summaryrefslogtreecommitdiffstats
path: root/drivers/gpio/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/gpio/Kconfig')
-rw-r--r--drivers/gpio/Kconfig57
1 files changed, 56 insertions, 1 deletions
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 1f1d88ae68d..fee678f74a1 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -65,8 +65,17 @@ config GPIO_SYSFS
# put expanders in the right section, in alphabetical order
+config GPIO_MAX730X
+ tristate
+
comment "Memory mapped GPIO expanders:"
+config GPIO_IT8761E
+ tristate "IT8761E GPIO support"
+ depends on GPIOLIB
+ help
+ Say yes here to support GPIO functionality of IT8761E super I/O chip.
+
config GPIO_PL061
bool "PrimeCell PL061 GPIO support"
depends on ARM_AMBA
@@ -85,8 +94,32 @@ config GPIO_VR41XX
help
Say yes here to support the NEC VR4100 series General-purpose I/O Uint
+config GPIO_SCH
+ tristate "Intel SCH GPIO"
+ depends on GPIOLIB && PCI
+ select MFD_CORE
+ select LPC_SCH
+ help
+ Say yes here to support GPIO interface on Intel Poulsbo SCH.
+ The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
+ powered by the core power rail and are turned off during sleep
+ modes (S3 and higher). The remaining four GPIOs are powered by
+ the Intel SCH suspend power supply. These GPIOs remain
+ active during S3. The suspend powered GPIOs can be used to wake the
+ system from the Suspend-to-RAM state.
+
+ This driver can also be built as a module. If so, the module
+ will be called sch-gpio.
+
comment "I2C GPIO expanders:"
+config GPIO_MAX7300
+ tristate "Maxim MAX7300 GPIO expander"
+ depends on I2C
+ select GPIO_MAX730X
+ help
+ GPIO driver for Maxim MAX7301 I2C-based GPIO expander.
+
config GPIO_MAX732X
tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
depends on I2C
@@ -124,6 +157,13 @@ config GPIO_PCA953X
This driver can also be built as a module. If so, the module
will be called pca953x.
+config GPIO_PCA953X_IRQ
+ bool "Interrupt controller support for PCA953x"
+ depends on GPIO_PCA953X=y
+ help
+ Say yes here to enable the pca953x to be used as an interrupt
+ controller. It requires the driver to be built in the kernel.
+
config GPIO_PCF857X
tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
depends on I2C
@@ -162,6 +202,20 @@ config GPIO_WM831X
Say yes here to access the GPIO signals of WM831x power management
chips from Wolfson Microelectronics.
+config GPIO_WM8350
+ tristate "WM8350 GPIOs"
+ depends on MFD_WM8350
+ help
+ Say yes here to access the GPIO signals of WM8350 power management
+ chips from Wolfson Microelectronics.
+
+config GPIO_WM8994
+ tristate "WM8994 GPIOs"
+ depends on MFD_WM8994
+ help
+ Say yes here to access the GPIO signals of WM8994 audio hub
+ CODECs from Wolfson Microelectronics.
+
config GPIO_ADP5520
tristate "GPIO Support for ADP5520 PMIC"
depends on PMIC_ADP5520
@@ -226,8 +280,9 @@ comment "SPI GPIO expanders:"
config GPIO_MAX7301
tristate "Maxim MAX7301 GPIO expander"
depends on SPI_MASTER
+ select GPIO_MAX730X
help
- gpio driver for Maxim MAX7301 SPI GPIO expander.
+ GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
config GPIO_MCP23S08
tristate "Microchip MCP23S08 I/O expander"