diff options
Diffstat (limited to 'drivers/char/serial167.c')
| -rw-r--r-- | drivers/char/serial167.c | 223 |
1 files changed, 1 insertions, 222 deletions
diff --git a/drivers/char/serial167.c b/drivers/char/serial167.c index 78a62ebe75c..ecbe479c7d6 100644 --- a/drivers/char/serial167.c +++ b/drivers/char/serial167.c @@ -176,23 +176,6 @@ static void config_setup(struct cyclades_port *); static void show_status(int); #endif -#ifdef CONFIG_REMOTE_DEBUG -static void debug_setup(void); -void queueDebugChar(int c); -int getDebugChar(void); - -#define DEBUG_PORT 1 -#define DEBUG_LEN 256 - -typedef struct { - int in; - int out; - unsigned char buf[DEBUG_LEN]; -} debugq; - -debugq debugiq; -#endif - /* * I have my own version of udelay(), as it is needed when initialising * the chip, before the delay loop has been calibrated. Should probably @@ -515,11 +498,6 @@ static irqreturn_t cd2401_tx_interrupt(int irq, void *dev_id) /* determine the channel and change to that context */ channel = (u_short) (base_addr[CyLICR] >> 2); -#ifdef CONFIG_REMOTE_DEBUG - if (channel == DEBUG_PORT) { - panic("TxInt on debug port!!!"); - } -#endif /* validate the port number (as configured and open) */ if ((channel < 0) || (NR_PORTS <= channel)) { base_addr[CyIER] &= ~(CyTxMpty | CyTxRdy); @@ -634,14 +612,6 @@ static irqreturn_t cd2401_rx_interrupt(int irq, void *dev_id) info->last_active = jiffies; save_cnt = char_count = base_addr[CyRFOC]; -#ifdef CONFIG_REMOTE_DEBUG - if (channel == DEBUG_PORT) { - while (char_count--) { - data = base_addr[CyRDR]; - queueDebugChar(data); - } - } else -#endif /* if there is nowhere to put the data, discard it */ if (info->tty == 0) { while (char_count--) { @@ -2195,9 +2165,7 @@ static int __init serial167_init(void) port_num++; info++; } -#ifdef CONFIG_REMOTE_DEBUG - debug_setup(); -#endif + ret = request_irq(MVME167_IRQ_SER_ERR, cd2401_rxerr_interrupt, 0, "cd2401_errors", cd2401_rxerr_interrupt); if (ret) { @@ -2518,193 +2486,4 @@ static int __init serial167_console_init(void) console_initcall(serial167_console_init); -#ifdef CONFIG_REMOTE_DEBUG -void putDebugChar(int c) -{ - volatile unsigned char *base_addr = (u_char *) BASE_ADDR; - unsigned long flags; - volatile u_char sink; - u_char ier; - int port; - - local_irq_save(flags); - - /* Ensure transmitter is enabled! */ - - port = DEBUG_PORT; - base_addr[CyCAR] = (u_char) port; - while (base_addr[CyCCR]) - ; - base_addr[CyCCR] = CyENB_XMTR; - - ier = base_addr[CyIER]; - base_addr[CyIER] = CyTxMpty; - - while (1) { - if (pcc2chip[PccSCCTICR] & 0x20) { - /* We have a Tx int. Acknowledge it */ - sink = pcc2chip[PccTPIACKR]; - if ((base_addr[CyLICR] >> 2) == port) { - base_addr[CyTDR] = c; - base_addr[CyTEOIR] = 0; - break; - } else - base_addr[CyTEOIR] = CyNOTRANS; - } - } - - base_addr[CyIER] = ier; - - local_irq_restore(flags); -} - -int getDebugChar() -{ - volatile unsigned char *base_addr = (u_char *) BASE_ADDR; - unsigned long flags; - volatile u_char sink; - u_char ier; - int port; - int i, c; - - i = debugiq.out; - if (i != debugiq.in) { - c = debugiq.buf[i]; - if (++i == DEBUG_LEN) - i = 0; - debugiq.out = i; - return c; - } - /* OK, nothing in queue, wait in poll loop */ - - local_irq_save(flags); - - /* Ensure receiver is enabled! */ - - port = DEBUG_PORT; - base_addr[CyCAR] = (u_char) port; -#if 0 - while (base_addr[CyCCR]) - ; - base_addr[CyCCR] = CyENB_RCVR; -#endif - ier = base_addr[CyIER]; - base_addr[CyIER] = CyRxData; - - while (1) { - if (pcc2chip[PccSCCRICR] & 0x20) { - /* We have a Rx int. Acknowledge it */ - sink = pcc2chip[PccRPIACKR]; - if ((base_addr[CyLICR] >> 2) == port) { - int cnt = base_addr[CyRFOC]; - while (cnt-- > 0) { - c = base_addr[CyRDR]; - if (c == 0) - printk - ("!! debug char is null (cnt=%d) !!", - cnt); - else - queueDebugChar(c); - } - base_addr[CyREOIR] = 0; - i = debugiq.out; - if (i == debugiq.in) - panic("Debug input queue empty!"); - c = debugiq.buf[i]; - if (++i == DEBUG_LEN) - i = 0; - debugiq.out = i; - break; - } else - base_addr[CyREOIR] = CyNOTRANS; - } - } - - base_addr[CyIER] = ier; - - local_irq_restore(flags); - - return (c); -} - -void queueDebugChar(int c) -{ - int i; - - i = debugiq.in; - debugiq.buf[i] = c; - if (++i == DEBUG_LEN) - i = 0; - if (i != debugiq.out) - debugiq.in = i; -} - -static void debug_setup() -{ - unsigned long flags; - volatile unsigned char *base_addr = (u_char *) BASE_ADDR; - int i, cflag; - - cflag = B19200; - - local_irq_save(flags); - - for (i = 0; i < 4; i++) { - base_addr[CyCAR] = i; - base_addr[CyLICR] = i << 2; - } - - debugiq.in = debugiq.out = 0; - - base_addr[CyCAR] = DEBUG_PORT; - - /* baud rate */ - i = cflag & CBAUD; - - base_addr[CyIER] = 0; - - base_addr[CyCMR] = CyASYNC; - base_addr[CyLICR] = DEBUG_PORT << 2; - base_addr[CyLIVR] = 0x5c; - - /* tx and rx baud rate */ - - base_addr[CyTCOR] = baud_co[i]; - base_addr[CyTBPR] = baud_bpr[i]; - base_addr[CyRCOR] = baud_co[i] >> 5; - base_addr[CyRBPR] = baud_bpr[i]; - - /* set line characteristics according configuration */ - - base_addr[CySCHR1] = 0; - base_addr[CySCHR2] = 0; - base_addr[CySCRL] = 0; - base_addr[CySCRH] = 0; - base_addr[CyCOR1] = Cy_8_BITS | CyPARITY_NONE; - base_addr[CyCOR2] = 0; - base_addr[CyCOR3] = Cy_1_STOP; - base_addr[CyCOR4] = baud_cor4[i]; - base_addr[CyCOR5] = 0; - base_addr[CyCOR6] = 0; - base_addr[CyCOR7] = 0; - - write_cy_cmd(base_addr, CyINIT_CHAN); - write_cy_cmd(base_addr, CyENB_RCVR); - - base_addr[CyCAR] = DEBUG_PORT; /* !!! Is this needed? */ - - base_addr[CyRTPRL] = 2; - base_addr[CyRTPRH] = 0; - - base_addr[CyMSVR1] = CyRTS; - base_addr[CyMSVR2] = CyDTR; - - base_addr[CyIER] = CyRxData; - - local_irq_restore(flags); - -} /* debug_setup */ - -#endif - MODULE_LICENSE("GPL"); |