diff options
Diffstat (limited to 'drivers/char/ftape/lowlevel/fc-10.c')
| -rw-r--r-- | drivers/char/ftape/lowlevel/fc-10.c | 175 |
1 files changed, 0 insertions, 175 deletions
diff --git a/drivers/char/ftape/lowlevel/fc-10.c b/drivers/char/ftape/lowlevel/fc-10.c deleted file mode 100644 index 9bc1cddade7..00000000000 --- a/drivers/char/ftape/lowlevel/fc-10.c +++ /dev/null @@ -1,175 +0,0 @@ -/* - * - - Copyright (C) 1993,1994 Jon Tombs. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - The entire guts of this program was written by dosemu, modified to - record reads and writes to the ports in the 0x180-0x188 address space, - while running the CMS program TAPE.EXE V2.0.5 supplied with the drive. - - Modified to use an array of addresses and generally cleaned up (made - much shorter) 4 June 94, dosemu isn't that good at writing short code it - would seem :-). Made independent of 0x180, but I doubt it will work - at any other address. - - Modified for distribution with ftape source. 21 June 94, SJL. - - Modifications on 20 October 95, by Daniel Cohen (catman@wpi.edu): - Modified to support different DMA, IRQ, and IO Ports. Borland's - Turbo Debugger in virtual 8086 mode (TD386.EXE with hardware breakpoints - provided by the TDH386.SYS Device Driver) was used on the CMS program - TAPE V4.0.5. I set breakpoints on I/O to ports 0x180-0x187. Note that - CMS's program will not successfully configure the tape drive if you set - breakpoints on IO Reads, but you can set them on IO Writes without problems. - Known problems: - - You can not use DMA Channels 5 or 7. - - Modification on 29 January 96, by Daniel Cohen (catman@wpi.edu): - Modified to only accept IRQs 3 - 7, or 9. Since we can only send a 3 bit - number representing the IRQ to the card, special handling is required when - IRQ 9 is selected. IRQ 2 and 9 are the same, and we should request IRQ 9 - from the kernel while telling the card to use IRQ 2. Thanks to Greg - Crider (gcrider@iclnet.org) for finding and locating this bug, as well as - testing the patch. - - Modification on 11 December 96, by Claus Heine (claus@momo.math.rwth-aachen.de): - Modified a little to use variahle ft_fdc_base, ft_fdc_irq, ft_fdc_dma - instead of preprocessor symbols. Thus we can compile this into the module - or kernel and let the user specify the options as command line arguments. - - * - * $Source: /homes/cvs/ftape-stacked/ftape/lowlevel/fc-10.c,v $ - * $Revision: 1.2 $ - * $Date: 1997/10/05 19:18:04 $ - * - * This file contains code for the CMS FC-10/FC-20 card. - */ - -#include <asm/io.h> -#include <linux/ftape.h> -#include "../lowlevel/ftape-tracing.h" -#include "../lowlevel/fdc-io.h" -#include "../lowlevel/fc-10.h" - -static __u16 inbs_magic[] = { - 0x3, 0x3, 0x0, 0x4, 0x7, 0x2, 0x5, 0x3, 0x1, 0x4, - 0x3, 0x5, 0x2, 0x0, 0x3, 0x7, 0x4, 0x2, - 0x0, 0x1, 0x2, 0x3, 0x4, 0x5, 0x6, 0x7 -}; - -static __u16 fc10_ports[] = { - 0x180, 0x210, 0x2A0, 0x300, 0x330, 0x340, 0x370 -}; - -int fc10_enable(void) -{ - int i; - __u8 cardConfig = 0x00; - __u8 x; - TRACE_FUN(ft_t_flow); - -/* This code will only work if the FC-10 (or FC-20) is set to - * use DMA channels 1, 2, or 3. DMA channels 5 and 7 seem to be - * initialized by the same command as channels 1 and 3, respectively. - */ - if (ft_fdc_dma > 3) { - TRACE_ABORT(0, ft_t_err, -"Error: The FC-10/20 must be set to use DMA channels 1, 2, or 3!"); - } -/* Only allow the FC-10/20 to use IRQ 3-7, or 9. Note that CMS's program - * only accepts IRQ's 2-7, but in linux, IRQ 2 is the same as IRQ 9. - */ - if (ft_fdc_irq < 3 || ft_fdc_irq == 8 || ft_fdc_irq > 9) { - TRACE_ABORT(0, ft_t_err, -"Error: The FC-10/20 must be set to use IRQ levels 3 - 7, or 9!\n" -KERN_INFO "Note: IRQ 9 is the same as IRQ 2"); - } - /* Clear state machine ??? - */ - for (i = 0; i < NR_ITEMS(inbs_magic); i++) { - inb(ft_fdc_base + inbs_magic[i]); - } - outb(0x0, ft_fdc_base); - - x = inb(ft_fdc_base); - if (x == 0x13 || x == 0x93) { - for (i = 1; i < 8; i++) { - if (inb(ft_fdc_base + i) != x) { - TRACE_EXIT 0; - } - } - } else { - TRACE_EXIT 0; - } - - outb(0x8, ft_fdc_base); - - for (i = 0; i < 8; i++) { - if (inb(ft_fdc_base + i) != 0x0) { - TRACE_EXIT 0; - } - } - outb(0x10, ft_fdc_base); - - for (i = 0; i < 8; i++) { - if (inb(ft_fdc_base + i) != 0xff) { - TRACE_EXIT 0; - } - } - - /* Okay, we found a FC-10 card ! ??? - */ - outb(0x0, fdc.ccr); - - /* Clear state machine again ??? - */ - for (i = 0; i < NR_ITEMS(inbs_magic); i++) { - inb(ft_fdc_base + inbs_magic[i]); - } - /* Send io port */ - for (i = 0; i < NR_ITEMS(fc10_ports); i++) - if (ft_fdc_base == fc10_ports[i]) - cardConfig = i + 1; - if (cardConfig == 0) { - TRACE_EXIT 0; /* Invalid I/O Port */ - } - /* and IRQ - If using IRQ 9, tell the FC card it is actually IRQ 2 */ - if (ft_fdc_irq != 9) - cardConfig |= ft_fdc_irq << 3; - else - cardConfig |= 2 << 3; - - /* and finally DMA Channel */ - cardConfig |= ft_fdc_dma << 6; - outb(cardConfig, ft_fdc_base); /* DMA [2 bits]/IRQ [3 bits]/BASE [3 bits] */ - - /* Enable FC-10 ??? - */ - outb(0, fdc.ccr); - outb(0, fdc.dor2); - outb(FDC_DMA_MODE /* 8 */, fdc.dor); - outb(FDC_DMA_MODE /* 8 */, fdc.dor); - outb(1, fdc.dor2); - - /************************************* - * - * cH: why the hell should this be necessary? This is done - * by fdc_reset()!!! - * - *************************************/ - /* Initialize fdc, select drive B: - */ - outb(FDC_DMA_MODE, fdc.dor); /* assert reset, dma & irq enabled */ - /* 0x08 */ - outb(FDC_DMA_MODE|FDC_RESET_NOT, fdc.dor); /* release reset */ - /* 0x08 | 0x04 = 0x0c */ - outb(FDC_DMA_MODE|FDC_RESET_NOT|FDC_MOTOR_1|FTAPE_SEL_B, fdc.dor); - /* 0x08 | 0x04 | 0x20 | 0x01 = 0x2d */ - /* select drive 1 */ /* why not drive 0 ???? */ - TRACE_EXIT (x == 0x93) ? 2 : 1; -} |