diff options
Diffstat (limited to 'drivers/char/mxser_new.h')
| -rw-r--r-- | drivers/char/mxser_new.h | 477 |
1 files changed, 160 insertions, 317 deletions
diff --git a/drivers/char/mxser_new.h b/drivers/char/mxser_new.h index a08f0ecb09b..d42f7766c65 100644 --- a/drivers/char/mxser_new.h +++ b/drivers/char/mxser_new.h @@ -26,18 +26,8 @@ #define RS422_MODE 2 #define RS485_4WIRE_MODE 3 #define OP_MODE_MASK 3 -// above add by Victor Yu. 01-05-2004 - -#define TTY_THRESHOLD_THROTTLE 128 - -#define LO_WATER (TTY_FLIPBUF_SIZE) -#define HI_WATER (TTY_FLIPBUF_SIZE*2*3/4) - -// added by James. 03-11-2004. -#define MOXA_SDS_GETICOUNTER (MOXA + 68) -#define MOXA_SDS_RSTICOUNTER (MOXA + 69) -// (above) added by James. +#define MOXA_SDS_RSTICOUNTER (MOXA + 69) #define MOXA_ASPP_OQUEUE (MOXA + 70) #define MOXA_ASPP_SETBAUD (MOXA + 71) #define MOXA_ASPP_GETBAUD (MOXA + 72) @@ -45,7 +35,8 @@ #define MOXA_ASPP_LSTATUS (MOXA + 74) #define MOXA_ASPP_MON_EXT (MOXA + 75) #define MOXA_SET_BAUD_METHOD (MOXA + 76) - +#define MOXA_SET_SPECIAL_BAUD_RATE (MOXA + 77) +#define MOXA_GET_SPECIAL_BAUD_RATE (MOXA + 78) /* --------------------------------------------------- */ @@ -55,51 +46,46 @@ #define NPPI_NOTIFY_SW_OVERRUN 0x08 #define NPPI_NOTIFY_BREAK 0x10 -#define NPPI_NOTIFY_CTSHOLD 0x01 // Tx hold by CTS low -#define NPPI_NOTIFY_DSRHOLD 0x02 // Tx hold by DSR low -#define NPPI_NOTIFY_XOFFHOLD 0x08 // Tx hold by Xoff received -#define NPPI_NOTIFY_XOFFXENT 0x10 // Xoff Sent - -//CheckIsMoxaMust return value -#define MOXA_OTHER_UART 0x00 -#define MOXA_MUST_MU150_HWID 0x01 -#define MOXA_MUST_MU860_HWID 0x02 - -// follow just for Moxa Must chip define. -// -// when LCR register (offset 0x03) write following value, -// the Must chip will enter enchance mode. And write value -// on EFR (offset 0x02) bit 6,7 to change bank. +#define NPPI_NOTIFY_CTSHOLD 0x01 /* Tx hold by CTS low */ +#define NPPI_NOTIFY_DSRHOLD 0x02 /* Tx hold by DSR low */ +#define NPPI_NOTIFY_XOFFHOLD 0x08 /* Tx hold by Xoff received */ +#define NPPI_NOTIFY_XOFFXENT 0x10 /* Xoff Sent */ + +/* follow just for Moxa Must chip define. */ +/* */ +/* when LCR register (offset 0x03) write following value, */ +/* the Must chip will enter enchance mode. And write value */ +/* on EFR (offset 0x02) bit 6,7 to change bank. */ #define MOXA_MUST_ENTER_ENCHANCE 0xBF -// when enhance mode enable, access on general bank register +/* when enhance mode enable, access on general bank register */ #define MOXA_MUST_GDL_REGISTER 0x07 #define MOXA_MUST_GDL_MASK 0x7F #define MOXA_MUST_GDL_HAS_BAD_DATA 0x80 -#define MOXA_MUST_LSR_RERR 0x80 // error in receive FIFO -// enchance register bank select and enchance mode setting register -// when LCR register equal to 0xBF +#define MOXA_MUST_LSR_RERR 0x80 /* error in receive FIFO */ +/* enchance register bank select and enchance mode setting register */ +/* when LCR register equal to 0xBF */ #define MOXA_MUST_EFR_REGISTER 0x02 -// enchance mode enable +/* enchance mode enable */ #define MOXA_MUST_EFR_EFRB_ENABLE 0x10 -// enchance reister bank set 0, 1, 2 +/* enchance reister bank set 0, 1, 2 */ #define MOXA_MUST_EFR_BANK0 0x00 #define MOXA_MUST_EFR_BANK1 0x40 #define MOXA_MUST_EFR_BANK2 0x80 #define MOXA_MUST_EFR_BANK3 0xC0 #define MOXA_MUST_EFR_BANK_MASK 0xC0 -// set XON1 value register, when LCR=0xBF and change to bank0 +/* set XON1 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XON1_REGISTER 0x04 -// set XON2 value register, when LCR=0xBF and change to bank0 +/* set XON2 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XON2_REGISTER 0x05 -// set XOFF1 value register, when LCR=0xBF and change to bank0 +/* set XOFF1 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XOFF1_REGISTER 0x06 -// set XOFF2 value register, when LCR=0xBF and change to bank0 +/* set XOFF2 value register, when LCR=0xBF and change to bank0 */ #define MOXA_MUST_XOFF2_REGISTER 0x07 #define MOXA_MUST_RBRTL_REGISTER 0x04 @@ -111,32 +97,32 @@ #define MOXA_MUST_ECR_REGISTER 0x06 #define MOXA_MUST_CSR_REGISTER 0x07 -// good data mode enable +/* good data mode enable */ #define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20 -// only good data put into RxFIFO +/* only good data put into RxFIFO */ #define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10 -// enable CTS interrupt +/* enable CTS interrupt */ #define MOXA_MUST_IER_ECTSI 0x80 -// enable RTS interrupt +/* enable RTS interrupt */ #define MOXA_MUST_IER_ERTSI 0x40 -// enable Xon/Xoff interrupt +/* enable Xon/Xoff interrupt */ #define MOXA_MUST_IER_XINT 0x20 -// enable GDA interrupt +/* enable GDA interrupt */ #define MOXA_MUST_IER_EGDAI 0x10 #define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI) -// GDA interrupt pending +/* GDA interrupt pending */ #define MOXA_MUST_IIR_GDA 0x1C #define MOXA_MUST_IIR_RDA 0x04 #define MOXA_MUST_IIR_RTO 0x0C #define MOXA_MUST_IIR_LSR 0x06 -// recieved Xon/Xoff or specical interrupt pending +/* recieved Xon/Xoff or specical interrupt pending */ #define MOXA_MUST_IIR_XSC 0x10 -// RTS/CTS change state interrupt pending +/* RTS/CTS change state interrupt pending */ #define MOXA_MUST_IIR_RTSCTS 0x20 #define MOXA_MUST_IIR_MASK 0x3E @@ -144,307 +130,164 @@ #define MOXA_MUST_MCR_XON_ANY 0x80 #define MOXA_MUST_MCR_TX_XON 0x08 - -// software flow control on chip mask value +/* software flow control on chip mask value */ #define MOXA_MUST_EFR_SF_MASK 0x0F -// send Xon1/Xoff1 +/* send Xon1/Xoff1 */ #define MOXA_MUST_EFR_SF_TX1 0x08 -// send Xon2/Xoff2 +/* send Xon2/Xoff2 */ #define MOXA_MUST_EFR_SF_TX2 0x04 -// send Xon1,Xon2/Xoff1,Xoff2 +/* send Xon1,Xon2/Xoff1,Xoff2 */ #define MOXA_MUST_EFR_SF_TX12 0x0C -// don't send Xon/Xoff +/* don't send Xon/Xoff */ #define MOXA_MUST_EFR_SF_TX_NO 0x00 -// Tx software flow control mask +/* Tx software flow control mask */ #define MOXA_MUST_EFR_SF_TX_MASK 0x0C -// don't receive Xon/Xoff +/* don't receive Xon/Xoff */ #define MOXA_MUST_EFR_SF_RX_NO 0x00 -// receive Xon1/Xoff1 +/* receive Xon1/Xoff1 */ #define MOXA_MUST_EFR_SF_RX1 0x02 -// receive Xon2/Xoff2 +/* receive Xon2/Xoff2 */ #define MOXA_MUST_EFR_SF_RX2 0x01 -// receive Xon1,Xon2/Xoff1,Xoff2 +/* receive Xon1,Xon2/Xoff1,Xoff2 */ #define MOXA_MUST_EFR_SF_RX12 0x03 -// Rx software flow control mask +/* Rx software flow control mask */ #define MOXA_MUST_EFR_SF_RX_MASK 0x03 -//#define MOXA_MUST_MIN_XOFFLIMIT 66 -//#define MOXA_MUST_MIN_XONLIMIT 20 -//#define ID1_RX_TRIG 120 - - -#define CHECK_MOXA_MUST_XOFFLIMIT(info) { \ - if ( (info)->IsMoxaMustChipFlag && \ - (info)->HandFlow.XoffLimit < MOXA_MUST_MIN_XOFFLIMIT ) { \ - (info)->HandFlow.XoffLimit = MOXA_MUST_MIN_XOFFLIMIT; \ - (info)->HandFlow.XonLimit = MOXA_MUST_MIN_XONLIMIT; \ - } \ -} - -#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ +#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK0; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ outb((u8)(Value), (baseio)+MOXA_MUST_XON1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) -#define SET_MOXA_MUST_XON2_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ +#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XON2_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK0; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ outb((u8)(Value), (baseio)+MOXA_MUST_XOFF1_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) -#define SET_MOXA_MUST_XOFF2_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK0; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_XOFF2_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_RBRTL_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_RBRTL_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_RBRTH_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_RBRTH_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_RBRTI_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_RBRTI_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_THRTL_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb((u8)(Value), (baseio)+MOXA_MUST_THRTL_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -//#define MOXA_MUST_RBRL_VALUE 4 -#define SET_MOXA_MUST_FIFO_VALUE(info) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((info)->ioaddr+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (info)->ioaddr+UART_LCR); \ +#define SET_MOXA_MUST_FIFO_VALUE(info) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((info)->ioaddr+UART_LCR); \ + outb(MOXA_MUST_ENTER_ENCHANCE, (info)->ioaddr+UART_LCR);\ __efr = inb((info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK1; \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK1; \ outb(__efr, (info)->ioaddr+MOXA_MUST_EFR_REGISTER); \ - outb((u8)((info)->rx_high_water), (info)->ioaddr+MOXA_MUST_RBRTH_REGISTER); \ - outb((u8)((info)->rx_trigger), (info)->ioaddr+MOXA_MUST_RBRTI_REGISTER); \ - outb((u8)((info)->rx_low_water), (info)->ioaddr+MOXA_MUST_RBRTL_REGISTER); \ - outb(__oldlcr, (info)->ioaddr+UART_LCR); \ -} - - - -#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + outb((u8)((info)->rx_high_water), (info)->ioaddr+ \ + MOXA_MUST_RBRTH_REGISTER); \ + outb((u8)((info)->rx_trigger), (info)->ioaddr+ \ + MOXA_MUST_RBRTI_REGISTER); \ + outb((u8)((info)->rx_low_water), (info)->ioaddr+ \ + MOXA_MUST_RBRTL_REGISTER); \ + outb(__oldlcr, (info)->ioaddr+UART_LCR); \ +} while (0) + +#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK2; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ outb((u8)(Value), (baseio)+MOXA_MUST_ENUM_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) -#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ - __efr |= MOXA_MUST_EFR_BANK2; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_JUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ +#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - __efr |= MOXA_MUST_EFR_SF_TX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_BANK_MASK; \ + __efr |= MOXA_MUST_EFR_BANK2; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_TX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_MASK; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define SET_MOXA_MUST_JUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ + __efr |= MOXA_MUST_EFR_SF_TX1; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - __efr |= MOXA_MUST_EFR_SF_RX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - __efr |= MOXA_MUST_EFR_SF_RX1; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ + __efr |= MOXA_MUST_EFR_SF_RX1; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) + +#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \ + u8 __oldlcr, __efr; \ + __oldlcr = inb((baseio)+UART_LCR); \ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_TX_RX_SOFTWARE_FLOW_CONTROL(baseio) { \ - u8 __oldlcr, __efr; \ - __oldlcr = inb((baseio)+UART_LCR); \ - outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \ - __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ - __efr &= ~MOXA_MUST_EFR_SF_MASK; \ - __efr |= (MOXA_MUST_EFR_SF_RX1|MOXA_MUST_EFR_SF_TX1); \ - outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ - outb(__oldlcr, (baseio)+UART_LCR); \ -} - -#define ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \ - u8 __oldmcr; \ - __oldmcr = inb((baseio)+UART_MCR); \ - __oldmcr |= MOXA_MUST_MCR_XON_ANY; \ - outb(__oldmcr, (baseio)+UART_MCR); \ -} - -#define DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \ - u8 __oldmcr; \ - __oldmcr = inb((baseio)+UART_MCR); \ - __oldmcr &= ~MOXA_MUST_MCR_XON_ANY; \ - outb(__oldmcr, (baseio)+UART_MCR); \ -} - -#define READ_MOXA_MUST_GDL(baseio) inb((baseio)+MOXA_MUST_GDL_REGISTER) - - -#ifndef INIT_WORK -#define INIT_WORK(_work, _func, _data){ \ - _data->tqueue.routine = _func;\ - _data->tqueue.data = _data;\ - } -#endif + __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \ + __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \ + outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \ + outb(__oldlcr, (baseio)+UART_LCR); \ +} while (0) #endif |