diff options
Diffstat (limited to 'drivers/block')
| -rw-r--r-- | drivers/block/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/block/Makefile | 1 | ||||
| -rw-r--r-- | drivers/block/nbd.c | 6 | ||||
| -rw-r--r-- | drivers/block/ps2esdi.c | 1079 |
4 files changed, 6 insertions, 1090 deletions
diff --git a/drivers/block/Kconfig b/drivers/block/Kconfig index b6d230b3209..0d1d2133d9b 100644 --- a/drivers/block/Kconfig +++ b/drivers/block/Kconfig @@ -44,16 +44,6 @@ config MAC_FLOPPY If you have a SWIM-3 (Super Woz Integrated Machine 3; from Apple) floppy controller, say Y here. Most commonly found in PowerMacs. -config BLK_DEV_PS2 - tristate "PS/2 ESDI hard disk support" - depends on MCA && MCA_LEGACY && BROKEN - help - Say Y here if you have a PS/2 machine with a MCA bus and an ESDI - hard disk. - - To compile this driver as a module, choose M here: the - module will be called ps2esdi. - config AMIGA_Z2RAM tristate "Amiga Zorro II ramdisk support" depends on ZORRO diff --git a/drivers/block/Makefile b/drivers/block/Makefile index 01c972415cb..5e584306be9 100644 --- a/drivers/block/Makefile +++ b/drivers/block/Makefile @@ -13,7 +13,6 @@ obj-$(CONFIG_ATARI_FLOPPY) += ataflop.o obj-$(CONFIG_AMIGA_Z2RAM) += z2ram.o obj-$(CONFIG_BLK_DEV_RAM) += brd.o obj-$(CONFIG_BLK_DEV_LOOP) += loop.o -obj-$(CONFIG_BLK_DEV_PS2) += ps2esdi.o obj-$(CONFIG_BLK_DEV_XD) += xd.o obj-$(CONFIG_BLK_CPQ_DA) += cpqarray.o obj-$(CONFIG_BLK_CPQ_CISS_DA) += cciss.o diff --git a/drivers/block/nbd.c b/drivers/block/nbd.c index b53fdb0a282..60cc54368b6 100644 --- a/drivers/block/nbd.c +++ b/drivers/block/nbd.c @@ -153,6 +153,12 @@ static int sock_xmit(struct nbd_device *lo, int send, void *buf, int size, struct kvec iov; sigset_t blocked, oldset; + if (unlikely(!sock)) { + printk(KERN_ERR "%s: Attempted %s on closed socket in sock_xmit\n", + lo->disk->disk_name, (send ? "send" : "recv")); + return -EINVAL; + } + /* Allow interception of SIGKILL only * Don't allow other signals to interrupt the transmission */ siginitsetinv(&blocked, sigmask(SIGKILL)); diff --git a/drivers/block/ps2esdi.c b/drivers/block/ps2esdi.c deleted file mode 100644 index 3c796e23625..00000000000 --- a/drivers/block/ps2esdi.c +++ /dev/null @@ -1,1079 +0,0 @@ -/* ps2esdi driver based on assembler code by Arindam Banerji, - written by Peter De Schrijver */ -/* Reassuring note to IBM : This driver was NOT developed by vice-versa - engineering the PS/2's BIOS */ -/* Dedicated to Wannes, Tofke, Ykke, Godot, Killroy and all those - other lovely fish out there... */ -/* This code was written during the long and boring WINA - elections 1994 */ -/* Thanks to Arindam Banerij for giving me the source of his driver */ -/* This code may be freely distributed and modified in any way, - as long as these notes remain intact */ - -/* Revised: 05/07/94 by Arindam Banerji (axb@cse.nd.edu) */ -/* Revised: 09/08/94 by Peter De Schrijver (stud11@cc4.kuleuven.ac.be) - Thanks to Arindam Banerij for sending me the docs of the adapter */ - -/* BA Modified for ThinkPad 720 by Boris Ashkinazi */ -/* (bash@vnet.ibm.com) 08/08/95 */ - -/* Modified further for ThinkPad-720C by Uri Blumenthal */ -/* (uri@watson.ibm.com) Sep 11, 1995 */ - -/* TODO : - + Timeouts - + Get disk parameters - + DMA above 16MB - + reset after read/write error - */ - -#define DEVICE_NAME "PS/2 ESDI" - -#include <linux/major.h> -#include <linux/errno.h> -#include <linux/wait.h> -#include <linux/interrupt.h> -#include <linux/fs.h> -#include <linux/kernel.h> -#include <linux/genhd.h> -#include <linux/ps2esdi.h> -#include <linux/blkdev.h> -#include <linux/mca-legacy.h> -#include <linux/init.h> -#include <linux/ioport.h> -#include <linux/module.h> -#include <linux/hdreg.h> - -#include <asm/system.h> -#include <asm/io.h> -#include <asm/dma.h> -#include <asm/mca_dma.h> -#include <asm/uaccess.h> - -#define PS2ESDI_IRQ 14 -#define MAX_HD 2 -#define MAX_RETRIES 5 -#define MAX_16BIT 65536 -#define ESDI_TIMEOUT 0xf000 -#define ESDI_STAT_TIMEOUT 4 - -#define TYPE_0_CMD_BLK_LENGTH 2 -#define TYPE_1_CMD_BLK_LENGTH 4 - -static void reset_ctrl(void); - -static int ps2esdi_geninit(void); - -static void do_ps2esdi_request(struct request_queue * q); - -static void ps2esdi_readwrite(int cmd, struct request *req); - -static void ps2esdi_fill_cmd_block(u_short * cmd_blk, u_short cmd, -u_short cyl, u_short head, u_short sector, u_short length, u_char drive); - -static int ps2esdi_out_cmd_blk(u_short * cmd_blk); - -static void ps2esdi_prep_dma(char *buffer, u_short length, u_char dma_xmode); - -static irqreturn_t ps2esdi_interrupt_handler(int irq, void *dev_id); -static void (*current_int_handler) (u_int) = NULL; -static void ps2esdi_normal_interrupt_handler(u_int); -static void ps2esdi_initial_reset_int_handler(u_int); -static void ps2esdi_geometry_int_handler(u_int); -static int ps2esdi_getgeo(struct block_device *bdev, struct hd_geometry *geo); - -static int ps2esdi_read_status_words(int num_words, int max_words, u_short * buffer); - -static void dump_cmd_complete_status(u_int int_ret_code); - -static void ps2esdi_get_device_cfg(void); - -static void ps2esdi_reset_timer(unsigned long unused); - -static u_int dma_arb_level; /* DMA arbitration level */ - -static DECLARE_WAIT_QUEUE_HEAD(ps2esdi_int); - -static int no_int_yet; -static int ps2esdi_drives; -static u_short io_base; -static DEFINE_TIMER(esdi_timer, ps2esdi_reset_timer, 0, 0); -static int reset_status; -static int ps2esdi_slot = -1; -static int tp720esdi = 0; /* Is it Integrated ESDI of ThinkPad-720? */ -static int intg_esdi = 0; /* If integrated adapter */ -struct ps2esdi_i_struct { - unsigned int head, sect, cyl, wpcom, lzone, ctl; -}; -static DEFINE_SPINLOCK(ps2esdi_lock); -static struct request_queue *ps2esdi_queue; -static struct request *current_req; - -#if 0 -#if 0 /* try both - I don't know which one is better... UB */ -static struct ps2esdi_i_struct ps2esdi_info[MAX_HD] = -{ - {4, 48, 1553, 0, 0, 0}, - {0, 0, 0, 0, 0, 0}}; -#else -static struct ps2esdi_i_struct ps2esdi_info[MAX_HD] = -{ - {64, 32, 161, 0, 0, 0}, - {0, 0, 0, 0, 0, 0}}; -#endif -#endif -static struct ps2esdi_i_struct ps2esdi_info[MAX_HD] = -{ - {0, 0, 0, 0, 0, 0}, - {0, 0, 0, 0, 0, 0}}; - -static struct block_device_operations ps2esdi_fops = -{ - .owner = THIS_MODULE, - .getgeo = ps2esdi_getgeo, -}; - -static struct gendisk *ps2esdi_gendisk[2]; - -/* initialization routine called by ll_rw_blk.c */ -static int __init ps2esdi_init(void) -{ - - int error = 0; - - /* register the device - pass the name and major number */ - if (register_blkdev(PS2ESDI_MAJOR, "ed")) - return -EBUSY; - - /* set up some global information - indicating device specific info */ - ps2esdi_queue = blk_init_queue(do_ps2esdi_request, &ps2esdi_lock); - if (!ps2esdi_queue) { - unregister_blkdev(PS2ESDI_MAJOR, "ed"); - return -ENOMEM; - } - - /* some minor housekeeping - setup the global gendisk structure */ - error = ps2esdi_geninit(); - if (error) { - printk(KERN_WARNING "PS2ESDI: error initialising" - " device, releasing resources\n"); - unregister_blkdev(PS2ESDI_MAJOR, "ed"); - blk_cleanup_queue(ps2esdi_queue); - return error; - } - return 0; -} /* ps2esdi_init */ - -#ifndef MODULE - -module_init(ps2esdi_init); - -#else - -static int cyl[MAX_HD] = {-1,-1}; -static int head[MAX_HD] = {-1, -1}; -static int sect[MAX_HD] = {-1, -1}; - -module_param(tp720esdi, bool, 0); -module_param_array(cyl, int, NULL, 0); -module_param_array(head, int, NULL, 0); -module_param_array(sect, int, NULL, 0); -MODULE_LICENSE("GPL"); - -int init_module(void) { - int drive; - - for(drive = 0; drive < MAX_HD; drive++) { - struct ps2esdi_i_struct *info = &ps2esdi_info[drive]; - - if (cyl[drive] != -1) { - info->cyl = info->lzone = cyl[drive]; - info->wpcom = 0; - } - if (head[drive] != -1) { - info->head = head[drive]; - info->ctl = (head[drive] > 8 ? 8 : 0); - } - if (sect[drive] != -1) info->sect = sect[drive]; - } - return ps2esdi_init(); -} - -void -cleanup_module(void) { - int i; - if(ps2esdi_slot) { - mca_mark_as_unused(ps2esdi_slot); - mca_set_adapter_procfn(ps2esdi_slot, NULL, NULL); - } - release_region(io_base, 4); - free_dma(dma_arb_level); - free_irq(PS2ESDI_IRQ, &ps2esdi_gendisk); - unregister_blkdev(PS2ESDI_MAJOR, "ed"); - blk_cleanup_queue(ps2esdi_queue); - for (i = 0; i < ps2esdi_drives; i++) { - del_gendisk(ps2esdi_gendisk[i]); - put_disk(ps2esdi_gendisk[i]); - } -} -#endif /* MODULE */ - -/* handles boot time command line parameters */ -void __init tp720_setup(char *str, int *ints) -{ - /* no params, just sets the tp720esdi flag if it exists */ - - printk("%s: TP 720 ESDI flag set\n", DEVICE_NAME); - tp720esdi = 1; -} - -void __init ed_setup(char *str, int *ints) -{ - int hdind = 0; - - /* handles 3 parameters only - corresponding to - 1. Number of cylinders - 2. Number of heads - 3. Sectors/track - */ - - if (ints[0] != 3) - return; - - /* print out the information - seen at boot time */ - printk("%s: ints[0]=%d ints[1]=%d ints[2]=%d ints[3]=%d\n", - DEVICE_NAME, ints[0], ints[1], ints[2], ints[3]); - - /* set the index into device specific information table */ - if (ps2esdi_info[0].head != 0) - hdind = 1; - - /* set up all the device information */ - ps2esdi_info[hdind].head = ints[2]; - ps2esdi_info[hdind].sect = ints[3]; - ps2esdi_info[hdind].cyl = ints[1]; - ps2esdi_info[hdind].wpcom = 0; - ps2esdi_info[hdind].lzone = ints[1]; - ps2esdi_info[hdind].ctl = (ints[2] > 8 ? 8 : 0); -#if 0 /* this may be needed for PS2/Mod.80, but it hurts ThinkPad! */ - ps2esdi_drives = hdind + 1; /* increment index for the next time */ -#endif -} /* ed_setup */ - -static int ps2esdi_getinfo(char *buf, int slot, void *d) -{ - int len = 0; - - len += sprintf(buf + len, "DMA Arbitration Level: %d\n", - dma_arb_level); - len += sprintf(buf + len, "IO Port: %x\n", io_base); - len += sprintf(buf + len, "IRQ: 14\n"); - len += sprintf(buf + len, "Drives: %d\n", ps2esdi_drives); - - return len; -} - -/* ps2 esdi specific initialization - called thru the gendisk chain */ -static int __init ps2esdi_geninit(void) -{ - /* - The first part contains the initialization code - for the ESDI disk subsystem. All we really do - is search for the POS registers of the controller - to do some simple setup operations. First, we - must ensure that the controller is installed, - enabled, and configured as PRIMARY. Then we must - determine the DMA arbitration level being used by - the controller so we can handle data transfer - operations properly. If all of this works, then - we will set the INIT_FLAG to a non-zero value. - */ - - int slot = 0, i, reset_start, reset_end; - u_char status; - unsigned short adapterID; - int error = 0; - - if ((slot = mca_find_adapter(INTG_ESDI_ID, 0)) != MCA_NOTFOUND) { - adapterID = INTG_ESDI_ID; - printk("%s: integrated ESDI adapter found in slot %d\n", - DEVICE_NAME, slot+1); -#ifndef MODULE - mca_set_adapter_name(slot, "PS/2 Integrated ESDI"); -#endif - } else if ((slot = mca_find_adapter(NRML_ESDI_ID, 0)) != -1) { - adapterID = NRML_ESDI_ID; - printk("%s: normal ESDI adapter found in slot %d\n", - DEVICE_NAME, slot+1); - mca_set_adapter_name(slot, "PS/2 ESDI"); - } else { - return -ENODEV; - } - - ps2esdi_slot = slot; - mca_mark_as_used(slot); - mca_set_adapter_procfn(slot, (MCA_ProcFn) ps2esdi_getinfo, NULL); - - /* Found the slot - read the POS register 2 to get the necessary - configuration and status information. POS register 2 has the - following information : - Bit Function - 7 reserved = 0 - 6 arbitration method - 0 - fairness enabled - 1 - fairness disabled, linear priority assignment - 5-2 arbitration level - 1 alternate address - 1 alternate address - 0 - use addresses 0x3510 - 0x3517 - 0 adapter enable - */ - - status = mca_read_stored_pos(slot, 2); - /* is it enabled ? */ - if (!(status & STATUS_ENABLED)) { - printk("%s: ESDI adapter disabled\n", DEVICE_NAME); - error = -ENODEV; - goto err_out1; - } - /* try to grab IRQ, and try to grab a slow IRQ if it fails, so we can - share with the SCSI driver */ - if (request_irq(PS2ESDI_IRQ, ps2esdi_interrupt_handler, - IRQF_DISABLED | IRQF_SHARED, "PS/2 ESDI", &ps2esdi_gendisk) - && request_irq(PS2ESDI_IRQ, ps2esdi_interrupt_handler, - IRQF_SHARED, "PS/2 ESDI", &ps2esdi_gendisk) - ) { - printk("%s: Unable to get IRQ %d\n", DEVICE_NAME, PS2ESDI_IRQ); - error = -EBUSY; - goto err_out1; - } - if (status & STATUS_ALTERNATE) - io_base = ALT_IO_BASE; - else - io_base = PRIMARY_IO_BASE; - - if (!request_region(io_base, 4, "ed")) { - printk(KERN_WARNING"Unable to request region 0x%x\n", io_base); - error = -EBUSY; - goto err_out2; - } - /* get the dma arbitration level */ - dma_arb_level = (status >> 2) & 0xf; - - /* BA */ - printk("%s: DMA arbitration level : %d\n", - DEVICE_NAME, dma_arb_level); - - LITE_ON; - current_int_handler = ps2esdi_initial_reset_int_handler; - reset_ctrl(); - reset_status = 0; - reset_start = jiffies; - while (!reset_status) { - init_timer(&esdi_timer); - esdi_timer.expires = jiffies + HZ; - esdi_timer.data = 0; - add_timer(&esdi_timer); - sleep_on(&ps2esdi_int); - } - reset_end = jiffies; - LITE_OFF; - printk("%s: reset interrupt after %d jiffies, %u.%02u secs\n", - DEVICE_NAME, reset_end - reset_start, (reset_end - reset_start) / HZ, - (reset_end - reset_start) % HZ); - - - /* Integrated ESDI Disk and Controller has only one drive! */ - if (adapterID == INTG_ESDI_ID) {/* if not "normal" PS2 ESDI adapter */ - ps2esdi_drives = 1; /* then we have only one physical disk! */ intg_esdi = 1; - } - - - - /* finally this part sets up some global data structures etc. */ - - ps2esdi_get_device_cfg(); - - /* some annoyance in the above routine returns TWO drives? - Is something else happining in the background? - Regaurdless we fix the # of drives again. AJK */ - /* Integrated ESDI Disk and Controller has only one drive! */ - if (adapterID == INTG_ESDI_ID) /* if not "normal" PS2 ESDI adapter */ - ps2esdi_drives = 1; /* Not three or two, ONE DAMNIT! */ - - current_int_handler = ps2esdi_normal_interrupt_handler; - - if (request_dma(dma_arb_level, "ed") !=0) { - printk(KERN_WARNING "PS2ESDI: Can't request dma-channel %d\n" - ,(int) dma_arb_level); - error = -EBUSY; - goto err_out3; - } - blk_queue_max_sectors(ps2esdi_queue, 128); - - error = -ENOMEM; - for (i = 0; i < ps2esdi_drives; i++) { - struct gendisk *disk = alloc_disk(64); - if (!disk) - goto err_out4; - disk->major = PS2ESDI_MAJOR; - disk->first_minor = i<<6; - sprintf(disk->disk_name, "ed%c", 'a'+i); - disk->fops = &ps2esdi_fops; - ps2esdi_gendisk[i] = disk; - } - - for (i = 0; i < ps2esdi_drives; i++) { - struct gendisk *disk = ps2esdi_gendisk[i]; - set_capacity(disk, ps2esdi_info[i].head * ps2esdi_info[i].sect * - ps2esdi_info[i].cyl); - disk->queue = ps2esdi_queue; - disk->private_data = &ps2esdi_info[i]; - add_disk(disk); - } - return 0; -err_out4: - while (i--) - put_disk(ps2esdi_gendisk[i]); -err_out3: - release_region(io_base, 4); -err_out2: - free_irq(PS2ESDI_IRQ, &ps2esdi_gendisk); -err_out1: - if(ps2esdi_slot) { - mca_mark_as_unused(ps2esdi_slot); - mca_set_adapter_procfn(ps2esdi_slot, NULL, NULL); - } - return error; -} - -static void __init ps2esdi_get_device_cfg(void) -{ - u_short cmd_blk[TYPE_0_CMD_BLK_LENGTH]; - - /*BA */ printk("%s: Drive 0\n", DEVICE_NAME); - current_int_handler = ps2esdi_geometry_int_handler; - cmd_blk[0] = CMD_GET_DEV_CONFIG | 0x600; - cmd_blk[1] = 0; - no_int_yet = TRUE; - ps2esdi_out_cmd_blk(cmd_blk); - if (no_int_yet) - sleep_on(&ps2esdi_int); - - if (ps2esdi_drives > 1) { - printk("%s: Drive 1\n", DEVICE_NAME); /*BA */ - cmd_blk[0] = CMD_GET_DEV_CONFIG | (1 << 5) | 0x600; - cmd_blk[1] = 0; - no_int_yet = TRUE; - ps2esdi_out_cmd_blk(cmd_blk); - if (no_int_yet) - sleep_on(&ps2esdi_int); - } /* if second physical drive is present */ - return; -} - -/* strategy routine that handles most of the IO requests */ -static void do_ps2esdi_request(struct request_queue * q) -{ - struct request *req; - /* since, this routine is called with interrupts cleared - they - must be before it finishes */ - - req = elv_next_request(q); - if (!req) - return; - -#if 0 - printk("%s:got request. device : %s command : %d sector : %ld count : %ld, buffer: %p\n", - DEVICE_NAME, - req->rq_disk->disk_name, - req->cmd, req->sector, - req->current_nr_sectors, req->buffer); -#endif - - /* check for above 16Mb dmas */ - if (isa_virt_to_bus(req->buffer + req->current_nr_sectors * 512) > 16 * MB) { - printk("%s: DMA above 16MB not supported\n", DEVICE_NAME); - end_request(req, FAIL); - return; - } - - if (req->sector+req->current_nr_sectors > get_capacity(req->rq_disk)) { - printk("Grrr. error. ps2esdi_drives: %d, %llu %llu\n", - ps2esdi_drives, req->sector, - (unsigned long long)get_capacity(req->rq_disk)); - end_request(req, FAIL); - return; - } - - switch (rq_data_dir(req)) { - case READ: - ps2esdi_readwrite(READ, req); - break; - case WRITE: - ps2esdi_readwrite(WRITE, req); - break; - default: - printk("%s: Unknown command\n", req->rq_disk->disk_name); - end_request(req, FAIL); - break; - } /* handle different commands */ -} /* main strategy routine */ - -/* resets the ESDI adapter */ -static void reset_ctrl(void) -{ - - u_long expire; - u_short status; - - /* enable interrupts on the controller */ - status = inb(ESDI_INTRPT); - outb((status & 0xe0) | ATT_EOI, ESDI_ATTN); /* to be sure we don't have - any interrupt pending... */ - outb_p(CTRL_ENABLE_INTR, ESDI_CONTROL); - - /* read the ESDI status port - if the controller is not busy, - simply do a soft reset (fast) - otherwise we'll have to do a - hard (slow) reset. */ - if (!(inb_p(ESDI_STATUS) & STATUS_BUSY)) { - /*BA */ printk("%s: soft reset...\n", DEVICE_NAME); - outb_p(CTRL_SOFT_RESET, ESDI_ATTN); - } - /* soft reset */ - else { - /*BA */ - printk("%s: hard reset...\n", DEVICE_NAME); - outb_p(CTRL_HARD_RESET, ESDI_CONTROL); - expire = jiffies + 2*HZ; - while (time_before(jiffies, expire)); - outb_p(1, ESDI_CONTROL); - } /* hard reset */ - - -} /* reset the controller */ - -/* called by the strategy routine to handle read and write requests */ -static void ps2esdi_readwrite(int cmd, struct request *req) -{ - struct ps2esdi_i_struct *p = req->rq_disk->private_data; - unsigned block = req->sector; - unsigned count = req->current_nr_sectors; - int drive = p - ps2esdi_info; - u_short track, head, cylinder, sector; - u_short cmd_blk[TYPE_1_CMD_BLK_LENGTH]; - - /* do some relevant arithmatic */ - track = block / p->sect; - head = track % p->head; - cylinder = track / p->head; - sector = block % p->sect; - -#if 0 - printk("%s: cyl=%d head=%d sect=%d\n", DEVICE_NAME, cylinder, head, sector); -#endif - /* call the routine that actually fills out a command block */ - ps2esdi_fill_cmd_block - (cmd_blk, - (cmd == READ) ? CMD_READ : CMD_WRITE, - cylinder, head, sector, count, drive); - - /* send the command block to the controller */ - current_req = req; - spin_unlock_irq(&ps2esdi_lock); - if (ps2esdi_out_cmd_blk(cmd_blk)) { - spin_lock_irq(&ps2esdi_lock); - printk("%s: Controller failed\n", DEVICE_NAME); - if ((++req->errors) >= MAX_RETRIES) - end_request(req, FAIL); - } - /* check for failure to put out the command block */ - else { - spin_lock_irq(&ps2esdi_lock); -#if 0 - printk("%s: waiting for xfer\n", DEVICE_NAME); -#endif - /* turn disk lights on */ - LITE_ON; - } - -} /* ps2esdi_readwrite */ - -/* fill out the command block */ -static void ps2esdi_fill_cmd_block(u_short * cmd_blk, u_short cmd, - u_short cyl, u_short head, u_short sector, u_short length, u_char drive) -{ - - cmd_blk[0] = (drive << 5) | cmd; - cmd_blk[1] = length; - cmd_blk[2] = ((cyl & 0x1f) << 11) | (head << 5) | sector; - cmd_blk[3] = (cyl & 0x3E0) >> 5; - -} /* fill out the command block */ - -/* write a command block to the controller */ -static int ps2esdi_out_cmd_blk(u_short * cmd_blk) -{ - - int i; - unsigned long jif; - u_char status; - - /* enable interrupts */ - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - - /* do not write to the controller, if it is busy */ - for (jif = jiffies + ESDI_STAT_TIMEOUT; - time_after(jif, jiffies) && - (inb(ESDI_STATUS) & STATUS_BUSY); ) - ; - -#if 0 - printk("%s: i(1)=%ld\n", DEVICE_NAME, jif); -#endif - - /* if device is still busy - then just time out */ - if (inb(ESDI_STATUS) & STATUS_BUSY) { - printk("%s: ps2esdi_out_cmd timed out (1)\n", DEVICE_NAME); - return ERROR; - } /* timeout ??? */ - /* Set up the attention register in the controller */ - outb(((*cmd_blk) & 0xE0) | 1, ESDI_ATTN); - -#if 0 - printk("%s: sending %d words to controller\n", DEVICE_NAME, (((*cmd_blk) >> 14) + 1) << 1); -#endif - - /* one by one send each word out */ - for (i = (((*cmd_blk) >> 14) + 1) << 1; i; i--) { - status = inb(ESDI_STATUS); - for (jif = jiffies + ESDI_STAT_TIMEOUT; - time_after(jif, jiffies) && (status & STATUS_BUSY) && - (status & STATUS_CMD_INF); status = inb(ESDI_STATUS)); - if ((status & (STATUS_BUSY | STATUS_CMD_INF)) == STATUS_BUSY) { -#if 0 - printk("%s: sending %04X\n", DEVICE_NAME, *cmd_blk); -#endif - outw(*cmd_blk++, ESDI_CMD_INT); - } else { - printk("%s: ps2esdi_out_cmd timed out while sending command (status=%02X)\n", - DEVICE_NAME, status); - return ERROR; - } - } /* send all words out */ - return OK; -} /* send out the commands */ - - -/* prepare for dma - do all the necessary setup */ -static void ps2esdi_prep_dma(char *buffer, u_short length, u_char dma_xmode) -{ - unsigned long flags = claim_dma_lock(); - - mca_disable_dma(dma_arb_level); - - mca_set_dma_addr(dma_arb_level, isa_virt_to_bus(buffer)); - - mca_set_dma_count(dma_arb_level, length * 512 / 2); - - mca_set_dma_mode(dma_arb_level, dma_xmode); - - mca_enable_dma(dma_arb_level); - - release_dma_lock(flags); - -} /* prepare for dma */ - - - -static irqreturn_t ps2esdi_interrupt_handler(int irq, void *dev_id) -{ - u_int int_ret_code; - - if (inb(ESDI_STATUS) & STATUS_INTR) { - int_ret_code = inb(ESDI_INTRPT); - if (current_int_handler) { - /* Disable adapter interrupts till processing is finished */ - outb(CTRL_DISABLE_INTR, ESDI_CONTROL); - current_int_handler(int_ret_code); - } else - printk("%s: help ! No interrupt handler.\n", DEVICE_NAME); - } else { - return IRQ_NONE; - } - return IRQ_HANDLED; -} - -static void ps2esdi_initial_reset_int_handler(u_int int_ret_code) -{ - - switch (int_ret_code & 0xf) { - case INT_RESET: - /*BA */ - printk("%s: initial reset completed.\n", DEVICE_NAME); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - wake_up(&ps2esdi_int); - break; - case INT_ATTN_ERROR: - printk("%s: Attention error. interrupt status : %02X\n", DEVICE_NAME, - int_ret_code); - printk("%s: status: %02x\n", DEVICE_NAME, inb(ESDI_STATUS)); - break; - default: - printk("%s: initial reset handler received interrupt: %02X\n", - DEVICE_NAME, int_ret_code); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - break; - } - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); -} - - -static void ps2esdi_geometry_int_handler(u_int int_ret_code) -{ - u_int status, drive_num; - unsigned long rba; - int i; - - drive_num = int_ret_code >> 5; - switch (int_ret_code & 0xf) { - case INT_CMD_COMPLETE: - for (i = ESDI_TIMEOUT; i && !(inb(ESDI_STATUS) & STATUS_STAT_AVAIL); i--); - if (!(inb(ESDI_STATUS) & STATUS_STAT_AVAIL)) { - printk("%s: timeout reading status word\n", DEVICE_NAME); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - break; - } - status = inw(ESDI_STT_INT); - if ((status & 0x1F) == CMD_GET_DEV_CONFIG) { -#define REPLY_WORDS 5 /* we already read word 0 */ - u_short reply[REPLY_WORDS]; - - if (ps2esdi_read_status_words((status >> 8) - 1, REPLY_WORDS, reply)) { - /*BA */ - printk("%s: Device Configuration Status for drive %u\n", - DEVICE_NAME, drive_num); - - printk("%s: Spares/cyls: %u", DEVICE_NAME, reply[0] >> 8); - - printk - ("Config bits: %s%s%s%s%s\n", - (reply[0] & CONFIG_IS) ? "Invalid Secondary, " : "", - ((reply[0] & CONFIG_ZD) && !(reply[0] & CONFIG_IS)) - ? "Zero Defect, " : "Defects Present, ", - (reply[0] & CONFIG_SF) ? "Skewed Format, " : "", - (reply[0] & CONFIG_FR) ? "Removable, " : "Non-Removable, ", - (reply[0] & CONFIG_RT) ? "No Retries" : "Retries"); - - rba = reply[1] | ((unsigned long) reply[2] << 16); - printk("%s: Number of RBA's: %lu\n", DEVICE_NAME, rba); - - printk("%s: Physical number of cylinders: %u, Sectors/Track: %u, Heads: %u\n", - DEVICE_NAME, reply[3], reply[4] >> 8, reply[4] & 0xff); - - if (!ps2esdi_info[drive_num].head) { - ps2esdi_info[drive_num].head = 64; - ps2esdi_info[drive_num].sect = 32; - ps2esdi_info[drive_num].cyl = rba / (64 * 32); - ps2esdi_info[drive_num].wpcom = 0; - ps2esdi_info[drive_num].lzone = ps2esdi_info[drive_num].cyl; - ps2esdi_info[drive_num].ctl = 8; - if (tp720esdi) { /* store the retrieved parameters */ - ps2esdi_info[0].head = reply[4] & 0Xff; - ps2esdi_info[0].sect = reply[4] >> 8; - ps2esdi_info[0].cyl = reply[3]; - ps2esdi_info[0].wpcom = 0; - ps2esdi_info[0].lzone = reply[3]; - } else { - if (!intg_esdi) - ps2esdi_drives++; - } - } -#ifdef OBSOLETE - if (!ps2esdi_info[drive_num].head) { - ps2esdi_info[drive_num].head = reply[4] & 0Xff; - ps2esdi_info[drive_num].sect = reply[4] >> 8; - ps2esdi_info[drive_num].cyl = reply[3]; - ps2esdi_info[drive_num].wpcom = 0; - ps2esdi_info[drive_num].lzone = reply[3]; - if (tp720esdi) { /* store the retrieved parameters */ - ps2esdi_info[0].head = reply[4] & 0Xff; - ps2esdi_info[0].sect = reply[4] >> 8; - ps2esdi_info[0].cyl = reply[3]; - ps2esdi_info[0].wpcom = 0; - ps2esdi_info[0].lzone = reply[3]; - } else { - ps2esdi_drives++; - } - } -#endif - - } else - printk("%s: failed while getting device config\n", DEVICE_NAME); -#undef REPLY_WORDS - } else - printk("%s: command %02X unknown by geometry handler\n", - DEVICE_NAME, status & 0x1f); - - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - break; - - case INT_ATTN_ERROR: - printk("%s: Attention error. interrupt status : %02X\n", DEVICE_NAME, - int_ret_code); - printk("%s: Device not available\n", DEVICE_NAME); - break; - case INT_CMD_ECC: - case INT_CMD_RETRY: - case INT_CMD_ECC_RETRY: - case INT_CMD_WARNING: - case INT_CMD_ABORT: - case INT_CMD_FAILED: - case INT_DMA_ERR: - case INT_CMD_BLK_ERR: - /*BA */ printk("%s: Whaa. Error occurred...\n", DEVICE_NAME); - dump_cmd_complete_status(int_ret_code); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - break; - default: - printk("%s: Unknown interrupt reason: %02X\n", - DEVICE_NAME, int_ret_code & 0xf); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - break; - } - - wake_up(&ps2esdi_int); - no_int_yet = FALSE; - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - -} - -static void ps2esdi_normal_interrupt_handler(u_int int_ret_code) -{ - unsigned long flags; - u_int status; - u_int ending; - int i; - - switch (int_ret_code & 0x0f) { - case INT_TRANSFER_REQ: - ps2esdi_prep_dma(current_req->buffer, - current_req->current_nr_sectors, - (rq_data_dir(current_req) == READ) - ? MCA_DMA_MODE_16 | MCA_DMA_MODE_WRITE | MCA_DMA_MODE_XFER - : MCA_DMA_MODE_16 | MCA_DMA_MODE_READ); - outb(CTRL_ENABLE_DMA | CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = -1; - break; - - case INT_ATTN_ERROR: - printk("%s: Attention error. interrupt status : %02X\n", DEVICE_NAME, - int_ret_code); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = FAIL; - break; - - case INT_CMD_COMPLETE: - for (i = ESDI_TIMEOUT; i && !(inb(ESDI_STATUS) & STATUS_STAT_AVAIL); i--); - if (!(inb(ESDI_STATUS) & STATUS_STAT_AVAIL)) { - printk("%s: timeout reading status word\n", DEVICE_NAME); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - if ((++current_req->errors) >= MAX_RETRIES) - ending = FAIL; - else - ending = -1; - break; - } - status = inw(ESDI_STT_INT); - switch (status & 0x1F) { - case (CMD_READ & 0xff): - case (CMD_WRITE & 0xff): - LITE_OFF; - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = SUCCES; - break; - default: - printk("%s: interrupt for unknown command %02X\n", - DEVICE_NAME, status & 0x1f); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = -1; - break; - } - break; - case INT_CMD_ECC: - case INT_CMD_RETRY: - case INT_CMD_ECC_RETRY: - LITE_OFF; - dump_cmd_complete_status(int_ret_code); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = SUCCES; - break; - case INT_CMD_WARNING: - case INT_CMD_ABORT: - case INT_CMD_FAILED: - case INT_DMA_ERR: - LITE_OFF; - dump_cmd_complete_status(int_ret_code); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - if ((++current_req->errors) >= MAX_RETRIES) - ending = FAIL; - else - ending = -1; - break; - - case INT_CMD_BLK_ERR: - dump_cmd_complete_status(int_ret_code); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = FAIL; - break; - - case INT_CMD_FORMAT: - printk("%s: huh ? Who issued this format command ?\n" - ,DEVICE_NAME); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = -1; - break; - - case INT_RESET: - /* BA printk("%s: reset completed.\n", DEVICE_NAME) */ ; - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = -1; - break; - - default: - printk("%s: Unknown interrupt reason: %02X\n", - DEVICE_NAME, int_ret_code & 0xf); - outb((int_ret_code & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - ending = -1; - break; - } - if(ending != -1) { - spin_lock_irqsave(&ps2esdi_lock, flags); - end_request(current_req, ending); - current_req = NULL; - do_ps2esdi_request(ps2esdi_queue); - spin_unlock_irqrestore(&ps2esdi_lock, flags); - } -} /* handle interrupts */ - - - -static int ps2esdi_read_status_words(int num_words, - int max_words, - u_short * buffer) -{ - int i; - - for (; max_words && num_words; max_words--, num_words--, buffer++) { - for (i = ESDI_TIMEOUT; i && !(inb(ESDI_STATUS) & STATUS_STAT_AVAIL); i--); - if (!(inb(ESDI_STATUS) & STATUS_STAT_AVAIL)) { - printk("%s: timeout reading status word\n", DEVICE_NAME); - return FAIL; - } - *buffer = inw(ESDI_STT_INT); - } - return SUCCES; -} - - - - -static void dump_cmd_complete_status(u_int int_ret_code) -{ -#define WAIT_FOR_STATUS \ - for(i=ESDI_TIMEOUT;i && !(inb(ESDI_STATUS) & STATUS_STAT_AVAIL);i--); \ - if(!(inb(ESDI_STATUS) & STATUS_STAT_AVAIL)) { \ - printk("%s: timeout reading status word\n",DEVICE_NAME); \ - return; \ - } - - int i, word_count; - u_short stat_word; - u_long rba; - - printk("%s: Device: %u, interrupt ID: %02X\n", - DEVICE_NAME, int_ret_code >> 5, - int_ret_code & 0xf); - - WAIT_FOR_STATUS; - stat_word = inw(ESDI_STT_INT); - word_count = (stat_word >> 8) - 1; - printk("%s: %u status words, command: %02X\n", DEVICE_NAME, word_count, - stat_word & 0xff); - - if (word_count--) { - WAIT_FOR_STATUS; - stat_word = inw(ESDI_STT_INT); - printk("%s: command status code: %02X, command error code: %02X\n", - DEVICE_NAME, stat_word >> 8, stat_word & 0xff); - } - if (word_count--) { - WAIT_FOR_STATUS; - stat_word = inw(ESDI_STT_INT); - printk("%s: device error code: %s%s%s%s%s,%02X\n", DEVICE_NAME, - (stat_word & 0x1000) ? "Ready, " : "Not Ready, ", - (stat_word & 0x0800) ? "Selected, " : "Not Selected, ", - (stat_word & 0x0400) ? "Write Fault, " : "", - (stat_word & 0x0200) ? "Track 0, " : "", - (stat_word & 0x0100) ? "Seek or command complete, " : "", - stat_word >> 8); - } - if (word_count--) { - WAIT_FOR_STATUS; - stat_word = inw(ESDI_STT_INT); - printk("%s: Blocks to do: %u", DEVICE_NAME, stat_word); - } - if (word_count -= 2) { - WAIT_FOR_STATUS; - rba = inw(ESDI_STT_INT); - WAIT_FOR_STATUS; - rba |= inw(ESDI_STT_INT) << 16; - printk(", Last Cyl: %u Head: %u Sector: %u\n", - (u_short) ((rba & 0x1ff80000) >> 11), - (u_short) ((rba & 0x7E0) >> 5), (u_short) (rba & 0x1f)); - } else - printk("\n"); - - if (word_count--) { - WAIT_FOR_STATUS; - stat_word = inw(ESDI_STT_INT); - printk("%s: Blocks required ECC: %u", DEVICE_NAME, stat_word); - } - printk("\n"); - -#undef WAIT_FOR_STATUS - -} - -static int ps2esdi_getgeo(struct block_device *bdev, struct hd_geometry *geo) -{ - struct ps2esdi_i_struct *p = bdev->bd_disk->private_data; - - geo->heads = p->head; - geo->sectors = p->sect; - geo->cylinders = p->cyl; - return 0; -} - -static void ps2esdi_reset_timer(unsigned long unused) -{ - - int status; - - status = inb(ESDI_INTRPT); - if ((status & 0xf) == INT_RESET) { - outb((status & 0xe0) | ATT_EOI, ESDI_ATTN); - outb(CTRL_ENABLE_INTR, ESDI_CONTROL); - reset_status = 1; - } - wake_up(&ps2esdi_int); -} |