop_xlat(struct ata_queued_cmd *qc, + const u8 *scsicmd) +{ + struct ata_taskfile *tf = &qc->tf; + + tf->flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR; + tf->protocol = ATA_PROT_NODATA; + if (scsicmd[1] & 0x1) { + ; /* ignore IMMED bit, violates sat-r05 */ + } + if (scsicmd[4] & 0x2) + goto invalid_fld; /* LOEJ bit set not supported */ + if (((scsicmd[4] >> 4) & 0xf) != 0) + goto invalid_fld; /* power conditions not supported */ + if (scsicmd[4] & 0x1) { + tf->nsect = 1; /* 1 sector, lba=0 */ + + if (qc->dev->flags & ATA_DFLAG_LBA) { + tf->flags |= ATA_TFLAG_LBA; + + tf->lbah = 0x0; + tf->lbam = 0x0; + tf->lbal = 0x0; + tf->device |= ATA_LBA; + } else { + /* CHS */ + tf->lbal = 0x1; /* sect */ + tf->lbam = 0x0; /* cyl low */ + tf->lbah = 0x0; /* cyl high */ + } + + tf->command = ATA_CMD_VERIFY; /* READ VERIFY */ + } else { + tf->nsect = 0; /* time period value (0 implies now) */ + tf->command = ATA_CMD_STANDBY; + /* Consider: ATA STANDBY IMMEDIATE command */ + } + /* + * Standby and Idle condition timers could be implemented but that + * would require libata to implement the Power condition mode page + * and allow the user to change it. Changing mode pages requires + * MODE SELECT to be implemented. + */ + + return 0; + +invalid_fld: + ata_scsi_set_sense(qc->scsicmd, ILLEGAL_REQUEST, 0x24, 0x0); + /* "Invalid field in cbd" */ + return 1; +} + + +/** + * ata_scsi_flush_xlat - Translate SCSI SYNCHRONIZE CACHE command + * @qc: Storage for translated ATA taskfile + * @scsicmd: SCSI command to translate (ignored) + * + * Sets up an ATA taskfile to issue FLUSH CACHE or + * FLUSH CACHE EXT. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, non-zero on error. + */ + +static unsigned int ata_scsi_flush_xlat(struct ata_queued_cmd *qc, const u8 *scsicmd) +{ + struct ata_taskfile *tf = &qc->tf; + + tf->flags |= ATA_TFLAG_DEVICE; + tf->protocol = ATA_PROT_NODATA; + + if ((qc->dev->flags & ATA_DFLAG_LBA48) && + (ata_id_has_flush_ext(qc->dev->id))) + tf->command = ATA_CMD_FLUSH_EXT; + else + tf->command = ATA_CMD_FLUSH; + + return 0; +} + +/** + * scsi_6_lba_len - Get LBA and transfer length + * @scsicmd: SCSI command to translate + * + * Calculate LBA and transfer length for 6-byte commands. + * + * RETURNS: + * @plba: the LBA + * @plen: the transfer length + */ + +static void scsi_6_lba_len(const u8 *scsicmd, u64 *plba, u32 *plen) +{ + u64 lba = 0; + u32 len = 0; + + VPRINTK("six-byte command\n"); + + lba |= ((u64)scsicmd[2]) << 8; + lba |= ((u64)scsicmd[3]); + + len |= ((u32)scsicmd[4]); + + *plba = lba; + *plen = len; +} + +/** + * scsi_10_lba_len - Get LBA and transfer length + * @scsicmd: SCSI command to translate + * + * Calculate LBA and transfer length for 10-byte commands. + * + * RETURNS: + * @plba: the LBA + * @plen: the transfer length + */ + +static void scsi_10_lba_len(const u8 *scsicmd, u64 *plba, u32 *plen) +{ + u64 lba = 0; + u32 len = 0; + + VPRINTK("ten-byte command\n"); + + lba |= ((u64)scsicmd[2]) << 24; + lba |= ((u64)scsicmd[3]) << 16; + lba |= ((u64)scsicmd[4]) << 8; + lba |= ((u64)scsicmd[5]); + + len |= ((u32)scsicmd[7]) << 8; + len |= ((u32)scsicmd[8]); + + *plba = lba; + *plen = len; +} + +/** + * scsi_16_lba_len - Get LBA and transfer length + * @scsicmd: SCSI command to translate + * + * Calculate LBA and transfer length for 16-byte commands. + * + * RETURNS: + * @plba: the LBA + * @plen: the transfer length + */ + +static void scsi_16_lba_len(const u8 *scsicmd, u64 *plba, u32 *plen) +{ + u64 lba = 0; + u32 len = 0; + + VPRINTK("sixteen-byte command\n"); + + lba |= ((u64)scsicmd[2]) << 56; + lba |= ((u64)scsicmd[3]) << 48; + lba |= ((u64)scsicmd[4]) << 40; + lba |= ((u64)scsicmd[5]) << 32; + lba |= ((u64)scsicmd[6]) << 24; + lba |= ((u64)scsicmd[7]) << 16; + lba |= ((u64)scsicmd[8]) << 8; + lba |= ((u64)scsicmd[9]); + + len |= ((u32)scsicmd[10]) << 24; + len |= ((u32)scsicmd[11]) << 16; + len |= ((u32)scsicmd[12]) << 8; + len |= ((u32)scsicmd[13]); + + *plba = lba; + *plen = len; +} + +/** + * ata_scsi_verify_xlat - Translate SCSI VERIFY command into an ATA one + * @qc: Storage for translated ATA taskfile + * @scsicmd: SCSI command to translate + * + * Converts SCSI VERIFY command to an ATA READ VERIFY command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, non-zero on error. + */ + +static unsigned int ata_scsi_verify_xlat(struct ata_queued_cmd *qc, const u8 *scsicmd) +{ + struct ata_taskfile *tf = &qc->tf; + struct ata_device *dev = qc->dev; + u64 dev_sectors = qc->dev->n_sectors; + u64 block; + u32 n_block; + + tf->flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + tf->protocol = ATA_PROT_NODATA; + + if (scsicmd[0] == VERIFY) + scsi_10_lba_len(scsicmd, &block, &n_block); + else if (scsicmd[0] == VERIFY_16) + scsi_16_lba_len(scsicmd, &block, &n_block); + else + goto invalid_fld; + + if (!n_block) + goto nothing_to_do; + if (block >= dev_sectors) + goto out_of_range; + if ((block + n_block) > dev_sectors) + goto out_of_range; + + if (dev->flags & ATA_DFLAG_LBA) { + tf->flags |= ATA_TFLAG_LBA; + + if (lba_28_ok(block, n_block)) { + /* use LBA28 */ + tf->command = ATA_CMD_VERIFY; + tf->device |= (block >> 24) & 0xf; + } else if (lba_48_ok(block, n_block)) { + if (!(dev->flags & ATA_DFLAG_LBA48)) + goto out_of_range; + + /* use LBA48 */ + tf->flags |= ATA_TFLAG_LBA48; + tf->command = ATA_CMD_VERIFY_EXT; + + tf->hob_nsect = (n_block >> 8) & 0xff; + + tf->hob_lbah = (block >> 40) & 0xff; + tf->hob_lbam = (block >> 32) & 0xff; + tf->hob_lbal = (block >> 24) & 0xff; + } else + /* request too large even for LBA48 */ + goto out_of_range; + + tf->nsect = n_block & 0xff; + + tf->lbah = (block >> 16) & 0xff; + tf->lbam = (block >> 8) & 0xff; + tf->lbal = block & 0xff; + + tf->device |= ATA_LBA; + } else { + /* CHS */ + u32 sect, head, cyl, track; + + if (!lba_28_ok(block, n_block)) + goto out_of_range; + + /* Convert LBA to CHS */ + track = (u32)block / dev->sectors; + cyl = track / dev->heads; + head = track % dev->heads; + sect = (u32)block % dev->sectors + 1; + + DPRINTK("block %u track %u cyl %u head %u sect %u\n", + (u32)block, track, cyl, head, sect); + + /* Check whether the converted CHS can fit. + Cylinder: 0-65535 + Head: 0-15 + Sector: 1-255*/ + if ((cyl >> 16) || (head >> 4) || (sect >> 8) || (!sect)) + goto out_of_range; + + tf->command = ATA_CMD_VERIFY; + tf->nsect = n_block & 0xff; /* Sector count 0 means 256 sectors */ + tf->lbal = sect; + tf->lbam = cyl; + tf->lbah = cyl >> 8; + tf->device |= head; + } + + return 0; + +invalid_fld: + ata_scsi_set_sense(qc->scsicmd, ILLEGAL_REQUEST, 0x24, 0x0); + /* "Invalid field in cbd" */ + return 1; + +out_of_range: + ata_scsi_set_sense(qc->scsicmd, ILLEGAL_REQUEST, 0x21, 0x0); + /* "Logical Block Address out of range" */ + return 1; + +nothing_to_do: + qc->scsicmd->result = SAM_STAT_GOOD; + return 1; +} + +/** + * ata_scsi_rw_xlat - Translate SCSI r/w command into an ATA one + * @qc: Storage for translated ATA taskfile + * @scsicmd: SCSI command to translate + * + * Converts any of six SCSI read/write commands into the + * ATA counterpart, including starting sector (LBA), + * sector count, and taking into account the device's LBA48 + * support. + * + * Commands %READ_6, %READ_10, %READ_16, %WRITE_6, %WRITE_10, and + * %WRITE_16 are currently supported. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, non-zero on error. + */ + +static unsigned int ata_scsi_rw_xlat(struct ata_queued_cmd *qc, const u8 *scsicmd) +{ + struct ata_taskfile *tf = &qc->tf; + struct ata_device *dev = qc->dev; + u64 block; + u32 n_block; + + qc->flags |= ATA_QCFLAG_IO; + tf->flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + + if (scsicmd[0] == WRITE_10 || scsicmd[0] == WRITE_6 || + scsicmd[0] == WRITE_16) + tf->flags |= ATA_TFLAG_WRITE; + + /* Calculate the SCSI LBA, transfer length and FUA. */ + switch (scsicmd[0]) { + case READ_10: + case WRITE_10: + scsi_10_lba_len(scsicmd, &block, &n_block); + if (unlikely(scsicmd[1] & (1 << 3))) + tf->flags |= ATA_TFLAG_FUA; + break; + case READ_6: + case WRITE_6: + scsi_6_lba_len(scsicmd, &block, &n_block); + + /* for 6-byte r/w commands, transfer length 0 + * means 256 blocks of data, not 0 block. + */ + if (!n_block) + n_block = 256; + break; + case READ_16: + case WRITE_16: + scsi_16_lba_len(scsicmd, &block, &n_block); + if (unlikely(scsicmd[1] & (1 << 3))) + tf->flags |= ATA_TFLAG_FUA; + break; + default: + DPRINTK("no-byte command\n"); + goto invalid_fld; + } + + /* Check and compose ATA command */ + if (!n_block) + /* For 10-byte and 16-byte SCSI R/W commands, transfer + * length 0 means transfer 0 block of data. + * However, for ATA R/W commands, sector count 0 means + * 256 or 65536 sectors, not 0 sectors as in SCSI. + * + * WARNING: one or two older ATA drives treat 0 as 0... + */ + goto nothing_to_do; + + if ((dev->flags & (ATA_DFLAG_PIO | ATA_DFLAG_NCQ)) == ATA_DFLAG_NCQ) { + /* yay, NCQ */ + if (!lba_48_ok(block, n_block)) + goto out_of_range; + + tf->protocol = ATA_PROT_NCQ; + tf->flags |= ATA_TFLAG_LBA | ATA_TFLAG_LBA48; + + if (tf->flags & ATA_TFLAG_WRITE) + tf->command = ATA_CMD_FPDMA_WRITE; + else + tf->command = ATA_CMD_FPDMA_READ; + + qc->nsect = n_block; + + tf->nsect = qc->tag << 3; + tf->hob_feature = (n_block >> 8) & 0xff; + tf->feature = n_block & 0xff; + + tf->hob_lbah = (block >> 40) & 0xff; + tf->hob_lbam = (block >> 32) & 0xff; + tf->hob_lbal = (block >> 24) & 0xff; + tf->lbah = (block >> 16) & 0xff; + tf->lbam = (block >> 8) & 0xff; + tf->lbal = block & 0xff; + + tf->device = 1 << 6; + if (tf->flags & ATA_TFLAG_FUA) + tf->device |= 1 << 7; + } else if (dev->flags & ATA_DFLAG_LBA) { + tf->flags |= ATA_TFLAG_LBA; + + if (lba_28_ok(block, n_block)) { + /* use LBA28 */ + tf->device |= (block >> 24) & 0xf; + } else if (lba_48_ok(block, n_block)) { + if (!(dev->flags & ATA_DFLAG_LBA48)) + goto out_of_range; + + /* use LBA48 */ + tf->flags |= ATA_TFLAG_LBA48; + + tf->hob_nsect = (n_block >> 8) & 0xff; + + tf->hob_lbah = (block >> 40) & 0xff; + tf->hob_lbam = (block >> 32) & 0xff; + tf->hob_lbal = (block >> 24) & 0xff; + } else + /* request too large even for LBA48 */ + goto out_of_range; + + if (unlikely(ata_rwcmd_protocol(qc) < 0)) + goto invalid_fld; + + qc->nsect = n_block; + tf->nsect = n_block & 0xff; + + tf->lbah = (block >> 16) & 0xff; + tf->lbam = (block >> 8) & 0xff; + tf->lbal = block & 0xff; + + tf->device |= ATA_LBA; + } else { + /* CHS */ + u32 sect, head, cyl, track; + + /* The request -may- be too large for CHS addressing. */ + if (!lba_28_ok(block, n_block)) + goto out_of_range; + + if (unlikely(ata_rwcmd_protocol(qc) < 0)) + goto invalid_fld; + + /* Convert LBA to CHS */ + track = (u32)block / dev->sectors; + cyl = track / dev->heads; + head = track % dev->heads; + sect = (u32)block % dev->sectors + 1; + + DPRINTK("block %u track %u cyl %u head %u sect %u\n", + (u32)block, track, cyl, head, sect); + + /* Check whether the converted CHS can fit. + Cylinder: 0-65535 + Head: 0-15 + Sector: 1-255*/ + if ((cyl >> 16) || (head >> 4) || (sect >> 8) || (!sect)) + goto out_of_range; + + qc->nsect = n_block; + tf->nsect = n_block & 0xff; /* Sector count 0 means 256 sectors */ + tf->lbal = sect; + tf->lbam = cyl; + tf->lbah = cyl >> 8; + tf->device |= head; + } + + return 0; + +invalid_fld: + ata_scsi_set_sense(qc->scsicmd, ILLEGAL_REQUEST, 0x24, 0x0); + /* "Invalid field in cbd" */ + return 1; + +out_of_range: + ata_scsi_set_sense(qc->scsicmd, ILLEGAL_REQUEST, 0x21, 0x0); + /* "Logical Block Address out of range" */ + return 1; + +nothing_to_do: + qc->scsicmd->result = SAM_STAT_GOOD; + return 1; +} + +static void ata_scsi_qc_complete(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *cmd = qc->scsicmd; + u8 *cdb = cmd->cmnd; + int need_sense = (qc->err_mask != 0); + + /* We snoop the SET_FEATURES - Write Cache ON/OFF command, and + * schedule EH_REVALIDATE operation to update the IDENTIFY DEVICE + * cache + */ + if (!need_sense && (qc->tf.command == ATA_CMD_SET_FEATURES) && + ((qc->tf.feature == SETFEATURES_WC_ON) || + (qc->tf.feature == SETFEATURES_WC_OFF))) { + qc->ap->eh_info.action |= ATA_EH_REVALIDATE; + ata_port_schedule_eh(qc->ap); + } + + /* For ATA pass thru (SAT) commands, generate a sense block if + * user mandated it or if there's an error. Note that if we + * generate because the user forced us to, a check condition + * is generated and the ATA register values are returned + * whether the command completed successfully or not. If there + * was no error, SK, ASC and ASCQ will all be zero. + */ + if (((cdb[0] == ATA_16) || (cdb[0] == ATA_12)) && + ((cdb[2] & 0x20) || need_sense)) { + ata_gen_ata_desc_sense(qc); + } else { + if (!need_sense) { + cmd->result = SAM_STAT_GOOD; + } else { + /* TODO: decide which descriptor format to use + * for 48b LBA devices and call that here + * instead of the fixed desc, which is only + * good for smaller LBA (and maybe CHS?) + * devices. + */ + ata_gen_fixed_sense(qc); + } + } + + if (need_sense && !qc->ap->ops->error_handler) + ata_dump_status(qc->ap->id, &qc->result_tf); + + qc->scsidone(cmd); + + ata_qc_free(qc); +} + +/** + * ata_scmd_need_defer - Check whether we need to defer scmd + * @dev: ATA device to which the command is addressed + * @is_io: Is the command IO (and thus possibly NCQ)? + * + * NCQ and non-NCQ commands cannot run together. As upper layer + * only knows the queue depth, we are responsible for maintaining + * exclusion. This function checks whether a new command can be + * issued to @dev. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * 1 if deferring is needed, 0 otherwise. + */ +static int ata_scmd_need_defer(struct ata_device *dev, int is_io) +{ + struct ata_port *ap = dev->ap; + + if (!(dev->flags & ATA_DFLAG_NCQ)) + return 0; + + if (is_io) { + if (!ata_tag_valid(ap->active_tag)) + return 0; + } else { + if (!ata_tag_valid(ap->active_tag) && !ap->sactive) + return 0; + } + return 1; +} + +/** + * ata_scsi_translate - Translate then issue SCSI command to ATA device + * @dev: ATA device to which the command is addressed + * @cmd: SCSI command to execute + * @done: SCSI command completion function + * @xlat_func: Actor which translates @cmd to an ATA taskfile + * + * Our ->queuecommand() function has decided that the SCSI + * command issued can be directly translated into an ATA + * command, rather than handled internally. + * + * This function sets up an ata_queued_cmd structure for the + * SCSI command, and sends that ata_queued_cmd to the hardware. + * + * The xlat_func argument (actor) returns 0 if ready to execute + * ATA command, else 1 to finish translation. If 1 is returned + * then cmd->result (and possibly cmd->sense_buffer) are assumed + * to be set reflecting an error condition or clean (early) + * termination. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * 0 on success, SCSI_ML_QUEUE_DEVICE_BUSY if the command + * needs to be deferred. + */ +static int ata_scsi_translate(struct ata_device *dev, struct scsi_cmnd *cmd, + void (*done)(struct scsi_cmnd *), + ata_xlat_func_t xlat_func) +{ + struct ata_queued_cmd *qc; + u8 *scsicmd = cmd->cmnd; + int is_io = xlat_func == ata_scsi_rw_xlat; + + VPRINTK("ENTER\n"); + + if (unlikely(ata_scmd_need_defer(dev, is_io))) + goto defer; + + qc = ata_scsi_qc_new(dev, cmd, done); + if (!qc) + goto err_mem; + + /* data is present; dma-map it */ + if (cmd->sc_data_direction == DMA_FROM_DEVICE || + cmd->sc_data_direction == DMA_TO_DEVICE) { + if (unlikely(cmd->request_bufflen < 1)) { + ata_dev_printk(dev, KERN_WARNING, + "WARNING: zero len r/w req\n"); + goto err_did; + } + + if (cmd->use_sg) + ata_sg_init(qc, cmd->request_buffer, cmd->use_sg); + else + ata_sg_init_one(qc, cmd->request_buffer, + cmd->request_bufflen); + + qc->dma_dir = cmd->sc_data_direction; + } + + qc->complete_fn = ata_scsi_qc_complete; + + if (xlat_func(qc, scsicmd)) + goto early_finish; + + /* select device, send command to hardware */ + ata_qc_issue(qc); + + VPRINTK("EXIT\n"); + return 0; + +early_finish: + ata_qc_free(qc); + done(cmd); + DPRINTK("EXIT - early finish (good or error)\n"); + return 0; + +err_did: + ata_qc_free(qc); +err_mem: + cmd->result = (DID_ERROR << 16); + done(cmd); + DPRINTK("EXIT - internal\n"); + return 0; + +defer: + DPRINTK("EXIT - defer\n"); + return SCSI_MLQUEUE_DEVICE_BUSY; +} + +/** + * ata_scsi_rbuf_get - Map response buffer. + * @cmd: SCSI command containing buffer to be mapped. + * @buf_out: Pointer to mapped area. + * + * Maps buffer contained within SCSI command @cmd. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Length of response buffer. + */ + +static unsigned int ata_scsi_rbuf_get(struct scsi_cmnd *cmd, u8 **buf_out) +{ + u8 *buf; + unsigned int buflen; + + if (cmd->use_sg) { + struct scatterlist *sg; + + sg = (struct scatterlist *) cmd->request_buffer; + buf = kmap_atomic(sg->page, KM_USER0) + sg->offset; + buflen = sg->length; + } else { + buf = cmd->request_buffer; + buflen = cmd->request_bufflen; + } + + *buf_out = buf; + return buflen; +} + +/** + * ata_scsi_rbuf_put - Unmap response buffer. + * @cmd: SCSI command containing buffer to be unmapped. + * @buf: buffer to unmap + * + * Unmaps response buffer contained within @cmd. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf) +{ + if (cmd->use_sg) { + struct scatterlist *sg; + + sg = (struct scatterlist *) cmd->request_buffer; + kunmap_atomic(buf - sg->offset, KM_USER0); + } +} + +/** + * ata_scsi_rbuf_fill - wrapper for SCSI command simulators + * @args: device IDENTIFY data / SCSI command of interest. + * @actor: Callback hook for desired SCSI command simulator + * + * Takes care of the hard work of simulating a SCSI command... + * Mapping the response buffer, calling the command's handler, + * and handling the handler's return value. This return value + * indicates whether the handler wishes the SCSI command to be + * completed successfully (0), or not (in which case cmd->result + * and sense buffer are assumed to be set). + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +void ata_scsi_rbuf_fill(struct ata_scsi_args *args, + unsigned int (*actor) (struct ata_scsi_args *args, + u8 *rbuf, unsigned int buflen)) +{ + u8 *rbuf; + unsigned int buflen, rc; + struct scsi_cmnd *cmd = args->cmd; + + buflen = ata_scsi_rbuf_get(cmd, &rbuf); + memset(rbuf, 0, buflen); + rc = actor(args, rbuf, buflen); + ata_scsi_rbuf_put(cmd, rbuf); + + if (rc == 0) + cmd->result = SAM_STAT_GOOD; + args->done(cmd); +} + +/** + * ata_scsiop_inq_std - Simulate INQUIRY command + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * Returns standard device identification data associated + * with non-VPD INQUIRY command output. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + u8 hdr[] = { + TYPE_DISK, + 0, + 0x5, /* claim SPC-3 version compatibility */ + 2, + 95 - 4 + }; + + /* set scsi removeable (RMB) bit per ata bit */ + if (ata_id_removeable(args->id)) + hdr[1] |= (1 << 7); + + VPRINTK("ENTER\n"); + + memcpy(rbuf, hdr, sizeof(hdr)); + + if (buflen > 35) { + memcpy(&rbuf[8], "ATA ", 8); + ata_id_string(args->id, &rbuf[16], ATA_ID_PROD_OFS, 16); + ata_id_string(args->id, &rbuf[32], ATA_ID_FW_REV_OFS, 4); + if (rbuf[32] == 0 || rbuf[32] == ' ') + memcpy(&rbuf[32], "n/a ", 4); + } + + if (buflen > 63) { + const u8 versions[] = { + 0x60, /* SAM-3 (no version claimed) */ + + 0x03, + 0x20, /* SBC-2 (no version claimed) */ + + 0x02, + 0x60 /* SPC-3 (no version claimed) */ + }; + + memcpy(rbuf + 59, versions, sizeof(versions)); + } + + return 0; +} + +/** + * ata_scsiop_inq_00 - Simulate INQUIRY VPD page 0, list of pages + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * Returns list of inquiry VPD pages available. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + const u8 pages[] = { + 0x00, /* page 0x00, this page */ + 0x80, /* page 0x80, unit serial no page */ + 0x83 /* page 0x83, device ident page */ + }; + rbuf[3] = sizeof(pages); /* number of supported VPD pages */ + + if (buflen > 6) + memcpy(rbuf + 4, pages, sizeof(pages)); + + return 0; +} + +/** + * ata_scsiop_inq_80 - Simulate INQUIRY VPD page 80, device serial number + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * Returns ATA device serial number. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + const u8 hdr[] = { + 0, + 0x80, /* this page code */ + 0, + ATA_SERNO_LEN, /* page len */ + }; + memcpy(rbuf, hdr, sizeof(hdr)); + + if (buflen > (ATA_SERNO_LEN + 4 - 1)) + ata_id_string(args->id, (unsigned char *) &rbuf[4], + ATA_ID_SERNO_OFS, ATA_SERNO_LEN); + + return 0; +} + +/** + * ata_scsiop_inq_83 - Simulate INQUIRY VPD page 83, device identity + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * Yields two logical unit device identification designators: + * - vendor specific ASCII containing the ATA serial number + * - SAT defined "t10 vendor id based" containing ASCII vendor + * name ("ATA "), model and serial numbers. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + int num; + const int sat_model_serial_desc_len = 68; + const int ata_model_byte_len = 40; + + rbuf[1] = 0x83; /* this page code */ + num = 4; + + if (buflen > (ATA_SERNO_LEN + num + 3)) { + /* piv=0, assoc=lu, code_set=ACSII, designator=vendor */ + rbuf[num + 0] = 2; + rbuf[num + 3] = ATA_SERNO_LEN; + num += 4; + ata_id_string(args->id, (unsigned char *) rbuf + num, + ATA_ID_SERNO_OFS, ATA_SERNO_LEN); + num += ATA_SERNO_LEN; + } + if (buflen > (sat_model_serial_desc_len + num + 3)) { + /* SAT defined lu model and serial numbers descriptor */ + /* piv=0, assoc=lu, code_set=ACSII, designator=t10 vendor id */ + rbuf[num + 0] = 2; + rbuf[num + 1] = 1; + rbuf[num + 3] = sat_model_serial_desc_len; + num += 4; + memcpy(rbuf + num, "ATA ", 8); + num += 8; + ata_id_string(args->id, (unsigned char *) rbuf + num, + ATA_ID_PROD_OFS, ata_model_byte_len); + num += ata_model_byte_len; + ata_id_string(args->id, (unsigned char *) rbuf + num, + ATA_ID_SERNO_OFS, ATA_SERNO_LEN); + num += ATA_SERNO_LEN; + } + rbuf[3] = num - 4; /* page len (assume less than 256 bytes) */ + return 0; +} + +/** + * ata_scsiop_noop - Command handler that simply returns success. + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * No operation. Simply returns success to caller, to indicate + * that the caller should successfully complete this SCSI command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_noop(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + VPRINTK("ENTER\n"); + return 0; +} + +/** + * ata_msense_push - Push data onto MODE SENSE data output buffer + * @ptr_io: (input/output) Location to store more output data + * @last: End of output data buffer + * @buf: Pointer to BLOB being added to output buffer + * @buflen: Length of BLOB + * + * Store MODE SENSE data on an output buffer. + * + * LOCKING: + * None. + */ + +static void ata_msense_push(u8 **ptr_io, const u8 *last, + const u8 *buf, unsigned int buflen) +{ + u8 *ptr = *ptr_io; + + if ((ptr + buflen - 1) > last) + return; + + memcpy(ptr, buf, buflen); + + ptr += buflen; + + *ptr_io = ptr; +} + +/** + * ata_msense_caching - Simulate MODE SENSE caching info page + * @id: device IDENTIFY data + * @ptr_io: (input/output) Location to store more output data + * @last: End of output data buffer + * + * Generate a caching info page, which conditionally indicates + * write caching to the SCSI layer, depending on device + * capabilities. + * + * LOCKING: + * None. + */ + +static unsigned int ata_msense_caching(u16 *id, u8 **ptr_io, + const u8 *last) +{ + u8 page[CACHE_MPAGE_LEN]; + + memcpy(page, def_cache_mpage, sizeof(page)); + if (ata_id_wcache_enabled(id)) + page[2] |= (1 << 2); /* write cache enable */ + if (!ata_id_rahead_enabled(id)) + page[12] |= (1 << 5); /* disable read ahead */ + + ata_msense_push(ptr_io, last, page, sizeof(page)); + return sizeof(page); +} + +/** + * ata_msense_ctl_mode - Simulate MODE SENSE control mode page + * @dev: Device associated with this MODE SENSE command + * @ptr_io: (input/output) Location to store more output data + * @last: End of output data buffer + * + * Generate a generic MODE SENSE control mode page. + * + * LOCKING: + * None. + */ + +static unsigned int ata_msense_ctl_mode(u8 **ptr_io, const u8 *last) +{ + ata_msense_push(ptr_io, last, def_control_mpage, + sizeof(def_control_mpage)); + return sizeof(def_control_mpage); +} + +/** + * ata_msense_rw_recovery - Simulate MODE SENSE r/w error recovery page + * @dev: Device associated with this MODE SENSE command + * @ptr_io: (input/output) Location to store more output data + * @last: End of output data buffer + * + * Generate a generic MODE SENSE r/w error recovery page. + * + * LOCKING: + * None. + */ + +static unsigned int ata_msense_rw_recovery(u8 **ptr_io, const u8 *last) +{ + + ata_msense_push(ptr_io, last, def_rw_recovery_mpage, + sizeof(def_rw_recovery_mpage)); + return sizeof(def_rw_recovery_mpage); +} + +/* + * We can turn this into a real blacklist if it's needed, for now just + * blacklist any Maxtor BANC1G10 revision firmware + */ +static int ata_dev_supports_fua(u16 *id) +{ + unsigned char model[41], fw[9]; + + if (!libata_fua) + return 0; + if (!ata_id_has_fua(id)) + return 0; + + ata_id_c_string(id, model, ATA_ID_PROD_OFS, sizeof(model)); + ata_id_c_string(id, fw, ATA_ID_FW_REV_OFS, sizeof(fw)); + + if (strcmp(model, "Maxtor")) + return 1; + if (strcmp(fw, "BANC1G10")) + return 1; + + return 0; /* blacklisted */ +} + +/** + * ata_scsiop_mode_sense - Simulate MODE SENSE 6, 10 commands + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * Simulate MODE SENSE commands. Assume this is invoked for direct + * access devices (e.g. disks) only. There should be no block + * descriptor for other device types. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + struct ata_device *dev = args->dev; + u8 *scsicmd = args->cmd->cmnd, *p, *last; + const u8 sat_blk_desc[] = { + 0, 0, 0, 0, /* number of blocks: sat unspecified */ + 0, + 0, 0x2, 0x0 /* block length: 512 bytes */ + }; + u8 pg, spg; + unsigned int ebd, page_control, six_byte, output_len, alloc_len, minlen; + u8 dpofua; + + VPRINTK("ENTER\n"); + + six_byte = (scsicmd[0] == MODE_SENSE); + ebd = !(scsicmd[1] & 0x8); /* dbd bit inverted == edb */ + /* + * LLBA bit in msense(10) ignored (compliant) + */ + + page_control = scsicmd[2] >> 6; + switch (page_control) { + case 0: /* current */ + break; /* supported */ + case 3: /* saved */ + goto saving_not_supp; + case 1: /* changeable */ + case 2: /* defaults */ + default: + goto invalid_fld; + } + + if (six_byte) { + output_len = 4 + (ebd ? 8 : 0); + alloc_len = scsicmd[4]; + } else { + output_len = 8 + (ebd ? 8 : 0); + alloc_len = (scsicmd[7] << 8) + scsicmd[8]; + } + minlen = (alloc_len < buflen) ? alloc_len : buflen; + + p = rbuf + output_len; + last = rbuf + minlen - 1; + + pg = scsicmd[2] & 0x3f; + spg = scsicmd[3]; + /* + * No mode subpages supported (yet) but asking for _all_ + * subpages may be valid + */ + if (spg && (spg != ALL_SUB_MPAGES)) + goto invalid_fld; + + switch(pg) { + case RW_RECOVERY_MPAGE: + output_len += ata_msense_rw_recovery(&p, last); + break; + + case CACHE_MPAGE: + output_len += ata_msense_caching(args->id, &p, last); + break; + + case CONTROL_MPAGE: { + output_len += ata_msense_ctl_mode(&p, last); + break; + } + + case ALL_MPAGES: + output_len += ata_msense_rw_recovery(&p, last); + output_len += ata_msense_caching(args->id, &p, last); + output_len += ata_msense_ctl_mode(&p, last); + break; + + default: /* invalid page code */ + goto invalid_fld; + } + + if (minlen < 1) + return 0; + + dpofua = 0; + if (ata_dev_supports_fua(args->id) && (dev->flags & ATA_DFLAG_LBA48) && + (!(dev->flags & ATA_DFLAG_PIO) || dev->multi_count)) + dpofua = 1 << 4; + + if (six_byte) { + output_len--; + rbuf[0] = output_len; + if (minlen > 2) + rbuf[2] |= dpofua; + if (ebd) { + if (minlen > 3) + rbuf[3] = sizeof(sat_blk_desc); + if (minlen > 11) + memcpy(rbuf + 4, sat_blk_desc, + sizeof(sat_blk_desc)); + } + } else { + output_len -= 2; + rbuf[0] = output_len >> 8; + if (minlen > 1) + rbuf[1] = output_len; + if (minlen > 3) + rbuf[3] |= dpofua; + if (ebd) { + if (minlen > 7) + rbuf[7] = sizeof(sat_blk_desc); + if (minlen > 15) + memcpy(rbuf + 8, sat_blk_desc, + sizeof(sat_blk_desc)); + } + } + return 0; + +invalid_fld: + ata_scsi_set_sense(args->cmd, ILLEGAL_REQUEST, 0x24, 0x0); + /* "Invalid field in cbd" */ + return 1; + +saving_not_supp: + ata_scsi_set_sense(args->cmd, ILLEGAL_REQUEST, 0x39, 0x0); + /* "Saving parameters not supported" */ + return 1; +} + +/** + * ata_scsiop_read_cap - Simulate READ CAPACITY[ 16] commands + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * Simulate READ CAPACITY commands. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + u64 n_sectors; + u32 tmp; + + VPRINTK("ENTER\n"); + + if (ata_id_has_lba(args->id)) { + if (ata_id_has_lba48(args->id)) + n_sectors = ata_id_u64(args->id, 100); + else + n_sectors = ata_id_u32(args->id, 60); + } else { + /* CHS default translation */ + n_sectors = args->id[1] * args->id[3] * args->id[6]; + + if (ata_id_current_chs_valid(args->id)) + /* CHS current translation */ + n_sectors = ata_id_u32(args->id, 57); + } + + n_sectors--; /* ATA TotalUserSectors - 1 */ + + if (args->cmd->cmnd[0] == READ_CAPACITY) { + if( n_sectors >= 0xffffffffULL ) + tmp = 0xffffffff ; /* Return max count on overflow */ + else + tmp = n_sectors ; + + /* sector count, 32-bit */ + rbuf[0] = tmp >> (8 * 3); + rbuf[1] = tmp >> (8 * 2); + rbuf[2] = tmp >> (8 * 1); + rbuf[3] = tmp; + + /* sector size */ + tmp = ATA_SECT_SIZE; + rbuf[6] = tmp >> 8; + rbuf[7] = tmp; + + } else { + /* sector count, 64-bit */ + tmp = n_sectors >> (8 * 4); + rbuf[2] = tmp >> (8 * 3); + rbuf[3] = tmp >> (8 * 2); + rbuf[4] = tmp >> (8 * 1); + rbuf[5] = tmp; + tmp = n_sectors; + rbuf[6] = tmp >> (8 * 3); + rbuf[7] = tmp >> (8 * 2); + rbuf[8] = tmp >> (8 * 1); + rbuf[9] = tmp; + + /* sector size */ + tmp = ATA_SECT_SIZE; + rbuf[12] = tmp >> 8; + rbuf[13] = tmp; + } + + return 0; +} + +/** + * ata_scsiop_report_luns - Simulate REPORT LUNS command + * @args: device IDENTIFY data / SCSI command of interest. + * @rbuf: Response buffer, to which simulated SCSI cmd output is sent. + * @buflen: Response buffer length. + * + * Simulate REPORT LUNS command. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +unsigned int ata_scsiop_report_luns(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen) +{ + VPRINTK("ENTER\n"); + rbuf[3] = 8; /* just one lun, LUN 0, size 8 bytes */ + + return 0; +} + +/** + * ata_scsi_set_sense - Set SCSI sense data and status + * @cmd: SCSI request to be handled + * @sk: SCSI-defined sense key + * @asc: SCSI-defined additional sense code + * @ascq: SCSI-defined additional sense code qualifier + * + * Helper function that builds a valid fixed format, current + * response code and the given sense key (sk), additional sense + * code (asc) and additional sense code qualifier (ascq) with + * a SCSI command status of %SAM_STAT_CHECK_CONDITION and + * DRIVER_SENSE set in the upper bits of scsi_cmnd::result . + * + * LOCKING: + * Not required + */ + +void ata_scsi_set_sense(struct scsi_cmnd *cmd, u8 sk, u8 asc, u8 ascq) +{ + cmd->result = (DRIVER_SENSE << 24) | SAM_STAT_CHECK_CONDITION; + + cmd->sense_buffer[0] = 0x70; /* fixed format, current */ + cmd->sense_buffer[2] = sk; + cmd->sense_buffer[7] = 18 - 8; /* additional sense length */ + cmd->sense_buffer[12] = asc; + cmd->sense_buffer[13] = ascq; +} + +/** + * ata_scsi_badcmd - End a SCSI request with an error + * @cmd: SCSI request to be handled + * @done: SCSI command completion function + * @asc: SCSI-defined additional sense code + * @ascq: SCSI-defined additional sense code qualifier + * + * Helper function that completes a SCSI command with + * %SAM_STAT_CHECK_CONDITION, with a sense key %ILLEGAL_REQUEST + * and the specified additional sense codes. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +void ata_scsi_badcmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *), u8 asc, u8 ascq) +{ + DPRINTK("ENTER\n"); + ata_scsi_set_sense(cmd, ILLEGAL_REQUEST, asc, ascq); + + done(cmd); +} + +static void atapi_sense_complete(struct ata_queued_cmd *qc) +{ + if (qc->err_mask && ((qc->err_mask & AC_ERR_DEV) == 0)) { + /* FIXME: not quite right; we don't want the + * translation of taskfile registers into + * a sense descriptors, since that's only + * correct for ATA, not ATAPI + */ + ata_gen_ata_desc_sense(qc); + } + + qc->scsidone(qc->scsicmd); + ata_qc_free(qc); +} + +/* is it pointless to prefer PIO for "safety reasons"? */ +static inline int ata_pio_use_silly(struct ata_port *ap) +{ + return (ap->flags & ATA_FLAG_PIO_DMA); +} + +static void atapi_request_sense(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct scsi_cmnd *cmd = qc->scsicmd; + + DPRINTK("ATAPI request sense\n"); + + /* FIXME: is this needed? */ + memset(cmd->sense_buffer, 0, sizeof(cmd->sense_buffer)); + + ap->ops->tf_read(ap, &qc->tf); + + /* fill these in, for the case where they are -not- overwritten */ + cmd->sense_buffer[0] = 0x70; + cmd->sense_buffer[2] = qc->tf.feature >> 4; + + ata_qc_reinit(qc); + + ata_sg_init_one(qc, cmd->sense_buffer, sizeof(cmd->sense_buffer)); + qc->dma_dir = DMA_FROM_DEVICE; + + memset(&qc->cdb, 0, qc->dev->cdb_len); + qc->cdb[0] = REQUEST_SENSE; + qc->cdb[4] = SCSI_SENSE_BUFFERSIZE; + + qc->tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + qc->tf.command = ATA_CMD_PACKET; + + if (ata_pio_use_silly(ap)) { + qc->tf.protocol = ATA_PROT_ATAPI_DMA; + qc->tf.feature |= ATAPI_PKT_DMA; + } else { + qc->tf.protocol = ATA_PROT_ATAPI; + qc->tf.lbam = (8 * 1024) & 0xff; + qc->tf.lbah = (8 * 1024) >> 8; + } + qc->nbytes = SCSI_SENSE_BUFFERSIZE; + + qc->complete_fn = atapi_sense_complete; + + ata_qc_issue(qc); + + DPRINTK("EXIT\n"); +} + +static void atapi_qc_complete(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *cmd = qc->scsicmd; + unsigned int err_mask = qc->err_mask; + + VPRINTK("ENTER, err_mask 0x%X\n", err_mask); + + /* handle completion from new EH */ + if (unlikely(qc->ap->ops->error_handler && + (err_mask || qc->flags & ATA_QCFLAG_SENSE_VALID))) { + + if (!(qc->flags & ATA_QCFLAG_SENSE_VALID)) { + /* FIXME: not quite right; we don't want the + * translation of taskfile registers into a + * sense descriptors, since that's only + * correct for ATA, not ATAPI + */ + ata_gen_ata_desc_sense(qc); + } + + /* SCSI EH automatically locks door if sdev->locked is + * set. Sometimes door lock request continues to + * fail, for example, when no media is present. This + * creates a loop - SCSI EH issues door lock which + * fails and gets invoked again to acquire sense data + * for the failed command. + * + * If door lock fails, always clear sdev->locked to + * avoid this infinite loop. + */ + if (qc->cdb[0] == ALLOW_MEDIUM_REMOVAL) + qc->dev->sdev->locked = 0; + + qc->scsicmd->result = SAM_STAT_CHECK_CONDITION; + qc->scsidone(cmd); + ata_qc_free(qc); + return; + } + + /* successful completion or old EH failure path */ + if (unlikely(err_mask & AC_ERR_DEV)) { + cmd->result = SAM_STAT_CHECK_CONDITION; + atapi_request_sense(qc); + return; + } else if (unlikely(err_mask)) { + /* FIXME: not quite right; we don't want the + * translation of taskfile registers into + * a sense descriptors, since that's only + * correct for ATA, not ATAPI + */ + ata_gen_ata_desc_sense(qc); + } else { + u8 *scsicmd = cmd->cmnd; + + if ((scsicmd[0] == INQUIRY) && ((scsicmd[1] & 0x03) == 0)) { + u8 *buf = NULL; + unsigned int buflen; + + buflen = ata_scsi_rbuf_get(cmd, &buf); + + /* ATAPI devices typically report zero for their SCSI version, + * and sometimes deviate from the spec WRT response data + * format. If SCSI version is reported as zero like normal, + * then we make the following fixups: 1) Fake MMC-5 version, + * to indicate to the Linux scsi midlayer this is a modern + * device. 2) Ensure response data format / ATAPI information + * are always correct. + */ + if (buf[2] == 0) { + buf[2] = 0x5; + buf[3] = 0x32; + } + + ata_scsi_rbuf_put(cmd, buf); + } + + cmd->result = SAM_STAT_GOOD; + } + + qc->scsidone(cmd); + ata_qc_free(qc); +} +/** + * atapi_xlat - Initialize PACKET taskfile + * @qc: command structure to be initialized + * @scsicmd: SCSI CDB associated with this PACKET command + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Zero on success, non-zero on failure. + */ + +static unsigned int atapi_xlat(struct ata_queued_cmd *qc, const u8 *scsicmd) +{ + struct scsi_cmnd *cmd = qc->scsicmd; + struct ata_device *dev = qc->dev; + int using_pio = (dev->flags & ATA_DFLAG_PIO); + int nodata = (cmd->sc_data_direction == DMA_NONE); + + if (!using_pio) + /* Check whether ATAPI DMA is safe */ + if (ata_check_atapi_dma(qc)) + using_pio = 1; + + memcpy(&qc->cdb, scsicmd, dev->cdb_len); + + qc->complete_fn = atapi_qc_complete; + + qc->tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE; + if (cmd->sc_data_direction == DMA_TO_DEVICE) { + qc->tf.flags |= ATA_TFLAG_WRITE; + DPRINTK("direction: write\n"); + } + + qc->tf.command = ATA_CMD_PACKET; + + /* no data, or PIO data xfer */ + if (using_pio || nodata) { + if (nodata) + qc->tf.protocol = ATA_PROT_ATAPI_NODATA; + else + qc->tf.protocol = ATA_PROT_ATAPI; + qc->tf.lbam = (8 * 1024) & 0xff; + qc->tf.lbah = (8 * 1024) >> 8; + } + + /* DMA data xfer */ + else { + qc->tf.protocol = ATA_PROT_ATAPI_DMA; + qc->tf.feature |= ATAPI_PKT_DMA; + + if (atapi_dmadir && (cmd->sc_data_direction != DMA_TO_DEVICE)) + /* some SATA bridges need us to indicate data xfer direction */ + qc->tf.feature |= ATAPI_DMADIR; + } + + qc->nbytes = cmd->request_bufflen; + + return 0; +} + +static struct ata_device * ata_find_dev(struct ata_port *ap, int id) +{ + if (likely(id < ATA_MAX_DEVICES)) + return &ap->device[id]; + return NULL; +} + +static struct ata_device * __ata_scsi_find_dev(struct ata_port *ap, + const struct scsi_device *scsidev) +{ + /* skip commands not addressed to targets we simulate */ + if (unlikely(scsidev->channel || scsidev->lun)) + return NULL; + + return ata_find_dev(ap, scsidev->id); +} + +/** + * ata_scsi_dev_enabled - determine if device is enabled + * @dev: ATA device + * + * Determine if commands should be sent to the specified device. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * 0 if commands are not allowed / 1 if commands are allowed + */ + +static int ata_scsi_dev_enabled(struct ata_device *dev) +{ + if (unlikely(!ata_dev_enabled(dev))) + return 0; + + if (!atapi_enabled || (dev->ap->flags & ATA_FLAG_NO_ATAPI)) { + if (unlikely(dev->class == ATA_DEV_ATAPI)) { + ata_dev_printk(dev, KERN_WARNING, + "WARNING: ATAPI is %s, device ignored.\n", + atapi_enabled ? "not supported with this driver" : "disabled"); + return 0; + } + } + + return 1; +} + +/** + * ata_scsi_find_dev - lookup ata_device from scsi_cmnd + * @ap: ATA port to which the device is attached + * @scsidev: SCSI device from which we derive the ATA device + * + * Given various information provided in struct scsi_cmnd, + * map that onto an ATA bus, and using that mapping + * determine which ata_device is associated with the + * SCSI command to be sent. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * Associated ATA device, or %NULL if not found. + */ +static struct ata_device * +ata_scsi_find_dev(struct ata_port *ap, const struct scsi_device *scsidev) +{ + struct ata_device *dev = __ata_scsi_find_dev(ap, scsidev); + + if (unlikely(!dev || !ata_scsi_dev_enabled(dev))) + return NULL; + + return dev; +} + +/* + * ata_scsi_map_proto - Map pass-thru protocol value to taskfile value. + * @byte1: Byte 1 from pass-thru CDB. + * + * RETURNS: + * ATA_PROT_UNKNOWN if mapping failed/unimplemented, protocol otherwise. + */ +static u8 +ata_scsi_map_proto(u8 byte1) +{ + switch((byte1 & 0x1e) >> 1) { + case 3: /* Non-data */ + return ATA_PROT_NODATA; + + case 6: /* DMA */ + return ATA_PROT_DMA; + + case 4: /* PIO Data-in */ + case 5: /* PIO Data-out */ + return ATA_PROT_PIO; + + case 10: /* Device Reset */ + case 0: /* Hard Reset */ + case 1: /* SRST */ + case 2: /* Bus Idle */ + case 7: /* Packet */ + case 8: /* DMA Queued */ + case 9: /* Device Diagnostic */ + case 11: /* UDMA Data-in */ + case 12: /* UDMA Data-Out */ + case 13: /* FPDMA */ + default: /* Reserved */ + break; + } + + return ATA_PROT_UNKNOWN; +} + +/** + * ata_scsi_pass_thru - convert ATA pass-thru CDB to taskfile + * @qc: command structure to be initialized + * @scsicmd: SCSI command to convert + * + * Handles either 12 or 16-byte versions of the CDB. + * + * RETURNS: + * Zero on success, non-zero on failure. + */ +static unsigned int +ata_scsi_pass_thru(struct ata_queued_cmd *qc, const u8 *scsicmd) +{ + struct ata_taskfile *tf = &(qc->tf); + struct scsi_cmnd *cmd = qc->scsicmd; + struct ata_device *dev = qc->dev; + + if ((tf->protocol = ata_scsi_map_proto(scsicmd[1])) == ATA_PROT_UNKNOWN) + goto invalid_fld; + + /* We may not issue DMA commands if no DMA mode is set */ + if (tf->protocol == ATA_PROT_DMA && dev->dma_mode == 0) + goto invalid_fld; + + if (scsicmd[1] & 0xe0) + /* PIO multi not supported yet */ + goto invalid_fld; + + /* + * 12 and 16 byte CDBs use different offsets to + * provide the various register values. + */ + if (scsicmd[0] == ATA_16) { + /* + * 16-byte CDB - may contain extended commands. + * + * If that is the case, copy the upper byte register values. + */ + if (scsicmd[1] & 0x01) { + tf->hob_feature = scsicmd[3]; + tf->hob_nsect = scsicmd[5]; + tf->hob_lbal = scsicmd[7]; + tf->hob_lbam = scsicmd[9]; + tf->hob_lbah = scsicmd[11]; + tf->flags |= ATA_TFLAG_LBA48; + } else + tf->flags &= ~ATA_TFLAG_LBA48; + + /* + * Always copy low byte, device and command registers. + */ + tf->feature = scsicmd[4]; + tf->nsect = scsicmd[6]; + tf->lbal = scsicmd[8]; + tf->lbam = scsicmd[10]; + tf->lbah = scsicmd[12]; + tf->device = scsicmd[13]; + tf->command = scsicmd[14]; + } else { + /* + * 12-byte CDB - incapable of extended commands. + */ + tf->flags &= ~ATA_TFLAG_LBA48; + + tf->feature = scsicmd[3]; + tf->nsect = scsicmd[4]; + tf->lbal = scsicmd[5]; + tf->lbam = scsicmd[6]; + tf->lbah = scsicmd[7]; + tf->device = scsicmd[8]; + tf->command = scsicmd[9]; + } + /* + * If slave is possible, enforce correct master/slave bit + */ + if (qc->ap->flags & ATA_FLAG_SLAVE_POSS) + tf->device = qc->dev->devno ? + tf->device | ATA_DEV1 : tf->device & ~ATA_DEV1; + + /* + * Filter SET_FEATURES - XFER MODE command -- otherwise, + * SET_FEATURES - XFER MODE must be preceded/succeeded + * by an update to hardware-specific registers for each + * controller (i.e. the reason for ->set_piomode(), + * ->set_dmamode(), and ->post_set_mode() hooks). + */ + if ((tf->command == ATA_CMD_SET_FEATURES) + && (tf->feature == SETFEATURES_XFER)) + goto invalid_fld; + + /* + * Set flags so that all registers will be written, + * and pass on write indication (used for PIO/DMA + * setup.) + */ + tf->flags |= (ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE); + + if (cmd->sc_data_direction == DMA_TO_DEVICE) + tf->flags |= ATA_TFLAG_WRITE; + + /* + * Set transfer length. + * + * TODO: find out if we need to do more here to + * cover scatter/gather case. + */ + qc->nsect = cmd->request_bufflen / ATA_SECT_SIZE; + + /* request result TF */ + qc->flags |= ATA_QCFLAG_RESULT_TF; + + return 0; + + invalid_fld: + ata_scsi_set_sense(qc->scsicmd, ILLEGAL_REQUEST, 0x24, 0x00); + /* "Invalid field in cdb" */ + return 1; +} + +/** + * ata_get_xlat_func - check if SCSI to ATA translation is possible + * @dev: ATA device + * @cmd: SCSI command opcode to consider + * + * Look up the SCSI command given, and determine whether the + * SCSI command is to be translated or simulated. + * + * RETURNS: + * Pointer to translation function if possible, %NULL if not. + */ + +static inline ata_xlat_func_t ata_get_xlat_func(struct ata_device *dev, u8 cmd) +{ + switch (cmd) { + case READ_6: + case READ_10: + case READ_16: + + case WRITE_6: + case WRITE_10: + case WRITE_16: + return ata_scsi_rw_xlat; + + case SYNCHRONIZE_CACHE: + if (ata_try_flush_cache(dev)) + return ata_scsi_flush_xlat; + break; + + case VERIFY: + case VERIFY_16: + return ata_scsi_verify_xlat; + + case ATA_12: + case ATA_16: + return ata_scsi_pass_thru; + + case START_STOP: + return ata_scsi_start_stop_xlat; + } + + return NULL; +} + +/** + * ata_scsi_dump_cdb - dump SCSI command contents to dmesg + * @ap: ATA port to which the command was being sent + * @cmd: SCSI command to dump + * + * Prints the contents of a SCSI command via printk(). + */ + +static inline void ata_scsi_dump_cdb(struct ata_port *ap, + struct scsi_cmnd *cmd) +{ +#ifdef ATA_DEBUG + struct scsi_device *scsidev = cmd->device; + u8 *scsicmd = cmd->cmnd; + + DPRINTK("CDB (%u:%d,%d,%d) %02x %02x %02x %02x %02x %02x %02x %02x %02x\n", + ap->id, + scsidev->channel, scsidev->id, scsidev->lun, + scsicmd[0], scsicmd[1], scsicmd[2], scsicmd[3], + scsicmd[4], scsicmd[5], scsicmd[6], scsicmd[7], + scsicmd[8]); +#endif +} + +static inline int __ata_scsi_queuecmd(struct scsi_cmnd *cmd, + void (*done)(struct scsi_cmnd *), + struct ata_device *dev) +{ + int rc = 0; + + if (dev->class == ATA_DEV_ATA) { + ata_xlat_func_t xlat_func = ata_get_xlat_func(dev, + cmd->cmnd[0]); + + if (xlat_func) + rc = ata_scsi_translate(dev, cmd, done, xlat_func); + else + ata_scsi_simulate(dev, cmd, done); + } else + rc = ata_scsi_translate(dev, cmd, done, atapi_xlat); + + return rc; +} + +/** + * ata_scsi_queuecmd - Issue SCSI cdb to libata-managed device + * @cmd: SCSI command to be sent + * @done: Completion function, called when command is complete + * + * In some cases, this function translates SCSI commands into + * ATA taskfiles, and queues the taskfiles to be sent to + * hardware. In other cases, this function simulates a + * SCSI device by evaluating and responding to certain + * SCSI commands. This creates the overall effect of + * ATA and ATAPI devices appearing as SCSI devices. + * + * LOCKING: + * Releases scsi-layer-held lock, and obtains host lock. + * + * RETURNS: + * Return value from __ata_scsi_queuecmd() if @cmd can be queued, + * 0 otherwise. + */ +int ata_scsi_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *)) +{ + struct ata_port *ap; + struct ata_device *dev; + struct scsi_device *scsidev = cmd->device; + struct Scsi_Host *shost = scsidev->host; + int rc = 0; + + ap = ata_shost_to_port(shost); + + spin_unlock(shost->host_lock); + spin_lock(ap->lock); + + ata_scsi_dump_cdb(ap, cmd); + + dev = ata_scsi_find_dev(ap, scsidev); + if (likely(dev)) + rc = __ata_scsi_queuecmd(cmd, done, dev); + else { + cmd->result = (DID_BAD_TARGET << 16); + done(cmd); + } + + spin_unlock(ap->lock); + spin_lock(shost->host_lock); + return rc; +} + +/** + * ata_scsi_simulate - simulate SCSI command on ATA device + * @dev: the target device + * @cmd: SCSI command being sent to device. + * @done: SCSI command completion function. + * + * Interprets and directly executes a select list of SCSI commands + * that can be handled internally. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd, + void (*done)(struct scsi_cmnd *)) +{ + struct ata_scsi_args args; + const u8 *scsicmd = cmd->cmnd; + + args.dev = dev; + args.id = dev->id; + args.cmd = cmd; + args.done = done; + + switch(scsicmd[0]) { + /* no-op's, complete with success */ + case SYNCHRONIZE_CACHE: + case REZERO_UNIT: + case SEEK_6: + case SEEK_10: + case TEST_UNIT_READY: + case FORMAT_UNIT: /* FIXME: correct? */ + case SEND_DIAGNOSTIC: /* FIXME: correct? */ + ata_scsi_rbuf_fill(&args, ata_scsiop_noop); + break; + + case INQUIRY: + if (scsicmd[1] & 2) /* is CmdDt set? */ + ata_scsi_invalid_field(cmd, done); + else if ((scsicmd[1] & 1) == 0) /* is EVPD clear? */ + ata_scsi_rbuf_fill(&args, ata_scsiop_inq_std); + else if (scsicmd[2] == 0x00) + ata_scsi_rbuf_fill(&args, ata_scsiop_inq_00); + else if (scsicmd[2] == 0x80) + ata_scsi_rbuf_fill(&args, ata_scsiop_inq_80); + else if (scsicmd[2] == 0x83) + ata_scsi_rbuf_fill(&args, ata_scsiop_inq_83); + else + ata_scsi_invalid_field(cmd, done); + break; + + case MODE_SENSE: + case MODE_SENSE_10: + ata_scsi_rbuf_fill(&args, ata_scsiop_mode_sense); + break; + + case MODE_SELECT: /* unconditionally return */ + case MODE_SELECT_10: /* bad-field-in-cdb */ + ata_scsi_invalid_field(cmd, done); + break; + + case READ_CAPACITY: + ata_scsi_rbuf_fill(&args, ata_scsiop_read_cap); + break; + + case SERVICE_ACTION_IN: + if ((scsicmd[1] & 0x1f) == SAI_READ_CAPACITY_16) + ata_scsi_rbuf_fill(&args, ata_scsiop_read_cap); + else + ata_scsi_invalid_field(cmd, done); + break; + + case REPORT_LUNS: + ata_scsi_rbuf_fill(&args, ata_scsiop_report_luns); + break; + + /* mandatory commands we haven't implemented yet */ + case REQUEST_SENSE: + + /* all other commands */ + default: + ata_scsi_set_sense(cmd, ILLEGAL_REQUEST, 0x20, 0x0); + /* "Invalid command operation code" */ + done(cmd); + break; + } +} + +void ata_scsi_scan_host(struct ata_port *ap) +{ + unsigned int i; + + if (ap->flags & ATA_FLAG_DISABLED) + return; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + struct scsi_device *sdev; + + if (!ata_dev_enabled(dev) || dev->sdev) + continue; + + sdev = __scsi_add_device(ap->scsi_host, 0, i, 0, NULL); + if (!IS_ERR(sdev)) { + dev->sdev = sdev; + scsi_device_put(sdev); + } + } +} + +/** + * ata_scsi_offline_dev - offline attached SCSI device + * @dev: ATA device to offline attached SCSI device for + * + * This function is called from ata_eh_hotplug() and responsible + * for taking the SCSI device attached to @dev offline. This + * function is called with host lock which protects dev->sdev + * against clearing. + * + * LOCKING: + * spin_lock_irqsave(host lock) + * + * RETURNS: + * 1 if attached SCSI device exists, 0 otherwise. + */ +int ata_scsi_offline_dev(struct ata_device *dev) +{ + if (dev->sdev) { + scsi_device_set_state(dev->sdev, SDEV_OFFLINE); + return 1; + } + return 0; +} + +/** + * ata_scsi_remove_dev - remove attached SCSI device + * @dev: ATA device to remove attached SCSI device for + * + * This function is called from ata_eh_scsi_hotplug() and + * responsible for removing the SCSI device attached to @dev. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +static void ata_scsi_remove_dev(struct ata_device *dev) +{ + struct ata_port *ap = dev->ap; + struct scsi_device *sdev; + unsigned long flags; + + /* Alas, we need to grab scan_mutex to ensure SCSI device + * state doesn't change underneath us and thus + * scsi_device_get() always succeeds. The mutex locking can + * be removed if there is __scsi_device_get() interface which + * increments reference counts regardless of device state. + */ + mutex_lock(&ap->scsi_host->scan_mutex); + spin_lock_irqsave(ap->lock, flags); + + /* clearing dev->sdev is protected by host lock */ + sdev = dev->sdev; + dev->sdev = NULL; + + if (sdev) { + /* If user initiated unplug races with us, sdev can go + * away underneath us after the host lock and + * scan_mutex are released. Hold onto it. + */ + if (scsi_device_get(sdev) == 0) { + /* The following ensures the attached sdev is + * offline on return from ata_scsi_offline_dev() + * regardless it wins or loses the race + * against this function. + */ + scsi_device_set_state(sdev, SDEV_OFFLINE); + } else { + WARN_ON(1); + sdev = NULL; + } + } + + spin_unlock_irqrestore(ap->lock, flags); + mutex_unlock(&ap->scsi_host->scan_mutex); + + if (sdev) { + ata_dev_printk(dev, KERN_INFO, "detaching (SCSI %s)\n", + sdev->sdev_gendev.bus_id); + + scsi_remove_device(sdev); + scsi_device_put(sdev); + } +} + +/** + * ata_scsi_hotplug - SCSI part of hotplug + * @data: Pointer to ATA port to perform SCSI hotplug on + * + * Perform SCSI part of hotplug. It's executed from a separate + * workqueue after EH completes. This is necessary because SCSI + * hot plugging requires working EH and hot unplugging is + * synchronized with hot plugging with a mutex. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +void ata_scsi_hotplug(void *data) +{ + struct ata_port *ap = data; + int i; + + if (ap->pflags & ATA_PFLAG_UNLOADING) { + DPRINTK("ENTER/EXIT - unloading\n"); + return; + } + + DPRINTK("ENTER\n"); + + /* unplug detached devices */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + unsigned long flags; + + if (!(dev->flags & ATA_DFLAG_DETACHED)) + continue; + + spin_lock_irqsave(ap->lock, flags); + dev->flags &= ~ATA_DFLAG_DETACHED; + spin_unlock_irqrestore(ap->lock, flags); + + ata_scsi_remove_dev(dev); + } + + /* scan for new ones */ + ata_scsi_scan_host(ap); + + /* If we scanned while EH was in progress, scan would have + * failed silently. Requeue if there are enabled but + * unattached devices. + */ + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + if (ata_dev_enabled(dev) && !dev->sdev) { + queue_delayed_work(ata_aux_wq, &ap->hotplug_task, HZ); + break; + } + } + + DPRINTK("EXIT\n"); +} + +/** + * ata_scsi_user_scan - indication for user-initiated bus scan + * @shost: SCSI host to scan + * @channel: Channel to scan + * @id: ID to scan + * @lun: LUN to scan + * + * This function is called when user explicitly requests bus + * scan. Set probe pending flag and invoke EH. + * + * LOCKING: + * SCSI layer (we don't care) + * + * RETURNS: + * Zero. + */ +static int ata_scsi_user_scan(struct Scsi_Host *shost, unsigned int channel, + unsigned int id, unsigned int lun) +{ + struct ata_port *ap = ata_shost_to_port(shost); + unsigned long flags; + int rc = 0; + + if (!ap->ops->error_handler) + return -EOPNOTSUPP; + + if ((channel != SCAN_WILD_CARD && channel != 0) || + (lun != SCAN_WILD_CARD && lun != 0)) + return -EINVAL; + + spin_lock_irqsave(ap->lock, flags); + + if (id == SCAN_WILD_CARD) { + ap->eh_info.probe_mask |= (1 << ATA_MAX_DEVICES) - 1; + ap->eh_info.action |= ATA_EH_SOFTRESET; + } else { + struct ata_device *dev = ata_find_dev(ap, id); + + if (dev) { + ap->eh_info.probe_mask |= 1 << dev->devno; + ap->eh_info.action |= ATA_EH_SOFTRESET; + ap->eh_info.flags |= ATA_EHI_RESUME_LINK; + } else + rc = -EINVAL; + } + + if (rc == 0) + ata_port_schedule_eh(ap); + + spin_unlock_irqrestore(ap->lock, flags); + + return rc; +} + +/** + * ata_scsi_dev_rescan - initiate scsi_rescan_device() + * @data: Pointer to ATA port to perform scsi_rescan_device() + * + * After ATA pass thru (SAT) commands are executed successfully, + * libata need to propagate the changes to SCSI layer. This + * function must be executed from ata_aux_wq such that sdev + * attach/detach don't race with rescan. + * + * LOCKING: + * Kernel thread context (may sleep). + */ +void ata_scsi_dev_rescan(void *data) +{ + struct ata_port *ap = data; + struct ata_device *dev; + unsigned int i; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + dev = &ap->device[i]; + + if (ata_dev_enabled(dev) && dev->sdev) + scsi_rescan_device(&(dev->sdev->sdev_gendev)); + } +} + +/** + * ata_sas_port_alloc - Allocate port for a SAS attached SATA device + * @pdev: PCI device that the scsi device is attached to + * @port_info: Information from low-level host driver + * @shost: SCSI host that the scsi device is attached to + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * ata_port pointer on success / NULL on failure. + */ + +struct ata_port *ata_sas_port_alloc(struct ata_host *host, + struct ata_port_info *port_info, + struct Scsi_Host *shost) +{ + struct ata_port *ap = kzalloc(sizeof(*ap), GFP_KERNEL); + struct ata_probe_ent *ent; + + if (!ap) + return NULL; + + ent = ata_probe_ent_alloc(host->dev, port_info); + if (!ent) { + kfree(ap); + return NULL; + } + + ata_port_init(ap, host, ent, 0); + ap->lock = shost->host_lock; + kfree(ent); + return ap; +} +EXPORT_SYMBOL_GPL(ata_sas_port_alloc); + +/** + * ata_sas_port_start - Set port up for dma. + * @ap: Port to initialize + * + * Called just after data structures for each port are + * initialized. Allocates DMA pad. + * + * May be used as the port_start() entry in ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ +int ata_sas_port_start(struct ata_port *ap) +{ + return ata_pad_alloc(ap, ap->dev); +} +EXPORT_SYMBOL_GPL(ata_sas_port_start); + +/** + * ata_port_stop - Undo ata_sas_port_start() + * @ap: Port to shut down + * + * Frees the DMA pad. + * + * May be used as the port_stop() entry in ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ + +void ata_sas_port_stop(struct ata_port *ap) +{ + ata_pad_free(ap, ap->dev); +} +EXPORT_SYMBOL_GPL(ata_sas_port_stop); + +/** + * ata_sas_port_init - Initialize a SATA device + * @ap: SATA port to initialize + * + * LOCKING: + * PCI/etc. bus probe sem. + * + * RETURNS: + * Zero on success, non-zero on error. + */ + +int ata_sas_port_init(struct ata_port *ap) +{ + int rc = ap->ops->port_start(ap); + + if (!rc) + rc = ata_bus_probe(ap); + + return rc; +} +EXPORT_SYMBOL_GPL(ata_sas_port_init); + +/** + * ata_sas_port_destroy - Destroy a SATA port allocated by ata_sas_port_alloc + * @ap: SATA port to destroy + * + */ + +void ata_sas_port_destroy(struct ata_port *ap) +{ + ap->ops->port_stop(ap); + kfree(ap); +} +EXPORT_SYMBOL_GPL(ata_sas_port_destroy); + +/** + * ata_sas_slave_configure - Default slave_config routine for libata devices + * @sdev: SCSI device to configure + * @ap: ATA port to which SCSI device is attached + * + * RETURNS: + * Zero. + */ + +int ata_sas_slave_configure(struct scsi_device *sdev, struct ata_port *ap) +{ + ata_scsi_sdev_config(sdev); + ata_scsi_dev_config(sdev, ap->device); + return 0; +} +EXPORT_SYMBOL_GPL(ata_sas_slave_configure); + +/** + * ata_sas_queuecmd - Issue SCSI cdb to libata-managed device + * @cmd: SCSI command to be sent + * @done: Completion function, called when command is complete + * @ap: ATA port to which the command is being sent + * + * RETURNS: + * Zero. + */ + +int ata_sas_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *), + struct ata_port *ap) +{ + ata_scsi_dump_cdb(ap, cmd); + + if (likely(ata_scsi_dev_enabled(ap->device))) + __ata_scsi_queuecmd(cmd, done, ap->device); + else { + cmd->result = (DID_BAD_TARGET << 16); + done(cmd); + } + return 0; +} +EXPORT_SYMBOL_GPL(ata_sas_queuecmd); diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c new file mode 100644 index 00000000000..08b3a407473 --- /dev/null +++ b/drivers/ata/libata-sff.c @@ -0,0 +1,1121 @@ +/* + * libata-bmdma.c - helper library for PCI IDE BMDMA + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2003-2006 Red Hat, Inc. All rights reserved. + * Copyright 2003-2006 Jeff Garzik + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available from http://www.t13.org/ and + * http://www.sata-io.org/ + * + */ + +#include <linux/kernel.h> +#include <linux/pci.h> +#include <linux/libata.h> + +#include "libata.h" + +/** + * ata_tf_load_pio - send taskfile registers to host controller + * @ap: Port to which output is sent + * @tf: ATA taskfile register set + * + * Outputs ATA taskfile to standard ATA host controller. + * + * LOCKING: + * Inherited from caller. + */ + +static void ata_tf_load_pio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; + + if (tf->ctl != ap->last_ctl) { + outb(tf->ctl, ioaddr->ctl_addr); + ap->last_ctl = tf->ctl; + ata_wait_idle(ap); + } + + if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { + outb(tf->hob_feature, ioaddr->feature_addr); + outb(tf->hob_nsect, ioaddr->nsect_addr); + outb(tf->hob_lbal, ioaddr->lbal_addr); + outb(tf->hob_lbam, ioaddr->lbam_addr); + outb(tf->hob_lbah, ioaddr->lbah_addr); + VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n", + tf->hob_feature, + tf->hob_nsect, + tf->hob_lbal, + tf->hob_lbam, + tf->hob_lbah); + } + + if (is_addr) { + outb(tf->feature, ioaddr->feature_addr); + outb(tf->nsect, ioaddr->nsect_addr); + outb(tf->lbal, ioaddr->lbal_addr); + outb(tf->lbam, ioaddr->lbam_addr); + outb(tf->lbah, ioaddr->lbah_addr); + VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n", + tf->feature, + tf->nsect, + tf->lbal, + tf->lbam, + tf->lbah); + } + + if (tf->flags & ATA_TFLAG_DEVICE) { + outb(tf->device, ioaddr->device_addr); + VPRINTK("device 0x%X\n", tf->device); + } + + ata_wait_idle(ap); +} + +/** + * ata_tf_load_mmio - send taskfile registers to host controller + * @ap: Port to which output is sent + * @tf: ATA taskfile register set + * + * Outputs ATA taskfile to standard ATA host controller using MMIO. + * + * LOCKING: + * Inherited from caller. + */ + +static void ata_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; + + if (tf->ctl != ap->last_ctl) { + writeb(tf->ctl, (void __iomem *) ap->ioaddr.ctl_addr); + ap->last_ctl = tf->ctl; + ata_wait_idle(ap); + } + + if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { + writeb(tf->hob_feature, (void __iomem *) ioaddr->feature_addr); + writeb(tf->hob_nsect, (void __iomem *) ioaddr->nsect_addr); + writeb(tf->hob_lbal, (void __iomem *) ioaddr->lbal_addr); + writeb(tf->hob_lbam, (void __iomem *) ioaddr->lbam_addr); + writeb(tf->hob_lbah, (void __iomem *) ioaddr->lbah_addr); + VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n", + tf->hob_feature, + tf->hob_nsect, + tf->hob_lbal, + tf->hob_lbam, + tf->hob_lbah); + } + + if (is_addr) { + writeb(tf->feature, (void __iomem *) ioaddr->feature_addr); + writeb(tf->nsect, (void __iomem *) ioaddr->nsect_addr); + writeb(tf->lbal, (void __iomem *) ioaddr->lbal_addr); + writeb(tf->lbam, (void __iomem *) ioaddr->lbam_addr); + writeb(tf->lbah, (void __iomem *) ioaddr->lbah_addr); + VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n", + tf->feature, + tf->nsect, + tf->lbal, + tf->lbam, + tf->lbah); + } + + if (tf->flags & ATA_TFLAG_DEVICE) { + writeb(tf->device, (void __iomem *) ioaddr->device_addr); + VPRINTK("device 0x%X\n", tf->device); + } + + ata_wait_idle(ap); +} + + +/** + * ata_tf_load - send taskfile registers to host controller + * @ap: Port to which output is sent + * @tf: ATA taskfile register set + * + * Outputs ATA taskfile to standard ATA host controller using MMIO + * or PIO as indicated by the ATA_FLAG_MMIO flag. + * Writes the control, feature, nsect, lbal, lbam, and lbah registers. + * Optionally (ATA_TFLAG_LBA48) writes hob_feature, hob_nsect, + * hob_lbal, hob_lbam, and hob_lbah. + * + * This function waits for idle (!BUSY and !DRQ) after writing + * registers. If the control register has a new value, this + * function also waits for idle after writing control and before + * writing the remaining registers. + * + * May be used as the tf_load() entry in ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ +void ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) +{ + if (ap->flags & ATA_FLAG_MMIO) + ata_tf_load_mmio(ap, tf); + else + ata_tf_load_pio(ap, tf); +} + +/** + * ata_exec_command_pio - issue ATA command to host controller + * @ap: port to which command is being issued + * @tf: ATA taskfile register set + * + * Issues PIO write to ATA command register, with proper + * synchronization with interrupt handler / other threads. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void ata_exec_command_pio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + DPRINTK("ata%u: cmd 0x%X\n", ap->id, tf->command); + + outb(tf->command, ap->ioaddr.command_addr); + ata_pause(ap); +} + + +/** + * ata_exec_command_mmio - issue ATA command to host controller + * @ap: port to which command is being issued + * @tf: ATA taskfile register set + * + * Issues MMIO write to ATA command register, with proper + * synchronization with interrupt handler / other threads. + * + * FIXME: missing write posting for 400nS delay enforcement + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void ata_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + DPRINTK("ata%u: cmd 0x%X\n", ap->id, tf->command); + + writeb(tf->command, (void __iomem *) ap->ioaddr.command_addr); + ata_pause(ap); +} + + +/** + * ata_exec_command - issue ATA command to host controller + * @ap: port to which command is being issued + * @tf: ATA taskfile register set + * + * Issues PIO/MMIO write to ATA command register, with proper + * synchronization with interrupt handler / other threads. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_exec_command(struct ata_port *ap, const struct ata_taskfile *tf) +{ + if (ap->flags & ATA_FLAG_MMIO) + ata_exec_command_mmio(ap, tf); + else + ata_exec_command_pio(ap, tf); +} + +/** + * ata_tf_read_pio - input device's ATA taskfile shadow registers + * @ap: Port from which input is read + * @tf: ATA taskfile register set for storing input + * + * Reads ATA taskfile registers for currently-selected device + * into @tf. + * + * LOCKING: + * Inherited from caller. + */ + +static void ata_tf_read_pio(struct ata_port *ap, struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + + tf->command = ata_check_status(ap); + tf->feature = inb(ioaddr->error_addr); + tf->nsect = inb(ioaddr->nsect_addr); + tf->lbal = inb(ioaddr->lbal_addr); + tf->lbam = inb(ioaddr->lbam_addr); + tf->lbah = inb(ioaddr->lbah_addr); + tf->device = inb(ioaddr->device_addr); + + if (tf->flags & ATA_TFLAG_LBA48) { + outb(tf->ctl | ATA_HOB, ioaddr->ctl_addr); + tf->hob_feature = inb(ioaddr->error_addr); + tf->hob_nsect = inb(ioaddr->nsect_addr); + tf->hob_lbal = inb(ioaddr->lbal_addr); + tf->hob_lbam = inb(ioaddr->lbam_addr); + tf->hob_lbah = inb(ioaddr->lbah_addr); + } +} + +/** + * ata_tf_read_mmio - input device's ATA taskfile shadow registers + * @ap: Port from which input is read + * @tf: ATA taskfile register set for storing input + * + * Reads ATA taskfile registers for currently-selected device + * into @tf via MMIO. + * + * LOCKING: + * Inherited from caller. + */ + +static void ata_tf_read_mmio(struct ata_port *ap, struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + + tf->command = ata_check_status(ap); + tf->feature = readb((void __iomem *)ioaddr->error_addr); + tf->nsect = readb((void __iomem *)ioaddr->nsect_addr); + tf->lbal = readb((void __iomem *)ioaddr->lbal_addr); + tf->lbam = readb((void __iomem *)ioaddr->lbam_addr); + tf->lbah = readb((void __iomem *)ioaddr->lbah_addr); + tf->device = readb((void __iomem *)ioaddr->device_addr); + + if (tf->flags & ATA_TFLAG_LBA48) { + writeb(tf->ctl | ATA_HOB, (void __iomem *) ap->ioaddr.ctl_addr); + tf->hob_feature = readb((void __iomem *)ioaddr->error_addr); + tf->hob_nsect = readb((void __iomem *)ioaddr->nsect_addr); + tf->hob_lbal = readb((void __iomem *)ioaddr->lbal_addr); + tf->hob_lbam = readb((void __iomem *)ioaddr->lbam_addr); + tf->hob_lbah = readb((void __iomem *)ioaddr->lbah_addr); + } +} + + +/** + * ata_tf_read - input device's ATA taskfile shadow registers + * @ap: Port from which input is read + * @tf: ATA taskfile register set for storing input + * + * Reads ATA taskfile registers for currently-selected device + * into @tf. + * + * Reads nsect, lbal, lbam, lbah, and device. If ATA_TFLAG_LBA48 + * is set, also reads the hob registers. + * + * May be used as the tf_read() entry in ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ +void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf) +{ + if (ap->flags & ATA_FLAG_MMIO) + ata_tf_read_mmio(ap, tf); + else + ata_tf_read_pio(ap, tf); +} + +/** + * ata_check_status_pio - Read device status reg & clear interrupt + * @ap: port where the device is + * + * Reads ATA taskfile status register for currently-selected device + * and return its value. This also clears pending interrupts + * from this device + * + * LOCKING: + * Inherited from caller. + */ +static u8 ata_check_status_pio(struct ata_port *ap) +{ + return inb(ap->ioaddr.status_addr); +} + +/** + * ata_check_status_mmio - Read device status reg & clear interrupt + * @ap: port where the device is + * + * Reads ATA taskfile status register for currently-selected device + * via MMIO and return its value. This also clears pending interrupts + * from this device + * + * LOCKING: + * Inherited from caller. + */ +static u8 ata_check_status_mmio(struct ata_port *ap) +{ + return readb((void __iomem *) ap->ioaddr.status_addr); +} + + +/** + * ata_check_status - Read device status reg & clear interrupt + * @ap: port where the device is + * + * Reads ATA taskfile status register for currently-selected device + * and return its value. This also clears pending interrupts + * from this device + * + * May be used as the check_status() entry in ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ +u8 ata_check_status(struct ata_port *ap) +{ + if (ap->flags & ATA_FLAG_MMIO) + return ata_check_status_mmio(ap); + return ata_check_status_pio(ap); +} + + +/** + * ata_altstatus - Read device alternate status reg + * @ap: port where the device is + * + * Reads ATA taskfile alternate status register for + * currently-selected device and return its value. + * + * Note: may NOT be used as the check_altstatus() entry in + * ata_port_operations. + * + * LOCKING: + * Inherited from caller. + */ +u8 ata_altstatus(struct ata_port *ap) +{ + if (ap->ops->check_altstatus) + return ap->ops->check_altstatus(ap); + + if (ap->flags & ATA_FLAG_MMIO) + return readb((void __iomem *)ap->ioaddr.altstatus_addr); + return inb(ap->ioaddr.altstatus_addr); +} + +/** + * ata_bmdma_setup_mmio - Set up PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void ata_bmdma_setup_mmio (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u8 dmactl; + void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr; + + /* load PRD table addr. */ + mb(); /* make sure PRD table writes are visible to controller */ + writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS); + + /* specify data direction, triple-check start bit is clear */ + dmactl = readb(mmio + ATA_DMA_CMD); + dmactl &= ~(ATA_DMA_WR | ATA_DMA_START); + if (!rw) + dmactl |= ATA_DMA_WR; + writeb(dmactl, mmio + ATA_DMA_CMD); + + /* issue r/w command */ + ap->ops->exec_command(ap, &qc->tf); +} + +/** + * ata_bmdma_start_mmio - Start a PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void ata_bmdma_start_mmio (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr; + u8 dmactl; + + /* start host DMA transaction */ + dmactl = readb(mmio + ATA_DMA_CMD); + writeb(dmactl | ATA_DMA_START, mmio + ATA_DMA_CMD); + + /* Strictly, one may wish to issue a readb() here, to + * flush the mmio write. However, control also passes + * to the hardware at this point, and it will interrupt + * us when we are to resume control. So, in effect, + * we don't care when the mmio write flushes. + * Further, a read of the DMA status register _immediately_ + * following the write may not be what certain flaky hardware + * is expected, so I think it is best to not add a readb() + * without first all the MMIO ATA cards/mobos. + * Or maybe I'm just being paranoid. + */ +} + +/** + * ata_bmdma_setup_pio - Set up PCI IDE BMDMA transaction (PIO) + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void ata_bmdma_setup_pio (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u8 dmactl; + + /* load PRD table addr. */ + outl(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS); + + /* specify data direction, triple-check start bit is clear */ + dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + dmactl &= ~(ATA_DMA_WR | ATA_DMA_START); + if (!rw) + dmactl |= ATA_DMA_WR; + outb(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + + /* issue r/w command */ + ap->ops->exec_command(ap, &qc->tf); +} + +/** + * ata_bmdma_start_pio - Start a PCI IDE BMDMA transaction (PIO) + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void ata_bmdma_start_pio (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + u8 dmactl; + + /* start host DMA transaction */ + dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + outb(dmactl | ATA_DMA_START, + ap->ioaddr.bmdma_addr + ATA_DMA_CMD); +} + + +/** + * ata_bmdma_start - Start a PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * Writes the ATA_DMA_START flag to the DMA command register. + * + * May be used as the bmdma_start() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_bmdma_start(struct ata_queued_cmd *qc) +{ + if (qc->ap->flags & ATA_FLAG_MMIO) + ata_bmdma_start_mmio(qc); + else + ata_bmdma_start_pio(qc); +} + + +/** + * ata_bmdma_setup - Set up PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * Writes address of PRD table to device's PRD Table Address + * register, sets the DMA control register, and calls + * ops->exec_command() to start the transfer. + * + * May be used as the bmdma_setup() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ +void ata_bmdma_setup(struct ata_queued_cmd *qc) +{ + if (qc->ap->flags & ATA_FLAG_MMIO) + ata_bmdma_setup_mmio(qc); + else + ata_bmdma_setup_pio(qc); +} + + +/** + * ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt. + * @ap: Port associated with this ATA transaction. + * + * Clear interrupt and error flags in DMA status register. + * + * May be used as the irq_clear() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +void ata_bmdma_irq_clear(struct ata_port *ap) +{ + if (!ap->ioaddr.bmdma_addr) + return; + + if (ap->flags & ATA_FLAG_MMIO) { + void __iomem *mmio = + ((void __iomem *) ap->ioaddr.bmdma_addr) + ATA_DMA_STATUS; + writeb(readb(mmio), mmio); + } else { + unsigned long addr = ap->ioaddr.bmdma_addr + ATA_DMA_STATUS; + outb(inb(addr), addr); + } +} + + +/** + * ata_bmdma_status - Read PCI IDE BMDMA status + * @ap: Port associated with this ATA transaction. + * + * Read and return BMDMA status register. + * + * May be used as the bmdma_status() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +u8 ata_bmdma_status(struct ata_port *ap) +{ + u8 host_stat; + if (ap->flags & ATA_FLAG_MMIO) { + void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr; + host_stat = readb(mmio + ATA_DMA_STATUS); + } else + host_stat = inb(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); + return host_stat; +} + + +/** + * ata_bmdma_stop - Stop PCI IDE BMDMA transfer + * @qc: Command we are ending DMA for + * + * Clears the ATA_DMA_START flag in the dma control register + * + * May be used as the bmdma_stop() entry in ata_port_operations. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +void ata_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + if (ap->flags & ATA_FLAG_MMIO) { + void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr; + + /* clear start/stop bit */ + writeb(readb(mmio + ATA_DMA_CMD) & ~ATA_DMA_START, + mmio + ATA_DMA_CMD); + } else { + /* clear start/stop bit */ + outb(inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD) & ~ATA_DMA_START, + ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + } + + /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */ + ata_altstatus(ap); /* dummy read */ +} + +/** + * ata_bmdma_freeze - Freeze BMDMA controller port + * @ap: port to freeze + * + * Freeze BMDMA controller port. + * + * LOCKING: + * Inherited from caller. + */ +void ata_bmdma_freeze(struct ata_port *ap) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + + ap->ctl |= ATA_NIEN; + ap->last_ctl = ap->ctl; + + if (ap->flags & ATA_FLAG_MMIO) + writeb(ap->ctl, (void __iomem *)ioaddr->ctl_addr); + else + outb(ap->ctl, ioaddr->ctl_addr); +} + +/** + * ata_bmdma_thaw - Thaw BMDMA controller port + * @ap: port to thaw + * + * Thaw BMDMA controller port. + * + * LOCKING: + * Inherited from caller. + */ +void ata_bmdma_thaw(struct ata_port *ap) +{ + /* clear & re-enable interrupts */ + ata_chk_status(ap); + ap->ops->irq_clear(ap); + if (ap->ioaddr.ctl_addr) /* FIXME: hack. create a hook instead */ + ata_irq_on(ap); +} + +/** + * ata_bmdma_drive_eh - Perform EH with given methods for BMDMA controller + * @ap: port to handle error for + * @prereset: prereset method (can be NULL) + * @softreset: softreset method (can be NULL) + * @hardreset: hardreset method (can be NULL) + * @postreset: postreset method (can be NULL) + * + * Handle error for ATA BMDMA controller. It can handle both + * PATA and SATA controllers. Many controllers should be able to + * use this EH as-is or with some added handling before and + * after. + * + * This function is intended to be used for constructing + * ->error_handler callback by low level drivers. + * + * LOCKING: + * Kernel thread context (may sleep) + */ +void ata_bmdma_drive_eh(struct ata_port *ap, ata_prereset_fn_t prereset, + ata_reset_fn_t softreset, ata_reset_fn_t hardreset, + ata_postreset_fn_t postreset) +{ + struct ata_eh_context *ehc = &ap->eh_context; + struct ata_queued_cmd *qc; + unsigned long flags; + int thaw = 0; + + qc = __ata_qc_from_tag(ap, ap->active_tag); + if (qc && !(qc->flags & ATA_QCFLAG_FAILED)) + qc = NULL; + + /* reset PIO HSM and stop DMA engine */ + spin_lock_irqsave(ap->lock, flags); + + ap->hsm_task_state = HSM_ST_IDLE; + + if (qc && (qc->tf.protocol == ATA_PROT_DMA || + qc->tf.protocol == ATA_PROT_ATAPI_DMA)) { + u8 host_stat; + + host_stat = ata_bmdma_status(ap); + + ata_ehi_push_desc(&ehc->i, "BMDMA stat 0x%x", host_stat); + + /* BMDMA controllers indicate host bus error by + * setting DMA_ERR bit and timing out. As it wasn't + * really a timeout event, adjust error mask and + * cancel frozen state. + */ + if (qc->err_mask == AC_ERR_TIMEOUT && host_stat & ATA_DMA_ERR) { + qc->err_mask = AC_ERR_HOST_BUS; + thaw = 1; + } + + ap->ops->bmdma_stop(qc); + } + + ata_altstatus(ap); + ata_chk_status(ap); + ap->ops->irq_clear(ap); + + spin_unlock_irqrestore(ap->lock, flags); + + if (thaw) + ata_eh_thaw_port(ap); + + /* PIO and DMA engines have been stopped, perform recovery */ + ata_do_eh(ap, prereset, softreset, hardreset, postreset); +} + +/** + * ata_bmdma_error_handler - Stock error handler for BMDMA controller + * @ap: port to handle error for + * + * Stock error handler for BMDMA controller. + * + * LOCKING: + * Kernel thread context (may sleep) + */ +void ata_bmdma_error_handler(struct ata_port *ap) +{ + ata_reset_fn_t hardreset; + + hardreset = NULL; + if (sata_scr_valid(ap)) + hardreset = sata_std_hardreset; + + ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, hardreset, + ata_std_postreset); +} + +/** + * ata_bmdma_post_internal_cmd - Stock post_internal_cmd for + * BMDMA controller + * @qc: internal command to clean up + * + * LOCKING: + * Kernel thread context (may sleep) + */ +void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc) +{ + ata_bmdma_stop(qc); +} + +#ifdef CONFIG_PCI +/** + * ata_pci_init_native_mode - Initialize native-mode driver + * @pdev: pci device to be initialized + * @port: array[2] of pointers to port info structures. + * @ports: bitmap of ports present + * + * Utility function which allocates and initializes an + * ata_probe_ent structure for a standard dual-port + * PIO-based IDE controller. The returned ata_probe_ent + * structure can be passed to ata_device_add(). The returned + * ata_probe_ent structure should then be freed with kfree(). + * + * The caller need only pass the address of the primary port, the + * secondary will be deduced automatically. If the device has non + * standard secondary port mappings this function can be called twice, + * once for each interface. + */ + +struct ata_probe_ent * +ata_pci_init_native_mode(struct pci_dev *pdev, struct ata_port_info **port, int ports) +{ + struct ata_probe_ent *probe_ent = + ata_probe_ent_alloc(pci_dev_to_dev(pdev), port[0]); + int p = 0; + unsigned long bmdma; + + if (!probe_ent) + return NULL; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->private_data = port[0]->private_data; + + if (ports & ATA_PORT_PRIMARY) { + probe_ent->port[p].cmd_addr = pci_resource_start(pdev, 0); + probe_ent->port[p].altstatus_addr = + probe_ent->port[p].ctl_addr = + pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS; + bmdma = pci_resource_start(pdev, 4); + if (bmdma) { + if (inb(bmdma + 2) & 0x80) + probe_ent->_host_flags |= ATA_HOST_SIMPLEX; + probe_ent->port[p].bmdma_addr = bmdma; + } + ata_std_ports(&probe_ent->port[p]); + p++; + } + + if (ports & ATA_PORT_SECONDARY) { + probe_ent->port[p].cmd_addr = pci_resource_start(pdev, 2); + probe_ent->port[p].altstatus_addr = + probe_ent->port[p].ctl_addr = + pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS; + bmdma = pci_resource_start(pdev, 4); + if (bmdma) { + bmdma += 8; + if(inb(bmdma + 2) & 0x80) + probe_ent->_host_flags |= ATA_HOST_SIMPLEX; + probe_ent->port[p].bmdma_addr = bmdma; + } + ata_std_ports(&probe_ent->port[p]); + probe_ent->pinfo2 = port[1]; + p++; + } + + probe_ent->n_ports = p; + return probe_ent; +} + + +static struct ata_probe_ent *ata_pci_init_legacy_port(struct pci_dev *pdev, + struct ata_port_info **port, int port_mask) +{ + struct ata_probe_ent *probe_ent; + unsigned long bmdma = pci_resource_start(pdev, 4); + + probe_ent = ata_probe_ent_alloc(pci_dev_to_dev(pdev), port[0]); + if (!probe_ent) + return NULL; + + probe_ent->n_ports = 2; + probe_ent->private_data = port[0]->private_data; + + if (port_mask & ATA_PORT_PRIMARY) { + probe_ent->irq = ATA_PRIMARY_IRQ; + probe_ent->port[0].cmd_addr = ATA_PRIMARY_CMD; + probe_ent->port[0].altstatus_addr = + probe_ent->port[0].ctl_addr = ATA_PRIMARY_CTL; + if (bmdma) { + probe_ent->port[0].bmdma_addr = bmdma; + if (inb(bmdma + 2) & 0x80) + probe_ent->_host_flags |= ATA_HOST_SIMPLEX; + } + ata_std_ports(&probe_ent->port[0]); + } else + probe_ent->dummy_port_mask |= ATA_PORT_PRIMARY; + + if (port_mask & ATA_PORT_SECONDARY) { + if (probe_ent->irq) + probe_ent->irq2 = ATA_SECONDARY_IRQ; + else + probe_ent->irq = ATA_SECONDARY_IRQ; + probe_ent->port[1].cmd_addr = ATA_SECONDARY_CMD; + probe_ent->port[1].altstatus_addr = + probe_ent->port[1].ctl_addr = ATA_SECONDARY_CTL; + if (bmdma) { + probe_ent->port[1].bmdma_addr = bmdma + 8; + if (inb(bmdma + 10) & 0x80) + probe_ent->_host_flags |= ATA_HOST_SIMPLEX; + } + ata_std_ports(&probe_ent->port[1]); + probe_ent->pinfo2 = port[1]; + } else + probe_ent->dummy_port_mask |= ATA_PORT_SECONDARY; + + return probe_ent; +} + + +/** + * ata_pci_init_one - Initialize/register PCI IDE host controller + * @pdev: Controller to be initialized + * @port_info: Information from low-level host driver + * @n_ports: Number of ports attached to host controller + * + * This is a helper function which can be called from a driver's + * xxx_init_one() probe function if the hardware uses traditional + * IDE taskfile registers. + * + * This function calls pci_enable_device(), reserves its register + * regions, sets the dma mask, enables bus master mode, and calls + * ata_device_add() + * + * ASSUMPTION: + * Nobody makes a single channel controller that appears solely as + * the secondary legacy port on PCI. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, negative on errno-based value on error. + */ + +int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info, + unsigned int n_ports) +{ + struct ata_probe_ent *probe_ent = NULL; + struct ata_port_info *port[2]; + u8 tmp8, mask; + unsigned int legacy_mode = 0; + int disable_dev_on_err = 1; + int rc; + + DPRINTK("ENTER\n"); + + port[0] = port_info[0]; + if (n_ports > 1) + port[1] = port_info[1]; + else + port[1] = port[0]; + + if ((port[0]->flags & ATA_FLAG_NO_LEGACY) == 0 + && (pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) { + /* TODO: What if one channel is in native mode ... */ + pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8); + mask = (1 << 2) | (1 << 0); + if ((tmp8 & mask) != mask) + legacy_mode = (1 << 3); + } + + /* FIXME... */ + if ((!legacy_mode) && (n_ports > 2)) { + printk(KERN_ERR "ata: BUG: native mode, n_ports > 2\n"); + n_ports = 2; + /* For now */ + } + + /* FIXME: Really for ATA it isn't safe because the device may be + multi-purpose and we want to leave it alone if it was already + enabled. Secondly for shared use as Arjan says we want refcounting + + Checking dev->is_enabled is insufficient as this is not set at + boot for the primary video which is BIOS enabled + */ + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + disable_dev_on_err = 0; + goto err_out; + } + + if (legacy_mode) { + if (!request_region(ATA_PRIMARY_CMD, 8, "libata")) { + struct resource *conflict, res; + res.start = ATA_PRIMARY_CMD; + res.end = ATA_PRIMARY_CMD + 8 - 1; + conflict = ____request_resource(&ioport_resource, &res); + while (conflict->child) + conflict = ____request_resource(conflict, &res); + if (!strcmp(conflict->name, "libata")) + legacy_mode |= ATA_PORT_PRIMARY; + else { + disable_dev_on_err = 0; + printk(KERN_WARNING "ata: 0x%0X IDE port busy\n" \ + "ata: conflict with %s\n", + ATA_PRIMARY_CMD, + conflict->name); + } + } else + legacy_mode |= ATA_PORT_PRIMARY; + + if (!request_region(ATA_SECONDARY_CMD, 8, "libata")) { + struct resource *conflict, res; + res.start = ATA_SECONDARY_CMD; + res.end = ATA_SECONDARY_CMD + 8 - 1; + conflict = ____request_resource(&ioport_resource, &res); + while (conflict->child) + conflict = ____request_resource(conflict, &res); + if (!strcmp(conflict->name, "libata")) + legacy_mode |= ATA_PORT_SECONDARY; + else { + disable_dev_on_err = 0; + printk(KERN_WARNING "ata: 0x%X IDE port busy\n" \ + "ata: conflict with %s\n", + ATA_SECONDARY_CMD, + conflict->name); + } + } else + legacy_mode |= ATA_PORT_SECONDARY; + } + + /* we have legacy mode, but all ports are unavailable */ + if (legacy_mode == (1 << 3)) { + rc = -EBUSY; + goto err_out_regions; + } + + /* FIXME: If we get no DMA mask we should fall back to PIO */ + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + if (legacy_mode) { + probe_ent = ata_pci_init_legacy_port(pdev, port, legacy_mode); + } else { + if (n_ports == 2) + probe_ent = ata_pci_init_native_mode(pdev, port, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY); + else + probe_ent = ata_pci_init_native_mode(pdev, port, ATA_PORT_PRIMARY); + } + if (!probe_ent) { + rc = -ENOMEM; + goto err_out_regions; + } + + pci_set_master(pdev); + + /* FIXME: check ata_device_add return */ + ata_device_add(probe_ent); + + kfree(probe_ent); + + return 0; + +err_out_regions: + if (legacy_mode & ATA_PORT_PRIMARY) + release_region(ATA_PRIMARY_CMD, 8); + if (legacy_mode & ATA_PORT_SECONDARY) + release_region(ATA_SECONDARY_CMD, 8); + pci_release_regions(pdev); +err_out: + if (disable_dev_on_err) + pci_disable_device(pdev); + return rc; +} + +/** + * ata_pci_clear_simplex - attempt to kick device out of simplex + * @pdev: PCI device + * + * Some PCI ATA devices report simplex mode but in fact can be told to + * enter non simplex mode. This implements the neccessary logic to + * perform the task on such devices. Calling it on other devices will + * have -undefined- behaviour. + */ + +int ata_pci_clear_simplex(struct pci_dev *pdev) +{ + unsigned long bmdma = pci_resource_start(pdev, 4); + u8 simplex; + + if (bmdma == 0) + return -ENOENT; + + simplex = inb(bmdma + 0x02); + outb(simplex & 0x60, bmdma + 0x02); + simplex = inb(bmdma + 0x02); + if (simplex & 0x80) + return -EOPNOTSUPP; + return 0; +} + +unsigned long ata_pci_default_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long xfer_mask) +{ + /* Filter out DMA modes if the device has been configured by + the BIOS as PIO only */ + + if (ap->ioaddr.bmdma_addr == 0) + xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); + return xfer_mask; +} + +#endif /* CONFIG_PCI */ + diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h new file mode 100644 index 00000000000..a5ecb71390a --- /dev/null +++ b/drivers/ata/libata.h @@ -0,0 +1,122 @@ +/* + * libata.h - helper library for ATA + * + * Copyright 2003-2004 Red Hat, Inc. All rights reserved. + * Copyright 2003-2004 Jeff Garzik + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + */ + +#ifndef __LIBATA_H__ +#define __LIBATA_H__ + +#define DRV_NAME "libata" +#define DRV_VERSION "2.00" /* must be exactly four chars */ + +struct ata_scsi_args { + struct ata_device *dev; + u16 *id; + struct scsi_cmnd *cmd; + void (*done)(struct scsi_cmnd *); +}; + +/* libata-core.c */ +extern struct workqueue_struct *ata_aux_wq; +extern int atapi_enabled; +extern int atapi_dmadir; +extern int libata_fua; +extern struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev); +extern int ata_rwcmd_protocol(struct ata_queued_cmd *qc); +extern void ata_dev_disable(struct ata_device *dev); +extern void ata_port_flush_task(struct ata_port *ap); +extern unsigned ata_exec_internal(struct ata_device *dev, + struct ata_taskfile *tf, const u8 *cdb, + int dma_dir, void *buf, unsigned int buflen); +extern unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd); +extern int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class, + int post_reset, u16 *id); +extern int ata_dev_configure(struct ata_device *dev, int print_info); +extern int sata_down_spd_limit(struct ata_port *ap); +extern int sata_set_spd_needed(struct ata_port *ap); +extern int ata_down_xfermask_limit(struct ata_device *dev, int force_pio0); +extern int ata_set_mode(struct ata_port *ap, struct ata_device **r_failed_dev); +extern void ata_qc_free(struct ata_queued_cmd *qc); +extern void ata_qc_issue(struct ata_queued_cmd *qc); +extern void __ata_qc_complete(struct ata_queued_cmd *qc); +extern int ata_check_atapi_dma(struct ata_queued_cmd *qc); +extern void ata_dev_select(struct ata_port *ap, unsigned int device, + unsigned int wait, unsigned int can_sleep); +extern void swap_buf_le16(u16 *buf, unsigned int buf_words); +extern int ata_flush_cache(struct ata_device *dev); +extern void ata_dev_init(struct ata_device *dev); +extern int ata_task_ioctl(struct scsi_device *scsidev, void __user *arg); +extern int ata_cmd_ioctl(struct scsi_device *scsidev, void __user *arg); +extern void ata_port_init(struct ata_port *ap, struct ata_host *host, + const struct ata_probe_ent *ent, unsigned int port_no); +extern struct ata_probe_ent *ata_probe_ent_alloc(struct device *dev, + const struct ata_port_info *port); + + +/* libata-scsi.c */ +extern struct scsi_transport_template ata_scsi_transport_template; + +extern void ata_scsi_scan_host(struct ata_port *ap); +extern int ata_scsi_offline_dev(struct ata_device *dev); +extern void ata_scsi_hotplug(void *data); +extern unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); + +extern unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); + +extern unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); +extern unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); +extern unsigned int ata_scsiop_noop(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); +extern unsigned int ata_scsiop_sync_cache(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); +extern unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); +extern unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); +extern unsigned int ata_scsiop_report_luns(struct ata_scsi_args *args, u8 *rbuf, + unsigned int buflen); +extern void ata_scsi_badcmd(struct scsi_cmnd *cmd, + void (*done)(struct scsi_cmnd *), + u8 asc, u8 ascq); +extern void ata_scsi_set_sense(struct scsi_cmnd *cmd, + u8 sk, u8 asc, u8 ascq); +extern void ata_scsi_rbuf_fill(struct ata_scsi_args *args, + unsigned int (*actor) (struct ata_scsi_args *args, + u8 *rbuf, unsigned int buflen)); +extern void ata_schedule_scsi_eh(struct Scsi_Host *shost); +extern void ata_scsi_dev_rescan(void *data); +extern int ata_bus_probe(struct ata_port *ap); + +/* libata-eh.c */ +extern enum scsi_eh_timer_return ata_scsi_timed_out(struct scsi_cmnd *cmd); +extern void ata_scsi_error(struct Scsi_Host *host); +extern void ata_port_wait_eh(struct ata_port *ap); +extern void ata_qc_schedule_eh(struct ata_queued_cmd *qc); + +#endif /* __LIBATA_H__ */ diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c new file mode 100644 index 00000000000..87af3b5861a --- /dev/null +++ b/drivers/ata/pata_ali.c @@ -0,0 +1,679 @@ +/* + * pata_ali.c - ALI 15x3 PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based in part upon + * linux/drivers/ide/pci/alim15x3.c Version 0.17 2003/01/02 + * + * Copyright (C) 1998-2000 Michel Aubry, Maintainer + * Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer + * Copyright (C) 1999-2000 CJ, cjtsai@ali.com.tw, Maintainer + * + * Copyright (C) 1998-2000 Andre Hedrick (andre@linux-ide.org) + * May be copied or modified under the terms of the GNU General Public License + * Copyright (C) 2002 Alan Cox <alan@redhat.com> + * ALi (now ULi M5228) support by Clear Zhang <Clear.Zhang@ali.com.tw> + * + * Documentation + * Chipset documentation available under NDA only + * + * TODO/CHECK + * Cannot have ATAPI on both master & slave for rev < c2 (???) but + * otherwise should do atapi DMA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/dmi.h> + +#define DRV_NAME "pata_ali" +#define DRV_VERSION "0.6.5" + +/* + * Cable special cases + */ + +static struct dmi_system_id cable_dmi_table[] = { + { + .ident = "HP Pavilion N5430", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"), + DMI_MATCH(DMI_BOARD_NAME, "OmniBook N32N-736"), + }, + }, + { } +}; + +static int ali_cable_override(struct pci_dev *pdev) +{ + /* Fujitsu P2000 */ + if (pdev->subsystem_vendor == 0x10CF && pdev->subsystem_device == 0x10AF) + return 1; + /* Systems by DMI */ + if (dmi_check_system(cable_dmi_table)) + return 1; + return 0; +} + +/** + * ali_c2_cable_detect - cable detection + * @ap: ATA port + * + * Perform cable detection for C2 and later revisions + */ + +static int ali_c2_cable_detect(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ata66; + + /* Certain laptops use short but suitable cables and don't + implement the detect logic */ + + if (ali_cable_override(pdev)) + return ATA_CBL_PATA80; + + /* Host view cable detect 0x4A bit 0 primary bit 1 secondary + Bit set for 40 pin */ + pci_read_config_byte(pdev, 0x4A, &ata66); + if (ata66 & (1 << ap->port_no)) + return ATA_CBL_PATA40; + else + return ATA_CBL_PATA80; +} + +/** + * ali_early_error_handler - reset for eary chip + * @ap: ATA port + * + * Handle the reset callback for the later chips with cable detect + */ + +static int ali_c2_pre_reset(struct ata_port *ap) +{ + ap->cbl = ali_c2_cable_detect(ap); + return ata_std_prereset(ap); +} + +static void ali_c2_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, ali_c2_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * ali_early_cable_detect - cable detection + * @ap: ATA port + * + * Perform cable detection for older chipsets. This turns out to be + * rather easy to implement + */ + +static int ali_early_cable_detect(struct ata_port *ap) +{ + return ATA_CBL_PATA40; +} + +/** + * ali_early_probe_init - reset for early chip + * @ap: ATA port + * + * Handle the reset callback for the early (pre cable detect) chips. + */ + +static int ali_early_pre_reset(struct ata_port *ap) +{ + ap->cbl = ali_early_cable_detect(ap); + return ata_std_prereset(ap); +} + +static void ali_early_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, ali_early_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * ali_20_filter - filter for earlier ALI DMA + * @ap: ALi ATA port + * @adev: attached device + * + * Ensure that we do not do DMA on CD devices. We may be able to + * fix that later on. Also ensure we do not do UDMA on WDC drives + */ + +static unsigned long ali_20_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + char model_num[40]; + /* No DMA on anything but a disk for now */ + if (adev->class != ATA_DEV_ATA) + mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); + ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num)); + if (strstr(model_num, "WDC")) + return mask &= ~ATA_MASK_UDMA; + return ata_pci_default_filter(ap, adev, mask); +} + +/** + * ali_fifo_control - FIFO manager + * @ap: ALi channel to control + * @adev: device for FIFO control + * @on: 0 for off 1 for on + * + * Enable or disable the FIFO on a given device. Because of the way the + * ALi FIFO works it provides a boost on ATA disk but can be confused by + * ATAPI and we must therefore manage it. + */ + +static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int on) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int pio_fifo = 0x54 + ap->port_no; + u8 fifo; + int shift = 4 * adev->devno; + + /* ATA - FIFO on set nibble to 0x05, ATAPI - FIFO off, set nibble to + 0x00. Not all the docs agree but the behaviour we now use is the + one stated in the BIOS Programming Guide */ + + pci_read_config_byte(pdev, pio_fifo, &fifo); + fifo &= ~(0x0F << shift); + if (on) + fifo |= (on << shift); + pci_write_config_byte(pdev, pio_fifo, fifo); +} + +/** + * ali_program_modes - load mode registers + * @ap: ALi channel to load + * @adev: Device the timing is for + * @cmd: Command timing + * @data: Data timing + * @ultra: UDMA timing or zero for off + * + * Loads the timing registers for cmd/data and disable UDMA if + * ultra is zero. If ultra is set then load and enable the UDMA + * timing but do not touch the command/data timing. + */ + +static void ali_program_modes(struct ata_port *ap, struct ata_device *adev, struct ata_timing *t, u8 ultra) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int cas = 0x58 + 4 * ap->port_no; /* Command timing */ + int cbt = 0x59 + 4 * ap->port_no; /* Command timing */ + int drwt = 0x5A + 4 * ap->port_no + adev->devno; /* R/W timing */ + int udmat = 0x56 + ap->port_no; /* UDMA timing */ + int shift = 4 * adev->devno; + u8 udma; + + if (t != NULL) { + t->setup = FIT(t->setup, 1, 8) & 7; + t->act8b = FIT(t->act8b, 1, 8) & 7; + t->rec8b = FIT(t->rec8b, 1, 16) & 15; + t->active = FIT(t->active, 1, 8) & 7; + t->recover = FIT(t->recover, 1, 16) & 15; + + pci_write_config_byte(pdev, cas, t->setup); + pci_write_config_byte(pdev, cbt, (t->act8b << 4) | t->rec8b); + pci_write_config_byte(pdev, drwt, (t->active << 4) | t->recover); + } + + /* Set up the UDMA enable */ + pci_read_config_byte(pdev, udmat, &udma); + udma &= ~(0x0F << shift); + udma |= ultra << shift; + pci_write_config_byte(pdev, udmat, udma); +} + +/** + * ali_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the ALi registers for PIO mode. FIXME: add timings for + * PIO5. + */ + +static void ali_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct ata_device *pair = ata_dev_pair(adev); + struct ata_timing t; + unsigned long T = 1000000000 / 33333; /* PCI clock based */ + + ata_timing_compute(adev, adev->pio_mode, &t, T, 1); + if (pair) { + struct ata_timing p; + ata_timing_compute(pair, pair->pio_mode, &p, T, 1); + ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT); + if (pair->dma_mode) { + ata_timing_compute(pair, pair->dma_mode, &p, T, 1); + ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT); + } + } + + /* PIO FIFO is only permitted on ATA disk */ + if (adev->class != ATA_DEV_ATA) + ali_fifo_control(ap, adev, 0x00); + ali_program_modes(ap, adev, &t, 0); + if (adev->class == ATA_DEV_ATA) + ali_fifo_control(ap, adev, 0x05); + +} + +/** + * ali_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * FIXME: MWDMA timings + */ + +static void ali_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static u8 udma_timing[7] = { 0xC, 0xB, 0xA, 0x9, 0x8, 0xF, 0xD }; + struct ata_device *pair = ata_dev_pair(adev); + struct ata_timing t; + unsigned long T = 1000000000 / 33333; /* PCI clock based */ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + + if (adev->class == ATA_DEV_ATA) + ali_fifo_control(ap, adev, 0x08); + + if (adev->dma_mode >= XFER_UDMA_0) { + ali_program_modes(ap, adev, NULL, udma_timing[adev->dma_mode - XFER_UDMA_0]); + if (adev->dma_mode >= XFER_UDMA_3) { + u8 reg4b; + pci_read_config_byte(pdev, 0x4B, ®4b); + reg4b |= 1; + pci_write_config_byte(pdev, 0x4B, reg4b); + } + } else { + ata_timing_compute(adev, adev->dma_mode, &t, T, 1); + if (pair) { + struct ata_timing p; + ata_timing_compute(pair, pair->pio_mode, &p, T, 1); + ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT); + if (pair->dma_mode) { + ata_timing_compute(pair, pair->dma_mode, &p, T, 1); + ata_timing_merge(&p, &t, &t, ATA_TIMING_SETUP|ATA_TIMING_8BIT); + } + } + ali_program_modes(ap, adev, &t, 0); + } +} + +/** + * ali_lock_sectors - Keep older devices to 255 sector mode + * @ap: ATA port + * @adev: Device + * + * Called during the bus probe for each device that is found. We use + * this call to lock the sector count of the device to 255 or less on + * older ALi controllers. If we didn't do this then large I/O's would + * require LBA48 commands which the older ALi requires are issued by + * slower PIO methods + */ + +static void ali_lock_sectors(struct ata_port *ap, struct ata_device *adev) +{ + adev->max_sectors = 255; +} + +static struct scsi_host_template ali_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + /* Keep LBA28 counts so large I/O's don't turn LBA48 and PIO + with older controllers. Not locked so will grow on C5 or later */ + .max_sectors = 255, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +/* + * Port operations for PIO only ALi + */ + +static struct ata_port_operations ali_early_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = ali_set_piomode, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ali_early_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Port operations for DMA capable ALi without cable + * detect + */ +static struct ata_port_operations ali_20_port_ops = { + .port_disable = ata_port_disable, + + .set_piomode = ali_set_piomode, + .set_dmamode = ali_set_dmamode, + .mode_filter = ali_20_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .dev_config = ali_lock_sectors, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ali_early_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Port operations for DMA capable ALi with cable detect + */ +static struct ata_port_operations ali_c2_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = ali_set_piomode, + .set_dmamode = ali_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .dev_config = ali_lock_sectors, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ali_c2_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Port operations for DMA capable ALi with cable detect and LBA48 + */ +static struct ata_port_operations ali_c5_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = ali_set_piomode, + .set_dmamode = ali_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ali_c2_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * ali_init_one - discovery callback + * @pdev: PCI device ID + * @id: PCI table info + * + * An ALi IDE interface has been discovered. Figure out what revision + * and perform configuration work before handing it to the ATA layer + */ + +static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + static struct ata_port_info info_early = { + .sht = &ali_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .port_ops = &ali_early_port_ops + }; + /* Revision 0x20 added DMA */ + static struct ata_port_info info_20 = { + .sht = &ali_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &ali_20_port_ops + }; + /* Revision 0x20 with support logic added UDMA */ + static struct ata_port_info info_20_udma = { + .sht = &ali_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, /* UDMA33 */ + .port_ops = &ali_20_port_ops + }; + /* Revision 0xC2 adds UDMA66 */ + static struct ata_port_info info_c2 = { + .sht = &ali_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, + .port_ops = &ali_c2_port_ops + }; + /* Revision 0xC3 is UDMA100 */ + static struct ata_port_info info_c3 = { + .sht = &ali_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &ali_c2_port_ops + }; + /* Revision 0xC4 is UDMA133 */ + static struct ata_port_info info_c4 = { + .sht = &ali_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | ATA_FLAG_PIO_LBA48, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &ali_c2_port_ops + }; + /* Revision 0xC5 is UDMA133 with LBA48 DMA */ + static struct ata_port_info info_c5 = { + .sht = &ali_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &ali_c5_port_ops + }; + + static struct ata_port_info *port_info[2]; + u8 rev, tmp; + struct pci_dev *north, *isa_bridge; + + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); + + /* + * The chipset revision selects the driver operations and + * mode data. + */ + + if (rev < 0x20) { + port_info[0] = port_info[1] = &info_early; + } else if (rev < 0xC2) { + /* 1543-E/F, 1543C-C, 1543C-D, 1543C-E */ + pci_read_config_byte(pdev, 0x4B, &tmp); + /* Clear CD-ROM DMA write bit */ + tmp &= 0x7F; + pci_write_config_byte(pdev, 0x4B, tmp); + port_info[0] = port_info[1] = &info_20; + } else if (rev == 0xC2) { + port_info[0] = port_info[1] = &info_c2; + } else if (rev == 0xC3) { + port_info[0] = port_info[1] = &info_c3; + } else if (rev == 0xC4) { + port_info[0] = port_info[1] = &info_c4; + } else + port_info[0] = port_info[1] = &info_c5; + + if (rev >= 0xC2) { + /* Enable cable detection logic */ + pci_read_config_byte(pdev, 0x4B, &tmp); + pci_write_config_byte(pdev, 0x4B, tmp | 0x08); + } + + north = pci_get_slot(pdev->bus, PCI_DEVFN(0,0)); + isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL); + + if (north && north->vendor == PCI_VENDOR_ID_AL) { + /* Configure the ALi bridge logic. For non ALi rely on BIOS. + Set the south bridge enable bit */ + pci_read_config_byte(isa_bridge, 0x79, &tmp); + if (rev == 0xC2) + pci_write_config_byte(isa_bridge, 0x79, tmp | 0x04); + else if (rev > 0xC2) + pci_write_config_byte(isa_bridge, 0x79, tmp | 0x02); + } + + if (rev >= 0x20) { + if (rev < 0xC2) { + /* Are we paired with a UDMA capable chip */ + pci_read_config_byte(isa_bridge, 0x5E, &tmp); + if ((tmp & 0x1E) == 0x12) + port_info[0] = port_info[1] = &info_20_udma; + } + /* + * CD_ROM DMA on (0x53 bit 0). Enable this even if we want + * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control + * via 0x54/55. + */ + pci_read_config_byte(pdev, 0x53, &tmp); + if (rev <= 0x20) + tmp &= ~0x02; + if (rev == 0xc7) + tmp |= 0x03; + else + tmp |= 0x01; /* CD_ROM enable for DMA */ + pci_write_config_byte(pdev, 0x53, tmp); + } + + pci_dev_put(isa_bridge); + pci_dev_put(north); + + ata_pci_clear_simplex(pdev); + return ata_pci_init_one(pdev, port_info, 2); +} + +static struct pci_device_id ali[] = { + { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5228), }, + { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5229), }, + { 0, }, +}; + +static struct pci_driver ali_pci_driver = { + .name = DRV_NAME, + .id_table = ali, + .probe = ali_init_one, + .remove = ata_pci_remove_one +}; + +static int __init ali_init(void) +{ + return pci_register_driver(&ali_pci_driver); +} + + +static void __exit ali_exit(void) +{ + pci_unregister_driver(&ali_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for ALi PATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, ali); +MODULE_VERSION(DRV_VERSION); + +module_init(ali_init); +module_exit(ali_exit); diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c new file mode 100644 index 00000000000..599ee266722 --- /dev/null +++ b/drivers/ata/pata_amd.c @@ -0,0 +1,709 @@ +/* + * pata_amd.c - AMD PATA for new ATA layer + * (C) 2005-2006 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based on pata-sil680. Errata information is taken from data sheets + * and the amd74xx.c driver by Vojtech Pavlik. Nvidia SATA devices are + * claimed by sata-nv.c. + * + * TODO: + * Variable system clock when/if it makes sense + * Power management on ports + * + * + * Documentation publically available. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_amd" +#define DRV_VERSION "0.2.4" + +/** + * timing_setup - shared timing computation and load + * @ap: ATA port being set up + * @adev: drive being configured + * @offset: port offset + * @speed: target speed + * @clock: clock multiplier (number of times 33MHz for this part) + * + * Perform the actual timing set up for Nvidia or AMD PATA devices. + * The actual devices vary so they all call into this helper function + * providing the clock multipler and offset (because AMD and Nvidia put + * the ports at different locations). + */ + +static void timing_setup(struct ata_port *ap, struct ata_device *adev, int offset, int speed, int clock) +{ + static const unsigned char amd_cyc2udma[] = { + 6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7 + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct ata_device *peer = ata_dev_pair(adev); + int dn = ap->port_no * 2 + adev->devno; + struct ata_timing at, apeer; + int T, UT; + const int amd_clock = 33333; /* KHz. */ + u8 t; + + T = 1000000000 / amd_clock; + UT = T / min_t(int, max_t(int, clock, 1), 2); + + if (ata_timing_compute(adev, speed, &at, T, UT) < 0) { + dev_printk(KERN_ERR, &pdev->dev, "unknown mode %d.\n", speed); + return; + } + + if (peer) { + /* This may be over conservative */ + if (peer->dma_mode) { + ata_timing_compute(peer, peer->dma_mode, &apeer, T, UT); + ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT); + } + ata_timing_compute(peer, peer->pio_mode, &apeer, T, UT); + ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT); + } + + if (speed == XFER_UDMA_5 && amd_clock <= 33333) at.udma = 1; + if (speed == XFER_UDMA_6 && amd_clock <= 33333) at.udma = 15; + + /* + * Now do the setup work + */ + + /* Configure the address set up timing */ + pci_read_config_byte(pdev, offset + 0x0C, &t); + t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(at.setup, 1, 4) - 1) << ((3 - dn) << 1)); + pci_write_config_byte(pdev, offset + 0x0C , t); + + /* Configure the 8bit I/O timing */ + pci_write_config_byte(pdev, offset + 0x0E + (1 - (dn >> 1)), + ((FIT(at.act8b, 1, 16) - 1) << 4) | (FIT(at.rec8b, 1, 16) - 1)); + + /* Drive timing */ + pci_write_config_byte(pdev, offset + 0x08 + (3 - dn), + ((FIT(at.active, 1, 16) - 1) << 4) | (FIT(at.recover, 1, 16) - 1)); + + switch (clock) { + case 1: + t = at.udma ? (0xc0 | (FIT(at.udma, 2, 5) - 2)) : 0x03; + break; + + case 2: + t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 2, 10)]) : 0x03; + break; + + case 3: + t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 10)]) : 0x03; + break; + + case 4: + t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 15)]) : 0x03; + break; + + default: + return; + } + + /* UDMA timing */ + pci_write_config_byte(pdev, offset + 0x10 + (3 - dn), t); +} + +/** + * amd_probe_init - cable detection + * @ap: ATA port + * + * Perform cable detection. The BIOS stores this in PCI config + * space for us. + */ + +static int amd_pre_reset(struct ata_port *ap) +{ + static const u32 bitmask[2] = {0x03, 0xC0}; + static const struct pci_bits amd_enable_bits[] = { + { 0x40, 1, 0x02, 0x02 }, + { 0x40, 1, 0x01, 0x01 } + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ata66; + + if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no])) + return -ENOENT; + + pci_read_config_byte(pdev, 0x42, &ata66); + if (ata66 & bitmask[ap->port_no]) + ap->cbl = ATA_CBL_PATA80; + else + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); + +} + +static void amd_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, amd_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +static int amd_early_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static struct pci_bits amd_enable_bits[] = { + { 0x40, 1, 0x02, 0x02 }, + { 0x40, 1, 0x01, 0x01 } + }; + + if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no])) + return -ENOENT; + + /* No host side cable detection */ + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); + +} + +static void amd_early_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, amd_early_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * amd33_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the AMD registers for PIO mode. + */ + +static void amd33_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->pio_mode, 1); +} + +static void amd66_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->pio_mode, 2); +} + +static void amd100_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->pio_mode, 3); +} + +static void amd133_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->pio_mode, 4); +} + +/** + * amd33_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the MWDMA/UDMA modes for the AMD and Nvidia + * chipset. + */ + +static void amd33_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->dma_mode, 1); +} + +static void amd66_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->dma_mode, 2); +} + +static void amd100_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->dma_mode, 3); +} + +static void amd133_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x40, adev->dma_mode, 4); +} + + +/** + * nv_probe_init - cable detection + * @ap: ATA port + * + * Perform cable detection. The BIOS stores this in PCI config + * space for us. + */ + +static int nv_pre_reset(struct ata_port *ap) { + static const u8 bitmask[2] = {0x03, 0xC0}; + static const struct pci_bits nv_enable_bits[] = { + { 0x50, 1, 0x02, 0x02 }, + { 0x50, 1, 0x01, 0x01 } + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ata66; + u16 udma; + + if (!pci_test_config_bits(pdev, &nv_enable_bits[ap->port_no])) + return -ENOENT; + + pci_read_config_byte(pdev, 0x52, &ata66); + if (ata66 & bitmask[ap->port_no]) + ap->cbl = ATA_CBL_PATA80; + else + ap->cbl = ATA_CBL_PATA40; + + /* We now have to double check because the Nvidia boxes BIOS + doesn't always set the cable bits but does set mode bits */ + + pci_read_config_word(pdev, 0x62 - 2 * ap->port_no, &udma); + if ((udma & 0xC4) == 0xC4 || (udma & 0xC400) == 0xC400) + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +static void nv_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, nv_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} +/** + * nv100_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the AMD registers for PIO mode. + */ + +static void nv100_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x50, adev->pio_mode, 3); +} + +static void nv133_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x50, adev->pio_mode, 4); +} + +/** + * nv100_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the MWDMA/UDMA modes for the AMD and Nvidia + * chipset. + */ + +static void nv100_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x50, adev->dma_mode, 3); +} + +static void nv133_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + timing_setup(ap, adev, 0x50, adev->dma_mode, 4); +} + +static struct scsi_host_template amd_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations amd33_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = amd33_set_piomode, + .set_dmamode = amd33_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = amd_early_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations amd66_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = amd66_set_piomode, + .set_dmamode = amd66_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = amd_early_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations amd100_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = amd100_set_piomode, + .set_dmamode = amd100_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = amd_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations amd133_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = amd133_set_piomode, + .set_dmamode = amd133_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = amd_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations nv100_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = nv100_set_piomode, + .set_dmamode = nv100_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = nv_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations nv133_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = nv133_set_piomode, + .set_dmamode = nv133_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = nv_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + static struct ata_port_info info[10] = { + { /* 0: AMD 7401 */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, /* No SWDMA */ + .udma_mask = 0x07, /* UDMA 33 */ + .port_ops = &amd33_port_ops + }, + { /* 1: Early AMD7409 - no swdma */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, /* UDMA 66 */ + .port_ops = &amd66_port_ops + }, + { /* 2: AMD 7409, no swdma errata */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, /* UDMA 66 */ + .port_ops = &amd66_port_ops + }, + { /* 3: AMD 7411 */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, /* UDMA 100 */ + .port_ops = &amd100_port_ops + }, + { /* 4: AMD 7441 */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, /* UDMA 100 */ + .port_ops = &amd100_port_ops + }, + { /* 5: AMD 8111*/ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, /* UDMA 133, no swdma */ + .port_ops = &amd133_port_ops + }, + { /* 6: AMD 8111 UDMA 100 (Serenade) */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, /* UDMA 100, no swdma */ + .port_ops = &amd133_port_ops + }, + { /* 7: Nvidia Nforce */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, /* UDMA 100 */ + .port_ops = &nv100_port_ops + }, + { /* 8: Nvidia Nforce2 and later */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, /* UDMA 133, no swdma */ + .port_ops = &nv133_port_ops + }, + { /* 9: AMD CS5536 (Geode companion) */ + .sht = &amd_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, /* UDMA 100 */ + .port_ops = &amd100_port_ops + } + }; + static struct ata_port_info *port_info[2]; + static int printed_version; + int type = id->driver_data; + u8 rev; + u8 fifo; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); + pci_read_config_byte(pdev, 0x41, &fifo); + + /* Check for AMD7409 without swdma errata and if found adjust type */ + if (type == 1 && rev > 0x7) + type = 2; + + /* Check for AMD7411 */ + if (type == 3) + /* FIFO is broken */ + pci_write_config_byte(pdev, 0x41, fifo & 0x0F); + else + pci_write_config_byte(pdev, 0x41, fifo | 0xF0); + + /* Serenade ? */ + if (type == 5 && pdev->subsystem_vendor == PCI_VENDOR_ID_AMD && + pdev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE) + type = 6; /* UDMA 100 only */ + + if (type < 3) + ata_pci_clear_simplex(pdev); + + /* And fire it up */ + + port_info[0] = port_info[1] = &info[type]; + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id amd[] = { + { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_COBRA_7401, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, + { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7409, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 }, + { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 }, + { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_OPUS_7441, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 }, + { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9 }, + { 0, }, +}; + +static struct pci_driver amd_pci_driver = { + .name = DRV_NAME, + .id_table = amd, + .probe = amd_init_one, + .remove = ata_pci_remove_one +}; + +static int __init amd_init(void) +{ + return pci_register_driver(&amd_pci_driver); +} + +static void __exit amd_exit(void) +{ + pci_unregister_driver(&amd_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for AMD PATA IDE"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, amd); +MODULE_VERSION(DRV_VERSION); + +module_init(amd_init); +module_exit(amd_exit); diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c new file mode 100644 index 00000000000..c4ccb75a4f1 --- /dev/null +++ b/drivers/ata/pata_artop.c @@ -0,0 +1,512 @@ +/* + * pata_artop.c - ARTOP ATA controller driver + * + * (C) 2006 Red Hat <alan@redhat.com> + * + * Based in part on drivers/ide/pci/aec62xx.c + * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org> + * 865/865R fixes for Macintosh card version from a patch to the old + * driver by Thibaut VARENE <varenet@parisc-linux.org> + * When setting the PCI latency we must set 0x80 or higher for burst + * performance Alessandro Zummo <alessandro.zummo@towertech.it> + * + * TODO + * 850 serialization once the core supports it + * Investigate no_dsc on 850R + * Clock detect + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_artop" +#define DRV_VERSION "0.4.2" + +/* + * The ARTOP has 33 Mhz and "over clocked" timing tables. Until we + * get PCI bus speed functionality we leave this as 0. Its a variable + * for when we get the functionality and also for folks wanting to + * test stuff. + */ + +static int clock = 0; + +static int artop6210_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + const struct pci_bits artop_enable_bits[] = { + { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) + return -ENOENT; + + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * artop6210_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, artop6210_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * artop6260_pre_reset - check for 40/80 pin + * @ap: Port + * + * The ARTOP hardware reports the cable detect bits in register 0x49. + * Nothing complicated needed here. + */ + +static int artop6260_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits artop_enable_bits[] = { + { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 tmp; + + /* Odd numbered device ids are the units with enable bits (the -R cards) */ + if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) + return -ENOENT; + + pci_read_config_byte(pdev, 0x49, &tmp); + if (tmp & (1 >> ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +/** + * artop6260_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, artop6260_pre_reset, + ata_std_softreset, NULL, + ata_std_postreset); +} + +/** + * artop6210_load_piomode - Load a set of PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device + * @pio: PIO mode + * + * Set PIO mode for device, in host controller PCI config space. This + * is used both to set PIO timings in PIO mode and also to set the + * matching PIO clocking for UDMA, as well as the MWDMA timings. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + const u16 timing[2][5] = { + { 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 }, + { 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 } + + }; + /* Load the PIO timing active/recovery bits */ + pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]); +} + +/** + * artop6210_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * + * Set PIO mode for device, in host controller PCI config space. For + * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In + * the event UDMA is used the later call to set_dmamode will set the + * bits as required. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + u8 ultra; + + artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); + + /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ + pci_read_config_byte(pdev, 0x54, &ultra); + ultra &= ~(3 << (2 * dn)); + pci_write_config_byte(pdev, 0x54, ultra); +} + +/** + * artop6260_load_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * @pio: PIO mode + * + * Set PIO mode for device, in host controller PCI config space. The + * ARTOP6260 and relatives store the timing data differently. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + const u8 timing[2][5] = { + { 0x00, 0x0A, 0x08, 0x33, 0x31 }, + { 0x70, 0x7A, 0x78, 0x43, 0x41 } + + }; + /* Load the PIO timing active/recovery bits */ + pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]); +} + +/** + * artop6260_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * + * Set PIO mode for device, in host controller PCI config space. For + * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In + * the event UDMA is used the later call to set_dmamode will set the + * bits as required. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ultra; + + artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); + + /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ + pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); + ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ + pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); +} + +/** + * artop6210_set_dmamode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set DMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = adev->devno + 2 * ap->port_no; + u8 ultra; + + if (adev->dma_mode == XFER_MW_DMA_0) + pio = 1; + else + pio = 4; + + /* Load the PIO timing active/recovery bits */ + artop6210_load_piomode(ap, adev, pio); + + pci_read_config_byte(pdev, 0x54, &ultra); + ultra &= ~(3 << (2 * dn)); + + /* Add ultra DMA bits if in UDMA mode */ + if (adev->dma_mode >= XFER_UDMA_0) { + u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock; + if (mode == 0) + mode = 1; + ultra |= (mode << (2 * dn)); + } + pci_write_config_byte(pdev, 0x54, ultra); +} + +/** + * artop6260_set_dmamode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring + * + * Set DMA mode for device, in host controller PCI config space. The + * ARTOP6260 and relatives store the timing data differently. + * + * LOCKING: + * None (inherited from caller). + */ + +static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 ultra; + + if (adev->dma_mode == XFER_MW_DMA_0) + pio = 1; + else + pio = 4; + + /* Load the PIO timing active/recovery bits */ + artop6260_load_piomode(ap, adev, pio); + + /* Add ultra DMA bits if in UDMA mode */ + pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); + ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ + if (adev->dma_mode >= XFER_UDMA_0) { + u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock; + if (mode == 0) + mode = 1; + ultra |= (mode << (4 * adev->devno)); + } + pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); +} + +static struct scsi_host_template artop_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations artop6210_ops = { + .port_disable = ata_port_disable, + .set_piomode = artop6210_set_piomode, + .set_dmamode = artop6210_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = artop6210_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations artop6260_ops = { + .port_disable = ata_port_disable, + .set_piomode = artop6260_set_piomode, + .set_dmamode = artop6260_set_dmamode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = artop6260_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + + +/** + * artop_init_one - Register ARTOP ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in artop_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id) +{ + static int printed_version; + static struct ata_port_info info_6210 = { + .sht = &artop_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA2, + .port_ops = &artop6210_ops, + }; + static struct ata_port_info info_626x = { + .sht = &artop_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA4, + .port_ops = &artop6260_ops, + }; + static struct ata_port_info info_626x_fast = { + .sht = &artop_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA5, + .port_ops = &artop6260_ops, + }; + struct ata_port_info *port_info[2]; + struct ata_port_info *info; + int ports = 2; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + if (id->driver_data == 0) { /* 6210 variant */ + info = &info_6210; + /* BIOS may have left us in UDMA, clear it before libata probe */ + pci_write_config_byte(pdev, 0x54, 0); + /* For the moment (also lacks dsc) */ + printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n"); + printk(KERN_WARNING "Secondary ATA ports will not be activated.\n"); + ports = 1; + } + else if (id->driver_data == 1) /* 6260 */ + info = &info_626x; + else if (id->driver_data == 2) { /* 6260 or 6260 + fast */ + unsigned long io = pci_resource_start(pdev, 4); + u8 reg; + + info = &info_626x; + if (inb(io) & 0x10) + info = &info_626x_fast; + /* Mac systems come up with some registers not set as we + will need them */ + + /* Clear reset & test bits */ + pci_read_config_byte(pdev, 0x49, ®); + pci_write_config_byte(pdev, 0x49, reg & ~ 0x30); + + /* PCI latency must be > 0x80 for burst mode, tweak it + * if required. + */ + pci_read_config_byte(pdev, PCI_LATENCY_TIMER, ®); + if (reg <= 0x80) + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90); + + /* Enable IRQ output and burst mode */ + pci_read_config_byte(pdev, 0x4a, ®); + pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80); + + } + port_info[0] = port_info[1] = info; + return ata_pci_init_one(pdev, port_info, ports); +} + +static const struct pci_device_id artop_pci_tbl[] = { + { 0x1191, 0x0005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { 0x1191, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, + { 0x1191, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, + { 0x1191, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2}, + { 0x1191, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2}, + { } /* terminate list */ +}; + +static struct pci_driver artop_pci_driver = { + .name = DRV_NAME, + .id_table = artop_pci_tbl, + .probe = artop_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init artop_init(void) +{ + return pci_register_driver(&artop_pci_driver); +} + +static void __exit artop_exit(void) +{ + pci_unregister_driver(&artop_pci_driver); +} + + +module_init(artop_init); +module_exit(artop_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, artop_pci_tbl); +MODULE_VERSION(DRV_VERSION); + diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c new file mode 100644 index 00000000000..6c2269b6bd3 --- /dev/null +++ b/drivers/ata/pata_atiixp.c @@ -0,0 +1,304 @@ +/* + * pata_atiixp.c - ATI PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based on + * + * linux/drivers/ide/pci/atiixp.c Version 0.01-bart2 Feb. 26, 2004 + * + * Copyright (C) 2003 ATI Inc. <hyu@ati.com> + * Copyright (C) 2004 Bartlomiej Zolnierkiewicz + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_atiixp" +#define DRV_VERSION "0.4.3" + +enum { + ATIIXP_IDE_PIO_TIMING = 0x40, + ATIIXP_IDE_MWDMA_TIMING = 0x44, + ATIIXP_IDE_PIO_CONTROL = 0x48, + ATIIXP_IDE_PIO_MODE = 0x4a, + ATIIXP_IDE_UDMA_CONTROL = 0x54, + ATIIXP_IDE_UDMA_MODE = 0x56 +}; + +static int atiixp_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static struct pci_bits atiixp_enable_bits[] = { + { 0x48, 1, 0x01, 0x00 }, + { 0x48, 1, 0x08, 0x00 } + }; + + if (!pci_test_config_bits(pdev, &atiixp_enable_bits[ap->port_no])) + return -ENOENT; + + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +static void atiixp_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, atiixp_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * atiixp_set_pio_timing - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called by both the pio and dma setup functions to set the controller + * timings for PIO transfers. We must load both the mode number and + * timing values into the controller. + */ + +static void atiixp_set_pio_timing(struct ata_port *ap, struct ata_device *adev, int pio) +{ + static u8 pio_timings[5] = { 0x5D, 0x47, 0x34, 0x22, 0x20 }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = 2 * ap->port_no + adev->devno; + + /* Check this is correct - the order is odd in both drivers */ + int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); + u16 pio_mode_data, pio_timing_data; + + pci_read_config_word(pdev, ATIIXP_IDE_PIO_MODE, &pio_mode_data); + pio_mode_data &= ~(0x7 << (4 * dn)); + pio_mode_data |= pio << (4 * dn); + pci_write_config_word(pdev, ATIIXP_IDE_PIO_MODE, pio_mode_data); + + pci_read_config_word(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data); + pio_mode_data &= ~(0xFF << timing_shift); + pio_mode_data |= (pio_timings[pio] << timing_shift); + pci_write_config_word(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data); +} + +/** + * atiixp_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. We use a shared helper for this + * as the DMA setup must also adjust the PIO timing information. + */ + +static void atiixp_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + atiixp_set_pio_timing(ap, adev, adev->pio_mode - XFER_PIO_0); +} + +/** + * atiixp_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the DMA mode setup. We use timing tables for most + * modes but must tune an appropriate PIO mode to match. + */ + +static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static u8 mwdma_timings[5] = { 0x77, 0x21, 0x20 }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dma = adev->dma_mode; + int dn = 2 * ap->port_no + adev->devno; + int wanted_pio; + + if (adev->dma_mode >= XFER_UDMA_0) { + u16 udma_mode_data; + + dma -= XFER_UDMA_0; + + pci_read_config_word(pdev, ATIIXP_IDE_UDMA_MODE, &udma_mode_data); + udma_mode_data &= ~(0x7 << (4 * dn)); + udma_mode_data |= dma << (4 * dn); + pci_write_config_word(pdev, ATIIXP_IDE_UDMA_MODE, udma_mode_data); + } else { + u16 mwdma_timing_data; + /* Check this is correct - the order is odd in both drivers */ + int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); + + dma -= XFER_MW_DMA_0; + + pci_read_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, &mwdma_timing_data); + mwdma_timing_data &= ~(0xFF << timing_shift); + mwdma_timing_data |= (mwdma_timings[dma] << timing_shift); + pci_write_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, mwdma_timing_data); + } + /* + * We must now look at the PIO mode situation. We may need to + * adjust the PIO mode to keep the timings acceptable + */ + if (adev->dma_mode >= XFER_MW_DMA_2) + wanted_pio = 4; + else if (adev->dma_mode == XFER_MW_DMA_1) + wanted_pio = 3; + else if (adev->dma_mode == XFER_MW_DMA_0) + wanted_pio = 0; + else BUG(); + + if (adev->pio_mode != wanted_pio) + atiixp_set_pio_timing(ap, adev, wanted_pio); +} + +/** + * atiixp_bmdma_start - DMA start callback + * @qc: Command in progress + * + * When DMA begins we need to ensure that the UDMA control + * register for the channel is correctly set. + */ + +static void atiixp_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = (2 * ap->port_no) + adev->devno; + u16 tmp16; + + pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16); + if (adev->dma_mode >= XFER_UDMA_0) + tmp16 |= (1 << dn); + else + tmp16 &= ~(1 << dn); + pci_write_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, tmp16); + ata_bmdma_start(qc); +} + +/** + * atiixp_dma_stop - DMA stop callback + * @qc: Command in progress + * + * DMA has completed. Clear the UDMA flag as the next operations will + * be PIO ones not UDMA data transfer. + */ + +static void atiixp_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int dn = (2 * ap->port_no) + qc->dev->devno; + u16 tmp16; + + pci_read_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, &tmp16); + tmp16 &= ~(1 << dn); + pci_write_config_word(pdev, ATIIXP_IDE_UDMA_CONTROL, tmp16); + ata_bmdma_stop(qc); +} + +static struct scsi_host_template atiixp_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations atiixp_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = atiixp_set_piomode, + .set_dmamode = atiixp_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = atiixp_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = atiixp_bmdma_start, + .bmdma_stop = atiixp_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int atiixp_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &atiixp_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x06, /* No MWDMA0 support */ + .udma_mask = 0x3F, + .port_ops = &atiixp_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id atiixp[] = { + { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP200_IDE), }, + { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_IDE), }, + { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_IDE), }, + { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_IDE), }, + { 0, }, +}; + +static struct pci_driver atiixp_pci_driver = { + .name = DRV_NAME, + .id_table = atiixp, + .probe = atiixp_init_one, + .remove = ata_pci_remove_one +}; + +static int __init atiixp_init(void) +{ + return pci_register_driver(&atiixp_pci_driver); +} + + +static void __exit atiixp_exit(void) +{ + pci_unregister_driver(&atiixp_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for ATI IXP200/300/400"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, atiixp); +MODULE_VERSION(DRV_VERSION); + +module_init(atiixp_init); +module_exit(atiixp_exit); diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c new file mode 100644 index 00000000000..e92b0ef43ec --- /dev/null +++ b/drivers/ata/pata_cmd64x.c @@ -0,0 +1,505 @@ +/* + * pata_cmd64x.c - ATI PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based upon + * linux/drivers/ide/pci/cmd64x.c Version 1.30 Sept 10, 2002 + * + * cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines. + * Note, this driver is not used at all on other systems because + * there the "BIOS" has done all of the following already. + * Due to massive hardware bugs, UltraDMA is only supported + * on the 646U2 and not on the 646U. + * + * Copyright (C) 1998 Eddie C. Dost (ecd@skynet.be) + * Copyright (C) 1998 David S. Miller (davem@redhat.com) + * + * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org> + * + * TODO + * Testing work + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_cmd64x" +#define DRV_VERSION "0.2.1" + +/* + * CMD64x specific registers definition. + */ + +enum { + CFR = 0x50, + CFR_INTR_CH0 = 0x02, + CNTRL = 0x51, + CNTRL_DIS_RA0 = 0x40, + CNTRL_DIS_RA1 = 0x80, + CNTRL_ENA_2ND = 0x08, + CMDTIM = 0x52, + ARTTIM0 = 0x53, + DRWTIM0 = 0x54, + ARTTIM1 = 0x55, + DRWTIM1 = 0x56, + ARTTIM23 = 0x57, + ARTTIM23_DIS_RA2 = 0x04, + ARTTIM23_DIS_RA3 = 0x08, + ARTTIM23_INTR_CH1 = 0x10, + ARTTIM2 = 0x57, + ARTTIM3 = 0x57, + DRWTIM23 = 0x58, + DRWTIM2 = 0x58, + BRST = 0x59, + DRWTIM3 = 0x5b, + BMIDECR0 = 0x70, + MRDMODE = 0x71, + MRDMODE_INTR_CH0 = 0x04, + MRDMODE_INTR_CH1 = 0x08, + MRDMODE_BLK_CH0 = 0x10, + MRDMODE_BLK_CH1 = 0x20, + BMIDESR0 = 0x72, + UDIDETCR0 = 0x73, + DTPR0 = 0x74, + BMIDECR1 = 0x78, + BMIDECSR = 0x79, + BMIDESR1 = 0x7A, + UDIDETCR1 = 0x7B, + DTPR1 = 0x7C +}; + +static int cmd64x_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +static int cmd648_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 r; + + /* Check cable detect bits */ + pci_read_config_byte(pdev, BMIDECSR, &r); + if (r & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA80; + else + ap->cbl = ATA_CBL_PATA40; + + return ata_std_prereset(ap); +} + +static void cmd64x_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, cmd64x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +static void cmd648_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, cmd648_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * cmd64x_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. + */ + +static void cmd64x_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct ata_timing t; + const unsigned long T = 1000000 / 33; + const u8 setup_data[] = { 0x40, 0x40, 0x40, 0x80, 0x00 }; + + u8 reg; + + /* Port layout is not logical so use a table */ + const u8 arttim_port[2][2] = { + { ARTTIM0, ARTTIM1 }, + { ARTTIM23, ARTTIM23 } + }; + const u8 drwtim_port[2][2] = { + { DRWTIM0, DRWTIM1 }, + { DRWTIM2, DRWTIM3 } + }; + + int arttim = arttim_port[ap->port_no][adev->devno]; + int drwtim = drwtim_port[ap->port_no][adev->devno]; + + + if (ata_timing_compute(adev, adev->pio_mode, &t, T, 0) < 0) { + printk(KERN_ERR DRV_NAME ": mode computation failed.\n"); + return; + } + if (ap->port_no) { + /* Slave has shared address setup */ + struct ata_device *pair = ata_dev_pair(adev); + + if (pair) { + struct ata_timing tp; + ata_timing_compute(pair, pair->pio_mode, &tp, T, 0); + ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP); + } + } + + printk(KERN_DEBUG DRV_NAME ": active %d recovery %d setup %d.\n", + t.active, t.recover, t.setup); + if (t.recover > 16) { + t.active += t.recover - 16; + t.recover = 16; + } + if (t.active > 16) + t.active = 16; + + /* Now convert the clocks into values we can actually stuff into + the chip */ + + if (t.recover > 1) + t.recover--; + else + t.recover = 15; + + if (t.setup > 4) + t.setup = 0xC0; + else + t.setup = setup_data[t.setup]; + + t.active &= 0x0F; /* 0 = 16 */ + + /* Load setup timing */ + pci_read_config_byte(pdev, arttim, ®); + reg &= 0x3F; + reg |= t.setup; + pci_write_config_byte(pdev, arttim, reg); + + /* Load active/recovery */ + pci_write_config_byte(pdev, drwtim, (t.active << 4) | t.recover); +} + +/** + * cmd64x_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the DMA mode setup. + */ + +static void cmd64x_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const u8 udma_data[] = { + 0x31, 0x21, 0x11, 0x25, 0x15, 0x05 + }; + static const u8 mwdma_data[] = { + 0x30, 0x20, 0x10 + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 regU, regD; + + int pciU = UDIDETCR0 + 8 * ap->port_no; + int pciD = BMIDESR0 + 8 * ap->port_no; + int shift = 2 * adev->devno; + + pci_read_config_byte(pdev, pciD, ®D); + pci_read_config_byte(pdev, pciU, ®U); + + regD &= ~(0x20 << shift); + regU &= ~(0x35 << shift); + + if (adev->dma_mode >= XFER_UDMA_0) + regU |= udma_data[adev->dma_mode - XFER_UDMA_0] << shift; + else + regD |= mwdma_data[adev->dma_mode - XFER_MW_DMA_0] << shift; + + regD |= 0x20 << adev->devno; + + pci_write_config_byte(pdev, pciU, regU); + pci_write_config_byte(pdev, pciD, regD); +} + +/** + * cmd648_dma_stop - DMA stop callback + * @qc: Command in progress + * + * DMA has completed. + */ + +static void cmd648_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 dma_intr; + int dma_reg = ap->port_no ? ARTTIM23_INTR_CH1 : CFR_INTR_CH0; + int dma_mask = ap->port_no ? ARTTIM2 : CFR; + + ata_bmdma_stop(qc); + + pci_read_config_byte(pdev, dma_reg, &dma_intr); + pci_write_config_byte(pdev, dma_reg, dma_intr | dma_mask); +} + +/** + * cmd646r1_dma_stop - DMA stop callback + * @qc: Command in progress + * + * Stub for now while investigating the r1 quirk in the old driver. + */ + +static void cmd646r1_bmdma_stop(struct ata_queued_cmd *qc) +{ + ata_bmdma_stop(qc); +} + +static struct scsi_host_template cmd64x_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations cmd64x_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cmd64x_set_piomode, + .set_dmamode = cmd64x_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cmd64x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations cmd646r1_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cmd64x_set_piomode, + .set_dmamode = cmd64x_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cmd64x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = cmd646r1_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations cmd648_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cmd64x_set_piomode, + .set_dmamode = cmd64x_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cmd648_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = cmd648_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + u32 class_rev; + + static struct ata_port_info cmd_info[6] = { + { /* CMD 643 - no UDMA */ + .sht = &cmd64x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &cmd64x_port_ops + }, + { /* CMD 646 with broken UDMA */ + .sht = &cmd64x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &cmd64x_port_ops + }, + { /* CMD 646 with working UDMA */ + .sht = &cmd64x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA1, + .port_ops = &cmd64x_port_ops + }, + { /* CMD 646 rev 1 */ + .sht = &cmd64x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &cmd646r1_port_ops + }, + { /* CMD 648 */ + .sht = &cmd64x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA2, + .port_ops = &cmd648_port_ops + }, + { /* CMD 649 */ + .sht = &cmd64x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA3, + .port_ops = &cmd648_port_ops + } + }; + static struct ata_port_info *port_info[2], *info; + u8 mrdmode; + + info = &cmd_info[id->driver_data]; + + pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xFF; + + if (id->driver_data == 0) /* 643 */ + ata_pci_clear_simplex(pdev); + + if (pdev->device == PCI_DEVICE_ID_CMD_646) { + /* Does UDMA work ? */ + if (class_rev > 4) + info = &cmd_info[2]; + /* Early rev with other problems ? */ + else if (class_rev == 1) + info = &cmd_info[3]; + } + + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64); + pci_read_config_byte(pdev, MRDMODE, &mrdmode); + mrdmode &= ~ 0x30; /* IRQ set up */ + mrdmode |= 0x02; /* Memory read line enable */ + pci_write_config_byte(pdev, MRDMODE, mrdmode); + + /* Force PIO 0 here.. */ + + /* PPC specific fixup copied from old driver */ +#ifdef CONFIG_PPC + pci_write_config_byte(pdev, UDIDETCR0, 0xF0); +#endif + + port_info[0] = port_info[1] = info; + return ata_pci_init_one(pdev, port_info, 2); +} + +static struct pci_device_id cmd64x[] = { + { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_643, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_646, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, + { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_648, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4}, + { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_CMD_649, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5}, + { 0, }, +}; + +static struct pci_driver cmd64x_pci_driver = { + .name = DRV_NAME, + .id_table = cmd64x, + .probe = cmd64x_init_one, + .remove = ata_pci_remove_one +}; + +static int __init cmd64x_init(void) +{ + return pci_register_driver(&cmd64x_pci_driver); +} + + +static void __exit cmd64x_exit(void) +{ + pci_unregister_driver(&cmd64x_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for CMD64x series PATA controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, cmd64x); +MODULE_VERSION(DRV_VERSION); + +module_init(cmd64x_init); +module_exit(cmd64x_exit); diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c new file mode 100644 index 00000000000..a6c6cebd0da --- /dev/null +++ b/drivers/ata/pata_cs5520.c @@ -0,0 +1,334 @@ +/* + * IDE tuning and bus mastering support for the CS5510/CS5520 + * chipsets + * + * The CS5510/CS5520 are slightly unusual devices. Unlike the + * typical IDE controllers they do bus mastering with the drive in + * PIO mode and smarter silicon. + * + * The practical upshot of this is that we must always tune the + * drive for the right PIO mode. We must also ignore all the blacklists + * and the drive bus mastering DMA information. Also to confuse matters + * further we can do DMA on PIO only drives. + * + * DMA on the 5510 also requires we disable_hlt() during DMA on early + * revisions. + * + * *** This driver is strictly experimental *** + * + * (c) Copyright Red Hat Inc 2002 + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2, or (at your option) any + * later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * Documentation: + * Not publically available. + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_cs5520" +#define DRV_VERSION "0.6.2" + +struct pio_clocks +{ + int address; + int assert; + int recovery; +}; + +static const struct pio_clocks cs5520_pio_clocks[]={ + {3, 6, 11}, + {2, 5, 6}, + {1, 4, 3}, + {1, 3, 2}, + {1, 2, 1} +}; + +/** + * cs5520_set_timings - program PIO timings + * @ap: ATA port + * @adev: ATA device + * + * Program the PIO mode timings for the controller according to the pio + * clocking table. + */ + +static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int slave = adev->devno; + + pio -= XFER_PIO_0; + + /* Channel command timing */ + pci_write_config_byte(pdev, 0x62 + ap->port_no, + (cs5520_pio_clocks[pio].recovery << 4) | + (cs5520_pio_clocks[pio].assert)); + /* FIXME: should these use address ? */ + /* Read command timing */ + pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave, + (cs5520_pio_clocks[pio].recovery << 4) | + (cs5520_pio_clocks[pio].assert)); + /* Write command timing */ + pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave, + (cs5520_pio_clocks[pio].recovery << 4) | + (cs5520_pio_clocks[pio].assert)); +} + +/** + * cs5520_enable_dma - turn on DMA bits + * + * Turn on the DMA bits for this disk. Needed because the BIOS probably + * has not done the work for us. Belongs in the core SATA code. + */ + +static void cs5520_enable_dma(struct ata_port *ap, struct ata_device *adev) +{ + /* Set the DMA enable/disable flag */ + u8 reg = inb(ap->ioaddr.bmdma_addr + 0x02); + reg |= 1<<(adev->devno + 5); + outb(reg, ap->ioaddr.bmdma_addr + 0x02); +} + +/** + * cs5520_set_dmamode - program DMA timings + * @ap: ATA port + * @adev: ATA device + * + * Program the DMA mode timings for the controller according to the pio + * clocking table. Note that this device sets the DMA timings to PIO + * mode values. This may seem bizarre but the 5520 architecture talks + * PIO mode to the disk and DMA mode to the controller so the underlying + * transfers are PIO timed. + */ + +static void cs5520_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 }; + cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]); + cs5520_enable_dma(ap, adev); +} + +/** + * cs5520_set_piomode - program PIO timings + * @ap: ATA port + * @adev: ATA device + * + * Program the PIO mode timings for the controller according to the pio + * clocking table. We know pio_mode will equal dma_mode because of the + * CS5520 architecture. At least once we turned DMA on and wrote a + * mode setter. + */ + +static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + cs5520_set_timings(ap, adev, adev->pio_mode); +} + + +static int cs5520_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +static void cs5520_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, cs5520_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +static struct scsi_host_template cs5520_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations cs5520_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cs5520_set_piomode, + .set_dmamode = cs5520_set_dmamode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cs5520_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + u8 pcicfg; + static struct ata_probe_ent probe[2]; + int ports = 0; + + /* IDE port enable bits */ + pci_read_config_byte(dev, 0x60, &pcicfg); + + /* Check if the ATA ports are enabled */ + if ((pcicfg & 3) == 0) + return -ENODEV; + + if ((pcicfg & 0x40) == 0) { + printk(KERN_WARNING DRV_NAME ": DMA mode disabled. Enabling.\n"); + pci_write_config_byte(dev, 0x60, pcicfg | 0x40); + } + + /* Perform set up for DMA */ + if (pci_enable_device_bars(dev, 1<<2)) { + printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n"); + return -ENODEV; + } + pci_set_master(dev); + if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) { + printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n"); + return -ENODEV; + } + if (pci_set_consistent_dma_mask(dev, DMA_32BIT_MASK)) { + printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n"); + return -ENODEV; + } + + /* We have to do our own plumbing as the PCI setup for this + chipset is non-standard so we can't punt to the libata code */ + + INIT_LIST_HEAD(&probe[0].node); + probe[0].dev = pci_dev_to_dev(dev); + probe[0].port_ops = &cs5520_port_ops; + probe[0].sht = &cs5520_sht; + probe[0].pio_mask = 0x1F; + probe[0].mwdma_mask = id->driver_data; + probe[0].irq = 14; + probe[0].irq_flags = 0; + probe[0].port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST; + probe[0].n_ports = 1; + probe[0].port[0].cmd_addr = 0x1F0; + probe[0].port[0].ctl_addr = 0x3F6; + probe[0].port[0].altstatus_addr = 0x3F6; + probe[0].port[0].bmdma_addr = pci_resource_start(dev, 2); + + /* The secondary lurks at different addresses but is otherwise + the same beastie */ + + probe[1] = probe[0]; + INIT_LIST_HEAD(&probe[1].node); + probe[1].irq = 15; + probe[1].port[0].cmd_addr = 0x170; + probe[1].port[0].ctl_addr = 0x376; + probe[1].port[0].altstatus_addr = 0x376; + probe[1].port[0].bmdma_addr = pci_resource_start(dev, 2) + 8; + + /* Let libata fill in the port details */ + ata_std_ports(&probe[0].port[0]); + ata_std_ports(&probe[1].port[0]); + + /* Now add the ports that are active */ + if (pcicfg & 1) + ports += ata_device_add(&probe[0]); + if (pcicfg & 2) + ports += ata_device_add(&probe[1]); + if (ports) + return 0; + return -ENODEV; +} + +/** + * cs5520_remove_one - device unload + * @pdev: PCI device being removed + * + * Handle an unplug/unload event for a PCI device. Unload the + * PCI driver but do not use the default handler as we manage + * resources ourself and *MUST NOT* disable the device as it has + * other functions. + */ + +static void __devexit cs5520_remove_one(struct pci_dev *pdev) +{ + struct device *dev = pci_dev_to_dev(pdev); + struct ata_host *host = dev_get_drvdata(dev); + + ata_host_remove(host); + dev_set_drvdata(dev, NULL); +} + +/* For now keep DMA off. We can set it for all but A rev CS5510 once the + core ATA code can handle it */ + +static struct pci_device_id pata_cs5520[] = { + { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5510), }, + { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5520), }, + { 0, }, +}; + +static struct pci_driver cs5520_pci_driver = { + .name = DRV_NAME, + .id_table = pata_cs5520, + .probe = cs5520_init_one, + .remove = cs5520_remove_one +}; + + +static int __init cs5520_init(void) +{ + return pci_register_driver(&cs5520_pci_driver); +} + +static void __exit cs5520_exit(void) +{ + pci_unregister_driver(&cs5520_pci_driver); +} + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pata_cs5520); +MODULE_VERSION(DRV_VERSION); + +module_init(cs5520_init); +module_exit(cs5520_exit); + diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c new file mode 100644 index 00000000000..7bba4d954e9 --- /dev/null +++ b/drivers/ata/pata_cs5530.c @@ -0,0 +1,387 @@ +/* + * pata-cs5530.c - CS5530 PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based upon cs5530.c by Mark Lord. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Loosely based on the piix & svwks drivers. + * + * Documentation: + * Available from AMD web site. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/dmi.h> + +#define DRV_NAME "pata_cs5530" +#define DRV_VERSION "0.6" + +/** + * cs5530_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Set our PIO requirements. This is fairly simple on the CS5530 + * chips. + */ + +static void cs5530_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const unsigned int cs5530_pio_timings[2][5] = { + {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, + {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010} + }; + unsigned long base = ( ap->ioaddr.bmdma_addr & ~0x0F) + 0x20 + 0x10 * ap->port_no; + u32 tuning; + int format; + + /* Find out which table to use */ + tuning = inl(base + 0x04); + format = (tuning & 0x80000000UL) ? 1 : 0; + + /* Now load the right timing register */ + if (adev->devno) + base += 0x08; + + outl(cs5530_pio_timings[format][adev->pio_mode - XFER_PIO_0], base); +} + +/** + * cs5530_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * We cannot mix MWDMA and UDMA without reloading timings each switch + * master to slave. We track the last DMA setup in order to minimise + * reloads. + */ + +static void cs5530_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + unsigned long base = ( ap->ioaddr.bmdma_addr & ~0x0F) + 0x20 + 0x10 * ap->port_no; + u32 tuning, timing = 0; + u8 reg; + + /* Find out which table to use */ + tuning = inl(base + 0x04); + + switch(adev->dma_mode) { + case XFER_UDMA_0: + timing = 0x00921250;break; + case XFER_UDMA_1: + timing = 0x00911140;break; + case XFER_UDMA_2: + timing = 0x00911030;break; + case XFER_MW_DMA_0: + timing = 0x00077771;break; + case XFER_MW_DMA_1: + timing = 0x00012121;break; + case XFER_MW_DMA_2: + timing = 0x00002020;break; + default: + BUG(); + } + /* Merge in the PIO format bit */ + timing |= (tuning & 0x80000000UL); + if (adev->devno == 0) /* Master */ + outl(timing, base + 0x04); + else { + if (timing & 0x00100000) + tuning |= 0x00100000; /* UDMA for both */ + else + tuning &= ~0x00100000; /* MWDMA for both */ + outl(tuning, base + 0x04); + outl(timing, base + 0x0C); + } + + /* Set the DMA capable bit in the BMDMA area */ + reg = inb(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); + reg |= (1 << (5 + adev->devno)); + outb(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); + + /* Remember the last DMA setup we did */ + + ap->private_data = adev; +} + +/** + * cs5530_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * neccessary. Specifically we have a problem that there is only + * one MWDMA/UDMA bit. + */ + +static unsigned int cs5530_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_device *prev = ap->private_data; + + /* See if the DMA settings could be wrong */ + if (adev->dma_mode != 0 && adev != prev && prev != NULL) { + /* Maybe, but do the channels match MWDMA/UDMA ? */ + if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) || + (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0)) + /* Switch the mode bits */ + cs5530_set_dmamode(ap, adev); + } + + return ata_qc_issue_prot(qc); +} + +static int cs5530_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +static void cs5530_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, cs5530_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + + +static struct scsi_host_template cs5530_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations cs5530_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cs5530_set_piomode, + .set_dmamode = cs5530_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cs5530_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = cs5530_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct dmi_system_id palmax_dmi_table[] = { + { + .ident = "Palmax PD1100", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Cyrix"), + DMI_MATCH(DMI_PRODUCT_NAME, "Caddis"), + }, + }, + { } +}; + +static int cs5530_is_palmax(void) +{ + if (dmi_check_system(palmax_dmi_table)) { + printk(KERN_INFO "Palmax PD1100: Disabling DMA on docking port.\n"); + return 1; + } + return 0; +} + +/** + * cs5530_init_one - Initialise a CS5530 + * @dev: PCI device + * @id: Entry in match table + * + * Install a driver for the newly found CS5530 companion chip. Most of + * this is just housekeeping. We have to set the chip up correctly and + * turn off various bits of emulation magic. + */ + +static int cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + int compiler_warning_pointless_fix; + struct pci_dev *master_0 = NULL, *cs5530_0 = NULL; + static struct ata_port_info info = { + .sht = &cs5530_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, + .port_ops = &cs5530_port_ops + }; + /* The docking connector doesn't do UDMA, and it seems not MWDMA */ + static struct ata_port_info info_palmax_secondary = { + .sht = &cs5530_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .port_ops = &cs5530_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + + dev = NULL; + while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) { + switch (dev->device) { + case PCI_DEVICE_ID_CYRIX_PCI_MASTER: + master_0 = pci_dev_get(dev); + break; + case PCI_DEVICE_ID_CYRIX_5530_LEGACY: + cs5530_0 = pci_dev_get(dev); + break; + } + } + if (!master_0) { + printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n"); + goto fail_put; + } + if (!cs5530_0) { + printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n"); + goto fail_put; + } + + pci_set_master(cs5530_0); + compiler_warning_pointless_fix = pci_set_mwi(cs5530_0); + + /* + * Set PCI CacheLineSize to 16-bytes: + * --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530 + * + * Note: This value is constant because the 5530 is only a Geode companion + */ + + pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04); + + /* + * Disable trapping of UDMA register accesses (Win98 hack): + * --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530 + */ + + pci_write_config_word(cs5530_0, 0xd0, 0x5006); + + /* + * Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus: + * The other settings are what is necessary to get the register + * into a sane state for IDE DMA operation. + */ + + pci_write_config_byte(master_0, 0x40, 0x1e); + + /* + * Set max PCI burst size (16-bytes seems to work best): + * 16bytes: set bit-1 at 0x41 (reg value of 0x16) + * all others: clear bit-1 at 0x41, and do: + * 128bytes: OR 0x00 at 0x41 + * 256bytes: OR 0x04 at 0x41 + * 512bytes: OR 0x08 at 0x41 + * 1024bytes: OR 0x0c at 0x41 + */ + + pci_write_config_byte(master_0, 0x41, 0x14); + + /* + * These settings are necessary to get the chip + * into a sane state for IDE DMA operation. + */ + + pci_write_config_byte(master_0, 0x42, 0x00); + pci_write_config_byte(master_0, 0x43, 0xc1); + + pci_dev_put(master_0); + pci_dev_put(cs5530_0); + + if (cs5530_is_palmax()) + port_info[1] = &info_palmax_secondary; + + /* Now kick off ATA set up */ + return ata_pci_init_one(dev, port_info, 2); + +fail_put: + if (master_0) + pci_dev_put(master_0); + if (cs5530_0) + pci_dev_put(cs5530_0); + return -ENODEV; +} + +static struct pci_device_id cs5530[] = { + { PCI_DEVICE(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), }, + { 0, }, +}; + +static struct pci_driver cs5530_pci_driver = { + .name = DRV_NAME, + .id_table = cs5530, + .probe = cs5530_init_one, + .remove = ata_pci_remove_one +}; + +static int __init cs5530_init(void) +{ + return pci_register_driver(&cs5530_pci_driver); +} + + +static void __exit cs5530_exit(void) +{ + pci_unregister_driver(&cs5530_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Cyrix/NS/AMD 5530"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, cs5530); +MODULE_VERSION(DRV_VERSION); + +module_init(cs5530_init); +module_exit(cs5530_exit); diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c new file mode 100644 index 00000000000..d64fcdceaf0 --- /dev/null +++ b/drivers/ata/pata_cs5535.c @@ -0,0 +1,291 @@ +/* + * pata-cs5535.c - CS5535 PATA for new ATA layer + * (C) 2005-2006 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based upon cs5535.c from AMD <Jens.Altmann@amd.com> as cleaned up and + * made readable and Linux style by Wolfgang Zuleger <wolfgang.zuleger@gmx.de + * and Alexander Kiausch <alex.kiausch@t-online.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Loosely based on the piix & svwks drivers. + * + * Documentation: + * Available from AMD web site. + * TODO + * Review errata to see if serializing is neccessary + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <asm/msr.h> + +#define DRV_NAME "cs5535" +#define DRV_VERSION "0.2.10" + +/* + * The Geode (Aka Athlon GX now) uses an internal MSR based + * bus system for control. Demented but there you go. + */ + +#define MSR_ATAC_BASE 0x51300000 +#define ATAC_GLD_MSR_CAP (MSR_ATAC_BASE+0) +#define ATAC_GLD_MSR_CONFIG (MSR_ATAC_BASE+0x01) +#define ATAC_GLD_MSR_SMI (MSR_ATAC_BASE+0x02) +#define ATAC_GLD_MSR_ERROR (MSR_ATAC_BASE+0x03) +#define ATAC_GLD_MSR_PM (MSR_ATAC_BASE+0x04) +#define ATAC_GLD_MSR_DIAG (MSR_ATAC_BASE+0x05) +#define ATAC_IO_BAR (MSR_ATAC_BASE+0x08) +#define ATAC_RESET (MSR_ATAC_BASE+0x10) +#define ATAC_CH0D0_PIO (MSR_ATAC_BASE+0x20) +#define ATAC_CH0D0_DMA (MSR_ATAC_BASE+0x21) +#define ATAC_CH0D1_PIO (MSR_ATAC_BASE+0x22) +#define ATAC_CH0D1_DMA (MSR_ATAC_BASE+0x23) +#define ATAC_PCI_ABRTERR (MSR_ATAC_BASE+0x24) + +#define ATAC_BM0_CMD_PRIM 0x00 +#define ATAC_BM0_STS_PRIM 0x02 +#define ATAC_BM0_PRD 0x04 + +#define CS5535_CABLE_DETECT 0x48 + +#define CS5535_BAD_PIO(timings) ( (timings&~0x80000000UL)==0x00009172 ) + +/** + * cs5535_pre_reset - detect cable type + * @ap: Port to detect on + * + * Perform cable detection for ATA66 capable cable. Return a libata + * cable type. + */ + +static int cs5535_pre_reset(struct ata_port *ap) +{ + u8 cable; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, CS5535_CABLE_DETECT, &cable); + if (cable & 1) + ap->cbl = ATA_CBL_PATA80; + else + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * cs5535_error_handler - reset/probe + * @ap: Port to reset + * + * Reset and configure a port + */ + +static void cs5535_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, cs5535_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * cs5535_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Set our PIO requirements. The CS5535 is pretty clean about all this + */ + +static void cs5535_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const u16 pio_timings[5] = { + 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131 + }; + static const u16 pio_cmd_timings[5] = { + 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131 + }; + u32 reg, dummy; + struct ata_device *pair = ata_dev_pair(adev); + + int mode = adev->pio_mode - XFER_PIO_0; + int cmdmode = mode; + + /* Command timing has to be for the lowest of the pair of devices */ + if (pair) { + int pairmode = pair->pio_mode - XFER_PIO_0; + cmdmode = min(mode, pairmode); + /* Write the other drive timing register if it changed */ + if (cmdmode < pairmode) + wrmsr(ATAC_CH0D0_PIO + 2 * pair->devno, + pio_cmd_timings[cmdmode] << 16 | pio_timings[pairmode], 0); + } + /* Write the drive timing register */ + wrmsr(ATAC_CH0D0_PIO + 2 * adev->devno, + pio_cmd_timings[cmdmode] << 16 | pio_timings[mode], 0); + + /* Set the PIO "format 1" bit in the DMA timing register */ + rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy); + wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg | 0x80000000UL, 0); +} + +/** + * cs5535_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + */ + +static void cs5535_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const u32 udma_timings[5] = { + 0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061 + }; + static const u32 mwdma_timings[3] = { + 0x7F0FFFF3, 0x7F035352, 0x7F024241 + }; + u32 reg, dummy; + int mode = adev->dma_mode; + + rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy); + reg &= 0x80000000UL; + if (mode >= XFER_UDMA_0) + reg |= udma_timings[mode - XFER_UDMA_0]; + else + reg |= mwdma_timings[mode - XFER_MW_DMA_0]; + wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, 0); +} + +static struct scsi_host_template cs5535_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations cs5535_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cs5535_set_piomode, + .set_dmamode = cs5535_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cs5535_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * cs5535_init_one - Initialise a CS5530 + * @dev: PCI device + * @id: Entry in match table + * + * Install a driver for the newly found CS5530 companion chip. Most of + * this is just housekeeping. We have to set the chip up correctly and + * turn off various bits of emulation magic. + */ + +static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &cs5535_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, + .port_ops = &cs5535_port_ops + }; + struct ata_port_info *ports[1] = { &info }; + + u32 timings, dummy; + + /* Check the BIOS set the initial timing clock. If not set the + timings for PIO0 */ + rdmsr(ATAC_CH0D0_PIO, timings, dummy); + if (CS5535_BAD_PIO(timings)) + wrmsr(ATAC_CH0D0_PIO, 0xF7F4F7F4UL, 0); + rdmsr(ATAC_CH0D1_PIO, timings, dummy); + if (CS5535_BAD_PIO(timings)) + wrmsr(ATAC_CH0D1_PIO, 0xF7F4F7F4UL, 0); + return ata_pci_init_one(dev, ports, 1); +} + +static struct pci_device_id cs5535[] = { + { PCI_DEVICE(PCI_VENDOR_ID_NS, 0x002D), }, + { 0, }, +}; + +static struct pci_driver cs5535_pci_driver = { + .name = DRV_NAME, + .id_table = cs5535, + .probe = cs5535_init_one, + .remove = ata_pci_remove_one +}; + +static int __init cs5535_init(void) +{ + return pci_register_driver(&cs5535_pci_driver); +} + + +static void __exit cs5535_exit(void) +{ + pci_unregister_driver(&cs5535_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox, Jens Altmann, Wolfgan Zuleger, Alexander Kiausch"); +MODULE_DESCRIPTION("low-level driver for the NS/AMD 5530"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, cs5535); +MODULE_VERSION(DRV_VERSION); + +module_init(cs5535_init); +module_exit(cs5535_exit); diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c new file mode 100644 index 00000000000..dfa5ac53904 --- /dev/null +++ b/drivers/ata/pata_cypress.c @@ -0,0 +1,227 @@ +/* + * pata_cypress.c - Cypress PATA for new ATA layer + * (C) 2006 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based heavily on + * linux/drivers/ide/pci/cy82c693.c Version 0.40 Sep. 10, 2002 + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_cypress" +#define DRV_VERSION "0.1.2" + +/* here are the offset definitions for the registers */ + +enum { + CY82_IDE_CMDREG = 0x04, + CY82_IDE_ADDRSETUP = 0x48, + CY82_IDE_MASTER_IOR = 0x4C, + CY82_IDE_MASTER_IOW = 0x4D, + CY82_IDE_SLAVE_IOR = 0x4E, + CY82_IDE_SLAVE_IOW = 0x4F, + CY82_IDE_MASTER_8BIT = 0x50, + CY82_IDE_SLAVE_8BIT = 0x51, + + CY82_INDEX_PORT = 0x22, + CY82_DATA_PORT = 0x23, + + CY82_INDEX_CTRLREG1 = 0x01, + CY82_INDEX_CHANNEL0 = 0x30, + CY82_INDEX_CHANNEL1 = 0x31, + CY82_INDEX_TIMEOUT = 0x32 +}; + +static int cy82c693_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +static void cy82c693_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, cy82c693_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * cy82c693_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. + */ + +static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct ata_timing t; + const unsigned long T = 1000000 / 33; + short time_16, time_8; + u32 addr; + + if (ata_timing_compute(adev, adev->pio_mode, &t, T, 1) < 0) { + printk(KERN_ERR DRV_NAME ": mome computation failed.\n"); + return; + } + + time_16 = FIT(t.recover, 0, 15) | (FIT(t.active, 0, 15) << 4); + time_8 = FIT(t.act8b, 0, 15) | (FIT(t.rec8b, 0, 15) << 4); + + if (adev->devno == 0) { + pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr); + + addr &= ~0x0F; /* Mask bits */ + addr |= FIT(t.setup, 0, 15); + + pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr); + pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16); + pci_write_config_byte(pdev, CY82_IDE_MASTER_IOW, time_16); + pci_write_config_byte(pdev, CY82_IDE_MASTER_8BIT, time_8); + } else { + pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr); + + addr &= ~0xF0; /* Mask bits */ + addr |= (FIT(t.setup, 0, 15) << 4); + + pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr); + pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16); + pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOW, time_16); + pci_write_config_byte(pdev, CY82_IDE_SLAVE_8BIT, time_8); + } +} + +/** + * cy82c693_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the DMA mode setup. + */ + +static void cy82c693_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + int reg = CY82_INDEX_CHANNEL0 + ap->port_no; + + /* Be afraid, be very afraid. Magic registers in low I/O space */ + outb(reg, 0x22); + outb(adev->dma_mode - XFER_MW_DMA_0, 0x23); + + /* 0x50 gives the best behaviour on the Alpha's using this chip */ + outb(CY82_INDEX_TIMEOUT, 0x22); + outb(0x50, 0x23); +} + +static struct scsi_host_template cy82c693_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations cy82c693_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = cy82c693_set_piomode, + .set_dmamode = cy82c693_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = cy82c693_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &cy82c693_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &cy82c693_port_ops + }; + static struct ata_port_info *port_info[1] = { &info }; + + /* Devfn 1 is the ATA primary. The secondary is magic and on devfn2. For the + moment we don't handle the secondary. FIXME */ + + if (PCI_FUNC(pdev->devfn) != 1) + return -ENODEV; + + return ata_pci_init_one(pdev, port_info, 1); +} + +static struct pci_device_id cy82c693[] = { + { PCI_VENDOR_ID_CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { 0, }, +}; + +static struct pci_driver cy82c693_pci_driver = { + .name = DRV_NAME, + .id_table = cy82c693, + .probe = cy82c693_init_one, + .remove = ata_pci_remove_one +}; + +static int __init cy82c693_init(void) +{ + return pci_register_driver(&cy82c693_pci_driver); +} + + +static void __exit cy82c693_exit(void) +{ + pci_unregister_driver(&cy82c693_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the CY82C693 PATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, cy82c693); +MODULE_VERSION(DRV_VERSION); + +module_init(cy82c693_init); +module_exit(cy82c693_exit); diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c new file mode 100644 index 00000000000..95cd1ca181f --- /dev/null +++ b/drivers/ata/pata_efar.c @@ -0,0 +1,338 @@ +/* + * pata_efar.c - EFAR PIIX clone controller driver + * + * (C) 2005 Red Hat <alan@redhat.com> + * + * Some parts based on ata_piix.c by Jeff Garzik and others. + * + * The EFAR is a PIIX4 clone with UDMA66 support. Unlike the later + * Intel ICH controllers the EFAR widened the UDMA mode register bits + * and doesn't require the funky clock selection. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_efar" +#define DRV_VERSION "0.4.2" + +/** + * efar_pre_reset - check for 40/80 pin + * @ap: Port + * + * Perform cable detection for the EFAR ATA interface. This is + * different to the PIIX arrangement + */ + +static int efar_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits efar_enable_bits[] = { + { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ + { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 tmp; + + if (!pci_test_config_bits(pdev, &efar_enable_bits[ap->port_no])) + return -ENOENT; + + pci_read_config_byte(pdev, 0x47, &tmp); + if (tmp & (2 >> ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +/** + * efar_probe_reset - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void efar_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, efar_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * efar_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *dev = to_pci_dev(ap->host->dev); + unsigned int idetm_port= ap->port_no ? 0x42 : 0x40; + u16 idetm_data; + int control = 0; + + /* + * See Intel Document 298600-004 for the timing programing rules + * for PIIX/ICH. The EFAR is a clone so very similar + */ + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + if (pio > 2) + control |= 1; /* TIME1 enable */ + if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */ + control |= 2; /* IE enable */ + /* Intel specifies that the PPE functionality is for disk only */ + if (adev->class == ATA_DEV_ATA) + control |= 4; /* PPE enable */ + + pci_read_config_word(dev, idetm_port, &idetm_data); + + /* Enable PPE, IE and TIME as appropriate */ + + if (adev->devno == 0) { + idetm_data &= 0xCCF0; + idetm_data |= control; + idetm_data |= (timings[pio][0] << 12) | + (timings[pio][1] << 8); + } else { + int shift = 4 * ap->port_no; + u8 slave_data; + + idetm_data &= 0xCC0F; + idetm_data |= (control << 4); + + /* Slave timing in seperate register */ + pci_read_config_byte(dev, 0x44, &slave_data); + slave_data &= 0x0F << shift; + slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift; + pci_write_config_byte(dev, 0x44, slave_data); + } + + idetm_data |= 0x4000; /* Ensure SITRE is enabled */ + pci_write_config_word(dev, idetm_port, idetm_data); +} + +/** + * efar_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u8 master_port = ap->port_no ? 0x42 : 0x40; + u16 master_data; + u8 speed = adev->dma_mode; + int devid = adev->devno + 2 * ap->port_no; + u8 udma_enable; + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + pci_read_config_word(dev, master_port, &master_data); + pci_read_config_byte(dev, 0x48, &udma_enable); + + if (speed >= XFER_UDMA_0) { + unsigned int udma = adev->dma_mode - XFER_UDMA_0; + u16 udma_timing; + + udma_enable |= (1 << devid); + + /* Load the UDMA mode number */ + pci_read_config_word(dev, 0x4A, &udma_timing); + udma_timing &= ~(7 << (4 * devid)); + udma_timing |= udma << (4 * devid); + pci_write_config_word(dev, 0x4A, udma_timing); + } else { + /* + * MWDMA is driven by the PIO timings. We must also enable + * IORDY unconditionally along with TIME1. PPE has already + * been set when the PIO timing was set. + */ + unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; + unsigned int control; + u8 slave_data; + const unsigned int needed_pio[3] = { + XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 + }; + int pio = needed_pio[mwdma] - XFER_PIO_0; + + control = 3; /* IORDY|TIME1 */ + + /* If the drive MWDMA is faster than it can do PIO then + we must force PIO into PIO0 */ + + if (adev->pio_mode < needed_pio[mwdma]) + /* Enable DMA timing only */ + control |= 8; /* PIO cycles in PIO0 */ + + if (adev->devno) { /* Slave */ + master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ + master_data |= control << 4; + pci_read_config_byte(dev, 0x44, &slave_data); + slave_data &= (0x0F + 0xE1 * ap->port_no); + /* Load the matching timing */ + slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); + pci_write_config_byte(dev, 0x44, slave_data); + } else { /* Master */ + master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY + and master timing bits */ + master_data |= control; + master_data |= + (timings[pio][0] << 12) | + (timings[pio][1] << 8); + } + udma_enable &= ~(1 << devid); + pci_write_config_word(dev, master_port, master_data); + } + pci_write_config_byte(dev, 0x48, udma_enable); +} + +static struct scsi_host_template efar_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations efar_ops = { + .port_disable = ata_port_disable, + .set_piomode = efar_set_piomode, + .set_dmamode = efar_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = efar_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + + +/** + * efar_init_one - Register EFAR ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in efar_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + static struct ata_port_info info = { + .sht = &efar_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma1-2 */ + .udma_mask = 0x0f, /* UDMA 66 */ + .port_ops = &efar_ops, + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id efar_pci_tbl[] = { + { 0x1055, 0x9130, PCI_ANY_ID, PCI_ANY_ID, }, + { } /* terminate list */ +}; + +static struct pci_driver efar_pci_driver = { + .name = DRV_NAME, + .id_table = efar_pci_tbl, + .probe = efar_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init efar_init(void) +{ + return pci_register_driver(&efar_pci_driver); +} + +static void __exit efar_exit(void) +{ + pci_unregister_driver(&efar_pci_driver); +} + + +module_init(efar_init); +module_exit(efar_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for EFAR PIIX clones"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, efar_pci_tbl); +MODULE_VERSION(DRV_VERSION); + diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c new file mode 100644 index 00000000000..cf656ecbe50 --- /dev/null +++ b/drivers/ata/pata_hpt366.c @@ -0,0 +1,478 @@ +/* + * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers. + * + * This driver is heavily based upon: + * + * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 + * + * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> + * Portions Copyright (C) 2001 Sun Microsystems, Inc. + * Portions Copyright (C) 2003 Red Hat Inc + * + * + * TODO + * Maybe PLL mode + * Look into engine reset on timeout errors. Should not be + * required. + */ + + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_hpt366" +#define DRV_VERSION "0.5" + +struct hpt_clock { + u8 xfer_speed; + u32 timing; +}; + +/* key for bus clock timings + * bit + * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * register access. + * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * register access. + * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. + * during task file register access. + * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA + * xfer. + * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * register access. + * 28 UDMA enable + * 29 DMA enable + * 30 PIO_MST enable. if set, the chip is in bus master mode during + * PIO. + * 31 FIFO enable. + */ + +static const struct hpt_clock hpt366_40[] = { + { XFER_UDMA_4, 0x900fd943 }, + { XFER_UDMA_3, 0x900ad943 }, + { XFER_UDMA_2, 0x900bd943 }, + { XFER_UDMA_1, 0x9008d943 }, + { XFER_UDMA_0, 0x9008d943 }, + + { XFER_MW_DMA_2, 0xa008d943 }, + { XFER_MW_DMA_1, 0xa010d955 }, + { XFER_MW_DMA_0, 0xa010d9fc }, + + { XFER_PIO_4, 0xc008d963 }, + { XFER_PIO_3, 0xc010d974 }, + { XFER_PIO_2, 0xc010d997 }, + { XFER_PIO_1, 0xc010d9c7 }, + { XFER_PIO_0, 0xc018d9d9 }, + { 0, 0x0120d9d9 } +}; + +static const struct hpt_clock hpt366_33[] = { + { XFER_UDMA_4, 0x90c9a731 }, + { XFER_UDMA_3, 0x90cfa731 }, + { XFER_UDMA_2, 0x90caa731 }, + { XFER_UDMA_1, 0x90cba731 }, + { XFER_UDMA_0, 0x90c8a731 }, + + { XFER_MW_DMA_2, 0xa0c8a731 }, + { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */ + { XFER_MW_DMA_0, 0xa0c8a797 }, + + { XFER_PIO_4, 0xc0c8a731 }, + { XFER_PIO_3, 0xc0c8a742 }, + { XFER_PIO_2, 0xc0d0a753 }, + { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */ + { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */ + { 0, 0x0120a7a7 } +}; + +static const struct hpt_clock hpt366_25[] = { + { XFER_UDMA_4, 0x90c98521 }, + { XFER_UDMA_3, 0x90cf8521 }, + { XFER_UDMA_2, 0x90cf8521 }, + { XFER_UDMA_1, 0x90cb8521 }, + { XFER_UDMA_0, 0x90cb8521 }, + + { XFER_MW_DMA_2, 0xa0ca8521 }, + { XFER_MW_DMA_1, 0xa0ca8532 }, + { XFER_MW_DMA_0, 0xa0ca8575 }, + + { XFER_PIO_4, 0xc0ca8521 }, + { XFER_PIO_3, 0xc0ca8532 }, + { XFER_PIO_2, 0xc0ca8542 }, + { XFER_PIO_1, 0xc0d08572 }, + { XFER_PIO_0, 0xc0d08585 }, + { 0, 0x01208585 } +}; + +static const char *bad_ata33[] = { + "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2", + "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", + "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", + "Maxtor 90510D4", + "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", + "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", + "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", + NULL +}; + +static const char *bad_ata66_4[] = { + "IBM-DTLA-307075", + "IBM-DTLA-307060", + "IBM-DTLA-307045", + "IBM-DTLA-307030", + "IBM-DTLA-307020", + "IBM-DTLA-307015", + "IBM-DTLA-305040", + "IBM-DTLA-305030", + "IBM-DTLA-305020", + "IC35L010AVER07-0", + "IC35L020AVER07-0", + "IC35L030AVER07-0", + "IC35L040AVER07-0", + "IC35L060AVER07-0", + "WDC AC310200R", + NULL +}; + +static const char *bad_ata66_3[] = { + "WDC AC310200R", + NULL +}; + +static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[]) +{ + unsigned char model_num[40]; + char *s; + unsigned int len; + int i = 0; + + ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num)); + s = &model_num[0]; + len = strnlen(s, sizeof(model_num)); + + /* ATAPI specifies that empty space is blank-filled; remove blanks */ + while ((len > 0) && (s[len - 1] == ' ')) { + len--; + s[len] = 0; + } + + while(list[i] != NULL) { + if (!strncmp(list[i], s, len)) { + printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n", + modestr, list[i]); + return 1; + } + i++; + } + return 0; +} + +/** + * hpt366_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Block UDMA on devices that cause trouble with this controller. + */ + +static unsigned long hpt366_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + if (adev->class == ATA_DEV_ATA) { + if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33)) + mask &= ~ATA_MASK_UDMA; + if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3)) + mask &= ~(0x07 << ATA_SHIFT_UDMA); + if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4)) + mask &= ~(0x0F << ATA_SHIFT_UDMA); + } + return ata_pci_default_filter(ap, adev, mask); +} + +/** + * hpt36x_find_mode - reset the hpt36x bus + * @ap: ATA port + * @speed: transfer mode + * + * Return the 32bit register programming information for this channel + * that matches the speed provided. + */ + +static u32 hpt36x_find_mode(struct ata_port *ap, int speed) +{ + struct hpt_clock *clocks = ap->host->private_data; + + while(clocks->xfer_speed) { + if (clocks->xfer_speed == speed) + return clocks->timing; + clocks++; + } + BUG(); + return 0xffffffffU; /* silence compiler warning */ +} + +static int hpt36x_pre_reset(struct ata_port *ap) +{ + u8 ata66; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x5A, &ata66); + if (ata66 & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +/** + * hpt36x_error_handler - reset the hpt36x bus + * @ap: ATA port to reset + * + * Perform the reset handling for the 366/368 + */ + +static void hpt36x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, hpt36x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * hpt366_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + if (fast & 0x80) { + fast &= ~0x80; + pci_write_config_byte(pdev, addr2, fast); + } + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt36x_find_mode(ap, adev->pio_mode); + mode &= ~0x8000000; /* No FIFO in PIO */ + mode &= ~0x30070000; /* Leave config bits alone */ + reg &= 0x30070000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt366_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + if (fast & 0x80) { + fast &= ~0x80; + pci_write_config_byte(pdev, addr2, fast); + } + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt36x_find_mode(ap, adev->dma_mode); + mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ + mode &= ~0xC0000000; /* Leave config bits alone */ + reg &= 0xC0000000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +static struct scsi_host_template hpt36x_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +/* + * Configuration for HPT366/68 + */ + +static struct ata_port_operations hpt366_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt366_set_piomode, + .set_dmamode = hpt366_set_dmamode, + .mode_filter = hpt366_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt36x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * hpt36x_init_one - Initialise an HPT366/368 + * @dev: PCI device + * @id: Entry in match table + * + * Initialise an HPT36x device. There are some interesting complications + * here. Firstly the chip may report 366 and be one of several variants. + * Secondly all the timings depend on the clock for the chip which we must + * detect and look up + * + * This is the known chip mappings. It may be missing a couple of later + * releases. + * + * Chip version PCI Rev Notes + * HPT366 4 (HPT366) 0 UDMA66 + * HPT366 4 (HPT366) 1 UDMA66 + * HPT368 4 (HPT366) 2 UDMA66 + * HPT37x/30x 4 (HPT366) 3+ Other driver + * + */ + +static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info_hpt366 = { + .sht = &hpt36x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, + .port_ops = &hpt366_port_ops + }; + struct ata_port_info *port_info[2] = {&info_hpt366, &info_hpt366}; + + u32 class_rev; + u32 reg1; + u8 drive_fast; + + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xFF; + + /* May be a later chip in disguise. Check */ + /* Newer chips are not in the HPT36x driver. Ignore them */ + if (class_rev > 2) + return -ENODEV; + + pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); + pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); + pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); + + pci_read_config_byte(dev, 0x51, &drive_fast); + if (drive_fast & 0x80) + pci_write_config_byte(dev, 0x51, drive_fast & ~0x80); + + pci_read_config_dword(dev, 0x40, ®1); + + /* PCI clocking determines the ATA timing values to use */ + /* info_hpt366 is safe against re-entry so we can scribble on it */ + switch(reg1 & 0x700) { + case 5: + info_hpt366.private_data = &hpt366_40; + break; + case 9: + info_hpt366.private_data = &hpt366_25; + break; + default: + info_hpt366.private_data = &hpt366_33; + break; + } + /* Now kick off ATA set up */ + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id hpt36x[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), }, + { 0, }, +}; + +static struct pci_driver hpt36x_pci_driver = { + .name = DRV_NAME, + .id_table = hpt36x, + .probe = hpt36x_init_one, + .remove = ata_pci_remove_one +}; + +static int __init hpt36x_init(void) +{ + return pci_register_driver(&hpt36x_pci_driver); +} + + +static void __exit hpt36x_exit(void) +{ + pci_unregister_driver(&hpt36x_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, hpt36x); +MODULE_VERSION(DRV_VERSION); + +module_init(hpt36x_init); +module_exit(hpt36x_exit); diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c new file mode 100644 index 00000000000..10318c0012e --- /dev/null +++ b/drivers/ata/pata_hpt37x.c @@ -0,0 +1,1257 @@ +/* + * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers. + * + * This driver is heavily based upon: + * + * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 + * + * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> + * Portions Copyright (C) 2001 Sun Microsystems, Inc. + * Portions Copyright (C) 2003 Red Hat Inc + * + * TODO + * PLL mode + * Look into engine reset on timeout errors. Should not be + * required. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_hpt37x" +#define DRV_VERSION "0.5" + +struct hpt_clock { + u8 xfer_speed; + u32 timing; +}; + +struct hpt_chip { + const char *name; + unsigned int base; + struct hpt_clock const *clocks[4]; +}; + +/* key for bus clock timings + * bit + * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * register access. + * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * register access. + * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. + * during task file register access. + * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA + * xfer. + * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * register access. + * 28 UDMA enable + * 29 DMA enable + * 30 PIO_MST enable. if set, the chip is in bus master mode during + * PIO. + * 31 FIFO enable. + */ + +/* from highpoint documentation. these are old values */ +static const struct hpt_clock hpt370_timings_33[] = { +/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */ + { XFER_UDMA_5, 0x16454e31 }, + { XFER_UDMA_4, 0x16454e31 }, + { XFER_UDMA_3, 0x166d4e31 }, + { XFER_UDMA_2, 0x16494e31 }, + { XFER_UDMA_1, 0x164d4e31 }, + { XFER_UDMA_0, 0x16514e31 }, + + { XFER_MW_DMA_2, 0x26514e21 }, + { XFER_MW_DMA_1, 0x26514e33 }, + { XFER_MW_DMA_0, 0x26514e97 }, + + { XFER_PIO_4, 0x06514e21 }, + { XFER_PIO_3, 0x06514e22 }, + { XFER_PIO_2, 0x06514e33 }, + { XFER_PIO_1, 0x06914e43 }, + { XFER_PIO_0, 0x06914e57 }, + { 0, 0x06514e57 } +}; + +static const struct hpt_clock hpt370_timings_66[] = { + { XFER_UDMA_5, 0x14846231 }, + { XFER_UDMA_4, 0x14886231 }, + { XFER_UDMA_3, 0x148c6231 }, + { XFER_UDMA_2, 0x148c6231 }, + { XFER_UDMA_1, 0x14906231 }, + { XFER_UDMA_0, 0x14986231 }, + + { XFER_MW_DMA_2, 0x26514e21 }, + { XFER_MW_DMA_1, 0x26514e33 }, + { XFER_MW_DMA_0, 0x26514e97 }, + + { XFER_PIO_4, 0x06514e21 }, + { XFER_PIO_3, 0x06514e22 }, + { XFER_PIO_2, 0x06514e33 }, + { XFER_PIO_1, 0x06914e43 }, + { XFER_PIO_0, 0x06914e57 }, + { 0, 0x06514e57 } +}; + +/* these are the current (4 sep 2001) timings from highpoint */ +static const struct hpt_clock hpt370a_timings_33[] = { + { XFER_UDMA_5, 0x12446231 }, + { XFER_UDMA_4, 0x12446231 }, + { XFER_UDMA_3, 0x126c6231 }, + { XFER_UDMA_2, 0x12486231 }, + { XFER_UDMA_1, 0x124c6233 }, + { XFER_UDMA_0, 0x12506297 }, + + { XFER_MW_DMA_2, 0x22406c31 }, + { XFER_MW_DMA_1, 0x22406c33 }, + { XFER_MW_DMA_0, 0x22406c97 }, + + { XFER_PIO_4, 0x06414e31 }, + { XFER_PIO_3, 0x06414e42 }, + { XFER_PIO_2, 0x06414e53 }, + { XFER_PIO_1, 0x06814e93 }, + { XFER_PIO_0, 0x06814ea7 }, + { 0, 0x06814ea7 } +}; + +/* 2x 33MHz timings */ +static const struct hpt_clock hpt370a_timings_66[] = { + { XFER_UDMA_5, 0x1488e673 }, + { XFER_UDMA_4, 0x1488e673 }, + { XFER_UDMA_3, 0x1498e673 }, + { XFER_UDMA_2, 0x1490e673 }, + { XFER_UDMA_1, 0x1498e677 }, + { XFER_UDMA_0, 0x14a0e73f }, + + { XFER_MW_DMA_2, 0x2480fa73 }, + { XFER_MW_DMA_1, 0x2480fa77 }, + { XFER_MW_DMA_0, 0x2480fb3f }, + + { XFER_PIO_4, 0x0c82be73 }, + { XFER_PIO_3, 0x0c82be95 }, + { XFER_PIO_2, 0x0c82beb7 }, + { XFER_PIO_1, 0x0d02bf37 }, + { XFER_PIO_0, 0x0d02bf5f }, + { 0, 0x0d02bf5f } +}; + +static const struct hpt_clock hpt370a_timings_50[] = { + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x0ac1f48a } +}; + +static const struct hpt_clock hpt372_timings_33[] = { + { XFER_UDMA_6, 0x1c81dc62 }, + { XFER_UDMA_5, 0x1c6ddc62 }, + { XFER_UDMA_4, 0x1c8ddc62 }, + { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */ + { XFER_UDMA_2, 0x1c91dc62 }, + { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */ + { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */ + + { XFER_MW_DMA_2, 0x2c829262 }, + { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */ + { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */ + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d5e } +}; + +static const struct hpt_clock hpt372_timings_50[] = { + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x0a81f443 } +}; + +static const struct hpt_clock hpt372_timings_66[] = { + { XFER_UDMA_6, 0x1c869c62 }, + { XFER_UDMA_5, 0x1cae9c62 }, + { XFER_UDMA_4, 0x1c8a9c62 }, + { XFER_UDMA_3, 0x1c8e9c62 }, + { XFER_UDMA_2, 0x1c929c62 }, + { XFER_UDMA_1, 0x1c9a9c62 }, + { XFER_UDMA_0, 0x1c829c62 }, + + { XFER_MW_DMA_2, 0x2c829c62 }, + { XFER_MW_DMA_1, 0x2c829c66 }, + { XFER_MW_DMA_0, 0x2c829d2e }, + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d26 } +}; + +static const struct hpt_clock hpt374_timings_33[] = { + { XFER_UDMA_6, 0x12808242 }, + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x06814e93 } +}; + +static const struct hpt_chip hpt370 = { + "HPT370", + 48, + { + hpt370_timings_33, + NULL, + NULL, + hpt370_timings_66 + } +}; + +static const struct hpt_chip hpt370a = { + "HPT370A", + 48, + { + hpt370a_timings_33, + NULL, + hpt370a_timings_50, + hpt370a_timings_66 + } +}; + +static const struct hpt_chip hpt372 = { + "HPT372", + 55, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt302 = { + "HPT302", + 66, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt371 = { + "HPT371", + 66, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt372a = { + "HPT372A", + 66, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt374 = { + "HPT374", + 48, + { + hpt374_timings_33, + NULL, + NULL, + NULL + } +}; + +/** + * hpt37x_find_mode - reset the hpt37x bus + * @ap: ATA port + * @speed: transfer mode + * + * Return the 32bit register programming information for this channel + * that matches the speed provided. + */ + +static u32 hpt37x_find_mode(struct ata_port *ap, int speed) +{ + struct hpt_clock *clocks = ap->host->private_data; + + while(clocks->xfer_speed) { + if (clocks->xfer_speed == speed) + return clocks->timing; + clocks++; + } + BUG(); + return 0xffffffffU; /* silence compiler warning */ +} + +static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[]) +{ + unsigned char model_num[40]; + char *s; + unsigned int len; + int i = 0; + + ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS, + sizeof(model_num)); + s = &model_num[0]; + len = strnlen(s, sizeof(model_num)); + + /* ATAPI specifies that empty space is blank-filled; remove blanks */ + while ((len > 0) && (s[len - 1] == ' ')) { + len--; + s[len] = 0; + } + + while(list[i] != NULL) { + if (!strncmp(list[i], s, len)) { + printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n", + modestr, list[i]); + return 1; + } + i++; + } + return 0; +} + +static const char *bad_ata33[] = { + "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2", + "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", + "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", + "Maxtor 90510D4", + "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", + "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", + "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", + NULL +}; + +static const char *bad_ata100_5[] = { + "IBM-DTLA-307075", + "IBM-DTLA-307060", + "IBM-DTLA-307045", + "IBM-DTLA-307030", + "IBM-DTLA-307020", + "IBM-DTLA-307015", + "IBM-DTLA-305040", + "IBM-DTLA-305030", + "IBM-DTLA-305020", + "IC35L010AVER07-0", + "IC35L020AVER07-0", + "IC35L030AVER07-0", + "IC35L040AVER07-0", + "IC35L060AVER07-0", + "WDC AC310200R", + NULL +}; + +/** + * hpt370_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Block UDMA on devices that cause trouble with this controller. + */ + +static unsigned long hpt370_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + if (adev->class != ATA_DEV_ATA) { + if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33)) + mask &= ~ATA_MASK_UDMA; + if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) + mask &= ~(0x1F << ATA_SHIFT_UDMA); + } + return ata_pci_default_filter(ap, adev, mask); +} + +/** + * hpt370a_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Block UDMA on devices that cause trouble with this controller. + */ + +static unsigned long hpt370a_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + if (adev->class != ATA_DEV_ATA) { + if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) + mask &= ~ (0x1F << ATA_SHIFT_UDMA); + } + return ata_pci_default_filter(ap, adev, mask); +} + +/** + * hpt37x_pre_reset - reset the hpt37x bus + * @ap: ATA port to reset + * + * Perform the initial reset handling for the 370/372 and 374 func 0 + */ + +static int hpt37x_pre_reset(struct ata_port *ap) +{ + u8 scr2, ata66; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x5B, &scr2); + pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); + /* Cable register now active */ + pci_read_config_byte(pdev, 0x5A, &ata66); + /* Restore state */ + pci_write_config_byte(pdev, 0x5B, scr2); + + if (ata66 & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + /* Reset the state machine */ + pci_write_config_byte(pdev, 0x50, 0x37); + pci_write_config_byte(pdev, 0x54, 0x37); + udelay(100); + + return ata_std_prereset(ap); +} + +/** + * hpt37x_error_handler - reset the hpt374 + * @ap: ATA port to reset + * + * Perform probe for HPT37x, except for HPT374 channel 2 + */ + +static void hpt37x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +static int hpt374_pre_reset(struct ata_port *ap) +{ + u16 mcr3, mcr6; + u8 ata66; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + /* Do the extra channel work */ + pci_read_config_word(pdev, 0x52, &mcr3); + pci_read_config_word(pdev, 0x56, &mcr6); + /* Set bit 15 of 0x52 to enable TCBLID as input + Set bit 15 of 0x56 to enable FCBLID as input + */ + pci_write_config_word(pdev, 0x52, mcr3 | 0x8000); + pci_write_config_word(pdev, 0x56, mcr6 | 0x8000); + pci_read_config_byte(pdev, 0x5A, &ata66); + /* Reset TCBLID/FCBLID to output */ + pci_write_config_word(pdev, 0x52, mcr3); + pci_write_config_word(pdev, 0x56, mcr6); + + if (ata66 & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + /* Reset the state machine */ + pci_write_config_byte(pdev, 0x50, 0x37); + pci_write_config_byte(pdev, 0x54, 0x37); + udelay(100); + + return ata_std_prereset(ap); +} + +/** + * hpt374_error_handler - reset the hpt374 + * @classes: + * + * The 374 cable detect is a little different due to the extra + * channels. The function 0 channels work like usual but function 1 + * is special + */ + +static void hpt374_error_handler(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!(PCI_FUNC(pdev->devfn) & 1)) + hpt37x_error_handler(ap); + else + ata_bmdma_drive_eh(ap, hpt374_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * hpt370_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x02; + fast |= 0x01; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->pio_mode); + mode &= ~0x8000000; /* No FIFO in PIO */ + mode &= ~0x30070000; /* Leave config bits alone */ + reg &= 0x30070000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt370_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x02; + fast |= 0x01; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->dma_mode); + mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ + mode &= ~0xC0000000; /* Leave config bits alone */ + reg &= 0xC0000000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt370_bmdma_start - DMA engine begin + * @qc: ATA command + * + * The 370 and 370A want us to reset the DMA engine each time we + * use it. The 372 and later are fine. + */ + +static void hpt370_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); + udelay(10); + ata_bmdma_start(qc); +} + +/** + * hpt370_bmdma_end - DMA engine stop + * @qc: ATA command + * + * Work around the HPT370 DMA engine. + */ + +static void hpt370_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 dma_stat = inb(ap->ioaddr.bmdma_addr + 2); + u8 dma_cmd; + unsigned long bmdma = ap->ioaddr.bmdma_addr; + + if (dma_stat & 0x01) { + udelay(20); + dma_stat = inb(bmdma + 2); + } + if (dma_stat & 0x01) { + /* Clear the engine */ + pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); + udelay(10); + /* Stop DMA */ + dma_cmd = inb(bmdma ); + outb(dma_cmd & 0xFE, bmdma); + /* Clear Error */ + dma_stat = inb(bmdma + 2); + outb(dma_stat | 0x06 , bmdma + 2); + /* Clear the engine */ + pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); + udelay(10); + } + ata_bmdma_stop(qc); +} + +/** + * hpt372_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->pio_mode); + + printk("Find mode for %d reports %X\n", adev->pio_mode, mode); + mode &= ~0x80000000; /* No FIFO in PIO */ + mode &= ~0x30070000; /* Leave config bits alone */ + reg &= 0x30070000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt372_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->dma_mode); + printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode); + mode &= ~0xC0000000; /* Leave config bits alone */ + mode |= 0x80000000; /* FIFO in MWDMA or UDMA */ + reg &= 0xC0000000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt37x_bmdma_end - DMA engine stop + * @qc: ATA command + * + * Clean up after the HPT372 and later DMA engine + */ + +static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int mscreg = 0x50 + 2 * ap->port_no; + u8 bwsr_stat, msc_stat; + + pci_read_config_byte(pdev, 0x6A, &bwsr_stat); + pci_read_config_byte(pdev, mscreg, &msc_stat); + if (bwsr_stat & (1 << ap->port_no)) + pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); + ata_bmdma_stop(qc); +} + + +static struct scsi_host_template hpt37x_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +/* + * Configuration for HPT370 + */ + +static struct ata_port_operations hpt370_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt370_set_piomode, + .set_dmamode = hpt370_set_dmamode, + .mode_filter = hpt370_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt37x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = hpt370_bmdma_start, + .bmdma_stop = hpt370_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Configuration for HPT370A. Close to 370 but less filters + */ + +static struct ata_port_operations hpt370a_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt370_set_piomode, + .set_dmamode = hpt370_set_dmamode, + .mode_filter = hpt370a_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt37x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = hpt370_bmdma_start, + .bmdma_stop = hpt370_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Configuration for HPT372, HPT371, HPT302. Slightly different PIO + * and DMA mode setting functionality. + */ + +static struct ata_port_operations hpt372_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt372_set_piomode, + .set_dmamode = hpt372_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt37x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = hpt37x_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Configuration for HPT374. Mode setting works like 372 and friends + * but we have a different cable detection procedure. + */ + +static struct ata_port_operations hpt374_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt372_set_piomode, + .set_dmamode = hpt372_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt374_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = hpt37x_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * htp37x_clock_slot - Turn timing to PC clock entry + * @freq: Reported frequency timing + * @base: Base timing + * + * Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50 + * and 3 for 66Mhz) + */ + +static int hpt37x_clock_slot(unsigned int freq, unsigned int base) +{ + unsigned int f = (base * freq) / 192; /* Mhz */ + if (f < 40) + return 0; /* 33Mhz slot */ + if (f < 45) + return 1; /* 40Mhz slot */ + if (f < 55) + return 2; /* 50Mhz slot */ + return 3; /* 60Mhz slot */ +} + +/** + * hpt37x_calibrate_dpll - Calibrate the DPLL loop + * @dev: PCI device + * + * Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this + * succeeds + */ + +static int hpt37x_calibrate_dpll(struct pci_dev *dev) +{ + u8 reg5b; + u32 reg5c; + int tries; + + for(tries = 0; tries < 0x5000; tries++) { + udelay(50); + pci_read_config_byte(dev, 0x5b, ®5b); + if (reg5b & 0x80) { + /* See if it stays set */ + for(tries = 0; tries < 0x1000; tries ++) { + pci_read_config_byte(dev, 0x5b, ®5b); + /* Failed ? */ + if ((reg5b & 0x80) == 0) + return 0; + } + /* Turn off tuning, we have the DPLL set */ + pci_read_config_dword(dev, 0x5c, ®5c); + pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100); + return 1; + } + } + /* Never went stable */ + return 0; +} +/** + * hpt37x_init_one - Initialise an HPT37X/302 + * @dev: PCI device + * @id: Entry in match table + * + * Initialise an HPT37x device. There are some interesting complications + * here. Firstly the chip may report 366 and be one of several variants. + * Secondly all the timings depend on the clock for the chip which we must + * detect and look up + * + * This is the known chip mappings. It may be missing a couple of later + * releases. + * + * Chip version PCI Rev Notes + * HPT366 4 (HPT366) 0 Other driver + * HPT366 4 (HPT366) 1 Other driver + * HPT368 4 (HPT366) 2 Other driver + * HPT370 4 (HPT366) 3 UDMA100 + * HPT370A 4 (HPT366) 4 UDMA100 + * HPT372 4 (HPT366) 5 UDMA133 (1) + * HPT372N 4 (HPT366) 6 Other driver + * HPT372A 5 (HPT372) 1 UDMA133 (1) + * HPT372N 5 (HPT372) 2 Other driver + * HPT302 6 (HPT302) 1 UDMA133 + * HPT302N 6 (HPT302) 2 Other driver + * HPT371 7 (HPT371) * UDMA133 + * HPT374 8 (HPT374) * UDMA133 4 channel + * HPT372N 9 (HPT372N) * Other driver + * + * (1) UDMA133 support depends on the bus clock + */ + +static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + /* HPT370 - UDMA100 */ + static struct ata_port_info info_hpt370 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &hpt370_port_ops + }; + /* HPT370A - UDMA100 */ + static struct ata_port_info info_hpt370a = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &hpt370a_port_ops + }; + /* HPT371, 372 and friends - UDMA133 */ + static struct ata_port_info info_hpt372 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &hpt372_port_ops + }; + /* HPT371, 372 and friends - UDMA100 at 50MHz clock */ + static struct ata_port_info info_hpt372_50 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &hpt372_port_ops + }; + /* HPT374 - UDMA133 */ + static struct ata_port_info info_hpt374 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &hpt374_port_ops + }; + + static const int MHz[4] = { 33, 40, 50, 66 }; + + struct ata_port_info *port_info[2]; + struct ata_port_info *port; + + u8 irqmask; + u32 class_rev; + u32 freq; + + const struct hpt_chip *chip_table; + int clock_slot; + + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xFF; + + if (dev->device == PCI_DEVICE_ID_TTI_HPT366) { + /* May be a later chip in disguise. Check */ + /* Older chips are in the HPT366 driver. Ignore them */ + if (class_rev < 3) + return -ENODEV; + /* N series chips have their own driver. Ignore */ + if (class_rev == 6) + return -ENODEV; + + switch(class_rev) { + case 3: + port = &info_hpt370; + chip_table = &hpt370; + break; + case 4: + port = &info_hpt370a; + chip_table = &hpt370a; + break; + case 5: + port = &info_hpt372; + chip_table = &hpt372; + break; + default: + printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype please report (%d).\n", class_rev); + return -ENODEV; + } + } else { + switch(dev->device) { + case PCI_DEVICE_ID_TTI_HPT372: + /* 372N if rev >= 2*/ + if (class_rev >= 2) + return -ENODEV; + port = &info_hpt372; + chip_table = &hpt372a; + break; + case PCI_DEVICE_ID_TTI_HPT302: + /* 302N if rev > 1 */ + if (class_rev > 1) + return -ENODEV; + port = &info_hpt372; + /* Check this */ + chip_table = &hpt302; + break; + case PCI_DEVICE_ID_TTI_HPT371: + port = &info_hpt372; + chip_table = &hpt371; + break; + case PCI_DEVICE_ID_TTI_HPT374: + chip_table = &hpt374; + port = &info_hpt374; + break; + default: + printk(KERN_ERR "pata_hpt37x: PCI table is bogus please report (%d).\n", dev->device); + return -ENODEV; + } + } + /* Ok so this is a chip we support */ + + pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); + pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); + pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); + + pci_read_config_byte(dev, 0x5A, &irqmask); + irqmask &= ~0x10; + pci_write_config_byte(dev, 0x5a, irqmask); + + /* + * default to pci clock. make sure MA15/16 are set to output + * to prevent drives having problems with 40-pin cables. Needed + * for some drives such as IBM-DTLA which will not enter ready + * state on reset when PDIAG is a input. + */ + + pci_write_config_byte(dev, 0x5b, 0x23); + + pci_read_config_dword(dev, 0x70, &freq); + if ((freq >> 12) != 0xABCDE) { + int i; + u8 sr; + u32 total = 0; + + printk(KERN_WARNING "pata_hpt37x: BIOS has not set timing clocks.\n"); + + /* This is the process the HPT371 BIOS is reported to use */ + for(i = 0; i < 128; i++) { + pci_read_config_byte(dev, 0x78, &sr); + total += sr; + udelay(15); + } + freq = total / 128; + } + freq &= 0x1FF; + + /* + * Turn the frequency check into a band and then find a timing + * table to match it. + */ + + clock_slot = hpt37x_clock_slot(freq, chip_table->base); + if (chip_table->clocks[clock_slot] == NULL) { + /* + * We need to try PLL mode instead + */ + unsigned int f_low = (MHz[clock_slot] * chip_table->base) / 192; + unsigned int f_high = f_low + 2; + int adjust; + + for(adjust = 0; adjust < 8; adjust++) { + if (hpt37x_calibrate_dpll(dev)) + break; + /* See if it'll settle at a fractionally different clock */ + if ((adjust & 3) == 3) { + f_low --; + f_high ++; + } + pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low); + } + if (adjust == 8) { + printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n"); + return -ENODEV; + } + /* Check if this works for all cases */ + port->private_data = (void *)hpt370_timings_66; + + printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]); + } else { + port->private_data = (void *)chip_table->clocks[clock_slot]; + /* + * Perform a final fixup. The 371 and 372 clock determines + * if UDMA133 is available. + */ + + if (clock_slot == 2 && chip_table == &hpt372) { /* 50Mhz */ + printk(KERN_WARNING "pata_hpt37x: No UDMA133 support available with 50MHz bus clock.\n"); + if (port == &info_hpt372) + port = &info_hpt372_50; + else BUG(); + } + printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]); + } + port_info[0] = port_info[1] = port; + /* Now kick off ATA set up */ + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id hpt37x[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), }, + { 0, }, +}; + +static struct pci_driver hpt37x_pci_driver = { + .name = DRV_NAME, + .id_table = hpt37x, + .probe = hpt37x_init_one, + .remove = ata_pci_remove_one +}; + +static int __init hpt37x_init(void) +{ + return pci_register_driver(&hpt37x_pci_driver); +} + + +static void __exit hpt37x_exit(void) +{ + pci_unregister_driver(&hpt37x_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, hpt37x); +MODULE_VERSION(DRV_VERSION); + +module_init(hpt37x_init); +module_exit(hpt37x_exit); diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c new file mode 100644 index 00000000000..5c5d4f6ab90 --- /dev/null +++ b/drivers/ata/pata_hpt3x2n.c @@ -0,0 +1,597 @@ +/* + * Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers. + * + * This driver is heavily based upon: + * + * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 + * + * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> + * Portions Copyright (C) 2001 Sun Microsystems, Inc. + * Portions Copyright (C) 2003 Red Hat Inc + * + * + * TODO + * 371N + * Work out best PLL policy + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_hpt3x2n" +#define DRV_VERSION "0.3" + +enum { + HPT_PCI_FAST = (1 << 31), + PCI66 = (1 << 1), + USE_DPLL = (1 << 0) +}; + +struct hpt_clock { + u8 xfer_speed; + u32 timing; +}; + +struct hpt_chip { + const char *name; + struct hpt_clock *clocks[3]; +}; + +/* key for bus clock timings + * bit + * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * register access. + * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * register access. + * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. + * during task file register access. + * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA + * xfer. + * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * register access. + * 28 UDMA enable + * 29 DMA enable + * 30 PIO_MST enable. if set, the chip is in bus master mode during + * PIO. + * 31 FIFO enable. + */ + +/* 66MHz DPLL clocks */ + +static struct hpt_clock hpt3x2n_clocks[] = { + { XFER_UDMA_7, 0x1c869c62 }, + { XFER_UDMA_6, 0x1c869c62 }, + { XFER_UDMA_5, 0x1c8a9c62 }, + { XFER_UDMA_4, 0x1c8a9c62 }, + { XFER_UDMA_3, 0x1c8e9c62 }, + { XFER_UDMA_2, 0x1c929c62 }, + { XFER_UDMA_1, 0x1c9a9c62 }, + { XFER_UDMA_0, 0x1c829c62 }, + + { XFER_MW_DMA_2, 0x2c829c62 }, + { XFER_MW_DMA_1, 0x2c829c66 }, + { XFER_MW_DMA_0, 0x2c829d2c }, + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d5e } +}; + +/** + * hpt3x2n_find_mode - reset the hpt3x2n bus + * @ap: ATA port + * @speed: transfer mode + * + * Return the 32bit register programming information for this channel + * that matches the speed provided. For the moment the clocks table + * is hard coded but easy to change. This will be needed if we use + * different DPLLs + */ + +static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed) +{ + struct hpt_clock *clocks = hpt3x2n_clocks; + + while(clocks->xfer_speed) { + if (clocks->xfer_speed == speed) + return clocks->timing; + clocks++; + } + BUG(); + return 0xffffffffU; /* silence compiler warning */ +} + +/** + * hpt3x2n_pre_reset - reset the hpt3x2n bus + * @ap: ATA port to reset + * + * Perform the initial reset handling for the 3x2n series controllers. + * Reset the hardware and state machine, obtain the cable type. + */ + +static int hpt3xn_pre_reset(struct ata_port *ap) +{ + u8 scr2, ata66; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x5B, &scr2); + pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); + /* Cable register now active */ + pci_read_config_byte(pdev, 0x5A, &ata66); + /* Restore state */ + pci_write_config_byte(pdev, 0x5B, scr2); + + if (ata66 & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + /* Reset the state machine */ + pci_write_config_byte(pdev, 0x50, 0x37); + pci_write_config_byte(pdev, 0x54, 0x37); + udelay(100); + + return ata_std_prereset(ap); +} + +/** + * hpt3x2n_error_handler - probe the hpt3x2n bus + * @ap: ATA port to reset + * + * Perform the probe reset handling for the 3x2N + */ + +static void hpt3x2n_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * hpt3x2n_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt3x2n_find_mode(ap, adev->pio_mode); + mode &= ~0x8000000; /* No FIFO in PIO */ + mode &= ~0x30070000; /* Leave config bits alone */ + reg &= 0x30070000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt3x2n_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt3x2n_find_mode(ap, adev->dma_mode); + mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ + mode &= ~0xC0000000; /* Leave config bits alone */ + reg &= 0xC0000000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt3x2n_bmdma_end - DMA engine stop + * @qc: ATA command + * + * Clean up after the HPT3x2n and later DMA engine + */ + +static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int mscreg = 0x50 + 2 * ap->port_no; + u8 bwsr_stat, msc_stat; + + pci_read_config_byte(pdev, 0x6A, &bwsr_stat); + pci_read_config_byte(pdev, mscreg, &msc_stat); + if (bwsr_stat & (1 << ap->port_no)) + pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); + ata_bmdma_stop(qc); +} + +/** + * hpt3x2n_set_clock - clock control + * @ap: ATA port + * @source: 0x21 or 0x23 for PLL or PCI sourced clock + * + * Switch the ATA bus clock between the PLL and PCI clock sources + * while correctly isolating the bus and resetting internal logic + * + * We must use the DPLL for + * - writing + * - second channel UDMA7 (SATA ports) or higher + * - 66MHz PCI + * + * or we will underclock the device and get reduced performance. + */ + +static void hpt3x2n_set_clock(struct ata_port *ap, int source) +{ + unsigned long bmdma = ap->ioaddr.bmdma_addr; + + /* Tristate the bus */ + outb(0x80, bmdma+0x73); + outb(0x80, bmdma+0x77); + + /* Switch clock and reset channels */ + outb(source, bmdma+0x7B); + outb(0xC0, bmdma+0x79); + + /* Reset state machines */ + outb(0x37, bmdma+0x70); + outb(0x37, bmdma+0x74); + + /* Complete reset */ + outb(0x00, bmdma+0x79); + + /* Reconnect channels to bus */ + outb(0x00, bmdma+0x73); + outb(0x00, bmdma+0x77); +} + +/* Check if our partner interface is busy */ + +static int hpt3x2n_pair_idle(struct ata_port *ap) +{ + struct ata_host *host = ap->host; + struct ata_port *pair = host->ports[ap->port_no ^ 1]; + + if (pair->hsm_task_state == HSM_ST_IDLE) + return 1; + return 0; +} + +static int hpt3x2n_use_dpll(struct ata_port *ap, int reading) +{ + long flags = (long)ap->host->private_data; + /* See if we should use the DPLL */ + if (reading == 0) + return USE_DPLL; /* Needed for write */ + if (flags & PCI66) + return USE_DPLL; /* Needed at 66Mhz */ + return 0; +} + +static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_taskfile *tf = &qc->tf; + struct ata_port *ap = qc->ap; + int flags = (long)ap->host->private_data; + + if (hpt3x2n_pair_idle(ap)) { + int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE)); + if ((flags & USE_DPLL) != dpll) { + if (dpll == 1) + hpt3x2n_set_clock(ap, 0x21); + else + hpt3x2n_set_clock(ap, 0x23); + } + } + return ata_qc_issue_prot(qc); +} + +static struct scsi_host_template hpt3x2n_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +/* + * Configuration for HPT3x2n. + */ + +static struct ata_port_operations hpt3x2n_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt3x2n_set_piomode, + .set_dmamode = hpt3x2n_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt3x2n_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = hpt3x2n_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = hpt3x2n_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * hpt3xn_calibrate_dpll - Calibrate the DPLL loop + * @dev: PCI device + * + * Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this + * succeeds + */ + +static int hpt3xn_calibrate_dpll(struct pci_dev *dev) +{ + u8 reg5b; + u32 reg5c; + int tries; + + for(tries = 0; tries < 0x5000; tries++) { + udelay(50); + pci_read_config_byte(dev, 0x5b, ®5b); + if (reg5b & 0x80) { + /* See if it stays set */ + for(tries = 0; tries < 0x1000; tries ++) { + pci_read_config_byte(dev, 0x5b, ®5b); + /* Failed ? */ + if ((reg5b & 0x80) == 0) + return 0; + } + /* Turn off tuning, we have the DPLL set */ + pci_read_config_dword(dev, 0x5c, ®5c); + pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100); + return 1; + } + } + /* Never went stable */ + return 0; +} + +static int hpt3x2n_pci_clock(struct pci_dev *pdev) +{ + unsigned long freq; + u32 fcnt; + + pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt); + if ((fcnt >> 12) != 0xABCDE) { + printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n"); + return 33; /* Not BIOS set */ + } + fcnt &= 0x1FF; + + freq = (fcnt * 77) / 192; + + /* Clamp to bands */ + if (freq < 40) + return 33; + if (freq < 45) + return 40; + if (freq < 55) + return 50; + return 66; +} + +/** + * hpt3x2n_init_one - Initialise an HPT37X/302 + * @dev: PCI device + * @id: Entry in match table + * + * Initialise an HPT3x2n device. There are some interesting complications + * here. Firstly the chip may report 366 and be one of several variants. + * Secondly all the timings depend on the clock for the chip which we must + * detect and look up + * + * This is the known chip mappings. It may be missing a couple of later + * releases. + * + * Chip version PCI Rev Notes + * HPT372 4 (HPT366) 5 Other driver + * HPT372N 4 (HPT366) 6 UDMA133 + * HPT372 5 (HPT372) 1 Other driver + * HPT372N 5 (HPT372) 2 UDMA133 + * HPT302 6 (HPT302) * Other driver + * HPT302N 6 (HPT302) > 1 UDMA133 + * HPT371 7 (HPT371) * Other driver + * HPT371N 7 (HPT371) > 1 UDMA133 + * HPT374 8 (HPT374) * Other driver + * HPT372N 9 (HPT372N) * UDMA133 + * + * (1) UDMA133 support depends on the bus clock + * + * To pin down HPT371N + */ + +static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + /* HPT372N and friends - UDMA133 */ + static struct ata_port_info info = { + .sht = &hpt3x2n_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &hpt3x2n_port_ops + }; + struct ata_port_info *port_info[2]; + struct ata_port_info *port = &info; + + u8 irqmask; + u32 class_rev; + + unsigned int pci_mhz; + unsigned int f_low, f_high; + int adjust; + + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xFF; + + switch(dev->device) { + case PCI_DEVICE_ID_TTI_HPT366: + if (class_rev < 6) + return -ENODEV; + break; + case PCI_DEVICE_ID_TTI_HPT372: + /* 372N if rev >= 1*/ + if (class_rev == 0) + return -ENODEV; + break; + case PCI_DEVICE_ID_TTI_HPT302: + if (class_rev < 2) + return -ENODEV; + break; + case PCI_DEVICE_ID_TTI_HPT372N: + break; + default: + printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device); + return -ENODEV; + } + + /* Ok so this is a chip we support */ + + pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); + pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); + pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); + + pci_read_config_byte(dev, 0x5A, &irqmask); + irqmask &= ~0x10; + pci_write_config_byte(dev, 0x5a, irqmask); + + /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or + 50 for UDMA100. Right now we always use 66 */ + + pci_mhz = hpt3x2n_pci_clock(dev); + + f_low = (pci_mhz * 48) / 66; /* PCI Mhz for 66Mhz DPLL */ + f_high = f_low + 2; /* Tolerance */ + + pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100); + /* PLL clock */ + pci_write_config_byte(dev, 0x5B, 0x21); + + /* Unlike the 37x we don't try jiggling the frequency */ + for(adjust = 0; adjust < 8; adjust++) { + if (hpt3xn_calibrate_dpll(dev)) + break; + pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low); + } + if (adjust == 8) + printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n"); + + /* Set our private data up. We only need a few flags so we use + it directly */ + port->private_data = NULL; + if (pci_mhz > 60) + port->private_data = (void *)PCI66; + + /* Now kick off ATA set up */ + port_info[0] = port_info[1] = port; + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id hpt3x2n[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N), }, + { 0, }, +}; + +static struct pci_driver hpt3x2n_pci_driver = { + .name = DRV_NAME, + .id_table = hpt3x2n, + .probe = hpt3x2n_init_one, + .remove = ata_pci_remove_one +}; + +static int __init hpt3x2n_init(void) +{ + return pci_register_driver(&hpt3x2n_pci_driver); +} + + +static void __exit hpt3x2n_exit(void) +{ + pci_unregister_driver(&hpt3x2n_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, hpt3x2n); +MODULE_VERSION(DRV_VERSION); + +module_init(hpt3x2n_init); +module_exit(hpt3x2n_exit); diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c new file mode 100644 index 00000000000..1f084ab1ccc --- /dev/null +++ b/drivers/ata/pata_hpt3x3.c @@ -0,0 +1,226 @@ +/* + * pata_hpt3x3 - HPT3x3 driver + * (c) Copyright 2005-2006 Red Hat + * + * Was pata_hpt34x but the naming was confusing as it supported the + * 343 and 363 so it has been renamed. + * + * Based on: + * linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002 + * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> + * + * May be copied or modified under the terms of the GNU General Public + * License + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_hpt3x3" +#define DRV_VERSION "0.4.1" + +static int hpt3x3_probe_init(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * hpt3x3_probe_reset - reset the hpt3x3 bus + * @ap: ATA port to reset + * + * Perform the housekeeping when doing an ATA bus reeset. We just + * need to force the cable type. + */ + +static void hpt3x3_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, hpt3x3_probe_init, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * hpt3x3_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Set our PIO requirements. This is fairly simple on the HPT3x3 as + * all we have to do is clear the MWDMA and UDMA bits then load the + * mode number. + */ + +static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 r1, r2; + int dn = 2 * ap->port_no + adev->devno; + + pci_read_config_dword(pdev, 0x44, &r1); + pci_read_config_dword(pdev, 0x48, &r2); + /* Load the PIO timing number */ + r1 &= ~(7 << (3 * dn)); + r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn); + r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ + + pci_write_config_dword(pdev, 0x44, r1); + pci_write_config_dword(pdev, 0x48, r2); +} + +/** + * hpt3x3_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 r1, r2; + int dn = 2 * ap->port_no + adev->devno; + int mode_num = adev->dma_mode & 0x0F; + + pci_read_config_dword(pdev, 0x44, &r1); + pci_read_config_dword(pdev, 0x48, &r2); + /* Load the timing number */ + r1 &= ~(7 << (3 * dn)); + r1 |= (mode_num << (3 * dn)); + r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ + + if (adev->dma_mode >= XFER_UDMA_0) + r2 |= 0x01 << dn; /* Ultra mode */ + else + r2 |= 0x10 << dn; /* MWDMA */ + + pci_write_config_dword(pdev, 0x44, r1); + pci_write_config_dword(pdev, 0x48, r2); +} + +static struct scsi_host_template hpt3x3_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations hpt3x3_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt3x3_set_piomode, + .set_dmamode = hpt3x3_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt3x3_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * hpt3x3_init_one - Initialise an HPT343/363 + * @dev: PCI device + * @id: Entry in match table + * + * Perform basic initialisation. The chip has a quirk that it won't + * function unless it is at XX00. The old ATA driver touched this up + * but we leave it for pci quirks to do properly. + */ + +static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &hpt3x3_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, + .port_ops = &hpt3x3_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + u16 cmd; + + /* Initialize the board */ + pci_write_config_word(dev, 0x80, 0x00); + /* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */ + pci_read_config_word(dev, PCI_COMMAND, &cmd); + if (cmd & PCI_COMMAND_MEMORY) + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0); + else + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); + + /* Now kick off ATA set up */ + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id hpt3x3[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT343), }, + { 0, }, +}; + +static struct pci_driver hpt3x3_pci_driver = { + .name = DRV_NAME, + .id_table = hpt3x3, + .probe = hpt3x3_init_one, + .remove = ata_pci_remove_one +}; + +static int __init hpt3x3_init(void) +{ + return pci_register_driver(&hpt3x3_pci_driver); +} + + +static void __exit hpt3x3_exit(void) +{ + pci_unregister_driver(&hpt3x3_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, hpt3x3); +MODULE_VERSION(DRV_VERSION); + +module_init(hpt3x3_init); +module_exit(hpt3x3_exit); diff --git a/drivers/ata/pata_isapnp.c b/drivers/ata/pata_isapnp.c new file mode 100644 index 00000000000..640b8b0954f --- /dev/null +++ b/drivers/ata/pata_isapnp.c @@ -0,0 +1,156 @@ + +/* + * pata-isapnp.c - ISA PnP PATA controller driver. + * Copyright 2005/2006 Red Hat Inc <alan@redhat.com>, all rights reserved. + * + * Based in part on ide-pnp.c by Andrey Panin <pazke@donpac.ru> + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/isapnp.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/ata.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_isapnp" +#define DRV_VERSION "0.1.5" + +static struct scsi_host_template isapnp_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations isapnp_port_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * isapnp_init_one - attach an isapnp interface + * @idev: PnP device + * @dev_id: matching detect line + * + * Register an ISA bus IDE interface. Such interfaces are PIO 0 and + * non shared IRQ. + */ + +static int isapnp_init_one(struct pnp_dev *idev, const struct pnp_device_id *dev_id) +{ + struct ata_probe_ent ae; + + if (pnp_port_valid(idev, 0) == 0) + return -ENODEV; + + /* FIXME: Should selected polled PIO here not fail */ + if (pnp_irq_valid(idev, 0) == 0) + return -ENODEV; + + memset(&ae, 0, sizeof(struct ata_probe_ent)); + INIT_LIST_HEAD(&ae.node); + ae.dev = &idev->dev; + ae.port_ops = &isapnp_port_ops; + ae.sht = &isapnp_sht; + ae.n_ports = 1; + ae.pio_mask = 1; /* ISA so PIO 0 cycles */ + ae.irq = pnp_irq(idev, 0); + ae.irq_flags = 0; + ae.port_flags = ATA_FLAG_SLAVE_POSS; + ae.port[0].cmd_addr = pnp_port_start(idev, 0); + + if (pnp_port_valid(idev, 1) == 0) { + ae.port[0].altstatus_addr = pnp_port_start(idev, 1); + ae.port[0].ctl_addr = pnp_port_start(idev, 1); + ae.port_flags |= ATA_FLAG_SRST; + } + ata_std_ports(&ae.port[0]); + + if (ata_device_add(&ae) == 0) + return -ENODEV; + return 0; +} + +/** + * isapnp_remove_one - unplug an isapnp interface + * @idev: PnP device + * + * Remove a previously configured PnP ATA port. Called only on module + * unload events as the core does not currently deal with ISAPnP docking. + */ + +static void isapnp_remove_one(struct pnp_dev *idev) +{ + struct device *dev = &idev->dev; + struct ata_host *host = dev_get_drvdata(dev); + + ata_host_remove(host); + dev_set_drvdata(dev, NULL); +} + +static struct pnp_device_id isapnp_devices[] = { + /* Generic ESDI/IDE/ATA compatible hard disk controller */ + {.id = "PNP0600", .driver_data = 0}, + {.id = ""} +}; + +static struct pnp_driver isapnp_driver = { + .name = DRV_NAME, + .id_table = isapnp_devices, + .probe = isapnp_init_one, + .remove = isapnp_remove_one, +}; + +static int __init isapnp_init(void) +{ + return pnp_register_driver(&isapnp_driver); +} + +static void __exit isapnp_exit(void) +{ + pnp_unregister_driver(&isapnp_driver); +} + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for ISA PnP ATA"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); + +module_init(isapnp_init); +module_exit(isapnp_exit); diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c new file mode 100644 index 00000000000..82a46ff4000 --- /dev/null +++ b/drivers/ata/pata_it821x.c @@ -0,0 +1,847 @@ +/* + * ata-it821x.c - IT821x PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based upon + * + * it821x.c + * + * linux/drivers/ide/pci/it821x.c Version 0.09 December 2004 + * + * Copyright (C) 2004 Red Hat <alan@redhat.com> + * + * May be copied or modified under the terms of the GNU General Public License + * Based in part on the ITE vendor provided SCSI driver. + * + * Documentation available from + * http://www.ite.com.tw/pc/IT8212F_V04.pdf + * Some other documents are NDA. + * + * The ITE8212 isn't exactly a standard IDE controller. It has two + * modes. In pass through mode then it is an IDE controller. In its smart + * mode its actually quite a capable hardware raid controller disguised + * as an IDE controller. Smart mode only understands DMA read/write and + * identify, none of the fancier commands apply. The IT8211 is identical + * in other respects but lacks the raid mode. + * + * Errata: + * o Rev 0x10 also requires master/slave hold the same DMA timings and + * cannot do ATAPI MWDMA. + * o The identify data for raid volumes lacks CHS info (technically ok) + * but also fails to set the LBA28 and other bits. We fix these in + * the IDE probe quirk code. + * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode + * raid then the controller firmware dies + * o Smart mode without RAID doesn't clear all the necessary identify + * bits to reduce the command set to the one used + * + * This has a few impacts on the driver + * - In pass through mode we do all the work you would expect + * - In smart mode the clocking set up is done by the controller generally + * but we must watch the other limits and filter. + * - There are a few extra vendor commands that actually talk to the + * controller but only work PIO with no IRQ. + * + * Vendor areas of the identify block in smart mode are used for the + * timing and policy set up. Each HDD in raid mode also has a serial + * block on the disk. The hardware extra commands are get/set chip status, + * rebuild, get rebuild status. + * + * In Linux the driver supports pass through mode as if the device was + * just another IDE controller. If the smart mode is running then + * volumes are managed by the controller firmware and each IDE "disk" + * is a raid volume. Even more cute - the controller can do automated + * hotplug and rebuild. + * + * The pass through controller itself is a little demented. It has a + * flaw that it has a single set of PIO/MWDMA timings per channel so + * non UDMA devices restrict each others performance. It also has a + * single clock source per channel so mixed UDMA100/133 performance + * isn't perfect and we have to pick a clock. Thankfully none of this + * matters in smart mode. ATAPI DMA is not currently supported. + * + * It seems the smart mode is a win for RAID1/RAID10 but otherwise not. + * + * TODO + * - ATAPI and other speed filtering + * - Command filter in smart mode + * - RAID configuration ioctls + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + + +#define DRV_NAME "pata_it821x" +#define DRV_VERSION "0.3.2" + +struct it821x_dev +{ + unsigned int smart:1, /* Are we in smart raid mode */ + timing10:1; /* Rev 0x10 */ + u8 clock_mode; /* 0, ATA_50 or ATA_66 */ + u8 want[2][2]; /* Mode/Pri log for master slave */ + /* We need these for switching the clock when DMA goes on/off + The high byte is the 66Mhz timing */ + u16 pio[2]; /* Cached PIO values */ + u16 mwdma[2]; /* Cached MWDMA values */ + u16 udma[2]; /* Cached UDMA values (per drive) */ + u16 last_device; /* Master or slave loaded ? */ +}; + +#define ATA_66 0 +#define ATA_50 1 +#define ATA_ANY 2 + +#define UDMA_OFF 0 +#define MWDMA_OFF 0 + +/* + * We allow users to force the card into non raid mode without + * flashing the alternative BIOS. This is also neccessary right now + * for embedded platforms that cannot run a PC BIOS but are using this + * device. + */ + +static int it8212_noraid; + +/** + * it821x_pre_reset - probe + * @ap: ATA port + * + * Set the cable type + */ + +static int it821x_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +/** + * it821x_error_handler - probe/reset + * @ap: ATA port + * + * Set the cable type and trigger a probe + */ + +static void it821x_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, it821x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * it821x_program - program the PIO/MWDMA registers + * @ap: ATA port + * @adev: Device to program + * @timing: Timing value (66Mhz in top 8bits, 50 in the low 8) + * + * Program the PIO/MWDMA timing for this channel according to the + * current clock. These share the same register so are managed by + * the DMA start/stop sequence as with the old driver. + */ + +static void it821x_program(struct ata_port *ap, struct ata_device *adev, u16 timing) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct it821x_dev *itdev = ap->private_data; + int channel = ap->port_no; + u8 conf; + + /* Program PIO/MWDMA timing bits */ + if (itdev->clock_mode == ATA_66) + conf = timing >> 8; + else + conf = timing & 0xFF; + pci_write_config_byte(pdev, 0x54 + 4 * channel, conf); +} + + +/** + * it821x_program_udma - program the UDMA registers + * @ap: ATA port + * @adev: ATA device to update + * @timing: Timing bits. Top 8 are for 66Mhz bottom for 50Mhz + * + * Program the UDMA timing for this drive according to the + * current clock. Handles the dual clocks and also knows about + * the errata on the 0x10 revision. The UDMA errata is partly handled + * here and partly in start_dma. + */ + +static void it821x_program_udma(struct ata_port *ap, struct ata_device *adev, u16 timing) +{ + struct it821x_dev *itdev = ap->private_data; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int channel = ap->port_no; + int unit = adev->devno; + u8 conf; + + /* Program UDMA timing bits */ + if (itdev->clock_mode == ATA_66) + conf = timing >> 8; + else + conf = timing & 0xFF; + if (itdev->timing10 == 0) + pci_write_config_byte(pdev, 0x56 + 4 * channel + unit, conf); + else { + /* Early revision must be programmed for both together */ + pci_write_config_byte(pdev, 0x56 + 4 * channel, conf); + pci_write_config_byte(pdev, 0x56 + 4 * channel + 1, conf); + } +} + +/** + * it821x_clock_strategy + * @ap: ATA interface + * @adev: ATA device being updated + * + * Select between the 50 and 66Mhz base clocks to get the best + * results for this interface. + */ + +static void it821x_clock_strategy(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct it821x_dev *itdev = ap->private_data; + u8 unit = adev->devno; + struct ata_device *pair = ata_dev_pair(adev); + + int clock, altclock; + u8 v; + int sel = 0; + + /* Look for the most wanted clocking */ + if (itdev->want[0][0] > itdev->want[1][0]) { + clock = itdev->want[0][1]; + altclock = itdev->want[1][1]; + } else { + clock = itdev->want[1][1]; + altclock = itdev->want[0][1]; + } + + /* Master doesn't care does the slave ? */ + if (clock == ATA_ANY) + clock = altclock; + + /* Nobody cares - keep the same clock */ + if (clock == ATA_ANY) + return; + /* No change */ + if (clock == itdev->clock_mode) + return; + + /* Load this into the controller */ + if (clock == ATA_66) + itdev->clock_mode = ATA_66; + else { + itdev->clock_mode = ATA_50; + sel = 1; + } + pci_read_config_byte(pdev, 0x50, &v); + v &= ~(1 << (1 + ap->port_no)); + v |= sel << (1 + ap->port_no); + pci_write_config_byte(pdev, 0x50, v); + + /* + * Reprogram the UDMA/PIO of the pair drive for the switch + * MWDMA will be dealt with by the dma switcher + */ + if (pair && itdev->udma[1-unit] != UDMA_OFF) { + it821x_program_udma(ap, pair, itdev->udma[1-unit]); + it821x_program(ap, pair, itdev->pio[1-unit]); + } + /* + * Reprogram the UDMA/PIO of our drive for the switch. + * MWDMA will be dealt with by the dma switcher + */ + if (itdev->udma[unit] != UDMA_OFF) { + it821x_program_udma(ap, adev, itdev->udma[unit]); + it821x_program(ap, adev, itdev->pio[unit]); + } +} + +/** + * it821x_passthru_set_piomode - set PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Configure for PIO mode. This is complicated as the register is + * shared by PIO and MWDMA and for both channels. + */ + +static void it821x_passthru_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + /* Spec says 89 ref driver uses 88 */ + static const u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 }; + static const u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY }; + + struct it821x_dev *itdev = ap->private_data; + int unit = adev->devno; + int mode_wanted = adev->pio_mode - XFER_PIO_0; + + /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */ + itdev->want[unit][1] = pio_want[mode_wanted]; + itdev->want[unit][0] = 1; /* PIO is lowest priority */ + itdev->pio[unit] = pio[mode_wanted]; + it821x_clock_strategy(ap, adev); + it821x_program(ap, adev, itdev->pio[unit]); +} + +/** + * it821x_passthru_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Set up the DMA modes. The actions taken depend heavily on the mode + * to use. If UDMA is used as is hopefully the usual case then the + * timing register is private and we need only consider the clock. If + * we are using MWDMA then we have to manage the setting ourself as + * we switch devices and mode. + */ + +static void it821x_passthru_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const u16 dma[] = { 0x8866, 0x3222, 0x3121 }; + static const u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY }; + static const u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 }; + static const u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct it821x_dev *itdev = ap->private_data; + int channel = ap->port_no; + int unit = adev->devno; + u8 conf; + + if (adev->dma_mode >= XFER_UDMA_0) { + int mode_wanted = adev->dma_mode - XFER_UDMA_0; + + itdev->want[unit][1] = udma_want[mode_wanted]; + itdev->want[unit][0] = 3; /* UDMA is high priority */ + itdev->mwdma[unit] = MWDMA_OFF; + itdev->udma[unit] = udma[mode_wanted]; + if (mode_wanted >= 5) + itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */ + + /* UDMA on. Again revision 0x10 must do the pair */ + pci_read_config_byte(pdev, 0x50, &conf); + if (itdev->timing10) + conf &= channel ? 0x9F: 0xE7; + else + conf &= ~ (1 << (3 + 2 * channel + unit)); + pci_write_config_byte(pdev, 0x50, conf); + it821x_clock_strategy(ap, adev); + it821x_program_udma(ap, adev, itdev->udma[unit]); + } else { + int mode_wanted = adev->dma_mode - XFER_MW_DMA_0; + + itdev->want[unit][1] = mwdma_want[mode_wanted]; + itdev->want[unit][0] = 2; /* MWDMA is low priority */ + itdev->mwdma[unit] = dma[mode_wanted]; + itdev->udma[unit] = UDMA_OFF; + + /* UDMA bits off - Revision 0x10 do them in pairs */ + pci_read_config_byte(pdev, 0x50, &conf); + if (itdev->timing10) + conf |= channel ? 0x60: 0x18; + else + conf |= 1 << (3 + 2 * channel + unit); + pci_write_config_byte(pdev, 0x50, conf); + it821x_clock_strategy(ap, adev); + } +} + +/** + * it821x_passthru_dma_start - DMA start callback + * @qc: Command in progress + * + * Usually drivers set the DMA timing at the point the set_dmamode call + * is made. IT821x however requires we load new timings on the + * transitions in some cases. + */ + +static void it821x_passthru_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct it821x_dev *itdev = ap->private_data; + int unit = adev->devno; + + if (itdev->mwdma[unit] != MWDMA_OFF) + it821x_program(ap, adev, itdev->mwdma[unit]); + else if (itdev->udma[unit] != UDMA_OFF && itdev->timing10) + it821x_program_udma(ap, adev, itdev->udma[unit]); + ata_bmdma_start(qc); +} + +/** + * it821x_passthru_dma_stop - DMA stop callback + * @qc: ATA command + * + * We loaded new timings in dma_start, as a result we need to restore + * the PIO timings in dma_stop so that the next command issue gets the + * right clock values. + */ + +static void it821x_passthru_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct it821x_dev *itdev = ap->private_data; + int unit = adev->devno; + + ata_bmdma_stop(qc); + if (itdev->mwdma[unit] != MWDMA_OFF) + it821x_program(ap, adev, itdev->pio[unit]); +} + + +/** + * it821x_passthru_dev_select - Select master/slave + * @ap: ATA port + * @device: Device number (not pointer) + * + * Device selection hook. If neccessary perform clock switching + */ + +static void it821x_passthru_dev_select(struct ata_port *ap, + unsigned int device) +{ + struct it821x_dev *itdev = ap->private_data; + if (itdev && device != itdev->last_device) { + struct ata_device *adev = &ap->device[device]; + it821x_program(ap, adev, itdev->pio[adev->devno]); + itdev->last_device = device; + } + ata_std_dev_select(ap, device); +} + +/** + * it821x_smart_qc_issue_prot - wrap qc issue prot + * @qc: command + * + * Wrap the command issue sequence for the IT821x. We need to + * perform out own device selection timing loads before the + * usual happenings kick off + */ + +static unsigned int it821x_smart_qc_issue_prot(struct ata_queued_cmd *qc) +{ + switch(qc->tf.command) + { + /* Commands the firmware supports */ + case ATA_CMD_READ: + case ATA_CMD_READ_EXT: + case ATA_CMD_WRITE: + case ATA_CMD_WRITE_EXT: + case ATA_CMD_PIO_READ: + case ATA_CMD_PIO_READ_EXT: + case ATA_CMD_PIO_WRITE: + case ATA_CMD_PIO_WRITE_EXT: + case ATA_CMD_READ_MULTI: + case ATA_CMD_READ_MULTI_EXT: + case ATA_CMD_WRITE_MULTI: + case ATA_CMD_WRITE_MULTI_EXT: + case ATA_CMD_ID_ATA: + /* Arguably should just no-op this one */ + case ATA_CMD_SET_FEATURES: + return ata_qc_issue_prot(qc); + } + printk(KERN_DEBUG "it821x: can't process command 0x%02X\n", qc->tf.command); + return AC_ERR_INVALID; +} + +/** + * it821x_passthru_qc_issue_prot - wrap qc issue prot + * @qc: command + * + * Wrap the command issue sequence for the IT821x. We need to + * perform out own device selection timing loads before the + * usual happenings kick off + */ + +static unsigned int it821x_passthru_qc_issue_prot(struct ata_queued_cmd *qc) +{ + it821x_passthru_dev_select(qc->ap, qc->dev->devno); + return ata_qc_issue_prot(qc); +} + +/** + * it821x_smart_set_mode - mode setting + * @ap: interface to set up + * + * Use a non standard set_mode function. We don't want to be tuned. + * The BIOS configured everything. Our job is not to fiddle. We + * read the dma enabled bits from the PCI configuration of the device + * and respect them. + */ + +static void it821x_smart_set_mode(struct ata_port *ap) +{ + int dma_enabled = 0; + int i; + + /* Bits 5 and 6 indicate if DMA is active on master/slave */ + /* It is possible that BMDMA isn't allocated */ + if (ap->ioaddr.bmdma_addr) + dma_enabled = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + if (ata_dev_enabled(dev)) { + /* We don't really care */ + dev->pio_mode = XFER_PIO_0; + dev->dma_mode = XFER_MW_DMA_0; + /* We do need the right mode information for DMA or PIO + and this comes from the current configuration flags */ + if (dma_enabled & (1 << (5 + i))) { + dev->xfer_mode = XFER_MW_DMA_0; + dev->xfer_shift = ATA_SHIFT_MWDMA; + dev->flags &= ~ATA_DFLAG_PIO; + } else { + dev->xfer_mode = XFER_PIO_0; + dev->xfer_shift = ATA_SHIFT_PIO; + dev->flags |= ATA_DFLAG_PIO; + } + } + } +} + +/** + * it821x_dev_config - Called each device identify + * @ap: ATA port + * @adev: Device that has just been identified + * + * Perform the initial setup needed for each device that is chip + * special. In our case we need to lock the sector count to avoid + * blowing the brains out of the firmware with large LBA48 requests + * + * FIXME: When FUA appears we need to block FUA too. And SMART and + * basically we need to filter commands for this chip. + */ + +static void it821x_dev_config(struct ata_port *ap, struct ata_device *adev) +{ + unsigned char model_num[40]; + char *s; + unsigned int len; + + /* This block ought to be a library routine as it is in several + drivers now */ + + ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, + sizeof(model_num)); + s = &model_num[0]; + len = strnlen(s, sizeof(model_num)); + + /* ATAPI specifies that empty space is blank-filled; remove blanks */ + while ((len > 0) && (s[len - 1] == ' ')) { + len--; + s[len] = 0; + } + + if (adev->max_sectors > 255) + adev->max_sectors = 255; + + if (strstr(model_num, "Integrated Technology Express")) { + /* RAID mode */ + printk(KERN_INFO "IT821x %sRAID%d volume", + adev->id[147]?"Bootable ":"", + adev->id[129]); + if (adev->id[129] != 1) + printk("(%dK stripe)", adev->id[146]); + printk(".\n"); + } +} + + +/** + * it821x_check_atapi_dma - ATAPI DMA handler + * @qc: Command we are about to issue + * + * Decide if this ATAPI command can be issued by DMA on this + * controller. Return 0 if it can be. + */ + +static int it821x_check_atapi_dma(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct it821x_dev *itdev = ap->private_data; + + /* No ATAPI DMA in smart mode */ + if (itdev->smart) + return -EOPNOTSUPP; + /* No ATAPI DMA on rev 10 */ + if (itdev->timing10) + return -EOPNOTSUPP; + /* Cool */ + return 0; +} + + +/** + * it821x_port_start - port setup + * @ap: ATA port being set up + * + * The it821x needs to maintain private data structures and also to + * use the standard PCI interface which lacks support for this + * functionality. We instead set up the private data on the port + * start hook, and tear it down on port stop + */ + +static int it821x_port_start(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct it821x_dev *itdev; + u8 conf; + + int ret = ata_port_start(ap); + if (ret < 0) + return ret; + + ap->private_data = kmalloc(sizeof(struct it821x_dev), GFP_KERNEL); + if (ap->private_data == NULL) { + ata_port_stop(ap); + return -ENOMEM; + } + + itdev = ap->private_data; + memset(itdev, 0, sizeof(struct it821x_dev)); + + pci_read_config_byte(pdev, 0x50, &conf); + + if (conf & 1) { + itdev->smart = 1; + /* Long I/O's although allowed in LBA48 space cause the + onboard firmware to enter the twighlight zone */ + /* No ATAPI DMA in this mode either */ + } + /* Pull the current clocks from 0x50 */ + if (conf & (1 << (1 + ap->port_no))) + itdev->clock_mode = ATA_50; + else + itdev->clock_mode = ATA_66; + + itdev->want[0][1] = ATA_ANY; + itdev->want[1][1] = ATA_ANY; + itdev->last_device = -1; + + pci_read_config_byte(pdev, PCI_REVISION_ID, &conf); + if (conf == 0x10) { + itdev->timing10 = 1; + /* Need to disable ATAPI DMA for this case */ + if (!itdev->smart) + printk(KERN_WARNING DRV_NAME": Revision 0x10, workarounds activated.\n"); + } + + return 0; +} + +/** + * it821x_port_stop - port shutdown + * @ap: ATA port being removed + * + * Release the private objects we added in it821x_port_start + */ + +static void it821x_port_stop(struct ata_port *ap) { + kfree(ap->private_data); + ap->private_data = NULL; /* We want an OOPS if we reuse this + too late! */ + ata_port_stop(ap); +} + +static struct scsi_host_template it821x_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + /* 255 sectors to begin with. This is locked in smart mode but not + in pass through */ + .max_sectors = 255, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations it821x_smart_port_ops = { + .set_mode = it821x_smart_set_mode, + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .mode_filter = ata_pci_default_filter, + + .check_status = ata_check_status, + .check_atapi_dma= it821x_check_atapi_dma, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .dev_config = it821x_dev_config, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = it821x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = it821x_smart_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = it821x_port_start, + .port_stop = it821x_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations it821x_passthru_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = it821x_passthru_set_piomode, + .set_dmamode = it821x_passthru_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .check_atapi_dma= it821x_check_atapi_dma, + .dev_select = it821x_passthru_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = it821x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = it821x_passthru_bmdma_start, + .bmdma_stop = it821x_passthru_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = it821x_passthru_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_clear = ata_bmdma_irq_clear, + .irq_handler = ata_interrupt, + + .port_start = it821x_port_start, + .port_stop = it821x_port_stop, + .host_stop = ata_host_stop +}; + +static void __devinit it821x_disable_raid(struct pci_dev *pdev) +{ + /* Reset local CPU, and set BIOS not ready */ + pci_write_config_byte(pdev, 0x5E, 0x01); + + /* Set to bypass mode, and reset PCI bus */ + pci_write_config_byte(pdev, 0x50, 0x00); + pci_write_config_word(pdev, PCI_COMMAND, + PCI_COMMAND_PARITY | PCI_COMMAND_IO | + PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + pci_write_config_word(pdev, 0x40, 0xA0F3); + + pci_write_config_dword(pdev,0x4C, 0x02040204); + pci_write_config_byte(pdev, 0x42, 0x36); + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x20); +} + + +static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + u8 conf; + + static struct ata_port_info info_smart = { + .sht = &it821x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &it821x_smart_port_ops + }; + static struct ata_port_info info_passthru = { + .sht = &it821x_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &it821x_passthru_port_ops + }; + static struct ata_port_info *port_info[2]; + + static char *mode[2] = { "pass through", "smart" }; + + /* Force the card into bypass mode if so requested */ + if (it8212_noraid) { + printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n"); + it821x_disable_raid(pdev); + } + pci_read_config_byte(pdev, 0x50, &conf); + conf &= 1; + + printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]); + if (conf == 0) + port_info[0] = port_info[1] = &info_passthru; + else + port_info[0] = port_info[1] = &info_smart; + + return ata_pci_init_one(pdev, port_info, 2); +} + +static struct pci_device_id it821x[] = { + { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211), }, + { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212), }, + { 0, }, +}; + +static struct pci_driver it821x_pci_driver = { + .name = DRV_NAME, + .id_table = it821x, + .probe = it821x_init_one, + .remove = ata_pci_remove_one +}; + +static int __init it821x_init(void) +{ + return pci_register_driver(&it821x_pci_driver); +} + + +static void __exit it821x_exit(void) +{ + pci_unregister_driver(&it821x_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the IT8211/IT8212 IDE RAID controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, it821x); +MODULE_VERSION(DRV_VERSION); + + +module_param_named(noraid, it8212_noraid, int, S_IRUGO); +MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode"); + +module_init(it821x_init); +module_exit(it821x_exit); diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c new file mode 100644 index 00000000000..be3a866b111 --- /dev/null +++ b/drivers/ata/pata_jmicron.c @@ -0,0 +1,265 @@ +/* + * pata_jmicron.c - JMicron ATA driver for non AHCI mode. This drives the + * PATA port of the controller. The SATA ports are + * driven by AHCI in the usual configuration although + * this driver can handle other setups if we need it. + * + * (c) 2006 Red Hat <alan@redhat.com> + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_jmicron" +#define DRV_VERSION "0.1.2" + +typedef enum { + PORT_PATA0 = 0, + PORT_PATA1 = 1, + PORT_SATA = 2, +} port_type; + +/** + * jmicron_pre_reset - check for 40/80 pin + * @ap: Port + * + * Perform the PATA port setup we need. + + * On the Jmicron 361/363 there is a single PATA port that can be mapped + * either as primary or secondary (or neither). We don't do any policy + * and setup here. We assume that has been done by init_one and the + * BIOS. + */ + +static int jmicron_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 control; + u32 control5; + int port_mask = 1<< (4 * ap->port_no); + int port = ap->port_no; + port_type port_map[2]; + + /* Check if our port is enabled */ + pci_read_config_dword(pdev, 0x40, &control); + if ((control & port_mask) == 0) + return -ENOENT; + + /* There are two basic mappings. One has the two SATA ports merged + as master/slave and the secondary as PATA, the other has only the + SATA port mapped */ + if (control & (1 << 23)) { + port_map[0] = PORT_SATA; + port_map[1] = PORT_PATA0; + } else { + port_map[0] = PORT_SATA; + port_map[1] = PORT_SATA; + } + + /* The 365/366 may have this bit set to map the second PATA port + as the internal primary channel */ + pci_read_config_dword(pdev, 0x80, &control5); + if (control5 & (1<<24)) + port_map[0] = PORT_PATA1; + + /* The two ports may then be logically swapped by the firmware */ + if (control & (1 << 22)) + port = port ^ 1; + + /* + * Now we know which physical port we are talking about we can + * actually do our cable checking etc. Thankfully we don't need + * to do the plumbing for other cases. + */ + switch (port_map[port]) + { + case PORT_PATA0: + if (control & (1 << 5)) + return 0; + if (control & (1 << 3)) /* 40/80 pin primary */ + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + break; + case PORT_PATA1: + /* Bit 21 is set if the port is enabled */ + if ((control5 & (1 << 21)) == 0) + return 0; + if (control5 & (1 << 19)) /* 40/80 pin secondary */ + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + break; + case PORT_SATA: + ap->cbl = ATA_CBL_SATA; + break; + } + return ata_std_prereset(ap); +} + +/** + * jmicron_error_handler - Setup and error handler + * @ap: Port to handle + * + * LOCKING: + * None (inherited from caller). + */ + +static void jmicron_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, jmicron_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/* No PIO or DMA methods needed for this device */ + +static struct scsi_host_template jmicron_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + /* Special handling needed if you have sector or LBA48 limits */ + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + /* Use standard CHS mapping rules */ + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations jmicron_ops = { + .port_disable = ata_port_disable, + + /* Task file is PCI ATA format, use helpers */ + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = jmicron_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + /* BMDMA handling is PCI ATA format, use helpers */ + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + /* IRQ-related hooks */ + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + /* Generic PATA PCI ATA helpers */ + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + + +/** + * jmicron_init_one - Register Jmicron ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in jmicron_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &jmicron_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + + .port_ops = &jmicron_ops, + }; + struct ata_port_info *port_info[2] = { &info, &info }; + + u32 reg; + + if (id->driver_data != 368) { + /* Put the controller into AHCI mode in case the AHCI driver + has not yet been loaded. This can be done with either + function present */ + + /* FIXME: We may want a way to override this in future */ + pci_write_config_byte(pdev, 0x41, 0xa1); + } + + /* PATA controller is fn 1, AHCI is fn 0 */ + if (PCI_FUNC(pdev->devfn) != 1) + return -ENODEV; + + if ( id->driver_data == 365 || id->driver_data == 366) { + /* The 365/66 have two PATA channels, redirect the second */ + pci_read_config_dword(pdev, 0x80, ®); + reg |= (1 << 24); /* IDE1 to PATA IDE secondary */ + pci_write_config_dword(pdev, 0x80, reg); + } + + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id jmicron_pci_tbl[] = { + { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361), 361}, + { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363), 363}, + { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365), 365}, + { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366), 366}, + { PCI_DEVICE(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368), 368}, + { } /* terminate list */ +}; + +static struct pci_driver jmicron_pci_driver = { + .name = DRV_NAME, + .id_table = jmicron_pci_tbl, + .probe = jmicron_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init jmicron_init(void) +{ + return pci_register_driver(&jmicron_pci_driver); +} + +static void __exit jmicron_exit(void) +{ + pci_unregister_driver(&jmicron_pci_driver); +} + +module_init(jmicron_init); +module_exit(jmicron_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for Jmicron PATA ports"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, jmicron_pci_tbl); +MODULE_VERSION(DRV_VERSION); + diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c new file mode 100644 index 00000000000..10231ef731d --- /dev/null +++ b/drivers/ata/pata_legacy.c @@ -0,0 +1,949 @@ +/* + * pata-legacy.c - Legacy port PATA/SATA controller driver. + * Copyright 2005/2006 Red Hat <alan@redhat.com>, all rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * An ATA driver for the legacy ATA ports. + * + * Data Sources: + * Opti 82C465/82C611 support: Data sheets at opti-inc.com + * HT6560 series: + * Promise 20230/20620: + * http://www.ryston.cz/petr/vlb/pdc20230b.html + * http://www.ryston.cz/petr/vlb/pdc20230c.html + * http://www.ryston.cz/petr/vlb/pdc20630.html + * + * Unsupported but docs exist: + * Appian/Adaptec AIC25VL01/Cirrus Logic PD7220 + * Winbond W83759A + * + * This driver handles legacy (that is "ISA/VLB side") IDE ports found + * on PC class systems. There are three hybrid devices that are exceptions + * The Cyrix 5510/5520 where a pre SFF ATA device is on the bridge and + * the MPIIX where the tuning is PCI side but the IDE is "ISA side". + * + * Specific support is included for the ht6560a/ht6560b/opti82c611a/ + * opti82c465mv/promise 20230c/20630 + * + * Use the autospeed and pio_mask options with: + * Appian ADI/2 aka CLPD7220 or AIC25VL01. + * Use the jumpers, autospeed and set pio_mask to the mode on the jumpers with + * Goldstar GM82C711, PIC-1288A-125, UMC 82C871F, Winbond W83759, + * Winbond W83759A, Promise PDC20230-B + * + * For now use autospeed and pio_mask as above with the W83759A. This may + * change. + * + * TODO + * Merge existing pata_qdi driver + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/ata.h> +#include <linux/libata.h> +#include <linux/platform_device.h> + +#define DRV_NAME "pata_legacy" +#define DRV_VERSION "0.5.3" + +#define NR_HOST 6 + +static int legacy_port[NR_HOST] = { 0x1f0, 0x170, 0x1e8, 0x168, 0x1e0, 0x160 }; +static int legacy_irq[NR_HOST] = { 15, 14, 11, 10, 8, 12 }; + +struct legacy_data { + unsigned long timing; + u8 clock[2]; + u8 last; + int fast; + struct platform_device *platform_dev; + +}; + +static struct legacy_data legacy_data[NR_HOST]; +static struct ata_host *legacy_host[NR_HOST]; +static int nr_legacy_host; + + +static int probe_all; /* Set to check all ISA port ranges */ +static int ht6560a; /* HT 6560A on primary 1, secondary 2, both 3 */ +static int ht6560b; /* HT 6560A on primary 1, secondary 2, both 3 */ +static int opti82c611a; /* Opti82c611A on primary 1, secondary 2, both 3 */ +static int opti82c46x; /* Opti 82c465MV present (pri/sec autodetect) */ +static int autospeed; /* Chip present which snoops speed changes */ +static int pio_mask = 0x1F; /* PIO range for autospeed devices */ + +/** + * legacy_set_mode - mode setting + * @ap: IDE interface + * + * Use a non standard set_mode function. We don't want to be tuned. + * + * The BIOS configured everything. Our job is not to fiddle. Just use + * whatever PIO the hardware is using and leave it at that. When we + * get some kind of nice user driven API for control then we can + * expand on this as per hdparm in the base kernel. + */ + +static void legacy_set_mode(struct ata_port *ap) +{ + int i; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + if (ata_dev_enabled(dev)) { + dev->pio_mode = XFER_PIO_0; + dev->xfer_mode = XFER_PIO_0; + dev->xfer_shift = ATA_SHIFT_PIO; + dev->flags |= ATA_DFLAG_PIO; + } + } +} + +static struct scsi_host_template legacy_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +/* + * These ops are used if the user indicates the hardware + * snoops the commands to decide on the mode and handles the + * mode selection "magically" itself. Several legacy controllers + * do this. The mode range can be set if it is not 0x1F by setting + * pio_mask as well. + */ + +static struct ata_port_operations simple_port_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer_noirq, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations legacy_port_ops = { + .set_mode = legacy_set_mode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = ata_bmdma_error_handler, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer_noirq, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Promise 20230C and 20620 support + * + * This controller supports PIO0 to PIO2. We set PIO timings conservatively to + * allow for 50MHz Vesa Local Bus. The 20620 DMA support is weird being DMA to + * controller and PIO'd to the host and not supported. + */ + +static void pdc20230_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + int tries = 5; + int pio = adev->pio_mode - XFER_PIO_0; + u8 rt; + unsigned long flags; + + /* Safe as UP only. Force I/Os to occur together */ + + local_irq_save(flags); + + /* Unlock the control interface */ + do + { + inb(0x1F5); + outb(inb(0x1F2) | 0x80, 0x1F2); + inb(0x1F2); + inb(0x3F6); + inb(0x3F6); + inb(0x1F2); + inb(0x1F2); + } + while((inb(0x1F2) & 0x80) && --tries); + + local_irq_restore(flags); + + outb(inb(0x1F4) & 0x07, 0x1F4); + + rt = inb(0x1F3); + rt &= 0x07 << (3 * adev->devno); + if (pio) + rt |= (1 + 3 * pio) << (3 * adev->devno); + + udelay(100); + outb(inb(0x1F2) | 0x01, 0x1F2); + udelay(100); + inb(0x1F5); + +} + +static void pdc_data_xfer_vlb(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data) +{ + struct ata_port *ap = adev->ap; + int slop = buflen & 3; + unsigned long flags; + + if (ata_id_has_dword_io(adev->id)) { + local_irq_save(flags); + + /* Perform the 32bit I/O synchronization sequence */ + inb(ap->ioaddr.nsect_addr); + inb(ap->ioaddr.nsect_addr); + inb(ap->ioaddr.nsect_addr); + + /* Now the data */ + + if (write_data) + outsl(ap->ioaddr.data_addr, buf, buflen >> 2); + else + insl(ap->ioaddr.data_addr, buf, buflen >> 2); + + if (unlikely(slop)) { + u32 pad; + if (write_data) { + memcpy(&pad, buf + buflen - slop, slop); + outl(le32_to_cpu(pad), ap->ioaddr.data_addr); + } else { + pad = cpu_to_le16(inl(ap->ioaddr.data_addr)); + memcpy(buf + buflen - slop, &pad, slop); + } + } + local_irq_restore(flags); + } + else + ata_pio_data_xfer_noirq(adev, buf, buflen, write_data); +} + +static struct ata_port_operations pdc20230_port_ops = { + .set_piomode = pdc20230_set_piomode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = ata_bmdma_error_handler, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = pdc_data_xfer_vlb, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Holtek 6560A support + * + * This controller supports PIO0 to PIO2 (no IORDY even though higher timings + * can be loaded). + */ + +static void ht6560a_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + u8 active, recover; + struct ata_timing t; + + /* Get the timing data in cycles. For now play safe at 50Mhz */ + ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000); + + active = FIT(t.active, 2, 15); + recover = FIT(t.recover, 4, 15); + + inb(0x3E6); + inb(0x3E6); + inb(0x3E6); + inb(0x3E6); + + outb(recover << 4 | active, ap->ioaddr.device_addr); + inb(ap->ioaddr.status_addr); +} + +static struct ata_port_operations ht6560a_port_ops = { + .set_piomode = ht6560a_set_piomode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = ata_bmdma_error_handler, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, /* Check vlb/noirq */ + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Holtek 6560B support + * + * This controller supports PIO0 to PIO4. We honour the BIOS/jumper FIFO setting + * unless we see an ATAPI device in which case we force it off. + * + * FIXME: need to implement 2nd channel support. + */ + +static void ht6560b_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + u8 active, recover; + struct ata_timing t; + + /* Get the timing data in cycles. For now play safe at 50Mhz */ + ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000); + + active = FIT(t.active, 2, 15); + recover = FIT(t.recover, 2, 16); + recover &= 0x15; + + inb(0x3E6); + inb(0x3E6); + inb(0x3E6); + inb(0x3E6); + + outb(recover << 4 | active, ap->ioaddr.device_addr); + + if (adev->class != ATA_DEV_ATA) { + u8 rconf = inb(0x3E6); + if (rconf & 0x24) { + rconf &= ~ 0x24; + outb(rconf, 0x3E6); + } + } + inb(ap->ioaddr.status_addr); +} + +static struct ata_port_operations ht6560b_port_ops = { + .set_piomode = ht6560b_set_piomode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = ata_bmdma_error_handler, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, /* FIXME: Check 32bit and noirq */ + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Opti core chipset helpers + */ + +/** + * opti_syscfg - read OPTI chipset configuration + * @reg: Configuration register to read + * + * Returns the value of an OPTI system board configuration register. + */ + +static u8 opti_syscfg(u8 reg) +{ + unsigned long flags; + u8 r; + + /* Uniprocessor chipset and must force cycles adjancent */ + local_irq_save(flags); + outb(reg, 0x22); + r = inb(0x24); + local_irq_restore(flags); + return r; +} + +/* + * Opti 82C611A + * + * This controller supports PIO0 to PIO3. + */ + +static void opti82c611a_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + u8 active, recover, setup; + struct ata_timing t; + struct ata_device *pair = ata_dev_pair(adev); + int clock; + int khz[4] = { 50000, 40000, 33000, 25000 }; + u8 rc; + + /* Enter configuration mode */ + inw(ap->ioaddr.error_addr); + inw(ap->ioaddr.error_addr); + outb(3, ap->ioaddr.nsect_addr); + + /* Read VLB clock strapping */ + clock = 1000000000 / khz[inb(ap->ioaddr.lbah_addr) & 0x03]; + + /* Get the timing data in cycles */ + ata_timing_compute(adev, adev->pio_mode, &t, clock, 1000); + + /* Setup timing is shared */ + if (pair) { + struct ata_timing tp; + ata_timing_compute(pair, pair->pio_mode, &tp, clock, 1000); + + ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP); + } + + active = FIT(t.active, 2, 17) - 2; + recover = FIT(t.recover, 1, 16) - 1; + setup = FIT(t.setup, 1, 4) - 1; + + /* Select the right timing bank for write timing */ + rc = inb(ap->ioaddr.lbal_addr); + rc &= 0x7F; + rc |= (adev->devno << 7); + outb(rc, ap->ioaddr.lbal_addr); + + /* Write the timings */ + outb(active << 4 | recover, ap->ioaddr.error_addr); + + /* Select the right bank for read timings, also + load the shared timings for address */ + rc = inb(ap->ioaddr.device_addr); + rc &= 0xC0; + rc |= adev->devno; /* Index select */ + rc |= (setup << 4) | 0x04; + outb(rc, ap->ioaddr.device_addr); + + /* Load the read timings */ + outb(active << 4 | recover, ap->ioaddr.data_addr); + + /* Ensure the timing register mode is right */ + rc = inb (ap->ioaddr.lbal_addr); + rc &= 0x73; + rc |= 0x84; + outb(rc, ap->ioaddr.lbal_addr); + + /* Exit command mode */ + outb(0x83, ap->ioaddr.nsect_addr); +} + + +static struct ata_port_operations opti82c611a_port_ops = { + .set_piomode = opti82c611a_set_piomode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = ata_bmdma_error_handler, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Opti 82C465MV + * + * This controller supports PIO0 to PIO3. Unlike the 611A the MVB + * version is dual channel but doesn't have a lot of unique registers. + */ + +static void opti82c46x_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + u8 active, recover, setup; + struct ata_timing t; + struct ata_device *pair = ata_dev_pair(adev); + int clock; + int khz[4] = { 50000, 40000, 33000, 25000 }; + u8 rc; + u8 sysclk; + + /* Get the clock */ + sysclk = opti_syscfg(0xAC) & 0xC0; /* BIOS set */ + + /* Enter configuration mode */ + inw(ap->ioaddr.error_addr); + inw(ap->ioaddr.error_addr); + outb(3, ap->ioaddr.nsect_addr); + + /* Read VLB clock strapping */ + clock = 1000000000 / khz[sysclk]; + + /* Get the timing data in cycles */ + ata_timing_compute(adev, adev->pio_mode, &t, clock, 1000); + + /* Setup timing is shared */ + if (pair) { + struct ata_timing tp; + ata_timing_compute(pair, pair->pio_mode, &tp, clock, 1000); + + ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP); + } + + active = FIT(t.active, 2, 17) - 2; + recover = FIT(t.recover, 1, 16) - 1; + setup = FIT(t.setup, 1, 4) - 1; + + /* Select the right timing bank for write timing */ + rc = inb(ap->ioaddr.lbal_addr); + rc &= 0x7F; + rc |= (adev->devno << 7); + outb(rc, ap->ioaddr.lbal_addr); + + /* Write the timings */ + outb(active << 4 | recover, ap->ioaddr.error_addr); + + /* Select the right bank for read timings, also + load the shared timings for address */ + rc = inb(ap->ioaddr.device_addr); + rc &= 0xC0; + rc |= adev->devno; /* Index select */ + rc |= (setup << 4) | 0x04; + outb(rc, ap->ioaddr.device_addr); + + /* Load the read timings */ + outb(active << 4 | recover, ap->ioaddr.data_addr); + + /* Ensure the timing register mode is right */ + rc = inb (ap->ioaddr.lbal_addr); + rc &= 0x73; + rc |= 0x84; + outb(rc, ap->ioaddr.lbal_addr); + + /* Exit command mode */ + outb(0x83, ap->ioaddr.nsect_addr); + + /* We need to know this for quad device on the MVB */ + ap->host->private_data = ap; +} + +/** + * opt82c465mv_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings. The + * MVB has a single set of timing registers and these are shared + * across channels. As there are two registers we really ought to + * track the last two used values as a sort of register window. For + * now we just reload on a channel switch. On the single channel + * setup this condition never fires so we do nothing extra. + * + * FIXME: dual channel needs ->serialize support + */ + +static unsigned int opti82c46x_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + /* If timings are set and for the wrong channel (2nd test is + due to a libata shortcoming and will eventually go I hope) */ + if (ap->host->private_data != ap->host + && ap->host->private_data != NULL) + opti82c46x_set_piomode(ap, adev); + + return ata_qc_issue_prot(qc); +} + +static struct ata_port_operations opti82c46x_port_ops = { + .set_piomode = opti82c46x_set_piomode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = ata_bmdma_error_handler, + + .qc_prep = ata_qc_prep, + .qc_issue = opti82c46x_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + + +/** + * legacy_init_one - attach a legacy interface + * @port: port number + * @io: I/O port start + * @ctrl: control port + * @irq: interrupt line + * + * Register an ISA bus IDE interface. Such interfaces are PIO and we + * assume do not support IRQ sharing. + */ + +static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl, int irq) +{ + struct legacy_data *ld = &legacy_data[nr_legacy_host]; + struct ata_probe_ent ae; + struct platform_device *pdev; + int ret = -EBUSY; + struct ata_port_operations *ops = &legacy_port_ops; + int pio_modes = pio_mask; + u32 mask = (1 << port); + + if (request_region(io, 8, "pata_legacy") == NULL) + return -EBUSY; + if (request_region(ctrl, 1, "pata_legacy") == NULL) + goto fail_io; + + pdev = platform_device_register_simple(DRV_NAME, nr_legacy_host, NULL, 0); + if (pdev == NULL) + goto fail_dev; + + if (ht6560a & mask) { + ops = &ht6560a_port_ops; + pio_modes = 0x07; + } + if (ht6560b & mask) { + ops = &ht6560b_port_ops; + pio_modes = 0x1F; + } + if (opti82c611a & mask) { + ops = &opti82c611a_port_ops; + pio_modes = 0x0F; + } + if (opti82c46x & mask) { + ops = &opti82c46x_port_ops; + pio_modes = 0x0F; + } + + /* Probe for automatically detectable controllers */ + + if (io == 0x1F0 && ops == &legacy_port_ops) { + unsigned long flags; + + local_irq_save(flags); + + /* Probes */ + inb(0x1F5); + outb(inb(0x1F2) | 0x80, 0x1F2); + inb(0x1F2); + inb(0x3F6); + inb(0x3F6); + inb(0x1F2); + inb(0x1F2); + + if ((inb(0x1F2) & 0x80) == 0) { + /* PDC20230c or 20630 ? */ + printk(KERN_INFO "PDC20230-C/20630 VLB ATA controller detected.\n"); + pio_modes = 0x07; + ops = &pdc20230_port_ops; + udelay(100); + inb(0x1F5); + } else { + outb(0x55, 0x1F2); + inb(0x1F2); + inb(0x1F2); + if (inb(0x1F2) == 0x00) { + printk(KERN_INFO "PDC20230-B VLB ATA controller detected.\n"); + } + } + local_irq_restore(flags); + } + + + /* Chip does mode setting by command snooping */ + if (ops == &legacy_port_ops && (autospeed & mask)) + ops = &simple_port_ops; + memset(&ae, 0, sizeof(struct ata_probe_ent)); + INIT_LIST_HEAD(&ae.node); + ae.dev = &pdev->dev; + ae.port_ops = ops; + ae.sht = &legacy_sht; + ae.n_ports = 1; + ae.pio_mask = pio_modes; + ae.irq = irq; + ae.irq_flags = 0; + ae.port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST; + ae.port[0].cmd_addr = io; + ae.port[0].altstatus_addr = ctrl; + ae.port[0].ctl_addr = ctrl; + ata_std_ports(&ae.port[0]); + ae.private_data = ld; + + ret = ata_device_add(&ae); + if (ret == 0) { + ret = -ENODEV; + goto fail; + } + legacy_host[nr_legacy_host++] = dev_get_drvdata(&pdev->dev); + ld->platform_dev = pdev; + return 0; + +fail: + platform_device_unregister(pdev); +fail_dev: + release_region(ctrl, 1); +fail_io: + release_region(io, 8); + return ret; +} + +/** + * legacy_check_special_cases - ATA special cases + * @p: PCI device to check + * @master: set this if we find an ATA master + * @master: set this if we find an ATA secondary + * + * A small number of vendors implemented early PCI ATA interfaces on bridge logic + * without the ATA interface being PCI visible. Where we have a matching PCI driver + * we must skip the relevant device here. If we don't know about it then the legacy + * driver is the right driver anyway. + */ + +static void legacy_check_special_cases(struct pci_dev *p, int *primary, int *secondary) +{ + /* Cyrix CS5510 pre SFF MWDMA ATA on the bridge */ + if (p->vendor == 0x1078 && p->device == 0x0000) { + *primary = *secondary = 1; + return; + } + /* Cyrix CS5520 pre SFF MWDMA ATA on the bridge */ + if (p->vendor == 0x1078 && p->device == 0x0002) { + *primary = *secondary = 1; + return; + } + /* Intel MPIIX - PIO ATA on non PCI side of bridge */ + if (p->vendor == 0x8086 && p->device == 0x1234) { + u16 r; + pci_read_config_word(p, 0x6C, &r); + if (r & 0x8000) { /* ATA port enabled */ + if (r & 0x4000) + *secondary = 1; + else + *primary = 1; + } + return; + } +} + + +/** + * legacy_init - attach legacy interfaces + * + * Attach legacy IDE interfaces by scanning the usual IRQ/port suspects. + * Right now we do not scan the ide0 and ide1 address but should do so + * for non PCI systems or systems with no PCI IDE legacy mode devices. + * If you fix that note there are special cases to consider like VLB + * drivers and CS5510/20. + */ + +static __init int legacy_init(void) +{ + int i; + int ct = 0; + int primary = 0; + int secondary = 0; + int last_port = NR_HOST; + + struct pci_dev *p = NULL; + + for_each_pci_dev(p) { + int r; + /* Check for any overlap of the system ATA mappings. Native mode controllers + stuck on these addresses or some devices in 'raid' mode won't be found by + the storage class test */ + for (r = 0; r < 6; r++) { + if (pci_resource_start(p, r) == 0x1f0) + primary = 1; + if (pci_resource_start(p, r) == 0x170) + secondary = 1; + } + /* Check for special cases */ + legacy_check_special_cases(p, &primary, &secondary); + + /* If PCI bus is present then don't probe for tertiary legacy ports */ + if (probe_all == 0) + last_port = 2; + } + + /* If an OPTI 82C46X is present find out where the channels are */ + if (opti82c46x) { + static const char *optis[4] = { + "3/463MV", "5MV", + "5MVA", "5MVB" + }; + u8 chans = 1; + u8 ctrl = (opti_syscfg(0x30) & 0xC0) >> 6; + + opti82c46x = 3; /* Assume master and slave first */ + printk(KERN_INFO DRV_NAME ": Opti 82C46%s chipset support.\n", optis[ctrl]); + if (ctrl == 3) + chans = (opti_syscfg(0x3F) & 0x20) ? 2 : 1; + ctrl = opti_syscfg(0xAC); + /* Check enabled and this port is the 465MV port. On the + MVB we may have two channels */ + if (ctrl & 8) { + if (ctrl & 4) + opti82c46x = 2; /* Slave */ + else + opti82c46x = 1; /* Master */ + if (chans == 2) + opti82c46x = 3; /* Master and Slave */ + } /* Slave only */ + else if (chans == 1) + opti82c46x = 1; + } + + for (i = 0; i < last_port; i++) { + /* Skip primary if we have seen a PCI one */ + if (i == 0 && primary == 1) + continue; + /* Skip secondary if we have seen a PCI one */ + if (i == 1 && secondary == 1) + continue; + if (legacy_init_one(i, legacy_port[i], + legacy_port[i] + 0x0206, + legacy_irq[i]) == 0) + ct++; + } + if (ct != 0) + return 0; + return -ENODEV; +} + +static __exit void legacy_exit(void) +{ + int i; + + for (i = 0; i < nr_legacy_host; i++) { + struct legacy_data *ld = &legacy_data[i]; + struct ata_port *ap =legacy_host[i]->ports[0]; + unsigned long io = ap->ioaddr.cmd_addr; + unsigned long ctrl = ap->ioaddr.ctl_addr; + ata_host_remove(legacy_host[i]); + platform_device_unregister(ld->platform_dev); + if (ld->timing) + release_region(ld->timing, 2); + release_region(io, 8); + release_region(ctrl, 1); + } +} + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for legacy ATA"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); + +module_param(probe_all, int, 0); +module_param(autospeed, int, 0); +module_param(ht6560a, int, 0); +module_param(ht6560b, int, 0); +module_param(opti82c611a, int, 0); +module_param(opti82c46x, int, 0); +module_param(pio_mask, int, 0); + +module_init(legacy_init); +module_exit(legacy_exit); + diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c new file mode 100644 index 00000000000..3c65393c1f0 --- /dev/null +++ b/drivers/ata/pata_mpiix.c @@ -0,0 +1,310 @@ +/* + * pata_mpiix.c - Intel MPIIX PATA for new ATA layer + * (C) 2005-2006 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * The MPIIX is different enough to the PIIX4 and friends that we give it + * a separate driver. The old ide/pci code handles this by just not tuning + * MPIIX at all. + * + * The MPIIX also differs in another important way from the majority of PIIX + * devices. The chip is a bridge (pardon the pun) between the old world of + * ISA IDE and PCI IDE. Although the ATA timings are PCI configured the actual + * IDE controller is not decoded in PCI space and the chip does not claim to + * be IDE class PCI. This requires slightly non-standard probe logic compared + * with PCI IDE and also that we do not disable the device when our driver is + * unloaded (as it has many other functions). + * + * The driver conciously keeps this logic internally to avoid pushing quirky + * PATA history into the clean libata layer. + * + * Thinkpad specific note: If you boot an MPIIX using a thinkpad with a PCMCIA + * hard disk present this driver will not detect it. This is not a bug. In this + * configuration the secondary port of the MPIIX is disabled and the addresses + * are decoded by the PCMCIA bridge and therefore are for a generic IDE driver + * to operate. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_mpiix" +#define DRV_VERSION "0.7.2" + +enum { + IDETIM = 0x6C, /* IDE control register */ + IORDY = (1 << 1), + PPE = (1 << 2), + FTIM = (1 << 0), + ENABLED = (1 << 15), + SECONDARY = (1 << 14) +}; + +static int mpiix_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits mpiix_enable_bits[] = { + { 0x6D, 1, 0x80, 0x80 }, + { 0x6F, 1, 0x80, 0x80 } + }; + + if (!pci_test_config_bits(pdev, &mpiix_enable_bits[ap->port_no])) + return -ENOENT; + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * mpiix_error_handler - probe reset + * @ap: ATA port + * + * Perform the ATA probe and bus reset sequence plus specific handling + * for this hardware. The MPIIX has the enable bits in a different place + * to PIIX4 and friends. As a pure PIO device it has no cable detect + */ + +static void mpiix_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, mpiix_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * mpiix_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. The MPIIX allows us to program the + * IORDY sample point (2-5 clocks), recovery 1-4 clocks and whether + * prefetching or iordy are used. + * + * This would get very ugly because we can only program timing for one + * device at a time, the other gets PIO0. Fortunately libata calls + * our qc_issue_prot command before a command is issued so we can + * flip the timings back and forth to reduce the pain. + */ + +static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + int control = 0; + int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 idetim; + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + pci_read_config_word(pdev, IDETIM, &idetim); + /* Mask the IORDY/TIME/PPE0 bank for this device */ + if (adev->class == ATA_DEV_ATA) + control |= PPE; /* PPE enable for disk */ + if (ata_pio_need_iordy(adev)) + control |= IORDY; /* IORDY */ + if (pio > 0) + control |= FTIM; /* This drive is on the fast timing bank */ + + /* Mask out timing and clear both TIME bank selects */ + idetim &= 0xCCEE; + idetim &= ~(0x07 << (2 * adev->devno)); + idetim |= (control << (2 * adev->devno)); + + idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8); + pci_write_config_word(pdev, IDETIM, idetim); + + /* We use ap->private_data as a pointer to the device currently + loaded for timing */ + ap->private_data = adev; +} + +/** + * mpiix_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * neccessary. Our logic also clears TIME0/TIME1 for the other device so + * that, even if we get this wrong, cycles to the other device will + * be made PIO0. + */ + +static unsigned int mpiix_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + /* If modes have been configured and the channel data is not loaded + then load it. We have to check if pio_mode is set as the core code + does not set adev->pio_mode to XFER_PIO_0 while probing as would be + logical */ + + if (adev->pio_mode && adev != ap->private_data) + mpiix_set_piomode(ap, adev); + + return ata_qc_issue_prot(qc); +} + +static struct scsi_host_template mpiix_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations mpiix_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = mpiix_set_piomode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = mpiix_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = mpiix_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + /* Single threaded by the PCI probe logic */ + static struct ata_probe_ent probe[2]; + static int printed_version; + u16 idetim; + int enabled; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); + + /* MPIIX has many functions which can be turned on or off according + to other devices present. Make sure IDE is enabled before we try + and use it */ + + pci_read_config_word(dev, IDETIM, &idetim); + if (!(idetim & ENABLED)) + return -ENODEV; + + /* We do our own plumbing to avoid leaking special cases for whacko + ancient hardware into the core code. There are two issues to + worry about. #1 The chip is a bridge so if in legacy mode and + without BARs set fools the setup. #2 If you pci_disable_device + the MPIIX your box goes castors up */ + + INIT_LIST_HEAD(&probe[0].node); + probe[0].dev = pci_dev_to_dev(dev); + probe[0].port_ops = &mpiix_port_ops; + probe[0].sht = &mpiix_sht; + probe[0].pio_mask = 0x1F; + probe[0].irq = 14; + probe[0].irq_flags = SA_SHIRQ; + probe[0].port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST; + probe[0].n_ports = 1; + probe[0].port[0].cmd_addr = 0x1F0; + probe[0].port[0].ctl_addr = 0x3F6; + probe[0].port[0].altstatus_addr = 0x3F6; + + /* The secondary lurks at different addresses but is otherwise + the same beastie */ + + INIT_LIST_HEAD(&probe[1].node); + probe[1] = probe[0]; + probe[1].irq = 15; + probe[1].port[0].cmd_addr = 0x170; + probe[1].port[0].ctl_addr = 0x376; + probe[1].port[0].altstatus_addr = 0x376; + + /* Let libata fill in the port details */ + ata_std_ports(&probe[0].port[0]); + ata_std_ports(&probe[1].port[0]); + + /* Now add the port that is active */ + enabled = (idetim & SECONDARY) ? 1 : 0; + + if (ata_device_add(&probe[enabled])) + return 0; + return -ENODEV; +} + +/** + * mpiix_remove_one - device unload + * @pdev: PCI device being removed + * + * Handle an unplug/unload event for a PCI device. Unload the + * PCI driver but do not use the default handler as we *MUST NOT* + * disable the device as it has other functions. + */ + +static void __devexit mpiix_remove_one(struct pci_dev *pdev) +{ + struct device *dev = pci_dev_to_dev(pdev); + struct ata_host *host = dev_get_drvdata(dev); + + ata_host_remove(host); + dev_set_drvdata(dev, NULL); +} + + + +static const struct pci_device_id mpiix[] = { + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX), }, + { 0, }, +}; + +static struct pci_driver mpiix_pci_driver = { + .name = DRV_NAME, + .id_table = mpiix, + .probe = mpiix_init_one, + .remove = mpiix_remove_one +}; + +static int __init mpiix_init(void) +{ + return pci_register_driver(&mpiix_pci_driver); +} + + +static void __exit mpiix_exit(void) +{ + pci_unregister_driver(&mpiix_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Intel MPIIX"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, mpiix); +MODULE_VERSION(DRV_VERSION); + +module_init(mpiix_init); +module_exit(mpiix_exit); diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c new file mode 100644 index 00000000000..76eb9c90bee --- /dev/null +++ b/drivers/ata/pata_netcell.c @@ -0,0 +1,174 @@ +/* + * pata_netcell.c - Netcell PATA driver + * + * (c) 2006 Red Hat <alan@redhat.com> + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_netcell" +#define DRV_VERSION "0.1.5" + +/** + * netcell_probe_init - check for 40/80 pin + * @ap: Port + * + * Cables are handled by the RAID controller. Report 80 pin. + */ + +static int netcell_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +/** + * netcell_probe_reset - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void netcell_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, netcell_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/* No PIO or DMA methods needed for this device */ + +static struct scsi_host_template netcell_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + /* Special handling needed if you have sector or LBA48 limits */ + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + /* Use standard CHS mapping rules */ + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations netcell_ops = { + .port_disable = ata_port_disable, + + /* Task file is PCI ATA format, use helpers */ + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = netcell_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + /* BMDMA handling is PCI ATA format, use helpers */ + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + /* IRQ-related hooks */ + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + /* Generic PATA PCI ATA helpers */ + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + + +/** + * netcell_init_one - Register Netcell ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in netcell_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int netcell_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + static struct ata_port_info info = { + .sht = &netcell_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + /* Actually we don't really care about these as the + firmware deals with it */ + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* UDMA 133 */ + .port_ops = &netcell_ops, + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + /* Any chip specific setup/optimisation/messages here */ + ata_pci_clear_simplex(pdev); + + /* And let the library code do the work */ + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id netcell_pci_tbl[] = { + { PCI_DEVICE(PCI_VENDOR_ID_NETCELL, PCI_DEVICE_ID_REVOLUTION), }, + { } /* terminate list */ +}; + +static struct pci_driver netcell_pci_driver = { + .name = DRV_NAME, + .id_table = netcell_pci_tbl, + .probe = netcell_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init netcell_init(void) +{ + return pci_register_driver(&netcell_pci_driver); +} + +static void __exit netcell_exit(void) +{ + pci_unregister_driver(&netcell_pci_driver); +} + +module_init(netcell_init); +module_exit(netcell_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for Netcell PATA RAID"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, netcell_pci_tbl); +MODULE_VERSION(DRV_VERSION); + diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c new file mode 100644 index 00000000000..2005a95f48f --- /dev/null +++ b/drivers/ata/pata_ns87410.c @@ -0,0 +1,233 @@ +/* + * pata_ns87410.c - National Semiconductor 87410 PATA for new ATA layer + * (C) 2006 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_ns87410" +#define DRV_VERSION "0.4.2" + +/** + * ns87410_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int ns87410_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits ns87410_enable_bits[] = { + { 0x43, 1, 0x08, 0x08 }, + { 0x47, 1, 0x08, 0x08 } + }; + + if (!pci_test_config_bits(pdev, &ns87410_enable_bits[ap->port_no])) + return -ENOENT; + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * ns87410_error_handler - probe reset + * @ap: ATA port + * + * Perform the ATA probe and bus reset sequence plus specific handling + * for this hardware. The MPIIX has the enable bits in a different place + * to PIIX4 and friends. As a pure PIO device it has no cable detect + */ + +static void ns87410_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, ns87410_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * ns87410_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program timing data. This is kept per channel not per device, + * and only affects the data port. + */ + +static void ns87410_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x40 + 4 * ap->port_no; + u8 idetcr, idefr; + struct ata_timing at; + + static const u8 activebits[15] = { + 0, 1, 2, 3, 4, + 5, 5, 6, 6, 6, + 6, 7, 7, 7, 7 + }; + + static const u8 recoverbits[12] = { + 0, 1, 2, 3, 4, 5, 6, 6, 7, 7, 7, 7 + }; + + pci_read_config_byte(pdev, port + 3, &idefr); + + if (ata_pio_need_iordy(adev)) + idefr |= 0x04; /* IORDY enable */ + else + idefr &= ~0x04; + + if (ata_timing_compute(adev, adev->pio_mode, &at, 30303, 1) < 0) { + dev_printk(KERN_ERR, &pdev->dev, "unknown mode %d.\n", adev->pio_mode); + return; + } + + at.active = FIT(at.active, 2, 16) - 2; + at.setup = FIT(at.setup, 1, 4) - 1; + at.recover = FIT(at.recover, 1, 12) - 1; + + idetcr = (at.setup << 6) | (recoverbits[at.recover] << 3) | activebits[at.active]; + + pci_write_config_byte(pdev, port, idetcr); + pci_write_config_byte(pdev, port + 3, idefr); + /* We use ap->private_data as a pointer to the device currently + loaded for timing */ + ap->private_data = adev; +} + +/** + * ns87410_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * neccessary. + */ + +static unsigned int ns87410_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + /* If modes have been configured and the channel data is not loaded + then load it. We have to check if pio_mode is set as the core code + does not set adev->pio_mode to XFER_PIO_0 while probing as would be + logical */ + + if (adev->pio_mode && adev != ap->private_data) + ns87410_set_piomode(ap, adev); + + return ata_qc_issue_prot(qc); +} + +static struct scsi_host_template ns87410_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations ns87410_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = ns87410_set_piomode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ns87410_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = ns87410_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &ns87410_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x0F, + .port_ops = &ns87410_port_ops + }; + static struct ata_port_info *port_info[2] = {&info, &info}; + return ata_pci_init_one(dev, port_info, 2); +} + +static const struct pci_device_id ns87410[] = { + { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410), }, + { 0, }, +}; + +static struct pci_driver ns87410_pci_driver = { + .name = DRV_NAME, + .id_table = ns87410, + .probe = ns87410_init_one, + .remove = ata_pci_remove_one +}; + +static int __init ns87410_init(void) +{ + return pci_register_driver(&ns87410_pci_driver); +} + + +static void __exit ns87410_exit(void) +{ + pci_unregister_driver(&ns87410_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Nat Semi 87410"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, ns87410); +MODULE_VERSION(DRV_VERSION); + +module_init(ns87410_init); +module_exit(ns87410_exit); diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c new file mode 100644 index 00000000000..31a285ca88d --- /dev/null +++ b/drivers/ata/pata_oldpiix.c @@ -0,0 +1,336 @@ +/* + * pata_oldpiix.c - Intel PATA/SATA controllers + * + * (C) 2005 Red Hat <alan@redhat.com> + * + * Some parts based on ata_piix.c by Jeff Garzik and others. + * + * Early PIIX differs significantly from the later PIIX as it lacks + * SITRE and the slave timing registers. This means that you have to + * set timing per channel, or be clever. Libata tells us whenever it + * does drive selection and we use this to reload the timings. + * + * Because of these behaviour differences PIIX gets its own driver module. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_oldpiix" +#define DRV_VERSION "0.5.2" + +/** + * oldpiix_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int oldpiix_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits oldpiix_enable_bits[] = { + { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ + { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ + }; + + if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no])) + return -ENOENT; + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * oldpiix_pata_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * @classes: + * + * LOCKING: + * None (inherited from caller). + */ + +static void oldpiix_pata_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, oldpiix_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * oldpiix_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *dev = to_pci_dev(ap->host->dev); + unsigned int idetm_port= ap->port_no ? 0x42 : 0x40; + u16 idetm_data; + int control = 0; + + /* + * See Intel Document 298600-004 for the timing programing rules + * for PIIX/ICH. Note that the early PIIX does not have the slave + * timing port at 0x44. + */ + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + if (pio > 2) + control |= 1; /* TIME1 enable */ + if (ata_pio_need_iordy(adev)) + control |= 2; /* IE IORDY */ + + /* Intel specifies that the PPE functionality is for disk only */ + if (adev->class == ATA_DEV_ATA) + control |= 4; /* PPE enable */ + + pci_read_config_word(dev, idetm_port, &idetm_data); + + /* Enable PPE, IE and TIME as appropriate. Clear the other + drive timing bits */ + if (adev->devno == 0) { + idetm_data &= 0xCCE0; + idetm_data |= control; + } else { + idetm_data &= 0xCC0E; + idetm_data |= (control << 4); + } + idetm_data |= (timings[pio][0] << 12) | + (timings[pio][1] << 8); + pci_write_config_word(dev, idetm_port, idetm_data); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * oldpiix_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * @isich: True if the device is an ICH and has IOCFG registers + * + * Set MWDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void oldpiix_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u8 idetm_port = ap->port_no ? 0x42 : 0x40; + u16 idetm_data; + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + /* + * MWDMA is driven by the PIO timings. We must also enable + * IORDY unconditionally along with TIME1. PPE has already + * been set when the PIO timing was set. + */ + + unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; + unsigned int control; + const unsigned int needed_pio[3] = { + XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 + }; + int pio = needed_pio[mwdma] - XFER_PIO_0; + + pci_read_config_word(dev, idetm_port, &idetm_data); + + control = 3; /* IORDY|TIME0 */ + /* Intel specifies that the PPE functionality is for disk only */ + if (adev->class == ATA_DEV_ATA) + control |= 4; /* PPE enable */ + + /* If the drive MWDMA is faster than it can do PIO then + we must force PIO into PIO0 */ + + if (adev->pio_mode < needed_pio[mwdma]) + /* Enable DMA timing only */ + control |= 8; /* PIO cycles in PIO0 */ + + /* Mask out the relevant control and timing bits we will load. Also + clear the other drive TIME register as a precaution */ + if (adev->devno == 0) { + idetm_data &= 0xCCE0; + idetm_data |= control; + } else { + idetm_data &= 0xCC0E; + idetm_data |= (control << 4); + } + idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); + pci_write_config_word(dev, idetm_port, idetm_data); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * oldpiix_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * neccessary. Our logic also clears TIME0/TIME1 for the other device so + * that, even if we get this wrong, cycles to the other device will + * be made PIO0. + */ + +static unsigned int oldpiix_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + if (adev != ap->private_data) { + if (adev->dma_mode) + oldpiix_set_dmamode(ap, adev); + else if (adev->pio_mode) + oldpiix_set_piomode(ap, adev); + } + return ata_qc_issue_prot(qc); +} + + +static struct scsi_host_template oldpiix_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations oldpiix_pata_ops = { + .port_disable = ata_port_disable, + .set_piomode = oldpiix_set_piomode, + .set_dmamode = oldpiix_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = oldpiix_pata_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = oldpiix_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + + +/** + * oldpiix_init_one - Register PIIX ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in oldpiix_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. We probe for combined mode (sigh), + * and then hand over control to libata, for it to do the rest. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + static struct ata_port_info info = { + .sht = &oldpiix_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma1-2 */ + .port_ops = &oldpiix_pata_ops, + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id oldpiix_pci_tbl[] = { + { PCI_DEVICE(0x8086, 0x1230), }, + { } /* terminate list */ +}; + +static struct pci_driver oldpiix_pci_driver = { + .name = DRV_NAME, + .id_table = oldpiix_pci_tbl, + .probe = oldpiix_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init oldpiix_init(void) +{ + return pci_register_driver(&oldpiix_pci_driver); +} + +static void __exit oldpiix_exit(void) +{ + pci_unregister_driver(&oldpiix_pci_driver); +} + + +module_init(oldpiix_init); +module_exit(oldpiix_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl); +MODULE_VERSION(DRV_VERSION); + diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c new file mode 100644 index 00000000000..57fe21f3a97 --- /dev/null +++ b/drivers/ata/pata_opti.c @@ -0,0 +1,290 @@ +/* + * pata_opti.c - ATI PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based on + * linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002 + * + * Copyright (C) 1996-1998 Linus Torvalds & authors (see below) + * + * Authors: + * Jaromir Koutek <miri@punknet.cz>, + * Jan Harkes <jaharkes@cwi.nl>, + * Mark Lord <mlord@pobox.com> + * Some parts of code are from ali14xx.c and from rz1000.c. + * + * Also consulted the FreeBSD prototype driver by Kevin Day to try + * and resolve some confusions. Further documentation can be found in + * Ralf Brown's interrupt list + * + * If you have other variants of the Opti range (Viper/Vendetta) please + * try this driver with those PCI idents and report back. For the later + * chips see the pata_optidma driver + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_opti" +#define DRV_VERSION "0.2.5" + +enum { + READ_REG = 0, /* index of Read cycle timing register */ + WRITE_REG = 1, /* index of Write cycle timing register */ + CNTRL_REG = 3, /* index of Control register */ + STRAP_REG = 5, /* index of Strap register */ + MISC_REG = 6 /* index of Miscellaneous register */ +}; + +/** + * opti_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int opti_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits opti_enable_bits[] = { + { 0x45, 1, 0x80, 0x00 }, + { 0x40, 1, 0x08, 0x00 } + }; + + if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no])) + return -ENOENT; + + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * opti_probe_reset - probe reset + * @ap: ATA port + * + * Perform the ATA probe and bus reset sequence plus specific handling + * for this hardware. The Opti needs little handling - we have no UDMA66 + * capability that needs cable detection. All we must do is check the port + * is enabled. + */ + +static void opti_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, opti_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * opti_write_reg - control register setup + * @ap: ATA port + * @value: value + * @reg: control register number + * + * The Opti uses magic 'trapdoor' register accesses to do configuration + * rather than using PCI space as other controllers do. The double inw + * on the error register activates configuration mode. We can then write + * the control register + */ + +static void opti_write_reg(struct ata_port *ap, u8 val, int reg) +{ + unsigned long regio = ap->ioaddr.cmd_addr; + + /* These 3 unlock the control register access */ + inw(regio + 1); + inw(regio + 1); + outb(3, regio + 2); + + /* Do the I/O */ + outb(val, regio + reg); + + /* Relock */ + outb(0x83, regio + 2); +} + +#if 0 +/** + * opti_read_reg - control register read + * @ap: ATA port + * @reg: control register number + * + * The Opti uses magic 'trapdoor' register accesses to do configuration + * rather than using PCI space as other controllers do. The double inw + * on the error register activates configuration mode. We can then read + * the control register + */ + +static u8 opti_read_reg(struct ata_port *ap, int reg) +{ + unsigned long regio = ap->ioaddr.cmd_addr; + u8 ret; + inw(regio + 1); + inw(regio + 1); + outb(3, regio + 2); + ret = inb(regio + reg); + outb(0x83, regio + 2); +} +#endif + +/** + * opti_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. Timing numbers are taken from + * the FreeBSD driver then pre computed to keep the code clean. There + * are two tables depending on the hardware clock speed. + */ + +static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct ata_device *pair = ata_dev_pair(adev); + int clock; + int pio = adev->pio_mode - XFER_PIO_0; + unsigned long regio = ap->ioaddr.cmd_addr; + u8 addr; + + /* Address table precomputed with prefetch off and a DCLK of 2 */ + static const u8 addr_timing[2][5] = { + { 0x30, 0x20, 0x20, 0x10, 0x10 }, + { 0x20, 0x20, 0x10, 0x10, 0x10 } + }; + static const u8 data_rec_timing[2][5] = { + { 0x6B, 0x56, 0x42, 0x32, 0x31 }, + { 0x58, 0x44, 0x32, 0x22, 0x21 } + }; + + outb(0xff, regio + 5); + clock = inw(regio + 5) & 1; + + /* + * As with many controllers the address setup time is shared + * and must suit both devices if present. + */ + + addr = addr_timing[clock][pio]; + if (pair) { + /* Hardware constraint */ + u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0]; + if (pair_addr > addr) + addr = pair_addr; + } + + /* Commence primary programming sequence */ + opti_write_reg(ap, adev->devno, MISC_REG); + opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG); + opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG); + opti_write_reg(ap, addr, MISC_REG); + + /* Programming sequence complete, override strapping */ + opti_write_reg(ap, 0x85, CNTRL_REG); +} + +static struct scsi_host_template opti_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations opti_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = opti_set_piomode, +/* .set_dmamode = opti_set_dmamode, */ + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = opti_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &opti_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .port_ops = &opti_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + static int printed_version; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); + + return ata_pci_init_one(dev, port_info, 2); +} + +static const struct pci_device_id opti[] = { + { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C621, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, + { 0, }, +}; + +static struct pci_driver opti_pci_driver = { + .name = DRV_NAME, + .id_table = opti, + .probe = opti_init_one, + .remove = ata_pci_remove_one +}; + +static int __init opti_init(void) +{ + return pci_register_driver(&opti_pci_driver); +} + + +static void __exit opti_exit(void) +{ + pci_unregister_driver(&opti_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Opti 621/621X"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, opti); +MODULE_VERSION(DRV_VERSION); + +module_init(opti_init); +module_exit(opti_exit); diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c new file mode 100644 index 00000000000..7296a20cd10 --- /dev/null +++ b/drivers/ata/pata_optidma.c @@ -0,0 +1,545 @@ +/* + * pata_optidma.c - Opti DMA PATA for new ATA layer + * (C) 2006 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * The Opti DMA controllers are related to the older PIO PCI controllers + * and indeed the VLB ones. The main differences are that the timing + * numbers are now based off PCI clocks not VLB and differ, and that + * MWDMA is supported. + * + * This driver should support Viper-N+, FireStar, FireStar Plus. + * + * These devices support virtual DMA for read (aka the CS5520). Later + * chips support UDMA33, but only if the rest of the board logic does, + * so you have to get this right. We don't support the virtual DMA + * but we do handle UDMA. + * + * Bits that are worth knowing + * Most control registers are shadowed into I/O registers + * 0x1F5 bit 0 tells you if the PCI/VLB clock is 33 or 25Mhz + * Virtual DMA registers *move* between rev 0x02 and rev 0x10 + * UDMA requires a 66MHz FSB + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_optidma" +#define DRV_VERSION "0.2.2" + +enum { + READ_REG = 0, /* index of Read cycle timing register */ + WRITE_REG = 1, /* index of Write cycle timing register */ + CNTRL_REG = 3, /* index of Control register */ + STRAP_REG = 5, /* index of Strap register */ + MISC_REG = 6 /* index of Miscellaneous register */ +}; + +static int pci_clock; /* 0 = 33 1 = 25 */ + +/** + * optidma_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int optidma_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits optidma_enable_bits = { + 0x40, 1, 0x08, 0x00 + }; + + if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits)) + return -ENOENT; + + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * optidma_probe_reset - probe reset + * @ap: ATA port + * + * Perform the ATA probe and bus reset sequence plus specific handling + * for this hardware. The Opti needs little handling - we have no UDMA66 + * capability that needs cable detection. All we must do is check the port + * is enabled. + */ + +static void optidma_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, optidma_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * optidma_unlock - unlock control registers + * @ap: ATA port + * + * Unlock the control register block for this adapter. Registers must not + * be unlocked in a situation where libata might look at them. + */ + +static void optidma_unlock(struct ata_port *ap) +{ + unsigned long regio = ap->ioaddr.cmd_addr; + + /* These 3 unlock the control register access */ + inw(regio + 1); + inw(regio + 1); + outb(3, regio + 2); +} + +/** + * optidma_lock - issue temporary relock + * @ap: ATA port + * + * Re-lock the configuration register settings. + */ + +static void optidma_lock(struct ata_port *ap) +{ + unsigned long regio = ap->ioaddr.cmd_addr; + + /* Relock */ + outb(0x83, regio + 2); +} + +/** + * optidma_set_mode - set mode data + * @ap: ATA interface + * @adev: ATA device + * @mode: Mode to set + * + * Called to do the DMA or PIO mode setup. Timing numbers are all + * pre computed to keep the code clean. There are two tables depending + * on the hardware clock speed. + * + * WARNING: While we do this the IDE registers vanish. If we take an + * IRQ here we depend on the host set locking to avoid catastrophe. + */ + +static void optidma_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode) +{ + struct ata_device *pair = ata_dev_pair(adev); + int pio = adev->pio_mode - XFER_PIO_0; + int dma = adev->dma_mode - XFER_MW_DMA_0; + unsigned long regio = ap->ioaddr.cmd_addr; + u8 addr; + + /* Address table precomputed with a DCLK of 2 */ + static const u8 addr_timing[2][5] = { + { 0x30, 0x20, 0x20, 0x10, 0x10 }, + { 0x20, 0x20, 0x10, 0x10, 0x10 } + }; + static const u8 data_rec_timing[2][5] = { + { 0x59, 0x46, 0x30, 0x20, 0x20 }, + { 0x46, 0x32, 0x20, 0x20, 0x10 } + }; + static const u8 dma_data_rec_timing[2][3] = { + { 0x76, 0x20, 0x20 }, + { 0x54, 0x20, 0x10 } + }; + + /* Switch from IDE to control mode */ + optidma_unlock(ap); + + + /* + * As with many controllers the address setup time is shared + * and must suit both devices if present. FIXME: Check if we + * need to look at slowest of PIO/DMA mode of either device + */ + + if (mode >= XFER_MW_DMA_0) + addr = 0; + else + addr = addr_timing[pci_clock][pio]; + + if (pair) { + u8 pair_addr; + /* Hardware constraint */ + if (pair->dma_mode) + pair_addr = 0; + else + pair_addr = addr_timing[pci_clock][pair->pio_mode - XFER_PIO_0]; + if (pair_addr > addr) + addr = pair_addr; + } + + /* Commence primary programming sequence */ + /* First we load the device number into the timing select */ + outb(adev->devno, regio + MISC_REG); + /* Now we load the data timings into read data/write data */ + if (mode < XFER_MW_DMA_0) { + outb(data_rec_timing[pci_clock][pio], regio + READ_REG); + outb(data_rec_timing[pci_clock][pio], regio + WRITE_REG); + } else if (mode < XFER_UDMA_0) { + outb(dma_data_rec_timing[pci_clock][dma], regio + READ_REG); + outb(dma_data_rec_timing[pci_clock][dma], regio + WRITE_REG); + } + /* Finally we load the address setup into the misc register */ + outb(addr | adev->devno, regio + MISC_REG); + + /* Programming sequence complete, timing 0 dev 0, timing 1 dev 1 */ + outb(0x85, regio + CNTRL_REG); + + /* Switch back to IDE mode */ + optidma_lock(ap); + + /* Note: at this point our programming is incomplete. We are + not supposed to program PCI 0x43 "things we hacked onto the chip" + until we've done both sets of PIO/DMA timings */ +} + +/** + * optiplus_set_mode - DMA setup for Firestar Plus + * @ap: ATA port + * @adev: device + * @mode: desired mode + * + * The Firestar plus has additional UDMA functionality for UDMA0-2 and + * requires we do some additional work. Because the base work we must do + * is mostly shared we wrap the Firestar setup functionality in this + * one + */ + +static void optiplus_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 udcfg; + u8 udslave; + int dev2 = 2 * adev->devno; + int unit = 2 * ap->port_no + adev->devno; + int udma = mode - XFER_UDMA_0; + + pci_read_config_byte(pdev, 0x44, &udcfg); + if (mode <= XFER_UDMA_0) { + udcfg &= ~(1 << unit); + optidma_set_mode(ap, adev, adev->dma_mode); + } else { + udcfg |= (1 << unit); + if (ap->port_no) { + pci_read_config_byte(pdev, 0x45, &udslave); + udslave &= ~(0x03 << dev2); + udslave |= (udma << dev2); + pci_write_config_byte(pdev, 0x45, udslave); + } else { + udcfg &= ~(0x30 << dev2); + udcfg |= (udma << dev2); + } + } + pci_write_config_byte(pdev, 0x44, udcfg); +} + +/** + * optidma_set_pio_mode - PIO setup callback + * @ap: ATA port + * @adev: Device + * + * The libata core provides separate functions for handling PIO and + * DMA programming. The architecture of the Firestar makes it easier + * for us to have a common function so we provide wrappers + */ + +static void optidma_set_pio_mode(struct ata_port *ap, struct ata_device *adev) +{ + optidma_set_mode(ap, adev, adev->pio_mode); +} + +/** + * optidma_set_dma_mode - DMA setup callback + * @ap: ATA port + * @adev: Device + * + * The libata core provides separate functions for handling PIO and + * DMA programming. The architecture of the Firestar makes it easier + * for us to have a common function so we provide wrappers + */ + +static void optidma_set_dma_mode(struct ata_port *ap, struct ata_device *adev) +{ + optidma_set_mode(ap, adev, adev->dma_mode); +} + +/** + * optiplus_set_pio_mode - PIO setup callback + * @ap: ATA port + * @adev: Device + * + * The libata core provides separate functions for handling PIO and + * DMA programming. The architecture of the Firestar makes it easier + * for us to have a common function so we provide wrappers + */ + +static void optiplus_set_pio_mode(struct ata_port *ap, struct ata_device *adev) +{ + optiplus_set_mode(ap, adev, adev->pio_mode); +} + +/** + * optiplus_set_dma_mode - DMA setup callback + * @ap: ATA port + * @adev: Device + * + * The libata core provides separate functions for handling PIO and + * DMA programming. The architecture of the Firestar makes it easier + * for us to have a common function so we provide wrappers + */ + +static void optiplus_set_dma_mode(struct ata_port *ap, struct ata_device *adev) +{ + optiplus_set_mode(ap, adev, adev->dma_mode); +} + +/** + * optidma_make_bits - PCI setup helper + * @adev: ATA device + * + * Turn the ATA device setup into PCI configuration bits + * for register 0x43 and return the two bits needed. + */ + +static u8 optidma_make_bits43(struct ata_device *adev) +{ + static const u8 bits43[5] = { + 0, 0, 0, 1, 2 + }; + if (!ata_dev_enabled(adev)) + return 0; + if (adev->dma_mode) + return adev->dma_mode - XFER_MW_DMA_0; + return bits43[adev->pio_mode - XFER_PIO_0]; +} + +/** + * optidma_post_set_mode - finalize PCI setup + * @ap: port to set up + * + * Finalise the configuration by writing the nibble of extra bits + * of data into the chip. + */ + +static void optidma_post_set_mode(struct ata_port *ap) +{ + u8 r; + int nybble = 4 * ap->port_no; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x43, &r); + + r &= (0x0F << nybble); + r |= (optidma_make_bits43(&ap->device[0]) + + (optidma_make_bits43(&ap->device[0]) << 2)) << nybble; + + pci_write_config_byte(pdev, 0x43, r); +} + +static struct scsi_host_template optidma_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations optidma_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = optidma_set_pio_mode, + .set_dmamode = optidma_set_dma_mode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .error_handler = optidma_error_handler, + .post_set_mode = optidma_post_set_mode, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations optiplus_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = optiplus_set_pio_mode, + .set_dmamode = optiplus_set_dma_mode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .error_handler = optidma_error_handler, + .post_set_mode = optidma_post_set_mode, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * optiplus_with_udma - Look for UDMA capable setup + * @pdev; ATA controller + */ + +static int optiplus_with_udma(struct pci_dev *pdev) +{ + u8 r; + int ret = 0; + int ioport = 0x22; + struct pci_dev *dev1; + + /* Find function 1 */ + dev1 = pci_get_device(0x1045, 0xC701, NULL); + if(dev1 == NULL) + return 0; + + /* Rev must be >= 0x10 */ + pci_read_config_byte(dev1, 0x08, &r); + if (r < 0x10) + goto done_nomsg; + /* Read the chipset system configuration to check our mode */ + pci_read_config_byte(dev1, 0x5F, &r); + ioport |= (r << 8); + outb(0x10, ioport); + /* Must be 66Mhz sync */ + if ((inb(ioport + 2) & 1) == 0) + goto done; + + /* Check the ATA arbitration/timing is suitable */ + pci_read_config_byte(pdev, 0x42, &r); + if ((r & 0x36) != 0x36) + goto done; + pci_read_config_byte(dev1, 0x52, &r); + if (r & 0x80) /* IDEDIR disabled */ + ret = 1; +done: + printk(KERN_WARNING "UDMA not supported in this configuration.\n"); +done_nomsg: /* Wrong chip revision */ + pci_dev_put(dev1); + return ret; +} + +static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info_82c700 = { + .sht = &optidma_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &optidma_port_ops + }; + static struct ata_port_info info_82c700_udma = { + .sht = &optidma_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, + .port_ops = &optiplus_port_ops + }; + static struct ata_port_info *port_info[2]; + struct ata_port_info *info = &info_82c700; + static int printed_version; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); + + /* Fixed location chipset magic */ + inw(0x1F1); + inw(0x1F1); + pci_clock = inb(0x1F5) & 1; /* 0 = 33Mhz, 1 = 25Mhz */ + + if (optiplus_with_udma(dev)) + info = &info_82c700_udma; + + port_info[0] = port_info[1] = info; + return ata_pci_init_one(dev, port_info, 2); +} + +static const struct pci_device_id optidma[] = { + { PCI_DEVICE(0x1045, 0xD568), }, /* Opti 82C700 */ + { 0, }, +}; + +static struct pci_driver optidma_pci_driver = { + .name = DRV_NAME, + .id_table = optidma, + .probe = optidma_init_one, + .remove = ata_pci_remove_one +}; + +static int __init optidma_init(void) +{ + return pci_register_driver(&optidma_pci_driver); +} + + +static void __exit optidma_exit(void) +{ + pci_unregister_driver(&optidma_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Opti Firestar/Firestar Plus"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, optidma); +MODULE_VERSION(DRV_VERSION); + +module_init(optidma_init); +module_exit(optidma_exit); diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c new file mode 100644 index 00000000000..cb501e145a4 --- /dev/null +++ b/drivers/ata/pata_pcmcia.c @@ -0,0 +1,393 @@ +/* + * pata_pcmcia.c - PCMCIA PATA controller driver. + * Copyright 2005-2006 Red Hat Inc <alan@redhat.com>, all rights reserved. + * PCMCIA ident update Copyright 2006 Marcin Juszkiewicz + * <openembedded@hrw.one.pl> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * Heavily based upon ide-cs.c + * The initial developer of the original code is David A. Hinds + * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds + * are Copyright (C) 1999 David A. Hinds. All Rights Reserved. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/ata.h> +#include <linux/libata.h> + +#include <pcmcia/cs_types.h> +#include <pcmcia/cs.h> +#include <pcmcia/cistpl.h> +#include <pcmcia/ds.h> +#include <pcmcia/cisreg.h> +#include <pcmcia/ciscode.h> + + +#define DRV_NAME "pata_pcmcia" +#define DRV_VERSION "0.2.9" + +/* + * Private data structure to glue stuff together + */ + +struct ata_pcmcia_info { + struct pcmcia_device *pdev; + int ndev; + dev_node_t node; +}; + +static struct scsi_host_template pcmcia_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations pcmcia_port_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer_noirq, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +#define CS_CHECK(fn, ret) \ +do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0) + +/** + * pcmcia_init_one - attach a PCMCIA interface + * @pdev: pcmcia device + * + * Register a PCMCIA IDE interface. Such interfaces are PIO 0 and + * shared IRQ. + */ + +static int pcmcia_init_one(struct pcmcia_device *pdev) +{ + struct ata_probe_ent ae; + struct ata_pcmcia_info *info; + tuple_t tuple; + struct { + unsigned short buf[128]; + cisparse_t parse; + config_info_t conf; + cistpl_cftable_entry_t dflt; + } *stk = NULL; + cistpl_cftable_entry_t *cfg; + int pass, last_ret = 0, last_fn = 0, is_kme = 0, ret = -ENOMEM; + unsigned long io_base, ctl_base; + + info = kzalloc(sizeof(*info), GFP_KERNEL); + if (info == NULL) + return -ENOMEM; + + /* Glue stuff together. FIXME: We may be able to get rid of info with care */ + info->pdev = pdev; + pdev->priv = info; + + /* Set up attributes in order to probe card and get resources */ + pdev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; + pdev->io.Attributes2 = IO_DATA_PATH_WIDTH_8; + pdev->io.IOAddrLines = 3; + pdev->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING; + pdev->irq.IRQInfo1 = IRQ_LEVEL_ID; + pdev->conf.Attributes = CONF_ENABLE_IRQ; + pdev->conf.IntType = INT_MEMORY_AND_IO; + + /* Allocate resoure probing structures */ + + stk = kzalloc(sizeof(*stk), GFP_KERNEL); + if (!stk) + goto out1; + + cfg = &stk->parse.cftable_entry; + + /* Tuples we are walking */ + tuple.TupleData = (cisdata_t *)&stk->buf; + tuple.TupleOffset = 0; + tuple.TupleDataMax = 255; + tuple.Attributes = 0; + tuple.DesiredTuple = CISTPL_CONFIG; + + CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(pdev, &tuple)); + CS_CHECK(GetTupleData, pcmcia_get_tuple_data(pdev, &tuple)); + CS_CHECK(ParseTuple, pcmcia_parse_tuple(pdev, &tuple, &stk->parse)); + pdev->conf.ConfigBase = stk->parse.config.base; + pdev->conf.Present = stk->parse.config.rmask[0]; + + /* See if we have a manufacturer identifier. Use it to set is_kme for + vendor quirks */ + tuple.DesiredTuple = CISTPL_MANFID; + if (!pcmcia_get_first_tuple(pdev, &tuple) && !pcmcia_get_tuple_data(pdev, &tuple) && !pcmcia_parse_tuple(pdev, &tuple, &stk->parse)) + is_kme = ((stk->parse.manfid.manf == MANFID_KME) && ((stk->parse.manfid.card == PRODID_KME_KXLC005_A) || (stk->parse.manfid.card == PRODID_KME_KXLC005_B))); + + /* Not sure if this is right... look up the current Vcc */ + CS_CHECK(GetConfigurationInfo, pcmcia_get_configuration_info(pdev, &stk->conf)); +/* link->conf.Vcc = stk->conf.Vcc; */ + + pass = io_base = ctl_base = 0; + tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; + tuple.Attributes = 0; + CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(pdev, &tuple)); + + /* Now munch the resources looking for a suitable set */ + while (1) { + if (pcmcia_get_tuple_data(pdev, &tuple) != 0) + goto next_entry; + if (pcmcia_parse_tuple(pdev, &tuple, &stk->parse) != 0) + goto next_entry; + /* Check for matching Vcc, unless we're desperate */ + if (!pass) { + if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (stk->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) + goto next_entry; + } else if (stk->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (stk->conf.Vcc != stk->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) + goto next_entry; + } + } + + if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) + pdev->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; + else if (stk->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) + pdev->conf.Vpp = stk->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; + + if ((cfg->io.nwin > 0) || (stk->dflt.io.nwin > 0)) { + cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &stk->dflt.io; + pdev->conf.ConfigIndex = cfg->index; + pdev->io.BasePort1 = io->win[0].base; + pdev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; + if (!(io->flags & CISTPL_IO_16BIT)) + pdev->io.Attributes1 = IO_DATA_PATH_WIDTH_8; + if (io->nwin == 2) { + pdev->io.NumPorts1 = 8; + pdev->io.BasePort2 = io->win[1].base; + pdev->io.NumPorts2 = (is_kme) ? 2 : 1; + if (pcmcia_request_io(pdev, &pdev->io) != 0) + goto next_entry; + io_base = pdev->io.BasePort1; + ctl_base = pdev->io.BasePort2; + } else if ((io->nwin == 1) && (io->win[0].len >= 16)) { + pdev->io.NumPorts1 = io->win[0].len; + pdev->io.NumPorts2 = 0; + if (pcmcia_request_io(pdev, &pdev->io) != 0) + goto next_entry; + io_base = pdev->io.BasePort1; + ctl_base = pdev->io.BasePort1 + 0x0e; + } else goto next_entry; + /* If we've got this far, we're done */ + break; + } +next_entry: + if (cfg->flags & CISTPL_CFTABLE_DEFAULT) + memcpy(&stk->dflt, cfg, sizeof(stk->dflt)); + if (pass) { + CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(pdev, &tuple)); + } else if (pcmcia_get_next_tuple(pdev, &tuple) != 0) { + CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(pdev, &tuple)); + memset(&stk->dflt, 0, sizeof(stk->dflt)); + pass++; + } + } + + CS_CHECK(RequestIRQ, pcmcia_request_irq(pdev, &pdev->irq)); + CS_CHECK(RequestConfiguration, pcmcia_request_configuration(pdev, &pdev->conf)); + + /* Success. Disable the IRQ nIEN line, do quirks */ + outb(0x02, ctl_base); + if (is_kme) + outb(0x81, ctl_base + 0x01); + + /* FIXME: Could be more ports at base + 0x10 but we only deal with + one right now */ + if (pdev->io.NumPorts1 >= 0x20) + printk(KERN_WARNING DRV_NAME ": second channel not yet supported.\n"); + + /* + * Having done the PCMCIA plumbing the ATA side is relatively + * sane. + */ + + memset(&ae, 0, sizeof(struct ata_probe_ent)); + INIT_LIST_HEAD(&ae.node); + ae.dev = &pdev->dev; + ae.port_ops = &pcmcia_port_ops; + ae.sht = &pcmcia_sht; + ae.n_ports = 1; + ae.pio_mask = 1; /* ISA so PIO 0 cycles */ + ae.irq = pdev->irq.AssignedIRQ; + ae.irq_flags = SA_SHIRQ; + ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST; + ae.port[0].cmd_addr = io_base; + ae.port[0].altstatus_addr = ctl_base; + ae.port[0].ctl_addr = ctl_base; + ata_std_ports(&ae.port[0]); + + if (ata_device_add(&ae) == 0) + goto failed; + + info->ndev = 1; + kfree(stk); + return 0; + +cs_failed: + cs_error(pdev, last_fn, last_ret); +failed: + kfree(stk); + info->ndev = 0; + pcmcia_disable_device(pdev); +out1: + kfree(info); + return ret; +} + +/** + * pcmcia_remove_one - unplug an pcmcia interface + * @pdev: pcmcia device + * + * A PCMCIA ATA device has been unplugged. Perform the needed + * cleanup. Also called on module unload for any active devices. + */ + +static void pcmcia_remove_one(struct pcmcia_device *pdev) +{ + struct ata_pcmcia_info *info = pdev->priv; + struct device *dev = &pdev->dev; + + if (info != NULL) { + /* If we have attached the device to the ATA layer, detach it */ + if (info->ndev) { + struct ata_host *host = dev_get_drvdata(dev); + ata_host_remove(host); + dev_set_drvdata(dev, NULL); + } + info->ndev = 0; + pdev->priv = NULL; + } + pcmcia_disable_device(pdev); + kfree(info); +} + +static struct pcmcia_device_id pcmcia_devices[] = { + PCMCIA_DEVICE_FUNC_ID(4), + PCMCIA_DEVICE_MANF_CARD(0x0007, 0x0000), /* Hitachi */ + PCMCIA_DEVICE_MANF_CARD(0x0032, 0x0704), + PCMCIA_DEVICE_MANF_CARD(0x0045, 0x0401), + PCMCIA_DEVICE_MANF_CARD(0x0098, 0x0000), /* Toshiba */ + PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x002d), + PCMCIA_DEVICE_MANF_CARD(0x00ce, 0x0000), /* Samsung */ + PCMCIA_DEVICE_MANF_CARD(0x0319, 0x0000), /* Hitachi */ + PCMCIA_DEVICE_MANF_CARD(0x2080, 0x0001), + PCMCIA_DEVICE_MANF_CARD(0x4e01, 0x0200), /* Lexar */ + PCMCIA_DEVICE_PROD_ID123("Caravelle", "PSC-IDE ", "PSC000", 0x8c36137c, 0xd0693ab8, 0x2768a9f0), + PCMCIA_DEVICE_PROD_ID123("CDROM", "IDE", "MCD-601p", 0x1b9179ca, 0xede88951, 0x0d902f74), + PCMCIA_DEVICE_PROD_ID123("PCMCIA", "IDE CARD", "F1", 0x281f1c5d, 0x1907960c, 0xf7fde8b9), + PCMCIA_DEVICE_PROD_ID12("ARGOSY", "CD-ROM", 0x78f308dc, 0x66536591), + PCMCIA_DEVICE_PROD_ID12("ARGOSY", "PnPIDE", 0x78f308dc, 0x0c694728), + PCMCIA_DEVICE_PROD_ID12("CNF CD-M", "CD-ROM", 0x7d93b852, 0x66536591), + PCMCIA_DEVICE_PROD_ID12("Creative Technology Ltd.", "PCMCIA CD-ROM Interface Card", 0xff8c8a45, 0xfe8020c4), + PCMCIA_DEVICE_PROD_ID12("Digital Equipment Corporation.", "Digital Mobile Media CD-ROM", 0x17692a66, 0xef1dcbde), + PCMCIA_DEVICE_PROD_ID12("EXP", "CD+GAME", 0x6f58c983, 0x63c13aaf), + PCMCIA_DEVICE_PROD_ID12("EXP ", "CD-ROM", 0x0a5c52fd, 0x66536591), + PCMCIA_DEVICE_PROD_ID12("EXP ", "PnPIDE", 0x0a5c52fd, 0x0c694728), + PCMCIA_DEVICE_PROD_ID12("FREECOM", "PCCARD-IDE", 0x5714cbf7, 0x48e0ab8e), + PCMCIA_DEVICE_PROD_ID12("HITACHI", "FLASH", 0xf4f43949, 0x9eb86aae), + PCMCIA_DEVICE_PROD_ID12("HITACHI", "microdrive", 0xf4f43949, 0xa6d76178), + PCMCIA_DEVICE_PROD_ID12("IBM", "microdrive", 0xb569a6e5, 0xa6d76178), + PCMCIA_DEVICE_PROD_ID12("IBM", "IBM17JSSFP20", 0xb569a6e5, 0xf2508753), + PCMCIA_DEVICE_PROD_ID12("IO DATA", "CBIDE2 ", 0x547e66dc, 0x8671043b), + PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDE", 0x547e66dc, 0x5c5ab149), + PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDEII", 0x547e66dc, 0xb3662674), + PCMCIA_DEVICE_PROD_ID12("LOOKMEET", "CBIDE2 ", 0xe37be2b5, 0x8671043b), + PCMCIA_DEVICE_PROD_ID12("M-Systems", "CF500", 0x7ed2ad87, 0x7a13045c), + PCMCIA_DEVICE_PROD_ID2("NinjaATA-", 0xebe0bd79), + PCMCIA_DEVICE_PROD_ID12("PCMCIA", "CD-ROM", 0x281f1c5d, 0x66536591), + PCMCIA_DEVICE_PROD_ID12("PCMCIA", "PnPIDE", 0x281f1c5d, 0x0c694728), + PCMCIA_DEVICE_PROD_ID12("SHUTTLE TECHNOLOGY LTD.", "PCCARD-IDE/ATAPI Adapter", 0x4a3f0ba0, 0x322560e1), + PCMCIA_DEVICE_PROD_ID12("SEAGATE", "ST1", 0x87c1b330, 0xe1f30883), + PCMCIA_DEVICE_PROD_ID12("SAMSUNG", "04/05/06", 0x43d74cb4, 0x6a22777d), + PCMCIA_DEVICE_PROD_ID12("SMI VENDOR", "SMI PRODUCT", 0x30896c92, 0x703cc5f6), + PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "MK2001MPL", 0xb4585a1a, 0x3489e003), + PCMCIA_DEVICE_PROD_ID12("WIT", "IDE16", 0x244e5994, 0x3e232852), + PCMCIA_DEVICE_PROD_ID1("STI Flash", 0xe4a13209), + PCMCIA_DEVICE_PROD_ID12("STI", "Flash 5.0", 0xbf2df18d, 0x8cb57a0e), + PCMCIA_MFC_DEVICE_PROD_ID12(1, "SanDisk", "ConnectPlus", 0x7a954bd9, 0x74be00c6), + PCMCIA_DEVICE_NULL, +}; + +MODULE_DEVICE_TABLE(pcmcia, pcmcia_devices); + +static struct pcmcia_driver pcmcia_driver = { + .owner = THIS_MODULE, + .drv = { + .name = DRV_NAME, + }, + .id_table = pcmcia_devices, + .probe = pcmcia_init_one, + .remove = pcmcia_remove_one, +}; + +static int __init pcmcia_init(void) +{ + return pcmcia_register_driver(&pcmcia_driver); +} + +static void __exit pcmcia_exit(void) +{ + pcmcia_unregister_driver(&pcmcia_driver); +} + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for PCMCIA ATA"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); + +module_init(pcmcia_init); +module_exit(pcmcia_exit); diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c new file mode 100644 index 00000000000..bd4ed6734ed --- /dev/null +++ b/drivers/ata/pata_pdc2027x.c @@ -0,0 +1,867 @@ +/* + * Promise PATA TX2/TX4/TX2000/133 IDE driver for pdc20268 to pdc20277. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * Ported to libata by: + * Albert Lee <albertcc@tw.ibm.com> IBM Corporation + * + * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org> + * Portions Copyright (C) 1999 Promise Technology, Inc. + * + * Author: Frank Tiernan (frankt@promise.com) + * Released under terms of General Public License + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware information only available under NDA. + * + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <linux/libata.h> +#include <asm/io.h> + +#define DRV_NAME "pata_pdc2027x" +#define DRV_VERSION "0.74-ac5" +#undef PDC_DEBUG + +#ifdef PDC_DEBUG +#define PDPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args) +#else +#define PDPRINTK(fmt, args...) +#endif + +enum { + PDC_UDMA_100 = 0, + PDC_UDMA_133 = 1, + + PDC_100_MHZ = 100000000, + PDC_133_MHZ = 133333333, + + PDC_SYS_CTL = 0x1100, + PDC_ATA_CTL = 0x1104, + PDC_GLOBAL_CTL = 0x1108, + PDC_CTCR0 = 0x110C, + PDC_CTCR1 = 0x1110, + PDC_BYTE_COUNT = 0x1120, + PDC_PLL_CTL = 0x1202, +}; + +static int pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); +static void pdc2027x_remove_one(struct pci_dev *pdev); +static void pdc2027x_error_handler(struct ata_port *ap); +static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev); +static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev); +static void pdc2027x_post_set_mode(struct ata_port *ap); +static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc); + +/* + * ATA Timing Tables based on 133MHz controller clock. + * These tables are only used when the controller is in 133MHz clock. + * If the controller is in 100MHz clock, the ASIC hardware will + * set the timing registers automatically when "set feature" command + * is issued to the device. However, if the controller clock is 133MHz, + * the following tables must be used. + */ +static struct pdc2027x_pio_timing { + u8 value0, value1, value2; +} pdc2027x_pio_timing_tbl [] = { + { 0xfb, 0x2b, 0xac }, /* PIO mode 0 */ + { 0x46, 0x29, 0xa4 }, /* PIO mode 1 */ + { 0x23, 0x26, 0x64 }, /* PIO mode 2 */ + { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */ + { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */ +}; + +static struct pdc2027x_mdma_timing { + u8 value0, value1; +} pdc2027x_mdma_timing_tbl [] = { + { 0xdf, 0x5f }, /* MDMA mode 0 */ + { 0x6b, 0x27 }, /* MDMA mode 1 */ + { 0x69, 0x25 }, /* MDMA mode 2 */ +}; + +static struct pdc2027x_udma_timing { + u8 value0, value1, value2; +} pdc2027x_udma_timing_tbl [] = { + { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */ + { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */ + { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */ + { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */ + { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */ + { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */ + { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */ +}; + +static const struct pci_device_id pdc2027x_pci_tbl[] = { + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20268, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20269, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20270, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20271, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20275, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20276, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20277, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 }, + { } /* terminate list */ +}; + +static struct pci_driver pdc2027x_pci_driver = { + .name = DRV_NAME, + .id_table = pdc2027x_pci_tbl, + .probe = pdc2027x_init_one, + .remove = __devexit_p(pdc2027x_remove_one), +}; + +static struct scsi_host_template pdc2027x_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations pdc2027x_pata100_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .check_atapi_dma = pdc2027x_check_atapi_dma, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2027x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static struct ata_port_operations pdc2027x_pata133_ops = { + .port_disable = ata_port_disable, + .set_piomode = pdc2027x_set_piomode, + .set_dmamode = pdc2027x_set_dmamode, + .post_set_mode = pdc2027x_post_set_mode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .check_atapi_dma = pdc2027x_check_atapi_dma, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2027x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static struct ata_port_info pdc2027x_port_info[] = { + /* PDC_UDMA_100 */ + { + .sht = &pdc2027x_sht, + .flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS | + ATA_FLAG_MMIO, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA5, /* udma0-5 */ + .port_ops = &pdc2027x_pata100_ops, + }, + /* PDC_UDMA_133 */ + { + .sht = &pdc2027x_sht, + .flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS | + ATA_FLAG_MMIO, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = ATA_UDMA6, /* udma0-6 */ + .port_ops = &pdc2027x_pata133_ops, + }, +}; + +MODULE_AUTHOR("Andre Hedrick, Frank Tiernan, Albert Lee"); +MODULE_DESCRIPTION("libata driver module for Promise PDC20268 to PDC20277"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); +MODULE_DEVICE_TABLE(pci, pdc2027x_pci_tbl); + +/** + * port_mmio - Get the MMIO address of PDC2027x extended registers + * @ap: Port + * @offset: offset from mmio base + */ +static inline void __iomem *port_mmio(struct ata_port *ap, unsigned int offset) +{ + return ap->host->mmio_base + ap->port_no * 0x100 + offset; +} + +/** + * dev_mmio - Get the MMIO address of PDC2027x extended registers + * @ap: Port + * @adev: device + * @offset: offset from mmio base + */ +static inline void __iomem *dev_mmio(struct ata_port *ap, struct ata_device *adev, unsigned int offset) +{ + u8 adj = (adev->devno) ? 0x08 : 0x00; + return port_mmio(ap, offset) + adj; +} + +/** + * pdc2027x_pata_cbl_detect - Probe host controller cable detect info + * @ap: Port for which cable detect info is desired + * + * Read 80c cable indicator from Promise extended register. + * This register is latched when the system is reset. + * + * LOCKING: + * None (inherited from caller). + */ +static void pdc2027x_cbl_detect(struct ata_port *ap) +{ + u32 cgcr; + + /* check cable detect results */ + cgcr = readl(port_mmio(ap, PDC_GLOBAL_CTL)); + if (cgcr & (1 << 26)) + goto cbl40; + + PDPRINTK("No cable or 80-conductor cable on port %d\n", ap->port_no); + + ap->cbl = ATA_CBL_PATA80; + return; + +cbl40: + printk(KERN_INFO DRV_NAME ": 40-conductor cable detected on port %d\n", ap->port_no); + ap->cbl = ATA_CBL_PATA40; + ap->udma_mask &= ATA_UDMA_MASK_40C; +} + +/** + * pdc2027x_port_enabled - Check PDC ATA control register to see whether the port is enabled. + * @ap: Port to check + */ +static inline int pdc2027x_port_enabled(struct ata_port *ap) +{ + return readb(port_mmio(ap, PDC_ATA_CTL)) & 0x02; +} + +/** + * pdc2027x_prereset - prereset for PATA host controller + * @ap: Target port + * + * Probeinit including cable detection. + * + * LOCKING: + * None (inherited from caller). + */ + +static int pdc2027x_prereset(struct ata_port *ap) +{ + /* Check whether port enabled */ + if (!pdc2027x_port_enabled(ap)) + return -ENOENT; + pdc2027x_cbl_detect(ap); + return ata_std_prereset(ap); +} + +/** + * pdc2027x_error_handler - Perform reset on PATA port and classify + * @ap: Port to reset + * + * Reset PATA phy and classify attached devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void pdc2027x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, pdc2027x_prereset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * pdc2027x_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port to configure + * @adev: um + * @pio: PIO mode, 0 - 4 + * + * Set PIO mode for device. + * + * LOCKING: + * None (inherited from caller). + */ + +static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + u32 ctcr0, ctcr1; + + PDPRINTK("adev->pio_mode[%X]\n", adev->pio_mode); + + /* Sanity check */ + if (pio > 4) { + printk(KERN_ERR DRV_NAME ": Unknown pio mode [%d] ignored\n", pio); + return; + + } + + /* Set the PIO timing registers using value table for 133MHz */ + PDPRINTK("Set pio regs... \n"); + + ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0)); + ctcr0 &= 0xffff0000; + ctcr0 |= pdc2027x_pio_timing_tbl[pio].value0 | + (pdc2027x_pio_timing_tbl[pio].value1 << 8); + writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0)); + + ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1)); + ctcr1 &= 0x00ffffff; + ctcr1 |= (pdc2027x_pio_timing_tbl[pio].value2 << 24); + writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1)); + + PDPRINTK("Set pio regs done\n"); + + PDPRINTK("Set to pio mode[%u] \n", pio); +} + +/** + * pdc2027x_set_dmamode - Initialize host controller PATA UDMA timings + * @ap: Port to configure + * @adev: um + * @udma: udma mode, XFER_UDMA_0 to XFER_UDMA_6 + * + * Set UDMA mode for device. + * + * LOCKING: + * None (inherited from caller). + */ +static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + unsigned int dma_mode = adev->dma_mode; + u32 ctcr0, ctcr1; + + if ((dma_mode >= XFER_UDMA_0) && + (dma_mode <= XFER_UDMA_6)) { + /* Set the UDMA timing registers with value table for 133MHz */ + unsigned int udma_mode = dma_mode & 0x07; + + if (dma_mode == XFER_UDMA_2) { + /* + * Turn off tHOLD. + * If tHOLD is '1', the hardware will add half clock for data hold time. + * This code segment seems to be no effect. tHOLD will be overwritten below. + */ + ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1)); + writel(ctcr1 & ~(1 << 7), dev_mmio(ap, adev, PDC_CTCR1)); + } + + PDPRINTK("Set udma regs... \n"); + + ctcr1 = readl(dev_mmio(ap, adev, PDC_CTCR1)); + ctcr1 &= 0xff000000; + ctcr1 |= pdc2027x_udma_timing_tbl[udma_mode].value0 | + (pdc2027x_udma_timing_tbl[udma_mode].value1 << 8) | + (pdc2027x_udma_timing_tbl[udma_mode].value2 << 16); + writel(ctcr1, dev_mmio(ap, adev, PDC_CTCR1)); + + PDPRINTK("Set udma regs done\n"); + + PDPRINTK("Set to udma mode[%u] \n", udma_mode); + + } else if ((dma_mode >= XFER_MW_DMA_0) && + (dma_mode <= XFER_MW_DMA_2)) { + /* Set the MDMA timing registers with value table for 133MHz */ + unsigned int mdma_mode = dma_mode & 0x07; + + PDPRINTK("Set mdma regs... \n"); + ctcr0 = readl(dev_mmio(ap, adev, PDC_CTCR0)); + + ctcr0 &= 0x0000ffff; + ctcr0 |= (pdc2027x_mdma_timing_tbl[mdma_mode].value0 << 16) | + (pdc2027x_mdma_timing_tbl[mdma_mode].value1 << 24); + + writel(ctcr0, dev_mmio(ap, adev, PDC_CTCR0)); + PDPRINTK("Set mdma regs done\n"); + + PDPRINTK("Set to mdma mode[%u] \n", mdma_mode); + } else { + printk(KERN_ERR DRV_NAME ": Unknown dma mode [%u] ignored\n", dma_mode); + } +} + +/** + * pdc2027x_post_set_mode - Set the timing registers back to correct values. + * @ap: Port to configure + * + * The pdc2027x hardware will look at "SET FEATURES" and change the timing registers + * automatically. The values set by the hardware might be incorrect, under 133Mhz PLL. + * This function overwrites the possibly incorrect values set by the hardware to be correct. + */ +static void pdc2027x_post_set_mode(struct ata_port *ap) +{ + int i; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + + if (ata_dev_enabled(dev)) { + + pdc2027x_set_piomode(ap, dev); + + /* + * Enable prefetch if the device support PIO only. + */ + if (dev->xfer_shift == ATA_SHIFT_PIO) { + u32 ctcr1 = readl(dev_mmio(ap, dev, PDC_CTCR1)); + ctcr1 |= (1 << 25); + writel(ctcr1, dev_mmio(ap, dev, PDC_CTCR1)); + + PDPRINTK("Turn on prefetch\n"); + } else { + pdc2027x_set_dmamode(ap, dev); + } + } + } +} + +/** + * pdc2027x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command + * @qc: Metadata associated with taskfile to check + * + * LOCKING: + * None (inherited from caller). + * + * RETURNS: 0 when ATAPI DMA can be used + * 1 otherwise + */ +static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *cmd = qc->scsicmd; + u8 *scsicmd = cmd->cmnd; + int rc = 1; /* atapi dma off by default */ + + /* + * This workaround is from Promise's GPL driver. + * If ATAPI DMA is used for commands not in the + * following white list, say MODE_SENSE and REQUEST_SENSE, + * pdc2027x might hit the irq lost problem. + */ + switch (scsicmd[0]) { + case READ_10: + case WRITE_10: + case READ_12: + case WRITE_12: + case READ_6: + case WRITE_6: + case 0xad: /* READ_DVD_STRUCTURE */ + case 0xbe: /* READ_CD */ + /* ATAPI DMA is ok */ + rc = 0; + break; + default: + ; + } + + return rc; +} + +/** + * pdc_read_counter - Read the ctr counter + * @probe_ent: for the port address + */ + +static long pdc_read_counter(struct ata_probe_ent *probe_ent) +{ + long counter; + int retry = 1; + u32 bccrl, bccrh, bccrlv, bccrhv; + +retry: + bccrl = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff; + bccrh = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff; + rmb(); + + /* Read the counter values again for verification */ + bccrlv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT) & 0xffff; + bccrhv = readl(probe_ent->mmio_base + PDC_BYTE_COUNT + 0x100) & 0xffff; + rmb(); + + counter = (bccrh << 15) | bccrl; + + PDPRINTK("bccrh [%X] bccrl [%X]\n", bccrh, bccrl); + PDPRINTK("bccrhv[%X] bccrlv[%X]\n", bccrhv, bccrlv); + + /* + * The 30-bit decreasing counter are read by 2 pieces. + * Incorrect value may be read when both bccrh and bccrl are changing. + * Ex. When 7900 decrease to 78FF, wrong value 7800 might be read. + */ + if (retry && !(bccrh == bccrhv && bccrl >= bccrlv)) { + retry--; + PDPRINTK("rereading counter\n"); + goto retry; + } + + return counter; +} + +/** + * adjust_pll - Adjust the PLL input clock in Hz. + * + * @pdc_controller: controller specific information + * @probe_ent: For the port address + * @pll_clock: The input of PLL in HZ + */ +static void pdc_adjust_pll(struct ata_probe_ent *probe_ent, long pll_clock, unsigned int board_idx) +{ + + u16 pll_ctl; + long pll_clock_khz = pll_clock / 1000; + long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ; + long ratio = pout_required / pll_clock_khz; + int F, R; + + /* Sanity check */ + if (unlikely(pll_clock_khz < 5000L || pll_clock_khz > 70000L)) { + printk(KERN_ERR DRV_NAME ": Invalid PLL input clock %ldkHz, give up!\n", pll_clock_khz); + return; + } + +#ifdef PDC_DEBUG + PDPRINTK("pout_required is %ld\n", pout_required); + + /* Show the current clock value of PLL control register + * (maybe already configured by the firmware) + */ + pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL); + + PDPRINTK("pll_ctl[%X]\n", pll_ctl); +#endif + + /* + * Calculate the ratio of F, R and OD + * POUT = (F + 2) / (( R + 2) * NO) + */ + if (ratio < 8600L) { /* 8.6x */ + /* Using NO = 0x01, R = 0x0D */ + R = 0x0d; + } else if (ratio < 12900L) { /* 12.9x */ + /* Using NO = 0x01, R = 0x08 */ + R = 0x08; + } else if (ratio < 16100L) { /* 16.1x */ + /* Using NO = 0x01, R = 0x06 */ + R = 0x06; + } else if (ratio < 64000L) { /* 64x */ + R = 0x00; + } else { + /* Invalid ratio */ + printk(KERN_ERR DRV_NAME ": Invalid ratio %ld, give up!\n", ratio); + return; + } + + F = (ratio * (R+2)) / 1000 - 2; + + if (unlikely(F < 0 || F > 127)) { + /* Invalid F */ + printk(KERN_ERR DRV_NAME ": F[%d] invalid!\n", F); + return; + } + + PDPRINTK("F[%d] R[%d] ratio*1000[%ld]\n", F, R, ratio); + + pll_ctl = (R << 8) | F; + + PDPRINTK("Writing pll_ctl[%X]\n", pll_ctl); + + writew(pll_ctl, probe_ent->mmio_base + PDC_PLL_CTL); + readw(probe_ent->mmio_base + PDC_PLL_CTL); /* flush */ + + /* Wait the PLL circuit to be stable */ + mdelay(30); + +#ifdef PDC_DEBUG + /* + * Show the current clock value of PLL control register + * (maybe configured by the firmware) + */ + pll_ctl = readw(probe_ent->mmio_base + PDC_PLL_CTL); + + PDPRINTK("pll_ctl[%X]\n", pll_ctl); +#endif + + return; +} + +/** + * detect_pll_input_clock - Detect the PLL input clock in Hz. + * @probe_ent: for the port address + * Ex. 16949000 on 33MHz PCI bus for pdc20275. + * Half of the PCI clock. + */ +static long pdc_detect_pll_input_clock(struct ata_probe_ent *probe_ent) +{ + u32 scr; + long start_count, end_count; + long pll_clock; + + /* Read current counter value */ + start_count = pdc_read_counter(probe_ent); + + /* Start the test mode */ + scr = readl(probe_ent->mmio_base + PDC_SYS_CTL); + PDPRINTK("scr[%X]\n", scr); + writel(scr | (0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL); + readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */ + + /* Let the counter run for 100 ms. */ + mdelay(100); + + /* Read the counter values again */ + end_count = pdc_read_counter(probe_ent); + + /* Stop the test mode */ + scr = readl(probe_ent->mmio_base + PDC_SYS_CTL); + PDPRINTK("scr[%X]\n", scr); + writel(scr & ~(0x01 << 14), probe_ent->mmio_base + PDC_SYS_CTL); + readl(probe_ent->mmio_base + PDC_SYS_CTL); /* flush */ + + /* calculate the input clock in Hz */ + pll_clock = (start_count - end_count) * 10; + + PDPRINTK("start[%ld] end[%ld] \n", start_count, end_count); + PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock); + + return pll_clock; +} + +/** + * pdc_hardware_init - Initialize the hardware. + * @pdev: instance of pci_dev found + * @pdc_controller: controller specific information + * @pe: for the port address + */ +static int pdc_hardware_init(struct pci_dev *pdev, struct ata_probe_ent *pe, unsigned int board_idx) +{ + long pll_clock; + + /* + * Detect PLL input clock rate. + * On some system, where PCI bus is running at non-standard clock rate. + * Ex. 25MHz or 40MHz, we have to adjust the cycle_time. + * The pdc20275 controller employs PLL circuit to help correct timing registers setting. + */ + pll_clock = pdc_detect_pll_input_clock(pe); + + if (pll_clock < 0) /* counter overflow? Try again. */ + pll_clock = pdc_detect_pll_input_clock(pe); + + dev_printk(KERN_INFO, &pdev->dev, "PLL input clock %ld kHz\n", pll_clock/1000); + + /* Adjust PLL control register */ + pdc_adjust_pll(pe, pll_clock, board_idx); + + return 0; +} + +/** + * pdc_ata_setup_port - setup the mmio address + * @port: ata ioports to setup + * @base: base address + */ +static void pdc_ata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = + port->data_addr = base; + port->feature_addr = + port->error_addr = base + 0x05; + port->nsect_addr = base + 0x0a; + port->lbal_addr = base + 0x0f; + port->lbam_addr = base + 0x10; + port->lbah_addr = base + 0x15; + port->device_addr = base + 0x1a; + port->command_addr = + port->status_addr = base + 0x1f; + port->altstatus_addr = + port->ctl_addr = base + 0x81a; +} + +/** + * pdc2027x_init_one - PCI probe function + * Called when an instance of PCI adapter is inserted. + * This function checks whether the hardware is supported, + * initialize hardware and register an instance of ata_host to + * libata by providing struct ata_probe_ent and ata_device_add(). + * (implements struct pci_driver.probe() ) + * + * @pdev: instance of pci_dev found + * @ent: matching entry in the id_tbl[] + */ +static int __devinit pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + unsigned int board_idx = (unsigned int) ent->driver_data; + + struct ata_probe_ent *probe_ent = NULL; + unsigned long base; + void __iomem *mmio_base; + int rc; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto err_out; + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + /* Prepare the probe entry */ + probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, 5, 0); + if (!mmio_base) { + rc = -ENOMEM; + goto err_out_free_ent; + } + + base = (unsigned long) mmio_base; + + probe_ent->sht = pdc2027x_port_info[board_idx].sht; + probe_ent->port_flags = pdc2027x_port_info[board_idx].flags; + probe_ent->pio_mask = pdc2027x_port_info[board_idx].pio_mask; + probe_ent->mwdma_mask = pdc2027x_port_info[board_idx].mwdma_mask; + probe_ent->udma_mask = pdc2027x_port_info[board_idx].udma_mask; + probe_ent->port_ops = pdc2027x_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = SA_SHIRQ; + probe_ent->mmio_base = mmio_base; + + pdc_ata_setup_port(&probe_ent->port[0], base + 0x17c0); + probe_ent->port[0].bmdma_addr = base + 0x1000; + pdc_ata_setup_port(&probe_ent->port[1], base + 0x15c0); + probe_ent->port[1].bmdma_addr = base + 0x1008; + + probe_ent->n_ports = 2; + + pci_set_master(pdev); + //pci_enable_intx(pdev); + + /* initialize adapter */ + if (pdc_hardware_init(pdev, probe_ent, board_idx) != 0) + goto err_out_free_ent; + + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + pci_disable_device(pdev); + return rc; +} + +/** + * pdc2027x_remove_one - Called to remove a single instance of the + * adapter. + * + * @dev: The PCI device to remove. + * FIXME: module load/unload not working yet + */ +static void __devexit pdc2027x_remove_one(struct pci_dev *pdev) +{ + ata_pci_remove_one(pdev); +} + +/** + * pdc2027x_init - Called after this module is loaded into the kernel. + */ +static int __init pdc2027x_init(void) +{ + return pci_module_init(&pdc2027x_pci_driver); +} + +/** + * pdc2027x_exit - Called before this module unloaded from the kernel + */ +static void __exit pdc2027x_exit(void) +{ + pci_unregister_driver(&pdc2027x_pci_driver); +} + +module_init(pdc2027x_init); +module_exit(pdc2027x_exit); diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c new file mode 100644 index 00000000000..48f43432764 --- /dev/null +++ b/drivers/ata/pata_pdc202xx_old.c @@ -0,0 +1,423 @@ +/* + * pata_pdc202xx_old.c - Promise PDC202xx PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based in part on linux/drivers/ide/pci/pdc202xx_old.c + * + * First cut with LBA48/ATAPI + * + * TODO: + * Channel interlock/reset on both required ? + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_pdc202xx_old" +#define DRV_VERSION "0.2.1" + +/** + * pdc2024x_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int pdc2024x_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + + +static void pdc2024x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, pdc2024x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + + +static int pdc2026x_pre_reset(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 cis; + + pci_read_config_word(pdev, 0x50, &cis); + if (cis & (1 << (10 + ap->port_no))) + ap->cbl = ATA_CBL_PATA80; + else + ap->cbl = ATA_CBL_PATA40; + + return ata_std_prereset(ap); +} + +static void pdc2026x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, pdc2026x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * pdc_configure_piomode - set chip PIO timing + * @ap: ATA interface + * @adev: ATA device + * @pio: PIO mode + * + * Called to do the PIO mode setup. Our timing registers are shared + * so a configure_dmamode call will undo any work we do here and vice + * versa + */ + +static void pdc_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x60 + 4 * ap->port_no + 2 * adev->devno; + static u16 pio_timing[5] = { + 0x0913, 0x050C , 0x0308, 0x0206, 0x0104 + }; + u8 r_ap, r_bp; + + pci_read_config_byte(pdev, port, &r_ap); + pci_read_config_byte(pdev, port + 1, &r_bp); + r_ap &= ~0x3F; /* Preserve ERRDY_EN, SYNC_IN */ + r_bp &= ~0x07; + r_ap |= (pio_timing[pio] >> 8); + r_bp |= (pio_timing[pio] & 0xFF); + + if (ata_pio_need_iordy(adev)) + r_ap |= 0x20; /* IORDY enable */ + if (adev->class == ATA_DEV_ATA) + r_ap |= 0x10; /* FIFO enable */ + pci_write_config_byte(pdev, port, r_ap); + pci_write_config_byte(pdev, port + 1, r_bp); +} + +/** + * pdc_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. Our timing registers are shared + * but we want to set the PIO timing by default. + */ + +static void pdc_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + pdc_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); +} + +/** + * pdc_configure_dmamode - set DMA mode in chip + * @ap: ATA interface + * @adev: ATA device + * + * Load DMA cycle times into the chip ready for a DMA transfer + * to occur. + */ + +static void pdc_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x60 + 4 * ap->port_no + 2 * adev->devno; + static u8 udma_timing[6][2] = { + { 0x60, 0x03 }, /* 33 Mhz Clock */ + { 0x40, 0x02 }, + { 0x20, 0x01 }, + { 0x40, 0x02 }, /* 66 Mhz Clock */ + { 0x20, 0x01 }, + { 0x20, 0x01 } + }; + u8 r_bp, r_cp; + + pci_read_config_byte(pdev, port + 1, &r_bp); + pci_read_config_byte(pdev, port + 2, &r_cp); + + r_bp &= ~0xF0; + r_cp &= ~0x0F; + + if (adev->dma_mode >= XFER_UDMA_0) { + int speed = adev->dma_mode - XFER_UDMA_0; + r_bp |= udma_timing[speed][0]; + r_cp |= udma_timing[speed][1]; + + } else { + int speed = adev->dma_mode - XFER_MW_DMA_0; + r_bp |= 0x60; + r_cp |= (5 - speed); + } + pci_write_config_byte(pdev, port + 1, r_bp); + pci_write_config_byte(pdev, port + 2, r_cp); + +} + +/** + * pdc2026x_bmdma_start - DMA engine begin + * @qc: ATA command + * + * In UDMA3 or higher we have to clock switch for the duration of the + * DMA transfer sequence. + */ + +static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_taskfile *tf = &qc->tf; + int sel66 = ap->port_no ? 0x08: 0x02; + + unsigned long master = ap->host->ports[0]->ioaddr.bmdma_addr; + unsigned long clock = master + 0x11; + unsigned long atapi_reg = master + 0x20 + (4 * ap->port_no); + + u32 len; + + /* Check we keep host level locking here */ + if (adev->dma_mode >= XFER_UDMA_2) + outb(inb(clock) | sel66, clock); + else + outb(inb(clock) & ~sel66, clock); + + /* The DMA clocks may have been trashed by a reset. FIXME: make conditional + and move to qc_issue ? */ + pdc_set_dmamode(ap, qc->dev); + + /* Cases the state machine will not complete correctly without help */ + if ((tf->flags & ATA_TFLAG_LBA48) || tf->protocol == ATA_PROT_ATAPI_DMA) + { + if (tf->flags & ATA_TFLAG_LBA48) + len = qc->nsect * 512; + else + len = qc->nbytes; + + if (tf->flags & ATA_TFLAG_WRITE) + len |= 0x06000000; + else + len |= 0x05000000; + + outl(len, atapi_reg); + } + + /* Activate DMA */ + ata_bmdma_start(qc); +} + +/** + * pdc2026x_bmdma_end - DMA engine stop + * @qc: ATA command + * + * After a DMA completes we need to put the clock back to 33MHz for + * PIO timings. + */ + +static void pdc2026x_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_taskfile *tf = &qc->tf; + + int sel66 = ap->port_no ? 0x08: 0x02; + /* The clock bits are in the same register for both channels */ + unsigned long master = ap->host->ports[0]->ioaddr.bmdma_addr; + unsigned long clock = master + 0x11; + unsigned long atapi_reg = master + 0x20 + (4 * ap->port_no); + + /* Cases the state machine will not complete correctly */ + if (tf->protocol == ATA_PROT_ATAPI_DMA || ( tf->flags & ATA_TFLAG_LBA48)) { + outl(0, atapi_reg); + outb(inb(clock) & ~sel66, clock); + } + /* Check we keep host level locking here */ + /* Flip back to 33Mhz for PIO */ + if (adev->dma_mode >= XFER_UDMA_2) + outb(inb(clock) & ~sel66, clock); + + ata_bmdma_stop(qc); +} + +/** + * pdc2026x_dev_config - device setup hook + * @ap: ATA port + * @adev: newly found device + * + * Perform chip specific early setup. We need to lock the transfer + * sizes to 8bit to avoid making the state engine on the 2026x cards + * barf. + */ + +static void pdc2026x_dev_config(struct ata_port *ap, struct ata_device *adev) +{ + adev->max_sectors = 256; +} + +static struct scsi_host_template pdc_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations pdc2024x_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = pdc_set_piomode, + .set_dmamode = pdc_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2024x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations pdc2026x_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = pdc_set_piomode, + .set_dmamode = pdc_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .dev_config = pdc2026x_dev_config, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = pdc2026x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = pdc2026x_bmdma_start, + .bmdma_stop = pdc2026x_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int pdc_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info[3] = { + { + .sht = &pdc_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA2, + .port_ops = &pdc2024x_port_ops + }, + { + .sht = &pdc_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA4, + .port_ops = &pdc2026x_port_ops + }, + { + .sht = &pdc_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA5, + .port_ops = &pdc2026x_port_ops + } + + }; + static struct ata_port_info *port_info[2]; + + port_info[0] = port_info[1] = &info[id->driver_data]; + + if (dev->device == PCI_DEVICE_ID_PROMISE_20265) { + struct pci_dev *bridge = dev->bus->self; + /* Don't grab anything behind a Promise I2O RAID */ + if (bridge && bridge->vendor == PCI_VENDOR_ID_INTEL) { + if( bridge->device == PCI_DEVICE_ID_INTEL_I960) + return -ENODEV; + if( bridge->device == PCI_DEVICE_ID_INTEL_I960RM) + return -ENODEV; + } + } + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id pdc[] = { + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2}, + { 0, }, +}; + +static struct pci_driver pdc_pci_driver = { + .name = DRV_NAME, + .id_table = pdc, + .probe = pdc_init_one, + .remove = ata_pci_remove_one +}; + +static int __init pdc_init(void) +{ + return pci_register_driver(&pdc_pci_driver); +} + + +static void __exit pdc_exit(void) +{ + pci_unregister_driver(&pdc_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pdc); +MODULE_VERSION(DRV_VERSION); + +module_init(pdc_init); +module_exit(pdc_exit); diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c new file mode 100644 index 00000000000..7977f471d5e --- /dev/null +++ b/drivers/ata/pata_qdi.c @@ -0,0 +1,403 @@ +/* + * pata_qdi.c - QDI VLB ATA controllers + * (C) 2006 Red Hat <alan@redhat.com> + * + * This driver mostly exists as a proof of concept for non PCI devices under + * libata. While the QDI6580 was 'neat' in 1993 it is no longer terribly + * useful. + * + * Tuning code written from the documentation at + * http://www.ryston.cz/petr/vlb/qd6500.html + * http://www.ryston.cz/petr/vlb/qd6580.html + * + * Probe code based on drivers/ide/legacy/qd65xx.c + * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by + * Samuel Thibault <samuel.thibault@fnac.net> + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/platform_device.h> + +#define DRV_NAME "pata_qdi" +#define DRV_VERSION "0.2.4" + +#define NR_HOST 4 /* Two 6580s */ + +struct qdi_data { + unsigned long timing; + u8 clock[2]; + u8 last; + int fast; + struct platform_device *platform_dev; + +}; + +static struct ata_host *qdi_host[NR_HOST]; +static struct qdi_data qdi_data[NR_HOST]; +static int nr_qdi_host; + +#ifdef MODULE +static int probe_qdi = 1; +#else +static int probe_qdi; +#endif + +static void qdi6500_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct ata_timing t; + struct qdi_data *qdi = ap->host->private_data; + int active, recovery; + u8 timing; + + /* Get the timing data in cycles */ + ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000); + + if (qdi->fast) { + active = 8 - FIT(t.active, 1, 8); + recovery = 18 - FIT(t.recover, 3, 18); + } else { + active = 9 - FIT(t.active, 2, 9); + recovery = 15 - FIT(t.recover, 0, 15); + } + timing = (recovery << 4) | active | 0x08; + + qdi->clock[adev->devno] = timing; + + outb(timing, qdi->timing); +} + +static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct ata_timing t; + struct qdi_data *qdi = ap->host->private_data; + int active, recovery; + u8 timing; + + /* Get the timing data in cycles */ + ata_timing_compute(adev, adev->pio_mode, &t, 30303, 1000); + + if (qdi->fast) { + active = 8 - FIT(t.active, 1, 8); + recovery = 18 - FIT(t.recover, 3, 18); + } else { + active = 9 - FIT(t.active, 2, 9); + recovery = 15 - FIT(t.recover, 0, 15); + } + timing = (recovery << 4) | active | 0x08; + + qdi->clock[adev->devno] = timing; + + outb(timing, qdi->timing); + + /* Clear the FIFO */ + if (adev->class != ATA_DEV_ATA) + outb(0x5F, (qdi->timing & 0xFFF0) + 3); +} + +/** + * qdi_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings. + */ + +static unsigned int qdi_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct qdi_data *qdi = ap->host->private_data; + + if (qdi->clock[adev->devno] != qdi->last) { + if (adev->pio_mode) { + qdi->last = qdi->clock[adev->devno]; + outb(qdi->clock[adev->devno], qdi->timing); + } + } + return ata_qc_issue_prot(qc); +} + +static void qdi_data_xfer(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data) +{ + struct ata_port *ap = adev->ap; + int slop = buflen & 3; + + if (ata_id_has_dword_io(adev->id)) { + if (write_data) + outsl(ap->ioaddr.data_addr, buf, buflen >> 2); + else + insl(ap->ioaddr.data_addr, buf, buflen >> 2); + + if (unlikely(slop)) { + u32 pad; + if (write_data) { + memcpy(&pad, buf + buflen - slop, slop); + outl(le32_to_cpu(pad), ap->ioaddr.data_addr); + } else { + pad = cpu_to_le16(inl(ap->ioaddr.data_addr)); + memcpy(buf + buflen - slop, &pad, slop); + } + } + } else + ata_pio_data_xfer(adev, buf, buflen, write_data); +} + +static struct scsi_host_template qdi_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations qdi6500_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = qdi6500_set_piomode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = qdi_qc_issue_prot, + + .data_xfer = qdi_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations qdi6580_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = qdi6580_set_piomode, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .qc_prep = ata_qc_prep, + .qc_issue = qdi_qc_issue_prot, + + .data_xfer = qdi_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * qdi_init_one - attach a qdi interface + * @type: Type to display + * @io: I/O port start + * @irq: interrupt line + * @fast: True if on a > 33Mhz VLB + * + * Register an ISA bus IDE interface. Such interfaces are PIO and we + * assume do not support IRQ sharing. + */ + +static __init int qdi_init_one(unsigned long port, int type, unsigned long io, int irq, int fast) +{ + struct ata_probe_ent ae; + struct platform_device *pdev; + int ret; + + unsigned long ctrl = io + 0x206; + + /* + * Fill in a probe structure first of all + */ + + pdev = platform_device_register_simple(DRV_NAME, nr_qdi_host, NULL, 0); + if (pdev == NULL) + return -ENOMEM; + + memset(&ae, 0, sizeof(struct ata_probe_ent)); + INIT_LIST_HEAD(&ae.node); + ae.dev = &pdev->dev; + + if (type == 6580) { + ae.port_ops = &qdi6580_port_ops; + ae.pio_mask = 0x1F; + } else { + ae.port_ops = &qdi6500_port_ops; + ae.pio_mask = 0x07; /* Actually PIO3 !IORDY is possible */ + } + + ae.sht = &qdi_sht; + ae.n_ports = 1; + ae.irq = irq; + ae.irq_flags = 0; + ae.port_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST; + ae.port[0].cmd_addr = io; + ae.port[0].altstatus_addr = ctrl; + ae.port[0].ctl_addr = ctrl; + ata_std_ports(&ae.port[0]); + + /* + * Hook in a private data structure per channel + */ + ae.private_data = &qdi_data[nr_qdi_host]; + + qdi_data[nr_qdi_host].timing = port; + qdi_data[nr_qdi_host].fast = fast; + qdi_data[nr_qdi_host].platform_dev = pdev; + + printk(KERN_INFO DRV_NAME": qd%d at 0x%lx.\n", type, io); + ret = ata_device_add(&ae); + if (ret == 0) { + platform_device_unregister(pdev); + return -ENODEV; + } + + qdi_host[nr_qdi_host++] = dev_get_drvdata(&pdev->dev); + return 0; +} + +/** + * qdi_init - attach qdi interfaces + * + * Attach qdi IDE interfaces by scanning the ports it may occupy. + */ + +static __init int qdi_init(void) +{ + unsigned long flags; + static const unsigned long qd_port[2] = { 0x30, 0xB0 }; + static const unsigned long ide_port[2] = { 0x170, 0x1F0 }; + static const int ide_irq[2] = { 14, 15 }; + + int ct = 0; + int i; + + if (probe_qdi == 0) + return -ENODEV; + + /* + * Check each possible QD65xx base address + */ + + for (i = 0; i < 2; i++) { + unsigned long port = qd_port[i]; + u8 r, res; + + + if (request_region(port, 2, "pata_qdi")) { + /* Check for a card */ + local_irq_save(flags); + r = inb_p(port); + outb_p(0x19, port); + res = inb_p(port); + outb_p(r, port); + local_irq_restore(flags); + + /* Fail */ + if (res == 0x19) + { + release_region(port, 2); + continue; + } + + /* Passes the presence test */ + r = inb_p(port + 1); /* Check port agrees with port set */ + if ((r & 2) >> 1 != i) { + release_region(port, 2); + continue; + } + + /* Check card type */ + if ((r & 0xF0) == 0xC0) { + /* QD6500: single channel */ + if (r & 8) { + /* Disabled ? */ + release_region(port, 2); + continue; + } + ct += qdi_init_one(port, 6500, ide_port[r & 0x01], ide_irq[r & 0x01], r & 0x04); + } + if (((r & 0xF0) == 0xA0) || (r & 0xF0) == 0x50) { + /* QD6580: dual channel */ + if (!request_region(port + 2 , 2, "pata_qdi")) + { + release_region(port, 2); + continue; + } + res = inb(port + 3); + if (res & 1) { + /* Single channel mode */ + ct += qdi_init_one(port, 6580, ide_port[r & 0x01], ide_irq[r & 0x01], r & 0x04); + } else { + /* Dual channel mode */ + ct += qdi_init_one(port, 6580, 0x1F0, 14, r & 0x04); + ct += qdi_init_one(port + 2, 6580, 0x170, 15, r & 0x04); + } + } + } + } + if (ct != 0) + return 0; + return -ENODEV; +} + +static __exit void qdi_exit(void) +{ + int i; + + for (i = 0; i < nr_qdi_host; i++) { + ata_host_remove(qdi_host[i]); + /* Free the control resource. The 6580 dual channel has the resources + * claimed as a pair of 2 byte resources so we need no special cases... + */ + release_region(qdi_data[i].timing, 2); + platform_device_unregister(qdi_data[i].platform_dev); + } +} + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for qdi ATA"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); + +module_init(qdi_init); +module_exit(qdi_exit); + +module_param(probe_qdi, int, 0); + diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c new file mode 100644 index 00000000000..c20bcf43ed6 --- /dev/null +++ b/drivers/ata/pata_radisys.c @@ -0,0 +1,333 @@ +/* + * pata_radisys.c - Intel PATA/SATA controllers + * + * (C) 2006 Red Hat <alan@redhat.com> + * + * Some parts based on ata_piix.c by Jeff Garzik and others. + * + * A PIIX relative, this device has a single ATA channel and no + * slave timings, SITRE or PPE. In that sense it is a close relative + * of the original PIIX. It does however support UDMA 33/66 per channel + * although no other modes/timings. Also lacking is 32bit I/O on the ATA + * port. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_radisys" +#define DRV_VERSION "0.4.1" + +/** + * radisys_probe_init - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int radisys_pre_reset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + + +/** + * radisys_pata_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * @classes: + * + * LOCKING: + * None (inherited from caller). + */ + +static void radisys_pata_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, radisys_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * radisys_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u16 idetm_data; + int control = 0; + + /* + * See Intel Document 298600-004 for the timing programing rules + * for PIIX/ICH. Note that the early PIIX does not have the slave + * timing port at 0x44. The Radisys is a relative of the PIIX + * but not the same so be careful. + */ + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, /* Check me */ + { 0, 0 }, + { 1, 1 }, + { 2, 2 }, + { 3, 3 }, }; + + if (pio > 0) + control |= 1; /* TIME1 enable */ + if (ata_pio_need_iordy(adev)) + control |= 2; /* IE IORDY */ + + pci_read_config_word(dev, 0x40, &idetm_data); + + /* Enable IE and TIME as appropriate. Clear the other + drive timing bits */ + idetm_data &= 0xCCCC; + idetm_data |= (control << (4 * adev->devno)); + idetm_data |= (timings[pio][0] << 12) | + (timings[pio][1] << 8); + pci_write_config_word(dev, 0x40, idetm_data); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * radisys_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * @isich: True if the device is an ICH and has IOCFG registers + * + * Set MWDMA mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u16 idetm_data; + u8 udma_enable; + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 1 }, + { 2, 2 }, + { 3, 3 }, }; + + /* + * MWDMA is driven by the PIO timings. We must also enable + * IORDY unconditionally. + */ + + pci_read_config_word(dev, 0x40, &idetm_data); + pci_read_config_byte(dev, 0x48, &udma_enable); + + if (adev->dma_mode < XFER_UDMA_0) { + unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; + const unsigned int needed_pio[3] = { + XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 + }; + int pio = needed_pio[mwdma] - XFER_PIO_0; + int control = 3; /* IORDY|TIME0 */ + + /* If the drive MWDMA is faster than it can do PIO then + we must force PIO0 for PIO cycles. */ + + if (adev->pio_mode < needed_pio[mwdma]) + control = 1; + + /* Mask out the relevant control and timing bits we will load. Also + clear the other drive TIME register as a precaution */ + + idetm_data &= 0xCCCC; + idetm_data |= control << (4 * adev->devno); + idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); + + udma_enable &= ~(1 << adev->devno); + } else { + u8 udma_mode; + + /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */ + + pci_read_config_byte(dev, 0x4A, &udma_mode); + + if (adev->xfer_mode == XFER_UDMA_2) + udma_mode &= ~ (1 << adev->devno); + else /* UDMA 4 */ + udma_mode |= (1 << adev->devno); + + pci_write_config_byte(dev, 0x4A, udma_mode); + + udma_enable |= (1 << adev->devno); + } + pci_write_config_word(dev, 0x40, idetm_data); + pci_write_config_byte(dev, 0x48, udma_enable); + + /* Track which port is configured */ + ap->private_data = adev; +} + +/** + * radisys_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * neccessary. Our logic also clears TIME0/TIME1 for the other device so + * that, even if we get this wrong, cycles to the other device will + * be made PIO0. + */ + +static unsigned int radisys_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + + if (adev != ap->private_data) { + /* UDMA timing is not shared */ + if (adev->dma_mode < XFER_UDMA_0) { + if (adev->dma_mode) + radisys_set_dmamode(ap, adev); + else if (adev->pio_mode) + radisys_set_piomode(ap, adev); + } + } + return ata_qc_issue_prot(qc); +} + + +static struct scsi_host_template radisys_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations radisys_pata_ops = { + .port_disable = ata_port_disable, + .set_piomode = radisys_set_piomode, + .set_dmamode = radisys_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = radisys_pata_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = radisys_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + + +/** + * radisys_init_one - Register PIIX ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in radisys_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. We probe for combined mode (sigh), + * and then hand over control to libata, for it to do the rest. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + static struct ata_port_info info = { + .sht = &radisys_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma1-2 */ + .udma_mask = 0x14, /* UDMA33/66 only */ + .port_ops = &radisys_pata_ops, + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id radisys_pci_tbl[] = { + { 0x1331, 0x8201, PCI_ANY_ID, PCI_ANY_ID, }, + { } /* terminate list */ +}; + +static struct pci_driver radisys_pci_driver = { + .name = DRV_NAME, + .id_table = radisys_pci_tbl, + .probe = radisys_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init radisys_init(void) +{ + return pci_register_driver(&radisys_pci_driver); +} + +static void __exit radisys_exit(void) +{ + pci_unregister_driver(&radisys_pci_driver); +} + + +module_init(radisys_init); +module_exit(radisys_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, radisys_pci_tbl); +MODULE_VERSION(DRV_VERSION); + diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c new file mode 100644 index 00000000000..eccc6fd4503 --- /dev/null +++ b/drivers/ata/pata_rz1000.c @@ -0,0 +1,205 @@ +/* + * RZ1000/1001 driver based upon + * + * linux/drivers/ide/pci/rz1000.c Version 0.06 January 12, 2003 + * Copyright (C) 1995-1998 Linus Torvalds & author (see below) + * Principal Author: mlord@pobox.com (Mark Lord) + * + * See linux/MAINTAINERS for address of current maintainer. + * + * This file provides support for disabling the buggy read-ahead + * mode of the RZ1000 IDE chipset, commonly used on Intel motherboards. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_rz1000" +#define DRV_VERSION "0.2.2" + + +/** + * rz1000_prereset - probe begin + * @ap: ATA port + * + * Set up cable type and use generics + */ + +static int rz1000_prereset(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * rz1000_error_handler - probe reset + * @ap: ATA port + * + * Perform the ATA standard reset sequence + */ + +static void rz1000_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, rz1000_prereset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * rz1000_set_mode - mode setting function + * @ap: ATA interface + * + * Use a non standard set_mode function. We don't want to be tuned. We + * would prefer to be BIOS generic but for the fact our hardware is + * whacked out. + */ + +static void rz1000_set_mode(struct ata_port *ap) +{ + int i; + + for (i = 0; i < ATA_MAX_DEVICES; i++) { + struct ata_device *dev = &ap->device[i]; + if (ata_dev_enabled(dev)) { + /* We don't really care */ + dev->pio_mode = XFER_PIO_0; + dev->xfer_mode = XFER_PIO_0; + dev->xfer_shift = ATA_SHIFT_PIO; + dev->flags |= ATA_DFLAG_PIO; + } + } +} + + +static struct scsi_host_template rz1000_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations rz1000_port_ops = { + .set_mode = rz1000_set_mode, + + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = rz1000_error_handler, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = rz1000_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * rz1000_init_one - Register RZ1000 ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in rz1000_pci_tbl matching with @pdev + * + * Configure an RZ1000 interface. This doesn't require much special + * handling except that we *MUST* kill the chipset readahead or the + * user may experience data corruption. + */ + +static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_port_info *port_info[2]; + u16 reg; + static struct ata_port_info info = { + .sht = &rz1000_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .port_ops = &rz1000_port_ops + }; + + if (!printed_version++) + printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n"); + + /* Be exceptionally paranoid as we must be sure to apply the fix */ + if (pci_read_config_word(pdev, 0x40, ®) != 0) + goto fail; + reg &= 0xDFFF; + if (pci_write_config_word(pdev, 0x40, reg) != 0) + goto fail; + printk(KERN_INFO DRV_NAME ": disabled chipset readahead.\n"); + + port_info[0] = &info; + port_info[1] = &info; + return ata_pci_init_one(pdev, port_info, 2); +fail: + printk(KERN_ERR DRV_NAME ": failed to disable read-ahead on chipset..\n"); + /* Not safe to use so skip */ + return -ENODEV; +} + +static struct pci_device_id pata_rz1000[] = { + { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1000), }, + { PCI_DEVICE(PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_RZ1001), }, + { 0, }, +}; + +static struct pci_driver rz1000_pci_driver = { + .name = DRV_NAME, + .id_table = pata_rz1000, + .probe = rz1000_init_one, + .remove = ata_pci_remove_one +}; + + +static int __init rz1000_init(void) +{ + return pci_register_driver(&rz1000_pci_driver); +} + +static void __exit rz1000_exit(void) +{ + pci_unregister_driver(&rz1000_pci_driver); +} + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for RZ1000 PCI ATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pata_rz1000); +MODULE_VERSION(DRV_VERSION); + +module_init(rz1000_init); +module_exit(rz1000_exit); + diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c new file mode 100644 index 00000000000..107e6cd3dc0 --- /dev/null +++ b/drivers/ata/pata_sc1200.c @@ -0,0 +1,287 @@ +/* + * New ATA layer SC1200 driver Alan Cox <alan@redhat.com> + * + * TODO: Mode selection filtering + * TODO: Can't enable second channel until ATA core has serialize + * TODO: Needs custom DMA cleanup code + * + * Based very heavily on + * + * linux/drivers/ide/pci/sc1200.c Version 0.91 28-Jan-2003 + * + * Copyright (C) 2000-2002 Mark Lord <mlord@pobox.com> + * May be copied or modified under the terms of the GNU General Public License + * + * Development of this chipset driver was funded + * by the nice folks at National Semiconductor. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "sc1200" +#define DRV_VERSION "0.2.3" + +#define SC1200_REV_A 0x00 +#define SC1200_REV_B1 0x01 +#define SC1200_REV_B3 0x02 +#define SC1200_REV_C1 0x03 +#define SC1200_REV_D1 0x04 + +/** + * sc1200_clock - PCI clock + * + * Return the PCI bus clocking for the SC1200 chipset configuration + * in use. We return 0 for 33MHz 1 for 48MHz and 2 for 66Mhz + */ + +static int sc1200_clock(void) +{ + /* Magic registers that give us the chipset data */ + u8 chip_id = inb(0x903C); + u8 silicon_rev = inb(0x903D); + u16 pci_clock; + + if (chip_id == 0x04 && silicon_rev < SC1200_REV_B1) + return 0; /* 33 MHz mode */ + + /* Clock generator configuration 0x901E its 8/9 are the PCI clocking + 0/3 is 33Mhz 1 is 48 2 is 66 */ + + pci_clock = inw(0x901E); + pci_clock >>= 8; + pci_clock &= 0x03; + if (pci_clock == 3) + pci_clock = 0; + return pci_clock; +} + +/** + * sc1200_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Set our PIO requirements. This is fairly simple on the SC1200 + */ + +static void sc1200_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const u32 pio_timings[4][5] = { + {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, // format0 33Mhz + {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}, // format1, 33Mhz + {0xfaa3f4f3, 0xc23232b2, 0x513101c1, 0x31213121, 0x10211021}, // format1, 48Mhz + {0xfff4fff4, 0xf35353d3, 0x814102f1, 0x42314231, 0x11311131} // format1, 66Mhz + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 format; + unsigned int reg = 0x40 + 0x10 * ap->port_no; + int mode = adev->pio_mode - XFER_PIO_0; + + pci_read_config_dword(pdev, reg + 4, &format); + format >>= 31; + format += sc1200_clock(); + pci_write_config_dword(pdev, reg + 8 * adev->devno, + pio_timings[format][mode]); +} + +/** + * sc1200_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * We cannot mix MWDMA and UDMA without reloading timings each switch + * master to slave. + */ + +static void sc1200_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const u32 udma_timing[3][3] = { + { 0x00921250, 0x00911140, 0x00911030 }, + { 0x00932470, 0x00922260, 0x00922140 }, + { 0x009436A1, 0x00933481, 0x00923261 } + }; + + static const u32 mwdma_timing[3][3] = { + { 0x00077771, 0x00012121, 0x00002020 }, + { 0x000BBBB2, 0x00024241, 0x00013131 }, + { 0x000FFFF3, 0x00035352, 0x00015151 } + }; + + int clock = sc1200_clock(); + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned int reg = 0x40 + 0x10 * ap->port_no; + int mode = adev->dma_mode; + u32 format; + + if (mode >= XFER_UDMA_0) + format = udma_timing[clock][mode - XFER_UDMA_0]; + else + format = mwdma_timing[clock][mode - XFER_MW_DMA_0]; + + if (adev->devno == 0) { + u32 timings; + + pci_read_config_dword(pdev, reg + 4, &timings); + timings &= 0x80000000UL; + timings |= format; + pci_write_config_dword(pdev, reg + 4, timings); + } else + pci_write_config_dword(pdev, reg + 12, format); +} + +/** + * sc1200_qc_issue_prot - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * neccessary. Specifically we have a problem that there is only + * one MWDMA/UDMA bit. + */ + +static unsigned int sc1200_qc_issue_prot(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_device *prev = ap->private_data; + + /* See if the DMA settings could be wrong */ + if (adev->dma_mode != 0 && adev != prev && prev != NULL) { + /* Maybe, but do the channels match MWDMA/UDMA ? */ + if ((adev->dma_mode >= XFER_UDMA_0 && prev->dma_mode < XFER_UDMA_0) || + (adev->dma_mode < XFER_UDMA_0 && prev->dma_mode >= XFER_UDMA_0)) + /* Switch the mode bits */ + sc1200_set_dmamode(ap, adev); + } + + return ata_qc_issue_prot(qc); +} + +static struct scsi_host_template sc1200_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations sc1200_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = sc1200_set_piomode, + .set_dmamode = sc1200_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = ata_bmdma_error_handler, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = sc1200_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * sc1200_init_one - Initialise an SC1200 + * @dev: PCI device + * @id: Entry in match table + * + * Just throw the needed data at the libata helper and it does all + * our work. + */ + +static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &sc1200_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, + .port_ops = &sc1200_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + + /* Can't enable port 2 yet, see top comments */ + return ata_pci_init_one(dev, port_info, 1); +} + +static struct pci_device_id sc1200[] = { + { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_IDE), }, + { 0, }, +}; + +static struct pci_driver sc1200_pci_driver = { + .name = DRV_NAME, + .id_table = sc1200, + .probe = sc1200_init_one, + .remove = ata_pci_remove_one +}; + +static int __init sc1200_init(void) +{ + return pci_register_driver(&sc1200_pci_driver); +} + + +static void __exit sc1200_exit(void) +{ + pci_unregister_driver(&sc1200_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox, Mark Lord"); +MODULE_DESCRIPTION("low-level driver for the NS/AMD SC1200"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sc1200); +MODULE_VERSION(DRV_VERSION); + +module_init(sc1200_init); +module_exit(sc1200_exit); diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c new file mode 100644 index 00000000000..a5c8d7e121d --- /dev/null +++ b/drivers/ata/pata_serverworks.c @@ -0,0 +1,591 @@ +/* + * ata-serverworks.c - Serverworks PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based upon + * + * serverworks.c + * + * Copyright (C) 1998-2000 Michel Aubry + * Copyright (C) 1998-2000 Andrzej Krzysztofowicz + * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> + * Portions copyright (c) 2001 Sun Microsystems + * + * + * RCC/ServerWorks IDE driver for Linux + * + * OSB4: `Open South Bridge' IDE Interface (fn 1) + * supports UDMA mode 2 (33 MB/s) + * + * CSB5: `Champion South Bridge' IDE Interface (fn 1) + * all revisions support UDMA mode 4 (66 MB/s) + * revision A2.0 and up support UDMA mode 5 (100 MB/s) + * + * *** The CSB5 does not provide ANY register *** + * *** to detect 80-conductor cable presence. *** + * + * CSB6: `Champion South Bridge' IDE Interface (optional: third channel) + * + * Documentation: + * Available under NDA only. Errata info very hard to get. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_serverworks" +#define DRV_VERSION "0.3.7" + +#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */ +#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */ + +/* Seagate Barracuda ATA IV Family drives in UDMA mode 5 + * can overrun their FIFOs when used with the CSB5 */ + +static const char *csb_bad_ata100[] = { + "ST320011A", + "ST340016A", + "ST360021A", + "ST380021A", + NULL +}; + +/** + * dell_cable - Dell serverworks cable detection + * @ap: ATA port to do cable detect + * + * Dell hide the 40/80 pin select for their interfaces in the top two + * bits of the subsystem ID. + */ + +static int dell_cable(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (pdev->subsystem_device & (1 << (ap->port_no + 14))) + return ATA_CBL_PATA80; + return ATA_CBL_PATA40; +} + +/** + * sun_cable - Sun Cobalt 'Alpine' cable detection + * @ap: ATA port to do cable select + * + * Cobalt CSB5 IDE hides the 40/80pin in the top two bits of the + * subsystem ID the same as dell. We could use one function but we may + * need to extend the Dell one in future + */ + +static int sun_cable(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (pdev->subsystem_device & (1 << (ap->port_no + 14))) + return ATA_CBL_PATA80; + return ATA_CBL_PATA40; +} + +/** + * osb4_cable - OSB4 cable detect + * @ap: ATA port to check + * + * The OSB4 isn't UDMA66 capable so this is easy + */ + +static int osb4_cable(struct ata_port *ap) { + return ATA_CBL_PATA40; +} + +/** + * csb4_cable - CSB5/6 cable detect + * @ap: ATA port to check + * + * Serverworks default arrangement is to use the drive side detection + * only. + */ + +static int csb_cable(struct ata_port *ap) { + return ATA_CBL_PATA80; +} + +struct sv_cable_table { + int device; + int subvendor; + int (*cable_detect)(struct ata_port *ap); +}; + +/* + * Note that we don't copy the old serverworks code because the old + * code contains obvious mistakes + */ + +static struct sv_cable_table cable_detect[] = { + { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_DELL, dell_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_VENDOR_ID_DELL, dell_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_SUN, sun_cable }, + { PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, osb4_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, csb_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, csb_cable }, + { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, csb_cable }, + { PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, csb_cable }, + { } +}; + +/** + * serverworks_pre_reset - cable detection + * @ap: ATA port + * + * Perform cable detection according to the device and subvendor + * identifications + */ + +static int serverworks_pre_reset(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct sv_cable_table *cb = cable_detect; + + while(cb->device) { + if (cb->device == pdev->device && + (cb->subvendor == pdev->subsystem_vendor || + cb->subvendor == PCI_ANY_ID)) { + ap->cbl = cb->cable_detect(ap); + return ata_std_prereset(ap); + } + cb++; + } + + BUG(); + return -1; /* kill compiler warning */ +} + +static void serverworks_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, serverworks_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * serverworks_is_csb - Check for CSB or OSB + * @pdev: PCI device to check + * + * Returns true if the device being checked is known to be a CSB + * series device. + */ + +static u8 serverworks_is_csb(struct pci_dev *pdev) +{ + switch (pdev->device) { + case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE: + case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE: + case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2: + case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE: + return 1; + default: + break; + } + return 0; +} + +/** + * serverworks_osb4_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Filter the offered modes for the device to apply controller + * specific rules. OSB4 requires no UDMA for disks due to a FIFO + * bug we hit. + */ + +static unsigned long serverworks_osb4_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + if (adev->class == ATA_DEV_ATA) + mask &= ~ATA_MASK_UDMA; + return ata_pci_default_filter(ap, adev, mask); +} + + +/** + * serverworks_csb_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Check the blacklist and disable UDMA5 if matched + */ + +static unsigned long serverworks_csb_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + const char *p; + char model_num[40]; + int len, i; + + /* Disk, UDMA */ + if (adev->class != ATA_DEV_ATA) + return ata_pci_default_filter(ap, adev, mask); + + /* Actually do need to check */ + ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num)); + /* Precuationary - why not do this in the libata core ?? */ + + len = strlen(model_num); + while ((len > 0) && (model_num[len - 1] == ' ')) { + len--; + model_num[len] = 0; + } + + for(i = 0; (p = csb_bad_ata100[i]) != NULL; i++) { + if (!strncmp(p, model_num, len)) + mask &= ~(0x1F << ATA_SHIFT_UDMA); + } + return ata_pci_default_filter(ap, adev, mask); +} + + +/** + * serverworks_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the OSB4/CSB5 timing registers for PIO. The PIO register + * load is done as a simple lookup. + */ +static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 }; + int offset = 1 + (2 * ap->port_no) - adev->devno; + int devbits = (2 * ap->port_no + adev->devno) * 4; + u16 csb5_pio; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int pio = adev->pio_mode - XFER_PIO_0; + + pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]); + + /* The OSB4 just requires the timing but the CSB series want the + mode number as well */ + if (serverworks_is_csb(pdev)) { + pci_read_config_word(pdev, 0x4A, &csb5_pio); + csb5_pio &= ~(0x0F << devbits); + pci_write_config_byte(pdev, 0x4A, csb5_pio | (pio << devbits)); + } +} + +/** + * serverworks_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5 + * chipset. The MWDMA mode values are pulled from a lookup table + * while the chipset uses mode number for UDMA. + */ + +static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const u8 dma_mode[] = { 0x77, 0x21, 0x20 }; + int offset = 1 + 2 * ap->port_no - adev->devno; + int devbits = (2 * ap->port_no + adev->devno); + u8 ultra; + u8 ultra_cfg; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x54, &ultra_cfg); + + if (adev->dma_mode >= XFER_UDMA_0) { + pci_write_config_byte(pdev, 0x44 + offset, 0x20); + + pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra); + ultra &= ~(0x0F << (ap->port_no * 4)); + ultra |= (adev->dma_mode - XFER_UDMA_0) + << (ap->port_no * 4); + pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra); + + ultra_cfg |= (1 << devbits); + } else { + pci_write_config_byte(pdev, 0x44 + offset, + dma_mode[adev->dma_mode - XFER_MW_DMA_0]); + ultra_cfg &= ~(1 << devbits); + } + pci_write_config_byte(pdev, 0x54, ultra_cfg); +} + +static struct scsi_host_template serverworks_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations serverworks_osb4_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = serverworks_set_piomode, + .set_dmamode = serverworks_set_dmamode, + .mode_filter = serverworks_osb4_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = serverworks_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations serverworks_csb_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = serverworks_set_piomode, + .set_dmamode = serverworks_set_dmamode, + .mode_filter = serverworks_csb_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = serverworks_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int serverworks_fixup_osb4(struct pci_dev *pdev) +{ + u32 reg; + struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, + PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL); + if (isa_dev) { + pci_read_config_dword(isa_dev, 0x64, ®); + reg &= ~0x00002000; /* disable 600ns interrupt mask */ + if (!(reg & 0x00004000)) + printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n"); + reg |= 0x00004000; /* enable UDMA/33 support */ + pci_write_config_dword(isa_dev, 0x64, reg); + pci_dev_put(isa_dev); + return 0; + } + printk(KERN_WARNING "ata_serverworks: Unable to find bridge.\n"); + return -ENODEV; +} + +static int serverworks_fixup_csb(struct pci_dev *pdev) +{ + u8 rev; + u8 btr; + + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); + + /* Third Channel Test */ + if (!(PCI_FUNC(pdev->devfn) & 1)) { + struct pci_dev * findev = NULL; + u32 reg4c = 0; + findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, + PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL); + if (findev) { + pci_read_config_dword(findev, 0x4C, ®4c); + reg4c &= ~0x000007FF; + reg4c |= 0x00000040; + reg4c |= 0x00000020; + pci_write_config_dword(findev, 0x4C, reg4c); + pci_dev_put(findev); + } + } else { + struct pci_dev * findev = NULL; + u8 reg41 = 0; + + findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, + PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL); + if (findev) { + pci_read_config_byte(findev, 0x41, ®41); + reg41 &= ~0x40; + pci_write_config_byte(findev, 0x41, reg41); + pci_dev_put(findev); + } + } + /* setup the UDMA Control register + * + * 1. clear bit 6 to enable DMA + * 2. enable DMA modes with bits 0-1 + * 00 : legacy + * 01 : udma2 + * 10 : udma2/udma4 + * 11 : udma2/udma4/udma5 + */ + pci_read_config_byte(pdev, 0x5A, &btr); + btr &= ~0x40; + if (!(PCI_FUNC(pdev->devfn) & 1)) + btr |= 0x2; + else + btr |= (rev >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2; + pci_write_config_byte(pdev, 0x5A, btr); + + return btr; +} + +static void serverworks_fixup_ht1000(struct pci_dev *pdev) +{ + u8 btr; + /* Setup HT1000 SouthBridge Controller - Single Channel Only */ + pci_read_config_byte(pdev, 0x5A, &btr); + btr &= ~0x40; + btr |= 0x3; + pci_write_config_byte(pdev, 0x5A, btr); +} + + +static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + int ports = 2; + static struct ata_port_info info[4] = { + { /* OSB4 */ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, + .port_ops = &serverworks_osb4_port_ops + }, { /* OSB4 no UDMA */ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x00, + .port_ops = &serverworks_osb4_port_ops + }, { /* CSB5 */ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, + .port_ops = &serverworks_csb_port_ops + }, { /* CSB5 - later revisions*/ + .sht = &serverworks_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &serverworks_csb_port_ops + } + }; + static struct ata_port_info *port_info[2]; + struct ata_port_info *devinfo = &info[id->driver_data]; + + /* Force master latency timer to 64 PCI clocks */ + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40); + + /* OSB4 : South Bridge and IDE */ + if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) { + /* Select non UDMA capable OSB4 if we can't do fixups */ + if ( serverworks_fixup_osb4(pdev) < 0) + devinfo = &info[1]; + } + /* setup CSB5/CSB6 : South Bridge and IDE option RAID */ + else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) || + (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) || + (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) { + + /* If the returned btr is the newer revision then + select the right info block */ + if (serverworks_fixup_csb(pdev) == 3) + devinfo = &info[3]; + + /* Is this the 3rd channel CSB6 IDE ? */ + if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2) + ports = 1; + } + /* setup HT1000E */ + else if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) + serverworks_fixup_ht1000(pdev); + + if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) + ata_pci_clear_simplex(pdev); + + port_info[0] = port_info[1] = devinfo; + return ata_pci_init_one(pdev, port_info, ports); +} + +static struct pci_device_id serverworks[] = { + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2}, + { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2}, + { 0, }, +}; + +static struct pci_driver serverworks_pci_driver = { + .name = DRV_NAME, + .id_table = serverworks, + .probe = serverworks_init_one, + .remove = ata_pci_remove_one +}; + +static int __init serverworks_init(void) +{ + return pci_register_driver(&serverworks_pci_driver); +} + + +static void __exit serverworks_exit(void) +{ + pci_unregister_driver(&serverworks_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, serverworks); +MODULE_VERSION(DRV_VERSION); + +module_init(serverworks_init); +module_exit(serverworks_exit); diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c new file mode 100644 index 00000000000..c8b2e26db70 --- /dev/null +++ b/drivers/ata/pata_sil680.c @@ -0,0 +1,381 @@ +/* + * pata_sil680.c - SIL680 PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based upon + * + * linux/drivers/ide/pci/siimage.c Version 1.07 Nov 30, 2003 + * + * Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org> + * Copyright (C) 2003 Red Hat <alan@redhat.com> + * + * May be copied or modified under the terms of the GNU General Public License + * + * Documentation publically available. + * + * If you have strange problems with nVidia chipset systems please + * see the SI support documentation and update your system BIOS + * if neccessary + * + * TODO + * If we know all our devices are LBA28 (or LBA28 sized) we could use + * the command fifo mode. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_sil680" +#define DRV_VERSION "0.3.2" + +/** + * sil680_selreg - return register base + * @hwif: interface + * @r: config offset + * + * Turn a config register offset into the right address in either + * PCI space or MMIO space to access the control register in question + * Thankfully this is a configuration operation so isnt performance + * criticial. + */ + +static unsigned long sil680_selreg(struct ata_port *ap, int r) +{ + unsigned long base = 0xA0 + r; + base += (ap->port_no << 4); + return base; +} + +/** + * sil680_seldev - return register base + * @hwif: interface + * @r: config offset + * + * Turn a config register offset into the right address in either + * PCI space or MMIO space to access the control register in question + * including accounting for the unit shift. + */ + +static unsigned long sil680_seldev(struct ata_port *ap, struct ata_device *adev, int r) +{ + unsigned long base = 0xA0 + r; + base += (ap->port_no << 4); + base |= adev->devno ? 2 : 0; + return base; +} + + +/** + * sil680_cable_detect - cable detection + * @ap: ATA port + * + * Perform cable detection. The SIL680 stores this in PCI config + * space for us. + */ + +static int sil680_cable_detect(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned long addr = sil680_selreg(ap, 0); + u8 ata66; + pci_read_config_byte(pdev, addr, &ata66); + if (ata66 & 1) + return ATA_CBL_PATA80; + else + return ATA_CBL_PATA40; +} + +static int sil680_pre_reset(struct ata_port *ap) +{ + ap->cbl = sil680_cable_detect(ap); + return ata_std_prereset(ap); +} + +/** + * sil680_bus_reset - reset the SIL680 bus + * @ap: ATA port to reset + * + * Perform the SIL680 housekeeping when doing an ATA bus reset + */ + +static int sil680_bus_reset(struct ata_port *ap,unsigned int *classes) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned long addr = sil680_selreg(ap, 0); + u8 reset; + + pci_read_config_byte(pdev, addr, &reset); + pci_write_config_byte(pdev, addr, reset | 0x03); + udelay(25); + pci_write_config_byte(pdev, addr, reset); + return ata_std_softreset(ap, classes); +} + +static void sil680_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sil680_pre_reset, sil680_bus_reset, NULL, ata_std_postreset); +} + +/** + * sil680_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the SIL680 registers for PIO mode. Note that the task speed + * registers are shared between the devices so we must pick the lowest + * mode for command work. + */ + +static void sil680_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static u16 speed_p[5] = { 0x328A, 0x2283, 0x1104, 0x10C3, 0x10C1 }; + static u16 speed_t[5] = { 0x328A, 0x1281, 0x1281, 0x10C3, 0x10C1 }; + + unsigned long tfaddr = sil680_selreg(ap, 0x02); + unsigned long addr = sil680_seldev(ap, adev, 0x04); + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int pio = adev->pio_mode - XFER_PIO_0; + int lowest_pio = pio; + u16 reg; + + struct ata_device *pair = ata_dev_pair(adev); + + if (pair != NULL && adev->pio_mode > pair->pio_mode) + lowest_pio = pair->pio_mode - XFER_PIO_0; + + pci_write_config_word(pdev, addr, speed_p[pio]); + pci_write_config_word(pdev, tfaddr, speed_t[lowest_pio]); + + pci_read_config_word(pdev, tfaddr-2, ®); + reg &= ~0x0200; /* Clear IORDY */ + if (ata_pio_need_iordy(adev)) + reg |= 0x0200; /* Enable IORDY */ + pci_write_config_word(pdev, tfaddr-2, reg); +} + +/** + * sil680_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Program the MWDMA/UDMA modes for the sil680 k + * chipset. The MWDMA mode values are pulled from a lookup table + * while the chipset uses mode number for UDMA. + */ + +static void sil680_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static u8 ultra_table[2][7] = { + { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01, 0xFF }, /* 100MHz */ + { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 }, /* 133Mhz */ + }; + static u16 dma_table[3] = { 0x2208, 0x10C2, 0x10C1 }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned long ma = sil680_seldev(ap, adev, 0x08); + unsigned long ua = sil680_seldev(ap, adev, 0x0C); + unsigned long addr_mask = 0x80 + 4 * ap->port_no; + int port_shift = adev->devno * 4; + u8 scsc, mode; + u16 multi, ultra; + + pci_read_config_byte(pdev, 0x8A, &scsc); + pci_read_config_byte(pdev, addr_mask, &mode); + pci_read_config_word(pdev, ma, &multi); + pci_read_config_word(pdev, ua, &ultra); + + /* Mask timing bits */ + ultra &= ~0x3F; + mode &= ~(0x03 << port_shift); + + /* Extract scsc */ + scsc = (scsc & 0x30) ? 1: 0; + + if (adev->dma_mode >= XFER_UDMA_0) { + multi = 0x10C1; + ultra |= ultra_table[scsc][adev->dma_mode - XFER_UDMA_0]; + mode |= (0x03 << port_shift); + } else { + multi = dma_table[adev->dma_mode - XFER_MW_DMA_0]; + mode |= (0x02 << port_shift); + } + pci_write_config_byte(pdev, addr_mask, mode); + pci_write_config_word(pdev, ma, multi); + pci_write_config_word(pdev, ua, ultra); +} + +static struct scsi_host_template sil680_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations sil680_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = sil680_set_piomode, + .set_dmamode = sil680_set_dmamode, + .mode_filter = ata_pci_default_filter, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sil680_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &sil680_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &sil680_port_ops + }; + static struct ata_port_info info_slow = { + .sht = &sil680_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &sil680_port_ops + }; + static struct ata_port_info *port_info[2] = {&info, &info}; + static int printed_version; + u32 class_rev = 0; + u8 tmpbyte = 0; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xff; + /* FIXME: double check */ + pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, (class_rev) ? 1 : 255); + + pci_write_config_byte(pdev, 0x80, 0x00); + pci_write_config_byte(pdev, 0x84, 0x00); + + pci_read_config_byte(pdev, 0x8A, &tmpbyte); + + printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n", + tmpbyte & 1, tmpbyte & 0x30); + + switch(tmpbyte & 0x30) { + case 0x00: + /* 133 clock attempt to force it on */ + pci_write_config_byte(pdev, 0x8A, tmpbyte|0x10); + break; + case 0x30: + /* if clocking is disabled */ + /* 133 clock attempt to force it on */ + pci_write_config_byte(pdev, 0x8A, tmpbyte & ~0x20); + break; + case 0x10: + /* 133 already */ + break; + case 0x20: + /* BIOS set PCI x2 clocking */ + break; + } + + pci_read_config_byte(pdev, 0x8A, &tmpbyte); + printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n", + tmpbyte & 1, tmpbyte & 0x30); + if ((tmpbyte & 0x30) == 0) + port_info[0] = port_info[1] = &info_slow; + + pci_write_config_byte(pdev, 0xA1, 0x72); + pci_write_config_word(pdev, 0xA2, 0x328A); + pci_write_config_dword(pdev, 0xA4, 0x62DD62DD); + pci_write_config_dword(pdev, 0xA8, 0x43924392); + pci_write_config_dword(pdev, 0xAC, 0x40094009); + pci_write_config_byte(pdev, 0xB1, 0x72); + pci_write_config_word(pdev, 0xB2, 0x328A); + pci_write_config_dword(pdev, 0xB4, 0x62DD62DD); + pci_write_config_dword(pdev, 0xB8, 0x43924392); + pci_write_config_dword(pdev, 0xBC, 0x40094009); + + switch(tmpbyte & 0x30) { + case 0x00: printk(KERN_INFO "sil680: 100MHz clock.\n");break; + case 0x10: printk(KERN_INFO "sil680: 133MHz clock.\n");break; + case 0x20: printk(KERN_INFO "sil680: Using PCI clock.\n");break; + /* This last case is _NOT_ ok */ + case 0x30: printk(KERN_ERR "sil680: Clock disabled ?\n"); + return -EIO; + } + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id sil680[] = { + { PCI_DEVICE(PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_680), }, + { 0, }, +}; + +static struct pci_driver sil680_pci_driver = { + .name = DRV_NAME, + .id_table = sil680, + .probe = sil680_init_one, + .remove = ata_pci_remove_one +}; + +static int __init sil680_init(void) +{ + return pci_register_driver(&sil680_pci_driver); +} + + +static void __exit sil680_exit(void) +{ + pci_unregister_driver(&sil680_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for SI680 PATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sil680); +MODULE_VERSION(DRV_VERSION); + +module_init(sil680_init); +module_exit(sil680_exit); diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c new file mode 100644 index 00000000000..17791e2785f --- /dev/null +++ b/drivers/ata/pata_sis.c @@ -0,0 +1,1022 @@ +/* + * pata_sis.c - SiS ATA driver + * + * (C) 2005 Red Hat <alan@redhat.com> + * + * Based upon linux/drivers/ide/pci/sis5513.c + * Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org> + * Copyright (C) 2002 Lionel Bouton <Lionel.Bouton@inet6.fr>, Maintainer + * Copyright (C) 2003 Vojtech Pavlik <vojtech@suse.cz> + * SiS Taiwan : for direct support and hardware. + * Daniela Engert : for initial ATA100 advices and numerous others. + * John Fremlin, Manfred Spraul, Dave Morgan, Peter Kjellerstedt : + * for checking code correctness, providing patches. + * Original tests and design on the SiS620 chipset. + * ATA100 tests and design on the SiS735 chipset. + * ATA16/33 support from specs + * ATA133 support for SiS961/962 by L.C. Chang <lcchang@sis.com.tw> + * + * + * TODO + * Check MWDMA on drives that don't support MWDMA speed pio cycles ? + * More Testing + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_sis" +#define DRV_VERSION "0.4.4" + +struct sis_chipset { + u16 device; /* PCI host ID */ + struct ata_port_info *info; /* Info block */ + /* Probably add family, cable detect type etc here to clean + up code later */ +}; + +/** + * sis_port_base - return PCI configuration base for dev + * @adev: device + * + * Returns the base of the PCI configuration registers for this port + * number. + */ + +static int sis_port_base(struct ata_device *adev) +{ + return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno); +} + +/** + * sis_133_pre_reset - check for 40/80 pin + * @ap: Port + * + * Perform cable detection for the later UDMA133 capable + * SiS chipset. + */ + +static int sis_133_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits sis_enable_bits[] = { + { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 tmp; + + if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) + return -ENOENT; + + /* The top bit of this register is the cable detect bit */ + pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp); + if (tmp & 0x8000) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + return ata_std_prereset(ap); +} + +/** + * sis_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sis_133_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + + +/** + * sis_66_pre_reset - check for 40/80 pin + * @ap: Port + * + * Perform cable detection on the UDMA66, UDMA100 and early UDMA133 + * SiS IDE controllers. + */ + +static int sis_66_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits sis_enable_bits[] = { + { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 tmp; + + if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) { + ata_port_disable(ap); + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + /* Older chips keep cable detect in bits 4/5 of reg 0x48 */ + pci_read_config_byte(pdev, 0x48, &tmp); + tmp >>= ap->port_no; + if (tmp & 0x10) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + return ata_std_prereset(ap); +} + +/** + * sis_66_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * @classes: + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_66_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sis_66_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * sis_old_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int sis_old_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits sis_enable_bits[] = { + { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */ + { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */ + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) { + ata_port_disable(ap); + printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id); + return 0; + } + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + + +/** + * sis_old_error_handler - Probe specified port on PATA host controller + * @ap: Port to probe + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_old_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sis_old_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * sis_set_fifo - Set RWP fifo bits for this device + * @ap: Port + * @adev: Device + * + * SIS chipsets implement prefetch/postwrite bits for each device + * on both channels. This functionality is not ATAPI compatible and + * must be configured according to the class of device present + */ + +static void sis_set_fifo(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 fifoctrl; + u8 mask = 0x11; + + mask <<= (2 * ap->port_no); + mask <<= adev->devno; + + /* This holds various bits including the FIFO control */ + pci_read_config_byte(pdev, 0x4B, &fifoctrl); + fifoctrl &= ~mask; + + /* Enable for ATA (disk) only */ + if (adev->class == ATA_DEV_ATA) + fifoctrl |= mask; + pci_write_config_byte(pdev, 0x4B, fifoctrl); +} + +/** + * sis_old_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring for. + * + * Set PIO mode for device, in host controller PCI config space. This + * function handles PIO set up for all chips that are pre ATA100 and + * also early ATA100 devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = sis_port_base(adev); + u8 t1, t2; + int speed = adev->pio_mode - XFER_PIO_0; + + const u8 active[] = { 0x00, 0x07, 0x04, 0x03, 0x01 }; + const u8 recovery[] = { 0x00, 0x06, 0x04, 0x03, 0x03 }; + + sis_set_fifo(ap, adev); + + pci_read_config_byte(pdev, port, &t1); + pci_read_config_byte(pdev, port + 1, &t2); + + t1 &= ~0x0F; /* Clear active/recovery timings */ + t2 &= ~0x07; + + t1 |= active[speed]; + t2 |= recovery[speed]; + + pci_write_config_byte(pdev, port, t1); + pci_write_config_byte(pdev, port + 1, t2); +} + +/** + * sis_100_set_pioode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring for. + * + * Set PIO mode for device, in host controller PCI config space. This + * function handles PIO set up for ATA100 devices and early ATA133. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = sis_port_base(adev); + int speed = adev->pio_mode - XFER_PIO_0; + + const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 }; + + sis_set_fifo(ap, adev); + + pci_write_config_byte(pdev, port, actrec[speed]); +} + +/** + * sis_133_set_pioode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device we are configuring for. + * + * Set PIO mode for device, in host controller PCI config space. This + * function handles PIO set up for the later ATA133 devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int port = 0x40; + u32 t1; + u32 reg54; + int speed = adev->pio_mode - XFER_PIO_0; + + const u32 timing133[] = { + 0x28269000, /* Recovery << 24 | Act << 16 | Ini << 12 */ + 0x0C266000, + 0x04263000, + 0x0C0A3000, + 0x05093000 + }; + const u32 timing100[] = { + 0x1E1C6000, /* Recovery << 24 | Act << 16 | Ini << 12 */ + 0x091C4000, + 0x031C2000, + 0x09072000, + 0x04062000 + }; + + sis_set_fifo(ap, adev); + + /* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */ + pci_read_config_dword(pdev, 0x54, ®54); + if (reg54 & 0x40000000) + port = 0x70; + port += 8 * ap->port_no + 4 * adev->devno; + + pci_read_config_dword(pdev, port, &t1); + t1 &= 0xC0C00FFF; /* Mask out timing */ + + if (t1 & 0x08) /* 100 or 133 ? */ + t1 |= timing133[speed]; + else + t1 |= timing100[speed]; + pci_write_config_byte(pdev, port, t1); +} + +/** + * sis_old_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles pre UDMA and UDMA33 devices. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 }; + const u16 udma_bits[] = { 0xE000, 0xC000, 0xA000 }; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* bits 3-0 hold recovery timing bits 8-10 active timing and + the higer bits are dependant on the device */ + timing &= ~ 0x870F; + timing |= mwdma_bits[speed]; + pci_write_config_word(pdev, drive_pci, timing); + } else { + /* Bit 15 is UDMA on/off, bit 13-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x6000; + timing |= udma_bits[speed]; + } +} + +/** + * sis_66_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles UDMA66 and early UDMA100 devices. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 }; + const u16 udma_bits[] = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000}; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* bits 3-0 hold recovery timing bits 8-10 active timing and + the higer bits are dependant on the device, bit 15 udma */ + timing &= ~ 0x870F; + timing |= mwdma_bits[speed]; + } else { + /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x6000; + timing |= udma_bits[speed]; + } + pci_write_config_word(pdev, drive_pci, timing); +} + +/** + * sis_100_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles UDMA66 and early UDMA100 devices. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 udma_bits[] = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100}; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */ + } else { + /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x0F00; + timing |= udma_bits[speed]; + } + pci_write_config_word(pdev, drive_pci, timing); +} + +/** + * sis_133_early_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles early SiS 961 bridges. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int drive_pci = sis_port_base(adev); + u16 timing; + + const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100}; + + pci_read_config_word(pdev, drive_pci, &timing); + + if (adev->dma_mode < XFER_UDMA_0) { + /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */ + } else { + /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */ + speed = adev->dma_mode - XFER_UDMA_0; + timing &= ~0x0F00; + timing |= udma_bits[speed]; + } + pci_write_config_word(pdev, drive_pci, timing); +} + +/** + * sis_133_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * Handles early SiS 961 bridges. Supports MWDMA as well unlike + * the old ide/pci driver. + * + * LOCKING: + * None (inherited from caller). + */ + +static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int speed = adev->dma_mode - XFER_MW_DMA_0; + int port = 0x40; + u32 t1; + u32 reg54; + + /* bits 4- cycle time 8 - cvs time */ + const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 }; + const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 }; + + /* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */ + pci_read_config_dword(pdev, 0x54, ®54); + if (reg54 & 0x40000000) + port = 0x70; + port += (8 * ap->port_no) + (4 * adev->devno); + + pci_read_config_dword(pdev, port, &t1); + + if (adev->dma_mode < XFER_UDMA_0) { + t1 &= ~0x00000004; + /* FIXME: need data sheet to add MWDMA here. Also lacking on + ide/pci driver */ + } else { + speed = adev->dma_mode - XFER_UDMA_0; + /* if & 8 no UDMA133 - need info for ... */ + t1 &= ~0x00000FF0; + t1 |= 0x00000004; + if (t1 & 0x08) + t1 |= timing_u133[speed]; + else + t1 |= timing_u100[speed]; + } + pci_write_config_dword(pdev, port, t1); +} + +static struct scsi_host_template sis_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations sis_133_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_133_set_piomode, + .set_dmamode = sis_133_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_133_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_133_early_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_100_set_piomode, + .set_dmamode = sis_133_early_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_66_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_100_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_100_set_piomode, + .set_dmamode = sis_100_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_66_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_66_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_old_set_piomode, + .set_dmamode = sis_66_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_66_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations sis_old_ops = { + .port_disable = ata_port_disable, + .set_piomode = sis_old_set_piomode, + .set_dmamode = sis_old_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = sis_old_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static struct ata_port_info sis_info = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, + .udma_mask = 0, + .port_ops = &sis_old_ops, +}; +static struct ata_port_info sis_info33 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA2, /* UDMA 33 */ + .port_ops = &sis_old_ops, +}; +static struct ata_port_info sis_info66 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA4, /* UDMA 66 */ + .port_ops = &sis_66_ops, +}; +static struct ata_port_info sis_info100 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA5, + .port_ops = &sis_100_ops, +}; +static struct ata_port_info sis_info100_early = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .udma_mask = ATA_UDMA5, + .pio_mask = 0x1f, /* pio0-4 */ + .port_ops = &sis_66_ops, +}; +static struct ata_port_info sis_info133 = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA6, + .port_ops = &sis_133_ops, +}; +static struct ata_port_info sis_info133_early = { + .sht = &sis_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = ATA_UDMA6, + .port_ops = &sis_133_early_ops, +}; + + +static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis) +{ + u16 regw; + u8 reg; + + if (sis->info == &sis_info133) { + pci_read_config_word(pdev, 0x50, ®w); + if (regw & 0x08) + pci_write_config_word(pdev, 0x50, regw & ~0x08); + pci_read_config_word(pdev, 0x52, ®w); + if (regw & 0x08) + pci_write_config_word(pdev, 0x52, regw & ~0x08); + return; + } + + if (sis->info == &sis_info133_early || sis->info == &sis_info100) { + /* Fix up latency */ + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80); + /* Set compatibility bit */ + pci_read_config_byte(pdev, 0x49, ®); + if (!(reg & 0x01)) + pci_write_config_byte(pdev, 0x49, reg | 0x01); + return; + } + + if (sis->info == &sis_info66 || sis->info == &sis_info100_early) { + /* Fix up latency */ + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80); + /* Set compatibility bit */ + pci_read_config_byte(pdev, 0x52, ®); + if (!(reg & 0x04)) + pci_write_config_byte(pdev, 0x52, reg | 0x04); + return; + } + + if (sis->info == &sis_info33) { + pci_read_config_byte(pdev, PCI_CLASS_PROG, ®); + if (( reg & 0x0F ) != 0x00) + pci_write_config_byte(pdev, PCI_CLASS_PROG, reg & 0xF0); + /* Fall through to ATA16 fixup below */ + } + + if (sis->info == &sis_info || sis->info == &sis_info33) { + /* force per drive recovery and active timings + needed on ATA_33 and below chips */ + pci_read_config_byte(pdev, 0x52, ®); + if (!(reg & 0x08)) + pci_write_config_byte(pdev, 0x52, reg|0x08); + return; + } + + BUG(); +} + +/** + * sis_init_one - Register SiS ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in sis_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. We probe for combined mode (sigh), + * and then hand over control to libata, for it to do the rest. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + static struct ata_port_info *port_info[2]; + struct ata_port_info *port; + struct pci_dev *host = NULL; + struct sis_chipset *chipset = NULL; + + static struct sis_chipset sis_chipsets[] = { + + { 0x0968, &sis_info133 }, + { 0x0966, &sis_info133 }, + { 0x0965, &sis_info133 }, + { 0x0745, &sis_info100 }, + { 0x0735, &sis_info100 }, + { 0x0733, &sis_info100 }, + { 0x0635, &sis_info100 }, + { 0x0633, &sis_info100 }, + + { 0x0730, &sis_info100_early }, /* 100 with ATA 66 layout */ + { 0x0550, &sis_info100_early }, /* 100 with ATA 66 layout */ + + { 0x0640, &sis_info66 }, + { 0x0630, &sis_info66 }, + { 0x0620, &sis_info66 }, + { 0x0540, &sis_info66 }, + { 0x0530, &sis_info66 }, + + { 0x5600, &sis_info33 }, + { 0x5598, &sis_info33 }, + { 0x5597, &sis_info33 }, + { 0x5591, &sis_info33 }, + { 0x5582, &sis_info33 }, + { 0x5581, &sis_info33 }, + + { 0x5596, &sis_info }, + { 0x5571, &sis_info }, + { 0x5517, &sis_info }, + { 0x5511, &sis_info }, + + {0} + }; + static struct sis_chipset sis133_early = { + 0x0, &sis_info133_early + }; + static struct sis_chipset sis133 = { + 0x0, &sis_info133 + }; + static struct sis_chipset sis100_early = { + 0x0, &sis_info100_early + }; + static struct sis_chipset sis100 = { + 0x0, &sis_info100 + }; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + /* We have to find the bridge first */ + + for (chipset = &sis_chipsets[0]; chipset->device; chipset++) { + host = pci_get_device(PCI_VENDOR_ID_SI, chipset->device, NULL); + if (host != NULL) { + if (chipset->device == 0x630) { /* SIS630 */ + u8 host_rev; + pci_read_config_byte(host, PCI_REVISION_ID, &host_rev); + if (host_rev >= 0x30) /* 630 ET */ + chipset = &sis100_early; + } + break; + } + } + + /* Look for concealed bridges */ + if (host == NULL) { + /* Second check */ + u32 idemisc; + u16 trueid; + + /* Disable ID masking and register remapping then + see what the real ID is */ + + pci_read_config_dword(pdev, 0x54, &idemisc); + pci_write_config_dword(pdev, 0x54, idemisc & 0x7fffffff); + pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid); + pci_write_config_dword(pdev, 0x54, idemisc); + + switch(trueid) { + case 0x5518: /* SIS 962/963 */ + chipset = &sis133; + if ((idemisc & 0x40000000) == 0) { + pci_write_config_dword(pdev, 0x54, idemisc | 0x40000000); + printk(KERN_INFO "SIS5513: Switching to 5513 register mapping\n"); + } + break; + case 0x0180: /* SIS 965/965L */ + chipset = &sis133; + break; + case 0x1180: /* SIS 966/966L */ + chipset = &sis133; + break; + } + } + + /* Further check */ + if (chipset == NULL) { + struct pci_dev *lpc_bridge; + u16 trueid; + u8 prefctl; + u8 idecfg; + u8 sbrev; + + /* Try the second unmasking technique */ + pci_read_config_byte(pdev, 0x4a, &idecfg); + pci_write_config_byte(pdev, 0x4a, idecfg | 0x10); + pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid); + pci_write_config_byte(pdev, 0x4a, idecfg); + + switch(trueid) { + case 0x5517: + lpc_bridge = pci_get_slot(pdev->bus, 0x10); /* Bus 0 Dev 2 Fn 0 */ + if (lpc_bridge == NULL) + break; + pci_read_config_byte(lpc_bridge, PCI_REVISION_ID, &sbrev); + pci_read_config_byte(pdev, 0x49, &prefctl); + pci_dev_put(lpc_bridge); + + if (sbrev == 0x10 && (prefctl & 0x80)) { + chipset = &sis133_early; + break; + } + chipset = &sis100; + break; + } + } + pci_dev_put(host); + + /* No chipset info, no support */ + if (chipset == NULL) + return -ENODEV; + + port = chipset->info; + port->private_data = chipset; + + sis_fixup(pdev, chipset); + + port_info[0] = port_info[1] = port; + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id sis_pci_tbl[] = { + { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5513), }, /* SiS 5513 */ + { PCI_DEVICE(PCI_VENDOR_ID_SI, 0x5518), }, /* SiS 5518 */ + { } +}; + +static struct pci_driver sis_pci_driver = { + .name = DRV_NAME, + .id_table = sis_pci_tbl, + .probe = sis_init_one, + .remove = ata_pci_remove_one, +}; + +static int __init sis_init(void) +{ + return pci_register_driver(&sis_pci_driver); +} + +static void __exit sis_exit(void) +{ + pci_unregister_driver(&sis_pci_driver); +} + + +module_init(sis_init); +module_exit(sis_exit); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for SiS ATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sis_pci_tbl); +MODULE_VERSION(DRV_VERSION); + diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c new file mode 100644 index 00000000000..5b762acc568 --- /dev/null +++ b/drivers/ata/pata_sl82c105.c @@ -0,0 +1,385 @@ +/* + * pata_sl82c105.c - SL82C105 PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Based in part on linux/drivers/ide/pci/sl82c105.c + * SL82C105/Winbond 553 IDE driver + * + * and in part on the documentation and errata sheet + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_sl82c105" +#define DRV_VERSION "0.2.3" + +enum { + /* + * SL82C105 PCI config register 0x40 bits. + */ + CTRL_IDE_IRQB = (1 << 30), + CTRL_IDE_IRQA = (1 << 28), + CTRL_LEGIRQ = (1 << 11), + CTRL_P1F16 = (1 << 5), + CTRL_P1EN = (1 << 4), + CTRL_P0F16 = (1 << 1), + CTRL_P0EN = (1 << 0) +}; + +/** + * sl82c105_pre_reset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int sl82c105_pre_reset(struct ata_port *ap) +{ + static const struct pci_bits sl82c105_enable_bits[] = { + { 0x40, 1, 0x01, 0x01 }, + { 0x40, 1, 0x10, 0x10 } + }; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no])) + return -ENOENT; + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + + +static void sl82c105_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, sl82c105_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + + +/** + * sl82c105_configure_piomode - set chip PIO timing + * @ap: ATA interface + * @adev: ATA device + * @pio: PIO mode + * + * Called to do the PIO mode setup. Our timing registers are shared + * so a configure_dmamode call will undo any work we do here and vice + * versa + */ + +static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static u16 pio_timing[5] = { + 0x50D, 0x407, 0x304, 0x242, 0x240 + }; + u16 dummy; + int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno); + + pci_write_config_word(pdev, timing, pio_timing[pio]); + /* Can we lose this oddity of the old driver */ + pci_read_config_word(pdev, timing, &dummy); +} + +/** + * sl82c105_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the PIO mode setup. Our timing registers are shared + * but we want to set the PIO timing by default. + */ + +static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); +} + +/** + * sl82c105_configure_dmamode - set DMA mode in chip + * @ap: ATA interface + * @adev: ATA device + * + * Load DMA cycle times into the chip ready for a DMA transfer + * to occur. + */ + +static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static u16 dma_timing[3] = { + 0x707, 0x201, 0x200 + }; + u16 dummy; + int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno); + int dma = adev->dma_mode - XFER_MW_DMA_0; + + pci_write_config_word(pdev, timing, dma_timing[dma]); + /* Can we lose this oddity of the old driver */ + pci_read_config_word(pdev, timing, &dummy); +} + +/** + * sl82c105_set_dmamode - set initial DMA mode data + * @ap: ATA interface + * @adev: ATA device + * + * Called to do the DMA mode setup. This replaces the PIO timings + * for the device in question. Set appropriate PIO timings not DMA + * timings at this point. + */ + +static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + switch(adev->dma_mode) { + case XFER_MW_DMA_0: + sl82c105_configure_piomode(ap, adev, 1); + break; + case XFER_MW_DMA_1: + sl82c105_configure_piomode(ap, adev, 3); + break; + case XFER_MW_DMA_2: + sl82c105_configure_piomode(ap, adev, 3); + break; + default: + BUG(); + } +} + +/** + * sl82c105_reset_engine - Reset the DMA engine + * @ap: ATA interface + * + * The sl82c105 has some serious problems with the DMA engine + * when transfers don't run as expected or ATAPI is used. The + * recommended fix is to reset the engine each use using a chip + * test register. + */ + +static void sl82c105_reset_engine(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 val; + + pci_read_config_word(pdev, 0x7E, &val); + pci_write_config_word(pdev, 0x7E, val | 4); + pci_write_config_word(pdev, 0x7E, val & ~4); +} + +/** + * sl82c105_bmdma_start - DMA engine begin + * @qc: ATA command + * + * Reset the DMA engine each use as recommended by the errata + * document. + * + * FIXME: if we switch clock at BMDMA start/end we might get better + * PIO performance on DMA capable devices. + */ + +static void sl82c105_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + sl82c105_reset_engine(ap); + + /* Set the clocks for DMA */ + sl82c105_configure_dmamode(ap, qc->dev); + /* Activate DMA */ + ata_bmdma_start(qc); +} + +/** + * sl82c105_bmdma_end - DMA engine stop + * @qc: ATA command + * + * Reset the DMA engine each use as recommended by the errata + * document. + * + * This function is also called to turn off DMA when a timeout occurs + * during DMA operation. In both cases we need to reset the engine, + * so no actual eng_timeout handler is required. + * + * We assume bmdma_stop is always called if bmdma_start as called. If + * not then we may need to wrap qc_issue. + */ + +static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + ata_bmdma_stop(qc); + sl82c105_reset_engine(ap); + + /* This will redo the initial setup of the DMA device to matching + PIO timings */ + sl82c105_set_dmamode(ap, qc->dev); +} + +static struct scsi_host_template sl82c105_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations sl82c105_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = sl82c105_set_piomode, + .set_dmamode = sl82c105_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .error_handler = sl82c105_error_handler, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = sl82c105_bmdma_start, + .bmdma_stop = sl82c105_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * sl82c105_bridge_revision - find bridge version + * @pdev: PCI device for the ATA function + * + * Locates the PCI bridge associated with the ATA function and + * providing it is a Winbond 553 reports the revision. If it cannot + * find a revision or the right device it returns -1 + */ + +static int sl82c105_bridge_revision(struct pci_dev *pdev) +{ + struct pci_dev *bridge; + u8 rev; + + /* + * The bridge should be part of the same device, but function 0. + */ + bridge = pci_get_slot(pdev->bus, + PCI_DEVFN(PCI_SLOT(pdev->devfn), 0)); + if (!bridge) + return -1; + + /* + * Make sure it is a Winbond 553 and is an ISA bridge. + */ + if (bridge->vendor != PCI_VENDOR_ID_WINBOND || + bridge->device != PCI_DEVICE_ID_WINBOND_83C553 || + bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) { + pci_dev_put(bridge); + return -1; + } + /* + * We need to find function 0's revision, not function 1 + */ + pci_read_config_byte(bridge, PCI_REVISION_ID, &rev); + + pci_dev_put(bridge); + return rev; +} + + +static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info_dma = { + .sht = &sl82c105_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &sl82c105_port_ops + }; + static struct ata_port_info info_early = { + .sht = &sl82c105_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .port_ops = &sl82c105_port_ops + }; + static struct ata_port_info *port_info[2] = { &info_early, &info_early }; + u32 val; + int rev; + + rev = sl82c105_bridge_revision(dev); + + if (rev == -1) + dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n"); + else if (rev <= 5) + dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Early bridge revision, no DMA available.\n"); + else { + port_info[0] = &info_dma; + port_info[1] = &info_dma; + } + + pci_read_config_dword(dev, 0x40, &val); + val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16; + pci_write_config_dword(dev, 0x40, val); + + + return ata_pci_init_one(dev, port_info, 1); /* For now */ +} + +static struct pci_device_id sl82c105[] = { + { PCI_DEVICE(PCI_VENDOR_ID_WINBOND, PCI_DEVICE_ID_WINBOND_82C105), }, + { 0, }, +}; + +static struct pci_driver sl82c105_pci_driver = { + .name = DRV_NAME, + .id_table = sl82c105, + .probe = sl82c105_init_one, + .remove = ata_pci_remove_one +}; + +static int __init sl82c105_init(void) +{ + return pci_register_driver(&sl82c105_pci_driver); +} + + +static void __exit sl82c105_exit(void) +{ + pci_unregister_driver(&sl82c105_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Sl82c105"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sl82c105); +MODULE_VERSION(DRV_VERSION); + +module_init(sl82c105_init); +module_exit(sl82c105_exit); diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c new file mode 100644 index 00000000000..a954ed93a40 --- /dev/null +++ b/drivers/ata/pata_triflex.c @@ -0,0 +1,282 @@ +/* + * pata_triflex.c - Compaq PATA for new ATA layer + * (C) 2005 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * based upon + * + * triflex.c + * + * IDE Chipset driver for the Compaq TriFlex IDE controller. + * + * Known to work with the Compaq Workstation 5x00 series. + * + * Copyright (C) 2002 Hewlett-Packard Development Group, L.P. + * Author: Torben Mathiasen <torben.mathiasen@hp.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Loosely based on the piix & svwks drivers. + * + * Documentation: + * Not publically available. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_triflex" +#define DRV_VERSION "0.2.5" + +/** + * triflex_prereset - probe begin + * @ap: ATA port + * + * Set up cable type and use generic probe init + */ + +static int triflex_prereset(struct ata_port *ap) +{ + static const struct pci_bits triflex_enable_bits[] = { + { 0x80, 1, 0x01, 0x01 }, + { 0x80, 1, 0x02, 0x02 } + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!pci_test_config_bits(pdev, &triflex_enable_bits[ap->port_no])) + return -ENOENT; + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + + + +static void triflex_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, triflex_prereset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * triflex_load_timing - timing configuration + * @ap: ATA interface + * @adev: Device on the bus + * @speed: speed to configure + * + * The Triflex has one set of timings per device per channel. This + * means we must do some switching. As the PIO and DMA timings don't + * match we have to do some reloading unlike PIIX devices where tuning + * tricks can avoid it. + */ + +static void triflex_load_timing(struct ata_port *ap, struct ata_device *adev, int speed) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 timing = 0; + u32 triflex_timing, old_triflex_timing; + int channel_offset = ap->port_no ? 0x74: 0x70; + unsigned int is_slave = (adev->devno != 0); + + + pci_read_config_dword(pdev, channel_offset, &old_triflex_timing); + triflex_timing = old_triflex_timing; + + switch(speed) + { + case XFER_MW_DMA_2: + timing = 0x0103;break; + case XFER_MW_DMA_1: + timing = 0x0203;break; + case XFER_MW_DMA_0: + timing = 0x0808;break; + case XFER_SW_DMA_2: + case XFER_SW_DMA_1: + case XFER_SW_DMA_0: + timing = 0x0F0F;break; + case XFER_PIO_4: + timing = 0x0202;break; + case XFER_PIO_3: + timing = 0x0204;break; + case XFER_PIO_2: + timing = 0x0404;break; + case XFER_PIO_1: + timing = 0x0508;break; + case XFER_PIO_0: + timing = 0x0808;break; + default: + BUG(); + } + triflex_timing &= ~ (0xFFFF << (16 * is_slave)); + triflex_timing |= (timing << (16 * is_slave)); + + if (triflex_timing != old_triflex_timing) + pci_write_config_dword(pdev, channel_offset, triflex_timing); +} + +/** + * triflex_set_piomode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * + * Use the timing loader to set up the PIO mode. We have to do this + * because DMA start/stop will only be called once DMA occurs. If there + * has been no DMA then the PIO timings are still needed. + */ +static void triflex_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + triflex_load_timing(ap, adev, adev->pio_mode); +} + +/** + * triflex_dma_start - DMA start callback + * @qc: Command in progress + * + * Usually drivers set the DMA timing at the point the set_dmamode call + * is made. Triflex however requires we load new timings on the + * transition or keep matching PIO/DMA pairs (ie MWDMA2/PIO4 etc). + * We load the DMA timings just before starting DMA and then restore + * the PIO timing when the DMA is finished. + */ + +static void triflex_bmdma_start(struct ata_queued_cmd *qc) +{ + triflex_load_timing(qc->ap, qc->dev, qc->dev->dma_mode); + ata_bmdma_start(qc); +} + +/** + * triflex_dma_stop - DMA stop callback + * @ap: ATA interface + * @adev: ATA device + * + * We loaded new timings in dma_start, as a result we need to restore + * the PIO timings in dma_stop so that the next command issue gets the + * right clock values. + */ + +static void triflex_bmdma_stop(struct ata_queued_cmd *qc) +{ + ata_bmdma_stop(qc); + triflex_load_timing(qc->ap, qc->dev, qc->dev->pio_mode); +} + +static struct scsi_host_template triflex_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations triflex_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = triflex_set_piomode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = triflex_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = triflex_bmdma_start, + .bmdma_stop = triflex_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &triflex_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &triflex_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + static int printed_version; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); + + return ata_pci_init_one(dev, port_info, 2); +} + +static const struct pci_device_id triflex[] = { + { PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, + { 0, }, +}; + +static struct pci_driver triflex_pci_driver = { + .name = DRV_NAME, + .id_table = triflex, + .probe = triflex_init_one, + .remove = ata_pci_remove_one +}; + +static int __init triflex_init(void) +{ + return pci_register_driver(&triflex_pci_driver); +} + + +static void __exit triflex_exit(void) +{ + pci_unregister_driver(&triflex_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for Compaq Triflex"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, triflex); +MODULE_VERSION(DRV_VERSION); + +module_init(triflex_init); +module_exit(triflex_exit); diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c new file mode 100644 index 00000000000..7b5dd2343b9 --- /dev/null +++ b/drivers/ata/pata_via.c @@ -0,0 +1,565 @@ +/* + * pata_via.c - VIA PATA for new ATA layer + * (C) 2005-2006 Red Hat Inc + * Alan Cox <alan@redhat.com> + * + * Documentation + * Most chipset documentation available under NDA only + * + * VIA version guide + * VIA VT82C561 - early design, uses ata_generic currently + * VIA VT82C576 - MWDMA, 33Mhz + * VIA VT82C586 - MWDMA, 33Mhz + * VIA VT82C586a - Added UDMA to 33Mhz + * VIA VT82C586b - UDMA33 + * VIA VT82C596a - Nonfunctional UDMA66 + * VIA VT82C596b - Working UDMA66 + * VIA VT82C686 - Nonfunctional UDMA66 + * VIA VT82C686a - Working UDMA66 + * VIA VT82C686b - Updated to UDMA100 + * VIA VT8231 - UDMA100 + * VIA VT8233 - UDMA100 + * VIA VT8233a - UDMA133 + * VIA VT8233c - UDMA100 + * VIA VT8235 - UDMA133 + * VIA VT8237 - UDMA133 + * + * Most registers remain compatible across chips. Others start reserved + * and acquire sensible semantics if set to 1 (eg cable detect). A few + * exceptions exist, notably around the FIFO settings. + * + * One additional quirk of the VIA design is that like ALi they use few + * PCI IDs for a lot of chips. + * + * Based heavily on: + * + * Version 3.38 + * + * VIA IDE driver for Linux. Supported southbridges: + * + * vt82c576, vt82c586, vt82c586a, vt82c586b, vt82c596a, vt82c596b, + * vt82c686, vt82c686a, vt82c686b, vt8231, vt8233, vt8233c, vt8233a, + * vt8235, vt8237 + * + * Copyright (c) 2000-2002 Vojtech Pavlik + * + * Based on the work of: + * Michel Aubry + * Jeff Garzik + * Andre Hedrick + + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_via" +#define DRV_VERSION "0.1.14" + +/* + * The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx + * driver. + */ + +enum { + VIA_UDMA = 0x007, + VIA_UDMA_NONE = 0x000, + VIA_UDMA_33 = 0x001, + VIA_UDMA_66 = 0x002, + VIA_UDMA_100 = 0x003, + VIA_UDMA_133 = 0x004, + VIA_BAD_PREQ = 0x010, /* Crashes if PREQ# till DDACK# set */ + VIA_BAD_CLK66 = 0x020, /* 66 MHz clock doesn't work correctly */ + VIA_SET_FIFO = 0x040, /* Needs to have FIFO split set */ + VIA_NO_UNMASK = 0x080, /* Doesn't work with IRQ unmasking on */ + VIA_BAD_ID = 0x100, /* Has wrong vendor ID (0x1107) */ + VIA_BAD_AST = 0x200, /* Don't touch Address Setup Timing */ + VIA_NO_ENABLES = 0x400, /* Has no enablebits */ +}; + +/* + * VIA SouthBridge chips. + */ + +static const struct via_isa_bridge { + const char *name; + u16 id; + u8 rev_min; + u8 rev_max; + u16 flags; +} via_isa_bridges[] = { + { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, + { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES}, + { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, + { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, + { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, + { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, + { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, VIA_UDMA_100 }, + { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, VIA_UDMA_100 }, + { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, VIA_UDMA_100 }, + { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, VIA_UDMA_100 }, + { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, VIA_UDMA_66 }, + { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 }, + { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, VIA_UDMA_66 }, + { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 }, + { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, VIA_UDMA_33 | VIA_SET_FIFO }, + { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, VIA_UDMA_33 | VIA_SET_FIFO | VIA_BAD_PREQ }, + { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, VIA_UDMA_33 | VIA_SET_FIFO }, + { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, VIA_UDMA_33 | VIA_SET_FIFO }, + { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, VIA_UDMA_NONE | VIA_SET_FIFO }, + { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK }, + { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID }, + { NULL } +}; + +/** + * via_cable_detect - cable detection + * @ap: ATA port + * + * Perform cable detection. Actually for the VIA case the BIOS + * already did this for us. We read the values provided by the + * BIOS. If you are using an 8235 in a non-PC configuration you + * may need to update this code. + * + * Hotplug also impacts on this. + */ + +static int via_cable_detect(struct ata_port *ap) { + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 ata66; + + pci_read_config_dword(pdev, 0x50, &ata66); + /* Check both the drive cable reporting bits, we might not have + two drives */ + if (ata66 & (0x10100000 >> (16 * ap->port_no))) + return ATA_CBL_PATA80; + else + return ATA_CBL_PATA40; +} + +static int via_pre_reset(struct ata_port *ap) +{ + const struct via_isa_bridge *config = ap->host->private_data; + + if (!(config->flags & VIA_NO_ENABLES)) { + static const struct pci_bits via_enable_bits[] = { + { 0x40, 1, 0x02, 0x02 }, + { 0x40, 1, 0x01, 0x01 } + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no])) + return -ENOENT; + } + + if ((config->flags & VIA_UDMA) >= VIA_UDMA_66) + ap->cbl = via_cable_detect(ap); + else + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + + +/** + * via_error_handler - reset for VIA chips + * @ap: ATA port + * + * Handle the reset callback for the later chips with cable detect + */ + +static void via_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, via_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * via_do_set_mode - set initial PIO mode data + * @ap: ATA interface + * @adev: ATA device + * @mode: ATA mode being programmed + * @tdiv: Clocks per PCI clock + * @set_ast: Set to program address setup + * @udma_type: UDMA mode/format of registers + * + * Program the VIA registers for DMA and PIO modes. Uses the ata timing + * support in order to compute modes. + * + * FIXME: Hotplug will require we serialize multiple mode changes + * on the two channels. + */ + +static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mode, int tdiv, int set_ast, int udma_type) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct ata_device *peer = ata_dev_pair(adev); + struct ata_timing t, p; + static int via_clock = 33333; /* Bus clock in kHZ - ought to be tunable one day */ + unsigned long T = 1000000000 / via_clock; + unsigned long UT = T/tdiv; + int ut; + int offset = 3 - (2*ap->port_no) - adev->devno; + + + /* Calculate the timing values we require */ + ata_timing_compute(adev, mode, &t, T, UT); + + /* We share 8bit timing so we must merge the constraints */ + if (peer) { + if (peer->pio_mode) { + ata_timing_compute(peer, peer->pio_mode, &p, T, UT); + ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT); + } + } + + /* Address setup is programmable but breaks on UDMA133 setups */ + if (set_ast) { + u8 setup; /* 2 bits per drive */ + int shift = 2 * offset; + + pci_read_config_byte(pdev, 0x4C, &setup); + setup &= ~(3 << shift); + setup |= FIT(t.setup, 1, 4) << shift; /* 1,4 or 1,4 - 1 FIXME */ + pci_write_config_byte(pdev, 0x4C, setup); + } + + /* Load the PIO mode bits */ + pci_write_config_byte(pdev, 0x4F - ap->port_no, + ((FIT(t.act8b, 1, 16) - 1) << 4) | (FIT(t.rec8b, 1, 16) - 1)); + pci_write_config_byte(pdev, 0x48 + offset, + ((FIT(t.active, 1, 16) - 1) << 4) | (FIT(t.recover, 1, 16) - 1)); + + /* Load the UDMA bits according to type */ + switch(udma_type) { + default: + /* BUG() ? */ + /* fall through */ + case 33: + ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 5) - 2)) : 0x03; + break; + case 66: + ut = t.udma ? (0xe8 | (FIT(t.udma, 2, 9) - 2)) : 0x0f; + break; + case 100: + ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07; + break; + case 133: + ut = t.udma ? (0xe0 | (FIT(t.udma, 2, 9) - 2)) : 0x07; + break; + } + /* Set UDMA unless device is not UDMA capable */ + if (udma_type) + pci_write_config_byte(pdev, 0x50 + offset, ut); +} + +static void via_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + const struct via_isa_bridge *config = ap->host->private_data; + int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; + int mode = config->flags & VIA_UDMA; + static u8 tclock[5] = { 1, 1, 2, 3, 4 }; + static u8 udma[5] = { 0, 33, 66, 100, 133 }; + + via_do_set_mode(ap, adev, adev->pio_mode, tclock[mode], set_ast, udma[mode]); +} + +static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + const struct via_isa_bridge *config = ap->host->private_data; + int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; + int mode = config->flags & VIA_UDMA; + static u8 tclock[5] = { 1, 1, 2, 3, 4 }; + static u8 udma[5] = { 0, 33, 66, 100, 133 }; + + via_do_set_mode(ap, adev, adev->dma_mode, tclock[mode], set_ast, udma[mode]); +} + +static struct scsi_host_template via_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations via_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = via_set_piomode, + .set_dmamode = via_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = via_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +static struct ata_port_operations via_port_ops_noirq = { + .port_disable = ata_port_disable, + .set_piomode = via_set_piomode, + .set_dmamode = via_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = via_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .data_xfer = ata_pio_data_xfer_noirq, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * via_init_one - discovery callback + * @pdev: PCI device ID + * @id: PCI table info + * + * A VIA IDE interface has been discovered. Figure out what revision + * and perform configuration work before handing it to the ATA layer + */ + +static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + /* Early VIA without UDMA support */ + static struct ata_port_info via_mwdma_info = { + .sht = &via_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &via_port_ops + }; + /* Ditto with IRQ masking required */ + static struct ata_port_info via_mwdma_info_borked = { + .sht = &via_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .port_ops = &via_port_ops_noirq, + }; + /* VIA UDMA 33 devices (and borked 66) */ + static struct ata_port_info via_udma33_info = { + .sht = &via_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7, + .port_ops = &via_port_ops + }; + /* VIA UDMA 66 devices */ + static struct ata_port_info via_udma66_info = { + .sht = &via_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x1f, + .port_ops = &via_port_ops + }; + /* VIA UDMA 100 devices */ + static struct ata_port_info via_udma100_info = { + .sht = &via_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &via_port_ops + }; + /* UDMA133 with bad AST (All current 133) */ + static struct ata_port_info via_udma133_info = { + .sht = &via_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, /* FIXME: should check north bridge */ + .port_ops = &via_port_ops + }; + struct ata_port_info *port_info[2], *type; + struct pci_dev *isa = NULL; + const struct via_isa_bridge *config; + static int printed_version; + u8 t; + u8 enable; + u32 timing; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + /* To find out how the IDE will behave and what features we + actually have to look at the bridge not the IDE controller */ + for (config = via_isa_bridges; config->id; config++) + if ((isa = pci_get_device(PCI_VENDOR_ID_VIA + + !!(config->flags & VIA_BAD_ID), + config->id, NULL))) { + + pci_read_config_byte(isa, PCI_REVISION_ID, &t); + if (t >= config->rev_min && + t <= config->rev_max) + break; + pci_dev_put(isa); + } + + if (!config->id) { + printk(KERN_WARNING "via: Unknown VIA SouthBridge, disabling.\n"); + return -ENODEV; + } + pci_dev_put(isa); + + /* 0x40 low bits indicate enabled channels */ + pci_read_config_byte(pdev, 0x40 , &enable); + enable &= 3; + if (enable == 0) { + return -ENODEV; + } + + /* Initialise the FIFO for the enabled channels. */ + if (config->flags & VIA_SET_FIFO) { + u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20}; + u8 fifo; + + pci_read_config_byte(pdev, 0x43, &fifo); + + /* Clear PREQ# until DDACK# for errata */ + if (config->flags & VIA_BAD_PREQ) + fifo &= 0x7F; + else + fifo &= 0x9f; + /* Turn on FIFO for enabled channels */ + fifo |= fifo_setting[enable]; + pci_write_config_byte(pdev, 0x43, fifo); + } + /* Clock set up */ + switch(config->flags & VIA_UDMA) { + case VIA_UDMA_NONE: + if (config->flags & VIA_NO_UNMASK) + type = &via_mwdma_info_borked; + else + type = &via_mwdma_info; + break; + case VIA_UDMA_33: + type = &via_udma33_info; + break; + case VIA_UDMA_66: + type = &via_udma66_info; + /* The 66 MHz devices require we enable the clock */ + pci_read_config_dword(pdev, 0x50, &timing); + timing |= 0x80008; + pci_write_config_dword(pdev, 0x50, timing); + break; + case VIA_UDMA_100: + type = &via_udma100_info; + break; + case VIA_UDMA_133: + type = &via_udma133_info; + break; + default: + WARN_ON(1); + return -ENODEV; + } + + if (config->flags & VIA_BAD_CLK66) { + /* Disable the 66MHz clock on problem devices */ + pci_read_config_dword(pdev, 0x50, &timing); + timing &= ~0x80008; + pci_write_config_dword(pdev, 0x50, timing); + } + + /* We have established the device type, now fire it up */ + type->private_data = (void *)config; + + port_info[0] = port_info[1] = type; + return ata_pci_init_one(pdev, port_info, 2); +} + +static const struct pci_device_id via[] = { + { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576_1), }, + { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1), }, + { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_6410), }, + { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_SATA_EIDE), }, + { 0, }, +}; + +static struct pci_driver via_pci_driver = { + .name = DRV_NAME, + .id_table = via, + .probe = via_init_one, + .remove = ata_pci_remove_one +}; + +static int __init via_init(void) +{ + return pci_register_driver(&via_pci_driver); +} + + +static void __exit via_exit(void) +{ + pci_unregister_driver(&via_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for VIA PATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, via); +MODULE_VERSION(DRV_VERSION); + +module_init(via_init); +module_exit(via_exit); diff --git a/drivers/ata/pdc_adma.c b/drivers/ata/pdc_adma.c new file mode 100644 index 00000000000..0e23ecb77bc --- /dev/null +++ b/drivers/ata/pdc_adma.c @@ -0,0 +1,740 @@ +/* + * pdc_adma.c - Pacific Digital Corporation ADMA + * + * Maintained by: Mark Lord <mlord@pobox.com> + * + * Copyright 2005 Mark Lord + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * + * Supports ATA disks in single-packet ADMA mode. + * Uses PIO for everything else. + * + * TODO: Use ADMA transfers for ATAPI devices, when possible. + * This requires careful attention to a number of quirks of the chip. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <asm/io.h> +#include <linux/libata.h> + +#define DRV_NAME "pdc_adma" +#define DRV_VERSION "0.04" + +/* macro to calculate base address for ATA regs */ +#define ADMA_ATA_REGS(base,port_no) ((base) + ((port_no) * 0x40)) + +/* macro to calculate base address for ADMA regs */ +#define ADMA_REGS(base,port_no) ((base) + 0x80 + ((port_no) * 0x20)) + +enum { + ADMA_PORTS = 2, + ADMA_CPB_BYTES = 40, + ADMA_PRD_BYTES = LIBATA_MAX_PRD * 16, + ADMA_PKT_BYTES = ADMA_CPB_BYTES + ADMA_PRD_BYTES, + + ADMA_DMA_BOUNDARY = 0xffffffff, + + /* global register offsets */ + ADMA_MODE_LOCK = 0x00c7, + + /* per-channel register offsets */ + ADMA_CONTROL = 0x0000, /* ADMA control */ + ADMA_STATUS = 0x0002, /* ADMA status */ + ADMA_CPB_COUNT = 0x0004, /* CPB count */ + ADMA_CPB_CURRENT = 0x000c, /* current CPB address */ + ADMA_CPB_NEXT = 0x000c, /* next CPB address */ + ADMA_CPB_LOOKUP = 0x0010, /* CPB lookup table */ + ADMA_FIFO_IN = 0x0014, /* input FIFO threshold */ + ADMA_FIFO_OUT = 0x0016, /* output FIFO threshold */ + + /* ADMA_CONTROL register bits */ + aNIEN = (1 << 8), /* irq mask: 1==masked */ + aGO = (1 << 7), /* packet trigger ("Go!") */ + aRSTADM = (1 << 5), /* ADMA logic reset */ + aPIOMD4 = 0x0003, /* PIO mode 4 */ + + /* ADMA_STATUS register bits */ + aPSD = (1 << 6), + aUIRQ = (1 << 4), + aPERR = (1 << 0), + + /* CPB bits */ + cDONE = (1 << 0), + cVLD = (1 << 0), + cDAT = (1 << 2), + cIEN = (1 << 3), + + /* PRD bits */ + pORD = (1 << 4), + pDIRO = (1 << 5), + pEND = (1 << 7), + + /* ATA register flags */ + rIGN = (1 << 5), + rEND = (1 << 7), + + /* ATA register addresses */ + ADMA_REGS_CONTROL = 0x0e, + ADMA_REGS_SECTOR_COUNT = 0x12, + ADMA_REGS_LBA_LOW = 0x13, + ADMA_REGS_LBA_MID = 0x14, + ADMA_REGS_LBA_HIGH = 0x15, + ADMA_REGS_DEVICE = 0x16, + ADMA_REGS_COMMAND = 0x17, + + /* PCI device IDs */ + board_1841_idx = 0, /* ADMA 2-port controller */ +}; + +typedef enum { adma_state_idle, adma_state_pkt, adma_state_mmio } adma_state_t; + +struct adma_port_priv { + u8 *pkt; + dma_addr_t pkt_dma; + adma_state_t state; +}; + +static int adma_ata_init_one (struct pci_dev *pdev, + const struct pci_device_id *ent); +static irqreturn_t adma_intr (int irq, void *dev_instance, + struct pt_regs *regs); +static int adma_port_start(struct ata_port *ap); +static void adma_host_stop(struct ata_host *host); +static void adma_port_stop(struct ata_port *ap); +static void adma_phy_reset(struct ata_port *ap); +static void adma_qc_prep(struct ata_queued_cmd *qc); +static unsigned int adma_qc_issue(struct ata_queued_cmd *qc); +static int adma_check_atapi_dma(struct ata_queued_cmd *qc); +static void adma_bmdma_stop(struct ata_queued_cmd *qc); +static u8 adma_bmdma_status(struct ata_port *ap); +static void adma_irq_clear(struct ata_port *ap); +static void adma_eng_timeout(struct ata_port *ap); + +static struct scsi_host_template adma_ata_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ENABLE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ADMA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations adma_ata_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .check_atapi_dma = adma_check_atapi_dma, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .phy_reset = adma_phy_reset, + .qc_prep = adma_qc_prep, + .qc_issue = adma_qc_issue, + .eng_timeout = adma_eng_timeout, + .data_xfer = ata_mmio_data_xfer, + .irq_handler = adma_intr, + .irq_clear = adma_irq_clear, + .port_start = adma_port_start, + .port_stop = adma_port_stop, + .host_stop = adma_host_stop, + .bmdma_stop = adma_bmdma_stop, + .bmdma_status = adma_bmdma_status, +}; + +static struct ata_port_info adma_port_info[] = { + /* board_1841_idx */ + { + .sht = &adma_ata_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST | + ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | + ATA_FLAG_PIO_POLLING, + .pio_mask = 0x10, /* pio4 */ + .udma_mask = 0x1f, /* udma0-4 */ + .port_ops = &adma_ata_ops, + }, +}; + +static const struct pci_device_id adma_ata_pci_tbl[] = { + { PCI_VENDOR_ID_PDC, 0x1841, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_1841_idx }, + + { } /* terminate list */ +}; + +static struct pci_driver adma_ata_pci_driver = { + .name = DRV_NAME, + .id_table = adma_ata_pci_tbl, + .probe = adma_ata_init_one, + .remove = ata_pci_remove_one, +}; + +static int adma_check_atapi_dma(struct ata_queued_cmd *qc) +{ + return 1; /* ATAPI DMA not yet supported */ +} + +static void adma_bmdma_stop(struct ata_queued_cmd *qc) +{ + /* nothing */ +} + +static u8 adma_bmdma_status(struct ata_port *ap) +{ + return 0; +} + +static void adma_irq_clear(struct ata_port *ap) +{ + /* nothing */ +} + +static void adma_reset_engine(void __iomem *chan) +{ + /* reset ADMA to idle state */ + writew(aPIOMD4 | aNIEN | aRSTADM, chan + ADMA_CONTROL); + udelay(2); + writew(aPIOMD4, chan + ADMA_CONTROL); + udelay(2); +} + +static void adma_reinit_engine(struct ata_port *ap) +{ + struct adma_port_priv *pp = ap->private_data; + void __iomem *mmio_base = ap->host->mmio_base; + void __iomem *chan = ADMA_REGS(mmio_base, ap->port_no); + + /* mask/clear ATA interrupts */ + writeb(ATA_NIEN, (void __iomem *)ap->ioaddr.ctl_addr); + ata_check_status(ap); + + /* reset the ADMA engine */ + adma_reset_engine(chan); + + /* set in-FIFO threshold to 0x100 */ + writew(0x100, chan + ADMA_FIFO_IN); + + /* set CPB pointer */ + writel((u32)pp->pkt_dma, chan + ADMA_CPB_NEXT); + + /* set out-FIFO threshold to 0x100 */ + writew(0x100, chan + ADMA_FIFO_OUT); + + /* set CPB count */ + writew(1, chan + ADMA_CPB_COUNT); + + /* read/discard ADMA status */ + readb(chan + ADMA_STATUS); +} + +static inline void adma_enter_reg_mode(struct ata_port *ap) +{ + void __iomem *chan = ADMA_REGS(ap->host->mmio_base, ap->port_no); + + writew(aPIOMD4, chan + ADMA_CONTROL); + readb(chan + ADMA_STATUS); /* flush */ +} + +static void adma_phy_reset(struct ata_port *ap) +{ + struct adma_port_priv *pp = ap->private_data; + + pp->state = adma_state_idle; + adma_reinit_engine(ap); + ata_port_probe(ap); + ata_bus_reset(ap); +} + +static void adma_eng_timeout(struct ata_port *ap) +{ + struct adma_port_priv *pp = ap->private_data; + + if (pp->state != adma_state_idle) /* healthy paranoia */ + pp->state = adma_state_mmio; + adma_reinit_engine(ap); + ata_eng_timeout(ap); +} + +static int adma_fill_sg(struct ata_queued_cmd *qc) +{ + struct scatterlist *sg; + struct ata_port *ap = qc->ap; + struct adma_port_priv *pp = ap->private_data; + u8 *buf = pp->pkt; + int i = (2 + buf[3]) * 8; + u8 pFLAGS = pORD | ((qc->tf.flags & ATA_TFLAG_WRITE) ? pDIRO : 0); + + ata_for_each_sg(sg, qc) { + u32 addr; + u32 len; + + addr = (u32)sg_dma_address(sg); + *(__le32 *)(buf + i) = cpu_to_le32(addr); + i += 4; + + len = sg_dma_len(sg) >> 3; + *(__le32 *)(buf + i) = cpu_to_le32(len); + i += 4; + + if (ata_sg_is_last(sg, qc)) + pFLAGS |= pEND; + buf[i++] = pFLAGS; + buf[i++] = qc->dev->dma_mode & 0xf; + buf[i++] = 0; /* pPKLW */ + buf[i++] = 0; /* reserved */ + + *(__le32 *)(buf + i) + = (pFLAGS & pEND) ? 0 : cpu_to_le32(pp->pkt_dma + i + 4); + i += 4; + + VPRINTK("PRD[%u] = (0x%lX, 0x%X)\n", i/4, + (unsigned long)addr, len); + } + return i; +} + +static void adma_qc_prep(struct ata_queued_cmd *qc) +{ + struct adma_port_priv *pp = qc->ap->private_data; + u8 *buf = pp->pkt; + u32 pkt_dma = (u32)pp->pkt_dma; + int i = 0; + + VPRINTK("ENTER\n"); + + adma_enter_reg_mode(qc->ap); + if (qc->tf.protocol != ATA_PROT_DMA) { + ata_qc_prep(qc); + return; + } + + buf[i++] = 0; /* Response flags */ + buf[i++] = 0; /* reserved */ + buf[i++] = cVLD | cDAT | cIEN; + i++; /* cLEN, gets filled in below */ + + *(__le32 *)(buf+i) = cpu_to_le32(pkt_dma); /* cNCPB */ + i += 4; /* cNCPB */ + i += 4; /* cPRD, gets filled in below */ + + buf[i++] = 0; /* reserved */ + buf[i++] = 0; /* reserved */ + buf[i++] = 0; /* reserved */ + buf[i++] = 0; /* reserved */ + + /* ATA registers; must be a multiple of 4 */ + buf[i++] = qc->tf.device; + buf[i++] = ADMA_REGS_DEVICE; + if ((qc->tf.flags & ATA_TFLAG_LBA48)) { + buf[i++] = qc->tf.hob_nsect; + buf[i++] = ADMA_REGS_SECTOR_COUNT; + buf[i++] = qc->tf.hob_lbal; + buf[i++] = ADMA_REGS_LBA_LOW; + buf[i++] = qc->tf.hob_lbam; + buf[i++] = ADMA_REGS_LBA_MID; + buf[i++] = qc->tf.hob_lbah; + buf[i++] = ADMA_REGS_LBA_HIGH; + } + buf[i++] = qc->tf.nsect; + buf[i++] = ADMA_REGS_SECTOR_COUNT; + buf[i++] = qc->tf.lbal; + buf[i++] = ADMA_REGS_LBA_LOW; + buf[i++] = qc->tf.lbam; + buf[i++] = ADMA_REGS_LBA_MID; + buf[i++] = qc->tf.lbah; + buf[i++] = ADMA_REGS_LBA_HIGH; + buf[i++] = 0; + buf[i++] = ADMA_REGS_CONTROL; + buf[i++] = rIGN; + buf[i++] = 0; + buf[i++] = qc->tf.command; + buf[i++] = ADMA_REGS_COMMAND | rEND; + + buf[3] = (i >> 3) - 2; /* cLEN */ + *(__le32 *)(buf+8) = cpu_to_le32(pkt_dma + i); /* cPRD */ + + i = adma_fill_sg(qc); + wmb(); /* flush PRDs and pkt to memory */ +#if 0 + /* dump out CPB + PRDs for debug */ + { + int j, len = 0; + static char obuf[2048]; + for (j = 0; j < i; ++j) { + len += sprintf(obuf+len, "%02x ", buf[j]); + if ((j & 7) == 7) { + printk("%s\n", obuf); + len = 0; + } + } + if (len) + printk("%s\n", obuf); + } +#endif +} + +static inline void adma_packet_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *chan = ADMA_REGS(ap->host->mmio_base, ap->port_no); + + VPRINTK("ENTER, ap %p\n", ap); + + /* fire up the ADMA engine */ + writew(aPIOMD4 | aGO, chan + ADMA_CONTROL); +} + +static unsigned int adma_qc_issue(struct ata_queued_cmd *qc) +{ + struct adma_port_priv *pp = qc->ap->private_data; + + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + pp->state = adma_state_pkt; + adma_packet_start(qc); + return 0; + + case ATA_PROT_ATAPI_DMA: + BUG(); + break; + + default: + break; + } + + pp->state = adma_state_mmio; + return ata_qc_issue_prot(qc); +} + +static inline unsigned int adma_intr_pkt(struct ata_host *host) +{ + unsigned int handled = 0, port_no; + u8 __iomem *mmio_base = host->mmio_base; + + for (port_no = 0; port_no < host->n_ports; ++port_no) { + struct ata_port *ap = host->ports[port_no]; + struct adma_port_priv *pp; + struct ata_queued_cmd *qc; + void __iomem *chan = ADMA_REGS(mmio_base, port_no); + u8 status = readb(chan + ADMA_STATUS); + + if (status == 0) + continue; + handled = 1; + adma_enter_reg_mode(ap); + if (ap->flags & ATA_FLAG_DISABLED) + continue; + pp = ap->private_data; + if (!pp || pp->state != adma_state_pkt) + continue; + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) { + if ((status & (aPERR | aPSD | aUIRQ))) + qc->err_mask |= AC_ERR_OTHER; + else if (pp->pkt[0] != cDONE) + qc->err_mask |= AC_ERR_OTHER; + + ata_qc_complete(qc); + } + } + return handled; +} + +static inline unsigned int adma_intr_mmio(struct ata_host *host) +{ + unsigned int handled = 0, port_no; + + for (port_no = 0; port_no < host->n_ports; ++port_no) { + struct ata_port *ap; + ap = host->ports[port_no]; + if (ap && (!(ap->flags & ATA_FLAG_DISABLED))) { + struct ata_queued_cmd *qc; + struct adma_port_priv *pp = ap->private_data; + if (!pp || pp->state != adma_state_mmio) + continue; + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) { + + /* check main status, clearing INTRQ */ + u8 status = ata_check_status(ap); + if ((status & ATA_BUSY)) + continue; + DPRINTK("ata%u: protocol %d (dev_stat 0x%X)\n", + ap->id, qc->tf.protocol, status); + + /* complete taskfile transaction */ + pp->state = adma_state_idle; + qc->err_mask |= ac_err_mask(status); + ata_qc_complete(qc); + handled = 1; + } + } + } + return handled; +} + +static irqreturn_t adma_intr(int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + unsigned int handled = 0; + + VPRINTK("ENTER\n"); + + spin_lock(&host->lock); + handled = adma_intr_pkt(host) | adma_intr_mmio(host); + spin_unlock(&host->lock); + + VPRINTK("EXIT\n"); + + return IRQ_RETVAL(handled); +} + +static void adma_ata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = + port->data_addr = base + 0x000; + port->error_addr = + port->feature_addr = base + 0x004; + port->nsect_addr = base + 0x008; + port->lbal_addr = base + 0x00c; + port->lbam_addr = base + 0x010; + port->lbah_addr = base + 0x014; + port->device_addr = base + 0x018; + port->status_addr = + port->command_addr = base + 0x01c; + port->altstatus_addr = + port->ctl_addr = base + 0x038; +} + +static int adma_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct adma_port_priv *pp; + int rc; + + rc = ata_port_start(ap); + if (rc) + return rc; + adma_enter_reg_mode(ap); + rc = -ENOMEM; + pp = kcalloc(1, sizeof(*pp), GFP_KERNEL); + if (!pp) + goto err_out; + pp->pkt = dma_alloc_coherent(dev, ADMA_PKT_BYTES, &pp->pkt_dma, + GFP_KERNEL); + if (!pp->pkt) + goto err_out_kfree; + /* paranoia? */ + if ((pp->pkt_dma & 7) != 0) { + printk("bad alignment for pp->pkt_dma: %08x\n", + (u32)pp->pkt_dma); + dma_free_coherent(dev, ADMA_PKT_BYTES, + pp->pkt, pp->pkt_dma); + goto err_out_kfree; + } + memset(pp->pkt, 0, ADMA_PKT_BYTES); + ap->private_data = pp; + adma_reinit_engine(ap); + return 0; + +err_out_kfree: + kfree(pp); +err_out: + ata_port_stop(ap); + return rc; +} + +static void adma_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct adma_port_priv *pp = ap->private_data; + + adma_reset_engine(ADMA_REGS(ap->host->mmio_base, ap->port_no)); + if (pp != NULL) { + ap->private_data = NULL; + if (pp->pkt != NULL) + dma_free_coherent(dev, ADMA_PKT_BYTES, + pp->pkt, pp->pkt_dma); + kfree(pp); + } + ata_port_stop(ap); +} + +static void adma_host_stop(struct ata_host *host) +{ + unsigned int port_no; + + for (port_no = 0; port_no < ADMA_PORTS; ++port_no) + adma_reset_engine(ADMA_REGS(host->mmio_base, port_no)); + + ata_pci_host_stop(host); +} + +static void adma_host_init(unsigned int chip_id, + struct ata_probe_ent *probe_ent) +{ + unsigned int port_no; + void __iomem *mmio_base = probe_ent->mmio_base; + + /* enable/lock aGO operation */ + writeb(7, mmio_base + ADMA_MODE_LOCK); + + /* reset the ADMA logic */ + for (port_no = 0; port_no < ADMA_PORTS; ++port_no) + adma_reset_engine(ADMA_REGS(mmio_base, port_no)); +} + +static int adma_set_dma_masks(struct pci_dev *pdev, void __iomem *mmio_base) +{ + int rc; + + rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit DMA enable failed\n"); + return rc; + } + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit consistent DMA enable failed\n"); + return rc; + } + return 0; +} + +static int adma_ata_init_one(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + void __iomem *mmio_base; + unsigned int board_idx = (unsigned int) ent->driver_data; + int rc, port_no; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto err_out; + + if ((pci_resource_flags(pdev, 4) & IORESOURCE_MEM) == 0) { + rc = -ENODEV; + goto err_out_regions; + } + + mmio_base = pci_iomap(pdev, 4, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + rc = adma_set_dma_masks(pdev, mmio_base); + if (rc) + goto err_out_iounmap; + + probe_ent = kcalloc(1, sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_iounmap; + } + + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + probe_ent->sht = adma_port_info[board_idx].sht; + probe_ent->port_flags = adma_port_info[board_idx].flags; + probe_ent->pio_mask = adma_port_info[board_idx].pio_mask; + probe_ent->mwdma_mask = adma_port_info[board_idx].mwdma_mask; + probe_ent->udma_mask = adma_port_info[board_idx].udma_mask; + probe_ent->port_ops = adma_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + probe_ent->n_ports = ADMA_PORTS; + + for (port_no = 0; port_no < probe_ent->n_ports; ++port_no) { + adma_ata_setup_port(&probe_ent->port[port_no], + ADMA_ATA_REGS((unsigned long)mmio_base, port_no)); + } + + pci_set_master(pdev); + + /* initialize adapter */ + adma_host_init(board_idx, probe_ent); + + rc = ata_device_add(probe_ent); + kfree(probe_ent); + if (rc != ADMA_PORTS) + goto err_out_iounmap; + return 0; + +err_out_iounmap: + pci_iounmap(pdev, mmio_base); +err_out_regions: + pci_release_regions(pdev); +err_out: + pci_disable_device(pdev); + return rc; +} + +static int __init adma_ata_init(void) +{ + return pci_register_driver(&adma_ata_pci_driver); +} + +static void __exit adma_ata_exit(void) +{ + pci_unregister_driver(&adma_ata_pci_driver); +} + +MODULE_AUTHOR("Mark Lord"); +MODULE_DESCRIPTION("Pacific Digital Corporation ADMA low-level driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, adma_ata_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_init(adma_ata_init); +module_exit(adma_ata_exit); diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c new file mode 100644 index 00000000000..c01496df4a9 --- /dev/null +++ b/drivers/ata/sata_mv.c @@ -0,0 +1,2466 @@ +/* + * sata_mv.c - Marvell SATA support + * + * Copyright 2005: EMC Corporation, all rights reserved. + * Copyright 2005 Red Hat, Inc. All rights reserved. + * + * Please ALWAYS copy linux-ide@vger.kernel.org on emails. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/dma-mapping.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <linux/libata.h> +#include <asm/io.h> + +#define DRV_NAME "sata_mv" +#define DRV_VERSION "0.7" + +enum { + /* BAR's are enumerated in terms of pci_resource_start() terms */ + MV_PRIMARY_BAR = 0, /* offset 0x10: memory space */ + MV_IO_BAR = 2, /* offset 0x18: IO space */ + MV_MISC_BAR = 3, /* offset 0x1c: FLASH, NVRAM, SRAM */ + + MV_MAJOR_REG_AREA_SZ = 0x10000, /* 64KB */ + MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */ + + MV_PCI_REG_BASE = 0, + MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */ + MV_IRQ_COAL_CAUSE = (MV_IRQ_COAL_REG_BASE + 0x08), + MV_IRQ_COAL_CAUSE_LO = (MV_IRQ_COAL_REG_BASE + 0x88), + MV_IRQ_COAL_CAUSE_HI = (MV_IRQ_COAL_REG_BASE + 0x8c), + MV_IRQ_COAL_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xcc), + MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0), + + MV_SATAHC0_REG_BASE = 0x20000, + MV_FLASH_CTL = 0x1046c, + MV_GPIO_PORT_CTL = 0x104f0, + MV_RESET_CFG = 0x180d8, + + MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ, + MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ, + MV_SATAHC_ARBTR_REG_SZ = MV_MINOR_REG_AREA_SZ, /* arbiter */ + MV_PORT_REG_SZ = MV_MINOR_REG_AREA_SZ, + + MV_USE_Q_DEPTH = ATA_DEF_QUEUE, + + MV_MAX_Q_DEPTH = 32, + MV_MAX_Q_DEPTH_MASK = MV_MAX_Q_DEPTH - 1, + + /* CRQB needs alignment on a 1KB boundary. Size == 1KB + * CRPB needs alignment on a 256B boundary. Size == 256B + * SG count of 176 leads to MV_PORT_PRIV_DMA_SZ == 4KB + * ePRD (SG) entries need alignment on a 16B boundary. Size == 16B + */ + MV_CRQB_Q_SZ = (32 * MV_MAX_Q_DEPTH), + MV_CRPB_Q_SZ = (8 * MV_MAX_Q_DEPTH), + MV_MAX_SG_CT = 176, + MV_SG_TBL_SZ = (16 * MV_MAX_SG_CT), + MV_PORT_PRIV_DMA_SZ = (MV_CRQB_Q_SZ + MV_CRPB_Q_SZ + MV_SG_TBL_SZ), + + MV_PORTS_PER_HC = 4, + /* == (port / MV_PORTS_PER_HC) to determine HC from 0-7 port */ + MV_PORT_HC_SHIFT = 2, + /* == (port % MV_PORTS_PER_HC) to determine hard port from 0-7 port */ + MV_PORT_MASK = 3, + + /* Host Flags */ + MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */ + MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */ + MV_COMMON_FLAGS = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO | + ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING), + MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE, + + CRQB_FLAG_READ = (1 << 0), + CRQB_TAG_SHIFT = 1, + CRQB_CMD_ADDR_SHIFT = 8, + CRQB_CMD_CS = (0x2 << 11), + CRQB_CMD_LAST = (1 << 15), + + CRPB_FLAG_STATUS_SHIFT = 8, + + EPRD_FLAG_END_OF_TBL = (1 << 31), + + /* PCI interface registers */ + + PCI_COMMAND_OFS = 0xc00, + + PCI_MAIN_CMD_STS_OFS = 0xd30, + STOP_PCI_MASTER = (1 << 2), + PCI_MASTER_EMPTY = (1 << 3), + GLOB_SFT_RST = (1 << 4), + + MV_PCI_MODE = 0xd00, + MV_PCI_EXP_ROM_BAR_CTL = 0xd2c, + MV_PCI_DISC_TIMER = 0xd04, + MV_PCI_MSI_TRIGGER = 0xc38, + MV_PCI_SERR_MASK = 0xc28, + MV_PCI_XBAR_TMOUT = 0x1d04, + MV_PCI_ERR_LOW_ADDRESS = 0x1d40, + MV_PCI_ERR_HIGH_ADDRESS = 0x1d44, + MV_PCI_ERR_ATTRIBUTE = 0x1d48, + MV_PCI_ERR_COMMAND = 0x1d50, + + PCI_IRQ_CAUSE_OFS = 0x1d58, + PCI_IRQ_MASK_OFS = 0x1d5c, + PCI_UNMASK_ALL_IRQS = 0x7fffff, /* bits 22-0 */ + + HC_MAIN_IRQ_CAUSE_OFS = 0x1d60, + HC_MAIN_IRQ_MASK_OFS = 0x1d64, + PORT0_ERR = (1 << 0), /* shift by port # */ + PORT0_DONE = (1 << 1), /* shift by port # */ + HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */ + HC_SHIFT = 9, /* bits 9-17 = HC1's ports */ + PCI_ERR = (1 << 18), + TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */ + TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */ + PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */ + GPIO_INT = (1 << 22), + SELF_INT = (1 << 23), + TWSI_INT = (1 << 24), + HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */ + HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE | + PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT | + HC_MAIN_RSVD), + + /* SATAHC registers */ + HC_CFG_OFS = 0, + + HC_IRQ_CAUSE_OFS = 0x14, + CRPB_DMA_DONE = (1 << 0), /* shift by port # */ + HC_IRQ_COAL = (1 << 4), /* IRQ coalescing */ + DEV_IRQ = (1 << 8), /* shift by port # */ + + /* Shadow block registers */ + SHD_BLK_OFS = 0x100, + SHD_CTL_AST_OFS = 0x20, /* ofs from SHD_BLK_OFS */ + + /* SATA registers */ + SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */ + SATA_ACTIVE_OFS = 0x350, + PHY_MODE3 = 0x310, + PHY_MODE4 = 0x314, + PHY_MODE2 = 0x330, + MV5_PHY_MODE = 0x74, + MV5_LT_MODE = 0x30, + MV5_PHY_CTL = 0x0C, + SATA_INTERFACE_CTL = 0x050, + + MV_M2_PREAMP_MASK = 0x7e0, + + /* Port registers */ + EDMA_CFG_OFS = 0, + EDMA_CFG_Q_DEPTH = 0, /* queueing disabled */ + EDMA_CFG_NCQ = (1 << 5), + EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */ + EDMA_CFG_RD_BRST_EXT = (1 << 11), /* read burst 512B */ + EDMA_CFG_WR_BUFF_LEN = (1 << 13), /* write buffer 512B */ + + EDMA_ERR_IRQ_CAUSE_OFS = 0x8, + EDMA_ERR_IRQ_MASK_OFS = 0xc, + EDMA_ERR_D_PAR = (1 << 0), + EDMA_ERR_PRD_PAR = (1 << 1), + EDMA_ERR_DEV = (1 << 2), + EDMA_ERR_DEV_DCON = (1 << 3), + EDMA_ERR_DEV_CON = (1 << 4), + EDMA_ERR_SERR = (1 << 5), + EDMA_ERR_SELF_DIS = (1 << 7), + EDMA_ERR_BIST_ASYNC = (1 << 8), + EDMA_ERR_CRBQ_PAR = (1 << 9), + EDMA_ERR_CRPB_PAR = (1 << 10), + EDMA_ERR_INTRL_PAR = (1 << 11), + EDMA_ERR_IORDY = (1 << 12), + EDMA_ERR_LNK_CTRL_RX = (0xf << 13), + EDMA_ERR_LNK_CTRL_RX_2 = (1 << 15), + EDMA_ERR_LNK_DATA_RX = (0xf << 17), + EDMA_ERR_LNK_CTRL_TX = (0x1f << 21), + EDMA_ERR_LNK_DATA_TX = (0x1f << 26), + EDMA_ERR_TRANS_PROTO = (1 << 31), + EDMA_ERR_FATAL = (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR | + EDMA_ERR_DEV_DCON | EDMA_ERR_CRBQ_PAR | + EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR | + EDMA_ERR_IORDY | EDMA_ERR_LNK_CTRL_RX_2 | + EDMA_ERR_LNK_DATA_RX | + EDMA_ERR_LNK_DATA_TX | + EDMA_ERR_TRANS_PROTO), + + EDMA_REQ_Q_BASE_HI_OFS = 0x10, + EDMA_REQ_Q_IN_PTR_OFS = 0x14, /* also contains BASE_LO */ + + EDMA_REQ_Q_OUT_PTR_OFS = 0x18, + EDMA_REQ_Q_PTR_SHIFT = 5, + + EDMA_RSP_Q_BASE_HI_OFS = 0x1c, + EDMA_RSP_Q_IN_PTR_OFS = 0x20, + EDMA_RSP_Q_OUT_PTR_OFS = 0x24, /* also contains BASE_LO */ + EDMA_RSP_Q_PTR_SHIFT = 3, + + EDMA_CMD_OFS = 0x28, + EDMA_EN = (1 << 0), + EDMA_DS = (1 << 1), + ATA_RST = (1 << 2), + + EDMA_IORDY_TMOUT = 0x34, + EDMA_ARB_CFG = 0x38, + + /* Host private flags (hp_flags) */ + MV_HP_FLAG_MSI = (1 << 0), + MV_HP_ERRATA_50XXB0 = (1 << 1), + MV_HP_ERRATA_50XXB2 = (1 << 2), + MV_HP_ERRATA_60X1B2 = (1 << 3), + MV_HP_ERRATA_60X1C0 = (1 << 4), + MV_HP_ERRATA_XX42A0 = (1 << 5), + MV_HP_50XX = (1 << 6), + MV_HP_GEN_IIE = (1 << 7), + + /* Port private flags (pp_flags) */ + MV_PP_FLAG_EDMA_EN = (1 << 0), + MV_PP_FLAG_EDMA_DS_ACT = (1 << 1), +}; + +#define IS_50XX(hpriv) ((hpriv)->hp_flags & MV_HP_50XX) +#define IS_60XX(hpriv) (((hpriv)->hp_flags & MV_HP_50XX) == 0) +#define IS_GEN_I(hpriv) IS_50XX(hpriv) +#define IS_GEN_II(hpriv) IS_60XX(hpriv) +#define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE) + +enum { + /* Our DMA boundary is determined by an ePRD being unable to handle + * anything larger than 64KB + */ + MV_DMA_BOUNDARY = 0xffffU, + + EDMA_REQ_Q_BASE_LO_MASK = 0xfffffc00U, + + EDMA_RSP_Q_BASE_LO_MASK = 0xffffff00U, +}; + +enum chip_type { + chip_504x, + chip_508x, + chip_5080, + chip_604x, + chip_608x, + chip_6042, + chip_7042, +}; + +/* Command ReQuest Block: 32B */ +struct mv_crqb { + __le32 sg_addr; + __le32 sg_addr_hi; + __le16 ctrl_flags; + __le16 ata_cmd[11]; +}; + +struct mv_crqb_iie { + __le32 addr; + __le32 addr_hi; + __le32 flags; + __le32 len; + __le32 ata_cmd[4]; +}; + +/* Command ResPonse Block: 8B */ +struct mv_crpb { + __le16 id; + __le16 flags; + __le32 tmstmp; +}; + +/* EDMA Physical Region Descriptor (ePRD); A.K.A. SG */ +struct mv_sg { + __le32 addr; + __le32 flags_size; + __le32 addr_hi; + __le32 reserved; +}; + +struct mv_port_priv { + struct mv_crqb *crqb; + dma_addr_t crqb_dma; + struct mv_crpb *crpb; + dma_addr_t crpb_dma; + struct mv_sg *sg_tbl; + dma_addr_t sg_tbl_dma; + u32 pp_flags; +}; + +struct mv_port_signal { + u32 amps; + u32 pre; +}; + +struct mv_host_priv; +struct mv_hw_ops { + void (*phy_errata)(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port); + void (*enable_leds)(struct mv_host_priv *hpriv, void __iomem *mmio); + void (*read_preamp)(struct mv_host_priv *hpriv, int idx, + void __iomem *mmio); + int (*reset_hc)(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int n_hc); + void (*reset_flash)(struct mv_host_priv *hpriv, void __iomem *mmio); + void (*reset_bus)(struct pci_dev *pdev, void __iomem *mmio); +}; + +struct mv_host_priv { + u32 hp_flags; + struct mv_port_signal signal[8]; + const struct mv_hw_ops *ops; +}; + +static void mv_irq_clear(struct ata_port *ap); +static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in); +static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val); +static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in); +static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val); +static void mv_phy_reset(struct ata_port *ap); +static void __mv_phy_reset(struct ata_port *ap, int can_sleep); +static void mv_host_stop(struct ata_host *host); +static int mv_port_start(struct ata_port *ap); +static void mv_port_stop(struct ata_port *ap); +static void mv_qc_prep(struct ata_queued_cmd *qc); +static void mv_qc_prep_iie(struct ata_queued_cmd *qc); +static unsigned int mv_qc_issue(struct ata_queued_cmd *qc); +static irqreturn_t mv_interrupt(int irq, void *dev_instance, + struct pt_regs *regs); +static void mv_eng_timeout(struct ata_port *ap); +static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); + +static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port); +static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio); +static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx, + void __iomem *mmio); +static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int n_hc); +static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio); +static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio); + +static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port); +static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio); +static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, + void __iomem *mmio); +static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int n_hc); +static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio); +static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio); +static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port_no); +static void mv_stop_and_reset(struct ata_port *ap); + +static struct scsi_host_template mv_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = MV_USE_Q_DEPTH, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = MV_MAX_SG_CT / 2, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = MV_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations mv5_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .phy_reset = mv_phy_reset, + + .qc_prep = mv_qc_prep, + .qc_issue = mv_qc_issue, + .data_xfer = ata_mmio_data_xfer, + + .eng_timeout = mv_eng_timeout, + + .irq_handler = mv_interrupt, + .irq_clear = mv_irq_clear, + + .scr_read = mv5_scr_read, + .scr_write = mv5_scr_write, + + .port_start = mv_port_start, + .port_stop = mv_port_stop, + .host_stop = mv_host_stop, +}; + +static const struct ata_port_operations mv6_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .phy_reset = mv_phy_reset, + + .qc_prep = mv_qc_prep, + .qc_issue = mv_qc_issue, + .data_xfer = ata_mmio_data_xfer, + + .eng_timeout = mv_eng_timeout, + + .irq_handler = mv_interrupt, + .irq_clear = mv_irq_clear, + + .scr_read = mv_scr_read, + .scr_write = mv_scr_write, + + .port_start = mv_port_start, + .port_stop = mv_port_stop, + .host_stop = mv_host_stop, +}; + +static const struct ata_port_operations mv_iie_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .phy_reset = mv_phy_reset, + + .qc_prep = mv_qc_prep_iie, + .qc_issue = mv_qc_issue, + .data_xfer = ata_mmio_data_xfer, + + .eng_timeout = mv_eng_timeout, + + .irq_handler = mv_interrupt, + .irq_clear = mv_irq_clear, + + .scr_read = mv_scr_read, + .scr_write = mv_scr_write, + + .port_start = mv_port_start, + .port_stop = mv_port_stop, + .host_stop = mv_host_stop, +}; + +static const struct ata_port_info mv_port_info[] = { + { /* chip_504x */ + .sht = &mv_sht, + .flags = MV_COMMON_FLAGS, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &mv5_ops, + }, + { /* chip_508x */ + .sht = &mv_sht, + .flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC), + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &mv5_ops, + }, + { /* chip_5080 */ + .sht = &mv_sht, + .flags = (MV_COMMON_FLAGS | MV_FLAG_DUAL_HC), + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &mv5_ops, + }, + { /* chip_604x */ + .sht = &mv_sht, + .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS), + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &mv6_ops, + }, + { /* chip_608x */ + .sht = &mv_sht, + .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS | + MV_FLAG_DUAL_HC), + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &mv6_ops, + }, + { /* chip_6042 */ + .sht = &mv_sht, + .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS), + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &mv_iie_ops, + }, + { /* chip_7042 */ + .sht = &mv_sht, + .flags = (MV_COMMON_FLAGS | MV_6XXX_FLAGS | + MV_FLAG_DUAL_HC), + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &mv_iie_ops, + }, +}; + +static const struct pci_device_id mv_pci_tbl[] = { + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5040), 0, 0, chip_504x}, + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5041), 0, 0, chip_504x}, + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5080), 0, 0, chip_5080}, + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5081), 0, 0, chip_508x}, + + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6040), 0, 0, chip_604x}, + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6041), 0, 0, chip_604x}, + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6042), 0, 0, chip_6042}, + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6080), 0, 0, chip_608x}, + {PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x6081), 0, 0, chip_608x}, + + {PCI_DEVICE(PCI_VENDOR_ID_ADAPTEC2, 0x0241), 0, 0, chip_604x}, + {} /* terminate list */ +}; + +static struct pci_driver mv_pci_driver = { + .name = DRV_NAME, + .id_table = mv_pci_tbl, + .probe = mv_init_one, + .remove = ata_pci_remove_one, +}; + +static const struct mv_hw_ops mv5xxx_ops = { + .phy_errata = mv5_phy_errata, + .enable_leds = mv5_enable_leds, + .read_preamp = mv5_read_preamp, + .reset_hc = mv5_reset_hc, + .reset_flash = mv5_reset_flash, + .reset_bus = mv5_reset_bus, +}; + +static const struct mv_hw_ops mv6xxx_ops = { + .phy_errata = mv6_phy_errata, + .enable_leds = mv6_enable_leds, + .read_preamp = mv6_read_preamp, + .reset_hc = mv6_reset_hc, + .reset_flash = mv6_reset_flash, + .reset_bus = mv_reset_pci_bus, +}; + +/* + * module options + */ +static int msi; /* Use PCI msi; either zero (off, default) or non-zero */ + + +/* + * Functions + */ + +static inline void writelfl(unsigned long data, void __iomem *addr) +{ + writel(data, addr); + (void) readl(addr); /* flush to avoid PCI posted write */ +} + +static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc) +{ + return (base + MV_SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ)); +} + +static inline unsigned int mv_hc_from_port(unsigned int port) +{ + return port >> MV_PORT_HC_SHIFT; +} + +static inline unsigned int mv_hardport_from_port(unsigned int port) +{ + return port & MV_PORT_MASK; +} + +static inline void __iomem *mv_hc_base_from_port(void __iomem *base, + unsigned int port) +{ + return mv_hc_base(base, mv_hc_from_port(port)); +} + +static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port) +{ + return mv_hc_base_from_port(base, port) + + MV_SATAHC_ARBTR_REG_SZ + + (mv_hardport_from_port(port) * MV_PORT_REG_SZ); +} + +static inline void __iomem *mv_ap_base(struct ata_port *ap) +{ + return mv_port_base(ap->host->mmio_base, ap->port_no); +} + +static inline int mv_get_hc_count(unsigned long port_flags) +{ + return ((port_flags & MV_FLAG_DUAL_HC) ? 2 : 1); +} + +static void mv_irq_clear(struct ata_port *ap) +{ +} + +/** + * mv_start_dma - Enable eDMA engine + * @base: port base address + * @pp: port private data + * + * Verify the local cache of the eDMA state is accurate with a + * WARN_ON. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_start_dma(void __iomem *base, struct mv_port_priv *pp) +{ + if (!(MV_PP_FLAG_EDMA_EN & pp->pp_flags)) { + writelfl(EDMA_EN, base + EDMA_CMD_OFS); + pp->pp_flags |= MV_PP_FLAG_EDMA_EN; + } + WARN_ON(!(EDMA_EN & readl(base + EDMA_CMD_OFS))); +} + +/** + * mv_stop_dma - Disable eDMA engine + * @ap: ATA channel to manipulate + * + * Verify the local cache of the eDMA state is accurate with a + * WARN_ON. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_stop_dma(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + u32 reg; + int i; + + if (MV_PP_FLAG_EDMA_EN & pp->pp_flags) { + /* Disable EDMA if active. The disable bit auto clears. + */ + writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS); + pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + } else { + WARN_ON(EDMA_EN & readl(port_mmio + EDMA_CMD_OFS)); + } + + /* now properly wait for the eDMA to stop */ + for (i = 1000; i > 0; i--) { + reg = readl(port_mmio + EDMA_CMD_OFS); + if (!(EDMA_EN & reg)) { + break; + } + udelay(100); + } + + if (EDMA_EN & reg) { + ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n"); + /* FIXME: Consider doing a reset here to recover */ + } +} + +#ifdef ATA_DEBUG +static void mv_dump_mem(void __iomem *start, unsigned bytes) +{ + int b, w; + for (b = 0; b < bytes; ) { + DPRINTK("%p: ", start + b); + for (w = 0; b < bytes && w < 4; w++) { + printk("%08x ",readl(start + b)); + b += sizeof(u32); + } + printk("\n"); + } +} +#endif + +static void mv_dump_pci_cfg(struct pci_dev *pdev, unsigned bytes) +{ +#ifdef ATA_DEBUG + int b, w; + u32 dw; + for (b = 0; b < bytes; ) { + DPRINTK("%02x: ", b); + for (w = 0; b < bytes && w < 4; w++) { + (void) pci_read_config_dword(pdev,b,&dw); + printk("%08x ",dw); + b += sizeof(u32); + } + printk("\n"); + } +#endif +} +static void mv_dump_all_regs(void __iomem *mmio_base, int port, + struct pci_dev *pdev) +{ +#ifdef ATA_DEBUG + void __iomem *hc_base = mv_hc_base(mmio_base, + port >> MV_PORT_HC_SHIFT); + void __iomem *port_base; + int start_port, num_ports, p, start_hc, num_hcs, hc; + + if (0 > port) { + start_hc = start_port = 0; + num_ports = 8; /* shld be benign for 4 port devs */ + num_hcs = 2; + } else { + start_hc = port >> MV_PORT_HC_SHIFT; + start_port = port; + num_ports = num_hcs = 1; + } + DPRINTK("All registers for port(s) %u-%u:\n", start_port, + num_ports > 1 ? num_ports - 1 : start_port); + + if (NULL != pdev) { + DPRINTK("PCI config space regs:\n"); + mv_dump_pci_cfg(pdev, 0x68); + } + DPRINTK("PCI regs:\n"); + mv_dump_mem(mmio_base+0xc00, 0x3c); + mv_dump_mem(mmio_base+0xd00, 0x34); + mv_dump_mem(mmio_base+0xf00, 0x4); + mv_dump_mem(mmio_base+0x1d00, 0x6c); + for (hc = start_hc; hc < start_hc + num_hcs; hc++) { + hc_base = mv_hc_base(mmio_base, hc); + DPRINTK("HC regs (HC %i):\n", hc); + mv_dump_mem(hc_base, 0x1c); + } + for (p = start_port; p < start_port + num_ports; p++) { + port_base = mv_port_base(mmio_base, p); + DPRINTK("EDMA regs (port %i):\n",p); + mv_dump_mem(port_base, 0x54); + DPRINTK("SATA regs (port %i):\n",p); + mv_dump_mem(port_base+0x300, 0x60); + } +#endif +} + +static unsigned int mv_scr_offset(unsigned int sc_reg_in) +{ + unsigned int ofs; + + switch (sc_reg_in) { + case SCR_STATUS: + case SCR_CONTROL: + case SCR_ERROR: + ofs = SATA_STATUS_OFS + (sc_reg_in * sizeof(u32)); + break; + case SCR_ACTIVE: + ofs = SATA_ACTIVE_OFS; /* active is not with the others */ + break; + default: + ofs = 0xffffffffU; + break; + } + return ofs; +} + +static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in) +{ + unsigned int ofs = mv_scr_offset(sc_reg_in); + + if (0xffffffffU != ofs) { + return readl(mv_ap_base(ap) + ofs); + } else { + return (u32) ofs; + } +} + +static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val) +{ + unsigned int ofs = mv_scr_offset(sc_reg_in); + + if (0xffffffffU != ofs) { + writelfl(val, mv_ap_base(ap) + ofs); + } +} + +/** + * mv_host_stop - Host specific cleanup/stop routine. + * @host: host data structure + * + * Disable ints, cleanup host memory, call general purpose + * host_stop. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_host_stop(struct ata_host *host) +{ + struct mv_host_priv *hpriv = host->private_data; + struct pci_dev *pdev = to_pci_dev(host->dev); + + if (hpriv->hp_flags & MV_HP_FLAG_MSI) { + pci_disable_msi(pdev); + } else { + pci_intx(pdev, 0); + } + kfree(hpriv); + ata_host_stop(host); +} + +static inline void mv_priv_free(struct mv_port_priv *pp, struct device *dev) +{ + dma_free_coherent(dev, MV_PORT_PRIV_DMA_SZ, pp->crpb, pp->crpb_dma); +} + +static void mv_edma_cfg(struct mv_host_priv *hpriv, void __iomem *port_mmio) +{ + u32 cfg = readl(port_mmio + EDMA_CFG_OFS); + + /* set up non-NCQ EDMA configuration */ + cfg &= ~0x1f; /* clear queue depth */ + cfg &= ~EDMA_CFG_NCQ; /* clear NCQ mode */ + cfg &= ~(1 << 9); /* disable equeue */ + + if (IS_GEN_I(hpriv)) + cfg |= (1 << 8); /* enab config burst size mask */ + + else if (IS_GEN_II(hpriv)) + cfg |= EDMA_CFG_RD_BRST_EXT | EDMA_CFG_WR_BUFF_LEN; + + else if (IS_GEN_IIE(hpriv)) { + cfg |= (1 << 23); /* dis RX PM port mask */ + cfg &= ~(1 << 16); /* dis FIS-based switching (for now) */ + cfg &= ~(1 << 19); /* dis 128-entry queue (for now?) */ + cfg |= (1 << 18); /* enab early completion */ + cfg |= (1 << 17); /* enab host q cache */ + cfg |= (1 << 22); /* enab cutthrough */ + } + + writelfl(cfg, port_mmio + EDMA_CFG_OFS); +} + +/** + * mv_port_start - Port specific init/start routine. + * @ap: ATA channel to manipulate + * + * Allocate and point to DMA memory, init port private memory, + * zero indices. + * + * LOCKING: + * Inherited from caller. + */ +static int mv_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct mv_host_priv *hpriv = ap->host->private_data; + struct mv_port_priv *pp; + void __iomem *port_mmio = mv_ap_base(ap); + void *mem; + dma_addr_t mem_dma; + int rc = -ENOMEM; + + pp = kmalloc(sizeof(*pp), GFP_KERNEL); + if (!pp) + goto err_out; + memset(pp, 0, sizeof(*pp)); + + mem = dma_alloc_coherent(dev, MV_PORT_PRIV_DMA_SZ, &mem_dma, + GFP_KERNEL); + if (!mem) + goto err_out_pp; + memset(mem, 0, MV_PORT_PRIV_DMA_SZ); + + rc = ata_pad_alloc(ap, dev); + if (rc) + goto err_out_priv; + + /* First item in chunk of DMA memory: + * 32-slot command request table (CRQB), 32 bytes each in size + */ + pp->crqb = mem; + pp->crqb_dma = mem_dma; + mem += MV_CRQB_Q_SZ; + mem_dma += MV_CRQB_Q_SZ; + + /* Second item: + * 32-slot command response table (CRPB), 8 bytes each in size + */ + pp->crpb = mem; + pp->crpb_dma = mem_dma; + mem += MV_CRPB_Q_SZ; + mem_dma += MV_CRPB_Q_SZ; + + /* Third item: + * Table of scatter-gather descriptors (ePRD), 16 bytes each + */ + pp->sg_tbl = mem; + pp->sg_tbl_dma = mem_dma; + + mv_edma_cfg(hpriv, port_mmio); + + writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS); + writelfl(pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK, + port_mmio + EDMA_REQ_Q_IN_PTR_OFS); + + if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) + writelfl(pp->crqb_dma & 0xffffffff, + port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); + else + writelfl(0, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); + + writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS); + + if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) + writelfl(pp->crpb_dma & 0xffffffff, + port_mmio + EDMA_RSP_Q_IN_PTR_OFS); + else + writelfl(0, port_mmio + EDMA_RSP_Q_IN_PTR_OFS); + + writelfl(pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK, + port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); + + /* Don't turn on EDMA here...do it before DMA commands only. Else + * we'll be unable to send non-data, PIO, etc due to restricted access + * to shadow regs. + */ + ap->private_data = pp; + return 0; + +err_out_priv: + mv_priv_free(pp, dev); +err_out_pp: + kfree(pp); +err_out: + return rc; +} + +/** + * mv_port_stop - Port specific cleanup/stop routine. + * @ap: ATA channel to manipulate + * + * Stop DMA, cleanup port memory. + * + * LOCKING: + * This routine uses the host lock to protect the DMA stop. + */ +static void mv_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct mv_port_priv *pp = ap->private_data; + unsigned long flags; + + spin_lock_irqsave(&ap->host->lock, flags); + mv_stop_dma(ap); + spin_unlock_irqrestore(&ap->host->lock, flags); + + ap->private_data = NULL; + ata_pad_free(ap, dev); + mv_priv_free(pp, dev); + kfree(pp); +} + +/** + * mv_fill_sg - Fill out the Marvell ePRD (scatter gather) entries + * @qc: queued command whose SG list to source from + * + * Populate the SG list and mark the last entry. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_fill_sg(struct ata_queued_cmd *qc) +{ + struct mv_port_priv *pp = qc->ap->private_data; + unsigned int i = 0; + struct scatterlist *sg; + + ata_for_each_sg(sg, qc) { + dma_addr_t addr; + u32 sg_len, len, offset; + + addr = sg_dma_address(sg); + sg_len = sg_dma_len(sg); + + while (sg_len) { + offset = addr & MV_DMA_BOUNDARY; + len = sg_len; + if ((offset + sg_len) > 0x10000) + len = 0x10000 - offset; + + pp->sg_tbl[i].addr = cpu_to_le32(addr & 0xffffffff); + pp->sg_tbl[i].addr_hi = cpu_to_le32((addr >> 16) >> 16); + pp->sg_tbl[i].flags_size = cpu_to_le32(len & 0xffff); + + sg_len -= len; + addr += len; + + if (!sg_len && ata_sg_is_last(sg, qc)) + pp->sg_tbl[i].flags_size |= cpu_to_le32(EPRD_FLAG_END_OF_TBL); + + i++; + } + } +} + +static inline unsigned mv_inc_q_index(unsigned index) +{ + return (index + 1) & MV_MAX_Q_DEPTH_MASK; +} + +static inline void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last) +{ + u16 tmp = data | (addr << CRQB_CMD_ADDR_SHIFT) | CRQB_CMD_CS | + (last ? CRQB_CMD_LAST : 0); + *cmdw = cpu_to_le16(tmp); +} + +/** + * mv_qc_prep - Host specific command preparation. + * @qc: queued command to prepare + * + * This routine simply redirects to the general purpose routine + * if command is not DMA. Else, it handles prep of the CRQB + * (command request block), does some sanity checking, and calls + * the SG load routine. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_qc_prep(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct mv_port_priv *pp = ap->private_data; + __le16 *cw; + struct ata_taskfile *tf; + u16 flags = 0; + unsigned in_index; + + if (ATA_PROT_DMA != qc->tf.protocol) + return; + + /* Fill in command request block + */ + if (!(qc->tf.flags & ATA_TFLAG_WRITE)) + flags |= CRQB_FLAG_READ; + WARN_ON(MV_MAX_Q_DEPTH <= qc->tag); + flags |= qc->tag << CRQB_TAG_SHIFT; + + /* get current queue index from hardware */ + in_index = (readl(mv_ap_base(ap) + EDMA_REQ_Q_IN_PTR_OFS) + >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + + pp->crqb[in_index].sg_addr = + cpu_to_le32(pp->sg_tbl_dma & 0xffffffff); + pp->crqb[in_index].sg_addr_hi = + cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16); + pp->crqb[in_index].ctrl_flags = cpu_to_le16(flags); + + cw = &pp->crqb[in_index].ata_cmd[0]; + tf = &qc->tf; + + /* Sadly, the CRQB cannot accomodate all registers--there are + * only 11 bytes...so we must pick and choose required + * registers based on the command. So, we drop feature and + * hob_feature for [RW] DMA commands, but they are needed for + * NCQ. NCQ will drop hob_nsect. + */ + switch (tf->command) { + case ATA_CMD_READ: + case ATA_CMD_READ_EXT: + case ATA_CMD_WRITE: + case ATA_CMD_WRITE_EXT: + case ATA_CMD_WRITE_FUA_EXT: + mv_crqb_pack_cmd(cw++, tf->hob_nsect, ATA_REG_NSECT, 0); + break; +#ifdef LIBATA_NCQ /* FIXME: remove this line when NCQ added */ + case ATA_CMD_FPDMA_READ: + case ATA_CMD_FPDMA_WRITE: + mv_crqb_pack_cmd(cw++, tf->hob_feature, ATA_REG_FEATURE, 0); + mv_crqb_pack_cmd(cw++, tf->feature, ATA_REG_FEATURE, 0); + break; +#endif /* FIXME: remove this line when NCQ added */ + default: + /* The only other commands EDMA supports in non-queued and + * non-NCQ mode are: [RW] STREAM DMA and W DMA FUA EXT, none + * of which are defined/used by Linux. If we get here, this + * driver needs work. + * + * FIXME: modify libata to give qc_prep a return value and + * return error here. + */ + BUG_ON(tf->command); + break; + } + mv_crqb_pack_cmd(cw++, tf->nsect, ATA_REG_NSECT, 0); + mv_crqb_pack_cmd(cw++, tf->hob_lbal, ATA_REG_LBAL, 0); + mv_crqb_pack_cmd(cw++, tf->lbal, ATA_REG_LBAL, 0); + mv_crqb_pack_cmd(cw++, tf->hob_lbam, ATA_REG_LBAM, 0); + mv_crqb_pack_cmd(cw++, tf->lbam, ATA_REG_LBAM, 0); + mv_crqb_pack_cmd(cw++, tf->hob_lbah, ATA_REG_LBAH, 0); + mv_crqb_pack_cmd(cw++, tf->lbah, ATA_REG_LBAH, 0); + mv_crqb_pack_cmd(cw++, tf->device, ATA_REG_DEVICE, 0); + mv_crqb_pack_cmd(cw++, tf->command, ATA_REG_CMD, 1); /* last */ + + if (!(qc->flags & ATA_QCFLAG_DMAMAP)) + return; + mv_fill_sg(qc); +} + +/** + * mv_qc_prep_iie - Host specific command preparation. + * @qc: queued command to prepare + * + * This routine simply redirects to the general purpose routine + * if command is not DMA. Else, it handles prep of the CRQB + * (command request block), does some sanity checking, and calls + * the SG load routine. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_qc_prep_iie(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct mv_port_priv *pp = ap->private_data; + struct mv_crqb_iie *crqb; + struct ata_taskfile *tf; + unsigned in_index; + u32 flags = 0; + + if (ATA_PROT_DMA != qc->tf.protocol) + return; + + /* Fill in Gen IIE command request block + */ + if (!(qc->tf.flags & ATA_TFLAG_WRITE)) + flags |= CRQB_FLAG_READ; + + WARN_ON(MV_MAX_Q_DEPTH <= qc->tag); + flags |= qc->tag << CRQB_TAG_SHIFT; + + /* get current queue index from hardware */ + in_index = (readl(mv_ap_base(ap) + EDMA_REQ_Q_IN_PTR_OFS) + >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + + crqb = (struct mv_crqb_iie *) &pp->crqb[in_index]; + crqb->addr = cpu_to_le32(pp->sg_tbl_dma & 0xffffffff); + crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma >> 16) >> 16); + crqb->flags = cpu_to_le32(flags); + + tf = &qc->tf; + crqb->ata_cmd[0] = cpu_to_le32( + (tf->command << 16) | + (tf->feature << 24) + ); + crqb->ata_cmd[1] = cpu_to_le32( + (tf->lbal << 0) | + (tf->lbam << 8) | + (tf->lbah << 16) | + (tf->device << 24) + ); + crqb->ata_cmd[2] = cpu_to_le32( + (tf->hob_lbal << 0) | + (tf->hob_lbam << 8) | + (tf->hob_lbah << 16) | + (tf->hob_feature << 24) + ); + crqb->ata_cmd[3] = cpu_to_le32( + (tf->nsect << 0) | + (tf->hob_nsect << 8) + ); + + if (!(qc->flags & ATA_QCFLAG_DMAMAP)) + return; + mv_fill_sg(qc); +} + +/** + * mv_qc_issue - Initiate a command to the host + * @qc: queued command to start + * + * This routine simply redirects to the general purpose routine + * if command is not DMA. Else, it sanity checks our local + * caches of the request producer/consumer indices then enables + * DMA and bumps the request producer index. + * + * LOCKING: + * Inherited from caller. + */ +static unsigned int mv_qc_issue(struct ata_queued_cmd *qc) +{ + void __iomem *port_mmio = mv_ap_base(qc->ap); + struct mv_port_priv *pp = qc->ap->private_data; + unsigned in_index; + u32 in_ptr; + + if (ATA_PROT_DMA != qc->tf.protocol) { + /* We're about to send a non-EDMA capable command to the + * port. Turn off EDMA so there won't be problems accessing + * shadow block, etc registers. + */ + mv_stop_dma(qc->ap); + return ata_qc_issue_prot(qc); + } + + in_ptr = readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS); + in_index = (in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + + /* until we do queuing, the queue should be empty at this point */ + WARN_ON(in_index != ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) + >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK)); + + in_index = mv_inc_q_index(in_index); /* now incr producer index */ + + mv_start_dma(port_mmio, pp); + + /* and write the request in pointer to kick the EDMA to life */ + in_ptr &= EDMA_REQ_Q_BASE_LO_MASK; + in_ptr |= in_index << EDMA_REQ_Q_PTR_SHIFT; + writelfl(in_ptr, port_mmio + EDMA_REQ_Q_IN_PTR_OFS); + + return 0; +} + +/** + * mv_get_crpb_status - get status from most recently completed cmd + * @ap: ATA channel to manipulate + * + * This routine is for use when the port is in DMA mode, when it + * will be using the CRPB (command response block) method of + * returning command completion information. We check indices + * are good, grab status, and bump the response consumer index to + * prove that we're up to date. + * + * LOCKING: + * Inherited from caller. + */ +static u8 mv_get_crpb_status(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + unsigned out_index; + u32 out_ptr; + u8 ata_status; + + out_ptr = readl(port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); + out_index = (out_ptr >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + + ata_status = le16_to_cpu(pp->crpb[out_index].flags) + >> CRPB_FLAG_STATUS_SHIFT; + + /* increment our consumer index... */ + out_index = mv_inc_q_index(out_index); + + /* and, until we do NCQ, there should only be 1 CRPB waiting */ + WARN_ON(out_index != ((readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS) + >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK)); + + /* write out our inc'd consumer index so EDMA knows we're caught up */ + out_ptr &= EDMA_RSP_Q_BASE_LO_MASK; + out_ptr |= out_index << EDMA_RSP_Q_PTR_SHIFT; + writelfl(out_ptr, port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); + + /* Return ATA status register for completed CRPB */ + return ata_status; +} + +/** + * mv_err_intr - Handle error interrupts on the port + * @ap: ATA channel to manipulate + * @reset_allowed: bool: 0 == don't trigger from reset here + * + * In most cases, just clear the interrupt and move on. However, + * some cases require an eDMA reset, which is done right before + * the COMRESET in mv_phy_reset(). The SERR case requires a + * clear of pending errors in the SATA SERROR register. Finally, + * if the port disabled DMA, update our cached copy to match. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_err_intr(struct ata_port *ap, int reset_allowed) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 edma_err_cause, serr = 0; + + edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + + if (EDMA_ERR_SERR & edma_err_cause) { + sata_scr_read(ap, SCR_ERROR, &serr); + sata_scr_write_flush(ap, SCR_ERROR, serr); + } + if (EDMA_ERR_SELF_DIS & edma_err_cause) { + struct mv_port_priv *pp = ap->private_data; + pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + } + DPRINTK(KERN_ERR "ata%u: port error; EDMA err cause: 0x%08x " + "SERR: 0x%08x\n", ap->id, edma_err_cause, serr); + + /* Clear EDMA now that SERR cleanup done */ + writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + + /* check for fatal here and recover if needed */ + if (reset_allowed && (EDMA_ERR_FATAL & edma_err_cause)) + mv_stop_and_reset(ap); +} + +/** + * mv_host_intr - Handle all interrupts on the given host controller + * @host: host specific structure + * @relevant: port error bits relevant to this host controller + * @hc: which host controller we're to look at + * + * Read then write clear the HC interrupt status then walk each + * port connected to the HC and see if it needs servicing. Port + * success ints are reported in the HC interrupt status reg, the + * port error ints are reported in the higher level main + * interrupt status register and thus are passed in via the + * 'relevant' argument. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc) +{ + void __iomem *mmio = host->mmio_base; + void __iomem *hc_mmio = mv_hc_base(mmio, hc); + struct ata_queued_cmd *qc; + u32 hc_irq_cause; + int shift, port, port0, hard_port, handled; + unsigned int err_mask; + + if (hc == 0) { + port0 = 0; + } else { + port0 = MV_PORTS_PER_HC; + } + + /* we'll need the HC success int register in most cases */ + hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS); + if (hc_irq_cause) { + writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS); + } + + VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n", + hc,relevant,hc_irq_cause); + + for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) { + u8 ata_status = 0; + struct ata_port *ap = host->ports[port]; + struct mv_port_priv *pp = ap->private_data; + + hard_port = mv_hardport_from_port(port); /* range 0..3 */ + handled = 0; /* ensure ata_status is set if handled++ */ + + /* Note that DEV_IRQ might happen spuriously during EDMA, + * and should be ignored in such cases. + * The cause of this is still under investigation. + */ + if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) { + /* EDMA: check for response queue interrupt */ + if ((CRPB_DMA_DONE << hard_port) & hc_irq_cause) { + ata_status = mv_get_crpb_status(ap); + handled = 1; + } + } else { + /* PIO: check for device (drive) interrupt */ + if ((DEV_IRQ << hard_port) & hc_irq_cause) { + ata_status = readb((void __iomem *) + ap->ioaddr.status_addr); + handled = 1; + /* ignore spurious intr if drive still BUSY */ + if (ata_status & ATA_BUSY) { + ata_status = 0; + handled = 0; + } + } + } + + if (ap && (ap->flags & ATA_FLAG_DISABLED)) + continue; + + err_mask = ac_err_mask(ata_status); + + shift = port << 1; /* (port * 2) */ + if (port >= MV_PORTS_PER_HC) { + shift++; /* skip bit 8 in the HC Main IRQ reg */ + } + if ((PORT0_ERR << shift) & relevant) { + mv_err_intr(ap, 1); + err_mask |= AC_ERR_OTHER; + handled = 1; + } + + if (handled) { + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (qc->flags & ATA_QCFLAG_ACTIVE)) { + VPRINTK("port %u IRQ found for qc, " + "ata_status 0x%x\n", port,ata_status); + /* mark qc status appropriately */ + if (!(qc->tf.flags & ATA_TFLAG_POLLING)) { + qc->err_mask |= err_mask; + ata_qc_complete(qc); + } + } + } + } + VPRINTK("EXIT\n"); +} + +/** + * mv_interrupt - + * @irq: unused + * @dev_instance: private data; in this case the host structure + * @regs: unused + * + * Read the read only register to determine if any host + * controllers have pending interrupts. If so, call lower level + * routine to handle. Also check for PCI errors which are only + * reported here. + * + * LOCKING: + * This routine holds the host lock while processing pending + * interrupts. + */ +static irqreturn_t mv_interrupt(int irq, void *dev_instance, + struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + unsigned int hc, handled = 0, n_hcs; + void __iomem *mmio = host->mmio_base; + struct mv_host_priv *hpriv; + u32 irq_stat; + + irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS); + + /* check the cases where we either have nothing pending or have read + * a bogus register value which can indicate HW removal or PCI fault + */ + if (!irq_stat || (0xffffffffU == irq_stat)) { + return IRQ_NONE; + } + + n_hcs = mv_get_hc_count(host->ports[0]->flags); + spin_lock(&host->lock); + + for (hc = 0; hc < n_hcs; hc++) { + u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT)); + if (relevant) { + mv_host_intr(host, relevant, hc); + handled++; + } + } + + hpriv = host->private_data; + if (IS_60XX(hpriv)) { + /* deal with the interrupt coalescing bits */ + if (irq_stat & (TRAN_LO_DONE | TRAN_HI_DONE | PORTS_0_7_COAL_DONE)) { + writelfl(0, mmio + MV_IRQ_COAL_CAUSE_LO); + writelfl(0, mmio + MV_IRQ_COAL_CAUSE_HI); + writelfl(0, mmio + MV_IRQ_COAL_CAUSE); + } + } + + if (PCI_ERR & irq_stat) { + printk(KERN_ERR DRV_NAME ": PCI ERROR; PCI IRQ cause=0x%08x\n", + readl(mmio + PCI_IRQ_CAUSE_OFS)); + + DPRINTK("All regs @ PCI error\n"); + mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev)); + + writelfl(0, mmio + PCI_IRQ_CAUSE_OFS); + handled++; + } + spin_unlock(&host->lock); + + return IRQ_RETVAL(handled); +} + +static void __iomem *mv5_phy_base(void __iomem *mmio, unsigned int port) +{ + void __iomem *hc_mmio = mv_hc_base_from_port(mmio, port); + unsigned long ofs = (mv_hardport_from_port(port) + 1) * 0x100UL; + + return hc_mmio + ofs; +} + +static unsigned int mv5_scr_offset(unsigned int sc_reg_in) +{ + unsigned int ofs; + + switch (sc_reg_in) { + case SCR_STATUS: + case SCR_ERROR: + case SCR_CONTROL: + ofs = sc_reg_in * sizeof(u32); + break; + default: + ofs = 0xffffffffU; + break; + } + return ofs; +} + +static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in) +{ + void __iomem *mmio = mv5_phy_base(ap->host->mmio_base, ap->port_no); + unsigned int ofs = mv5_scr_offset(sc_reg_in); + + if (ofs != 0xffffffffU) + return readl(mmio + ofs); + else + return (u32) ofs; +} + +static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val) +{ + void __iomem *mmio = mv5_phy_base(ap->host->mmio_base, ap->port_no); + unsigned int ofs = mv5_scr_offset(sc_reg_in); + + if (ofs != 0xffffffffU) + writelfl(val, mmio + ofs); +} + +static void mv5_reset_bus(struct pci_dev *pdev, void __iomem *mmio) +{ + u8 rev_id; + int early_5080; + + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id); + + early_5080 = (pdev->device == 0x5080) && (rev_id == 0); + + if (!early_5080) { + u32 tmp = readl(mmio + MV_PCI_EXP_ROM_BAR_CTL); + tmp |= (1 << 0); + writel(tmp, mmio + MV_PCI_EXP_ROM_BAR_CTL); + } + + mv_reset_pci_bus(pdev, mmio); +} + +static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) +{ + writel(0x0fcfffff, mmio + MV_FLASH_CTL); +} + +static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx, + void __iomem *mmio) +{ + void __iomem *phy_mmio = mv5_phy_base(mmio, idx); + u32 tmp; + + tmp = readl(phy_mmio + MV5_PHY_MODE); + + hpriv->signal[idx].pre = tmp & 0x1800; /* bits 12:11 */ + hpriv->signal[idx].amps = tmp & 0xe0; /* bits 7:5 */ +} + +static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) +{ + u32 tmp; + + writel(0, mmio + MV_GPIO_PORT_CTL); + + /* FIXME: handle MV_HP_ERRATA_50XXB2 errata */ + + tmp = readl(mmio + MV_PCI_EXP_ROM_BAR_CTL); + tmp |= ~(1 << 0); + writel(tmp, mmio + MV_PCI_EXP_ROM_BAR_CTL); +} + +static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port) +{ + void __iomem *phy_mmio = mv5_phy_base(mmio, port); + const u32 mask = (1<<12) | (1<<11) | (1<<7) | (1<<6) | (1<<5); + u32 tmp; + int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0); + + if (fix_apm_sq) { + tmp = readl(phy_mmio + MV5_LT_MODE); + tmp |= (1 << 19); + writel(tmp, phy_mmio + MV5_LT_MODE); + + tmp = readl(phy_mmio + MV5_PHY_CTL); + tmp &= ~0x3; + tmp |= 0x1; + writel(tmp, phy_mmio + MV5_PHY_CTL); + } + + tmp = readl(phy_mmio + MV5_PHY_MODE); + tmp &= ~mask; + tmp |= hpriv->signal[port].pre; + tmp |= hpriv->signal[port].amps; + writel(tmp, phy_mmio + MV5_PHY_MODE); +} + + +#undef ZERO +#define ZERO(reg) writel(0, port_mmio + (reg)) +static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port) +{ + void __iomem *port_mmio = mv_port_base(mmio, port); + + writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS); + + mv_channel_reset(hpriv, mmio, port); + + ZERO(0x028); /* command */ + writel(0x11f, port_mmio + EDMA_CFG_OFS); + ZERO(0x004); /* timer */ + ZERO(0x008); /* irq err cause */ + ZERO(0x00c); /* irq err mask */ + ZERO(0x010); /* rq bah */ + ZERO(0x014); /* rq inp */ + ZERO(0x018); /* rq outp */ + ZERO(0x01c); /* respq bah */ + ZERO(0x024); /* respq outp */ + ZERO(0x020); /* respq inp */ + ZERO(0x02c); /* test control */ + writel(0xbc, port_mmio + EDMA_IORDY_TMOUT); +} +#undef ZERO + +#define ZERO(reg) writel(0, hc_mmio + (reg)) +static void mv5_reset_one_hc(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int hc) +{ + void __iomem *hc_mmio = mv_hc_base(mmio, hc); + u32 tmp; + + ZERO(0x00c); + ZERO(0x010); + ZERO(0x014); + ZERO(0x018); + + tmp = readl(hc_mmio + 0x20); + tmp &= 0x1c1c1c1c; + tmp |= 0x03030303; + writel(tmp, hc_mmio + 0x20); +} +#undef ZERO + +static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int n_hc) +{ + unsigned int hc, port; + + for (hc = 0; hc < n_hc; hc++) { + for (port = 0; port < MV_PORTS_PER_HC; port++) + mv5_reset_hc_port(hpriv, mmio, + (hc * MV_PORTS_PER_HC) + port); + + mv5_reset_one_hc(hpriv, mmio, hc); + } + + return 0; +} + +#undef ZERO +#define ZERO(reg) writel(0, mmio + (reg)) +static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio) +{ + u32 tmp; + + tmp = readl(mmio + MV_PCI_MODE); + tmp &= 0xff00ffff; + writel(tmp, mmio + MV_PCI_MODE); + + ZERO(MV_PCI_DISC_TIMER); + ZERO(MV_PCI_MSI_TRIGGER); + writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT); + ZERO(HC_MAIN_IRQ_MASK_OFS); + ZERO(MV_PCI_SERR_MASK); + ZERO(PCI_IRQ_CAUSE_OFS); + ZERO(PCI_IRQ_MASK_OFS); + ZERO(MV_PCI_ERR_LOW_ADDRESS); + ZERO(MV_PCI_ERR_HIGH_ADDRESS); + ZERO(MV_PCI_ERR_ATTRIBUTE); + ZERO(MV_PCI_ERR_COMMAND); +} +#undef ZERO + +static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) +{ + u32 tmp; + + mv5_reset_flash(hpriv, mmio); + + tmp = readl(mmio + MV_GPIO_PORT_CTL); + tmp &= 0x3; + tmp |= (1 << 5) | (1 << 6); + writel(tmp, mmio + MV_GPIO_PORT_CTL); +} + +/** + * mv6_reset_hc - Perform the 6xxx global soft reset + * @mmio: base address of the HBA + * + * This routine only applies to 6xxx parts. + * + * LOCKING: + * Inherited from caller. + */ +static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int n_hc) +{ + void __iomem *reg = mmio + PCI_MAIN_CMD_STS_OFS; + int i, rc = 0; + u32 t; + + /* Following procedure defined in PCI "main command and status + * register" table. + */ + t = readl(reg); + writel(t | STOP_PCI_MASTER, reg); + + for (i = 0; i < 1000; i++) { + udelay(1); + t = readl(reg); + if (PCI_MASTER_EMPTY & t) { + break; + } + } + if (!(PCI_MASTER_EMPTY & t)) { + printk(KERN_ERR DRV_NAME ": PCI master won't flush\n"); + rc = 1; + goto done; + } + + /* set reset */ + i = 5; + do { + writel(t | GLOB_SFT_RST, reg); + t = readl(reg); + udelay(1); + } while (!(GLOB_SFT_RST & t) && (i-- > 0)); + + if (!(GLOB_SFT_RST & t)) { + printk(KERN_ERR DRV_NAME ": can't set global reset\n"); + rc = 1; + goto done; + } + + /* clear reset and *reenable the PCI master* (not mentioned in spec) */ + i = 5; + do { + writel(t & ~(GLOB_SFT_RST | STOP_PCI_MASTER), reg); + t = readl(reg); + udelay(1); + } while ((GLOB_SFT_RST & t) && (i-- > 0)); + + if (GLOB_SFT_RST & t) { + printk(KERN_ERR DRV_NAME ": can't clear global reset\n"); + rc = 1; + } +done: + return rc; +} + +static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, + void __iomem *mmio) +{ + void __iomem *port_mmio; + u32 tmp; + + tmp = readl(mmio + MV_RESET_CFG); + if ((tmp & (1 << 0)) == 0) { + hpriv->signal[idx].amps = 0x7 << 8; + hpriv->signal[idx].pre = 0x1 << 5; + return; + } + + port_mmio = mv_port_base(mmio, idx); + tmp = readl(port_mmio + PHY_MODE2); + + hpriv->signal[idx].amps = tmp & 0x700; /* bits 10:8 */ + hpriv->signal[idx].pre = tmp & 0xe0; /* bits 7:5 */ +} + +static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) +{ + writel(0x00000060, mmio + MV_GPIO_PORT_CTL); +} + +static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port) +{ + void __iomem *port_mmio = mv_port_base(mmio, port); + + u32 hp_flags = hpriv->hp_flags; + int fix_phy_mode2 = + hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); + int fix_phy_mode4 = + hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); + u32 m2, tmp; + + if (fix_phy_mode2) { + m2 = readl(port_mmio + PHY_MODE2); + m2 &= ~(1 << 16); + m2 |= (1 << 31); + writel(m2, port_mmio + PHY_MODE2); + + udelay(200); + + m2 = readl(port_mmio + PHY_MODE2); + m2 &= ~((1 << 16) | (1 << 31)); + writel(m2, port_mmio + PHY_MODE2); + + udelay(200); + } + + /* who knows what this magic does */ + tmp = readl(port_mmio + PHY_MODE3); + tmp &= ~0x7F800000; + tmp |= 0x2A800000; + writel(tmp, port_mmio + PHY_MODE3); + + if (fix_phy_mode4) { + u32 m4; + + m4 = readl(port_mmio + PHY_MODE4); + + if (hp_flags & MV_HP_ERRATA_60X1B2) + tmp = readl(port_mmio + 0x310); + + m4 = (m4 & ~(1 << 1)) | (1 << 0); + + writel(m4, port_mmio + PHY_MODE4); + + if (hp_flags & MV_HP_ERRATA_60X1B2) + writel(tmp, port_mmio + 0x310); + } + + /* Revert values of pre-emphasis and signal amps to the saved ones */ + m2 = readl(port_mmio + PHY_MODE2); + + m2 &= ~MV_M2_PREAMP_MASK; + m2 |= hpriv->signal[port].amps; + m2 |= hpriv->signal[port].pre; + m2 &= ~(1 << 16); + + /* according to mvSata 3.6.1, some IIE values are fixed */ + if (IS_GEN_IIE(hpriv)) { + m2 &= ~0xC30FF01F; + m2 |= 0x0000900F; + } + + writel(m2, port_mmio + PHY_MODE2); +} + +static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio, + unsigned int port_no) +{ + void __iomem *port_mmio = mv_port_base(mmio, port_no); + + writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS); + + if (IS_60XX(hpriv)) { + u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL); + ifctl |= (1 << 7); /* enable gen2i speed */ + ifctl = (ifctl & 0xfff) | 0x9b1000; /* from chip spec */ + writelfl(ifctl, port_mmio + SATA_INTERFACE_CTL); + } + + udelay(25); /* allow reset propagation */ + + /* Spec never mentions clearing the bit. Marvell's driver does + * clear the bit, however. + */ + writelfl(0, port_mmio + EDMA_CMD_OFS); + + hpriv->ops->phy_errata(hpriv, mmio, port_no); + + if (IS_50XX(hpriv)) + mdelay(1); +} + +static void mv_stop_and_reset(struct ata_port *ap) +{ + struct mv_host_priv *hpriv = ap->host->private_data; + void __iomem *mmio = ap->host->mmio_base; + + mv_stop_dma(ap); + + mv_channel_reset(hpriv, mmio, ap->port_no); + + __mv_phy_reset(ap, 0); +} + +static inline void __msleep(unsigned int msec, int can_sleep) +{ + if (can_sleep) + msleep(msec); + else + mdelay(msec); +} + +/** + * __mv_phy_reset - Perform eDMA reset followed by COMRESET + * @ap: ATA channel to manipulate + * + * Part of this is taken from __sata_phy_reset and modified to + * not sleep since this routine gets called from interrupt level. + * + * LOCKING: + * Inherited from caller. This is coded to safe to call at + * interrupt level, i.e. it does not sleep. + */ +static void __mv_phy_reset(struct ata_port *ap, int can_sleep) +{ + struct mv_port_priv *pp = ap->private_data; + struct mv_host_priv *hpriv = ap->host->private_data; + void __iomem *port_mmio = mv_ap_base(ap); + struct ata_taskfile tf; + struct ata_device *dev = &ap->device[0]; + unsigned long timeout; + int retry = 5; + u32 sstatus; + + VPRINTK("ENTER, port %u, mmio 0x%p\n", ap->port_no, port_mmio); + + DPRINTK("S-regs after ATA_RST: SStat 0x%08x SErr 0x%08x " + "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS), + mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL)); + + /* Issue COMRESET via SControl */ +comreset_retry: + sata_scr_write_flush(ap, SCR_CONTROL, 0x301); + __msleep(1, can_sleep); + + sata_scr_write_flush(ap, SCR_CONTROL, 0x300); + __msleep(20, can_sleep); + + timeout = jiffies + msecs_to_jiffies(200); + do { + sata_scr_read(ap, SCR_STATUS, &sstatus); + if (((sstatus & 0x3) == 3) || ((sstatus & 0x3) == 0)) + break; + + __msleep(1, can_sleep); + } while (time_before(jiffies, timeout)); + + /* work around errata */ + if (IS_60XX(hpriv) && + (sstatus != 0x0) && (sstatus != 0x113) && (sstatus != 0x123) && + (retry-- > 0)) + goto comreset_retry; + + DPRINTK("S-regs after PHY wake: SStat 0x%08x SErr 0x%08x " + "SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS), + mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL)); + + if (ata_port_online(ap)) { + ata_port_probe(ap); + } else { + sata_scr_read(ap, SCR_STATUS, &sstatus); + ata_port_printk(ap, KERN_INFO, + "no device found (phy stat %08x)\n", sstatus); + ata_port_disable(ap); + return; + } + ap->cbl = ATA_CBL_SATA; + + /* even after SStatus reflects that device is ready, + * it seems to take a while for link to be fully + * established (and thus Status no longer 0x80/0x7F), + * so we poll a bit for that, here. + */ + retry = 20; + while (1) { + u8 drv_stat = ata_check_status(ap); + if ((drv_stat != 0x80) && (drv_stat != 0x7f)) + break; + __msleep(500, can_sleep); + if (retry-- <= 0) + break; + } + + tf.lbah = readb((void __iomem *) ap->ioaddr.lbah_addr); + tf.lbam = readb((void __iomem *) ap->ioaddr.lbam_addr); + tf.lbal = readb((void __iomem *) ap->ioaddr.lbal_addr); + tf.nsect = readb((void __iomem *) ap->ioaddr.nsect_addr); + + dev->class = ata_dev_classify(&tf); + if (!ata_dev_enabled(dev)) { + VPRINTK("Port disabled post-sig: No device present.\n"); + ata_port_disable(ap); + } + + writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + + pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + + VPRINTK("EXIT\n"); +} + +static void mv_phy_reset(struct ata_port *ap) +{ + __mv_phy_reset(ap, 1); +} + +/** + * mv_eng_timeout - Routine called by libata when SCSI times out I/O + * @ap: ATA channel to manipulate + * + * Intent is to clear all pending error conditions, reset the + * chip/bus, fail the command, and move on. + * + * LOCKING: + * This routine holds the host lock while failing the command. + */ +static void mv_eng_timeout(struct ata_port *ap) +{ + struct ata_queued_cmd *qc; + unsigned long flags; + + ata_port_printk(ap, KERN_ERR, "Entering mv_eng_timeout\n"); + DPRINTK("All regs @ start of eng_timeout\n"); + mv_dump_all_regs(ap->host->mmio_base, ap->port_no, + to_pci_dev(ap->host->dev)); + + qc = ata_qc_from_tag(ap, ap->active_tag); + printk(KERN_ERR "mmio_base %p ap %p qc %p scsi_cmnd %p &cmnd %p\n", + ap->host->mmio_base, ap, qc, qc->scsicmd, &qc->scsicmd->cmnd); + + spin_lock_irqsave(&ap->host->lock, flags); + mv_err_intr(ap, 0); + mv_stop_and_reset(ap); + spin_unlock_irqrestore(&ap->host->lock, flags); + + WARN_ON(!(qc->flags & ATA_QCFLAG_ACTIVE)); + if (qc->flags & ATA_QCFLAG_ACTIVE) { + qc->err_mask |= AC_ERR_TIMEOUT; + ata_eh_qc_complete(qc); + } +} + +/** + * mv_port_init - Perform some early initialization on a single port. + * @port: libata data structure storing shadow register addresses + * @port_mmio: base address of the port + * + * Initialize shadow register mmio addresses, clear outstanding + * interrupts on the port, and unmask interrupts for the future + * start of the port. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio) +{ + unsigned long shd_base = (unsigned long) port_mmio + SHD_BLK_OFS; + unsigned serr_ofs; + + /* PIO related setup + */ + port->data_addr = shd_base + (sizeof(u32) * ATA_REG_DATA); + port->error_addr = + port->feature_addr = shd_base + (sizeof(u32) * ATA_REG_ERR); + port->nsect_addr = shd_base + (sizeof(u32) * ATA_REG_NSECT); + port->lbal_addr = shd_base + (sizeof(u32) * ATA_REG_LBAL); + port->lbam_addr = shd_base + (sizeof(u32) * ATA_REG_LBAM); + port->lbah_addr = shd_base + (sizeof(u32) * ATA_REG_LBAH); + port->device_addr = shd_base + (sizeof(u32) * ATA_REG_DEVICE); + port->status_addr = + port->command_addr = shd_base + (sizeof(u32) * ATA_REG_STATUS); + /* special case: control/altstatus doesn't have ATA_REG_ address */ + port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST_OFS; + + /* unused: */ + port->cmd_addr = port->bmdma_addr = port->scr_addr = 0; + + /* Clear any currently outstanding port interrupt conditions */ + serr_ofs = mv_scr_offset(SCR_ERROR); + writelfl(readl(port_mmio + serr_ofs), port_mmio + serr_ofs); + writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + + /* unmask all EDMA error interrupts */ + writelfl(~0, port_mmio + EDMA_ERR_IRQ_MASK_OFS); + + VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n", + readl(port_mmio + EDMA_CFG_OFS), + readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS), + readl(port_mmio + EDMA_ERR_IRQ_MASK_OFS)); +} + +static int mv_chip_id(struct pci_dev *pdev, struct mv_host_priv *hpriv, + unsigned int board_idx) +{ + u8 rev_id; + u32 hp_flags = hpriv->hp_flags; + + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id); + + switch(board_idx) { + case chip_5080: + hpriv->ops = &mv5xxx_ops; + hp_flags |= MV_HP_50XX; + + switch (rev_id) { + case 0x1: + hp_flags |= MV_HP_ERRATA_50XXB0; + break; + case 0x3: + hp_flags |= MV_HP_ERRATA_50XXB2; + break; + default: + dev_printk(KERN_WARNING, &pdev->dev, + "Applying 50XXB2 workarounds to unknown rev\n"); + hp_flags |= MV_HP_ERRATA_50XXB2; + break; + } + break; + + case chip_504x: + case chip_508x: + hpriv->ops = &mv5xxx_ops; + hp_flags |= MV_HP_50XX; + + switch (rev_id) { + case 0x0: + hp_flags |= MV_HP_ERRATA_50XXB0; + break; + case 0x3: + hp_flags |= MV_HP_ERRATA_50XXB2; + break; + default: + dev_printk(KERN_WARNING, &pdev->dev, + "Applying B2 workarounds to unknown rev\n"); + hp_flags |= MV_HP_ERRATA_50XXB2; + break; + } + break; + + case chip_604x: + case chip_608x: + hpriv->ops = &mv6xxx_ops; + + switch (rev_id) { + case 0x7: + hp_flags |= MV_HP_ERRATA_60X1B2; + break; + case 0x9: + hp_flags |= MV_HP_ERRATA_60X1C0; + break; + default: + dev_printk(KERN_WARNING, &pdev->dev, + "Applying B2 workarounds to unknown rev\n"); + hp_flags |= MV_HP_ERRATA_60X1B2; + break; + } + break; + + case chip_7042: + case chip_6042: + hpriv->ops = &mv6xxx_ops; + + hp_flags |= MV_HP_GEN_IIE; + + switch (rev_id) { + case 0x0: + hp_flags |= MV_HP_ERRATA_XX42A0; + break; + case 0x1: + hp_flags |= MV_HP_ERRATA_60X1C0; + break; + default: + dev_printk(KERN_WARNING, &pdev->dev, + "Applying 60X1C0 workarounds to unknown rev\n"); + hp_flags |= MV_HP_ERRATA_60X1C0; + break; + } + break; + + default: + printk(KERN_ERR DRV_NAME ": BUG: invalid board index %u\n", board_idx); + return 1; + } + + hpriv->hp_flags = hp_flags; + + return 0; +} + +/** + * mv_init_host - Perform some early initialization of the host. + * @pdev: host PCI device + * @probe_ent: early data struct representing the host + * + * If possible, do an early global reset of the host. Then do + * our port init and clear/unmask all/relevant host interrupts. + * + * LOCKING: + * Inherited from caller. + */ +static int mv_init_host(struct pci_dev *pdev, struct ata_probe_ent *probe_ent, + unsigned int board_idx) +{ + int rc = 0, n_hc, port, hc; + void __iomem *mmio = probe_ent->mmio_base; + struct mv_host_priv *hpriv = probe_ent->private_data; + + /* global interrupt mask */ + writel(0, mmio + HC_MAIN_IRQ_MASK_OFS); + + rc = mv_chip_id(pdev, hpriv, board_idx); + if (rc) + goto done; + + n_hc = mv_get_hc_count(probe_ent->port_flags); + probe_ent->n_ports = MV_PORTS_PER_HC * n_hc; + + for (port = 0; port < probe_ent->n_ports; port++) + hpriv->ops->read_preamp(hpriv, port, mmio); + + rc = hpriv->ops->reset_hc(hpriv, mmio, n_hc); + if (rc) + goto done; + + hpriv->ops->reset_flash(hpriv, mmio); + hpriv->ops->reset_bus(pdev, mmio); + hpriv->ops->enable_leds(hpriv, mmio); + + for (port = 0; port < probe_ent->n_ports; port++) { + if (IS_60XX(hpriv)) { + void __iomem *port_mmio = mv_port_base(mmio, port); + + u32 ifctl = readl(port_mmio + SATA_INTERFACE_CTL); + ifctl |= (1 << 7); /* enable gen2i speed */ + ifctl = (ifctl & 0xfff) | 0x9b1000; /* from chip spec */ + writelfl(ifctl, port_mmio + SATA_INTERFACE_CTL); + } + + hpriv->ops->phy_errata(hpriv, mmio, port); + } + + for (port = 0; port < probe_ent->n_ports; port++) { + void __iomem *port_mmio = mv_port_base(mmio, port); + mv_port_init(&probe_ent->port[port], port_mmio); + } + + for (hc = 0; hc < n_hc; hc++) { + void __iomem *hc_mmio = mv_hc_base(mmio, hc); + + VPRINTK("HC%i: HC config=0x%08x HC IRQ cause " + "(before clear)=0x%08x\n", hc, + readl(hc_mmio + HC_CFG_OFS), + readl(hc_mmio + HC_IRQ_CAUSE_OFS)); + + /* Clear any currently outstanding hc interrupt conditions */ + writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS); + } + + /* Clear any currently outstanding host interrupt conditions */ + writelfl(0, mmio + PCI_IRQ_CAUSE_OFS); + + /* and unmask interrupt generation for host regs */ + writelfl(PCI_UNMASK_ALL_IRQS, mmio + PCI_IRQ_MASK_OFS); + writelfl(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS); + + VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x " + "PCI int cause/mask=0x%08x/0x%08x\n", + readl(mmio + HC_MAIN_IRQ_CAUSE_OFS), + readl(mmio + HC_MAIN_IRQ_MASK_OFS), + readl(mmio + PCI_IRQ_CAUSE_OFS), + readl(mmio + PCI_IRQ_MASK_OFS)); + +done: + return rc; +} + +/** + * mv_print_info - Dump key info to kernel log for perusal. + * @probe_ent: early data struct representing the host + * + * FIXME: complete this. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_print_info(struct ata_probe_ent *probe_ent) +{ + struct pci_dev *pdev = to_pci_dev(probe_ent->dev); + struct mv_host_priv *hpriv = probe_ent->private_data; + u8 rev_id, scc; + const char *scc_s; + + /* Use this to determine the HW stepping of the chip so we know + * what errata to workaround + */ + pci_read_config_byte(pdev, PCI_REVISION_ID, &rev_id); + + pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &scc); + if (scc == 0) + scc_s = "SCSI"; + else if (scc == 0x01) + scc_s = "RAID"; + else + scc_s = "unknown"; + + dev_printk(KERN_INFO, &pdev->dev, + "%u slots %u ports %s mode IRQ via %s\n", + (unsigned)MV_MAX_Q_DEPTH, probe_ent->n_ports, + scc_s, (MV_HP_FLAG_MSI & hpriv->hp_flags) ? "MSI" : "INTx"); +} + +/** + * mv_init_one - handle a positive probe of a Marvell host + * @pdev: PCI device found + * @ent: PCI device ID entry for the matched host + * + * LOCKING: + * Inherited from caller. + */ +static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version = 0; + struct ata_probe_ent *probe_ent = NULL; + struct mv_host_priv *hpriv; + unsigned int board_idx = (unsigned int)ent->driver_data; + void __iomem *mmio_base; + int pci_dev_busy = 0, rc; + + if (!printed_version++) + dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) { + return rc; + } + pci_set_master(pdev); + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, MV_PRIMARY_BAR, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + + hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL); + if (!hpriv) { + rc = -ENOMEM; + goto err_out_iounmap; + } + memset(hpriv, 0, sizeof(*hpriv)); + + probe_ent->sht = mv_port_info[board_idx].sht; + probe_ent->port_flags = mv_port_info[board_idx].flags; + probe_ent->pio_mask = mv_port_info[board_idx].pio_mask; + probe_ent->udma_mask = mv_port_info[board_idx].udma_mask; + probe_ent->port_ops = mv_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + probe_ent->private_data = hpriv; + + /* initialize adapter */ + rc = mv_init_host(pdev, probe_ent, board_idx); + if (rc) { + goto err_out_hpriv; + } + + /* Enable interrupts */ + if (msi && pci_enable_msi(pdev) == 0) { + hpriv->hp_flags |= MV_HP_FLAG_MSI; + } else { + pci_intx(pdev, 1); + } + + mv_dump_pci_cfg(pdev, 0x68); + mv_print_info(probe_ent); + + if (ata_device_add(probe_ent) == 0) { + rc = -ENODEV; /* No devices discovered */ + goto err_out_dev_add; + } + + kfree(probe_ent); + return 0; + +err_out_dev_add: + if (MV_HP_FLAG_MSI & hpriv->hp_flags) { + pci_disable_msi(pdev); + } else { + pci_intx(pdev, 0); + } +err_out_hpriv: + kfree(hpriv); +err_out_iounmap: + pci_iounmap(pdev, mmio_base); +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) { + pci_disable_device(pdev); + } + + return rc; +} + +static int __init mv_init(void) +{ + return pci_register_driver(&mv_pci_driver); +} + +static void __exit mv_exit(void) +{ + pci_unregister_driver(&mv_pci_driver); +} + +MODULE_AUTHOR("Brett Russ"); +MODULE_DESCRIPTION("SCSI low-level driver for Marvell SATA controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, mv_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_param(msi, int, 0444); +MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)"); + +module_init(mv_init); +module_exit(mv_exit); diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c new file mode 100644 index 00000000000..8cd730fe5dd --- /dev/null +++ b/drivers/ata/sata_nv.c @@ -0,0 +1,595 @@ +/* + * sata_nv.c - NVIDIA nForce SATA + * + * Copyright 2004 NVIDIA Corp. All rights reserved. + * Copyright 2004 Andrew Chew + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * No hardware documentation available outside of NVIDIA. + * This driver programs the NVIDIA SATA controller in a similar + * fashion as with other PCI IDE BMDMA controllers, with a few + * NV-specific details such as register offsets, SATA phy location, + * hotplug info, etc. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "sata_nv" +#define DRV_VERSION "2.0" + +enum { + NV_PORTS = 2, + NV_PIO_MASK = 0x1f, + NV_MWDMA_MASK = 0x07, + NV_UDMA_MASK = 0x7f, + NV_PORT0_SCR_REG_OFFSET = 0x00, + NV_PORT1_SCR_REG_OFFSET = 0x40, + + /* INT_STATUS/ENABLE */ + NV_INT_STATUS = 0x10, + NV_INT_ENABLE = 0x11, + NV_INT_STATUS_CK804 = 0x440, + NV_INT_ENABLE_CK804 = 0x441, + + /* INT_STATUS/ENABLE bits */ + NV_INT_DEV = 0x01, + NV_INT_PM = 0x02, + NV_INT_ADDED = 0x04, + NV_INT_REMOVED = 0x08, + + NV_INT_PORT_SHIFT = 4, /* each port occupies 4 bits */ + + NV_INT_ALL = 0x0f, + NV_INT_MASK = NV_INT_DEV | + NV_INT_ADDED | NV_INT_REMOVED, + + /* INT_CONFIG */ + NV_INT_CONFIG = 0x12, + NV_INT_CONFIG_METHD = 0x01, // 0 = INT, 1 = SMI + + // For PCI config register 20 + NV_MCP_SATA_CFG_20 = 0x50, + NV_MCP_SATA_CFG_20_SATA_SPACE_EN = 0x04, +}; + +static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static void nv_ck804_host_stop(struct ata_host *host); +static irqreturn_t nv_generic_interrupt(int irq, void *dev_instance, + struct pt_regs *regs); +static irqreturn_t nv_nf2_interrupt(int irq, void *dev_instance, + struct pt_regs *regs); +static irqreturn_t nv_ck804_interrupt(int irq, void *dev_instance, + struct pt_regs *regs); +static u32 nv_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void nv_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); + +static void nv_nf2_freeze(struct ata_port *ap); +static void nv_nf2_thaw(struct ata_port *ap); +static void nv_ck804_freeze(struct ata_port *ap); +static void nv_ck804_thaw(struct ata_port *ap); +static void nv_error_handler(struct ata_port *ap); + +enum nv_host_type +{ + GENERIC, + NFORCE2, + NFORCE3 = NFORCE2, /* NF2 == NF3 as far as sata_nv is concerned */ + CK804 +}; + +static const struct pci_device_id nv_pci_tbl[] = { + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, NFORCE2 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, NFORCE3 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, NFORCE3 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_SATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_SATA2, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA2, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA2, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_SATA3, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, 0x045c, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, 0x045d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, 0x045e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, 0x045f, PCI_ANY_ID, PCI_ANY_ID, 0, 0, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_STORAGE_IDE<<8, 0xffff00, GENERIC }, + { PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_STORAGE_RAID<<8, 0xffff00, GENERIC }, + { 0, } /* terminate list */ +}; + +static struct pci_driver nv_pci_driver = { + .name = DRV_NAME, + .id_table = nv_pci_tbl, + .probe = nv_init_one, + .remove = ata_pci_remove_one, +}; + +static struct scsi_host_template nv_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations nv_generic_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .exec_command = ata_exec_command, + .check_status = ata_check_status, + .dev_select = ata_std_dev_select, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = nv_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .data_xfer = ata_pio_data_xfer, + .irq_handler = nv_generic_interrupt, + .irq_clear = ata_bmdma_irq_clear, + .scr_read = nv_scr_read, + .scr_write = nv_scr_write, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static const struct ata_port_operations nv_nf2_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .exec_command = ata_exec_command, + .check_status = ata_check_status, + .dev_select = ata_std_dev_select, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .freeze = nv_nf2_freeze, + .thaw = nv_nf2_thaw, + .error_handler = nv_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .data_xfer = ata_pio_data_xfer, + .irq_handler = nv_nf2_interrupt, + .irq_clear = ata_bmdma_irq_clear, + .scr_read = nv_scr_read, + .scr_write = nv_scr_write, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static const struct ata_port_operations nv_ck804_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .exec_command = ata_exec_command, + .check_status = ata_check_status, + .dev_select = ata_std_dev_select, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .freeze = nv_ck804_freeze, + .thaw = nv_ck804_thaw, + .error_handler = nv_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .data_xfer = ata_pio_data_xfer, + .irq_handler = nv_ck804_interrupt, + .irq_clear = ata_bmdma_irq_clear, + .scr_read = nv_scr_read, + .scr_write = nv_scr_write, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = nv_ck804_host_stop, +}; + +static struct ata_port_info nv_port_info[] = { + /* generic */ + { + .sht = &nv_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY, + .pio_mask = NV_PIO_MASK, + .mwdma_mask = NV_MWDMA_MASK, + .udma_mask = NV_UDMA_MASK, + .port_ops = &nv_generic_ops, + }, + /* nforce2/3 */ + { + .sht = &nv_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY, + .pio_mask = NV_PIO_MASK, + .mwdma_mask = NV_MWDMA_MASK, + .udma_mask = NV_UDMA_MASK, + .port_ops = &nv_nf2_ops, + }, + /* ck804 */ + { + .sht = &nv_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY, + .pio_mask = NV_PIO_MASK, + .mwdma_mask = NV_MWDMA_MASK, + .udma_mask = NV_UDMA_MASK, + .port_ops = &nv_ck804_ops, + }, +}; + +MODULE_AUTHOR("NVIDIA"); +MODULE_DESCRIPTION("low-level driver for NVIDIA nForce SATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, nv_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +static irqreturn_t nv_generic_interrupt(int irq, void *dev_instance, + struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + unsigned int i; + unsigned int handled = 0; + unsigned long flags; + + spin_lock_irqsave(&host->lock, flags); + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap; + + ap = host->ports[i]; + if (ap && + !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) + handled += ata_host_intr(ap, qc); + else + // No request pending? Clear interrupt status + // anyway, in case there's one pending. + ap->ops->check_status(ap); + } + + } + + spin_unlock_irqrestore(&host->lock, flags); + + return IRQ_RETVAL(handled); +} + +static int nv_host_intr(struct ata_port *ap, u8 irq_stat) +{ + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag); + int handled; + + /* freeze if hotplugged */ + if (unlikely(irq_stat & (NV_INT_ADDED | NV_INT_REMOVED))) { + ata_port_freeze(ap); + return 1; + } + + /* bail out if not our interrupt */ + if (!(irq_stat & NV_INT_DEV)) + return 0; + + /* DEV interrupt w/ no active qc? */ + if (unlikely(!qc || (qc->tf.flags & ATA_TFLAG_POLLING))) { + ata_check_status(ap); + return 1; + } + + /* handle interrupt */ + handled = ata_host_intr(ap, qc); + if (unlikely(!handled)) { + /* spurious, clear it */ + ata_check_status(ap); + } + + return 1; +} + +static irqreturn_t nv_do_interrupt(struct ata_host *host, u8 irq_stat) +{ + int i, handled = 0; + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + + if (ap && !(ap->flags & ATA_FLAG_DISABLED)) + handled += nv_host_intr(ap, irq_stat); + + irq_stat >>= NV_INT_PORT_SHIFT; + } + + return IRQ_RETVAL(handled); +} + +static irqreturn_t nv_nf2_interrupt(int irq, void *dev_instance, + struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + u8 irq_stat; + irqreturn_t ret; + + spin_lock(&host->lock); + irq_stat = inb(host->ports[0]->ioaddr.scr_addr + NV_INT_STATUS); + ret = nv_do_interrupt(host, irq_stat); + spin_unlock(&host->lock); + + return ret; +} + +static irqreturn_t nv_ck804_interrupt(int irq, void *dev_instance, + struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + u8 irq_stat; + irqreturn_t ret; + + spin_lock(&host->lock); + irq_stat = readb(host->mmio_base + NV_INT_STATUS_CK804); + ret = nv_do_interrupt(host, irq_stat); + spin_unlock(&host->lock); + + return ret; +} + +static u32 nv_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + if (sc_reg > SCR_CONTROL) + return 0xffffffffU; + + return ioread32((void __iomem *)ap->ioaddr.scr_addr + (sc_reg * 4)); +} + +static void nv_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val) +{ + if (sc_reg > SCR_CONTROL) + return; + + iowrite32(val, (void __iomem *)ap->ioaddr.scr_addr + (sc_reg * 4)); +} + +static void nv_nf2_freeze(struct ata_port *ap) +{ + unsigned long scr_addr = ap->host->ports[0]->ioaddr.scr_addr; + int shift = ap->port_no * NV_INT_PORT_SHIFT; + u8 mask; + + mask = inb(scr_addr + NV_INT_ENABLE); + mask &= ~(NV_INT_ALL << shift); + outb(mask, scr_addr + NV_INT_ENABLE); +} + +static void nv_nf2_thaw(struct ata_port *ap) +{ + unsigned long scr_addr = ap->host->ports[0]->ioaddr.scr_addr; + int shift = ap->port_no * NV_INT_PORT_SHIFT; + u8 mask; + + outb(NV_INT_ALL << shift, scr_addr + NV_INT_STATUS); + + mask = inb(scr_addr + NV_INT_ENABLE); + mask |= (NV_INT_MASK << shift); + outb(mask, scr_addr + NV_INT_ENABLE); +} + +static void nv_ck804_freeze(struct ata_port *ap) +{ + void __iomem *mmio_base = ap->host->mmio_base; + int shift = ap->port_no * NV_INT_PORT_SHIFT; + u8 mask; + + mask = readb(mmio_base + NV_INT_ENABLE_CK804); + mask &= ~(NV_INT_ALL << shift); + writeb(mask, mmio_base + NV_INT_ENABLE_CK804); +} + +static void nv_ck804_thaw(struct ata_port *ap) +{ + void __iomem *mmio_base = ap->host->mmio_base; + int shift = ap->port_no * NV_INT_PORT_SHIFT; + u8 mask; + + writeb(NV_INT_ALL << shift, mmio_base + NV_INT_STATUS_CK804); + + mask = readb(mmio_base + NV_INT_ENABLE_CK804); + mask |= (NV_INT_MASK << shift); + writeb(mask, mmio_base + NV_INT_ENABLE_CK804); +} + +static int nv_hardreset(struct ata_port *ap, unsigned int *class) +{ + unsigned int dummy; + + /* SATA hardreset fails to retrieve proper device signature on + * some controllers. Don't classify on hardreset. For more + * info, see http://bugme.osdl.org/show_bug.cgi?id=3352 + */ + return sata_std_hardreset(ap, &dummy); +} + +static void nv_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, ata_std_prereset, ata_std_softreset, + nv_hardreset, ata_std_postreset); +} + +static int nv_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version = 0; + struct ata_port_info *ppi[2]; + struct ata_probe_ent *probe_ent; + int pci_dev_busy = 0; + int rc; + u32 bar; + unsigned long base; + + // Make sure this is a SATA controller by counting the number of bars + // (NVIDIA SATA controllers will always have six bars). Otherwise, + // it's an IDE controller and we ignore it. + for (bar=0; bar<6; bar++) + if (pci_resource_start(pdev, bar) == 0) + return -ENODEV; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + goto err_out; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out_disable; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + rc = -ENOMEM; + + ppi[0] = ppi[1] = &nv_port_info[ent->driver_data]; + probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY); + if (!probe_ent) + goto err_out_regions; + + probe_ent->mmio_base = pci_iomap(pdev, 5, 0); + if (!probe_ent->mmio_base) { + rc = -EIO; + goto err_out_free_ent; + } + + base = (unsigned long)probe_ent->mmio_base; + + probe_ent->port[0].scr_addr = base + NV_PORT0_SCR_REG_OFFSET; + probe_ent->port[1].scr_addr = base + NV_PORT1_SCR_REG_OFFSET; + + /* enable SATA space for CK804 */ + if (ent->driver_data == CK804) { + u8 regval; + + pci_read_config_byte(pdev, NV_MCP_SATA_CFG_20, ®val); + regval |= NV_MCP_SATA_CFG_20_SATA_SPACE_EN; + pci_write_config_byte(pdev, NV_MCP_SATA_CFG_20, regval); + } + + pci_set_master(pdev); + + rc = ata_device_add(probe_ent); + if (rc != NV_PORTS) + goto err_out_iounmap; + + kfree(probe_ent); + + return 0; + +err_out_iounmap: + pci_iounmap(pdev, probe_ent->mmio_base); +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out_disable: + if (!pci_dev_busy) + pci_disable_device(pdev); +err_out: + return rc; +} + +static void nv_ck804_host_stop(struct ata_host *host) +{ + struct pci_dev *pdev = to_pci_dev(host->dev); + u8 regval; + + /* disable SATA space for CK804 */ + pci_read_config_byte(pdev, NV_MCP_SATA_CFG_20, ®val); + regval &= ~NV_MCP_SATA_CFG_20_SATA_SPACE_EN; + pci_write_config_byte(pdev, NV_MCP_SATA_CFG_20, regval); + + ata_pci_host_stop(host); +} + +static int __init nv_init(void) +{ + return pci_register_driver(&nv_pci_driver); +} + +static void __exit nv_exit(void) +{ + pci_unregister_driver(&nv_pci_driver); +} + +module_init(nv_init); +module_exit(nv_exit); diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c new file mode 100644 index 00000000000..d627812ea73 --- /dev/null +++ b/drivers/ata/sata_promise.c @@ -0,0 +1,844 @@ +/* + * sata_promise.c - Promise SATA + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2003-2004 Red Hat, Inc. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware information only available under NDA. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <linux/libata.h> +#include <asm/io.h> +#include "sata_promise.h" + +#define DRV_NAME "sata_promise" +#define DRV_VERSION "1.04" + + +enum { + PDC_PKT_SUBMIT = 0x40, /* Command packet pointer addr */ + PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */ + PDC_TBG_MODE = 0x41, /* TBG mode */ + PDC_FLASH_CTL = 0x44, /* Flash control register */ + PDC_PCI_CTL = 0x48, /* PCI control and status register */ + PDC_GLOBAL_CTL = 0x48, /* Global control/status (per port) */ + PDC_CTLSTAT = 0x60, /* IDE control and status (per port) */ + PDC_SATA_PLUG_CSR = 0x6C, /* SATA Plug control/status reg */ + PDC2_SATA_PLUG_CSR = 0x60, /* SATAII Plug control/status reg */ + PDC_SLEW_CTL = 0x470, /* slew rate control reg */ + + PDC_ERR_MASK = (1<<19) | (1<<20) | (1<<21) | (1<<22) | + (1<<8) | (1<<9) | (1<<10), + + board_2037x = 0, /* FastTrak S150 TX2plus */ + board_20319 = 1, /* FastTrak S150 TX4 */ + board_20619 = 2, /* FastTrak TX4000 */ + board_20771 = 3, /* FastTrak TX2300 */ + board_2057x = 4, /* SATAII150 Tx2plus */ + board_40518 = 5, /* SATAII150 Tx4 */ + + PDC_HAS_PATA = (1 << 1), /* PDC20375/20575 has PATA */ + + PDC_RESET = (1 << 11), /* HDMA reset */ + + PDC_COMMON_FLAGS = ATA_FLAG_NO_LEGACY | ATA_FLAG_SRST | + ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI | + ATA_FLAG_PIO_POLLING, +}; + + +struct pdc_port_priv { + u8 *pkt; + dma_addr_t pkt_dma; +}; + +struct pdc_host_priv { + int hotplug_offset; +}; + +static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void pdc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); +static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *regs); +static void pdc_eng_timeout(struct ata_port *ap); +static int pdc_port_start(struct ata_port *ap); +static void pdc_port_stop(struct ata_port *ap); +static void pdc_pata_phy_reset(struct ata_port *ap); +static void pdc_sata_phy_reset(struct ata_port *ap); +static void pdc_qc_prep(struct ata_queued_cmd *qc); +static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf); +static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf); +static void pdc_irq_clear(struct ata_port *ap); +static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc); +static void pdc_host_stop(struct ata_host *host); + + +static struct scsi_host_template pdc_ata_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations pdc_sata_ops = { + .port_disable = ata_port_disable, + .tf_load = pdc_tf_load_mmio, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = pdc_exec_command_mmio, + .dev_select = ata_std_dev_select, + + .phy_reset = pdc_sata_phy_reset, + + .qc_prep = pdc_qc_prep, + .qc_issue = pdc_qc_issue_prot, + .eng_timeout = pdc_eng_timeout, + .data_xfer = ata_mmio_data_xfer, + .irq_handler = pdc_interrupt, + .irq_clear = pdc_irq_clear, + + .scr_read = pdc_sata_scr_read, + .scr_write = pdc_sata_scr_write, + .port_start = pdc_port_start, + .port_stop = pdc_port_stop, + .host_stop = pdc_host_stop, +}; + +static const struct ata_port_operations pdc_pata_ops = { + .port_disable = ata_port_disable, + .tf_load = pdc_tf_load_mmio, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = pdc_exec_command_mmio, + .dev_select = ata_std_dev_select, + + .phy_reset = pdc_pata_phy_reset, + + .qc_prep = pdc_qc_prep, + .qc_issue = pdc_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + .eng_timeout = pdc_eng_timeout, + .irq_handler = pdc_interrupt, + .irq_clear = pdc_irq_clear, + + .port_start = pdc_port_start, + .port_stop = pdc_port_stop, + .host_stop = pdc_host_stop, +}; + +static const struct ata_port_info pdc_port_info[] = { + /* board_2037x */ + { + .sht = &pdc_ata_sht, + .flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &pdc_sata_ops, + }, + + /* board_20319 */ + { + .sht = &pdc_ata_sht, + .flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &pdc_sata_ops, + }, + + /* board_20619 */ + { + .sht = &pdc_ata_sht, + .flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &pdc_pata_ops, + }, + + /* board_20771 */ + { + .sht = &pdc_ata_sht, + .flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &pdc_sata_ops, + }, + + /* board_2057x */ + { + .sht = &pdc_ata_sht, + .flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &pdc_sata_ops, + }, + + /* board_40518 */ + { + .sht = &pdc_ata_sht, + .flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &pdc_sata_ops, + }, +}; + +static const struct pci_device_id pdc_ata_pci_tbl[] = { + { PCI_VENDOR_ID_PROMISE, 0x3371, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2037x }, + { PCI_VENDOR_ID_PROMISE, 0x3570, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2037x }, + { PCI_VENDOR_ID_PROMISE, 0x3571, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2037x }, + { PCI_VENDOR_ID_PROMISE, 0x3373, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2037x }, + { PCI_VENDOR_ID_PROMISE, 0x3375, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2037x }, + { PCI_VENDOR_ID_PROMISE, 0x3376, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2037x }, + { PCI_VENDOR_ID_PROMISE, 0x3574, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2057x }, + { PCI_VENDOR_ID_PROMISE, 0x3d75, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2057x }, + { PCI_VENDOR_ID_PROMISE, 0x3d73, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2037x }, + + { PCI_VENDOR_ID_PROMISE, 0x3318, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20319 }, + { PCI_VENDOR_ID_PROMISE, 0x3319, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20319 }, + { PCI_VENDOR_ID_PROMISE, 0x3515, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20319 }, + { PCI_VENDOR_ID_PROMISE, 0x3519, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20319 }, + { PCI_VENDOR_ID_PROMISE, 0x3d17, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20319 }, + { PCI_VENDOR_ID_PROMISE, 0x3d18, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_40518 }, + + { PCI_VENDOR_ID_PROMISE, 0x6629, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20619 }, + +/* TODO: remove all associated board_20771 code, as it completely + * duplicates board_2037x code, unless reason for separation can be + * divined. + */ +#if 0 + { PCI_VENDOR_ID_PROMISE, 0x3570, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20771 }, +#endif + + { } /* terminate list */ +}; + + +static struct pci_driver pdc_ata_pci_driver = { + .name = DRV_NAME, + .id_table = pdc_ata_pci_tbl, + .probe = pdc_ata_init_one, + .remove = ata_pci_remove_one, +}; + + +static int pdc_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct pdc_port_priv *pp; + int rc; + + rc = ata_port_start(ap); + if (rc) + return rc; + + pp = kzalloc(sizeof(*pp), GFP_KERNEL); + if (!pp) { + rc = -ENOMEM; + goto err_out; + } + + pp->pkt = dma_alloc_coherent(dev, 128, &pp->pkt_dma, GFP_KERNEL); + if (!pp->pkt) { + rc = -ENOMEM; + goto err_out_kfree; + } + + ap->private_data = pp; + + return 0; + +err_out_kfree: + kfree(pp); +err_out: + ata_port_stop(ap); + return rc; +} + + +static void pdc_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct pdc_port_priv *pp = ap->private_data; + + ap->private_data = NULL; + dma_free_coherent(dev, 128, pp->pkt, pp->pkt_dma); + kfree(pp); + ata_port_stop(ap); +} + + +static void pdc_host_stop(struct ata_host *host) +{ + struct pdc_host_priv *hp = host->private_data; + + ata_pci_host_stop(host); + + kfree(hp); +} + + +static void pdc_reset_port(struct ata_port *ap) +{ + void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr + PDC_CTLSTAT; + unsigned int i; + u32 tmp; + + for (i = 11; i > 0; i--) { + tmp = readl(mmio); + if (tmp & PDC_RESET) + break; + + udelay(100); + + tmp |= PDC_RESET; + writel(tmp, mmio); + } + + tmp &= ~PDC_RESET; + writel(tmp, mmio); + readl(mmio); /* flush */ +} + +static void pdc_sata_phy_reset(struct ata_port *ap) +{ + pdc_reset_port(ap); + sata_phy_reset(ap); +} + +static void pdc_pata_cbl_detect(struct ata_port *ap) +{ + u8 tmp; + void __iomem *mmio = (void *) ap->ioaddr.cmd_addr + PDC_CTLSTAT + 0x03; + + tmp = readb(mmio); + + if (tmp & 0x01) { + ap->cbl = ATA_CBL_PATA40; + ap->udma_mask &= ATA_UDMA_MASK_40C; + } else + ap->cbl = ATA_CBL_PATA80; +} + +static void pdc_pata_phy_reset(struct ata_port *ap) +{ + pdc_pata_cbl_detect(ap); + pdc_reset_port(ap); + ata_port_probe(ap); + ata_bus_reset(ap); +} + +static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + if (sc_reg > SCR_CONTROL) + return 0xffffffffU; + return readl((void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + + +static void pdc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg, + u32 val) +{ + if (sc_reg > SCR_CONTROL) + return; + writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + +static void pdc_qc_prep(struct ata_queued_cmd *qc) +{ + struct pdc_port_priv *pp = qc->ap->private_data; + unsigned int i; + + VPRINTK("ENTER\n"); + + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + ata_qc_prep(qc); + /* fall through */ + + case ATA_PROT_NODATA: + i = pdc_pkt_header(&qc->tf, qc->ap->prd_dma, + qc->dev->devno, pp->pkt); + + if (qc->tf.flags & ATA_TFLAG_LBA48) + i = pdc_prep_lba48(&qc->tf, pp->pkt, i); + else + i = pdc_prep_lba28(&qc->tf, pp->pkt, i); + + pdc_pkt_footer(&qc->tf, pp->pkt, i); + break; + + default: + break; + } +} + +static void pdc_eng_timeout(struct ata_port *ap) +{ + struct ata_host *host = ap->host; + u8 drv_stat; + struct ata_queued_cmd *qc; + unsigned long flags; + + DPRINTK("ENTER\n"); + + spin_lock_irqsave(&host->lock, flags); + + qc = ata_qc_from_tag(ap, ap->active_tag); + + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + case ATA_PROT_NODATA: + ata_port_printk(ap, KERN_ERR, "command timeout\n"); + drv_stat = ata_wait_idle(ap); + qc->err_mask |= __ac_err_mask(drv_stat); + break; + + default: + drv_stat = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000); + + ata_port_printk(ap, KERN_ERR, + "unknown timeout, cmd 0x%x stat 0x%x\n", + qc->tf.command, drv_stat); + + qc->err_mask |= ac_err_mask(drv_stat); + break; + } + + spin_unlock_irqrestore(&host->lock, flags); + ata_eh_qc_complete(qc); + DPRINTK("EXIT\n"); +} + +static inline unsigned int pdc_host_intr( struct ata_port *ap, + struct ata_queued_cmd *qc) +{ + unsigned int handled = 0; + u32 tmp; + void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr + PDC_GLOBAL_CTL; + + tmp = readl(mmio); + if (tmp & PDC_ERR_MASK) { + qc->err_mask |= AC_ERR_DEV; + pdc_reset_port(ap); + } + + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + case ATA_PROT_NODATA: + qc->err_mask |= ac_err_mask(ata_wait_idle(ap)); + ata_qc_complete(qc); + handled = 1; + break; + + default: + ap->stats.idle_irq++; + break; + } + + return handled; +} + +static void pdc_irq_clear(struct ata_port *ap) +{ + struct ata_host *host = ap->host; + void __iomem *mmio = host->mmio_base; + + readl(mmio + PDC_INT_SEQMASK); +} + +static irqreturn_t pdc_interrupt (int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + struct ata_port *ap; + u32 mask = 0; + unsigned int i, tmp; + unsigned int handled = 0; + void __iomem *mmio_base; + + VPRINTK("ENTER\n"); + + if (!host || !host->mmio_base) { + VPRINTK("QUICK EXIT\n"); + return IRQ_NONE; + } + + mmio_base = host->mmio_base; + + /* reading should also clear interrupts */ + mask = readl(mmio_base + PDC_INT_SEQMASK); + + if (mask == 0xffffffff) { + VPRINTK("QUICK EXIT 2\n"); + return IRQ_NONE; + } + + spin_lock(&host->lock); + + mask &= 0xffff; /* only 16 tags possible */ + if (!mask) { + VPRINTK("QUICK EXIT 3\n"); + goto done_irq; + } + + writel(mask, mmio_base + PDC_INT_SEQMASK); + + for (i = 0; i < host->n_ports; i++) { + VPRINTK("port %u\n", i); + ap = host->ports[i]; + tmp = mask & (1 << (i + 1)); + if (tmp && ap && + !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) + handled += pdc_host_intr(ap, qc); + } + } + + VPRINTK("EXIT\n"); + +done_irq: + spin_unlock(&host->lock); + return IRQ_RETVAL(handled); +} + +static inline void pdc_packet_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pdc_port_priv *pp = ap->private_data; + unsigned int port_no = ap->port_no; + u8 seq = (u8) (port_no + 1); + + VPRINTK("ENTER, ap %p\n", ap); + + writel(0x00000001, ap->host->mmio_base + (seq * 4)); + readl(ap->host->mmio_base + (seq * 4)); /* flush */ + + pp->pkt[2] = seq; + wmb(); /* flush PRD, pkt writes */ + writel(pp->pkt_dma, (void __iomem *) ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); + readl((void __iomem *) ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); /* flush */ +} + +static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc) +{ + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + case ATA_PROT_NODATA: + pdc_packet_start(qc); + return 0; + + case ATA_PROT_ATAPI_DMA: + BUG(); + break; + + default: + break; + } + + return ata_qc_issue_prot(qc); +} + +static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + WARN_ON (tf->protocol == ATA_PROT_DMA || + tf->protocol == ATA_PROT_NODATA); + ata_tf_load(ap, tf); +} + + +static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + WARN_ON (tf->protocol == ATA_PROT_DMA || + tf->protocol == ATA_PROT_NODATA); + ata_exec_command(ap, tf); +} + + +static void pdc_ata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = base; + port->data_addr = base; + port->feature_addr = + port->error_addr = base + 0x4; + port->nsect_addr = base + 0x8; + port->lbal_addr = base + 0xc; + port->lbam_addr = base + 0x10; + port->lbah_addr = base + 0x14; + port->device_addr = base + 0x18; + port->command_addr = + port->status_addr = base + 0x1c; + port->altstatus_addr = + port->ctl_addr = base + 0x38; +} + + +static void pdc_host_init(unsigned int chip_id, struct ata_probe_ent *pe) +{ + void __iomem *mmio = pe->mmio_base; + struct pdc_host_priv *hp = pe->private_data; + int hotplug_offset = hp->hotplug_offset; + u32 tmp; + + /* + * Except for the hotplug stuff, this is voodoo from the + * Promise driver. Label this entire section + * "TODO: figure out why we do this" + */ + + /* change FIFO_SHD to 8 dwords, enable BMR_BURST */ + tmp = readl(mmio + PDC_FLASH_CTL); + tmp |= 0x12000; /* bit 16 (fifo 8 dw) and 13 (bmr burst?) */ + writel(tmp, mmio + PDC_FLASH_CTL); + + /* clear plug/unplug flags for all ports */ + tmp = readl(mmio + hotplug_offset); + writel(tmp | 0xff, mmio + hotplug_offset); + + /* mask plug/unplug ints */ + tmp = readl(mmio + hotplug_offset); + writel(tmp | 0xff0000, mmio + hotplug_offset); + + /* reduce TBG clock to 133 Mhz. */ + tmp = readl(mmio + PDC_TBG_MODE); + tmp &= ~0x30000; /* clear bit 17, 16*/ + tmp |= 0x10000; /* set bit 17:16 = 0:1 */ + writel(tmp, mmio + PDC_TBG_MODE); + + readl(mmio + PDC_TBG_MODE); /* flush */ + msleep(10); + + /* adjust slew rate control register. */ + tmp = readl(mmio + PDC_SLEW_CTL); + tmp &= 0xFFFFF03F; /* clear bit 11 ~ 6 */ + tmp |= 0x00000900; /* set bit 11-9 = 100b , bit 8-6 = 100 */ + writel(tmp, mmio + PDC_SLEW_CTL); +} + +static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + struct pdc_host_priv *hp; + unsigned long base; + void __iomem *mmio_base; + unsigned int board_idx = (unsigned int) ent->driver_data; + int pci_dev_busy = 0; + int rc; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, 3, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + base = (unsigned long) mmio_base; + + hp = kzalloc(sizeof(*hp), GFP_KERNEL); + if (hp == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + + /* Set default hotplug offset */ + hp->hotplug_offset = PDC_SATA_PLUG_CSR; + probe_ent->private_data = hp; + + probe_ent->sht = pdc_port_info[board_idx].sht; + probe_ent->port_flags = pdc_port_info[board_idx].flags; + probe_ent->pio_mask = pdc_port_info[board_idx].pio_mask; + probe_ent->mwdma_mask = pdc_port_info[board_idx].mwdma_mask; + probe_ent->udma_mask = pdc_port_info[board_idx].udma_mask; + probe_ent->port_ops = pdc_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + + pdc_ata_setup_port(&probe_ent->port[0], base + 0x200); + pdc_ata_setup_port(&probe_ent->port[1], base + 0x280); + + probe_ent->port[0].scr_addr = base + 0x400; + probe_ent->port[1].scr_addr = base + 0x500; + + /* notice 4-port boards */ + switch (board_idx) { + case board_40518: + /* Override hotplug offset for SATAII150 */ + hp->hotplug_offset = PDC2_SATA_PLUG_CSR; + /* Fall through */ + case board_20319: + probe_ent->n_ports = 4; + + pdc_ata_setup_port(&probe_ent->port[2], base + 0x300); + pdc_ata_setup_port(&probe_ent->port[3], base + 0x380); + + probe_ent->port[2].scr_addr = base + 0x600; + probe_ent->port[3].scr_addr = base + 0x700; + break; + case board_2057x: + /* Override hotplug offset for SATAII150 */ + hp->hotplug_offset = PDC2_SATA_PLUG_CSR; + /* Fall through */ + case board_2037x: + probe_ent->n_ports = 2; + break; + case board_20771: + probe_ent->n_ports = 2; + break; + case board_20619: + probe_ent->n_ports = 4; + + pdc_ata_setup_port(&probe_ent->port[2], base + 0x300); + pdc_ata_setup_port(&probe_ent->port[3], base + 0x380); + + probe_ent->port[2].scr_addr = base + 0x600; + probe_ent->port[3].scr_addr = base + 0x700; + break; + default: + BUG(); + break; + } + + pci_set_master(pdev); + + /* initialize adapter */ + pdc_host_init(board_idx, probe_ent); + + /* FIXME: Need any other frees than hp? */ + if (!ata_device_add(probe_ent)) + kfree(hp); + + kfree(probe_ent); + + return 0; + +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; +} + + +static int __init pdc_ata_init(void) +{ + return pci_register_driver(&pdc_ata_pci_driver); +} + + +static void __exit pdc_ata_exit(void) +{ + pci_unregister_driver(&pdc_ata_pci_driver); +} + + +MODULE_AUTHOR("Jeff Garzik"); +MODULE_DESCRIPTION("Promise ATA TX2/TX4/TX4000 low-level driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pdc_ata_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_init(pdc_ata_init); +module_exit(pdc_ata_exit); diff --git a/drivers/ata/sata_promise.h b/drivers/ata/sata_promise.h new file mode 100644 index 00000000000..6ee5e190262 --- /dev/null +++ b/drivers/ata/sata_promise.h @@ -0,0 +1,157 @@ +/* + * sata_promise.h - Promise SATA common definitions and inline funcs + * + * Copyright 2003-2004 Red Hat, Inc. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + */ + +#ifndef __SATA_PROMISE_H__ +#define __SATA_PROMISE_H__ + +#include <linux/ata.h> + +enum pdc_packet_bits { + PDC_PKT_READ = (1 << 2), + PDC_PKT_NODATA = (1 << 3), + + PDC_PKT_SIZEMASK = (1 << 7) | (1 << 6) | (1 << 5), + PDC_PKT_CLEAR_BSY = (1 << 4), + PDC_PKT_WAIT_DRDY = (1 << 3) | (1 << 4), + PDC_LAST_REG = (1 << 3), + + PDC_REG_DEVCTL = (1 << 3) | (1 << 2) | (1 << 1), +}; + +static inline unsigned int pdc_pkt_header(struct ata_taskfile *tf, + dma_addr_t sg_table, + unsigned int devno, u8 *buf) +{ + u8 dev_reg; + u32 *buf32 = (u32 *) buf; + + /* set control bits (byte 0), zero delay seq id (byte 3), + * and seq id (byte 2) + */ + switch (tf->protocol) { + case ATA_PROT_DMA: + if (!(tf->flags & ATA_TFLAG_WRITE)) + buf32[0] = cpu_to_le32(PDC_PKT_READ); + else + buf32[0] = 0; + break; + + case ATA_PROT_NODATA: + buf32[0] = cpu_to_le32(PDC_PKT_NODATA); + break; + + default: + BUG(); + break; + } + + buf32[1] = cpu_to_le32(sg_table); /* S/G table addr */ + buf32[2] = 0; /* no next-packet */ + + if (devno == 0) + dev_reg = ATA_DEVICE_OBS; + else + dev_reg = ATA_DEVICE_OBS | ATA_DEV1; + + /* select device */ + buf[12] = (1 << 5) | PDC_PKT_CLEAR_BSY | ATA_REG_DEVICE; + buf[13] = dev_reg; + + /* device control register */ + buf[14] = (1 << 5) | PDC_REG_DEVCTL; + buf[15] = tf->ctl; + + return 16; /* offset of next byte */ +} + +static inline unsigned int pdc_pkt_footer(struct ata_taskfile *tf, u8 *buf, + unsigned int i) +{ + if (tf->flags & ATA_TFLAG_DEVICE) { + buf[i++] = (1 << 5) | ATA_REG_DEVICE; + buf[i++] = tf->device; + } + + /* and finally the command itself; also includes end-of-pkt marker */ + buf[i++] = (1 << 5) | PDC_LAST_REG | ATA_REG_CMD; + buf[i++] = tf->command; + + return i; +} + +static inline unsigned int pdc_prep_lba28(struct ata_taskfile *tf, u8 *buf, unsigned int i) +{ + /* the "(1 << 5)" should be read "(count << 5)" */ + + /* ATA command block registers */ + buf[i++] = (1 << 5) | ATA_REG_FEATURE; + buf[i++] = tf->feature; + + buf[i++] = (1 << 5) | ATA_REG_NSECT; + buf[i++] = tf->nsect; + + buf[i++] = (1 << 5) | ATA_REG_LBAL; + buf[i++] = tf->lbal; + + buf[i++] = (1 << 5) | ATA_REG_LBAM; + buf[i++] = tf->lbam; + + buf[i++] = (1 << 5) | ATA_REG_LBAH; + buf[i++] = tf->lbah; + + return i; +} + +static inline unsigned int pdc_prep_lba48(struct ata_taskfile *tf, u8 *buf, unsigned int i) +{ + /* the "(2 << 5)" should be read "(count << 5)" */ + + /* ATA command block registers */ + buf[i++] = (2 << 5) | ATA_REG_FEATURE; + buf[i++] = tf->hob_feature; + buf[i++] = tf->feature; + + buf[i++] = (2 << 5) | ATA_REG_NSECT; + buf[i++] = tf->hob_nsect; + buf[i++] = tf->nsect; + + buf[i++] = (2 << 5) | ATA_REG_LBAL; + buf[i++] = tf->hob_lbal; + buf[i++] = tf->lbal; + + buf[i++] = (2 << 5) | ATA_REG_LBAM; + buf[i++] = tf->hob_lbam; + buf[i++] = tf->lbam; + + buf[i++] = (2 << 5) | ATA_REG_LBAH; + buf[i++] = tf->hob_lbah; + buf[i++] = tf->lbah; + + return i; +} + + +#endif /* __SATA_PROMISE_H__ */ diff --git a/drivers/ata/sata_qstor.c b/drivers/ata/sata_qstor.c new file mode 100644 index 00000000000..fa29dfe2a7b --- /dev/null +++ b/drivers/ata/sata_qstor.c @@ -0,0 +1,730 @@ +/* + * sata_qstor.c - Pacific Digital Corporation QStor SATA + * + * Maintained by: Mark Lord <mlord@pobox.com> + * + * Copyright 2005 Pacific Digital Corporation. + * (OSL/GPL code release authorized by Jalil Fadavi). + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <asm/io.h> +#include <linux/libata.h> + +#define DRV_NAME "sata_qstor" +#define DRV_VERSION "0.06" + +enum { + QS_PORTS = 4, + QS_MAX_PRD = LIBATA_MAX_PRD, + QS_CPB_ORDER = 6, + QS_CPB_BYTES = (1 << QS_CPB_ORDER), + QS_PRD_BYTES = QS_MAX_PRD * 16, + QS_PKT_BYTES = QS_CPB_BYTES + QS_PRD_BYTES, + + /* global register offsets */ + QS_HCF_CNFG3 = 0x0003, /* host configuration offset */ + QS_HID_HPHY = 0x0004, /* host physical interface info */ + QS_HCT_CTRL = 0x00e4, /* global interrupt mask offset */ + QS_HST_SFF = 0x0100, /* host status fifo offset */ + QS_HVS_SERD3 = 0x0393, /* PHY enable offset */ + + /* global control bits */ + QS_HPHY_64BIT = (1 << 1), /* 64-bit bus detected */ + QS_CNFG3_GSRST = 0x01, /* global chip reset */ + QS_SERD3_PHY_ENA = 0xf0, /* PHY detection ENAble*/ + + /* per-channel register offsets */ + QS_CCF_CPBA = 0x0710, /* chan CPB base address */ + QS_CCF_CSEP = 0x0718, /* chan CPB separation factor */ + QS_CFC_HUFT = 0x0800, /* host upstream fifo threshold */ + QS_CFC_HDFT = 0x0804, /* host downstream fifo threshold */ + QS_CFC_DUFT = 0x0808, /* dev upstream fifo threshold */ + QS_CFC_DDFT = 0x080c, /* dev downstream fifo threshold */ + QS_CCT_CTR0 = 0x0900, /* chan control-0 offset */ + QS_CCT_CTR1 = 0x0901, /* chan control-1 offset */ + QS_CCT_CFF = 0x0a00, /* chan command fifo offset */ + + /* channel control bits */ + QS_CTR0_REG = (1 << 1), /* register mode (vs. pkt mode) */ + QS_CTR0_CLER = (1 << 2), /* clear channel errors */ + QS_CTR1_RDEV = (1 << 1), /* sata phy/comms reset */ + QS_CTR1_RCHN = (1 << 4), /* reset channel logic */ + QS_CCF_RUN_PKT = 0x107, /* RUN a new dma PKT */ + + /* pkt sub-field headers */ + QS_HCB_HDR = 0x01, /* Host Control Block header */ + QS_DCB_HDR = 0x02, /* Device Control Block header */ + + /* pkt HCB flag bits */ + QS_HF_DIRO = (1 << 0), /* data DIRection Out */ + QS_HF_DAT = (1 << 3), /* DATa pkt */ + QS_HF_IEN = (1 << 4), /* Interrupt ENable */ + QS_HF_VLD = (1 << 5), /* VaLiD pkt */ + + /* pkt DCB flag bits */ + QS_DF_PORD = (1 << 2), /* Pio OR Dma */ + QS_DF_ELBA = (1 << 3), /* Extended LBA (lba48) */ + + /* PCI device IDs */ + board_2068_idx = 0, /* QStor 4-port SATA/RAID */ +}; + +enum { + QS_DMA_BOUNDARY = ~0UL +}; + +typedef enum { qs_state_idle, qs_state_pkt, qs_state_mmio } qs_state_t; + +struct qs_port_priv { + u8 *pkt; + dma_addr_t pkt_dma; + qs_state_t state; +}; + +static u32 qs_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void qs_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); +static int qs_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static irqreturn_t qs_intr (int irq, void *dev_instance, struct pt_regs *regs); +static int qs_port_start(struct ata_port *ap); +static void qs_host_stop(struct ata_host *host); +static void qs_port_stop(struct ata_port *ap); +static void qs_phy_reset(struct ata_port *ap); +static void qs_qc_prep(struct ata_queued_cmd *qc); +static unsigned int qs_qc_issue(struct ata_queued_cmd *qc); +static int qs_check_atapi_dma(struct ata_queued_cmd *qc); +static void qs_bmdma_stop(struct ata_queued_cmd *qc); +static u8 qs_bmdma_status(struct ata_port *ap); +static void qs_irq_clear(struct ata_port *ap); +static void qs_eng_timeout(struct ata_port *ap); + +static struct scsi_host_template qs_ata_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = QS_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + //FIXME .use_clustering = ATA_SHT_USE_CLUSTERING, + .use_clustering = ENABLE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = QS_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations qs_ata_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .check_atapi_dma = qs_check_atapi_dma, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .phy_reset = qs_phy_reset, + .qc_prep = qs_qc_prep, + .qc_issue = qs_qc_issue, + .data_xfer = ata_mmio_data_xfer, + .eng_timeout = qs_eng_timeout, + .irq_handler = qs_intr, + .irq_clear = qs_irq_clear, + .scr_read = qs_scr_read, + .scr_write = qs_scr_write, + .port_start = qs_port_start, + .port_stop = qs_port_stop, + .host_stop = qs_host_stop, + .bmdma_stop = qs_bmdma_stop, + .bmdma_status = qs_bmdma_status, +}; + +static const struct ata_port_info qs_port_info[] = { + /* board_2068_idx */ + { + .sht = &qs_ata_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_SATA_RESET | + //FIXME ATA_FLAG_SRST | + ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING, + .pio_mask = 0x10, /* pio4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &qs_ata_ops, + }, +}; + +static const struct pci_device_id qs_ata_pci_tbl[] = { + { PCI_VENDOR_ID_PDC, 0x2068, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_2068_idx }, + + { } /* terminate list */ +}; + +static struct pci_driver qs_ata_pci_driver = { + .name = DRV_NAME, + .id_table = qs_ata_pci_tbl, + .probe = qs_ata_init_one, + .remove = ata_pci_remove_one, +}; + +static int qs_check_atapi_dma(struct ata_queued_cmd *qc) +{ + return 1; /* ATAPI DMA not supported */ +} + +static void qs_bmdma_stop(struct ata_queued_cmd *qc) +{ + /* nothing */ +} + +static u8 qs_bmdma_status(struct ata_port *ap) +{ + return 0; +} + +static void qs_irq_clear(struct ata_port *ap) +{ + /* nothing */ +} + +static inline void qs_enter_reg_mode(struct ata_port *ap) +{ + u8 __iomem *chan = ap->host->mmio_base + (ap->port_no * 0x4000); + + writeb(QS_CTR0_REG, chan + QS_CCT_CTR0); + readb(chan + QS_CCT_CTR0); /* flush */ +} + +static inline void qs_reset_channel_logic(struct ata_port *ap) +{ + u8 __iomem *chan = ap->host->mmio_base + (ap->port_no * 0x4000); + + writeb(QS_CTR1_RCHN, chan + QS_CCT_CTR1); + readb(chan + QS_CCT_CTR0); /* flush */ + qs_enter_reg_mode(ap); +} + +static void qs_phy_reset(struct ata_port *ap) +{ + struct qs_port_priv *pp = ap->private_data; + + pp->state = qs_state_idle; + qs_reset_channel_logic(ap); + sata_phy_reset(ap); +} + +static void qs_eng_timeout(struct ata_port *ap) +{ + struct qs_port_priv *pp = ap->private_data; + + if (pp->state != qs_state_idle) /* healthy paranoia */ + pp->state = qs_state_mmio; + qs_reset_channel_logic(ap); + ata_eng_timeout(ap); +} + +static u32 qs_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + if (sc_reg > SCR_CONTROL) + return ~0U; + return readl((void __iomem *)(ap->ioaddr.scr_addr + (sc_reg * 8))); +} + +static void qs_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val) +{ + if (sc_reg > SCR_CONTROL) + return; + writel(val, (void __iomem *)(ap->ioaddr.scr_addr + (sc_reg * 8))); +} + +static unsigned int qs_fill_sg(struct ata_queued_cmd *qc) +{ + struct scatterlist *sg; + struct ata_port *ap = qc->ap; + struct qs_port_priv *pp = ap->private_data; + unsigned int nelem; + u8 *prd = pp->pkt + QS_CPB_BYTES; + + WARN_ON(qc->__sg == NULL); + WARN_ON(qc->n_elem == 0 && qc->pad_len == 0); + + nelem = 0; + ata_for_each_sg(sg, qc) { + u64 addr; + u32 len; + + addr = sg_dma_address(sg); + *(__le64 *)prd = cpu_to_le64(addr); + prd += sizeof(u64); + + len = sg_dma_len(sg); + *(__le32 *)prd = cpu_to_le32(len); + prd += sizeof(u64); + + VPRINTK("PRD[%u] = (0x%llX, 0x%X)\n", nelem, + (unsigned long long)addr, len); + nelem++; + } + + return nelem; +} + +static void qs_qc_prep(struct ata_queued_cmd *qc) +{ + struct qs_port_priv *pp = qc->ap->private_data; + u8 dflags = QS_DF_PORD, *buf = pp->pkt; + u8 hflags = QS_HF_DAT | QS_HF_IEN | QS_HF_VLD; + u64 addr; + unsigned int nelem; + + VPRINTK("ENTER\n"); + + qs_enter_reg_mode(qc->ap); + if (qc->tf.protocol != ATA_PROT_DMA) { + ata_qc_prep(qc); + return; + } + + nelem = qs_fill_sg(qc); + + if ((qc->tf.flags & ATA_TFLAG_WRITE)) + hflags |= QS_HF_DIRO; + if ((qc->tf.flags & ATA_TFLAG_LBA48)) + dflags |= QS_DF_ELBA; + + /* host control block (HCB) */ + buf[ 0] = QS_HCB_HDR; + buf[ 1] = hflags; + *(__le32 *)(&buf[ 4]) = cpu_to_le32(qc->nsect * ATA_SECT_SIZE); + *(__le32 *)(&buf[ 8]) = cpu_to_le32(nelem); + addr = ((u64)pp->pkt_dma) + QS_CPB_BYTES; + *(__le64 *)(&buf[16]) = cpu_to_le64(addr); + + /* device control block (DCB) */ + buf[24] = QS_DCB_HDR; + buf[28] = dflags; + + /* frame information structure (FIS) */ + ata_tf_to_fis(&qc->tf, &buf[32], 0); +} + +static inline void qs_packet_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + u8 __iomem *chan = ap->host->mmio_base + (ap->port_no * 0x4000); + + VPRINTK("ENTER, ap %p\n", ap); + + writeb(QS_CTR0_CLER, chan + QS_CCT_CTR0); + wmb(); /* flush PRDs and pkt to memory */ + writel(QS_CCF_RUN_PKT, chan + QS_CCT_CFF); + readl(chan + QS_CCT_CFF); /* flush */ +} + +static unsigned int qs_qc_issue(struct ata_queued_cmd *qc) +{ + struct qs_port_priv *pp = qc->ap->private_data; + + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + + pp->state = qs_state_pkt; + qs_packet_start(qc); + return 0; + + case ATA_PROT_ATAPI_DMA: + BUG(); + break; + + default: + break; + } + + pp->state = qs_state_mmio; + return ata_qc_issue_prot(qc); +} + +static inline unsigned int qs_intr_pkt(struct ata_host *host) +{ + unsigned int handled = 0; + u8 sFFE; + u8 __iomem *mmio_base = host->mmio_base; + + do { + u32 sff0 = readl(mmio_base + QS_HST_SFF); + u32 sff1 = readl(mmio_base + QS_HST_SFF + 4); + u8 sEVLD = (sff1 >> 30) & 0x01; /* valid flag */ + sFFE = sff1 >> 31; /* empty flag */ + + if (sEVLD) { + u8 sDST = sff0 >> 16; /* dev status */ + u8 sHST = sff1 & 0x3f; /* host status */ + unsigned int port_no = (sff1 >> 8) & 0x03; + struct ata_port *ap = host->ports[port_no]; + + DPRINTK("SFF=%08x%08x: sCHAN=%u sHST=%d sDST=%02x\n", + sff1, sff0, port_no, sHST, sDST); + handled = 1; + if (ap && !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + struct qs_port_priv *pp = ap->private_data; + if (!pp || pp->state != qs_state_pkt) + continue; + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) { + switch (sHST) { + case 0: /* successful CPB */ + case 3: /* device error */ + pp->state = qs_state_idle; + qs_enter_reg_mode(qc->ap); + qc->err_mask |= ac_err_mask(sDST); + ata_qc_complete(qc); + break; + default: + break; + } + } + } + } + } while (!sFFE); + return handled; +} + +static inline unsigned int qs_intr_mmio(struct ata_host *host) +{ + unsigned int handled = 0, port_no; + + for (port_no = 0; port_no < host->n_ports; ++port_no) { + struct ata_port *ap; + ap = host->ports[port_no]; + if (ap && + !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + struct qs_port_priv *pp = ap->private_data; + if (!pp || pp->state != qs_state_mmio) + continue; + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) { + + /* check main status, clearing INTRQ */ + u8 status = ata_check_status(ap); + if ((status & ATA_BUSY)) + continue; + DPRINTK("ata%u: protocol %d (dev_stat 0x%X)\n", + ap->id, qc->tf.protocol, status); + + /* complete taskfile transaction */ + pp->state = qs_state_idle; + qc->err_mask |= ac_err_mask(status); + ata_qc_complete(qc); + handled = 1; + } + } + } + return handled; +} + +static irqreturn_t qs_intr(int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + unsigned int handled = 0; + + VPRINTK("ENTER\n"); + + spin_lock(&host->lock); + handled = qs_intr_pkt(host) | qs_intr_mmio(host); + spin_unlock(&host->lock); + + VPRINTK("EXIT\n"); + + return IRQ_RETVAL(handled); +} + +static void qs_ata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = + port->data_addr = base + 0x400; + port->error_addr = + port->feature_addr = base + 0x408; /* hob_feature = 0x409 */ + port->nsect_addr = base + 0x410; /* hob_nsect = 0x411 */ + port->lbal_addr = base + 0x418; /* hob_lbal = 0x419 */ + port->lbam_addr = base + 0x420; /* hob_lbam = 0x421 */ + port->lbah_addr = base + 0x428; /* hob_lbah = 0x429 */ + port->device_addr = base + 0x430; + port->status_addr = + port->command_addr = base + 0x438; + port->altstatus_addr = + port->ctl_addr = base + 0x440; + port->scr_addr = base + 0xc00; +} + +static int qs_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct qs_port_priv *pp; + void __iomem *mmio_base = ap->host->mmio_base; + void __iomem *chan = mmio_base + (ap->port_no * 0x4000); + u64 addr; + int rc; + + rc = ata_port_start(ap); + if (rc) + return rc; + qs_enter_reg_mode(ap); + pp = kzalloc(sizeof(*pp), GFP_KERNEL); + if (!pp) { + rc = -ENOMEM; + goto err_out; + } + pp->pkt = dma_alloc_coherent(dev, QS_PKT_BYTES, &pp->pkt_dma, + GFP_KERNEL); + if (!pp->pkt) { + rc = -ENOMEM; + goto err_out_kfree; + } + memset(pp->pkt, 0, QS_PKT_BYTES); + ap->private_data = pp; + + addr = (u64)pp->pkt_dma; + writel((u32) addr, chan + QS_CCF_CPBA); + writel((u32)(addr >> 32), chan + QS_CCF_CPBA + 4); + return 0; + +err_out_kfree: + kfree(pp); +err_out: + ata_port_stop(ap); + return rc; +} + +static void qs_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct qs_port_priv *pp = ap->private_data; + + if (pp != NULL) { + ap->private_data = NULL; + if (pp->pkt != NULL) + dma_free_coherent(dev, QS_PKT_BYTES, pp->pkt, + pp->pkt_dma); + kfree(pp); + } + ata_port_stop(ap); +} + +static void qs_host_stop(struct ata_host *host) +{ + void __iomem *mmio_base = host->mmio_base; + struct pci_dev *pdev = to_pci_dev(host->dev); + + writeb(0, mmio_base + QS_HCT_CTRL); /* disable host interrupts */ + writeb(QS_CNFG3_GSRST, mmio_base + QS_HCF_CNFG3); /* global reset */ + + pci_iounmap(pdev, mmio_base); +} + +static void qs_host_init(unsigned int chip_id, struct ata_probe_ent *pe) +{ + void __iomem *mmio_base = pe->mmio_base; + unsigned int port_no; + + writeb(0, mmio_base + QS_HCT_CTRL); /* disable host interrupts */ + writeb(QS_CNFG3_GSRST, mmio_base + QS_HCF_CNFG3); /* global reset */ + + /* reset each channel in turn */ + for (port_no = 0; port_no < pe->n_ports; ++port_no) { + u8 __iomem *chan = mmio_base + (port_no * 0x4000); + writeb(QS_CTR1_RDEV|QS_CTR1_RCHN, chan + QS_CCT_CTR1); + writeb(QS_CTR0_REG, chan + QS_CCT_CTR0); + readb(chan + QS_CCT_CTR0); /* flush */ + } + writeb(QS_SERD3_PHY_ENA, mmio_base + QS_HVS_SERD3); /* enable phy */ + + for (port_no = 0; port_no < pe->n_ports; ++port_no) { + u8 __iomem *chan = mmio_base + (port_no * 0x4000); + /* set FIFO depths to same settings as Windows driver */ + writew(32, chan + QS_CFC_HUFT); + writew(32, chan + QS_CFC_HDFT); + writew(10, chan + QS_CFC_DUFT); + writew( 8, chan + QS_CFC_DDFT); + /* set CPB size in bytes, as a power of two */ + writeb(QS_CPB_ORDER, chan + QS_CCF_CSEP); + } + writeb(1, mmio_base + QS_HCT_CTRL); /* enable host interrupts */ +} + +/* + * The QStor understands 64-bit buses, and uses 64-bit fields + * for DMA pointers regardless of bus width. We just have to + * make sure our DMA masks are set appropriately for whatever + * bridge lies between us and the QStor, and then the DMA mapping + * code will ensure we only ever "see" appropriate buffer addresses. + * If we're 32-bit limited somewhere, then our 64-bit fields will + * just end up with zeros in the upper 32-bits, without any special + * logic required outside of this routine (below). + */ +static int qs_set_dma_masks(struct pci_dev *pdev, void __iomem *mmio_base) +{ + u32 bus_info = readl(mmio_base + QS_HID_HPHY); + int rc, have_64bit_bus = (bus_info & QS_HPHY_64BIT); + + if (have_64bit_bus && + !pci_set_dma_mask(pdev, DMA_64BIT_MASK)) { + rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK); + if (rc) { + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "64-bit DMA enable failed\n"); + return rc; + } + } + } else { + rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit DMA enable failed\n"); + return rc; + } + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit consistent DMA enable failed\n"); + return rc; + } + } + return 0; +} + +static int qs_ata_init_one(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + void __iomem *mmio_base; + unsigned int board_idx = (unsigned int) ent->driver_data; + int rc, port_no; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto err_out; + + if ((pci_resource_flags(pdev, 4) & IORESOURCE_MEM) == 0) { + rc = -ENODEV; + goto err_out_regions; + } + + mmio_base = pci_iomap(pdev, 4, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + rc = qs_set_dma_masks(pdev, mmio_base); + if (rc) + goto err_out_iounmap; + + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_iounmap; + } + + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + probe_ent->sht = qs_port_info[board_idx].sht; + probe_ent->port_flags = qs_port_info[board_idx].flags; + probe_ent->pio_mask = qs_port_info[board_idx].pio_mask; + probe_ent->mwdma_mask = qs_port_info[board_idx].mwdma_mask; + probe_ent->udma_mask = qs_port_info[board_idx].udma_mask; + probe_ent->port_ops = qs_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + probe_ent->n_ports = QS_PORTS; + + for (port_no = 0; port_no < probe_ent->n_ports; ++port_no) { + unsigned long chan = (unsigned long)mmio_base + + (port_no * 0x4000); + qs_ata_setup_port(&probe_ent->port[port_no], chan); + } + + pci_set_master(pdev); + + /* initialize adapter */ + qs_host_init(board_idx, probe_ent); + + rc = ata_device_add(probe_ent); + kfree(probe_ent); + if (rc != QS_PORTS) + goto err_out_iounmap; + return 0; + +err_out_iounmap: + pci_iounmap(pdev, mmio_base); +err_out_regions: + pci_release_regions(pdev); +err_out: + pci_disable_device(pdev); + return rc; +} + +static int __init qs_ata_init(void) +{ + return pci_register_driver(&qs_ata_pci_driver); +} + +static void __exit qs_ata_exit(void) +{ + pci_unregister_driver(&qs_ata_pci_driver); +} + +MODULE_AUTHOR("Mark Lord"); +MODULE_DESCRIPTION("Pacific Digital Corporation QStor SATA low-level driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, qs_ata_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_init(qs_ata_init); +module_exit(qs_ata_exit); diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c new file mode 100644 index 00000000000..c63dbabc0cd --- /dev/null +++ b/drivers/ata/sata_sil.c @@ -0,0 +1,728 @@ +/* + * sata_sil.c - Silicon Image SATA + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2003-2005 Red Hat, Inc. + * Copyright 2003 Benjamin Herrenschmidt + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Documentation for SiI 3112: + * http://gkernel.sourceforge.net/specs/sii/3112A_SiI-DS-0095-B2.pdf.bz2 + * + * Other errata and documentation available under NDA. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "sata_sil" +#define DRV_VERSION "2.0" + +enum { + /* + * host flags + */ + SIL_FLAG_NO_SATA_IRQ = (1 << 28), + SIL_FLAG_RERR_ON_DMA_ACT = (1 << 29), + SIL_FLAG_MOD15WRITE = (1 << 30), + + SIL_DFL_PORT_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO | ATA_FLAG_HRST_TO_RESUME, + + /* + * Controller IDs + */ + sil_3112 = 0, + sil_3112_no_sata_irq = 1, + sil_3512 = 2, + sil_3114 = 3, + + /* + * Register offsets + */ + SIL_SYSCFG = 0x48, + + /* + * Register bits + */ + /* SYSCFG */ + SIL_MASK_IDE0_INT = (1 << 22), + SIL_MASK_IDE1_INT = (1 << 23), + SIL_MASK_IDE2_INT = (1 << 24), + SIL_MASK_IDE3_INT = (1 << 25), + SIL_MASK_2PORT = SIL_MASK_IDE0_INT | SIL_MASK_IDE1_INT, + SIL_MASK_4PORT = SIL_MASK_2PORT | + SIL_MASK_IDE2_INT | SIL_MASK_IDE3_INT, + + /* BMDMA/BMDMA2 */ + SIL_INTR_STEERING = (1 << 1), + + SIL_DMA_ENABLE = (1 << 0), /* DMA run switch */ + SIL_DMA_RDWR = (1 << 3), /* DMA Rd-Wr */ + SIL_DMA_SATA_IRQ = (1 << 4), /* OR of all SATA IRQs */ + SIL_DMA_ACTIVE = (1 << 16), /* DMA running */ + SIL_DMA_ERROR = (1 << 17), /* PCI bus error */ + SIL_DMA_COMPLETE = (1 << 18), /* cmd complete / IRQ pending */ + SIL_DMA_N_SATA_IRQ = (1 << 6), /* SATA_IRQ for the next channel */ + SIL_DMA_N_ACTIVE = (1 << 24), /* ACTIVE for the next channel */ + SIL_DMA_N_ERROR = (1 << 25), /* ERROR for the next channel */ + SIL_DMA_N_COMPLETE = (1 << 26), /* COMPLETE for the next channel */ + + /* SIEN */ + SIL_SIEN_N = (1 << 16), /* triggered by SError.N */ + + /* + * Others + */ + SIL_QUIRK_MOD15WRITE = (1 << 0), + SIL_QUIRK_UDMA5MAX = (1 << 1), +}; + +static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +#ifdef CONFIG_PM +static int sil_pci_device_resume(struct pci_dev *pdev); +#endif +static void sil_dev_config(struct ata_port *ap, struct ata_device *dev); +static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); +static void sil_post_set_mode (struct ata_port *ap); +static irqreturn_t sil_interrupt(int irq, void *dev_instance, + struct pt_regs *regs); +static void sil_freeze(struct ata_port *ap); +static void sil_thaw(struct ata_port *ap); + + +static const struct pci_device_id sil_pci_tbl[] = { + { 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 }, + { 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 }, + { 0x1095, 0x3512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3512 }, + { 0x1095, 0x3114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3114 }, + { 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 }, + { 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_no_sata_irq }, + { 0x1002, 0x437a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_no_sata_irq }, + { } /* terminate list */ +}; + + +/* TODO firmware versions should be added - eric */ +static const struct sil_drivelist { + const char * product; + unsigned int quirk; +} sil_blacklist [] = { + { "ST320012AS", SIL_QUIRK_MOD15WRITE }, + { "ST330013AS", SIL_QUIRK_MOD15WRITE }, + { "ST340017AS", SIL_QUIRK_MOD15WRITE }, + { "ST360015AS", SIL_QUIRK_MOD15WRITE }, + { "ST380023AS", SIL_QUIRK_MOD15WRITE }, + { "ST3120023AS", SIL_QUIRK_MOD15WRITE }, + { "ST340014ASL", SIL_QUIRK_MOD15WRITE }, + { "ST360014ASL", SIL_QUIRK_MOD15WRITE }, + { "ST380011ASL", SIL_QUIRK_MOD15WRITE }, + { "ST3120022ASL", SIL_QUIRK_MOD15WRITE }, + { "ST3160021ASL", SIL_QUIRK_MOD15WRITE }, + { "Maxtor 4D060H3", SIL_QUIRK_UDMA5MAX }, + { } +}; + +static struct pci_driver sil_pci_driver = { + .name = DRV_NAME, + .id_table = sil_pci_tbl, + .probe = sil_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM + .suspend = ata_pci_device_suspend, + .resume = sil_pci_device_resume, +#endif +}; + +static struct scsi_host_template sil_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, + .suspend = ata_scsi_device_suspend, + .resume = ata_scsi_device_resume, +}; + +static const struct ata_port_operations sil_ops = { + .port_disable = ata_port_disable, + .dev_config = sil_dev_config, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .post_set_mode = sil_post_set_mode, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + .freeze = sil_freeze, + .thaw = sil_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .irq_handler = sil_interrupt, + .irq_clear = ata_bmdma_irq_clear, + .scr_read = sil_scr_read, + .scr_write = sil_scr_write, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static const struct ata_port_info sil_port_info[] = { + /* sil_3112 */ + { + .sht = &sil_sht, + .flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_MOD15WRITE, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil_ops, + }, + /* sil_3112_no_sata_irq */ + { + .sht = &sil_sht, + .flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_MOD15WRITE | + SIL_FLAG_NO_SATA_IRQ, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil_ops, + }, + /* sil_3512 */ + { + .sht = &sil_sht, + .flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil_ops, + }, + /* sil_3114 */ + { + .sht = &sil_sht, + .flags = SIL_DFL_PORT_FLAGS | SIL_FLAG_RERR_ON_DMA_ACT, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil_ops, + }, +}; + +/* per-port register offsets */ +/* TODO: we can probably calculate rather than use a table */ +static const struct { + unsigned long tf; /* ATA taskfile register block */ + unsigned long ctl; /* ATA control/altstatus register block */ + unsigned long bmdma; /* DMA register block */ + unsigned long bmdma2; /* DMA register block #2 */ + unsigned long fifo_cfg; /* FIFO Valid Byte Count and Control */ + unsigned long scr; /* SATA control register block */ + unsigned long sien; /* SATA Interrupt Enable register */ + unsigned long xfer_mode;/* data transfer mode register */ + unsigned long sfis_cfg; /* SATA FIS reception config register */ +} sil_port[] = { + /* port 0 ... */ + { 0x80, 0x8A, 0x00, 0x10, 0x40, 0x100, 0x148, 0xb4, 0x14c }, + { 0xC0, 0xCA, 0x08, 0x18, 0x44, 0x180, 0x1c8, 0xf4, 0x1cc }, + { 0x280, 0x28A, 0x200, 0x210, 0x240, 0x300, 0x348, 0x2b4, 0x34c }, + { 0x2C0, 0x2CA, 0x208, 0x218, 0x244, 0x380, 0x3c8, 0x2f4, 0x3cc }, + /* ... port 3 */ +}; + +MODULE_AUTHOR("Jeff Garzik"); +MODULE_DESCRIPTION("low-level driver for Silicon Image SATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sil_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +static int slow_down = 0; +module_param(slow_down, int, 0444); +MODULE_PARM_DESC(slow_down, "Sledgehammer used to work around random problems, by limiting commands to 15 sectors (0=off, 1=on)"); + + +static unsigned char sil_get_device_cache_line(struct pci_dev *pdev) +{ + u8 cache_line = 0; + pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &cache_line); + return cache_line; +} + +static void sil_post_set_mode (struct ata_port *ap) +{ + struct ata_host *host = ap->host; + struct ata_device *dev; + void __iomem *addr = host->mmio_base + sil_port[ap->port_no].xfer_mode; + u32 tmp, dev_mode[2]; + unsigned int i; + + for (i = 0; i < 2; i++) { + dev = &ap->device[i]; + if (!ata_dev_enabled(dev)) + dev_mode[i] = 0; /* PIO0/1/2 */ + else if (dev->flags & ATA_DFLAG_PIO) + dev_mode[i] = 1; /* PIO3/4 */ + else + dev_mode[i] = 3; /* UDMA */ + /* value 2 indicates MDMA */ + } + + tmp = readl(addr); + tmp &= ~((1<<5) | (1<<4) | (1<<1) | (1<<0)); + tmp |= dev_mode[0]; + tmp |= (dev_mode[1] << 4); + writel(tmp, addr); + readl(addr); /* flush */ +} + +static inline unsigned long sil_scr_addr(struct ata_port *ap, unsigned int sc_reg) +{ + unsigned long offset = ap->ioaddr.scr_addr; + + switch (sc_reg) { + case SCR_STATUS: + return offset + 4; + case SCR_ERROR: + return offset + 8; + case SCR_CONTROL: + return offset; + default: + /* do nothing */ + break; + } + + return 0; +} + +static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + void __iomem *mmio = (void __iomem *) sil_scr_addr(ap, sc_reg); + if (mmio) + return readl(mmio); + return 0xffffffffU; +} + +static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val) +{ + void *mmio = (void __iomem *) sil_scr_addr(ap, sc_reg); + if (mmio) + writel(val, mmio); +} + +static void sil_host_intr(struct ata_port *ap, u32 bmdma2) +{ + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag); + u8 status; + + if (unlikely(bmdma2 & SIL_DMA_SATA_IRQ)) { + u32 serror; + + /* SIEN doesn't mask SATA IRQs on some 3112s. Those + * controllers continue to assert IRQ as long as + * SError bits are pending. Clear SError immediately. + */ + serror = sil_scr_read(ap, SCR_ERROR); + sil_scr_write(ap, SCR_ERROR, serror); + + /* Trigger hotplug and accumulate SError only if the + * port isn't already frozen. Otherwise, PHY events + * during hardreset makes controllers with broken SIEN + * repeat probing needlessly. + */ + if (!(ap->pflags & ATA_PFLAG_FROZEN)) { + ata_ehi_hotplugged(&ap->eh_info); + ap->eh_info.serror |= serror; + } + + goto freeze; + } + + if (unlikely(!qc || qc->tf.ctl & ATA_NIEN)) + goto freeze; + + /* Check whether we are expecting interrupt in this state */ + switch (ap->hsm_task_state) { + case HSM_ST_FIRST: + /* Some pre-ATAPI-4 devices assert INTRQ + * at this state when ready to receive CDB. + */ + + /* Check the ATA_DFLAG_CDB_INTR flag is enough here. + * The flag was turned on only for atapi devices. + * No need to check is_atapi_taskfile(&qc->tf) again. + */ + if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) + goto err_hsm; + break; + case HSM_ST_LAST: + if (qc->tf.protocol == ATA_PROT_DMA || + qc->tf.protocol == ATA_PROT_ATAPI_DMA) { + /* clear DMA-Start bit */ + ap->ops->bmdma_stop(qc); + + if (bmdma2 & SIL_DMA_ERROR) { + qc->err_mask |= AC_ERR_HOST_BUS; + ap->hsm_task_state = HSM_ST_ERR; + } + } + break; + case HSM_ST: + break; + default: + goto err_hsm; + } + + /* check main status, clearing INTRQ */ + status = ata_chk_status(ap); + if (unlikely(status & ATA_BUSY)) + goto err_hsm; + + /* ack bmdma irq events */ + ata_bmdma_irq_clear(ap); + + /* kick HSM in the ass */ + ata_hsm_move(ap, qc, status, 0); + + return; + + err_hsm: + qc->err_mask |= AC_ERR_HSM; + freeze: + ata_port_freeze(ap); +} + +static irqreturn_t sil_interrupt(int irq, void *dev_instance, + struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + void __iomem *mmio_base = host->mmio_base; + int handled = 0; + int i; + + spin_lock(&host->lock); + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap = host->ports[i]; + u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2); + + if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED)) + continue; + + /* turn off SATA_IRQ if not supported */ + if (ap->flags & SIL_FLAG_NO_SATA_IRQ) + bmdma2 &= ~SIL_DMA_SATA_IRQ; + + if (bmdma2 == 0xffffffff || + !(bmdma2 & (SIL_DMA_COMPLETE | SIL_DMA_SATA_IRQ))) + continue; + + sil_host_intr(ap, bmdma2); + handled = 1; + } + + spin_unlock(&host->lock); + + return IRQ_RETVAL(handled); +} + +static void sil_freeze(struct ata_port *ap) +{ + void __iomem *mmio_base = ap->host->mmio_base; + u32 tmp; + + /* global IRQ mask doesn't block SATA IRQ, turn off explicitly */ + writel(0, mmio_base + sil_port[ap->port_no].sien); + + /* plug IRQ */ + tmp = readl(mmio_base + SIL_SYSCFG); + tmp |= SIL_MASK_IDE0_INT << ap->port_no; + writel(tmp, mmio_base + SIL_SYSCFG); + readl(mmio_base + SIL_SYSCFG); /* flush */ +} + +static void sil_thaw(struct ata_port *ap) +{ + void __iomem *mmio_base = ap->host->mmio_base; + u32 tmp; + + /* clear IRQ */ + ata_chk_status(ap); + ata_bmdma_irq_clear(ap); + + /* turn on SATA IRQ if supported */ + if (!(ap->flags & SIL_FLAG_NO_SATA_IRQ)) + writel(SIL_SIEN_N, mmio_base + sil_port[ap->port_no].sien); + + /* turn on IRQ */ + tmp = readl(mmio_base + SIL_SYSCFG); + tmp &= ~(SIL_MASK_IDE0_INT << ap->port_no); + writel(tmp, mmio_base + SIL_SYSCFG); +} + +/** + * sil_dev_config - Apply device/host-specific errata fixups + * @ap: Port containing device to be examined + * @dev: Device to be examined + * + * After the IDENTIFY [PACKET] DEVICE step is complete, and a + * device is known to be present, this function is called. + * We apply two errata fixups which are specific to Silicon Image, + * a Seagate and a Maxtor fixup. + * + * For certain Seagate devices, we must limit the maximum sectors + * to under 8K. + * + * For certain Maxtor devices, we must not program the drive + * beyond udma5. + * + * Both fixups are unfairly pessimistic. As soon as I get more + * information on these errata, I will create a more exhaustive + * list, and apply the fixups to only the specific + * devices/hosts/firmwares that need it. + * + * 20040111 - Seagate drives affected by the Mod15Write bug are blacklisted + * The Maxtor quirk is in the blacklist, but I'm keeping the original + * pessimistic fix for the following reasons... + * - There seems to be less info on it, only one device gleaned off the + * Windows driver, maybe only one is affected. More info would be greatly + * appreciated. + * - But then again UDMA5 is hardly anything to complain about + */ +static void sil_dev_config(struct ata_port *ap, struct ata_device *dev) +{ + unsigned int n, quirks = 0; + unsigned char model_num[41]; + + ata_id_c_string(dev->id, model_num, ATA_ID_PROD_OFS, sizeof(model_num)); + + for (n = 0; sil_blacklist[n].product; n++) + if (!strcmp(sil_blacklist[n].product, model_num)) { + quirks = sil_blacklist[n].quirk; + break; + } + + /* limit requests to 15 sectors */ + if (slow_down || + ((ap->flags & SIL_FLAG_MOD15WRITE) && + (quirks & SIL_QUIRK_MOD15WRITE))) { + ata_dev_printk(dev, KERN_INFO, "applying Seagate errata fix " + "(mod15write workaround)\n"); + dev->max_sectors = 15; + return; + } + + /* limit to udma5 */ + if (quirks & SIL_QUIRK_UDMA5MAX) { + ata_dev_printk(dev, KERN_INFO, + "applying Maxtor errata fix %s\n", model_num); + dev->udma_mask &= ATA_UDMA5; + return; + } +} + +static void sil_init_controller(struct pci_dev *pdev, + int n_ports, unsigned long port_flags, + void __iomem *mmio_base) +{ + u8 cls; + u32 tmp; + int i; + + /* Initialize FIFO PCI bus arbitration */ + cls = sil_get_device_cache_line(pdev); + if (cls) { + cls >>= 3; + cls++; /* cls = (line_size/8)+1 */ + for (i = 0; i < n_ports; i++) + writew(cls << 8 | cls, + mmio_base + sil_port[i].fifo_cfg); + } else + dev_printk(KERN_WARNING, &pdev->dev, + "cache line size not set. Driver may not function\n"); + + /* Apply R_ERR on DMA activate FIS errata workaround */ + if (port_flags & SIL_FLAG_RERR_ON_DMA_ACT) { + int cnt; + + for (i = 0, cnt = 0; i < n_ports; i++) { + tmp = readl(mmio_base + sil_port[i].sfis_cfg); + if ((tmp & 0x3) != 0x01) + continue; + if (!cnt) + dev_printk(KERN_INFO, &pdev->dev, + "Applying R_ERR on DMA activate " + "FIS errata fix\n"); + writel(tmp & ~0x3, mmio_base + sil_port[i].sfis_cfg); + cnt++; + } + } + + if (n_ports == 4) { + /* flip the magic "make 4 ports work" bit */ + tmp = readl(mmio_base + sil_port[2].bmdma); + if ((tmp & SIL_INTR_STEERING) == 0) + writel(tmp | SIL_INTR_STEERING, + mmio_base + sil_port[2].bmdma); + } +} + +static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + unsigned long base; + void __iomem *mmio_base; + int rc; + unsigned int i; + int pci_dev_busy = 0; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + INIT_LIST_HEAD(&probe_ent->node); + probe_ent->dev = pci_dev_to_dev(pdev); + probe_ent->port_ops = sil_port_info[ent->driver_data].port_ops; + probe_ent->sht = sil_port_info[ent->driver_data].sht; + probe_ent->n_ports = (ent->driver_data == sil_3114) ? 4 : 2; + probe_ent->pio_mask = sil_port_info[ent->driver_data].pio_mask; + probe_ent->mwdma_mask = sil_port_info[ent->driver_data].mwdma_mask; + probe_ent->udma_mask = sil_port_info[ent->driver_data].udma_mask; + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->port_flags = sil_port_info[ent->driver_data].flags; + + mmio_base = pci_iomap(pdev, 5, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + + probe_ent->mmio_base = mmio_base; + + base = (unsigned long) mmio_base; + + for (i = 0; i < probe_ent->n_ports; i++) { + probe_ent->port[i].cmd_addr = base + sil_port[i].tf; + probe_ent->port[i].altstatus_addr = + probe_ent->port[i].ctl_addr = base + sil_port[i].ctl; + probe_ent->port[i].bmdma_addr = base + sil_port[i].bmdma; + probe_ent->port[i].scr_addr = base + sil_port[i].scr; + ata_std_ports(&probe_ent->port[i]); + } + + sil_init_controller(pdev, probe_ent->n_ports, probe_ent->port_flags, + mmio_base); + + pci_set_master(pdev); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; +} + +#ifdef CONFIG_PM +static int sil_pci_device_resume(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + + ata_pci_device_do_resume(pdev); + sil_init_controller(pdev, host->n_ports, host->ports[0]->flags, + host->mmio_base); + ata_host_resume(host); + + return 0; +} +#endif + +static int __init sil_init(void) +{ + return pci_register_driver(&sil_pci_driver); +} + +static void __exit sil_exit(void) +{ + pci_unregister_driver(&sil_pci_driver); +} + + +module_init(sil_init); +module_exit(sil_exit); diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c new file mode 100644 index 00000000000..39cb07baeba --- /dev/null +++ b/drivers/ata/sata_sil24.c @@ -0,0 +1,1227 @@ +/* + * sata_sil24.c - Driver for Silicon Image 3124/3132 SATA-2 controllers + * + * Copyright 2005 Tejun Heo + * + * Based on preview driver from Silicon Image. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2, or (at your option) any + * later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/dma-mapping.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <linux/libata.h> +#include <asm/io.h> + +#define DRV_NAME "sata_sil24" +#define DRV_VERSION "0.3" + +/* + * Port request block (PRB) 32 bytes + */ +struct sil24_prb { + __le16 ctrl; + __le16 prot; + __le32 rx_cnt; + u8 fis[6 * 4]; +}; + +/* + * Scatter gather entry (SGE) 16 bytes + */ +struct sil24_sge { + __le64 addr; + __le32 cnt; + __le32 flags; +}; + +/* + * Port multiplier + */ +struct sil24_port_multiplier { + __le32 diag; + __le32 sactive; +}; + +enum { + /* + * Global controller registers (128 bytes @ BAR0) + */ + /* 32 bit regs */ + HOST_SLOT_STAT = 0x00, /* 32 bit slot stat * 4 */ + HOST_CTRL = 0x40, + HOST_IRQ_STAT = 0x44, + HOST_PHY_CFG = 0x48, + HOST_BIST_CTRL = 0x50, + HOST_BIST_PTRN = 0x54, + HOST_BIST_STAT = 0x58, + HOST_MEM_BIST_STAT = 0x5c, + HOST_FLASH_CMD = 0x70, + /* 8 bit regs */ + HOST_FLASH_DATA = 0x74, + HOST_TRANSITION_DETECT = 0x75, + HOST_GPIO_CTRL = 0x76, + HOST_I2C_ADDR = 0x78, /* 32 bit */ + HOST_I2C_DATA = 0x7c, + HOST_I2C_XFER_CNT = 0x7e, + HOST_I2C_CTRL = 0x7f, + + /* HOST_SLOT_STAT bits */ + HOST_SSTAT_ATTN = (1 << 31), + + /* HOST_CTRL bits */ + HOST_CTRL_M66EN = (1 << 16), /* M66EN PCI bus signal */ + HOST_CTRL_TRDY = (1 << 17), /* latched PCI TRDY */ + HOST_CTRL_STOP = (1 << 18), /* latched PCI STOP */ + HOST_CTRL_DEVSEL = (1 << 19), /* latched PCI DEVSEL */ + HOST_CTRL_REQ64 = (1 << 20), /* latched PCI REQ64 */ + HOST_CTRL_GLOBAL_RST = (1 << 31), /* global reset */ + + /* + * Port registers + * (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2) + */ + PORT_REGS_SIZE = 0x2000, + + PORT_LRAM = 0x0000, /* 31 LRAM slots and PM regs */ + PORT_LRAM_SLOT_SZ = 0x0080, /* 32 bytes PRB + 2 SGE, ACT... */ + + PORT_PM = 0x0f80, /* 8 bytes PM * 16 (128 bytes) */ + /* 32 bit regs */ + PORT_CTRL_STAT = 0x1000, /* write: ctrl-set, read: stat */ + PORT_CTRL_CLR = 0x1004, /* write: ctrl-clear */ + PORT_IRQ_STAT = 0x1008, /* high: status, low: interrupt */ + PORT_IRQ_ENABLE_SET = 0x1010, /* write: enable-set */ + PORT_IRQ_ENABLE_CLR = 0x1014, /* write: enable-clear */ + PORT_ACTIVATE_UPPER_ADDR= 0x101c, + PORT_EXEC_FIFO = 0x1020, /* command execution fifo */ + PORT_CMD_ERR = 0x1024, /* command error number */ + PORT_FIS_CFG = 0x1028, + PORT_FIFO_THRES = 0x102c, + /* 16 bit regs */ + PORT_DECODE_ERR_CNT = 0x1040, + PORT_DECODE_ERR_THRESH = 0x1042, + PORT_CRC_ERR_CNT = 0x1044, + PORT_CRC_ERR_THRESH = 0x1046, + PORT_HSHK_ERR_CNT = 0x1048, + PORT_HSHK_ERR_THRESH = 0x104a, + /* 32 bit regs */ + PORT_PHY_CFG = 0x1050, + PORT_SLOT_STAT = 0x1800, + PORT_CMD_ACTIVATE = 0x1c00, /* 64 bit cmd activate * 31 (248 bytes) */ + PORT_EXEC_DIAG = 0x1e00, /* 32bit exec diag * 16 (64 bytes, 0-10 used on 3124) */ + PORT_PSD_DIAG = 0x1e40, /* 32bit psd diag * 16 (64 bytes, 0-8 used on 3124) */ + PORT_SCONTROL = 0x1f00, + PORT_SSTATUS = 0x1f04, + PORT_SERROR = 0x1f08, + PORT_SACTIVE = 0x1f0c, + + /* PORT_CTRL_STAT bits */ + PORT_CS_PORT_RST = (1 << 0), /* port reset */ + PORT_CS_DEV_RST = (1 << 1), /* device reset */ + PORT_CS_INIT = (1 << 2), /* port initialize */ + PORT_CS_IRQ_WOC = (1 << 3), /* interrupt write one to clear */ + PORT_CS_CDB16 = (1 << 5), /* 0=12b cdb, 1=16b cdb */ + PORT_CS_RESUME = (1 << 6), /* port resume */ + PORT_CS_32BIT_ACTV = (1 << 10), /* 32-bit activation */ + PORT_CS_PM_EN = (1 << 13), /* port multiplier enable */ + PORT_CS_RDY = (1 << 31), /* port ready to accept commands */ + + /* PORT_IRQ_STAT/ENABLE_SET/CLR */ + /* bits[11:0] are masked */ + PORT_IRQ_COMPLETE = (1 << 0), /* command(s) completed */ + PORT_IRQ_ERROR = (1 << 1), /* command execution error */ + PORT_IRQ_PORTRDY_CHG = (1 << 2), /* port ready change */ + PORT_IRQ_PWR_CHG = (1 << 3), /* power management change */ + PORT_IRQ_PHYRDY_CHG = (1 << 4), /* PHY ready change */ + PORT_IRQ_COMWAKE = (1 << 5), /* COMWAKE received */ + PORT_IRQ_UNK_FIS = (1 << 6), /* unknown FIS received */ + PORT_IRQ_DEV_XCHG = (1 << 7), /* device exchanged */ + PORT_IRQ_8B10B = (1 << 8), /* 8b/10b decode error threshold */ + PORT_IRQ_CRC = (1 << 9), /* CRC error threshold */ + PORT_IRQ_HANDSHAKE = (1 << 10), /* handshake error threshold */ + PORT_IRQ_SDB_NOTIFY = (1 << 11), /* SDB notify received */ + + DEF_PORT_IRQ = PORT_IRQ_COMPLETE | PORT_IRQ_ERROR | + PORT_IRQ_PHYRDY_CHG | PORT_IRQ_DEV_XCHG | + PORT_IRQ_UNK_FIS, + + /* bits[27:16] are unmasked (raw) */ + PORT_IRQ_RAW_SHIFT = 16, + PORT_IRQ_MASKED_MASK = 0x7ff, + PORT_IRQ_RAW_MASK = (0x7ff << PORT_IRQ_RAW_SHIFT), + + /* ENABLE_SET/CLR specific, intr steering - 2 bit field */ + PORT_IRQ_STEER_SHIFT = 30, + PORT_IRQ_STEER_MASK = (3 << PORT_IRQ_STEER_SHIFT), + + /* PORT_CMD_ERR constants */ + PORT_CERR_DEV = 1, /* Error bit in D2H Register FIS */ + PORT_CERR_SDB = 2, /* Error bit in SDB FIS */ + PORT_CERR_DATA = 3, /* Error in data FIS not detected by dev */ + PORT_CERR_SEND = 4, /* Initial cmd FIS transmission failure */ + PORT_CERR_INCONSISTENT = 5, /* Protocol mismatch */ + PORT_CERR_DIRECTION = 6, /* Data direction mismatch */ + PORT_CERR_UNDERRUN = 7, /* Ran out of SGEs while writing */ + PORT_CERR_OVERRUN = 8, /* Ran out of SGEs while reading */ + PORT_CERR_PKT_PROT = 11, /* DIR invalid in 1st PIO setup of ATAPI */ + PORT_CERR_SGT_BOUNDARY = 16, /* PLD ecode 00 - SGT not on qword boundary */ + PORT_CERR_SGT_TGTABRT = 17, /* PLD ecode 01 - target abort */ + PORT_CERR_SGT_MSTABRT = 18, /* PLD ecode 10 - master abort */ + PORT_CERR_SGT_PCIPERR = 19, /* PLD ecode 11 - PCI parity err while fetching SGT */ + PORT_CERR_CMD_BOUNDARY = 24, /* ctrl[15:13] 001 - PRB not on qword boundary */ + PORT_CERR_CMD_TGTABRT = 25, /* ctrl[15:13] 010 - target abort */ + PORT_CERR_CMD_MSTABRT = 26, /* ctrl[15:13] 100 - master abort */ + PORT_CERR_CMD_PCIPERR = 27, /* ctrl[15:13] 110 - PCI parity err while fetching PRB */ + PORT_CERR_XFR_UNDEF = 32, /* PSD ecode 00 - undefined */ + PORT_CERR_XFR_TGTABRT = 33, /* PSD ecode 01 - target abort */ + PORT_CERR_XFR_MSTABRT = 34, /* PSD ecode 10 - master abort */ + PORT_CERR_XFR_PCIPERR = 35, /* PSD ecode 11 - PCI prity err during transfer */ + PORT_CERR_SENDSERVICE = 36, /* FIS received while sending service */ + + /* bits of PRB control field */ + PRB_CTRL_PROTOCOL = (1 << 0), /* override def. ATA protocol */ + PRB_CTRL_PACKET_READ = (1 << 4), /* PACKET cmd read */ + PRB_CTRL_PACKET_WRITE = (1 << 5), /* PACKET cmd write */ + PRB_CTRL_NIEN = (1 << 6), /* Mask completion irq */ + PRB_CTRL_SRST = (1 << 7), /* Soft reset request (ign BSY?) */ + + /* PRB protocol field */ + PRB_PROT_PACKET = (1 << 0), + PRB_PROT_TCQ = (1 << 1), + PRB_PROT_NCQ = (1 << 2), + PRB_PROT_READ = (1 << 3), + PRB_PROT_WRITE = (1 << 4), + PRB_PROT_TRANSPARENT = (1 << 5), + + /* + * Other constants + */ + SGE_TRM = (1 << 31), /* Last SGE in chain */ + SGE_LNK = (1 << 30), /* linked list + Points to SGT, not SGE */ + SGE_DRD = (1 << 29), /* discard data read (/dev/null) + data address ignored */ + + SIL24_MAX_CMDS = 31, + + /* board id */ + BID_SIL3124 = 0, + BID_SIL3132 = 1, + BID_SIL3131 = 2, + + /* host flags */ + SIL24_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | + ATA_FLAG_NCQ | ATA_FLAG_SKIP_D2H_BSY, + SIL24_FLAG_PCIX_IRQ_WOC = (1 << 24), /* IRQ loss errata on PCI-X */ + + IRQ_STAT_4PORTS = 0xf, +}; + +struct sil24_ata_block { + struct sil24_prb prb; + struct sil24_sge sge[LIBATA_MAX_PRD]; +}; + +struct sil24_atapi_block { + struct sil24_prb prb; + u8 cdb[16]; + struct sil24_sge sge[LIBATA_MAX_PRD - 1]; +}; + +union sil24_cmd_block { + struct sil24_ata_block ata; + struct sil24_atapi_block atapi; +}; + +static struct sil24_cerr_info { + unsigned int err_mask, action; + const char *desc; +} sil24_cerr_db[] = { + [0] = { AC_ERR_DEV, ATA_EH_REVALIDATE, + "device error" }, + [PORT_CERR_DEV] = { AC_ERR_DEV, ATA_EH_REVALIDATE, + "device error via D2H FIS" }, + [PORT_CERR_SDB] = { AC_ERR_DEV, ATA_EH_REVALIDATE, + "device error via SDB FIS" }, + [PORT_CERR_DATA] = { AC_ERR_ATA_BUS, ATA_EH_SOFTRESET, + "error in data FIS" }, + [PORT_CERR_SEND] = { AC_ERR_ATA_BUS, ATA_EH_SOFTRESET, + "failed to transmit command FIS" }, + [PORT_CERR_INCONSISTENT] = { AC_ERR_HSM, ATA_EH_SOFTRESET, + "protocol mismatch" }, + [PORT_CERR_DIRECTION] = { AC_ERR_HSM, ATA_EH_SOFTRESET, + "data directon mismatch" }, + [PORT_CERR_UNDERRUN] = { AC_ERR_HSM, ATA_EH_SOFTRESET, + "ran out of SGEs while writing" }, + [PORT_CERR_OVERRUN] = { AC_ERR_HSM, ATA_EH_SOFTRESET, + "ran out of SGEs while reading" }, + [PORT_CERR_PKT_PROT] = { AC_ERR_HSM, ATA_EH_SOFTRESET, + "invalid data directon for ATAPI CDB" }, + [PORT_CERR_SGT_BOUNDARY] = { AC_ERR_SYSTEM, ATA_EH_SOFTRESET, + "SGT no on qword boundary" }, + [PORT_CERR_SGT_TGTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI target abort while fetching SGT" }, + [PORT_CERR_SGT_MSTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI master abort while fetching SGT" }, + [PORT_CERR_SGT_PCIPERR] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI parity error while fetching SGT" }, + [PORT_CERR_CMD_BOUNDARY] = { AC_ERR_SYSTEM, ATA_EH_SOFTRESET, + "PRB not on qword boundary" }, + [PORT_CERR_CMD_TGTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI target abort while fetching PRB" }, + [PORT_CERR_CMD_MSTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI master abort while fetching PRB" }, + [PORT_CERR_CMD_PCIPERR] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI parity error while fetching PRB" }, + [PORT_CERR_XFR_UNDEF] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "undefined error while transferring data" }, + [PORT_CERR_XFR_TGTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI target abort while transferring data" }, + [PORT_CERR_XFR_MSTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI master abort while transferring data" }, + [PORT_CERR_XFR_PCIPERR] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, + "PCI parity error while transferring data" }, + [PORT_CERR_SENDSERVICE] = { AC_ERR_HSM, ATA_EH_SOFTRESET, + "FIS received while sending service FIS" }, +}; + +/* + * ap->private_data + * + * The preview driver always returned 0 for status. We emulate it + * here from the previous interrupt. + */ +struct sil24_port_priv { + union sil24_cmd_block *cmd_block; /* 32 cmd blocks */ + dma_addr_t cmd_block_dma; /* DMA base addr for them */ + struct ata_taskfile tf; /* Cached taskfile registers */ +}; + +/* ap->host->private_data */ +struct sil24_host_priv { + void __iomem *host_base; /* global controller control (128 bytes @BAR0) */ + void __iomem *port_base; /* port registers (4 * 8192 bytes @BAR2) */ +}; + +static void sil24_dev_config(struct ata_port *ap, struct ata_device *dev); +static u8 sil24_check_status(struct ata_port *ap); +static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg); +static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val); +static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf); +static void sil24_qc_prep(struct ata_queued_cmd *qc); +static unsigned int sil24_qc_issue(struct ata_queued_cmd *qc); +static void sil24_irq_clear(struct ata_port *ap); +static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs); +static void sil24_freeze(struct ata_port *ap); +static void sil24_thaw(struct ata_port *ap); +static void sil24_error_handler(struct ata_port *ap); +static void sil24_post_internal_cmd(struct ata_queued_cmd *qc); +static int sil24_port_start(struct ata_port *ap); +static void sil24_port_stop(struct ata_port *ap); +static void sil24_host_stop(struct ata_host *host); +static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); +#ifdef CONFIG_PM +static int sil24_pci_device_resume(struct pci_dev *pdev); +#endif + +static const struct pci_device_id sil24_pci_tbl[] = { + { 0x1095, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 }, + { 0x8086, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 }, + { 0x1095, 0x3132, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3132 }, + { 0x1095, 0x3131, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3131 }, + { 0x1095, 0x3531, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3131 }, + { } /* terminate list */ +}; + +static struct pci_driver sil24_pci_driver = { + .name = DRV_NAME, + .id_table = sil24_pci_tbl, + .probe = sil24_init_one, + .remove = ata_pci_remove_one, /* safe? */ +#ifdef CONFIG_PM + .suspend = ata_pci_device_suspend, + .resume = sil24_pci_device_resume, +#endif +}; + +static struct scsi_host_template sil24_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .change_queue_depth = ata_scsi_change_queue_depth, + .can_queue = SIL24_MAX_CMDS, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, + .suspend = ata_scsi_device_suspend, + .resume = ata_scsi_device_resume, +}; + +static const struct ata_port_operations sil24_ops = { + .port_disable = ata_port_disable, + + .dev_config = sil24_dev_config, + + .check_status = sil24_check_status, + .check_altstatus = sil24_check_status, + .dev_select = ata_noop_dev_select, + + .tf_read = sil24_tf_read, + + .qc_prep = sil24_qc_prep, + .qc_issue = sil24_qc_issue, + + .irq_handler = sil24_interrupt, + .irq_clear = sil24_irq_clear, + + .scr_read = sil24_scr_read, + .scr_write = sil24_scr_write, + + .freeze = sil24_freeze, + .thaw = sil24_thaw, + .error_handler = sil24_error_handler, + .post_internal_cmd = sil24_post_internal_cmd, + + .port_start = sil24_port_start, + .port_stop = sil24_port_stop, + .host_stop = sil24_host_stop, +}; + +/* + * Use bits 30-31 of port_flags to encode available port numbers. + * Current maxium is 4. + */ +#define SIL24_NPORTS2FLAG(nports) ((((unsigned)(nports) - 1) & 0x3) << 30) +#define SIL24_FLAG2NPORTS(flag) ((((flag) >> 30) & 0x3) + 1) + +static struct ata_port_info sil24_port_info[] = { + /* sil_3124 */ + { + .sht = &sil24_sht, + .flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4) | + SIL24_FLAG_PCIX_IRQ_WOC, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil24_ops, + }, + /* sil_3132 */ + { + .sht = &sil24_sht, + .flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(2), + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil24_ops, + }, + /* sil_3131/sil_3531 */ + { + .sht = &sil24_sht, + .flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(1), + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil24_ops, + }, +}; + +static int sil24_tag(int tag) +{ + if (unlikely(ata_tag_internal(tag))) + return 0; + return tag; +} + +static void sil24_dev_config(struct ata_port *ap, struct ata_device *dev) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + + if (dev->cdb_len == 16) + writel(PORT_CS_CDB16, port + PORT_CTRL_STAT); + else + writel(PORT_CS_CDB16, port + PORT_CTRL_CLR); +} + +static inline void sil24_update_tf(struct ata_port *ap) +{ + struct sil24_port_priv *pp = ap->private_data; + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + struct sil24_prb __iomem *prb = port; + u8 fis[6 * 4]; + + memcpy_fromio(fis, prb->fis, 6 * 4); + ata_tf_from_fis(fis, &pp->tf); +} + +static u8 sil24_check_status(struct ata_port *ap) +{ + struct sil24_port_priv *pp = ap->private_data; + return pp->tf.command; +} + +static int sil24_scr_map[] = { + [SCR_CONTROL] = 0, + [SCR_STATUS] = 1, + [SCR_ERROR] = 2, + [SCR_ACTIVE] = 3, +}; + +static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg) +{ + void __iomem *scr_addr = (void __iomem *)ap->ioaddr.scr_addr; + if (sc_reg < ARRAY_SIZE(sil24_scr_map)) { + void __iomem *addr; + addr = scr_addr + sil24_scr_map[sc_reg] * 4; + return readl(scr_addr + sil24_scr_map[sc_reg] * 4); + } + return 0xffffffffU; +} + +static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val) +{ + void __iomem *scr_addr = (void __iomem *)ap->ioaddr.scr_addr; + if (sc_reg < ARRAY_SIZE(sil24_scr_map)) { + void __iomem *addr; + addr = scr_addr + sil24_scr_map[sc_reg] * 4; + writel(val, scr_addr + sil24_scr_map[sc_reg] * 4); + } +} + +static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf) +{ + struct sil24_port_priv *pp = ap->private_data; + *tf = pp->tf; +} + +static int sil24_init_port(struct ata_port *ap) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + u32 tmp; + + writel(PORT_CS_INIT, port + PORT_CTRL_STAT); + ata_wait_register(port + PORT_CTRL_STAT, + PORT_CS_INIT, PORT_CS_INIT, 10, 100); + tmp = ata_wait_register(port + PORT_CTRL_STAT, + PORT_CS_RDY, 0, 10, 100); + + if ((tmp & (PORT_CS_INIT | PORT_CS_RDY)) != PORT_CS_RDY) + return -EIO; + return 0; +} + +static int sil24_softreset(struct ata_port *ap, unsigned int *class) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + struct sil24_port_priv *pp = ap->private_data; + struct sil24_prb *prb = &pp->cmd_block[0].ata.prb; + dma_addr_t paddr = pp->cmd_block_dma; + u32 mask, irq_stat; + const char *reason; + + DPRINTK("ENTER\n"); + + if (ata_port_offline(ap)) { + DPRINTK("PHY reports no device\n"); + *class = ATA_DEV_NONE; + goto out; + } + + /* put the port into known state */ + if (sil24_init_port(ap)) { + reason ="port not ready"; + goto err; + } + + /* do SRST */ + prb->ctrl = cpu_to_le16(PRB_CTRL_SRST); + prb->fis[1] = 0; /* no PM yet */ + + writel((u32)paddr, port + PORT_CMD_ACTIVATE); + writel((u64)paddr >> 32, port + PORT_CMD_ACTIVATE + 4); + + mask = (PORT_IRQ_COMPLETE | PORT_IRQ_ERROR) << PORT_IRQ_RAW_SHIFT; + irq_stat = ata_wait_register(port + PORT_IRQ_STAT, mask, 0x0, + 100, ATA_TMOUT_BOOT / HZ * 1000); + + writel(irq_stat, port + PORT_IRQ_STAT); /* clear IRQs */ + irq_stat >>= PORT_IRQ_RAW_SHIFT; + + if (!(irq_stat & PORT_IRQ_COMPLETE)) { + if (irq_stat & PORT_IRQ_ERROR) + reason = "SRST command error"; + else + reason = "timeout"; + goto err; + } + + sil24_update_tf(ap); + *class = ata_dev_classify(&pp->tf); + + if (*class == ATA_DEV_UNKNOWN) + *class = ATA_DEV_NONE; + + out: + DPRINTK("EXIT, class=%u\n", *class); + return 0; + + err: + ata_port_printk(ap, KERN_ERR, "softreset failed (%s)\n", reason); + return -EIO; +} + +static int sil24_hardreset(struct ata_port *ap, unsigned int *class) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + const char *reason; + int tout_msec, rc; + u32 tmp; + + /* sil24 does the right thing(tm) without any protection */ + sata_set_spd(ap); + + tout_msec = 100; + if (ata_port_online(ap)) + tout_msec = 5000; + + writel(PORT_CS_DEV_RST, port + PORT_CTRL_STAT); + tmp = ata_wait_register(port + PORT_CTRL_STAT, + PORT_CS_DEV_RST, PORT_CS_DEV_RST, 10, tout_msec); + + /* SStatus oscillates between zero and valid status after + * DEV_RST, debounce it. + */ + rc = sata_phy_debounce(ap, sata_deb_timing_long); + if (rc) { + reason = "PHY debouncing failed"; + goto err; + } + + if (tmp & PORT_CS_DEV_RST) { + if (ata_port_offline(ap)) + return 0; + reason = "link not ready"; + goto err; + } + + /* Sil24 doesn't store signature FIS after hardreset, so we + * can't wait for BSY to clear. Some devices take a long time + * to get ready and those devices will choke if we don't wait + * for BSY clearance here. Tell libata to perform follow-up + * softreset. + */ + return -EAGAIN; + + err: + ata_port_printk(ap, KERN_ERR, "hardreset failed (%s)\n", reason); + return -EIO; +} + +static inline void sil24_fill_sg(struct ata_queued_cmd *qc, + struct sil24_sge *sge) +{ + struct scatterlist *sg; + unsigned int idx = 0; + + ata_for_each_sg(sg, qc) { + sge->addr = cpu_to_le64(sg_dma_address(sg)); + sge->cnt = cpu_to_le32(sg_dma_len(sg)); + if (ata_sg_is_last(sg, qc)) + sge->flags = cpu_to_le32(SGE_TRM); + else + sge->flags = 0; + + sge++; + idx++; + } +} + +static void sil24_qc_prep(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct sil24_port_priv *pp = ap->private_data; + union sil24_cmd_block *cb; + struct sil24_prb *prb; + struct sil24_sge *sge; + u16 ctrl = 0; + + cb = &pp->cmd_block[sil24_tag(qc->tag)]; + + switch (qc->tf.protocol) { + case ATA_PROT_PIO: + case ATA_PROT_DMA: + case ATA_PROT_NCQ: + case ATA_PROT_NODATA: + prb = &cb->ata.prb; + sge = cb->ata.sge; + break; + + case ATA_PROT_ATAPI: + case ATA_PROT_ATAPI_DMA: + case ATA_PROT_ATAPI_NODATA: + prb = &cb->atapi.prb; + sge = cb->atapi.sge; + memset(cb->atapi.cdb, 0, 32); + memcpy(cb->atapi.cdb, qc->cdb, qc->dev->cdb_len); + + if (qc->tf.protocol != ATA_PROT_ATAPI_NODATA) { + if (qc->tf.flags & ATA_TFLAG_WRITE) + ctrl = PRB_CTRL_PACKET_WRITE; + else + ctrl = PRB_CTRL_PACKET_READ; + } + break; + + default: + prb = NULL; /* shut up, gcc */ + sge = NULL; + BUG(); + } + + prb->ctrl = cpu_to_le16(ctrl); + ata_tf_to_fis(&qc->tf, prb->fis, 0); + + if (qc->flags & ATA_QCFLAG_DMAMAP) + sil24_fill_sg(qc, sge); +} + +static unsigned int sil24_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct sil24_port_priv *pp = ap->private_data; + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + unsigned int tag = sil24_tag(qc->tag); + dma_addr_t paddr; + void __iomem *activate; + + paddr = pp->cmd_block_dma + tag * sizeof(*pp->cmd_block); + activate = port + PORT_CMD_ACTIVATE + tag * 8; + + writel((u32)paddr, activate); + writel((u64)paddr >> 32, activate + 4); + + return 0; +} + +static void sil24_irq_clear(struct ata_port *ap) +{ + /* unused */ +} + +static void sil24_freeze(struct ata_port *ap) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + + /* Port-wide IRQ mask in HOST_CTRL doesn't really work, clear + * PORT_IRQ_ENABLE instead. + */ + writel(0xffff, port + PORT_IRQ_ENABLE_CLR); +} + +static void sil24_thaw(struct ata_port *ap) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + u32 tmp; + + /* clear IRQ */ + tmp = readl(port + PORT_IRQ_STAT); + writel(tmp, port + PORT_IRQ_STAT); + + /* turn IRQ back on */ + writel(DEF_PORT_IRQ, port + PORT_IRQ_ENABLE_SET); +} + +static void sil24_error_intr(struct ata_port *ap) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + struct ata_eh_info *ehi = &ap->eh_info; + int freeze = 0; + u32 irq_stat; + + /* on error, we need to clear IRQ explicitly */ + irq_stat = readl(port + PORT_IRQ_STAT); + writel(irq_stat, port + PORT_IRQ_STAT); + + /* first, analyze and record host port events */ + ata_ehi_clear_desc(ehi); + + ata_ehi_push_desc(ehi, "irq_stat 0x%08x", irq_stat); + + if (irq_stat & (PORT_IRQ_PHYRDY_CHG | PORT_IRQ_DEV_XCHG)) { + ata_ehi_hotplugged(ehi); + ata_ehi_push_desc(ehi, ", %s", + irq_stat & PORT_IRQ_PHYRDY_CHG ? + "PHY RDY changed" : "device exchanged"); + freeze = 1; + } + + if (irq_stat & PORT_IRQ_UNK_FIS) { + ehi->err_mask |= AC_ERR_HSM; + ehi->action |= ATA_EH_SOFTRESET; + ata_ehi_push_desc(ehi , ", unknown FIS"); + freeze = 1; + } + + /* deal with command error */ + if (irq_stat & PORT_IRQ_ERROR) { + struct sil24_cerr_info *ci = NULL; + unsigned int err_mask = 0, action = 0; + struct ata_queued_cmd *qc; + u32 cerr; + + /* analyze CMD_ERR */ + cerr = readl(port + PORT_CMD_ERR); + if (cerr < ARRAY_SIZE(sil24_cerr_db)) + ci = &sil24_cerr_db[cerr]; + + if (ci && ci->desc) { + err_mask |= ci->err_mask; + action |= ci->action; + ata_ehi_push_desc(ehi, ", %s", ci->desc); + } else { + err_mask |= AC_ERR_OTHER; + action |= ATA_EH_SOFTRESET; + ata_ehi_push_desc(ehi, ", unknown command error %d", + cerr); + } + + /* record error info */ + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc) { + sil24_update_tf(ap); + qc->err_mask |= err_mask; + } else + ehi->err_mask |= err_mask; + + ehi->action |= action; + } + + /* freeze or abort */ + if (freeze) + ata_port_freeze(ap); + else + ata_port_abort(ap); +} + +static void sil24_finish_qc(struct ata_queued_cmd *qc) +{ + if (qc->flags & ATA_QCFLAG_RESULT_TF) + sil24_update_tf(qc->ap); +} + +static inline void sil24_host_intr(struct ata_port *ap) +{ + void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; + u32 slot_stat, qc_active; + int rc; + + slot_stat = readl(port + PORT_SLOT_STAT); + + if (unlikely(slot_stat & HOST_SSTAT_ATTN)) { + sil24_error_intr(ap); + return; + } + + if (ap->flags & SIL24_FLAG_PCIX_IRQ_WOC) + writel(PORT_IRQ_COMPLETE, port + PORT_IRQ_STAT); + + qc_active = slot_stat & ~HOST_SSTAT_ATTN; + rc = ata_qc_complete_multiple(ap, qc_active, sil24_finish_qc); + if (rc > 0) + return; + if (rc < 0) { + struct ata_eh_info *ehi = &ap->eh_info; + ehi->err_mask |= AC_ERR_HSM; + ehi->action |= ATA_EH_SOFTRESET; + ata_port_freeze(ap); + return; + } + + if (ata_ratelimit()) + ata_port_printk(ap, KERN_INFO, "spurious interrupt " + "(slot_stat 0x%x active_tag %d sactive 0x%x)\n", + slot_stat, ap->active_tag, ap->sactive); +} + +static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + struct sil24_host_priv *hpriv = host->private_data; + unsigned handled = 0; + u32 status; + int i; + + status = readl(hpriv->host_base + HOST_IRQ_STAT); + + if (status == 0xffffffff) { + printk(KERN_ERR DRV_NAME ": IRQ status == 0xffffffff, " + "PCI fault or device removal?\n"); + goto out; + } + + if (!(status & IRQ_STAT_4PORTS)) + goto out; + + spin_lock(&host->lock); + + for (i = 0; i < host->n_ports; i++) + if (status & (1 << i)) { + struct ata_port *ap = host->ports[i]; + if (ap && !(ap->flags & ATA_FLAG_DISABLED)) { + sil24_host_intr(host->ports[i]); + handled++; + } else + printk(KERN_ERR DRV_NAME + ": interrupt from disabled port %d\n", i); + } + + spin_unlock(&host->lock); + out: + return IRQ_RETVAL(handled); +} + +static void sil24_error_handler(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + + if (sil24_init_port(ap)) { + ata_eh_freeze_port(ap); + ehc->i.action |= ATA_EH_HARDRESET; + } + + /* perform recovery */ + ata_do_eh(ap, ata_std_prereset, sil24_softreset, sil24_hardreset, + ata_std_postreset); +} + +static void sil24_post_internal_cmd(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + if (qc->flags & ATA_QCFLAG_FAILED) + qc->err_mask |= AC_ERR_OTHER; + + /* make DMA engine forget about the failed command */ + if (qc->err_mask) + sil24_init_port(ap); +} + +static inline void sil24_cblk_free(struct sil24_port_priv *pp, struct device *dev) +{ + const size_t cb_size = sizeof(*pp->cmd_block) * SIL24_MAX_CMDS; + + dma_free_coherent(dev, cb_size, pp->cmd_block, pp->cmd_block_dma); +} + +static int sil24_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct sil24_port_priv *pp; + union sil24_cmd_block *cb; + size_t cb_size = sizeof(*cb) * SIL24_MAX_CMDS; + dma_addr_t cb_dma; + int rc = -ENOMEM; + + pp = kzalloc(sizeof(*pp), GFP_KERNEL); + if (!pp) + goto err_out; + + pp->tf.command = ATA_DRDY; + + cb = dma_alloc_coherent(dev, cb_size, &cb_dma, GFP_KERNEL); + if (!cb) + goto err_out_pp; + memset(cb, 0, cb_size); + + rc = ata_pad_alloc(ap, dev); + if (rc) + goto err_out_pad; + + pp->cmd_block = cb; + pp->cmd_block_dma = cb_dma; + + ap->private_data = pp; + + return 0; + +err_out_pad: + sil24_cblk_free(pp, dev); +err_out_pp: + kfree(pp); +err_out: + return rc; +} + +static void sil24_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct sil24_port_priv *pp = ap->private_data; + + sil24_cblk_free(pp, dev); + ata_pad_free(ap, dev); + kfree(pp); +} + +static void sil24_host_stop(struct ata_host *host) +{ + struct sil24_host_priv *hpriv = host->private_data; + struct pci_dev *pdev = to_pci_dev(host->dev); + + pci_iounmap(pdev, hpriv->host_base); + pci_iounmap(pdev, hpriv->port_base); + kfree(hpriv); +} + +static void sil24_init_controller(struct pci_dev *pdev, int n_ports, + unsigned long port_flags, + void __iomem *host_base, + void __iomem *port_base) +{ + u32 tmp; + int i; + + /* GPIO off */ + writel(0, host_base + HOST_FLASH_CMD); + + /* clear global reset & mask interrupts during initialization */ + writel(0, host_base + HOST_CTRL); + + /* init ports */ + for (i = 0; i < n_ports; i++) { + void __iomem *port = port_base + i * PORT_REGS_SIZE; + + /* Initial PHY setting */ + writel(0x20c, port + PORT_PHY_CFG); + + /* Clear port RST */ + tmp = readl(port + PORT_CTRL_STAT); + if (tmp & PORT_CS_PORT_RST) { + writel(PORT_CS_PORT_RST, port + PORT_CTRL_CLR); + tmp = ata_wait_register(port + PORT_CTRL_STAT, + PORT_CS_PORT_RST, + PORT_CS_PORT_RST, 10, 100); + if (tmp & PORT_CS_PORT_RST) + dev_printk(KERN_ERR, &pdev->dev, + "failed to clear port RST\n"); + } + + /* Configure IRQ WoC */ + if (port_flags & SIL24_FLAG_PCIX_IRQ_WOC) + writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_STAT); + else + writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR); + + /* Zero error counters. */ + writel(0x8000, port + PORT_DECODE_ERR_THRESH); + writel(0x8000, port + PORT_CRC_ERR_THRESH); + writel(0x8000, port + PORT_HSHK_ERR_THRESH); + writel(0x0000, port + PORT_DECODE_ERR_CNT); + writel(0x0000, port + PORT_CRC_ERR_CNT); + writel(0x0000, port + PORT_HSHK_ERR_CNT); + + /* Always use 64bit activation */ + writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_CLR); + + /* Clear port multiplier enable and resume bits */ + writel(PORT_CS_PM_EN | PORT_CS_RESUME, port + PORT_CTRL_CLR); + } + + /* Turn on interrupts */ + writel(IRQ_STAT_4PORTS, host_base + HOST_CTRL); +} + +static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version = 0; + unsigned int board_id = (unsigned int)ent->driver_data; + struct ata_port_info *pinfo = &sil24_port_info[board_id]; + struct ata_probe_ent *probe_ent = NULL; + struct sil24_host_priv *hpriv = NULL; + void __iomem *host_base = NULL; + void __iomem *port_base = NULL; + int i, rc; + u32 tmp; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto out_disable; + + rc = -ENOMEM; + /* map mmio registers */ + host_base = pci_iomap(pdev, 0, 0); + if (!host_base) + goto out_free; + port_base = pci_iomap(pdev, 2, 0); + if (!port_base) + goto out_free; + + /* allocate & init probe_ent and hpriv */ + probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL); + if (!probe_ent) + goto out_free; + + hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL); + if (!hpriv) + goto out_free; + + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + probe_ent->sht = pinfo->sht; + probe_ent->port_flags = pinfo->flags; + probe_ent->pio_mask = pinfo->pio_mask; + probe_ent->mwdma_mask = pinfo->mwdma_mask; + probe_ent->udma_mask = pinfo->udma_mask; + probe_ent->port_ops = pinfo->port_ops; + probe_ent->n_ports = SIL24_FLAG2NPORTS(pinfo->flags); + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->private_data = hpriv; + + hpriv->host_base = host_base; + hpriv->port_base = port_base; + + /* + * Configure the device + */ + if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) { + rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK); + if (rc) { + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "64-bit DMA enable failed\n"); + goto out_free; + } + } + } else { + rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit DMA enable failed\n"); + goto out_free; + } + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit consistent DMA enable failed\n"); + goto out_free; + } + } + + /* Apply workaround for completion IRQ loss on PCI-X errata */ + if (probe_ent->port_flags & SIL24_FLAG_PCIX_IRQ_WOC) { + tmp = readl(host_base + HOST_CTRL); + if (tmp & (HOST_CTRL_TRDY | HOST_CTRL_STOP | HOST_CTRL_DEVSEL)) + dev_printk(KERN_INFO, &pdev->dev, + "Applying completion IRQ loss on PCI-X " + "errata fix\n"); + else + probe_ent->port_flags &= ~SIL24_FLAG_PCIX_IRQ_WOC; + } + + for (i = 0; i < probe_ent->n_ports; i++) { + unsigned long portu = + (unsigned long)port_base + i * PORT_REGS_SIZE; + + probe_ent->port[i].cmd_addr = portu; + probe_ent->port[i].scr_addr = portu + PORT_SCONTROL; + + ata_std_ports(&probe_ent->port[i]); + } + + sil24_init_controller(pdev, probe_ent->n_ports, probe_ent->port_flags, + host_base, port_base); + + pci_set_master(pdev); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + + kfree(probe_ent); + return 0; + + out_free: + if (host_base) + pci_iounmap(pdev, host_base); + if (port_base) + pci_iounmap(pdev, port_base); + kfree(probe_ent); + kfree(hpriv); + pci_release_regions(pdev); + out_disable: + pci_disable_device(pdev); + return rc; +} + +#ifdef CONFIG_PM +static int sil24_pci_device_resume(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + struct sil24_host_priv *hpriv = host->private_data; + + ata_pci_device_do_resume(pdev); + + if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) + writel(HOST_CTRL_GLOBAL_RST, hpriv->host_base + HOST_CTRL); + + sil24_init_controller(pdev, host->n_ports, host->ports[0]->flags, + hpriv->host_base, hpriv->port_base); + + ata_host_resume(host); + + return 0; +} +#endif + +static int __init sil24_init(void) +{ + return pci_register_driver(&sil24_pci_driver); +} + +static void __exit sil24_exit(void) +{ + pci_unregister_driver(&sil24_pci_driver); +} + +MODULE_AUTHOR("Tejun Heo"); +MODULE_DESCRIPTION("Silicon Image 3124/3132 SATA low-level driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sil24_pci_tbl); + +module_init(sil24_init); +module_exit(sil24_exit); diff --git a/drivers/ata/sata_sis.c b/drivers/ata/sata_sis.c new file mode 100644 index 00000000000..18d49fff8dc --- /dev/null +++ b/drivers/ata/sata_sis.c @@ -0,0 +1,347 @@ +/* + * sata_sis.c - Silicon Integrated Systems SATA + * + * Maintained by: Uwe Koziolek + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2004 Uwe Koziolek + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available under NDA. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "sata_sis" +#define DRV_VERSION "0.6" + +enum { + sis_180 = 0, + SIS_SCR_PCI_BAR = 5, + + /* PCI configuration registers */ + SIS_GENCTL = 0x54, /* IDE General Control register */ + SIS_SCR_BASE = 0xc0, /* sata0 phy SCR registers */ + SIS180_SATA1_OFS = 0x10, /* offset from sata0->sata1 phy regs */ + SIS182_SATA1_OFS = 0x20, /* offset from sata0->sata1 phy regs */ + SIS_PMR = 0x90, /* port mapping register */ + SIS_PMR_COMBINED = 0x30, + + /* random bits */ + SIS_FLAG_CFGSCR = (1 << 30), /* host flag: SCRs via PCI cfg */ + + GENCTL_IOMAPPED_SCR = (1 << 26), /* if set, SCRs are in IO space */ +}; + +static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); + +static const struct pci_device_id sis_pci_tbl[] = { + { PCI_VENDOR_ID_SI, 0x180, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sis_180 }, + { PCI_VENDOR_ID_SI, 0x181, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sis_180 }, + { PCI_VENDOR_ID_SI, 0x182, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sis_180 }, + { } /* terminate list */ +}; + + +static struct pci_driver sis_pci_driver = { + .name = DRV_NAME, + .id_table = sis_pci_tbl, + .probe = sis_init_one, + .remove = ata_pci_remove_one, +}; + +static struct scsi_host_template sis_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = ATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations sis_ops = { + .port_disable = ata_port_disable, + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + .scr_read = sis_scr_read, + .scr_write = sis_scr_write, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static struct ata_port_info sis_port_info = { + .sht = &sis_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY, + .pio_mask = 0x1f, + .mwdma_mask = 0x7, + .udma_mask = 0x7f, + .port_ops = &sis_ops, +}; + + +MODULE_AUTHOR("Uwe Koziolek"); +MODULE_DESCRIPTION("low-level driver for Silicon Integratad Systems SATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sis_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg, int device) +{ + unsigned int addr = SIS_SCR_BASE + (4 * sc_reg); + + if (port_no) { + if (device == 0x182) + addr += SIS182_SATA1_OFS; + else + addr += SIS180_SATA1_OFS; + } + + return addr; +} + +static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg, pdev->device); + u32 val, val2 = 0; + u8 pmr; + + if (sc_reg == SCR_ERROR) /* doesn't exist in PCI cfg space */ + return 0xffffffff; + + pci_read_config_byte(pdev, SIS_PMR, &pmr); + + pci_read_config_dword(pdev, cfg_addr, &val); + + if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED)) + pci_read_config_dword(pdev, cfg_addr+0x10, &val2); + + return val|val2; +} + +static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr, pdev->device); + u8 pmr; + + if (scr == SCR_ERROR) /* doesn't exist in PCI cfg space */ + return; + + pci_read_config_byte(pdev, SIS_PMR, &pmr); + + pci_write_config_dword(pdev, cfg_addr, val); + + if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED)) + pci_write_config_dword(pdev, cfg_addr+0x10, val); +} + +static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 val, val2 = 0; + u8 pmr; + + if (sc_reg > SCR_CONTROL) + return 0xffffffffU; + + if (ap->flags & SIS_FLAG_CFGSCR) + return sis_scr_cfg_read(ap, sc_reg); + + pci_read_config_byte(pdev, SIS_PMR, &pmr); + + val = inl(ap->ioaddr.scr_addr + (sc_reg * 4)); + + if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED)) + val2 = inl(ap->ioaddr.scr_addr + (sc_reg * 4) + 0x10); + + return val | val2; +} + +static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 pmr; + + if (sc_reg > SCR_CONTROL) + return; + + pci_read_config_byte(pdev, SIS_PMR, &pmr); + + if (ap->flags & SIS_FLAG_CFGSCR) + sis_scr_cfg_write(ap, sc_reg, val); + else { + outl(val, ap->ioaddr.scr_addr + (sc_reg * 4)); + if ((pdev->device == 0x182) || (pmr & SIS_PMR_COMBINED)) + outl(val, ap->ioaddr.scr_addr + (sc_reg * 4)+0x10); + } +} + +static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + int rc; + u32 genctl; + struct ata_port_info *ppi[2]; + int pci_dev_busy = 0; + u8 pmr; + u8 port2_start; + + if (!printed_version++) + dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + ppi[0] = ppi[1] = &sis_port_info; + probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY); + if (!probe_ent) { + rc = -ENOMEM; + goto err_out_regions; + } + + /* check and see if the SCRs are in IO space or PCI cfg space */ + pci_read_config_dword(pdev, SIS_GENCTL, &genctl); + if ((genctl & GENCTL_IOMAPPED_SCR) == 0) + probe_ent->port_flags |= SIS_FLAG_CFGSCR; + + /* if hardware thinks SCRs are in IO space, but there are + * no IO resources assigned, change to PCI cfg space. + */ + if ((!(probe_ent->port_flags & SIS_FLAG_CFGSCR)) && + ((pci_resource_start(pdev, SIS_SCR_PCI_BAR) == 0) || + (pci_resource_len(pdev, SIS_SCR_PCI_BAR) < 128))) { + genctl &= ~GENCTL_IOMAPPED_SCR; + pci_write_config_dword(pdev, SIS_GENCTL, genctl); + probe_ent->port_flags |= SIS_FLAG_CFGSCR; + } + + pci_read_config_byte(pdev, SIS_PMR, &pmr); + if (ent->device != 0x182) { + if ((pmr & SIS_PMR_COMBINED) == 0) { + dev_printk(KERN_INFO, &pdev->dev, + "Detected SiS 180/181 chipset in SATA mode\n"); + port2_start = 64; + } + else { + dev_printk(KERN_INFO, &pdev->dev, + "Detected SiS 180/181 chipset in combined mode\n"); + port2_start=0; + } + } + else { + dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182 chipset\n"); + port2_start = 0x20; + } + + if (!(probe_ent->port_flags & SIS_FLAG_CFGSCR)) { + probe_ent->port[0].scr_addr = + pci_resource_start(pdev, SIS_SCR_PCI_BAR); + probe_ent->port[1].scr_addr = + pci_resource_start(pdev, SIS_SCR_PCI_BAR) + port2_start; + } + + pci_set_master(pdev); + pci_intx(pdev, 1); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_regions: + pci_release_regions(pdev); + +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; + +} + +static int __init sis_init(void) +{ + return pci_register_driver(&sis_pci_driver); +} + +static void __exit sis_exit(void) +{ + pci_unregister_driver(&sis_pci_driver); +} + +module_init(sis_init); +module_exit(sis_exit); + diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c new file mode 100644 index 00000000000..d6d6658d832 --- /dev/null +++ b/drivers/ata/sata_svw.c @@ -0,0 +1,508 @@ +/* + * sata_svw.c - ServerWorks / Apple K2 SATA + * + * Maintained by: Benjamin Herrenschmidt <benh@kernel.crashing.org> and + * Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2003 Benjamin Herrenschmidt <benh@kernel.crashing.org> + * + * Bits from Jeff Garzik, Copyright RedHat, Inc. + * + * This driver probably works with non-Apple versions of the + * Broadcom chipset... + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available under NDA. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#ifdef CONFIG_PPC_OF +#include <asm/prom.h> +#include <asm/pci-bridge.h> +#endif /* CONFIG_PPC_OF */ + +#define DRV_NAME "sata_svw" +#define DRV_VERSION "2.0" + +enum { + /* Taskfile registers offsets */ + K2_SATA_TF_CMD_OFFSET = 0x00, + K2_SATA_TF_DATA_OFFSET = 0x00, + K2_SATA_TF_ERROR_OFFSET = 0x04, + K2_SATA_TF_NSECT_OFFSET = 0x08, + K2_SATA_TF_LBAL_OFFSET = 0x0c, + K2_SATA_TF_LBAM_OFFSET = 0x10, + K2_SATA_TF_LBAH_OFFSET = 0x14, + K2_SATA_TF_DEVICE_OFFSET = 0x18, + K2_SATA_TF_CMDSTAT_OFFSET = 0x1c, + K2_SATA_TF_CTL_OFFSET = 0x20, + + /* DMA base */ + K2_SATA_DMA_CMD_OFFSET = 0x30, + + /* SCRs base */ + K2_SATA_SCR_STATUS_OFFSET = 0x40, + K2_SATA_SCR_ERROR_OFFSET = 0x44, + K2_SATA_SCR_CONTROL_OFFSET = 0x48, + + /* Others */ + K2_SATA_SICR1_OFFSET = 0x80, + K2_SATA_SICR2_OFFSET = 0x84, + K2_SATA_SIM_OFFSET = 0x88, + + /* Port stride */ + K2_SATA_PORT_OFFSET = 0x100, +}; + +static u8 k2_stat_check_status(struct ata_port *ap); + + +static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + if (sc_reg > SCR_CONTROL) + return 0xffffffffU; + return readl((void *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + + +static void k2_sata_scr_write (struct ata_port *ap, unsigned int sc_reg, + u32 val) +{ + if (sc_reg > SCR_CONTROL) + return; + writel(val, (void *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + + +static void k2_sata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; + + if (tf->ctl != ap->last_ctl) { + writeb(tf->ctl, ioaddr->ctl_addr); + ap->last_ctl = tf->ctl; + ata_wait_idle(ap); + } + if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { + writew(tf->feature | (((u16)tf->hob_feature) << 8), ioaddr->feature_addr); + writew(tf->nsect | (((u16)tf->hob_nsect) << 8), ioaddr->nsect_addr); + writew(tf->lbal | (((u16)tf->hob_lbal) << 8), ioaddr->lbal_addr); + writew(tf->lbam | (((u16)tf->hob_lbam) << 8), ioaddr->lbam_addr); + writew(tf->lbah | (((u16)tf->hob_lbah) << 8), ioaddr->lbah_addr); + } else if (is_addr) { + writew(tf->feature, ioaddr->feature_addr); + writew(tf->nsect, ioaddr->nsect_addr); + writew(tf->lbal, ioaddr->lbal_addr); + writew(tf->lbam, ioaddr->lbam_addr); + writew(tf->lbah, ioaddr->lbah_addr); + } + + if (tf->flags & ATA_TFLAG_DEVICE) + writeb(tf->device, ioaddr->device_addr); + + ata_wait_idle(ap); +} + + +static void k2_sata_tf_read(struct ata_port *ap, struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + u16 nsect, lbal, lbam, lbah, feature; + + tf->command = k2_stat_check_status(ap); + tf->device = readw(ioaddr->device_addr); + feature = readw(ioaddr->error_addr); + nsect = readw(ioaddr->nsect_addr); + lbal = readw(ioaddr->lbal_addr); + lbam = readw(ioaddr->lbam_addr); + lbah = readw(ioaddr->lbah_addr); + + tf->feature = feature; + tf->nsect = nsect; + tf->lbal = lbal; + tf->lbam = lbam; + tf->lbah = lbah; + + if (tf->flags & ATA_TFLAG_LBA48) { + tf->hob_feature = feature >> 8; + tf->hob_nsect = nsect >> 8; + tf->hob_lbal = lbal >> 8; + tf->hob_lbam = lbam >> 8; + tf->hob_lbah = lbah >> 8; + } +} + +/** + * k2_bmdma_setup_mmio - Set up PCI IDE BMDMA transaction (MMIO) + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void k2_bmdma_setup_mmio (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u8 dmactl; + void *mmio = (void *) ap->ioaddr.bmdma_addr; + /* load PRD table addr. */ + mb(); /* make sure PRD table writes are visible to controller */ + writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS); + + /* specify data direction, triple-check start bit is clear */ + dmactl = readb(mmio + ATA_DMA_CMD); + dmactl &= ~(ATA_DMA_WR | ATA_DMA_START); + if (!rw) + dmactl |= ATA_DMA_WR; + writeb(dmactl, mmio + ATA_DMA_CMD); + + /* issue r/w command if this is not a ATA DMA command*/ + if (qc->tf.protocol != ATA_PROT_DMA) + ap->ops->exec_command(ap, &qc->tf); +} + +/** + * k2_bmdma_start_mmio - Start a PCI IDE BMDMA transaction (MMIO) + * @qc: Info associated with this ATA transaction. + * + * LOCKING: + * spin_lock_irqsave(host lock) + */ + +static void k2_bmdma_start_mmio (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void *mmio = (void *) ap->ioaddr.bmdma_addr; + u8 dmactl; + + /* start host DMA transaction */ + dmactl = readb(mmio + ATA_DMA_CMD); + writeb(dmactl | ATA_DMA_START, mmio + ATA_DMA_CMD); + /* There is a race condition in certain SATA controllers that can + be seen when the r/w command is given to the controller before the + host DMA is started. On a Read command, the controller would initiate + the command to the drive even before it sees the DMA start. When there + are very fast drives connected to the controller, or when the data request + hits in the drive cache, there is the possibility that the drive returns a part + or all of the requested data to the controller before the DMA start is issued. + In this case, the controller would become confused as to what to do with the data. + In the worst case when all the data is returned back to the controller, the + controller could hang. In other cases it could return partial data returning + in data corruption. This problem has been seen in PPC systems and can also appear + on an system with very fast disks, where the SATA controller is sitting behind a + number of bridges, and hence there is significant latency between the r/w command + and the start command. */ + /* issue r/w command if the access is to ATA*/ + if (qc->tf.protocol == ATA_PROT_DMA) + ap->ops->exec_command(ap, &qc->tf); +} + + +static u8 k2_stat_check_status(struct ata_port *ap) +{ + return readl((void *) ap->ioaddr.status_addr); +} + +#ifdef CONFIG_PPC_OF +/* + * k2_sata_proc_info + * inout : decides on the direction of the dataflow and the meaning of the + * variables + * buffer: If inout==FALSE data is being written to it else read from it + * *start: If inout==FALSE start of the valid data in the buffer + * offset: If inout==FALSE offset from the beginning of the imaginary file + * from which we start writing into the buffer + * length: If inout==FALSE max number of bytes to be written into the buffer + * else number of bytes in the buffer + */ +static int k2_sata_proc_info(struct Scsi_Host *shost, char *page, char **start, + off_t offset, int count, int inout) +{ + struct ata_port *ap; + struct device_node *np; + int len, index; + + /* Find the ata_port */ + ap = ata_shost_to_port(shost); + if (ap == NULL) + return 0; + + /* Find the OF node for the PCI device proper */ + np = pci_device_to_OF_node(to_pci_dev(ap->host->dev)); + if (np == NULL) + return 0; + + /* Match it to a port node */ + index = (ap == ap->host->ports[0]) ? 0 : 1; + for (np = np->child; np != NULL; np = np->sibling) { + const u32 *reg = get_property(np, "reg", NULL); + if (!reg) + continue; + if (index == *reg) + break; + } + if (np == NULL) + return 0; + + len = sprintf(page, "devspec: %s\n", np->full_name); + + return len; +} +#endif /* CONFIG_PPC_OF */ + + +static struct scsi_host_template k2_sata_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, +#ifdef CONFIG_PPC_OF + .proc_info = k2_sata_proc_info, +#endif + .bios_param = ata_std_bios_param, +}; + + +static const struct ata_port_operations k2_sata_ops = { + .port_disable = ata_port_disable, + .tf_load = k2_sata_tf_load, + .tf_read = k2_sata_tf_read, + .check_status = k2_stat_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + .bmdma_setup = k2_bmdma_setup_mmio, + .bmdma_start = k2_bmdma_start_mmio, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + .scr_read = k2_sata_scr_read, + .scr_write = k2_sata_scr_write, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static void k2_sata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = base + K2_SATA_TF_CMD_OFFSET; + port->data_addr = base + K2_SATA_TF_DATA_OFFSET; + port->feature_addr = + port->error_addr = base + K2_SATA_TF_ERROR_OFFSET; + port->nsect_addr = base + K2_SATA_TF_NSECT_OFFSET; + port->lbal_addr = base + K2_SATA_TF_LBAL_OFFSET; + port->lbam_addr = base + K2_SATA_TF_LBAM_OFFSET; + port->lbah_addr = base + K2_SATA_TF_LBAH_OFFSET; + port->device_addr = base + K2_SATA_TF_DEVICE_OFFSET; + port->command_addr = + port->status_addr = base + K2_SATA_TF_CMDSTAT_OFFSET; + port->altstatus_addr = + port->ctl_addr = base + K2_SATA_TF_CTL_OFFSET; + port->bmdma_addr = base + K2_SATA_DMA_CMD_OFFSET; + port->scr_addr = base + K2_SATA_SCR_STATUS_OFFSET; +} + + +static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + unsigned long base; + void __iomem *mmio_base; + int pci_dev_busy = 0; + int rc; + int i; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + /* + * If this driver happens to only be useful on Apple's K2, then + * we should check that here as it has a normal Serverworks ID + */ + rc = pci_enable_device(pdev); + if (rc) + return rc; + /* + * Check if we have resources mapped at all (second function may + * have been disabled by firmware) + */ + if (pci_resource_len(pdev, 5) == 0) + return -ENODEV; + + /* Request PCI regions */ + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, 5, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + base = (unsigned long) mmio_base; + + /* Clear a magic bit in SCR1 according to Darwin, those help + * some funky seagate drives (though so far, those were already + * set by the firmware on the machines I had access to) + */ + writel(readl(mmio_base + K2_SATA_SICR1_OFFSET) & ~0x00040000, + mmio_base + K2_SATA_SICR1_OFFSET); + + /* Clear SATA error & interrupts we don't use */ + writel(0xffffffff, mmio_base + K2_SATA_SCR_ERROR_OFFSET); + writel(0x0, mmio_base + K2_SATA_SIM_OFFSET); + + probe_ent->sht = &k2_sata_sht; + probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO; + probe_ent->port_ops = &k2_sata_ops; + probe_ent->n_ports = 4; + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + + /* We don't care much about the PIO/UDMA masks, but the core won't like us + * if we don't fill these + */ + probe_ent->pio_mask = 0x1f; + probe_ent->mwdma_mask = 0x7; + probe_ent->udma_mask = 0x7f; + + /* different controllers have different number of ports - currently 4 or 8 */ + /* All ports are on the same function. Multi-function device is no + * longer available. This should not be seen in any system. */ + for (i = 0; i < ent->driver_data; i++) + k2_sata_setup_port(&probe_ent->port[i], base + i * K2_SATA_PORT_OFFSET); + + pci_set_master(pdev); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; +} + +/* 0x240 is device ID for Apple K2 device + * 0x241 is device ID for Serverworks Frodo4 + * 0x242 is device ID for Serverworks Frodo8 + * 0x24a is device ID for BCM5785 (aka HT1000) HT southbridge integrated SATA + * controller + * */ +static const struct pci_device_id k2_sata_pci_tbl[] = { + { 0x1166, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 }, + { 0x1166, 0x0241, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 }, + { 0x1166, 0x0242, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 }, + { 0x1166, 0x024a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 }, + { 0x1166, 0x024b, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 }, + { } +}; + + +static struct pci_driver k2_sata_pci_driver = { + .name = DRV_NAME, + .id_table = k2_sata_pci_tbl, + .probe = k2_sata_init_one, + .remove = ata_pci_remove_one, +}; + + +static int __init k2_sata_init(void) +{ + return pci_register_driver(&k2_sata_pci_driver); +} + + +static void __exit k2_sata_exit(void) +{ + pci_unregister_driver(&k2_sata_pci_driver); +} + + +MODULE_AUTHOR("Benjamin Herrenschmidt"); +MODULE_DESCRIPTION("low-level driver for K2 SATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, k2_sata_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_init(k2_sata_init); +module_exit(k2_sata_exit); diff --git a/drivers/ata/sata_sx4.c b/drivers/ata/sata_sx4.c new file mode 100644 index 00000000000..091867e10ea --- /dev/null +++ b/drivers/ata/sata_sx4.c @@ -0,0 +1,1502 @@ +/* + * sata_sx4.c - Promise SATA + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2003-2004 Red Hat, Inc. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available under NDA. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_cmnd.h> +#include <linux/libata.h> +#include <asm/io.h> +#include "sata_promise.h" + +#define DRV_NAME "sata_sx4" +#define DRV_VERSION "0.9" + + +enum { + PDC_PRD_TBL = 0x44, /* Direct command DMA table addr */ + + PDC_PKT_SUBMIT = 0x40, /* Command packet pointer addr */ + PDC_HDMA_PKT_SUBMIT = 0x100, /* Host DMA packet pointer addr */ + PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */ + PDC_HDMA_CTLSTAT = 0x12C, /* Host DMA control / status */ + + PDC_20621_SEQCTL = 0x400, + PDC_20621_SEQMASK = 0x480, + PDC_20621_GENERAL_CTL = 0x484, + PDC_20621_PAGE_SIZE = (32 * 1024), + + /* chosen, not constant, values; we design our own DIMM mem map */ + PDC_20621_DIMM_WINDOW = 0x0C, /* page# for 32K DIMM window */ + PDC_20621_DIMM_BASE = 0x00200000, + PDC_20621_DIMM_DATA = (64 * 1024), + PDC_DIMM_DATA_STEP = (256 * 1024), + PDC_DIMM_WINDOW_STEP = (8 * 1024), + PDC_DIMM_HOST_PRD = (6 * 1024), + PDC_DIMM_HOST_PKT = (128 * 0), + PDC_DIMM_HPKT_PRD = (128 * 1), + PDC_DIMM_ATA_PKT = (128 * 2), + PDC_DIMM_APKT_PRD = (128 * 3), + PDC_DIMM_HEADER_SZ = PDC_DIMM_APKT_PRD + 128, + PDC_PAGE_WINDOW = 0x40, + PDC_PAGE_DATA = PDC_PAGE_WINDOW + + (PDC_20621_DIMM_DATA / PDC_20621_PAGE_SIZE), + PDC_PAGE_SET = PDC_DIMM_DATA_STEP / PDC_20621_PAGE_SIZE, + + PDC_CHIP0_OFS = 0xC0000, /* offset of chip #0 */ + + PDC_20621_ERR_MASK = (1<<19) | (1<<20) | (1<<21) | (1<<22) | + (1<<23), + + board_20621 = 0, /* FastTrak S150 SX4 */ + + PDC_RESET = (1 << 11), /* HDMA reset */ + + PDC_MAX_HDMA = 32, + PDC_HDMA_Q_MASK = (PDC_MAX_HDMA - 1), + + PDC_DIMM0_SPD_DEV_ADDRESS = 0x50, + PDC_DIMM1_SPD_DEV_ADDRESS = 0x51, + PDC_MAX_DIMM_MODULE = 0x02, + PDC_I2C_CONTROL_OFFSET = 0x48, + PDC_I2C_ADDR_DATA_OFFSET = 0x4C, + PDC_DIMM0_CONTROL_OFFSET = 0x80, + PDC_DIMM1_CONTROL_OFFSET = 0x84, + PDC_SDRAM_CONTROL_OFFSET = 0x88, + PDC_I2C_WRITE = 0x00000000, + PDC_I2C_READ = 0x00000040, + PDC_I2C_START = 0x00000080, + PDC_I2C_MASK_INT = 0x00000020, + PDC_I2C_COMPLETE = 0x00010000, + PDC_I2C_NO_ACK = 0x00100000, + PDC_DIMM_SPD_SUBADDRESS_START = 0x00, + PDC_DIMM_SPD_SUBADDRESS_END = 0x7F, + PDC_DIMM_SPD_ROW_NUM = 3, + PDC_DIMM_SPD_COLUMN_NUM = 4, + PDC_DIMM_SPD_MODULE_ROW = 5, + PDC_DIMM_SPD_TYPE = 11, + PDC_DIMM_SPD_FRESH_RATE = 12, + PDC_DIMM_SPD_BANK_NUM = 17, + PDC_DIMM_SPD_CAS_LATENCY = 18, + PDC_DIMM_SPD_ATTRIBUTE = 21, + PDC_DIMM_SPD_ROW_PRE_CHARGE = 27, + PDC_DIMM_SPD_ROW_ACTIVE_DELAY = 28, + PDC_DIMM_SPD_RAS_CAS_DELAY = 29, + PDC_DIMM_SPD_ACTIVE_PRECHARGE = 30, + PDC_DIMM_SPD_SYSTEM_FREQ = 126, + PDC_CTL_STATUS = 0x08, + PDC_DIMM_WINDOW_CTLR = 0x0C, + PDC_TIME_CONTROL = 0x3C, + PDC_TIME_PERIOD = 0x40, + PDC_TIME_COUNTER = 0x44, + PDC_GENERAL_CTLR = 0x484, + PCI_PLL_INIT = 0x8A531824, + PCI_X_TCOUNT = 0xEE1E5CFF +}; + + +struct pdc_port_priv { + u8 dimm_buf[(ATA_PRD_SZ * ATA_MAX_PRD) + 512]; + u8 *pkt; + dma_addr_t pkt_dma; +}; + +struct pdc_host_priv { + void __iomem *dimm_mmio; + + unsigned int doing_hdma; + unsigned int hdma_prod; + unsigned int hdma_cons; + struct { + struct ata_queued_cmd *qc; + unsigned int seq; + unsigned long pkt_ofs; + } hdma[32]; +}; + + +static int pdc_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_regs *regs); +static void pdc_eng_timeout(struct ata_port *ap); +static void pdc_20621_phy_reset (struct ata_port *ap); +static int pdc_port_start(struct ata_port *ap); +static void pdc_port_stop(struct ata_port *ap); +static void pdc20621_qc_prep(struct ata_queued_cmd *qc); +static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf); +static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf); +static void pdc20621_host_stop(struct ata_host *host); +static unsigned int pdc20621_dimm_init(struct ata_probe_ent *pe); +static int pdc20621_detect_dimm(struct ata_probe_ent *pe); +static unsigned int pdc20621_i2c_read(struct ata_probe_ent *pe, + u32 device, u32 subaddr, u32 *pdata); +static int pdc20621_prog_dimm0(struct ata_probe_ent *pe); +static unsigned int pdc20621_prog_dimm_global(struct ata_probe_ent *pe); +#ifdef ATA_VERBOSE_DEBUG +static void pdc20621_get_from_dimm(struct ata_probe_ent *pe, + void *psource, u32 offset, u32 size); +#endif +static void pdc20621_put_to_dimm(struct ata_probe_ent *pe, + void *psource, u32 offset, u32 size); +static void pdc20621_irq_clear(struct ata_port *ap); +static unsigned int pdc20621_qc_issue_prot(struct ata_queued_cmd *qc); + + +static struct scsi_host_template pdc_sata_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations pdc_20621_ops = { + .port_disable = ata_port_disable, + .tf_load = pdc_tf_load_mmio, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = pdc_exec_command_mmio, + .dev_select = ata_std_dev_select, + .phy_reset = pdc_20621_phy_reset, + .qc_prep = pdc20621_qc_prep, + .qc_issue = pdc20621_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + .eng_timeout = pdc_eng_timeout, + .irq_handler = pdc20621_interrupt, + .irq_clear = pdc20621_irq_clear, + .port_start = pdc_port_start, + .port_stop = pdc_port_stop, + .host_stop = pdc20621_host_stop, +}; + +static const struct ata_port_info pdc_port_info[] = { + /* board_20621 */ + { + .sht = &pdc_sata_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_SRST | ATA_FLAG_MMIO | + ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x7f, /* udma0-6 ; FIXME */ + .port_ops = &pdc_20621_ops, + }, + +}; + +static const struct pci_device_id pdc_sata_pci_tbl[] = { + { PCI_VENDOR_ID_PROMISE, 0x6622, PCI_ANY_ID, PCI_ANY_ID, 0, 0, + board_20621 }, + { } /* terminate list */ +}; + + +static struct pci_driver pdc_sata_pci_driver = { + .name = DRV_NAME, + .id_table = pdc_sata_pci_tbl, + .probe = pdc_sata_init_one, + .remove = ata_pci_remove_one, +}; + + +static void pdc20621_host_stop(struct ata_host *host) +{ + struct pci_dev *pdev = to_pci_dev(host->dev); + struct pdc_host_priv *hpriv = host->private_data; + void __iomem *dimm_mmio = hpriv->dimm_mmio; + + pci_iounmap(pdev, dimm_mmio); + kfree(hpriv); + + pci_iounmap(pdev, host->mmio_base); +} + +static int pdc_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct pdc_port_priv *pp; + int rc; + + rc = ata_port_start(ap); + if (rc) + return rc; + + pp = kmalloc(sizeof(*pp), GFP_KERNEL); + if (!pp) { + rc = -ENOMEM; + goto err_out; + } + memset(pp, 0, sizeof(*pp)); + + pp->pkt = dma_alloc_coherent(dev, 128, &pp->pkt_dma, GFP_KERNEL); + if (!pp->pkt) { + rc = -ENOMEM; + goto err_out_kfree; + } + + ap->private_data = pp; + + return 0; + +err_out_kfree: + kfree(pp); +err_out: + ata_port_stop(ap); + return rc; +} + + +static void pdc_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host->dev; + struct pdc_port_priv *pp = ap->private_data; + + ap->private_data = NULL; + dma_free_coherent(dev, 128, pp->pkt, pp->pkt_dma); + kfree(pp); + ata_port_stop(ap); +} + + +static void pdc_20621_phy_reset (struct ata_port *ap) +{ + VPRINTK("ENTER\n"); + ap->cbl = ATA_CBL_SATA; + ata_port_probe(ap); + ata_bus_reset(ap); +} + +static inline void pdc20621_ata_sg(struct ata_taskfile *tf, u8 *buf, + unsigned int portno, + unsigned int total_len) +{ + u32 addr; + unsigned int dw = PDC_DIMM_APKT_PRD >> 2; + u32 *buf32 = (u32 *) buf; + + /* output ATA packet S/G table */ + addr = PDC_20621_DIMM_BASE + PDC_20621_DIMM_DATA + + (PDC_DIMM_DATA_STEP * portno); + VPRINTK("ATA sg addr 0x%x, %d\n", addr, addr); + buf32[dw] = cpu_to_le32(addr); + buf32[dw + 1] = cpu_to_le32(total_len | ATA_PRD_EOT); + + VPRINTK("ATA PSG @ %x == (0x%x, 0x%x)\n", + PDC_20621_DIMM_BASE + + (PDC_DIMM_WINDOW_STEP * portno) + + PDC_DIMM_APKT_PRD, + buf32[dw], buf32[dw + 1]); +} + +static inline void pdc20621_host_sg(struct ata_taskfile *tf, u8 *buf, + unsigned int portno, + unsigned int total_len) +{ + u32 addr; + unsigned int dw = PDC_DIMM_HPKT_PRD >> 2; + u32 *buf32 = (u32 *) buf; + + /* output Host DMA packet S/G table */ + addr = PDC_20621_DIMM_BASE + PDC_20621_DIMM_DATA + + (PDC_DIMM_DATA_STEP * portno); + + buf32[dw] = cpu_to_le32(addr); + buf32[dw + 1] = cpu_to_le32(total_len | ATA_PRD_EOT); + + VPRINTK("HOST PSG @ %x == (0x%x, 0x%x)\n", + PDC_20621_DIMM_BASE + + (PDC_DIMM_WINDOW_STEP * portno) + + PDC_DIMM_HPKT_PRD, + buf32[dw], buf32[dw + 1]); +} + +static inline unsigned int pdc20621_ata_pkt(struct ata_taskfile *tf, + unsigned int devno, u8 *buf, + unsigned int portno) +{ + unsigned int i, dw; + u32 *buf32 = (u32 *) buf; + u8 dev_reg; + + unsigned int dimm_sg = PDC_20621_DIMM_BASE + + (PDC_DIMM_WINDOW_STEP * portno) + + PDC_DIMM_APKT_PRD; + VPRINTK("ENTER, dimm_sg == 0x%x, %d\n", dimm_sg, dimm_sg); + + i = PDC_DIMM_ATA_PKT; + + /* + * Set up ATA packet + */ + if ((tf->protocol == ATA_PROT_DMA) && (!(tf->flags & ATA_TFLAG_WRITE))) + buf[i++] = PDC_PKT_READ; + else if (tf->protocol == ATA_PROT_NODATA) + buf[i++] = PDC_PKT_NODATA; + else + buf[i++] = 0; + buf[i++] = 0; /* reserved */ + buf[i++] = portno + 1; /* seq. id */ + buf[i++] = 0xff; /* delay seq. id */ + + /* dimm dma S/G, and next-pkt */ + dw = i >> 2; + if (tf->protocol == ATA_PROT_NODATA) + buf32[dw] = 0; + else + buf32[dw] = cpu_to_le32(dimm_sg); + buf32[dw + 1] = 0; + i += 8; + + if (devno == 0) + dev_reg = ATA_DEVICE_OBS; + else + dev_reg = ATA_DEVICE_OBS | ATA_DEV1; + + /* select device */ + buf[i++] = (1 << 5) | PDC_PKT_CLEAR_BSY | ATA_REG_DEVICE; + buf[i++] = dev_reg; + + /* device control register */ + buf[i++] = (1 << 5) | PDC_REG_DEVCTL; + buf[i++] = tf->ctl; + + return i; +} + +static inline void pdc20621_host_pkt(struct ata_taskfile *tf, u8 *buf, + unsigned int portno) +{ + unsigned int dw; + u32 tmp, *buf32 = (u32 *) buf; + + unsigned int host_sg = PDC_20621_DIMM_BASE + + (PDC_DIMM_WINDOW_STEP * portno) + + PDC_DIMM_HOST_PRD; + unsigned int dimm_sg = PDC_20621_DIMM_BASE + + (PDC_DIMM_WINDOW_STEP * portno) + + PDC_DIMM_HPKT_PRD; + VPRINTK("ENTER, dimm_sg == 0x%x, %d\n", dimm_sg, dimm_sg); + VPRINTK("host_sg == 0x%x, %d\n", host_sg, host_sg); + + dw = PDC_DIMM_HOST_PKT >> 2; + + /* + * Set up Host DMA packet + */ + if ((tf->protocol == ATA_PROT_DMA) && (!(tf->flags & ATA_TFLAG_WRITE))) + tmp = PDC_PKT_READ; + else + tmp = 0; + tmp |= ((portno + 1 + 4) << 16); /* seq. id */ + tmp |= (0xff << 24); /* delay seq. id */ + buf32[dw + 0] = cpu_to_le32(tmp); + buf32[dw + 1] = cpu_to_le32(host_sg); + buf32[dw + 2] = cpu_to_le32(dimm_sg); + buf32[dw + 3] = 0; + + VPRINTK("HOST PKT @ %x == (0x%x 0x%x 0x%x 0x%x)\n", + PDC_20621_DIMM_BASE + (PDC_DIMM_WINDOW_STEP * portno) + + PDC_DIMM_HOST_PKT, + buf32[dw + 0], + buf32[dw + 1], + buf32[dw + 2], + buf32[dw + 3]); +} + +static void pdc20621_dma_prep(struct ata_queued_cmd *qc) +{ + struct scatterlist *sg; + struct ata_port *ap = qc->ap; + struct pdc_port_priv *pp = ap->private_data; + void __iomem *mmio = ap->host->mmio_base; + struct pdc_host_priv *hpriv = ap->host->private_data; + void __iomem *dimm_mmio = hpriv->dimm_mmio; + unsigned int portno = ap->port_no; + unsigned int i, idx, total_len = 0, sgt_len; + u32 *buf = (u32 *) &pp->dimm_buf[PDC_DIMM_HEADER_SZ]; + + WARN_ON(!(qc->flags & ATA_QCFLAG_DMAMAP)); + + VPRINTK("ata%u: ENTER\n", ap->id); + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + /* + * Build S/G table + */ + idx = 0; + ata_for_each_sg(sg, qc) { + buf[idx++] = cpu_to_le32(sg_dma_address(sg)); + buf[idx++] = cpu_to_le32(sg_dma_len(sg)); + total_len += sg_dma_len(sg); + } + buf[idx - 1] |= cpu_to_le32(ATA_PRD_EOT); + sgt_len = idx * 4; + + /* + * Build ATA, host DMA packets + */ + pdc20621_host_sg(&qc->tf, &pp->dimm_buf[0], portno, total_len); + pdc20621_host_pkt(&qc->tf, &pp->dimm_buf[0], portno); + + pdc20621_ata_sg(&qc->tf, &pp->dimm_buf[0], portno, total_len); + i = pdc20621_ata_pkt(&qc->tf, qc->dev->devno, &pp->dimm_buf[0], portno); + + if (qc->tf.flags & ATA_TFLAG_LBA48) + i = pdc_prep_lba48(&qc->tf, &pp->dimm_buf[0], i); + else + i = pdc_prep_lba28(&qc->tf, &pp->dimm_buf[0], i); + + pdc_pkt_footer(&qc->tf, &pp->dimm_buf[0], i); + + /* copy three S/G tables and two packets to DIMM MMIO window */ + memcpy_toio(dimm_mmio + (portno * PDC_DIMM_WINDOW_STEP), + &pp->dimm_buf, PDC_DIMM_HEADER_SZ); + memcpy_toio(dimm_mmio + (portno * PDC_DIMM_WINDOW_STEP) + + PDC_DIMM_HOST_PRD, + &pp->dimm_buf[PDC_DIMM_HEADER_SZ], sgt_len); + + /* force host FIFO dump */ + writel(0x00000001, mmio + PDC_20621_GENERAL_CTL); + + readl(dimm_mmio); /* MMIO PCI posting flush */ + + VPRINTK("ata pkt buf ofs %u, prd size %u, mmio copied\n", i, sgt_len); +} + +static void pdc20621_nodata_prep(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pdc_port_priv *pp = ap->private_data; + void __iomem *mmio = ap->host->mmio_base; + struct pdc_host_priv *hpriv = ap->host->private_data; + void __iomem *dimm_mmio = hpriv->dimm_mmio; + unsigned int portno = ap->port_no; + unsigned int i; + + VPRINTK("ata%u: ENTER\n", ap->id); + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + i = pdc20621_ata_pkt(&qc->tf, qc->dev->devno, &pp->dimm_buf[0], portno); + + if (qc->tf.flags & ATA_TFLAG_LBA48) + i = pdc_prep_lba48(&qc->tf, &pp->dimm_buf[0], i); + else + i = pdc_prep_lba28(&qc->tf, &pp->dimm_buf[0], i); + + pdc_pkt_footer(&qc->tf, &pp->dimm_buf[0], i); + + /* copy three S/G tables and two packets to DIMM MMIO window */ + memcpy_toio(dimm_mmio + (portno * PDC_DIMM_WINDOW_STEP), + &pp->dimm_buf, PDC_DIMM_HEADER_SZ); + + /* force host FIFO dump */ + writel(0x00000001, mmio + PDC_20621_GENERAL_CTL); + + readl(dimm_mmio); /* MMIO PCI posting flush */ + + VPRINTK("ata pkt buf ofs %u, mmio copied\n", i); +} + +static void pdc20621_qc_prep(struct ata_queued_cmd *qc) +{ + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + pdc20621_dma_prep(qc); + break; + case ATA_PROT_NODATA: + pdc20621_nodata_prep(qc); + break; + default: + break; + } +} + +static void __pdc20621_push_hdma(struct ata_queued_cmd *qc, + unsigned int seq, + u32 pkt_ofs) +{ + struct ata_port *ap = qc->ap; + struct ata_host *host = ap->host; + void __iomem *mmio = host->mmio_base; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + writel(0x00000001, mmio + PDC_20621_SEQCTL + (seq * 4)); + readl(mmio + PDC_20621_SEQCTL + (seq * 4)); /* flush */ + + writel(pkt_ofs, mmio + PDC_HDMA_PKT_SUBMIT); + readl(mmio + PDC_HDMA_PKT_SUBMIT); /* flush */ +} + +static void pdc20621_push_hdma(struct ata_queued_cmd *qc, + unsigned int seq, + u32 pkt_ofs) +{ + struct ata_port *ap = qc->ap; + struct pdc_host_priv *pp = ap->host->private_data; + unsigned int idx = pp->hdma_prod & PDC_HDMA_Q_MASK; + + if (!pp->doing_hdma) { + __pdc20621_push_hdma(qc, seq, pkt_ofs); + pp->doing_hdma = 1; + return; + } + + pp->hdma[idx].qc = qc; + pp->hdma[idx].seq = seq; + pp->hdma[idx].pkt_ofs = pkt_ofs; + pp->hdma_prod++; +} + +static void pdc20621_pop_hdma(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pdc_host_priv *pp = ap->host->private_data; + unsigned int idx = pp->hdma_cons & PDC_HDMA_Q_MASK; + + /* if nothing on queue, we're done */ + if (pp->hdma_prod == pp->hdma_cons) { + pp->doing_hdma = 0; + return; + } + + __pdc20621_push_hdma(pp->hdma[idx].qc, pp->hdma[idx].seq, + pp->hdma[idx].pkt_ofs); + pp->hdma_cons++; +} + +#ifdef ATA_VERBOSE_DEBUG +static void pdc20621_dump_hdma(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + unsigned int port_no = ap->port_no; + struct pdc_host_priv *hpriv = ap->host->private_data; + void *dimm_mmio = hpriv->dimm_mmio; + + dimm_mmio += (port_no * PDC_DIMM_WINDOW_STEP); + dimm_mmio += PDC_DIMM_HOST_PKT; + + printk(KERN_ERR "HDMA[0] == 0x%08X\n", readl(dimm_mmio)); + printk(KERN_ERR "HDMA[1] == 0x%08X\n", readl(dimm_mmio + 4)); + printk(KERN_ERR "HDMA[2] == 0x%08X\n", readl(dimm_mmio + 8)); + printk(KERN_ERR "HDMA[3] == 0x%08X\n", readl(dimm_mmio + 12)); +} +#else +static inline void pdc20621_dump_hdma(struct ata_queued_cmd *qc) { } +#endif /* ATA_VERBOSE_DEBUG */ + +static void pdc20621_packet_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_host *host = ap->host; + unsigned int port_no = ap->port_no; + void __iomem *mmio = host->mmio_base; + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u8 seq = (u8) (port_no + 1); + unsigned int port_ofs; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + VPRINTK("ata%u: ENTER\n", ap->id); + + wmb(); /* flush PRD, pkt writes */ + + port_ofs = PDC_20621_DIMM_BASE + (PDC_DIMM_WINDOW_STEP * port_no); + + /* if writing, we (1) DMA to DIMM, then (2) do ATA command */ + if (rw && qc->tf.protocol == ATA_PROT_DMA) { + seq += 4; + + pdc20621_dump_hdma(qc); + pdc20621_push_hdma(qc, seq, port_ofs + PDC_DIMM_HOST_PKT); + VPRINTK("queued ofs 0x%x (%u), seq %u\n", + port_ofs + PDC_DIMM_HOST_PKT, + port_ofs + PDC_DIMM_HOST_PKT, + seq); + } else { + writel(0x00000001, mmio + PDC_20621_SEQCTL + (seq * 4)); + readl(mmio + PDC_20621_SEQCTL + (seq * 4)); /* flush */ + + writel(port_ofs + PDC_DIMM_ATA_PKT, + (void __iomem *) ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); + readl((void __iomem *) ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); + VPRINTK("submitted ofs 0x%x (%u), seq %u\n", + port_ofs + PDC_DIMM_ATA_PKT, + port_ofs + PDC_DIMM_ATA_PKT, + seq); + } +} + +static unsigned int pdc20621_qc_issue_prot(struct ata_queued_cmd *qc) +{ + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + case ATA_PROT_NODATA: + pdc20621_packet_start(qc); + return 0; + + case ATA_PROT_ATAPI_DMA: + BUG(); + break; + + default: + break; + } + + return ata_qc_issue_prot(qc); +} + +static inline unsigned int pdc20621_host_intr( struct ata_port *ap, + struct ata_queued_cmd *qc, + unsigned int doing_hdma, + void __iomem *mmio) +{ + unsigned int port_no = ap->port_no; + unsigned int port_ofs = + PDC_20621_DIMM_BASE + (PDC_DIMM_WINDOW_STEP * port_no); + u8 status; + unsigned int handled = 0; + + VPRINTK("ENTER\n"); + + if ((qc->tf.protocol == ATA_PROT_DMA) && /* read */ + (!(qc->tf.flags & ATA_TFLAG_WRITE))) { + + /* step two - DMA from DIMM to host */ + if (doing_hdma) { + VPRINTK("ata%u: read hdma, 0x%x 0x%x\n", ap->id, + readl(mmio + 0x104), readl(mmio + PDC_HDMA_CTLSTAT)); + /* get drive status; clear intr; complete txn */ + qc->err_mask |= ac_err_mask(ata_wait_idle(ap)); + ata_qc_complete(qc); + pdc20621_pop_hdma(qc); + } + + /* step one - exec ATA command */ + else { + u8 seq = (u8) (port_no + 1 + 4); + VPRINTK("ata%u: read ata, 0x%x 0x%x\n", ap->id, + readl(mmio + 0x104), readl(mmio + PDC_HDMA_CTLSTAT)); + + /* submit hdma pkt */ + pdc20621_dump_hdma(qc); + pdc20621_push_hdma(qc, seq, + port_ofs + PDC_DIMM_HOST_PKT); + } + handled = 1; + + } else if (qc->tf.protocol == ATA_PROT_DMA) { /* write */ + + /* step one - DMA from host to DIMM */ + if (doing_hdma) { + u8 seq = (u8) (port_no + 1); + VPRINTK("ata%u: write hdma, 0x%x 0x%x\n", ap->id, + readl(mmio + 0x104), readl(mmio + PDC_HDMA_CTLSTAT)); + + /* submit ata pkt */ + writel(0x00000001, mmio + PDC_20621_SEQCTL + (seq * 4)); + readl(mmio + PDC_20621_SEQCTL + (seq * 4)); + writel(port_ofs + PDC_DIMM_ATA_PKT, + (void __iomem *) ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); + readl((void __iomem *) ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); + } + + /* step two - execute ATA command */ + else { + VPRINTK("ata%u: write ata, 0x%x 0x%x\n", ap->id, + readl(mmio + 0x104), readl(mmio + PDC_HDMA_CTLSTAT)); + /* get drive status; clear intr; complete txn */ + qc->err_mask |= ac_err_mask(ata_wait_idle(ap)); + ata_qc_complete(qc); + pdc20621_pop_hdma(qc); + } + handled = 1; + + /* command completion, but no data xfer */ + } else if (qc->tf.protocol == ATA_PROT_NODATA) { + + status = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000); + DPRINTK("BUS_NODATA (drv_stat 0x%X)\n", status); + qc->err_mask |= ac_err_mask(status); + ata_qc_complete(qc); + handled = 1; + + } else { + ap->stats.idle_irq++; + } + + return handled; +} + +static void pdc20621_irq_clear(struct ata_port *ap) +{ + struct ata_host *host = ap->host; + void __iomem *mmio = host->mmio_base; + + mmio += PDC_CHIP0_OFS; + + readl(mmio + PDC_20621_SEQMASK); +} + +static irqreturn_t pdc20621_interrupt (int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + struct ata_port *ap; + u32 mask = 0; + unsigned int i, tmp, port_no; + unsigned int handled = 0; + void __iomem *mmio_base; + + VPRINTK("ENTER\n"); + + if (!host || !host->mmio_base) { + VPRINTK("QUICK EXIT\n"); + return IRQ_NONE; + } + + mmio_base = host->mmio_base; + + /* reading should also clear interrupts */ + mmio_base += PDC_CHIP0_OFS; + mask = readl(mmio_base + PDC_20621_SEQMASK); + VPRINTK("mask == 0x%x\n", mask); + + if (mask == 0xffffffff) { + VPRINTK("QUICK EXIT 2\n"); + return IRQ_NONE; + } + mask &= 0xffff; /* only 16 tags possible */ + if (!mask) { + VPRINTK("QUICK EXIT 3\n"); + return IRQ_NONE; + } + + spin_lock(&host->lock); + + for (i = 1; i < 9; i++) { + port_no = i - 1; + if (port_no > 3) + port_no -= 4; + if (port_no >= host->n_ports) + ap = NULL; + else + ap = host->ports[port_no]; + tmp = mask & (1 << i); + VPRINTK("seq %u, port_no %u, ap %p, tmp %x\n", i, port_no, ap, tmp); + if (tmp && ap && + !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) + handled += pdc20621_host_intr(ap, qc, (i > 4), + mmio_base); + } + } + + spin_unlock(&host->lock); + + VPRINTK("mask == 0x%x\n", mask); + + VPRINTK("EXIT\n"); + + return IRQ_RETVAL(handled); +} + +static void pdc_eng_timeout(struct ata_port *ap) +{ + u8 drv_stat; + struct ata_host *host = ap->host; + struct ata_queued_cmd *qc; + unsigned long flags; + + DPRINTK("ENTER\n"); + + spin_lock_irqsave(&host->lock, flags); + + qc = ata_qc_from_tag(ap, ap->active_tag); + + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + case ATA_PROT_NODATA: + ata_port_printk(ap, KERN_ERR, "command timeout\n"); + qc->err_mask |= __ac_err_mask(ata_wait_idle(ap)); + break; + + default: + drv_stat = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000); + + ata_port_printk(ap, KERN_ERR, + "unknown timeout, cmd 0x%x stat 0x%x\n", + qc->tf.command, drv_stat); + + qc->err_mask |= ac_err_mask(drv_stat); + break; + } + + spin_unlock_irqrestore(&host->lock, flags); + ata_eh_qc_complete(qc); + DPRINTK("EXIT\n"); +} + +static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + WARN_ON (tf->protocol == ATA_PROT_DMA || + tf->protocol == ATA_PROT_NODATA); + ata_tf_load(ap, tf); +} + + +static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf) +{ + WARN_ON (tf->protocol == ATA_PROT_DMA || + tf->protocol == ATA_PROT_NODATA); + ata_exec_command(ap, tf); +} + + +static void pdc_sata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = base; + port->data_addr = base; + port->feature_addr = + port->error_addr = base + 0x4; + port->nsect_addr = base + 0x8; + port->lbal_addr = base + 0xc; + port->lbam_addr = base + 0x10; + port->lbah_addr = base + 0x14; + port->device_addr = base + 0x18; + port->command_addr = + port->status_addr = base + 0x1c; + port->altstatus_addr = + port->ctl_addr = base + 0x38; +} + + +#ifdef ATA_VERBOSE_DEBUG +static void pdc20621_get_from_dimm(struct ata_probe_ent *pe, void *psource, + u32 offset, u32 size) +{ + u32 window_size; + u16 idx; + u8 page_mask; + long dist; + void __iomem *mmio = pe->mmio_base; + struct pdc_host_priv *hpriv = pe->private_data; + void __iomem *dimm_mmio = hpriv->dimm_mmio; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + page_mask = 0x00; + window_size = 0x2000 * 4; /* 32K byte uchar size */ + idx = (u16) (offset / window_size); + + writel(0x01, mmio + PDC_GENERAL_CTLR); + readl(mmio + PDC_GENERAL_CTLR); + writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR); + readl(mmio + PDC_DIMM_WINDOW_CTLR); + + offset -= (idx * window_size); + idx++; + dist = ((long) (window_size - (offset + size))) >= 0 ? size : + (long) (window_size - offset); + memcpy_fromio((char *) psource, (char *) (dimm_mmio + offset / 4), + dist); + + psource += dist; + size -= dist; + for (; (long) size >= (long) window_size ;) { + writel(0x01, mmio + PDC_GENERAL_CTLR); + readl(mmio + PDC_GENERAL_CTLR); + writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR); + readl(mmio + PDC_DIMM_WINDOW_CTLR); + memcpy_fromio((char *) psource, (char *) (dimm_mmio), + window_size / 4); + psource += window_size; + size -= window_size; + idx ++; + } + + if (size) { + writel(0x01, mmio + PDC_GENERAL_CTLR); + readl(mmio + PDC_GENERAL_CTLR); + writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR); + readl(mmio + PDC_DIMM_WINDOW_CTLR); + memcpy_fromio((char *) psource, (char *) (dimm_mmio), + size / 4); + } +} +#endif + + +static void pdc20621_put_to_dimm(struct ata_probe_ent *pe, void *psource, + u32 offset, u32 size) +{ + u32 window_size; + u16 idx; + u8 page_mask; + long dist; + void __iomem *mmio = pe->mmio_base; + struct pdc_host_priv *hpriv = pe->private_data; + void __iomem *dimm_mmio = hpriv->dimm_mmio; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + page_mask = 0x00; + window_size = 0x2000 * 4; /* 32K byte uchar size */ + idx = (u16) (offset / window_size); + + writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR); + readl(mmio + PDC_DIMM_WINDOW_CTLR); + offset -= (idx * window_size); + idx++; + dist = ((long)(s32)(window_size - (offset + size))) >= 0 ? size : + (long) (window_size - offset); + memcpy_toio(dimm_mmio + offset / 4, psource, dist); + writel(0x01, mmio + PDC_GENERAL_CTLR); + readl(mmio + PDC_GENERAL_CTLR); + + psource += dist; + size -= dist; + for (; (long) size >= (long) window_size ;) { + writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR); + readl(mmio + PDC_DIMM_WINDOW_CTLR); + memcpy_toio(dimm_mmio, psource, window_size / 4); + writel(0x01, mmio + PDC_GENERAL_CTLR); + readl(mmio + PDC_GENERAL_CTLR); + psource += window_size; + size -= window_size; + idx ++; + } + + if (size) { + writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR); + readl(mmio + PDC_DIMM_WINDOW_CTLR); + memcpy_toio(dimm_mmio, psource, size / 4); + writel(0x01, mmio + PDC_GENERAL_CTLR); + readl(mmio + PDC_GENERAL_CTLR); + } +} + + +static unsigned int pdc20621_i2c_read(struct ata_probe_ent *pe, u32 device, + u32 subaddr, u32 *pdata) +{ + void __iomem *mmio = pe->mmio_base; + u32 i2creg = 0; + u32 status; + u32 count =0; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + i2creg |= device << 24; + i2creg |= subaddr << 16; + + /* Set the device and subaddress */ + writel(i2creg, mmio + PDC_I2C_ADDR_DATA_OFFSET); + readl(mmio + PDC_I2C_ADDR_DATA_OFFSET); + + /* Write Control to perform read operation, mask int */ + writel(PDC_I2C_READ | PDC_I2C_START | PDC_I2C_MASK_INT, + mmio + PDC_I2C_CONTROL_OFFSET); + + for (count = 0; count <= 1000; count ++) { + status = readl(mmio + PDC_I2C_CONTROL_OFFSET); + if (status & PDC_I2C_COMPLETE) { + status = readl(mmio + PDC_I2C_ADDR_DATA_OFFSET); + break; + } else if (count == 1000) + return 0; + } + + *pdata = (status >> 8) & 0x000000ff; + return 1; +} + + +static int pdc20621_detect_dimm(struct ata_probe_ent *pe) +{ + u32 data=0 ; + if (pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS, + PDC_DIMM_SPD_SYSTEM_FREQ, &data)) { + if (data == 100) + return 100; + } else + return 0; + + if (pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS, 9, &data)) { + if(data <= 0x75) + return 133; + } else + return 0; + + return 0; +} + + +static int pdc20621_prog_dimm0(struct ata_probe_ent *pe) +{ + u32 spd0[50]; + u32 data = 0; + int size, i; + u8 bdimmsize; + void __iomem *mmio = pe->mmio_base; + static const struct { + unsigned int reg; + unsigned int ofs; + } pdc_i2c_read_data [] = { + { PDC_DIMM_SPD_TYPE, 11 }, + { PDC_DIMM_SPD_FRESH_RATE, 12 }, + { PDC_DIMM_SPD_COLUMN_NUM, 4 }, + { PDC_DIMM_SPD_ATTRIBUTE, 21 }, + { PDC_DIMM_SPD_ROW_NUM, 3 }, + { PDC_DIMM_SPD_BANK_NUM, 17 }, + { PDC_DIMM_SPD_MODULE_ROW, 5 }, + { PDC_DIMM_SPD_ROW_PRE_CHARGE, 27 }, + { PDC_DIMM_SPD_ROW_ACTIVE_DELAY, 28 }, + { PDC_DIMM_SPD_RAS_CAS_DELAY, 29 }, + { PDC_DIMM_SPD_ACTIVE_PRECHARGE, 30 }, + { PDC_DIMM_SPD_CAS_LATENCY, 18 }, + }; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + for(i=0; i<ARRAY_SIZE(pdc_i2c_read_data); i++) + pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS, + pdc_i2c_read_data[i].reg, + &spd0[pdc_i2c_read_data[i].ofs]); + + data |= (spd0[4] - 8) | ((spd0[21] != 0) << 3) | ((spd0[3]-11) << 4); + data |= ((spd0[17] / 4) << 6) | ((spd0[5] / 2) << 7) | + ((((spd0[27] + 9) / 10) - 1) << 8) ; + data |= (((((spd0[29] > spd0[28]) + ? spd0[29] : spd0[28]) + 9) / 10) - 1) << 10; + data |= ((spd0[30] - spd0[29] + 9) / 10 - 2) << 12; + + if (spd0[18] & 0x08) + data |= ((0x03) << 14); + else if (spd0[18] & 0x04) + data |= ((0x02) << 14); + else if (spd0[18] & 0x01) + data |= ((0x01) << 14); + else + data |= (0 << 14); + + /* + Calculate the size of bDIMMSize (power of 2) and + merge the DIMM size by program start/end address. + */ + + bdimmsize = spd0[4] + (spd0[5] / 2) + spd0[3] + (spd0[17] / 2) + 3; + size = (1 << bdimmsize) >> 20; /* size = xxx(MB) */ + data |= (((size / 16) - 1) << 16); + data |= (0 << 23); + data |= 8; + writel(data, mmio + PDC_DIMM0_CONTROL_OFFSET); + readl(mmio + PDC_DIMM0_CONTROL_OFFSET); + return size; +} + + +static unsigned int pdc20621_prog_dimm_global(struct ata_probe_ent *pe) +{ + u32 data, spd0; + int error, i; + void __iomem *mmio = pe->mmio_base; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + /* + Set To Default : DIMM Module Global Control Register (0x022259F1) + DIMM Arbitration Disable (bit 20) + DIMM Data/Control Output Driving Selection (bit12 - bit15) + Refresh Enable (bit 17) + */ + + data = 0x022259F1; + writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET); + readl(mmio + PDC_SDRAM_CONTROL_OFFSET); + + /* Turn on for ECC */ + pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS, + PDC_DIMM_SPD_TYPE, &spd0); + if (spd0 == 0x02) { + data |= (0x01 << 16); + writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET); + readl(mmio + PDC_SDRAM_CONTROL_OFFSET); + printk(KERN_ERR "Local DIMM ECC Enabled\n"); + } + + /* DIMM Initialization Select/Enable (bit 18/19) */ + data &= (~(1<<18)); + data |= (1<<19); + writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET); + + error = 1; + for (i = 1; i <= 10; i++) { /* polling ~5 secs */ + data = readl(mmio + PDC_SDRAM_CONTROL_OFFSET); + if (!(data & (1<<19))) { + error = 0; + break; + } + msleep(i*100); + } + return error; +} + + +static unsigned int pdc20621_dimm_init(struct ata_probe_ent *pe) +{ + int speed, size, length; + u32 addr,spd0,pci_status; + u32 tmp=0; + u32 time_period=0; + u32 tcount=0; + u32 ticks=0; + u32 clock=0; + u32 fparam=0; + void __iomem *mmio = pe->mmio_base; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + /* Initialize PLL based upon PCI Bus Frequency */ + + /* Initialize Time Period Register */ + writel(0xffffffff, mmio + PDC_TIME_PERIOD); + time_period = readl(mmio + PDC_TIME_PERIOD); + VPRINTK("Time Period Register (0x40): 0x%x\n", time_period); + + /* Enable timer */ + writel(0x00001a0, mmio + PDC_TIME_CONTROL); + readl(mmio + PDC_TIME_CONTROL); + + /* Wait 3 seconds */ + msleep(3000); + + /* + When timer is enabled, counter is decreased every internal + clock cycle. + */ + + tcount = readl(mmio + PDC_TIME_COUNTER); + VPRINTK("Time Counter Register (0x44): 0x%x\n", tcount); + + /* + If SX4 is on PCI-X bus, after 3 seconds, the timer counter + register should be >= (0xffffffff - 3x10^8). + */ + if(tcount >= PCI_X_TCOUNT) { + ticks = (time_period - tcount); + VPRINTK("Num counters 0x%x (%d)\n", ticks, ticks); + + clock = (ticks / 300000); + VPRINTK("10 * Internal clk = 0x%x (%d)\n", clock, clock); + + clock = (clock * 33); + VPRINTK("10 * Internal clk * 33 = 0x%x (%d)\n", clock, clock); + + /* PLL F Param (bit 22:16) */ + fparam = (1400000 / clock) - 2; + VPRINTK("PLL F Param: 0x%x (%d)\n", fparam, fparam); + + /* OD param = 0x2 (bit 31:30), R param = 0x5 (bit 29:25) */ + pci_status = (0x8a001824 | (fparam << 16)); + } else + pci_status = PCI_PLL_INIT; + + /* Initialize PLL. */ + VPRINTK("pci_status: 0x%x\n", pci_status); + writel(pci_status, mmio + PDC_CTL_STATUS); + readl(mmio + PDC_CTL_STATUS); + + /* + Read SPD of DIMM by I2C interface, + and program the DIMM Module Controller. + */ + if (!(speed = pdc20621_detect_dimm(pe))) { + printk(KERN_ERR "Detect Local DIMM Fail\n"); + return 1; /* DIMM error */ + } + VPRINTK("Local DIMM Speed = %d\n", speed); + + /* Programming DIMM0 Module Control Register (index_CID0:80h) */ + size = pdc20621_prog_dimm0(pe); + VPRINTK("Local DIMM Size = %dMB\n",size); + + /* Programming DIMM Module Global Control Register (index_CID0:88h) */ + if (pdc20621_prog_dimm_global(pe)) { + printk(KERN_ERR "Programming DIMM Module Global Control Register Fail\n"); + return 1; + } + +#ifdef ATA_VERBOSE_DEBUG + { + u8 test_parttern1[40] = {0x55,0xAA,'P','r','o','m','i','s','e',' ', + 'N','o','t',' ','Y','e','t',' ','D','e','f','i','n','e','d',' ', + '1','.','1','0', + '9','8','0','3','1','6','1','2',0,0}; + u8 test_parttern2[40] = {0}; + + pdc20621_put_to_dimm(pe, (void *) test_parttern2, 0x10040, 40); + pdc20621_put_to_dimm(pe, (void *) test_parttern2, 0x40, 40); + + pdc20621_put_to_dimm(pe, (void *) test_parttern1, 0x10040, 40); + pdc20621_get_from_dimm(pe, (void *) test_parttern2, 0x40, 40); + printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0], + test_parttern2[1], &(test_parttern2[2])); + pdc20621_get_from_dimm(pe, (void *) test_parttern2, 0x10040, + 40); + printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0], + test_parttern2[1], &(test_parttern2[2])); + + pdc20621_put_to_dimm(pe, (void *) test_parttern1, 0x40, 40); + pdc20621_get_from_dimm(pe, (void *) test_parttern2, 0x40, 40); + printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0], + test_parttern2[1], &(test_parttern2[2])); + } +#endif + + /* ECC initiliazation. */ + + pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS, + PDC_DIMM_SPD_TYPE, &spd0); + if (spd0 == 0x02) { + VPRINTK("Start ECC initialization\n"); + addr = 0; + length = size * 1024 * 1024; + while (addr < length) { + pdc20621_put_to_dimm(pe, (void *) &tmp, addr, + sizeof(u32)); + addr += sizeof(u32); + } + VPRINTK("Finish ECC initialization\n"); + } + return 0; +} + + +static void pdc_20621_init(struct ata_probe_ent *pe) +{ + u32 tmp; + void __iomem *mmio = pe->mmio_base; + + /* hard-code chip #0 */ + mmio += PDC_CHIP0_OFS; + + /* + * Select page 0x40 for our 32k DIMM window + */ + tmp = readl(mmio + PDC_20621_DIMM_WINDOW) & 0xffff0000; + tmp |= PDC_PAGE_WINDOW; /* page 40h; arbitrarily selected */ + writel(tmp, mmio + PDC_20621_DIMM_WINDOW); + + /* + * Reset Host DMA + */ + tmp = readl(mmio + PDC_HDMA_CTLSTAT); + tmp |= PDC_RESET; + writel(tmp, mmio + PDC_HDMA_CTLSTAT); + readl(mmio + PDC_HDMA_CTLSTAT); /* flush */ + + udelay(10); + + tmp = readl(mmio + PDC_HDMA_CTLSTAT); + tmp &= ~PDC_RESET; + writel(tmp, mmio + PDC_HDMA_CTLSTAT); + readl(mmio + PDC_HDMA_CTLSTAT); /* flush */ +} + +static int pdc_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + unsigned long base; + void __iomem *mmio_base; + void __iomem *dimm_mmio = NULL; + struct pdc_host_priv *hpriv = NULL; + unsigned int board_idx = (unsigned int) ent->driver_data; + int pci_dev_busy = 0; + int rc; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, 3, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + base = (unsigned long) mmio_base; + + hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL); + if (!hpriv) { + rc = -ENOMEM; + goto err_out_iounmap; + } + memset(hpriv, 0, sizeof(*hpriv)); + + dimm_mmio = pci_iomap(pdev, 4, 0); + if (!dimm_mmio) { + kfree(hpriv); + rc = -ENOMEM; + goto err_out_iounmap; + } + + hpriv->dimm_mmio = dimm_mmio; + + probe_ent->sht = pdc_port_info[board_idx].sht; + probe_ent->port_flags = pdc_port_info[board_idx].flags; + probe_ent->pio_mask = pdc_port_info[board_idx].pio_mask; + probe_ent->mwdma_mask = pdc_port_info[board_idx].mwdma_mask; + probe_ent->udma_mask = pdc_port_info[board_idx].udma_mask; + probe_ent->port_ops = pdc_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + + probe_ent->private_data = hpriv; + base += PDC_CHIP0_OFS; + + probe_ent->n_ports = 4; + pdc_sata_setup_port(&probe_ent->port[0], base + 0x200); + pdc_sata_setup_port(&probe_ent->port[1], base + 0x280); + pdc_sata_setup_port(&probe_ent->port[2], base + 0x300); + pdc_sata_setup_port(&probe_ent->port[3], base + 0x380); + + pci_set_master(pdev); + + /* initialize adapter */ + /* initialize local dimm */ + if (pdc20621_dimm_init(probe_ent)) { + rc = -ENOMEM; + goto err_out_iounmap_dimm; + } + pdc_20621_init(probe_ent); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_iounmap_dimm: /* only get to this label if 20621 */ + kfree(hpriv); + pci_iounmap(pdev, dimm_mmio); +err_out_iounmap: + pci_iounmap(pdev, mmio_base); +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; +} + + +static int __init pdc_sata_init(void) +{ + return pci_register_driver(&pdc_sata_pci_driver); +} + + +static void __exit pdc_sata_exit(void) +{ + pci_unregister_driver(&pdc_sata_pci_driver); +} + + +MODULE_AUTHOR("Jeff Garzik"); +MODULE_DESCRIPTION("Promise SATA low-level driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pdc_sata_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_init(pdc_sata_init); +module_exit(pdc_sata_exit); diff --git a/drivers/ata/sata_uli.c b/drivers/ata/sata_uli.c new file mode 100644 index 00000000000..dd76f37be18 --- /dev/null +++ b/drivers/ata/sata_uli.c @@ -0,0 +1,300 @@ +/* + * sata_uli.c - ULi Electronics SATA + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available under NDA. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "sata_uli" +#define DRV_VERSION "1.0" + +enum { + uli_5289 = 0, + uli_5287 = 1, + uli_5281 = 2, + + uli_max_ports = 4, + + /* PCI configuration registers */ + ULI5287_BASE = 0x90, /* sata0 phy SCR registers */ + ULI5287_OFFS = 0x10, /* offset from sata0->sata1 phy regs */ + ULI5281_BASE = 0x60, /* sata0 phy SCR registers */ + ULI5281_OFFS = 0x60, /* offset from sata0->sata1 phy regs */ +}; + +struct uli_priv { + unsigned int scr_cfg_addr[uli_max_ports]; +}; + +static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); + +static const struct pci_device_id uli_pci_tbl[] = { + { PCI_VENDOR_ID_AL, 0x5289, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5289 }, + { PCI_VENDOR_ID_AL, 0x5287, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5287 }, + { PCI_VENDOR_ID_AL, 0x5281, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5281 }, + { } /* terminate list */ +}; + + +static struct pci_driver uli_pci_driver = { + .name = DRV_NAME, + .id_table = uli_pci_tbl, + .probe = uli_init_one, + .remove = ata_pci_remove_one, +}; + +static struct scsi_host_template uli_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations uli_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .scr_read = uli_scr_read, + .scr_write = uli_scr_write, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static struct ata_port_info uli_port_info = { + .sht = &uli_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY, + .pio_mask = 0x1f, /* pio0-4 */ + .udma_mask = 0x7f, /* udma0-6 */ + .port_ops = &uli_ops, +}; + + +MODULE_AUTHOR("Peer Chen"); +MODULE_DESCRIPTION("low-level driver for ULi Electronics SATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, uli_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg) +{ + struct uli_priv *hpriv = ap->host->private_data; + return hpriv->scr_cfg_addr[ap->port_no] + (4 * sc_reg); +} + +static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg); + u32 val; + + pci_read_config_dword(pdev, cfg_addr, &val); + return val; +} + +static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned int cfg_addr = get_scr_cfg_addr(ap, scr); + + pci_write_config_dword(pdev, cfg_addr, val); +} + +static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + if (sc_reg > SCR_CONTROL) + return 0xffffffffU; + + return uli_scr_cfg_read(ap, sc_reg); +} + +static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val) +{ + if (sc_reg > SCR_CONTROL) //SCR_CONTROL=2, SCR_ERROR=1, SCR_STATUS=0 + return; + + uli_scr_cfg_write(ap, sc_reg, val); +} + +static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent; + struct ata_port_info *ppi[2]; + int rc; + unsigned int board_idx = (unsigned int) ent->driver_data; + int pci_dev_busy = 0; + struct uli_priv *hpriv; + + if (!printed_version++) + dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + ppi[0] = ppi[1] = &uli_port_info; + probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY); + if (!probe_ent) { + rc = -ENOMEM; + goto err_out_regions; + } + + hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL); + if (!hpriv) { + rc = -ENOMEM; + goto err_out_probe_ent; + } + + probe_ent->private_data = hpriv; + + switch (board_idx) { + case uli_5287: + hpriv->scr_cfg_addr[0] = ULI5287_BASE; + hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS; + probe_ent->n_ports = 4; + + probe_ent->port[2].cmd_addr = pci_resource_start(pdev, 0) + 8; + probe_ent->port[2].altstatus_addr = + probe_ent->port[2].ctl_addr = + (pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS) + 4; + probe_ent->port[2].bmdma_addr = pci_resource_start(pdev, 4) + 16; + hpriv->scr_cfg_addr[2] = ULI5287_BASE + ULI5287_OFFS*4; + + probe_ent->port[3].cmd_addr = pci_resource_start(pdev, 2) + 8; + probe_ent->port[3].altstatus_addr = + probe_ent->port[3].ctl_addr = + (pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS) + 4; + probe_ent->port[3].bmdma_addr = pci_resource_start(pdev, 4) + 24; + hpriv->scr_cfg_addr[3] = ULI5287_BASE + ULI5287_OFFS*5; + + ata_std_ports(&probe_ent->port[2]); + ata_std_ports(&probe_ent->port[3]); + break; + + case uli_5289: + hpriv->scr_cfg_addr[0] = ULI5287_BASE; + hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS; + break; + + case uli_5281: + hpriv->scr_cfg_addr[0] = ULI5281_BASE; + hpriv->scr_cfg_addr[1] = ULI5281_BASE + ULI5281_OFFS; + break; + + default: + BUG(); + break; + } + + pci_set_master(pdev); + pci_intx(pdev, 1); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_probe_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; + +} + +static int __init uli_init(void) +{ + return pci_register_driver(&uli_pci_driver); +} + +static void __exit uli_exit(void) +{ + pci_unregister_driver(&uli_pci_driver); +} + + +module_init(uli_init); +module_exit(uli_exit); diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c new file mode 100644 index 00000000000..a72a2389a11 --- /dev/null +++ b/drivers/ata/sata_via.c @@ -0,0 +1,503 @@ +/* + * sata_via.c - VIA Serial ATA controllers + * + * Maintained by: Jeff Garzik <jgarzik@pobox.com> + * Please ALWAYS copy linux-ide@vger.kernel.org + on emails. + * + * Copyright 2003-2004 Red Hat, Inc. All rights reserved. + * Copyright 2003-2004 Jeff Garzik + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Hardware documentation available under NDA. + * + * + * To-do list: + * - VT6421 PATA support + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <asm/io.h> + +#define DRV_NAME "sata_via" +#define DRV_VERSION "2.0" + +enum board_ids_enum { + vt6420, + vt6421, +}; + +enum { + SATA_CHAN_ENAB = 0x40, /* SATA channel enable */ + SATA_INT_GATE = 0x41, /* SATA interrupt gating */ + SATA_NATIVE_MODE = 0x42, /* Native mode enable */ + SATA_PATA_SHARING = 0x49, /* PATA/SATA sharing func ctrl */ + + PORT0 = (1 << 1), + PORT1 = (1 << 0), + ALL_PORTS = PORT0 | PORT1, + N_PORTS = 2, + + NATIVE_MODE_ALL = (1 << 7) | (1 << 6) | (1 << 5) | (1 << 4), + + SATA_EXT_PHY = (1 << 6), /* 0==use PATA, 1==ext phy */ + SATA_2DEV = (1 << 5), /* SATA is master/slave */ +}; + +static int svia_init_one (struct pci_dev *pdev, const struct pci_device_id *ent); +static u32 svia_scr_read (struct ata_port *ap, unsigned int sc_reg); +static void svia_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val); +static void vt6420_error_handler(struct ata_port *ap); + +static const struct pci_device_id svia_pci_tbl[] = { + { 0x1106, 0x0591, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6420 }, + { 0x1106, 0x3149, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6420 }, + { 0x1106, 0x3249, PCI_ANY_ID, PCI_ANY_ID, 0, 0, vt6421 }, + + { } /* terminate list */ +}; + +static struct pci_driver svia_pci_driver = { + .name = DRV_NAME, + .id_table = svia_pci_tbl, + .probe = svia_init_one, + .remove = ata_pci_remove_one, +}; + +static struct scsi_host_template svia_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + +static const struct ata_port_operations vt6420_sata_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = vt6420_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static const struct ata_port_operations vt6421_sata_ops = { + .port_disable = ata_port_disable, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_pio_data_xfer, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .scr_read = svia_scr_read, + .scr_write = svia_scr_write, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop, +}; + +static struct ata_port_info vt6420_port_info = { + .sht = &svia_sht, + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &vt6420_sata_ops, +}; + +MODULE_AUTHOR("Jeff Garzik"); +MODULE_DESCRIPTION("SCSI low-level driver for VIA SATA controllers"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, svia_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +static u32 svia_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + if (sc_reg > SCR_CONTROL) + return 0xffffffffU; + return inl(ap->ioaddr.scr_addr + (4 * sc_reg)); +} + +static void svia_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val) +{ + if (sc_reg > SCR_CONTROL) + return; + outl(val, ap->ioaddr.scr_addr + (4 * sc_reg)); +} + +/** + * vt6420_prereset - prereset for vt6420 + * @ap: target ATA port + * + * SCR registers on vt6420 are pieces of shit and may hang the + * whole machine completely if accessed with the wrong timing. + * To avoid such catastrophe, vt6420 doesn't provide generic SCR + * access operations, but uses SStatus and SControl only during + * boot probing in controlled way. + * + * As the old (pre EH update) probing code is proven to work, we + * strictly follow the access pattern. + * + * LOCKING: + * Kernel thread context (may sleep) + * + * RETURNS: + * 0 on success, -errno otherwise. + */ +static int vt6420_prereset(struct ata_port *ap) +{ + struct ata_eh_context *ehc = &ap->eh_context; + unsigned long timeout = jiffies + (HZ * 5); + u32 sstatus, scontrol; + int online; + + /* don't do any SCR stuff if we're not loading */ + if (!ATA_PFLAG_LOADING) + goto skip_scr; + + /* Resume phy. This is the old resume sequence from + * __sata_phy_reset(). + */ + svia_scr_write(ap, SCR_CONTROL, 0x300); + svia_scr_read(ap, SCR_CONTROL); /* flush */ + + /* wait for phy to become ready, if necessary */ + do { + msleep(200); + if ((svia_scr_read(ap, SCR_STATUS) & 0xf) != 1) + break; + } while (time_before(jiffies, timeout)); + + /* open code sata_print_link_status() */ + sstatus = svia_scr_read(ap, SCR_STATUS); + scontrol = svia_scr_read(ap, SCR_CONTROL); + + online = (sstatus & 0xf) == 0x3; + + ata_port_printk(ap, KERN_INFO, + "SATA link %s 1.5 Gbps (SStatus %X SControl %X)\n", + online ? "up" : "down", sstatus, scontrol); + + /* SStatus is read one more time */ + svia_scr_read(ap, SCR_STATUS); + + if (!online) { + /* tell EH to bail */ + ehc->i.action &= ~ATA_EH_RESET_MASK; + return 0; + } + + skip_scr: + /* wait for !BSY */ + ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT); + + return 0; +} + +static void vt6420_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, vt6420_prereset, ata_std_softreset, + NULL, ata_std_postreset); +} + +static const unsigned int svia_bar_sizes[] = { + 8, 4, 8, 4, 16, 256 +}; + +static const unsigned int vt6421_bar_sizes[] = { + 16, 16, 16, 16, 32, 128 +}; + +static unsigned long svia_scr_addr(unsigned long addr, unsigned int port) +{ + return addr + (port * 128); +} + +static unsigned long vt6421_scr_addr(unsigned long addr, unsigned int port) +{ + return addr + (port * 64); +} + +static void vt6421_init_addrs(struct ata_probe_ent *probe_ent, + struct pci_dev *pdev, + unsigned int port) +{ + unsigned long reg_addr = pci_resource_start(pdev, port); + unsigned long bmdma_addr = pci_resource_start(pdev, 4) + (port * 8); + unsigned long scr_addr; + + probe_ent->port[port].cmd_addr = reg_addr; + probe_ent->port[port].altstatus_addr = + probe_ent->port[port].ctl_addr = (reg_addr + 8) | ATA_PCI_CTL_OFS; + probe_ent->port[port].bmdma_addr = bmdma_addr; + + scr_addr = vt6421_scr_addr(pci_resource_start(pdev, 5), port); + probe_ent->port[port].scr_addr = scr_addr; + + ata_std_ports(&probe_ent->port[port]); +} + +static struct ata_probe_ent *vt6420_init_probe_ent(struct pci_dev *pdev) +{ + struct ata_probe_ent *probe_ent; + struct ata_port_info *ppi[2]; + + ppi[0] = ppi[1] = &vt6420_port_info; + probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY); + if (!probe_ent) + return NULL; + + probe_ent->port[0].scr_addr = + svia_scr_addr(pci_resource_start(pdev, 5), 0); + probe_ent->port[1].scr_addr = + svia_scr_addr(pci_resource_start(pdev, 5), 1); + + return probe_ent; +} + +static struct ata_probe_ent *vt6421_init_probe_ent(struct pci_dev *pdev) +{ + struct ata_probe_ent *probe_ent; + unsigned int i; + + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (!probe_ent) + return NULL; + + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + probe_ent->sht = &svia_sht; + probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY; + probe_ent->port_ops = &vt6421_sata_ops; + probe_ent->n_ports = N_PORTS; + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->pio_mask = 0x1f; + probe_ent->mwdma_mask = 0x07; + probe_ent->udma_mask = 0x7f; + + for (i = 0; i < N_PORTS; i++) + vt6421_init_addrs(probe_ent, pdev, i); + + return probe_ent; +} + +static void svia_configure(struct pci_dev *pdev) +{ + u8 tmp8; + + pci_read_config_byte(pdev, PCI_INTERRUPT_LINE, &tmp8); + dev_printk(KERN_INFO, &pdev->dev, "routed to hard irq line %d\n", + (int) (tmp8 & 0xf0) == 0xf0 ? 0 : tmp8 & 0x0f); + + /* make sure SATA channels are enabled */ + pci_read_config_byte(pdev, SATA_CHAN_ENAB, &tmp8); + if ((tmp8 & ALL_PORTS) != ALL_PORTS) { + dev_printk(KERN_DEBUG, &pdev->dev, + "enabling SATA channels (0x%x)\n", + (int) tmp8); + tmp8 |= ALL_PORTS; + pci_write_config_byte(pdev, SATA_CHAN_ENAB, tmp8); + } + + /* make sure interrupts for each channel sent to us */ + pci_read_config_byte(pdev, SATA_INT_GATE, &tmp8); + if ((tmp8 & ALL_PORTS) != ALL_PORTS) { + dev_printk(KERN_DEBUG, &pdev->dev, + "enabling SATA channel interrupts (0x%x)\n", + (int) tmp8); + tmp8 |= ALL_PORTS; + pci_write_config_byte(pdev, SATA_INT_GATE, tmp8); + } + + /* make sure native mode is enabled */ + pci_read_config_byte(pdev, SATA_NATIVE_MODE, &tmp8); + if ((tmp8 & NATIVE_MODE_ALL) != NATIVE_MODE_ALL) { + dev_printk(KERN_DEBUG, &pdev->dev, + "enabling SATA channel native mode (0x%x)\n", + (int) tmp8); + tmp8 |= NATIVE_MODE_ALL; + pci_write_config_byte(pdev, SATA_NATIVE_MODE, tmp8); + } +} + +static int svia_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + unsigned int i; + int rc; + struct ata_probe_ent *probe_ent; + int board_id = (int) ent->driver_data; + const int *bar_sizes; + int pci_dev_busy = 0; + u8 tmp8; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + if (board_id == vt6420) { + pci_read_config_byte(pdev, SATA_PATA_SHARING, &tmp8); + if (tmp8 & SATA_2DEV) { + dev_printk(KERN_ERR, &pdev->dev, + "SATA master/slave not supported (0x%x)\n", + (int) tmp8); + rc = -EIO; + goto err_out_regions; + } + + bar_sizes = &svia_bar_sizes[0]; + } else { + bar_sizes = &vt6421_bar_sizes[0]; + } + + for (i = 0; i < ARRAY_SIZE(svia_bar_sizes); i++) + if ((pci_resource_start(pdev, i) == 0) || + (pci_resource_len(pdev, i) < bar_sizes[i])) { + dev_printk(KERN_ERR, &pdev->dev, + "invalid PCI BAR %u (sz 0x%llx, val 0x%llx)\n", + i, + (unsigned long long)pci_resource_start(pdev, i), + (unsigned long long)pci_resource_len(pdev, i)); + rc = -ENODEV; + goto err_out_regions; + } + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + goto err_out_regions; + + if (board_id == vt6420) + probe_ent = vt6420_init_probe_ent(pdev); + else + probe_ent = vt6421_init_probe_ent(pdev); + + if (!probe_ent) { + dev_printk(KERN_ERR, &pdev->dev, "out of memory\n"); + rc = -ENOMEM; + goto err_out_regions; + } + + svia_configure(pdev); + + pci_set_master(pdev); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; +} + +static int __init svia_init(void) +{ + return pci_register_driver(&svia_pci_driver); +} + +static void __exit svia_exit(void) +{ + pci_unregister_driver(&svia_pci_driver); +} + +module_init(svia_init); +module_exit(svia_exit); + diff --git a/drivers/ata/sata_vsc.c b/drivers/ata/sata_vsc.c new file mode 100644 index 00000000000..d0d92f33de5 --- /dev/null +++ b/drivers/ata/sata_vsc.c @@ -0,0 +1,482 @@ +/* + * sata_vsc.c - Vitesse VSC7174 4 port DPA SATA + * + * Maintained by: Jeremy Higdon @ SGI + * Please ALWAYS copy linux-ide@vger.kernel.org + * on emails. + * + * Copyright 2004 SGI + * + * Bits from Jeff Garzik, Copyright RedHat, Inc. + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. If not, write to + * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * libata documentation is available via 'make {ps|pdf}docs', + * as Documentation/DocBook/libata.* + * + * Vitesse hardware documentation presumably available under NDA. + * Intel 31244 (same hardware interface) documentation presumably + * available from http://developer.intel.com/ + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/dma-mapping.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "sata_vsc" +#define DRV_VERSION "2.0" + +enum { + /* Interrupt register offsets (from chip base address) */ + VSC_SATA_INT_STAT_OFFSET = 0x00, + VSC_SATA_INT_MASK_OFFSET = 0x04, + + /* Taskfile registers offsets */ + VSC_SATA_TF_CMD_OFFSET = 0x00, + VSC_SATA_TF_DATA_OFFSET = 0x00, + VSC_SATA_TF_ERROR_OFFSET = 0x04, + VSC_SATA_TF_FEATURE_OFFSET = 0x06, + VSC_SATA_TF_NSECT_OFFSET = 0x08, + VSC_SATA_TF_LBAL_OFFSET = 0x0c, + VSC_SATA_TF_LBAM_OFFSET = 0x10, + VSC_SATA_TF_LBAH_OFFSET = 0x14, + VSC_SATA_TF_DEVICE_OFFSET = 0x18, + VSC_SATA_TF_STATUS_OFFSET = 0x1c, + VSC_SATA_TF_COMMAND_OFFSET = 0x1d, + VSC_SATA_TF_ALTSTATUS_OFFSET = 0x28, + VSC_SATA_TF_CTL_OFFSET = 0x29, + + /* DMA base */ + VSC_SATA_UP_DESCRIPTOR_OFFSET = 0x64, + VSC_SATA_UP_DATA_BUFFER_OFFSET = 0x6C, + VSC_SATA_DMA_CMD_OFFSET = 0x70, + + /* SCRs base */ + VSC_SATA_SCR_STATUS_OFFSET = 0x100, + VSC_SATA_SCR_ERROR_OFFSET = 0x104, + VSC_SATA_SCR_CONTROL_OFFSET = 0x108, + + /* Port stride */ + VSC_SATA_PORT_OFFSET = 0x200, + + /* Error interrupt status bit offsets */ + VSC_SATA_INT_ERROR_CRC = 0x40, + VSC_SATA_INT_ERROR_T = 0x20, + VSC_SATA_INT_ERROR_P = 0x10, + VSC_SATA_INT_ERROR_R = 0x8, + VSC_SATA_INT_ERROR_E = 0x4, + VSC_SATA_INT_ERROR_M = 0x2, + VSC_SATA_INT_PHY_CHANGE = 0x1, + VSC_SATA_INT_ERROR = (VSC_SATA_INT_ERROR_CRC | VSC_SATA_INT_ERROR_T | \ + VSC_SATA_INT_ERROR_P | VSC_SATA_INT_ERROR_R | \ + VSC_SATA_INT_ERROR_E | VSC_SATA_INT_ERROR_M | \ + VSC_SATA_INT_PHY_CHANGE), +}; + + +#define is_vsc_sata_int_err(port_idx, int_status) \ + (int_status & (VSC_SATA_INT_ERROR << (8 * port_idx))) + + +static u32 vsc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg) +{ + if (sc_reg > SCR_CONTROL) + return 0xffffffffU; + return readl((void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + + +static void vsc_sata_scr_write (struct ata_port *ap, unsigned int sc_reg, + u32 val) +{ + if (sc_reg > SCR_CONTROL) + return; + writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4)); +} + + +static void vsc_intr_mask_update(struct ata_port *ap, u8 ctl) +{ + void __iomem *mask_addr; + u8 mask; + + mask_addr = ap->host->mmio_base + + VSC_SATA_INT_MASK_OFFSET + ap->port_no; + mask = readb(mask_addr); + if (ctl & ATA_NIEN) + mask |= 0x80; + else + mask &= 0x7F; + writeb(mask, mask_addr); +} + + +static void vsc_sata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; + + /* + * The only thing the ctl register is used for is SRST. + * That is not enabled or disabled via tf_load. + * However, if ATA_NIEN is changed, then we need to change the interrupt register. + */ + if ((tf->ctl & ATA_NIEN) != (ap->last_ctl & ATA_NIEN)) { + ap->last_ctl = tf->ctl; + vsc_intr_mask_update(ap, tf->ctl & ATA_NIEN); + } + if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { + writew(tf->feature | (((u16)tf->hob_feature) << 8), ioaddr->feature_addr); + writew(tf->nsect | (((u16)tf->hob_nsect) << 8), ioaddr->nsect_addr); + writew(tf->lbal | (((u16)tf->hob_lbal) << 8), ioaddr->lbal_addr); + writew(tf->lbam | (((u16)tf->hob_lbam) << 8), ioaddr->lbam_addr); + writew(tf->lbah | (((u16)tf->hob_lbah) << 8), ioaddr->lbah_addr); + } else if (is_addr) { + writew(tf->feature, ioaddr->feature_addr); + writew(tf->nsect, ioaddr->nsect_addr); + writew(tf->lbal, ioaddr->lbal_addr); + writew(tf->lbam, ioaddr->lbam_addr); + writew(tf->lbah, ioaddr->lbah_addr); + } + + if (tf->flags & ATA_TFLAG_DEVICE) + writeb(tf->device, ioaddr->device_addr); + + ata_wait_idle(ap); +} + + +static void vsc_sata_tf_read(struct ata_port *ap, struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + u16 nsect, lbal, lbam, lbah, feature; + + tf->command = ata_check_status(ap); + tf->device = readw(ioaddr->device_addr); + feature = readw(ioaddr->error_addr); + nsect = readw(ioaddr->nsect_addr); + lbal = readw(ioaddr->lbal_addr); + lbam = readw(ioaddr->lbam_addr); + lbah = readw(ioaddr->lbah_addr); + + tf->feature = feature; + tf->nsect = nsect; + tf->lbal = lbal; + tf->lbam = lbam; + tf->lbah = lbah; + + if (tf->flags & ATA_TFLAG_LBA48) { + tf->hob_feature = feature >> 8; + tf->hob_nsect = nsect >> 8; + tf->hob_lbal = lbal >> 8; + tf->hob_lbam = lbam >> 8; + tf->hob_lbah = lbah >> 8; + } +} + + +/* + * vsc_sata_interrupt + * + * Read the interrupt register and process for the devices that have them pending. + */ +static irqreturn_t vsc_sata_interrupt (int irq, void *dev_instance, + struct pt_regs *regs) +{ + struct ata_host *host = dev_instance; + unsigned int i; + unsigned int handled = 0; + u32 int_status; + + spin_lock(&host->lock); + + int_status = readl(host->mmio_base + VSC_SATA_INT_STAT_OFFSET); + + for (i = 0; i < host->n_ports; i++) { + if (int_status & ((u32) 0xFF << (8 * i))) { + struct ata_port *ap; + + ap = host->ports[i]; + + if (is_vsc_sata_int_err(i, int_status)) { + u32 err_status; + printk(KERN_DEBUG "%s: ignoring interrupt(s)\n", __FUNCTION__); + err_status = ap ? vsc_sata_scr_read(ap, SCR_ERROR) : 0; + vsc_sata_scr_write(ap, SCR_ERROR, err_status); + handled++; + } + + if (ap && !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + + qc = ata_qc_from_tag(ap, ap->active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING))) + handled += ata_host_intr(ap, qc); + else if (is_vsc_sata_int_err(i, int_status)) { + /* + * On some chips (i.e. Intel 31244), an error + * interrupt will sneak in at initialization + * time (phy state changes). Clearing the SCR + * error register is not required, but it prevents + * the phy state change interrupts from recurring + * later. + */ + u32 err_status; + err_status = vsc_sata_scr_read(ap, SCR_ERROR); + printk(KERN_DEBUG "%s: clearing interrupt, " + "status %x; sata err status %x\n", + __FUNCTION__, + int_status, err_status); + vsc_sata_scr_write(ap, SCR_ERROR, err_status); + /* Clear interrupt status */ + ata_chk_status(ap); + handled++; + } + } + } + } + + spin_unlock(&host->lock); + + return IRQ_RETVAL(handled); +} + + +static struct scsi_host_template vsc_sata_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, +}; + + +static const struct ata_port_operations vsc_sata_ops = { + .port_disable = ata_port_disable, + .tf_load = vsc_sata_tf_load, + .tf_read = vsc_sata_tf_read, + .exec_command = ata_exec_command, + .check_status = ata_check_status, + .dev_select = ata_std_dev_select, + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .data_xfer = ata_mmio_data_xfer, + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = ata_bmdma_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + .irq_handler = vsc_sata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + .scr_read = vsc_sata_scr_read, + .scr_write = vsc_sata_scr_write, + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_pci_host_stop, +}; + +static void __devinit vsc_sata_setup_port(struct ata_ioports *port, unsigned long base) +{ + port->cmd_addr = base + VSC_SATA_TF_CMD_OFFSET; + port->data_addr = base + VSC_SATA_TF_DATA_OFFSET; + port->error_addr = base + VSC_SATA_TF_ERROR_OFFSET; + port->feature_addr = base + VSC_SATA_TF_FEATURE_OFFSET; + port->nsect_addr = base + VSC_SATA_TF_NSECT_OFFSET; + port->lbal_addr = base + VSC_SATA_TF_LBAL_OFFSET; + port->lbam_addr = base + VSC_SATA_TF_LBAM_OFFSET; + port->lbah_addr = base + VSC_SATA_TF_LBAH_OFFSET; + port->device_addr = base + VSC_SATA_TF_DEVICE_OFFSET; + port->status_addr = base + VSC_SATA_TF_STATUS_OFFSET; + port->command_addr = base + VSC_SATA_TF_COMMAND_OFFSET; + port->altstatus_addr = base + VSC_SATA_TF_ALTSTATUS_OFFSET; + port->ctl_addr = base + VSC_SATA_TF_CTL_OFFSET; + port->bmdma_addr = base + VSC_SATA_DMA_CMD_OFFSET; + port->scr_addr = base + VSC_SATA_SCR_STATUS_OFFSET; + writel(0, base + VSC_SATA_UP_DESCRIPTOR_OFFSET); + writel(0, base + VSC_SATA_UP_DATA_BUFFER_OFFSET); +} + + +static int __devinit vsc_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + struct ata_probe_ent *probe_ent = NULL; + unsigned long base; + int pci_dev_busy = 0; + void __iomem *mmio_base; + int rc; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + /* + * Check if we have needed resource mapped. + */ + if (pci_resource_len(pdev, 0) == 0) { + rc = -ENODEV; + goto err_out; + } + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) { + pci_dev_busy = 1; + goto err_out; + } + + /* + * Use 32 bit DMA mask, because 64 bit address support is poor. + */ + rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) + goto err_out_regions; + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) + goto err_out_regions; + + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (probe_ent == NULL) { + rc = -ENOMEM; + goto err_out_regions; + } + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + mmio_base = pci_iomap(pdev, 0, 0); + if (mmio_base == NULL) { + rc = -ENOMEM; + goto err_out_free_ent; + } + base = (unsigned long) mmio_base; + + /* + * Due to a bug in the chip, the default cache line size can't be used + */ + pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x80); + + probe_ent->sht = &vsc_sata_sht; + probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO; + probe_ent->port_ops = &vsc_sata_ops; + probe_ent->n_ports = 4; + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->mmio_base = mmio_base; + + /* We don't care much about the PIO/UDMA masks, but the core won't like us + * if we don't fill these + */ + probe_ent->pio_mask = 0x1f; + probe_ent->mwdma_mask = 0x07; + probe_ent->udma_mask = 0x7f; + + /* We have 4 ports per PCI function */ + vsc_sata_setup_port(&probe_ent->port[0], base + 1 * VSC_SATA_PORT_OFFSET); + vsc_sata_setup_port(&probe_ent->port[1], base + 2 * VSC_SATA_PORT_OFFSET); + vsc_sata_setup_port(&probe_ent->port[2], base + 3 * VSC_SATA_PORT_OFFSET); + vsc_sata_setup_port(&probe_ent->port[3], base + 4 * VSC_SATA_PORT_OFFSET); + + pci_set_master(pdev); + + /* + * Config offset 0x98 is "Extended Control and Status Register 0" + * Default value is (1 << 28). All bits except bit 28 are reserved in + * DPA mode. If bit 28 is set, LED 0 reflects all ports' activity. + * If bit 28 is clear, each port has its own LED. + */ + pci_write_config_dword(pdev, 0x98, 0); + + /* FIXME: check ata_device_add return value */ + ata_device_add(probe_ent); + kfree(probe_ent); + + return 0; + +err_out_free_ent: + kfree(probe_ent); +err_out_regions: + pci_release_regions(pdev); +err_out: + if (!pci_dev_busy) + pci_disable_device(pdev); + return rc; +} + + +static const struct pci_device_id vsc_sata_pci_tbl[] = { + { PCI_VENDOR_ID_VITESSE, 0x7174, + PCI_ANY_ID, PCI_ANY_ID, 0x10600, 0xFFFFFF, 0 }, + { PCI_VENDOR_ID_INTEL, 0x3200, + PCI_ANY_ID, PCI_ANY_ID, 0x10600, 0xFFFFFF, 0 }, + { } /* terminate list */ +}; + + +static struct pci_driver vsc_sata_pci_driver = { + .name = DRV_NAME, + .id_table = vsc_sata_pci_tbl, + .probe = vsc_sata_init_one, + .remove = ata_pci_remove_one, +}; + + +static int __init vsc_sata_init(void) +{ + return pci_register_driver(&vsc_sata_pci_driver); +} + + +static void __exit vsc_sata_exit(void) +{ + pci_unregister_driver(&vsc_sata_pci_driver); +} + + +MODULE_AUTHOR("Jeremy Higdon"); +MODULE_DESCRIPTION("low-level driver for Vitesse VSC7174 SATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, vsc_sata_pci_tbl); +MODULE_VERSION(DRV_VERSION); + +module_init(vsc_sata_init); +module_exit(vsc_sata_exit); |