diff options
Diffstat (limited to 'drivers/gpio')
| -rw-r--r-- | drivers/gpio/Kconfig | 16 | ||||
| -rw-r--r-- | drivers/gpio/Makefile | 6 | ||||
| -rw-r--r-- | drivers/gpio/gpio-exynos4.c | 385 | ||||
| -rw-r--r-- | drivers/gpio/gpio-plat-samsung.c | 205 | ||||
| -rw-r--r-- | drivers/gpio/gpio-s5pc100.c | 354 | ||||
| -rw-r--r-- | drivers/gpio/gpio-s5pv210.c | 287 | ||||
| -rw-r--r-- | drivers/gpio/gpio-samsung.c | 2688 |
7 files changed, 2689 insertions, 1252 deletions
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 8b3c745b1b0..74603ca06e3 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -95,10 +95,6 @@ config GPIO_EP93XX depends on ARCH_EP93XX select GPIO_GENERIC -config GPIO_EXYNOS4 - def_bool y - depends on CPU_EXYNOS4210 - config GPIO_MPC5200 def_bool y depends on PPC_MPC52xx @@ -131,18 +127,6 @@ config GPIO_MXS select GPIO_GENERIC select GENERIC_IRQ_CHIP -config GPIO_PLAT_SAMSUNG - def_bool y - depends on SAMSUNG_GPIOLIB_4BIT - -config GPIO_S5PC100 - def_bool y - depends on CPU_S5PC100 - -config GPIO_S5PV210 - def_bool y - depends on CPU_S5PV210 - config GPIO_PL061 bool "PrimeCell PL061 GPIO support" depends on ARM_AMBA diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 19c5d27b6d2..4a9ad2f99ad 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -16,7 +16,6 @@ obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o obj-$(CONFIG_ARCH_DAVINCI) += gpio-davinci.o obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o -obj-$(CONFIG_GPIO_EXYNOS4) += gpio-exynos4.o obj-$(CONFIG_GPIO_IT8761E) += gpio-it8761e.o obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o obj-$(CONFIG_MACH_KS8695) += gpio-ks8695.o @@ -42,10 +41,7 @@ obj-$(CONFIG_GPIO_PCH) += gpio-pch.o obj-$(CONFIG_GPIO_PL061) += gpio-pl061.o obj-$(CONFIG_PLAT_PXA) += gpio-pxa.o obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o - -obj-$(CONFIG_GPIO_PLAT_SAMSUNG) += gpio-plat-samsung.o -obj-$(CONFIG_GPIO_S5PC100) += gpio-s5pc100.o -obj-$(CONFIG_GPIO_S5PV210) += gpio-s5pv210.o +obj-$(CONFIG_PLAT_SAMSUNG) += gpio-samsung.o obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o obj-$(CONFIG_GPIO_SCH) += gpio-sch.o obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o diff --git a/drivers/gpio/gpio-exynos4.c b/drivers/gpio/gpio-exynos4.c deleted file mode 100644 index d24b337cf1a..00000000000 --- a/drivers/gpio/gpio-exynos4.c +++ /dev/null @@ -1,385 +0,0 @@ -/* - * EXYNOS4 - GPIOlib support - * - * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd. - * http://www.samsung.com - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include <linux/kernel.h> -#include <linux/irq.h> -#include <linux/io.h> -#include <linux/gpio.h> - -#include <mach/map.h> - -#include <plat/gpio-core.h> -#include <plat/gpio-cfg.h> -#include <plat/gpio-cfg-helpers.h> - -int s3c_gpio_setpull_exynos4(struct s3c_gpio_chip *chip, - unsigned int off, s3c_gpio_pull_t pull) -{ - if (pull == S3C_GPIO_PULL_UP) - pull = 3; - - return s3c_gpio_setpull_updown(chip, off, pull); -} - -s3c_gpio_pull_t s3c_gpio_getpull_exynos4(struct s3c_gpio_chip *chip, - unsigned int off) -{ - s3c_gpio_pull_t pull; - - pull = s3c_gpio_getpull_updown(chip, off); - if (pull == 3) - pull = S3C_GPIO_PULL_UP; - - return pull; -} - -static struct s3c_gpio_cfg gpio_cfg = { - .set_config = s3c_gpio_setcfg_s3c64xx_4bit, - .set_pull = s3c_gpio_setpull_exynos4, - .get_pull = s3c_gpio_getpull_exynos4, -}; - -static struct s3c_gpio_cfg gpio_cfg_noint = { - .set_config = s3c_gpio_setcfg_s3c64xx_4bit, - .set_pull = s3c_gpio_setpull_exynos4, - .get_pull = s3c_gpio_getpull_exynos4, -}; - -/* - * Following are the gpio banks in v310. - * - * The 'config' member when left to NULL, is initialized to the default - * structure gpio_cfg in the init function below. - * - * The 'base' member is also initialized in the init function below. - * Note: The initialization of 'base' member of s3c_gpio_chip structure - * uses the above macro and depends on the banks being listed in order here. - */ -static struct s3c_gpio_chip exynos4_gpio_part1_4bit[] = { - { - .chip = { - .base = EXYNOS4_GPA0(0), - .ngpio = EXYNOS4_GPIO_A0_NR, - .label = "GPA0", - }, - }, { - .chip = { - .base = EXYNOS4_GPA1(0), - .ngpio = EXYNOS4_GPIO_A1_NR, - .label = "GPA1", - }, - }, { - .chip = { - .base = EXYNOS4_GPB(0), - .ngpio = EXYNOS4_GPIO_B_NR, - .label = "GPB", - }, - }, { - .chip = { - .base = EXYNOS4_GPC0(0), - .ngpio = EXYNOS4_GPIO_C0_NR, - .label = "GPC0", - }, - }, { - .chip = { - .base = EXYNOS4_GPC1(0), - .ngpio = EXYNOS4_GPIO_C1_NR, - .label = "GPC1", - }, - }, { - .chip = { - .base = EXYNOS4_GPD0(0), - .ngpio = EXYNOS4_GPIO_D0_NR, - .label = "GPD0", - }, - }, { - .chip = { - .base = EXYNOS4_GPD1(0), - .ngpio = EXYNOS4_GPIO_D1_NR, - .label = "GPD1", - }, - }, { - .chip = { - .base = EXYNOS4_GPE0(0), - .ngpio = EXYNOS4_GPIO_E0_NR, - .label = "GPE0", - }, - }, { - .chip = { - .base = EXYNOS4_GPE1(0), - .ngpio = EXYNOS4_GPIO_E1_NR, - .label = "GPE1", - }, - }, { - .chip = { - .base = EXYNOS4_GPE2(0), - .ngpio = EXYNOS4_GPIO_E2_NR, - .label = "GPE2", - }, - }, { - .chip = { - .base = EXYNOS4_GPE3(0), - .ngpio = EXYNOS4_GPIO_E3_NR, - .label = "GPE3", - }, - }, { - .chip = { - .base = EXYNOS4_GPE4(0), - .ngpio = EXYNOS4_GPIO_E4_NR, - .label = "GPE4", - }, - }, { - .chip = { - .base = EXYNOS4_GPF0(0), - .ngpio = EXYNOS4_GPIO_F0_NR, - .label = "GPF0", - }, - }, { - .chip = { - .base = EXYNOS4_GPF1(0), - .ngpio = EXYNOS4_GPIO_F1_NR, - .label = "GPF1", - }, - }, { - .chip = { - .base = EXYNOS4_GPF2(0), - .ngpio = EXYNOS4_GPIO_F2_NR, - .label = "GPF2", - }, - }, { - .chip = { - .base = EXYNOS4_GPF3(0), - .ngpio = EXYNOS4_GPIO_F3_NR, - .label = "GPF3", - }, - }, -}; - -static struct s3c_gpio_chip exynos4_gpio_part2_4bit[] = { - { - .chip = { - .base = EXYNOS4_GPJ0(0), - .ngpio = EXYNOS4_GPIO_J0_NR, - .label = "GPJ0", - }, - }, { - .chip = { - .base = EXYNOS4_GPJ1(0), - .ngpio = EXYNOS4_GPIO_J1_NR, - .label = "GPJ1", - }, - }, { - .chip = { - .base = EXYNOS4_GPK0(0), - .ngpio = EXYNOS4_GPIO_K0_NR, - .label = "GPK0", - }, - }, { - .chip = { - .base = EXYNOS4_GPK1(0), - .ngpio = EXYNOS4_GPIO_K1_NR, - .label = "GPK1", - }, - }, { - .chip = { - .base = EXYNOS4_GPK2(0), - .ngpio = EXYNOS4_GPIO_K2_NR, - .label = "GPK2", - }, - }, { - .chip = { - .base = EXYNOS4_GPK3(0), - .ngpio = EXYNOS4_GPIO_K3_NR, - .label = "GPK3", - }, - }, { - .chip = { - .base = EXYNOS4_GPL0(0), - .ngpio = EXYNOS4_GPIO_L0_NR, - .label = "GPL0", - }, - }, { - .chip = { - .base = EXYNOS4_GPL1(0), - .ngpio = EXYNOS4_GPIO_L1_NR, - .label = "GPL1", - }, - }, { - .chip = { - .base = EXYNOS4_GPL2(0), - .ngpio = EXYNOS4_GPIO_L2_NR, - .label = "GPL2", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = EXYNOS4_GPY0(0), - .ngpio = EXYNOS4_GPIO_Y0_NR, - .label = "GPY0", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = EXYNOS4_GPY1(0), - .ngpio = EXYNOS4_GPIO_Y1_NR, - .label = "GPY1", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = EXYNOS4_GPY2(0), - .ngpio = EXYNOS4_GPIO_Y2_NR, - .label = "GPY2", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = EXYNOS4_GPY3(0), - .ngpio = EXYNOS4_GPIO_Y3_NR, - .label = "GPY3", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = EXYNOS4_GPY4(0), - .ngpio = EXYNOS4_GPIO_Y4_NR, - .label = "GPY4", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = EXYNOS4_GPY5(0), - .ngpio = EXYNOS4_GPIO_Y5_NR, - .label = "GPY5", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = EXYNOS4_GPY6(0), - .ngpio = EXYNOS4_GPIO_Y6_NR, - .label = "GPY6", - }, - }, { - .base = (S5P_VA_GPIO2 + 0xC00), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(0), - .chip = { - .base = EXYNOS4_GPX0(0), - .ngpio = EXYNOS4_GPIO_X0_NR, - .label = "GPX0", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO2 + 0xC20), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(8), - .chip = { - .base = EXYNOS4_GPX1(0), - .ngpio = EXYNOS4_GPIO_X1_NR, - .label = "GPX1", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO2 + 0xC40), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(16), - .chip = { - .base = EXYNOS4_GPX2(0), - .ngpio = EXYNOS4_GPIO_X2_NR, - .label = "GPX2", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO2 + 0xC60), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(24), - .chip = { - .base = EXYNOS4_GPX3(0), - .ngpio = EXYNOS4_GPIO_X3_NR, - .label = "GPX3", - .to_irq = samsung_gpiolib_to_irq, - }, - }, -}; - -static struct s3c_gpio_chip exynos4_gpio_part3_4bit[] = { - { - .chip = { - .base = EXYNOS4_GPZ(0), - .ngpio = EXYNOS4_GPIO_Z_NR, - .label = "GPZ", - }, - }, -}; - -static __init int exynos4_gpiolib_init(void) -{ - struct s3c_gpio_chip *chip; - int i; - int group = 0; - int nr_chips; - - /* GPIO part 1 */ - - chip = exynos4_gpio_part1_4bit; - nr_chips = ARRAY_SIZE(exynos4_gpio_part1_4bit); - - for (i = 0; i < nr_chips; i++, chip++) { - if (chip->config == NULL) { - chip->config = &gpio_cfg; - /* Assign the GPIO interrupt group */ - chip->group = group++; - } - if (chip->base == NULL) - chip->base = S5P_VA_GPIO1 + (i) * 0x20; - } - - samsung_gpiolib_add_4bit_chips(exynos4_gpio_part1_4bit, nr_chips); - - /* GPIO part 2 */ - - chip = exynos4_gpio_part2_4bit; - nr_chips = ARRAY_SIZE(exynos4_gpio_part2_4bit); - - for (i = 0; i < nr_chips; i++, chip++) { - if (chip->config == NULL) { - chip->config = &gpio_cfg; - /* Assign the GPIO interrupt group */ - chip->group = group++; - } - if (chip->base == NULL) - chip->base = S5P_VA_GPIO2 + (i) * 0x20; - } - - samsung_gpiolib_add_4bit_chips(exynos4_gpio_part2_4bit, nr_chips); - - /* GPIO part 3 */ - - chip = exynos4_gpio_part3_4bit; - nr_chips = ARRAY_SIZE(exynos4_gpio_part3_4bit); - - for (i = 0; i < nr_chips; i++, chip++) { - if (chip->config == NULL) { - chip->config = &gpio_cfg; - /* Assign the GPIO interrupt group */ - chip->group = group++; - } - if (chip->base == NULL) - chip->base = S5P_VA_GPIO3 + (i) * 0x20; - } - - samsung_gpiolib_add_4bit_chips(exynos4_gpio_part3_4bit, nr_chips); - s5p_register_gpioint_bank(IRQ_GPIO_XA, 0, IRQ_GPIO1_NR_GROUPS); - s5p_register_gpioint_bank(IRQ_GPIO_XB, IRQ_GPIO1_NR_GROUPS, IRQ_GPIO2_NR_GROUPS); - - return 0; -} -core_initcall(exynos4_gpiolib_init); diff --git a/drivers/gpio/gpio-plat-samsung.c b/drivers/gpio/gpio-plat-samsung.c deleted file mode 100644 index ef67f1952a7..00000000000 --- a/drivers/gpio/gpio-plat-samsung.c +++ /dev/null @@ -1,205 +0,0 @@ -/* - * Copyright 2008 Openmoko, Inc. - * Copyright 2008 Simtec Electronics - * Ben Dooks <ben@simtec.co.uk> - * http://armlinux.simtec.co.uk/ - * - * Copyright (c) 2009 Samsung Electronics Co., Ltd. - * http://www.samsung.com/ - * - * SAMSUNG - GPIOlib support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/irq.h> -#include <linux/io.h> -#include <linux/gpio.h> -#include <plat/gpio-core.h> -#include <plat/gpio-cfg.h> -#include <plat/gpio-cfg-helpers.h> - -#ifndef DEBUG_GPIO -#define gpio_dbg(x...) do { } while (0) -#else -#define gpio_dbg(x...) printk(KERN_DEBUG x) -#endif - -/* The samsung_gpiolib_4bit routines are to control the gpio banks where - * the gpio configuration register (GPxCON) has 4 bits per GPIO, as the - * following example: - * - * base + 0x00: Control register, 4 bits per gpio - * gpio n: 4 bits starting at (4*n) - * 0000 = input, 0001 = output, others mean special-function - * base + 0x04: Data register, 1 bit per gpio - * bit n: data bit n - * - * Note, since the data register is one bit per gpio and is at base + 0x4 - * we can use s3c_gpiolib_get and s3c_gpiolib_set to change the state of - * the output. -*/ - -static int samsung_gpiolib_4bit_input(struct gpio_chip *chip, - unsigned int offset) -{ - struct s3c_gpio_chip *ourchip = to_s3c_gpio(chip); - void __iomem *base = ourchip->base; - unsigned long con; - - con = __raw_readl(base + GPIOCON_OFF); - con &= ~(0xf << con_4bit_shift(offset)); - __raw_writel(con, base + GPIOCON_OFF); - - gpio_dbg("%s: %p: CON now %08lx\n", __func__, base, con); - - return 0; -} - -static int samsung_gpiolib_4bit_output(struct gpio_chip *chip, - unsigned int offset, int value) -{ - struct s3c_gpio_chip *ourchip = to_s3c_gpio(chip); - void __iomem *base = ourchip->base; - unsigned long con; - unsigned long dat; - - con = __raw_readl(base + GPIOCON_OFF); - con &= ~(0xf << con_4bit_shift(offset)); - con |= 0x1 << con_4bit_shift(offset); - - dat = __raw_readl(base + GPIODAT_OFF); - - if (value) - dat |= 1 << offset; - else - dat &= ~(1 << offset); - - __raw_writel(dat, base + GPIODAT_OFF); - __raw_writel(con, base + GPIOCON_OFF); - __raw_writel(dat, base + GPIODAT_OFF); - - gpio_dbg("%s: %p: CON %08lx, DAT %08lx\n", __func__, base, con, dat); - - return 0; -} - -/* The next set of routines are for the case where the GPIO configuration - * registers are 4 bits per GPIO but there is more than one register (the - * bank has more than 8 GPIOs. - * - * This case is the similar to the 4 bit case, but the registers are as - * follows: - * - * base + 0x00: Control register, 4 bits per gpio (lower 8 GPIOs) - * gpio n: 4 bits starting at (4*n) - * 0000 = input, 0001 = output, others mean special-function - * base + 0x04: Control register, 4 bits per gpio (up to 8 additions GPIOs) - * gpio n: 4 bits starting at (4*n) - * 0000 = input, 0001 = output, others mean special-function - * base + 0x08: Data register, 1 bit per gpio - * bit n: data bit n - * - * To allow us to use the s3c_gpiolib_get and s3c_gpiolib_set routines we - * store the 'base + 0x4' address so that these routines see the data - * register at ourchip->base + 0x04. - */ - -static int samsung_gpiolib_4bit2_input(struct gpio_chip *chip, - unsigned int offset) -{ - struct s3c_gpio_chip *ourchip = to_s3c_gpio(chip); - void __iomem *base = ourchip->base; - void __iomem *regcon = base; - unsigned long con; - - if (offset > 7) - offset -= 8; - else - regcon -= 4; - - con = __raw_readl(regcon); - con &= ~(0xf << con_4bit_shift(offset)); - __raw_writel(con, regcon); - - gpio_dbg("%s: %p: CON %08lx\n", __func__, base, con); - - return 0; -} - -static int samsung_gpiolib_4bit2_output(struct gpio_chip *chip, - unsigned int offset, int value) -{ - struct s3c_gpio_chip *ourchip = to_s3c_gpio(chip); - void __iomem *base = ourchip->base; - void __iomem *regcon = base; - unsigned long con; - unsigned long dat; - unsigned con_offset = offset; - - if (con_offset > 7) - con_offset -= 8; - else - regcon -= 4; - - con = __raw_readl(regcon); - con &= ~(0xf << con_4bit_shift(con_offset)); - con |= 0x1 << con_4bit_shift(con_offset); - - dat = __raw_readl(base + GPIODAT_OFF); - - if (value) - dat |= 1 << offset; - else - dat &= ~(1 << offset); - - __raw_writel(dat, base + GPIODAT_OFF); - __raw_writel(con, regcon); - __raw_writel(dat, base + GPIODAT_OFF); - - gpio_dbg("%s: %p: CON %08lx, DAT %08lx\n", __func__, base, con, dat); - - return 0; -} - -void __init samsung_gpiolib_add_4bit(struct s3c_gpio_chip *chip) -{ - chip->chip.direction_input = samsung_gpiolib_4bit_input; - chip->chip.direction_output = samsung_gpiolib_4bit_output; - chip->pm = __gpio_pm(&s3c_gpio_pm_4bit); -} - -void __init samsung_gpiolib_add_4bit2(struct s3c_gpio_chip *chip) -{ - chip->chip.direction_input = samsung_gpiolib_4bit2_input; - chip->chip.direction_output = samsung_gpiolib_4bit2_output; - chip->pm = __gpio_pm(&s3c_gpio_pm_4bit); -} - -void __init samsung_gpiolib_add_4bit_chips(struct s3c_gpio_chip *chip, - int nr_chips) -{ - for (; nr_chips > 0; nr_chips--, chip++) { - samsung_gpiolib_add_4bit(chip); - s3c_gpiolib_add(chip); - } -} - -void __init samsung_gpiolib_add_4bit2_chips(struct s3c_gpio_chip *chip, - int nr_chips) -{ - for (; nr_chips > 0; nr_chips--, chip++) { - samsung_gpiolib_add_4bit2(chip); - s3c_gpiolib_add(chip); - } -} - -void __init samsung_gpiolib_add_2bit_chips(struct s3c_gpio_chip *chip, - int nr_chips) -{ - for (; nr_chips > 0; nr_chips--, chip++) - s3c_gpiolib_add(chip); -} diff --git a/drivers/gpio/gpio-s5pc100.c b/drivers/gpio/gpio-s5pc100.c deleted file mode 100644 index 7f87b0c76e0..00000000000 --- a/drivers/gpio/gpio-s5pc100.c +++ /dev/null @@ -1,354 +0,0 @@ -/* - * S5PC100 - GPIOlib support - * - * Copyright (c) 2010 Samsung Electronics Co., Ltd. - * http://www.samsung.com - * - * Copyright 2009 Samsung Electronics Co - * Kyungmin Park <kyungmin.park@samsung.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/irq.h> -#include <linux/io.h> -#include <linux/gpio.h> - -#include <mach/map.h> -#include <mach/regs-gpio.h> - -#include <plat/gpio-core.h> -#include <plat/gpio-cfg.h> -#include <plat/gpio-cfg-helpers.h> - -/* S5PC100 GPIO bank summary: - * - * Bank GPIOs Style INT Type - * A0 8 4Bit GPIO_INT0 - * A1 5 4Bit GPIO_INT1 - * B 8 4Bit GPIO_INT2 - * C 5 4Bit GPIO_INT3 - * D 7 4Bit GPIO_INT4 - * E0 8 4Bit GPIO_INT5 - * E1 6 4Bit GPIO_INT6 - * F0 8 4Bit GPIO_INT7 - * F1 8 4Bit GPIO_INT8 - * F2 8 4Bit GPIO_INT9 - * F3 4 4Bit GPIO_INT10 - * G0 8 4Bit GPIO_INT11 - * G1 3 4Bit GPIO_INT12 - * G2 7 4Bit GPIO_INT13 - * G3 7 4Bit GPIO_INT14 - * H0 8 4Bit WKUP_INT - * H1 8 4Bit WKUP_INT - * H2 8 4Bit WKUP_INT - * H3 8 4Bit WKUP_INT - * I 8 4Bit GPIO_INT15 - * J0 8 4Bit GPIO_INT16 - * J1 5 4Bit GPIO_INT17 - * J2 8 4Bit GPIO_INT18 - * J3 8 4Bit GPIO_INT19 - * J4 4 4Bit GPIO_INT20 - * K0 8 4Bit None - * K1 6 4Bit None - * K2 8 4Bit None - * K3 8 4Bit None - * L0 8 4Bit None - * L1 8 4Bit None - * L2 8 4Bit None - * L3 8 4Bit None - */ - -static struct s3c_gpio_cfg gpio_cfg = { - .set_config = s3c_gpio_setcfg_s3c64xx_4bit, - .set_pull = s3c_gpio_setpull_updown, - .get_pull = s3c_gpio_getpull_updown, -}; - -static struct s3c_gpio_cfg gpio_cfg_eint = { - .cfg_eint = 0xf, - .set_config = s3c_gpio_setcfg_s3c64xx_4bit, - .set_pull = s3c_gpio_setpull_updown, - .get_pull = s3c_gpio_getpull_updown, -}; - -static struct s3c_gpio_cfg gpio_cfg_noint = { - .set_config = s3c_gpio_setcfg_s3c64xx_4bit, - .set_pull = s3c_gpio_setpull_updown, - .get_pull = s3c_gpio_getpull_updown, -}; - -/* - * GPIO bank's base address given the index of the bank in the - * list of all gpio banks. - */ -#define S5PC100_BANK_BASE(bank_nr) (S5P_VA_GPIO + ((bank_nr) * 0x20)) - -/* - * Following are the gpio banks in S5PC100. - * - * The 'config' member when left to NULL, is initialized to the default - * structure gpio_cfg in the init function below. - * - * The 'base' member is also initialized in the init function below. - * Note: The initialization of 'base' member of s3c_gpio_chip structure - * uses the above macro and depends on the banks being listed in order here. - */ -static struct s3c_gpio_chip s5pc100_gpio_chips[] = { - { - .chip = { - .base = S5PC100_GPA0(0), - .ngpio = S5PC100_GPIO_A0_NR, - .label = "GPA0", - }, - }, { - .chip = { - .base = S5PC100_GPA1(0), - .ngpio = S5PC100_GPIO_A1_NR, - .label = "GPA1", - }, - }, { - .chip = { - .base = S5PC100_GPB(0), - .ngpio = S5PC100_GPIO_B_NR, - .label = "GPB", - }, - }, { - .chip = { - .base = S5PC100_GPC(0), - .ngpio = S5PC100_GPIO_C_NR, - .label = "GPC", - }, - }, { - .chip = { - .base = S5PC100_GPD(0), - .ngpio = S5PC100_GPIO_D_NR, - .label = "GPD", - }, - }, { - .chip = { - .base = S5PC100_GPE0(0), - .ngpio = S5PC100_GPIO_E0_NR, - .label = "GPE0", - }, - }, { - .chip = { - .base = S5PC100_GPE1(0), - .ngpio = S5PC100_GPIO_E1_NR, - .label = "GPE1", - }, - }, { - .chip = { - .base = S5PC100_GPF0(0), - .ngpio = S5PC100_GPIO_F0_NR, - .label = "GPF0", - }, - }, { - .chip = { - .base = S5PC100_GPF1(0), - .ngpio = S5PC100_GPIO_F1_NR, - .label = "GPF1", - }, - }, { - .chip = { - .base = S5PC100_GPF2(0), - .ngpio = S5PC100_GPIO_F2_NR, - .label = "GPF2", - }, - }, { - .chip = { - .base = S5PC100_GPF3(0), - .ngpio = S5PC100_GPIO_F3_NR, - .label = "GPF3", - }, - }, { - .chip = { - .base = S5PC100_GPG0(0), - .ngpio = S5PC100_GPIO_G0_NR, - .label = "GPG0", - }, - }, { - .chip = { - .base = S5PC100_GPG1(0), - .ngpio = S5PC100_GPIO_G1_NR, - .label = "GPG1", - }, - }, { - .chip = { - .base = S5PC100_GPG2(0), - .ngpio = S5PC100_GPIO_G2_NR, - .label = "GPG2", - }, - }, { - .chip = { - .base = S5PC100_GPG3(0), - .ngpio = S5PC100_GPIO_G3_NR, - .label = "GPG3", - }, - }, { - .chip = { - .base = S5PC100_GPI(0), - .ngpio = S5PC100_GPIO_I_NR, - .label = "GPI", - }, - }, { - .chip = { - .base = S5PC100_GPJ0(0), - .ngpio = S5PC100_GPIO_J0_NR, - .label = "GPJ0", - }, - }, { - .chip = { - .base = S5PC100_GPJ1(0), - .ngpio = S5PC100_GPIO_J1_NR, - .label = "GPJ1", - }, - }, { - .chip = { - .base = S5PC100_GPJ2(0), - .ngpio = S5PC100_GPIO_J2_NR, - .label = "GPJ2", - }, - }, { - .chip = { - .base = S5PC100_GPJ3(0), - .ngpio = S5PC100_GPIO_J3_NR, - .label = "GPJ3", - }, - }, { - .chip = { - .base = S5PC100_GPJ4(0), - .ngpio = S5PC100_GPIO_J4_NR, - .label = "GPJ4", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPK0(0), - .ngpio = S5PC100_GPIO_K0_NR, - .label = "GPK0", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPK1(0), - .ngpio = S5PC100_GPIO_K1_NR, - .label = "GPK1", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPK2(0), - .ngpio = S5PC100_GPIO_K2_NR, - .label = "GPK2", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPK3(0), - .ngpio = S5PC100_GPIO_K3_NR, - .label = "GPK3", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPL0(0), - .ngpio = S5PC100_GPIO_L0_NR, - .label = "GPL0", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPL1(0), - .ngpio = S5PC100_GPIO_L1_NR, - .label = "GPL1", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPL2(0), - .ngpio = S5PC100_GPIO_L2_NR, - .label = "GPL2", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPL3(0), - .ngpio = S5PC100_GPIO_L3_NR, - .label = "GPL3", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PC100_GPL4(0), - .ngpio = S5PC100_GPIO_L4_NR, - .label = "GPL4", - }, - }, { - .base = (S5P_VA_GPIO + 0xC00), - .config = &gpio_cfg_eint, - .irq_base = IRQ_EINT(0), - .chip = { - .base = S5PC100_GPH0(0), - .ngpio = S5PC100_GPIO_H0_NR, - .label = "GPH0", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO + 0xC20), - .config = &gpio_cfg_eint, - .irq_base = IRQ_EINT(8), - .chip = { - .base = S5PC100_GPH1(0), - .ngpio = S5PC100_GPIO_H1_NR, - .label = "GPH1", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO + 0xC40), - .config = &gpio_cfg_eint, - .irq_base = IRQ_EINT(16), - .chip = { - .base = S5PC100_GPH2(0), - .ngpio = S5PC100_GPIO_H2_NR, - .label = "GPH2", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO + 0xC60), - .config = &gpio_cfg_eint, - .irq_base = IRQ_EINT(24), - .chip = { - .base = S5PC100_GPH3(0), - .ngpio = S5PC100_GPIO_H3_NR, - .label = "GPH3", - .to_irq = samsung_gpiolib_to_irq, - }, - }, -}; - -static __init int s5pc100_gpiolib_init(void) -{ - struct s3c_gpio_chip *chip = s5pc100_gpio_chips; - int nr_chips = ARRAY_SIZE(s5pc100_gpio_chips); - int gpioint_group = 0; - int i; - - for (i = 0; i < nr_chips; i++, chip++) { - if (chip->config == NULL) { - chip->config = &gpio_cfg; - chip->group = gpioint_group++; - } - if (chip->base == NULL) - chip->base = S5PC100_BANK_BASE(i); - } - - samsung_gpiolib_add_4bit_chips(s5pc100_gpio_chips, nr_chips); - s5p_register_gpioint_bank(IRQ_GPIOINT, 0, S5P_GPIOINT_GROUP_MAXNR); - - return 0; -} -core_initcall(s5pc100_gpiolib_init); diff --git a/drivers/gpio/gpio-s5pv210.c b/drivers/gpio/gpio-s5pv210.c deleted file mode 100644 index eb12f1602de..00000000000 --- a/drivers/gpio/gpio-s5pv210.c +++ /dev/null @@ -1,287 +0,0 @@ -/* - * S5PV210 - GPIOlib support - * - * Copyright (c) 2010 Samsung Electronics Co., Ltd. - * http://www.samsung.com/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/irq.h> -#include <linux/io.h> -#include <linux/gpio.h> -#include <plat/gpio-core.h> -#include <plat/gpio-cfg.h> -#include <plat/gpio-cfg-helpers.h> -#include <mach/map.h> - -static struct s3c_gpio_cfg gpio_cfg = { - .set_config = s3c_gpio_setcfg_s3c64xx_4bit, - .set_pull = s3c_gpio_setpull_updown, - .get_pull = s3c_gpio_getpull_updown, -}; - -static struct s3c_gpio_cfg gpio_cfg_noint = { - .set_config = s3c_gpio_setcfg_s3c64xx_4bit, - .set_pull = s3c_gpio_setpull_updown, - .get_pull = s3c_gpio_getpull_updown, -}; - -/* GPIO bank's base address given the index of the bank in the - * list of all gpio banks. - */ -#define S5PV210_BANK_BASE(bank_nr) (S5P_VA_GPIO + ((bank_nr) * 0x20)) - -/* - * Following are the gpio banks in v210. - * - * The 'config' member when left to NULL, is initialized to the default - * structure gpio_cfg in the init function below. - * - * The 'base' member is also initialized in the init function below. - * Note: The initialization of 'base' member of s3c_gpio_chip structure - * uses the above macro and depends on the banks being listed in order here. - */ -static struct s3c_gpio_chip s5pv210_gpio_4bit[] = { - { - .chip = { - .base = S5PV210_GPA0(0), - .ngpio = S5PV210_GPIO_A0_NR, - .label = "GPA0", - }, - }, { - .chip = { - .base = S5PV210_GPA1(0), - .ngpio = S5PV210_GPIO_A1_NR, - .label = "GPA1", - }, - }, { - .chip = { - .base = S5PV210_GPB(0), - .ngpio = S5PV210_GPIO_B_NR, - .label = "GPB", - }, - }, { - .chip = { - .base = S5PV210_GPC0(0), - .ngpio = S5PV210_GPIO_C0_NR, - .label = "GPC0", - }, - }, { - .chip = { - .base = S5PV210_GPC1(0), - .ngpio = S5PV210_GPIO_C1_NR, - .label = "GPC1", - }, - }, { - .chip = { - .base = S5PV210_GPD0(0), - .ngpio = S5PV210_GPIO_D0_NR, - .label = "GPD0", - }, - }, { - .chip = { - .base = S5PV210_GPD1(0), - .ngpio = S5PV210_GPIO_D1_NR, - .label = "GPD1", - }, - }, { - .chip = { - .base = S5PV210_GPE0(0), - .ngpio = S5PV210_GPIO_E0_NR, - .label = "GPE0", - }, - }, { - .chip = { - .base = S5PV210_GPE1(0), - .ngpio = S5PV210_GPIO_E1_NR, - .label = "GPE1", - }, - }, { - .chip = { - .base = S5PV210_GPF0(0), - .ngpio = S5PV210_GPIO_F0_NR, - .label = "GPF0", - }, - }, { - .chip = { - .base = S5PV210_GPF1(0), - .ngpio = S5PV210_GPIO_F1_NR, - .label = "GPF1", - }, - }, { - .chip = { - .base = S5PV210_GPF2(0), - .ngpio = S5PV210_GPIO_F2_NR, - .label = "GPF2", - }, - }, { - .chip = { - .base = S5PV210_GPF3(0), - .ngpio = S5PV210_GPIO_F3_NR, - .label = "GPF3", - }, - }, { - .chip = { - .base = S5PV210_GPG0(0), - .ngpio = S5PV210_GPIO_G0_NR, - .label = "GPG0", - }, - }, { - .chip = { - .base = S5PV210_GPG1(0), - .ngpio = S5PV210_GPIO_G1_NR, - .label = "GPG1", - }, - }, { - .chip = { - .base = S5PV210_GPG2(0), - .ngpio = S5PV210_GPIO_G2_NR, - .label = "GPG2", - }, - }, { - .chip = { - .base = S5PV210_GPG3(0), - .ngpio = S5PV210_GPIO_G3_NR, - .label = "GPG3", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PV210_GPI(0), - .ngpio = S5PV210_GPIO_I_NR, - .label = "GPI", - }, - }, { - .chip = { - .base = S5PV210_GPJ0(0), - .ngpio = S5PV210_GPIO_J0_NR, - .label = "GPJ0", - }, - }, { - .chip = { - .base = S5PV210_GPJ1(0), - .ngpio = S5PV210_GPIO_J1_NR, - .label = "GPJ1", - }, - }, { - .chip = { - .base = S5PV210_GPJ2(0), - .ngpio = S5PV210_GPIO_J2_NR, - .label = "GPJ2", - }, - }, { - .chip = { - .base = S5PV210_GPJ3(0), - .ngpio = S5PV210_GPIO_J3_NR, - .label = "GPJ3", - }, - }, { - .chip = { - .base = S5PV210_GPJ4(0), - .ngpio = S5PV210_GPIO_J4_NR, - .label = "GPJ4", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PV210_MP01(0), - .ngpio = S5PV210_GPIO_MP01_NR, - .label = "MP01", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PV210_MP02(0), - .ngpio = S5PV210_GPIO_MP02_NR, - .label = "MP02", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PV210_MP03(0), - .ngpio = S5PV210_GPIO_MP03_NR, - .label = "MP03", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PV210_MP04(0), - .ngpio = S5PV210_GPIO_MP04_NR, - .label = "MP04", - }, - }, { - .config = &gpio_cfg_noint, - .chip = { - .base = S5PV210_MP05(0), - .ngpio = S5PV210_GPIO_MP05_NR, - .label = "MP05", - }, - }, { - .base = (S5P_VA_GPIO + 0xC00), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(0), - .chip = { - .base = S5PV210_GPH0(0), - .ngpio = S5PV210_GPIO_H0_NR, - .label = "GPH0", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO + 0xC20), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(8), - .chip = { - .base = S5PV210_GPH1(0), - .ngpio = S5PV210_GPIO_H1_NR, - .label = "GPH1", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO + 0xC40), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(16), - .chip = { - .base = S5PV210_GPH2(0), - .ngpio = S5PV210_GPIO_H2_NR, - .label = "GPH2", - .to_irq = samsung_gpiolib_to_irq, - }, - }, { - .base = (S5P_VA_GPIO + 0xC60), - .config = &gpio_cfg_noint, - .irq_base = IRQ_EINT(24), - .chip = { - .base = S5PV210_GPH3(0), - .ngpio = S5PV210_GPIO_H3_NR, - .label = "GPH3", - .to_irq = samsung_gpiolib_to_irq, - }, - }, -}; - -static __init int s5pv210_gpiolib_init(void) -{ - struct s3c_gpio_chip *chip = s5pv210_gpio_4bit; - int nr_chips = ARRAY_SIZE(s5pv210_gpio_4bit); - int gpioint_group = 0; - int i = 0; - - for (i = 0; i < nr_chips; i++, chip++) { - if (chip->config == NULL) { - chip->config = &gpio_cfg; - chip->group = gpioint_group++; - } - if (chip->base == NULL) - chip->base = S5PV210_BANK_BASE(i); - } - - samsung_gpiolib_add_4bit_chips(s5pv210_gpio_4bit, nr_chips); - s5p_register_gpioint_bank(IRQ_GPIOINT, 0, S5P_GPIOINT_GROUP_MAXNR); - - return 0; -} -core_initcall(s5pv210_gpiolib_init); diff --git a/drivers/gpio/gpio-samsung.c b/drivers/gpio/gpio-samsung.c new file mode 100644 index 00000000000..b6be77ae497 --- /dev/null +++ b/drivers/gpio/gpio-samsung.c @@ -0,0 +1,2688 @@ +/* + * Copyright (c) 2009-2011 Samsung Electronics Co., Ltd. + * http://www.samsung.com/ + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * http://armlinux.simtec.co.uk/ + * + * SAMSUNG - GPIOlib support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/irq.h> +#include <linux/io.h> +#include <linux/gpio.h> +#include <linux/init.h> +#include <linux/spinlock.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/sysdev.h> +#include <linux/ioport.h> + +#include <asm/irq.h> + +#include <mach/hardware.h> +#include <mach/map.h> +#include <mach/regs-clock.h> +#include <mach/regs-gpio.h> + +#include <plat/cpu.h> +#include <plat/gpio-core.h> +#include <plat/gpio-cfg.h> +#include <plat/gpio-cfg-helpers.h> +#include <plat/gpio-fns.h> +#include <plat/pm.h> + +#ifndef DEBUG_GPIO +#define gpio_dbg(x...) do { } while (0) +#else +#define gpio_dbg(x...) printk(KERN_DEBUG x) +#endif + +int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull) +{ + void __iomem *reg = chip->base + 0x08; + int shift = off * 2; + u32 pup; + + pup = __raw_readl(reg); + pup &= ~(3 << shift); + pup |= pull << shift; + __raw_writel(pup, reg); + + return 0; +} + +samsung_gpio_pull_t samsung_gpio_getpull_updown(struct samsung_gpio_chip *chip, + unsigned int off) +{ + void __iomem *reg = chip->base + 0x08; + int shift = off * 2; + u32 pup = __raw_readl(reg); + + pup >>= shift; + pup &= 0x3; + + return (__force samsung_gpio_pull_t)pup; +} + +int s3c2443_gpio_setpull(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull) +{ + switch (pull) { + case S3C_GPIO_PULL_NONE: + pull = 0x01; + break; + case S3C_GPIO_PULL_UP: + pull = 0x00; + break; + case S3C_GPIO_PULL_DOWN: + pull = 0x02; + break; + } + return samsung_gpio_setpull_updown(chip, off, pull); +} + +samsung_gpio_pull_t s3c2443_gpio_getpull(struct samsung_gpio_chip *chip, + unsigned int off) +{ + samsung_gpio_pull_t pull; + + pull = samsung_gpio_getpull_updown(chip, off); + + switch (pull) { + case 0x00: + pull = S3C_GPIO_PULL_UP; + break; + case 0x01: + case 0x03: + pull = S3C_GPIO_PULL_NONE; + break; + case 0x02: + pull = S3C_GPIO_PULL_DOWN; + break; + } + + return pull; +} + +static int s3c24xx_gpio_setpull_1(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull, + samsung_gpio_pull_t updown) +{ + void __iomem *reg = chip->base + 0x08; + u32 pup = __raw_readl(reg); + + if (pull == updown) + pup &= ~(1 << off); + else if (pull == S3C_GPIO_PULL_NONE) + pup |= (1 << off); + else + return -EINVAL; + + __raw_writel(pup, reg); + return 0; +} + +static samsung_gpio_pull_t s3c24xx_gpio_getpull_1(struct samsung_gpio_chip *chip, + unsigned int off, + samsung_gpio_pull_t updown) +{ + void __iomem *reg = chip->base + 0x08; + u32 pup = __raw_readl(reg); + + pup &= (1 << off); + return pup ? S3C_GPIO_PULL_NONE : updown; +} + +samsung_gpio_pull_t s3c24xx_gpio_getpull_1up(struct samsung_gpio_chip *chip, + unsigned int off) +{ + return s3c24xx_gpio_getpull_1(chip, off, S3C_GPIO_PULL_UP); +} + +int s3c24xx_gpio_setpull_1up(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull) +{ + return s3c24xx_gpio_setpull_1(chip, off, pull, S3C_GPIO_PULL_UP); +} + +samsung_gpio_pull_t s3c24xx_gpio_getpull_1down(struct samsung_gpio_chip *chip, + unsigned int off) +{ + return s3c24xx_gpio_getpull_1(chip, off, S3C_GPIO_PULL_DOWN); +} + +int s3c24xx_gpio_setpull_1down(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull) +{ + return s3c24xx_gpio_setpull_1(chip, off, pull, S3C_GPIO_PULL_DOWN); +} + +static int exynos4_gpio_setpull(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull) +{ + if (pull == S3C_GPIO_PULL_UP) + pull = 3; + + return samsung_gpio_setpull_updown(chip, off, pull); +} + +static samsung_gpio_pull_t exynos4_gpio_getpull(struct samsung_gpio_chip *chip, + unsigned int off) +{ + samsung_gpio_pull_t pull; + + pull = samsung_gpio_getpull_updown(chip, off); + + if (pull == 3) + pull = S3C_GPIO_PULL_UP; + + return pull; +} + +/* + * samsung_gpio_setcfg_2bit - Samsung 2bit style GPIO configuration. + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * @cfg: The configuration value to set. + * + * This helper deal with the GPIO cases where the control register + * has two bits of configuration per gpio, which have the following + * functions: + * 00 = input + * 01 = output + * 1x = special function + */ + +static int samsung_gpio_setcfg_2bit(struct samsung_gpio_chip *chip, + unsigned int off, unsigned int cfg) +{ + void __iomem *reg = chip->base; + unsigned int shift = off * 2; + u32 con; + + if (samsung_gpio_is_cfg_special(cfg)) { + cfg &= 0xf; + if (cfg > 3) + return -EINVAL; + + cfg <<= shift; + } + + con = __raw_readl(reg); + con &= ~(0x3 << shift); + con |= cfg; + __raw_writel(con, reg); + + return 0; +} + +/* + * samsung_gpio_getcfg_2bit - Samsung 2bit style GPIO configuration read. + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * + * The reverse of samsung_gpio_setcfg_2bit(). Will return a value whicg + * could be directly passed back to samsung_gpio_setcfg_2bit(), from the + * S3C_GPIO_SPECIAL() macro. + */ + +static unsigned int samsung_gpio_getcfg_2bit(struct samsung_gpio_chip *chip, + unsigned int off) +{ + u32 con; + + con = __raw_readl(chip->base); + con >>= off * 2; + con &= 3; + + /* this conversion works for IN and OUT as well as special mode */ + return S3C_GPIO_SPECIAL(con); +} + +/* + * samsung_gpio_setcfg_4bit - Samsung 4bit single register GPIO config. + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * @cfg: The configuration value to set. + * + * This helper deal with the GPIO cases where the control register has 4 bits + * of control per GPIO, generally in the form of: + * 0000 = Input + * 0001 = Output + * others = Special functions (dependent on bank) + * + * Note, since the code to deal with the case where there are two control + * registers instead of one, we do not have a separate set of functions for + * each case. + */ + +static int samsung_gpio_setcfg_4bit(struct samsung_gpio_chip *chip, + unsigned int off, unsigned int cfg) +{ + void __iomem *reg = chip->base; + unsigned int shift = (off & 7) * 4; + u32 con; + + if (off < 8 && chip->chip.ngpio > 8) + reg -= 4; + + if (samsung_gpio_is_cfg_special(cfg)) { + cfg &= 0xf; + cfg <<= shift; + } + + con = __raw_readl(reg); + con &= ~(0xf << shift); + con |= cfg; + __raw_writel(con, reg); + + return 0; +} + +/* + * samsung_gpio_getcfg_4bit - Samsung 4bit single register GPIO config read. + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * + * The reverse of samsung_gpio_setcfg_4bit(), turning a gpio configuration + * register setting into a value the software can use, such as could be passed + * to samsung_gpio_setcfg_4bit(). + * + * @sa samsung_gpio_getcfg_2bit + */ + +static unsigned samsung_gpio_getcfg_4bit(struct samsung_gpio_chip *chip, + unsigned int off) +{ + void __iomem *reg = chip->base; + unsigned int shift = (off & 7) * 4; + u32 con; + + if (off < 8 && chip->chip.ngpio > 8) + reg -= 4; + + con = __raw_readl(reg); + con >>= shift; + con &= 0xf; + + /* this conversion works for IN and OUT as well as special mode */ + return S3C_GPIO_SPECIAL(con); +} + +/* + * s3c24xx_gpio_setcfg_abank - S3C24XX style GPIO configuration (Bank A) + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * @cfg: The configuration value to set. + * + * This helper deal with the GPIO cases where the control register + * has one bit of configuration for the gpio, where setting the bit + * means the pin is in special function mode and unset means output. + */ + +static int s3c24xx_gpio_setcfg_abank(struct samsung_gpio_chip *chip, + unsigned int off, unsigned int cfg) +{ + void __iomem *reg = chip->base; + unsigned int shift = off; + u32 con; + + if (samsung_gpio_is_cfg_special(cfg)) { + cfg &= 0xf; + + /* Map output to 0, and SFN2 to 1 */ + cfg -= 1; + if (cfg > 1) + return -EINVAL; + + cfg <<= shift; + } + + con = __raw_readl(reg); + con &= ~(0x1 << shift); + con |= cfg; + __raw_writel(con, reg); + + return 0; +} + +/* + * s3c24xx_gpio_getcfg_abank - S3C24XX style GPIO configuration read (Bank A) + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * + * The reverse of s3c24xx_gpio_setcfg_abank() turning an GPIO into a usable + * GPIO configuration value. + * + * @sa samsung_gpio_getcfg_2bit + * @sa samsung_gpio_getcfg_4bit + */ + +static unsigned s3c24xx_gpio_getcfg_abank(struct samsung_gpio_chip *chip, + unsigned int off) +{ + u32 con; + + con = __raw_readl(chip->base); + con >>= off; + con &= 1; + con++; + + return S3C_GPIO_SFN(con); +} + +static int s5p64x0_gpio_setcfg_rbank(struct samsung_gpio_chip *chip, + unsigned int off, unsigned int cfg) +{ + void __iomem *reg = chip->base; + unsigned int shift; + u32 con; + + switch (off) { + case 0: + case 1: + case 2: + case 3: + case 4: + case 5: + shift = (off & 7) * 4; + reg -= 4; + break; + case 6: + shift = ((off + 1) & 7) * 4; + reg -= 4; + default: + shift = ((off + 1) & 7) * 4; + break; + } + + if (samsung_gpio_is_cfg_special(cfg)) { + cfg &= 0xf; + cfg <<= shift; + } + + con = __raw_readl(reg); + con &= ~(0xf << shift); + con |= cfg; + __raw_writel(con, reg); + + return 0; +} + +static void __init samsung_gpiolib_set_cfg(struct samsung_gpio_cfg *chipcfg, + int nr_chips) +{ + for (; nr_chips > 0; nr_chips--, chipcfg++) { + if (!chipcfg->set_config) + chipcfg->set_config = samsung_gpio_setcfg_4bit; + if (!chipcfg->get_config) + chipcfg->get_config = samsung_gpio_getcfg_4bit; + if (!chipcfg->set_pull) + chipcfg->set_pull = samsung_gpio_setpull_updown; + if (!chipcfg->get_pull) + chipcfg->get_pull = samsung_gpio_getpull_updown; + } +} + +struct samsung_gpio_cfg s3c24xx_gpiocfg_default = { + .set_config = samsung_gpio_setcfg_2bit, + .get_config = samsung_gpio_getcfg_2bit, +}; + +static struct samsung_gpio_cfg s3c24xx_gpiocfg_banka = { + .set_config = s3c24xx_gpio_setcfg_abank, + .get_config = s3c24xx_gpio_getcfg_abank, +}; + +static struct samsung_gpio_cfg exynos4_gpio_cfg = { + .set_pull = exynos4_gpio_setpull, + .get_pull = exynos4_gpio_getpull, + .set_config = samsung_gpio_setcfg_4bit, + .get_config = samsung_gpio_getcfg_4bit, +}; + +static struct samsung_gpio_cfg s5p64x0_gpio_cfg_rbank = { + .cfg_eint = 0x3, + .set_config = s5p64x0_gpio_setcfg_rbank, + .get_config = samsung_gpio_getcfg_4bit, + .set_pull = samsung_gpio_setpull_updown, + .get_pull = samsung_gpio_getpull_updown, +}; + +static struct samsung_gpio_cfg samsung_gpio_cfgs[] = { + { + .cfg_eint = 0x0, + }, { + .cfg_eint = 0x3, + }, { + .cfg_eint = 0x7, + }, { + .cfg_eint = 0xF, + }, { + .cfg_eint = 0x0, + .set_config = samsung_gpio_setcfg_2bit, + .get_config = samsung_gpio_getcfg_2bit, + }, { + .cfg_eint = 0x2, + .set_config = samsung_gpio_setcfg_2bit, + .get_config = samsung_gpio_getcfg_2bit, + }, { + .cfg_eint = 0x3, + .set_config = samsung_gpio_setcfg_2bit, + .get_config = samsung_gpio_getcfg_2bit, + }, { + .set_config = samsung_gpio_setcfg_2bit, + .get_config = samsung_gpio_getcfg_2bit, + }, +}; + +/* + * Default routines for controlling GPIO, based on the original S3C24XX + * GPIO functions which deal with the case where each gpio bank of the + * chip is as following: + * + * base + 0x00: Control register, 2 bits per gpio + * gpio n: 2 bits starting at (2*n) + * 00 = input, 01 = output, others mean special-function + * base + 0x04: Data register, 1 bit per gpio + * bit n: data bit n +*/ + +static int samsung_gpiolib_2bit_input(struct gpio_chip *chip, unsigned offset) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long con; + + samsung_gpio_lock(ourchip, flags); + + con = __raw_readl(base + 0x00); + con &= ~(3 << (offset * 2)); + + __raw_writel(con, base + 0x00); + + samsung_gpio_unlock(ourchip, flags); + return 0; +} + +static int samsung_gpiolib_2bit_output(struct gpio_chip *chip, + unsigned offset, int value) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long dat; + unsigned long con; + + samsung_gpio_lock(ourchip, flags); + + dat = __raw_readl(base + 0x04); + dat &= ~(1 << offset); + if (value) + dat |= 1 << offset; + __raw_writel(dat, base + 0x04); + + con = __raw_readl(base + 0x00); + con &= ~(3 << (offset * 2)); + con |= 1 << (offset * 2); + + __raw_writel(con, base + 0x00); + __raw_writel(dat, base + 0x04); + + samsung_gpio_unlock(ourchip, flags); + return 0; +} + +/* + * The samsung_gpiolib_4bit routines are to control the gpio banks where + * the gpio configuration register (GPxCON) has 4 bits per GPIO, as the + * following example: + * + * base + 0x00: Control register, 4 bits per gpio + * gpio n: 4 bits starting at (4*n) + * 0000 = input, 0001 = output, others mean special-function + * base + 0x04: Data register, 1 bit per gpio + * bit n: data bit n + * + * Note, since the data register is one bit per gpio and is at base + 0x4 + * we can use samsung_gpiolib_get and samsung_gpiolib_set to change the + * state of the output. + */ + +static int samsung_gpiolib_4bit_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + unsigned long con; + + con = __raw_readl(base + GPIOCON_OFF); + con &= ~(0xf << con_4bit_shift(offset)); + __raw_writel(con, base + GPIOCON_OFF); + + gpio_dbg("%s: %p: CON now %08lx\n", __func__, base, con); + + return 0; +} + +static int samsung_gpiolib_4bit_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + unsigned long con; + unsigned long dat; + + con = __raw_readl(base + GPIOCON_OFF); + con &= ~(0xf << con_4bit_shift(offset)); + con |= 0x1 << con_4bit_shift(offset); + + dat = __raw_readl(base + GPIODAT_OFF); + + if (value) + dat |= 1 << offset; + else + dat &= ~(1 << offset); + + __raw_writel(dat, base + GPIODAT_OFF); + __raw_writel(con, base + GPIOCON_OFF); + __raw_writel(dat, base + GPIODAT_OFF); + + gpio_dbg("%s: %p: CON %08lx, DAT %08lx\n", __func__, base, con, dat); + + return 0; +} + +/* + * The next set of routines are for the case where the GPIO configuration + * registers are 4 bits per GPIO but there is more than one register (the + * bank has more than 8 GPIOs. + * + * This case is the similar to the 4 bit case, but the registers are as + * follows: + * + * base + 0x00: Control register, 4 bits per gpio (lower 8 GPIOs) + * gpio n: 4 bits starting at (4*n) + * 0000 = input, 0001 = output, others mean special-function + * base + 0x04: Control register, 4 bits per gpio (up to 8 additions GPIOs) + * gpio n: 4 bits starting at (4*n) + * 0000 = input, 0001 = output, others mean special-function + * base + 0x08: Data register, 1 bit per gpio + * bit n: data bit n + * + * To allow us to use the samsung_gpiolib_get and samsung_gpiolib_set + * routines we store the 'base + 0x4' address so that these routines see + * the data register at ourchip->base + 0x04. + */ + +static int samsung_gpiolib_4bit2_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + void __iomem *regcon = base; + unsigned long con; + + if (offset > 7) + offset -= 8; + else + regcon -= 4; + + con = __raw_readl(regcon); + con &= ~(0xf << con_4bit_shift(offset)); + __raw_writel(con, regcon); + + gpio_dbg("%s: %p: CON %08lx\n", __func__, base, con); + + return 0; +} + +static int samsung_gpiolib_4bit2_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + void __iomem *regcon = base; + unsigned long con; + unsigned long dat; + unsigned con_offset = offset; + + if (con_offset > 7) + con_offset -= 8; + else + regcon -= 4; + + con = __raw_readl(regcon); + con &= ~(0xf << con_4bit_shift(con_offset)); + con |= 0x1 << con_4bit_shift(con_offset); + + dat = __raw_readl(base + GPIODAT_OFF); + + if (value) + dat |= 1 << offset; + else + dat &= ~(1 << offset); + + __raw_writel(dat, base + GPIODAT_OFF); + __raw_writel(con, regcon); + __raw_writel(dat, base + GPIODAT_OFF); + + gpio_dbg("%s: %p: CON %08lx, DAT %08lx\n", __func__, base, con, dat); + + return 0; +} + +/* The next set of routines are for the case of s3c24xx bank a */ + +static int s3c24xx_gpiolib_banka_input(struct gpio_chip *chip, unsigned offset) +{ + return -EINVAL; +} + +static int s3c24xx_gpiolib_banka_output(struct gpio_chip *chip, + unsigned offset, int value) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long dat; + unsigned long con; + + local_irq_save(flags); + + con = __raw_readl(base + 0x00); + dat = __raw_readl(base + 0x04); + + dat &= ~(1 << offset); + if (value) + dat |= 1 << offset; + + __raw_writel(dat, base + 0x04); + + con &= ~(1 << offset); + + __raw_writel(con, base + 0x00); + __raw_writel(dat, base + 0x04); + + local_irq_restore(flags); + return 0; +} + +/* The next set of routines are for the case of s5p64x0 bank r */ + +static int s5p64x0_gpiolib_rbank_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + void __iomem *regcon = base; + unsigned long con; + unsigned long flags; + + switch (offset) { + case 6: + offset += 1; + case 0: + case 1: + case 2: + case 3: + case 4: + case 5: + regcon -= 4; + break; + default: + offset -= 7; + break; + } + + samsung_gpio_lock(ourchip, flags); + + con = __raw_readl(regcon); + con &= ~(0xf << con_4bit_shift(offset)); + __raw_writel(con, regcon); + + samsung_gpio_unlock(ourchip, flags); + + return 0; +} + +static int s5p64x0_gpiolib_rbank_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + void __iomem *regcon = base; + unsigned long con; + unsigned long dat; + unsigned long flags; + unsigned con_offset = offset; + + switch (con_offset) { + case 6: + con_offset += 1; + case 0: + case 1: + case 2: + case 3: + case 4: + case 5: + regcon -= 4; + break; + default: + con_offset -= 7; + break; + } + + samsung_gpio_lock(ourchip, flags); + + con = __raw_readl(regcon); + con &= ~(0xf << con_4bit_shift(con_offset)); + con |= 0x1 << con_4bit_shift(con_offset); + + dat = __raw_readl(base + GPIODAT_OFF); + if (value) + dat |= 1 << offset; + else + dat &= ~(1 << offset); + + __raw_writel(con, regcon); + __raw_writel(dat, base + GPIODAT_OFF); + + samsung_gpio_unlock(ourchip, flags); + + return 0; +} + +static void samsung_gpiolib_set(struct gpio_chip *chip, + unsigned offset, int value) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + void __iomem *base = ourchip->base; + unsigned long flags; + unsigned long dat; + + samsung_gpio_lock(ourchip, flags); + + dat = __raw_readl(base + 0x04); + dat &= ~(1 << offset); + if (value) + dat |= 1 << offset; + __raw_writel(dat, base + 0x04); + + samsung_gpio_unlock(ourchip, flags); +} + +static int samsung_gpiolib_get(struct gpio_chip *chip, unsigned offset) +{ + struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip); + unsigned long val; + + val = __raw_readl(ourchip->base + 0x04); + val >>= offset; + val &= 1; + + return val; +} + +/* + * CONFIG_S3C_GPIO_TRACK enables the tracking of the s3c specific gpios + * for use with the configuration calls, and other parts of the s3c gpiolib + * support code. + * + * Not all s3c support code will need this, as some configurations of cpu + * may only support one or two different configuration options and have an + * easy gpio to samsung_gpio_chip mapping function. If this is the case, then + * the machine support file should provide its own samsung_gpiolib_getchip() + * and any other necessary functions. + */ + +#ifdef CONFIG_S3C_GPIO_TRACK +struct samsung_gpio_chip *s3c_gpios[S3C_GPIO_END]; + +static __init void s3c_gpiolib_track(struct samsung_gpio_chip *chip) +{ + unsigned int gpn; + int i; + + gpn = chip->chip.base; + for (i = 0; i < chip->chip.ngpio; i++, gpn++) { + BUG_ON(gpn >= ARRAY_SIZE(s3c_gpios)); + s3c_gpios[gpn] = chip; + } +} +#endif /* CONFIG_S3C_GPIO_TRACK */ + +/* + * samsung_gpiolib_add() - add the Samsung gpio_chip. + * @chip: The chip to register + * + * This is a wrapper to gpiochip_add() that takes our specific gpio chip + * information and makes the necessary alterations for the platform and + * notes the information for use with the configuration systems and any + * other parts of the system. + */ + +static void __init samsung_gpiolib_add(struct samsung_gpio_chip *chip) +{ + struct gpio_chip *gc = &chip->chip; + int ret; + + BUG_ON(!chip->base); + BUG_ON(!gc->label); + BUG_ON(!gc->ngpio); + + spin_lock_init(&chip->lock); + + if (!gc->direction_input) + gc->direction_input = samsung_gpiolib_2bit_input; + if (!gc->direction_output) + gc->direction_output = samsung_gpiolib_2bit_output; + if (!gc->set) + gc->set = samsung_gpiolib_set; + if (!gc->get) + gc->get = samsung_gpiolib_get; + +#ifdef CONFIG_PM + if (chip->pm != NULL) { + if (!chip->pm->save || !chip->pm->resume) + printk(KERN_ERR "gpio: %s has missing PM functions\n", + gc->label); + } else + printk(KERN_ERR "gpio: %s has no PM function\n", gc->label); +#endif + + /* gpiochip_add() prints own failure message on error. */ + ret = gpiochip_add(gc); + if (ret >= 0) + s3c_gpiolib_track(chip); +} + +static void __init s3c24xx_gpiolib_add_chips(struct samsung_gpio_chip *chip, + int nr_chips, void __iomem *base) +{ + int i; + struct gpio_chip *gc = &chip->chip; + + for (i = 0 ; i < nr_chips; i++, chip++) { + if (!chip->config) + chip->config = &s3c24xx_gpiocfg_default; + if (!chip->pm) + chip->pm = __gpio_pm(&samsung_gpio_pm_2bit); + if ((base != NULL) && (chip->base == NULL)) + chip->base = base + ((i) * 0x10); + + if (!gc->direction_input) + gc->direction_input = samsung_gpiolib_2bit_input; + if (!gc->direction_output) + gc->direction_output = samsung_gpiolib_2bit_output; + + samsung_gpiolib_add(chip); + } +} + +static void __init samsung_gpiolib_add_2bit_chips(struct samsung_gpio_chip *chip, + int nr_chips, void __iomem *base, + unsigned int offset) +{ + int i; + + for (i = 0 ; i < nr_chips; i++, chip++) { + chip->chip.direction_input = samsung_gpiolib_2bit_input; + chip->chip.direction_output = samsung_gpiolib_2bit_output; + + if (!chip->config) + chip->config = &samsung_gpio_cfgs[7]; + if (!chip->pm) + chip->pm = __gpio_pm(&samsung_gpio_pm_2bit); + if ((base != NULL) && (chip->base == NULL)) + chip->base = base + ((i) * offset); + + samsung_gpiolib_add(chip); + } +} + +/* + * samsung_gpiolib_add_4bit_chips - 4bit single register GPIO config. + * @chip: The gpio chip that is being configured. + * @nr_chips: The no of chips (gpio ports) for the GPIO being configured. + * + * This helper deal with the GPIO cases where the control register has 4 bits + * of control per GPIO, generally in the form of: + * 0000 = Input + * 0001 = Output + * others = Special functions (dependent on bank) + * + * Note, since the code to deal with the case where there are two control + * registers instead of one, we do not have a separate set of function + * (samsung_gpiolib_add_4bit2_chips)for each case. + */ + +static void __init samsung_gpiolib_add_4bit_chips(struct samsung_gpio_chip *chip, + int nr_chips, void __iomem *base) +{ + int i; + + for (i = 0 ; i < nr_chips; i++, chip++) { + chip->chip.direction_input = samsung_gpiolib_4bit_input; + chip->chip.direction_output = samsung_gpiolib_4bit_output; + + if (!chip->config) + chip->config = &samsung_gpio_cfgs[2]; + if (!chip->pm) + chip->pm = __gpio_pm(&samsung_gpio_pm_4bit); + if ((base != NULL) && (chip->base == NULL)) + chip->base = base + ((i) * 0x20); + + samsung_gpiolib_add(chip); + } +} + +static void __init samsung_gpiolib_add_4bit2_chips(struct samsung_gpio_chip *chip, + int nr_chips) +{ + for (; nr_chips > 0; nr_chips--, chip++) { + chip->chip.direction_input = samsung_gpiolib_4bit2_input; + chip->chip.direction_output = samsung_gpiolib_4bit2_output; + + if (!chip->config) + chip->config = &samsung_gpio_cfgs[2]; + if (!chip->pm) + chip->pm = __gpio_pm(&samsung_gpio_pm_4bit); + + samsung_gpiolib_add(chip); + } +} + +static void __init s5p64x0_gpiolib_add_rbank(struct samsung_gpio_chip *chip, + int nr_chips) +{ + for (; nr_chips > 0; nr_chips--, chip++) { + chip->chip.direction_input = s5p64x0_gpiolib_rbank_input; + chip->chip.direction_output = s5p64x0_gpiolib_rbank_output; + + if (!chip->pm) + chip->pm = __gpio_pm(&samsung_gpio_pm_4bit); + + samsung_gpiolib_add(chip); + } +} + +int samsung_gpiolib_to_irq(struct gpio_chip *chip, unsigned int offset) +{ + struct samsung_gpio_chip *samsung_chip = container_of(chip, struct samsung_gpio_chip, chip); + + return samsung_chip->irq_base + offset; +} + +#ifdef CONFIG_PLAT_S3C24XX +static int s3c24xx_gpiolib_fbank_to_irq(struct gpio_chip *chip, unsigned offset) +{ + if (offset < 4) + return IRQ_EINT0 + offset; + + if (offset < 8) + return IRQ_EINT4 + offset - 4; + + return -EINVAL; +} +#endif + +#ifdef CONFIG_PLAT_S3C64XX +static int s3c64xx_gpiolib_mbank_to_irq(struct gpio_chip *chip, unsigned pin) +{ + return pin < 5 ? IRQ_EINT(23) + pin : -ENXIO; +} + +static int s3c64xx_gpiolib_lbank_to_irq(struct gpio_chip *chip, unsigned pin) +{ + return pin >= 8 ? IRQ_EINT(16) + pin - 8 : -ENXIO; +} +#endif + +struct samsung_gpio_chip s3c24xx_gpios[] = { +#ifdef CONFIG_PLAT_S3C24XX + { + .config = &s3c24xx_gpiocfg_banka, + .chip = { + .base = S3C2410_GPA(0), + .owner = THIS_MODULE, + .label = "GPIOA", + .ngpio = 24, + .direction_input = s3c24xx_gpiolib_banka_input, + .direction_output = s3c24xx_gpiolib_banka_output, + }, + }, { + .chip = { + .base = S3C2410_GPB(0), + .owner = THIS_MODULE, + .label = "GPIOB", + .ngpio = 16, + }, + }, { + .chip = { + .base = S3C2410_GPC(0), + .owner = THIS_MODULE, + .label = "GPIOC", + .ngpio = 16, + }, + }, { + .chip = { + .base = S3C2410_GPD(0), + .owner = THIS_MODULE, + .label = "GPIOD", + .ngpio = 16, + }, + }, { + .chip = { + .base = S3C2410_GPE(0), + .label = "GPIOE", + .owner = THIS_MODULE, + .ngpio = 16, + }, + }, { + .chip = { + .base = S3C2410_GPF(0), + .owner = THIS_MODULE, + .label = "GPIOF", + .ngpio = 8, + .to_irq = s3c24xx_gpiolib_fbank_to_irq, + }, + }, { + .irq_base = IRQ_EINT8, + .chip = { + .base = S3C2410_GPG(0), + .owner = THIS_MODULE, + .label = "GPIOG", + .ngpio = 16, + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .chip = { + .base = S3C2410_GPH(0), + .owner = THIS_MODULE, + .label = "GPIOH", + .ngpio = 11, + }, + }, + /* GPIOS for the S3C2443 and later devices. */ + { + .base = S3C2440_GPJCON, + .chip = { + .base = S3C2410_GPJ(0), + .owner = THIS_MODULE, + .label = "GPIOJ", + .ngpio = 16, + }, + }, { + .base = S3C2443_GPKCON, + .chip = { + .base = S3C2410_GPK(0), + .owner = THIS_MODULE, + .label = "GPIOK", + .ngpio = 16, + }, + }, { + .base = S3C2443_GPLCON, + .chip = { + .base = S3C2410_GPL(0), + .owner = THIS_MODULE, + .label = "GPIOL", + .ngpio = 15, + }, + }, { + .base = S3C2443_GPMCON, + .chip = { + .base = S3C2410_GPM(0), + .owner = THIS_MODULE, + .label = "GPIOM", + .ngpio = 2, + }, + }, +#endif +}; + +/* + * GPIO bank summary: + * + * Bank GPIOs Style SlpCon ExtInt Group + * A 8 4Bit Yes 1 + * B 7 4Bit Yes 1 + * C 8 4Bit Yes 2 + * D 5 4Bit Yes 3 + * E 5 4Bit Yes None + * F 16 2Bit Yes 4 [1] + * G 7 4Bit Yes 5 + * H 10 4Bit[2] Yes 6 + * I 16 2Bit Yes None + * J 12 2Bit Yes None + * K 16 4Bit[2] No None + * L 15 4Bit[2] No None + * M 6 4Bit No IRQ_EINT + * N 16 2Bit No IRQ_EINT + * O 16 2Bit Yes 7 + * P 15 2Bit Yes 8 + * Q 9 2Bit Yes 9 + * + * [1] BANKF pins 14,15 do not form part of the external interrupt sources + * [2] BANK has two control registers, GPxCON0 and GPxCON1 + */ + +static struct samsung_gpio_chip s3c64xx_gpios_4bit[] = { +#ifdef CONFIG_PLAT_S3C64XX + { + .chip = { + .base = S3C64XX_GPA(0), + .ngpio = S3C64XX_GPIO_A_NR, + .label = "GPA", + }, + }, { + .chip = { + .base = S3C64XX_GPB(0), + .ngpio = S3C64XX_GPIO_B_NR, + .label = "GPB", + }, + }, { + .chip = { + .base = S3C64XX_GPC(0), + .ngpio = S3C64XX_GPIO_C_NR, + .label = "GPC", + }, + }, { + .chip = { + .base = S3C64XX_GPD(0), + .ngpio = S3C64XX_GPIO_D_NR, + .label = "GPD", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = S3C64XX_GPE(0), + .ngpio = S3C64XX_GPIO_E_NR, + .label = "GPE", + }, + }, { + .base = S3C64XX_GPG_BASE, + .chip = { + .base = S3C64XX_GPG(0), + .ngpio = S3C64XX_GPIO_G_NR, + .label = "GPG", + }, + }, { + .base = S3C64XX_GPM_BASE, + .config = &samsung_gpio_cfgs[1], + .chip = { + .base = S3C64XX_GPM(0), + .ngpio = S3C64XX_GPIO_M_NR, + .label = "GPM", + .to_irq = s3c64xx_gpiolib_mbank_to_irq, + }, + }, +#endif +}; + +static struct samsung_gpio_chip s3c64xx_gpios_4bit2[] = { +#ifdef CONFIG_PLAT_S3C64XX + { + .base = S3C64XX_GPH_BASE + 0x4, + .chip = { + .base = S3C64XX_GPH(0), + .ngpio = S3C64XX_GPIO_H_NR, + .label = "GPH", + }, + }, { + .base = S3C64XX_GPK_BASE + 0x4, + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = S3C64XX_GPK(0), + .ngpio = S3C64XX_GPIO_K_NR, + .label = "GPK", + }, + }, { + .base = S3C64XX_GPL_BASE + 0x4, + .config = &samsung_gpio_cfgs[1], + .chip = { + .base = S3C64XX_GPL(0), + .ngpio = S3C64XX_GPIO_L_NR, + .label = "GPL", + .to_irq = s3c64xx_gpiolib_lbank_to_irq, + }, + }, +#endif +}; + +static struct samsung_gpio_chip s3c64xx_gpios_2bit[] = { +#ifdef CONFIG_PLAT_S3C64XX + { + .base = S3C64XX_GPF_BASE, + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S3C64XX_GPF(0), + .ngpio = S3C64XX_GPIO_F_NR, + .label = "GPF", + }, + }, { + .config = &samsung_gpio_cfgs[7], + .chip = { + .base = S3C64XX_GPI(0), + .ngpio = S3C64XX_GPIO_I_NR, + .label = "GPI", + }, + }, { + .config = &samsung_gpio_cfgs[7], + .chip = { + .base = S3C64XX_GPJ(0), + .ngpio = S3C64XX_GPIO_J_NR, + .label = "GPJ", + }, + }, { + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S3C64XX_GPO(0), + .ngpio = S3C64XX_GPIO_O_NR, + .label = "GPO", + }, + }, { + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S3C64XX_GPP(0), + .ngpio = S3C64XX_GPIO_P_NR, + .label = "GPP", + }, + }, { + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S3C64XX_GPQ(0), + .ngpio = S3C64XX_GPIO_Q_NR, + .label = "GPQ", + }, + }, { + .base = S3C64XX_GPN_BASE, + .irq_base = IRQ_EINT(0), + .config = &samsung_gpio_cfgs[5], + .chip = { + .base = S3C64XX_GPN(0), + .ngpio = S3C64XX_GPIO_N_NR, + .label = "GPN", + .to_irq = samsung_gpiolib_to_irq, + }, + }, +#endif +}; + +/* + * S5P6440 GPIO bank summary: + * + * Bank GPIOs Style SlpCon ExtInt Group + * A 6 4Bit Yes 1 + * B 7 4Bit Yes 1 + * C 8 4Bit Yes 2 + * F 2 2Bit Yes 4 [1] + * G 7 4Bit Yes 5 + * H 10 4Bit[2] Yes 6 + * I 16 2Bit Yes None + * J 12 2Bit Yes None + * N 16 2Bit No IRQ_EINT + * P 8 2Bit Yes 8 + * R 15 4Bit[2] Yes 8 + */ + +static struct samsung_gpio_chip s5p6440_gpios_4bit[] = { +#ifdef CONFIG_CPU_S5P6440 + { + .chip = { + .base = S5P6440_GPA(0), + .ngpio = S5P6440_GPIO_A_NR, + .label = "GPA", + }, + }, { + .chip = { + .base = S5P6440_GPB(0), + .ngpio = S5P6440_GPIO_B_NR, + .label = "GPB", + }, + }, { + .chip = { + .base = S5P6440_GPC(0), + .ngpio = S5P6440_GPIO_C_NR, + .label = "GPC", + }, + }, { + .base = S5P64X0_GPG_BASE, + .chip = { + .base = S5P6440_GPG(0), + .ngpio = S5P6440_GPIO_G_NR, + .label = "GPG", + }, + }, +#endif +}; + +static struct samsung_gpio_chip s5p6440_gpios_4bit2[] = { +#ifdef CONFIG_CPU_S5P6440 + { + .base = S5P64X0_GPH_BASE + 0x4, + .chip = { + .base = S5P6440_GPH(0), + .ngpio = S5P6440_GPIO_H_NR, + .label = "GPH", + }, + }, +#endif +}; + +static struct samsung_gpio_chip s5p6440_gpios_rbank[] = { +#ifdef CONFIG_CPU_S5P6440 + { + .base = S5P64X0_GPR_BASE + 0x4, + .config = &s5p64x0_gpio_cfg_rbank, + .chip = { + .base = S5P6440_GPR(0), + .ngpio = S5P6440_GPIO_R_NR, + .label = "GPR", + }, + }, +#endif +}; + +static struct samsung_gpio_chip s5p6440_gpios_2bit[] = { +#ifdef CONFIG_CPU_S5P6440 + { + .base = S5P64X0_GPF_BASE, + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S5P6440_GPF(0), + .ngpio = S5P6440_GPIO_F_NR, + .label = "GPF", + }, + }, { + .base = S5P64X0_GPI_BASE, + .config = &samsung_gpio_cfgs[4], + .chip = { + .base = S5P6440_GPI(0), + .ngpio = S5P6440_GPIO_I_NR, + .label = "GPI", + }, + }, { + .base = S5P64X0_GPJ_BASE, + .config = &samsung_gpio_cfgs[4], + .chip = { + .base = S5P6440_GPJ(0), + .ngpio = S5P6440_GPIO_J_NR, + .label = "GPJ", + }, + }, { + .base = S5P64X0_GPN_BASE, + .config = &samsung_gpio_cfgs[5], + .chip = { + .base = S5P6440_GPN(0), + .ngpio = S5P6440_GPIO_N_NR, + .label = "GPN", + }, + }, { + .base = S5P64X0_GPP_BASE, + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S5P6440_GPP(0), + .ngpio = S5P6440_GPIO_P_NR, + .label = "GPP", + }, + }, +#endif +}; + +/* + * S5P6450 GPIO bank summary: + * + * Bank GPIOs Style SlpCon ExtInt Group + * A 6 4Bit Yes 1 + * B 7 4Bit Yes 1 + * C 8 4Bit Yes 2 + * D 8 4Bit Yes None + * F 2 2Bit Yes None + * G 14 4Bit[2] Yes 5 + * H 10 4Bit[2] Yes 6 + * I 16 2Bit Yes None + * J 12 2Bit Yes None + * K 5 4Bit Yes None + * N 16 2Bit No IRQ_EINT + * P 11 2Bit Yes 8 + * Q 14 2Bit Yes None + * R 15 4Bit[2] Yes None + * S 8 2Bit Yes None + * + * [1] BANKF pins 14,15 do not form part of the external interrupt sources + * [2] BANK has two control registers, GPxCON0 and GPxCON1 + */ + +static struct samsung_gpio_chip s5p6450_gpios_4bit[] = { +#ifdef CONFIG_CPU_S5P6450 + { + .chip = { + .base = S5P6450_GPA(0), + .ngpio = S5P6450_GPIO_A_NR, + .label = "GPA", + }, + }, { + .chip = { + .base = S5P6450_GPB(0), + .ngpio = S5P6450_GPIO_B_NR, + .label = "GPB", + }, + }, { + .chip = { + .base = S5P6450_GPC(0), + .ngpio = S5P6450_GPIO_C_NR, + .label = "GPC", + }, + }, { + .chip = { + .base = S5P6450_GPD(0), + .ngpio = S5P6450_GPIO_D_NR, + .label = "GPD", + }, + }, { + .base = S5P6450_GPK_BASE, + .chip = { + .base = S5P6450_GPK(0), + .ngpio = S5P6450_GPIO_K_NR, + .label = "GPK", + }, + }, +#endif +}; + +static struct samsung_gpio_chip s5p6450_gpios_4bit2[] = { +#ifdef CONFIG_CPU_S5P6450 + { + .base = S5P64X0_GPG_BASE + 0x4, + .chip = { + .base = S5P6450_GPG(0), + .ngpio = S5P6450_GPIO_G_NR, + .label = "GPG", + }, + }, { + .base = S5P64X0_GPH_BASE + 0x4, + .chip = { + .base = S5P6450_GPH(0), + .ngpio = S5P6450_GPIO_H_NR, + .label = "GPH", + }, + }, +#endif +}; + +static struct samsung_gpio_chip s5p6450_gpios_rbank[] = { +#ifdef CONFIG_CPU_S5P6450 + { + .base = S5P64X0_GPR_BASE + 0x4, + .config = &s5p64x0_gpio_cfg_rbank, + .chip = { + .base = S5P6450_GPR(0), + .ngpio = S5P6450_GPIO_R_NR, + .label = "GPR", + }, + }, +#endif +}; + +static struct samsung_gpio_chip s5p6450_gpios_2bit[] = { +#ifdef CONFIG_CPU_S5P6450 + { + .base = S5P64X0_GPF_BASE, + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S5P6450_GPF(0), + .ngpio = S5P6450_GPIO_F_NR, + .label = "GPF", + }, + }, { + .base = S5P64X0_GPI_BASE, + .config = &samsung_gpio_cfgs[4], + .chip = { + .base = S5P6450_GPI(0), + .ngpio = S5P6450_GPIO_I_NR, + .label = "GPI", + }, + }, { + .base = S5P64X0_GPJ_BASE, + .config = &samsung_gpio_cfgs[4], + .chip = { + .base = S5P6450_GPJ(0), + .ngpio = S5P6450_GPIO_J_NR, + .label = "GPJ", + }, + }, { + .base = S5P64X0_GPN_BASE, + .config = &samsung_gpio_cfgs[5], + .chip = { + .base = S5P6450_GPN(0), + .ngpio = S5P6450_GPIO_N_NR, + .label = "GPN", + }, + }, { + .base = S5P64X0_GPP_BASE, + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S5P6450_GPP(0), + .ngpio = S5P6450_GPIO_P_NR, + .label = "GPP", + }, + }, { + .base = S5P6450_GPQ_BASE, + .config = &samsung_gpio_cfgs[5], + .chip = { + .base = S5P6450_GPQ(0), + .ngpio = S5P6450_GPIO_Q_NR, + .label = "GPQ", + }, + }, { + .base = S5P6450_GPS_BASE, + .config = &samsung_gpio_cfgs[6], + .chip = { + .base = S5P6450_GPS(0), + .ngpio = S5P6450_GPIO_S_NR, + .label = "GPS", + }, + }, +#endif +}; + +/* + * S5PC100 GPIO bank summary: + * + * Bank GPIOs Style INT Type + * A0 8 4Bit GPIO_INT0 + * A1 5 4Bit GPIO_INT1 + * B 8 4Bit GPIO_INT2 + * C 5 4Bit GPIO_INT3 + * D 7 4Bit GPIO_INT4 + * E0 8 4Bit GPIO_INT5 + * E1 6 4Bit GPIO_INT6 + * F0 8 4Bit GPIO_INT7 + * F1 8 4Bit GPIO_INT8 + * F2 8 4Bit GPIO_INT9 + * F3 4 4Bit GPIO_INT10 + * G0 8 4Bit GPIO_INT11 + * G1 3 4Bit GPIO_INT12 + * G2 7 4Bit GPIO_INT13 + * G3 7 4Bit GPIO_INT14 + * H0 8 4Bit WKUP_INT + * H1 8 4Bit WKUP_INT + * H2 8 4Bit WKUP_INT + * H3 8 4Bit WKUP_INT + * I 8 4Bit GPIO_INT15 + * J0 8 4Bit GPIO_INT16 + * J1 5 4Bit GPIO_INT17 + * J2 8 4Bit GPIO_INT18 + * J3 8 4Bit GPIO_INT19 + * J4 4 4Bit GPIO_INT20 + * K0 8 4Bit None + * K1 6 4Bit None + * K2 8 4Bit None + * K3 8 4Bit None + * L0 8 4Bit None + * L1 8 4Bit None + * L2 8 4Bit None + * L3 8 4Bit None + */ + +static struct samsung_gpio_chip s5pc100_gpios_4bit[] = { +#ifdef CONFIG_CPU_S5PC100 + { + .chip = { + .base = S5PC100_GPA0(0), + .ngpio = S5PC100_GPIO_A0_NR, + .label = "GPA0", + }, + }, { + .chip = { + .base = S5PC100_GPA1(0), + .ngpio = S5PC100_GPIO_A1_NR, + .label = "GPA1", + }, + }, { + .chip = { + .base = S5PC100_GPB(0), + .ngpio = S5PC100_GPIO_B_NR, + .label = "GPB", + }, + }, { + .chip = { + .base = S5PC100_GPC(0), + .ngpio = S5PC100_GPIO_C_NR, + .label = "GPC", + }, + }, { + .chip = { + .base = S5PC100_GPD(0), + .ngpio = S5PC100_GPIO_D_NR, + .label = "GPD", + }, + }, { + .chip = { + .base = S5PC100_GPE0(0), + .ngpio = S5PC100_GPIO_E0_NR, + .label = "GPE0", + }, + }, { + .chip = { + .base = S5PC100_GPE1(0), + .ngpio = S5PC100_GPIO_E1_NR, + .label = "GPE1", + }, + }, { + .chip = { + .base = S5PC100_GPF0(0), + .ngpio = S5PC100_GPIO_F0_NR, + .label = "GPF0", + }, + }, { + .chip = { + .base = S5PC100_GPF1(0), + .ngpio = S5PC100_GPIO_F1_NR, + .label = "GPF1", + }, + }, { + .chip = { + .base = S5PC100_GPF2(0), + .ngpio = S5PC100_GPIO_F2_NR, + .label = "GPF2", + }, + }, { + .chip = { + .base = S5PC100_GPF3(0), + .ngpio = S5PC100_GPIO_F3_NR, + .label = "GPF3", + }, + }, { + .chip = { + .base = S5PC100_GPG0(0), + .ngpio = S5PC100_GPIO_G0_NR, + .label = "GPG0", + }, + }, { + .chip = { + .base = S5PC100_GPG1(0), + .ngpio = S5PC100_GPIO_G1_NR, + .label = "GPG1", + }, + }, { + .chip = { + .base = S5PC100_GPG2(0), + .ngpio = S5PC100_GPIO_G2_NR, + .label = "GPG2", + }, + }, { + .chip = { + .base = S5PC100_GPG3(0), + .ngpio = S5PC100_GPIO_G3_NR, + .label = "GPG3", + }, + }, { + .chip = { + .base = S5PC100_GPI(0), + .ngpio = S5PC100_GPIO_I_NR, + .label = "GPI", + }, + }, { + .chip = { + .base = S5PC100_GPJ0(0), + .ngpio = S5PC100_GPIO_J0_NR, + .label = "GPJ0", + }, + }, { + .chip = { + .base = S5PC100_GPJ1(0), + .ngpio = S5PC100_GPIO_J1_NR, + .label = "GPJ1", + }, + }, { + .chip = { + .base = S5PC100_GPJ2(0), + .ngpio = S5PC100_GPIO_J2_NR, + .label = "GPJ2", + }, + }, { + .chip = { + .base = S5PC100_GPJ3(0), + .ngpio = S5PC100_GPIO_J3_NR, + .label = "GPJ3", + }, + }, { + .chip = { + .base = S5PC100_GPJ4(0), + .ngpio = S5PC100_GPIO_J4_NR, + .label = "GPJ4", + }, + }, { + .chip = { + .base = S5PC100_GPK0(0), + .ngpio = S5PC100_GPIO_K0_NR, + .label = "GPK0", + }, + }, { + .chip = { + .base = S5PC100_GPK1(0), + .ngpio = S5PC100_GPIO_K1_NR, + .label = "GPK1", + }, + }, { + .chip = { + .base = S5PC100_GPK2(0), + .ngpio = S5PC100_GPIO_K2_NR, + .label = "GPK2", + }, + }, { + .chip = { + .base = S5PC100_GPK3(0), + .ngpio = S5PC100_GPIO_K3_NR, + .label = "GPK3", + }, + }, { + .chip = { + .base = S5PC100_GPL0(0), + .ngpio = S5PC100_GPIO_L0_NR, + .label = "GPL0", + }, + }, { + .chip = { + .base = S5PC100_GPL1(0), + .ngpio = S5PC100_GPIO_L1_NR, + .label = "GPL1", + }, + }, { + .chip = { + .base = S5PC100_GPL2(0), + .ngpio = S5PC100_GPIO_L2_NR, + .label = "GPL2", + }, + }, { + .chip = { + .base = S5PC100_GPL3(0), + .ngpio = S5PC100_GPIO_L3_NR, + .label = "GPL3", + }, + }, { + .chip = { + .base = S5PC100_GPL4(0), + .ngpio = S5PC100_GPIO_L4_NR, + .label = "GPL4", + }, + }, { + .base = (S5P_VA_GPIO + 0xC00), + .irq_base = IRQ_EINT(0), + .chip = { + .base = S5PC100_GPH0(0), + .ngpio = S5PC100_GPIO_H0_NR, + .label = "GPH0", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO + 0xC20), + .irq_base = IRQ_EINT(8), + .chip = { + .base = S5PC100_GPH1(0), + .ngpio = S5PC100_GPIO_H1_NR, + .label = "GPH1", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO + 0xC40), + .irq_base = IRQ_EINT(16), + .chip = { + .base = S5PC100_GPH2(0), + .ngpio = S5PC100_GPIO_H2_NR, + .label = "GPH2", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO + 0xC60), + .irq_base = IRQ_EINT(24), + .chip = { + .base = S5PC100_GPH3(0), + .ngpio = S5PC100_GPIO_H3_NR, + .label = "GPH3", + .to_irq = samsung_gpiolib_to_irq, + }, + }, +#endif +}; + +/* + * Followings are the gpio banks in S5PV210/S5PC110 + * + * The 'config' member when left to NULL, is initialized to the default + * structure samsung_gpio_cfgs[3] in the init function below. + * + * The 'base' member is also initialized in the init function below. + * Note: The initialization of 'base' member of samsung_gpio_chip structure + * uses the above macro and depends on the banks being listed in order here. + */ + +static struct samsung_gpio_chip s5pv210_gpios_4bit[] = { +#ifdef CONFIG_CPU_S5PV210 + { + .chip = { + .base = S5PV210_GPA0(0), + .ngpio = S5PV210_GPIO_A0_NR, + .label = "GPA0", + }, + }, { + .chip = { + .base = S5PV210_GPA1(0), + .ngpio = S5PV210_GPIO_A1_NR, + .label = "GPA1", + }, + }, { + .chip = { + .base = S5PV210_GPB(0), + .ngpio = S5PV210_GPIO_B_NR, + .label = "GPB", + }, + }, { + .chip = { + .base = S5PV210_GPC0(0), + .ngpio = S5PV210_GPIO_C0_NR, + .label = "GPC0", + }, + }, { + .chip = { + .base = S5PV210_GPC1(0), + .ngpio = S5PV210_GPIO_C1_NR, + .label = "GPC1", + }, + }, { + .chip = { + .base = S5PV210_GPD0(0), + .ngpio = S5PV210_GPIO_D0_NR, + .label = "GPD0", + }, + }, { + .chip = { + .base = S5PV210_GPD1(0), + .ngpio = S5PV210_GPIO_D1_NR, + .label = "GPD1", + }, + }, { + .chip = { + .base = S5PV210_GPE0(0), + .ngpio = S5PV210_GPIO_E0_NR, + .label = "GPE0", + }, + }, { + .chip = { + .base = S5PV210_GPE1(0), + .ngpio = S5PV210_GPIO_E1_NR, + .label = "GPE1", + }, + }, { + .chip = { + .base = S5PV210_GPF0(0), + .ngpio = S5PV210_GPIO_F0_NR, + .label = "GPF0", + }, + }, { + .chip = { + .base = S5PV210_GPF1(0), + .ngpio = S5PV210_GPIO_F1_NR, + .label = "GPF1", + }, + }, { + .chip = { + .base = S5PV210_GPF2(0), + .ngpio = S5PV210_GPIO_F2_NR, + .label = "GPF2", + }, + }, { + .chip = { + .base = S5PV210_GPF3(0), + .ngpio = S5PV210_GPIO_F3_NR, + .label = "GPF3", + }, + }, { + .chip = { + .base = S5PV210_GPG0(0), + .ngpio = S5PV210_GPIO_G0_NR, + .label = "GPG0", + }, + }, { + .chip = { + .base = S5PV210_GPG1(0), + .ngpio = S5PV210_GPIO_G1_NR, + .label = "GPG1", + }, + }, { + .chip = { + .base = S5PV210_GPG2(0), + .ngpio = S5PV210_GPIO_G2_NR, + .label = "GPG2", + }, + }, { + .chip = { + .base = S5PV210_GPG3(0), + .ngpio = S5PV210_GPIO_G3_NR, + .label = "GPG3", + }, + }, { + .chip = { + .base = S5PV210_GPI(0), + .ngpio = S5PV210_GPIO_I_NR, + .label = "GPI", + }, + }, { + .chip = { + .base = S5PV210_GPJ0(0), + .ngpio = S5PV210_GPIO_J0_NR, + .label = "GPJ0", + }, + }, { + .chip = { + .base = S5PV210_GPJ1(0), + .ngpio = S5PV210_GPIO_J1_NR, + .label = "GPJ1", + }, + }, { + .chip = { + .base = S5PV210_GPJ2(0), + .ngpio = S5PV210_GPIO_J2_NR, + .label = "GPJ2", + }, + }, { + .chip = { + .base = S5PV210_GPJ3(0), + .ngpio = S5PV210_GPIO_J3_NR, + .label = "GPJ3", + }, + }, { + .chip = { + .base = S5PV210_GPJ4(0), + .ngpio = S5PV210_GPIO_J4_NR, + .label = "GPJ4", + }, + }, { + .chip = { + .base = S5PV210_MP01(0), + .ngpio = S5PV210_GPIO_MP01_NR, + .label = "MP01", + }, + }, { + .chip = { + .base = S5PV210_MP02(0), + .ngpio = S5PV210_GPIO_MP02_NR, + .label = "MP02", + }, + }, { + .chip = { + .base = S5PV210_MP03(0), + .ngpio = S5PV210_GPIO_MP03_NR, + .label = "MP03", + }, + }, { + .chip = { + .base = S5PV210_MP04(0), + .ngpio = S5PV210_GPIO_MP04_NR, + .label = "MP04", + }, + }, { + .chip = { + .base = S5PV210_MP05(0), + .ngpio = S5PV210_GPIO_MP05_NR, + .label = "MP05", + }, + }, { + .base = (S5P_VA_GPIO + 0xC00), + .irq_base = IRQ_EINT(0), + .chip = { + .base = S5PV210_GPH0(0), + .ngpio = S5PV210_GPIO_H0_NR, + .label = "GPH0", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO + 0xC20), + .irq_base = IRQ_EINT(8), + .chip = { + .base = S5PV210_GPH1(0), + .ngpio = S5PV210_GPIO_H1_NR, + .label = "GPH1", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO + 0xC40), + .irq_base = IRQ_EINT(16), + .chip = { + .base = S5PV210_GPH2(0), + .ngpio = S5PV210_GPIO_H2_NR, + .label = "GPH2", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO + 0xC60), + .irq_base = IRQ_EINT(24), + .chip = { + .base = S5PV210_GPH3(0), + .ngpio = S5PV210_GPIO_H3_NR, + .label = "GPH3", + .to_irq = samsung_gpiolib_to_irq, + }, + }, +#endif +}; + +/* + * Followings are the gpio banks in EXYNOS4210 + * + * The 'config' member when left to NULL, is initialized to the default + * structure samsung_gpio_cfgs[3] in the init function below. + * + * The 'base' member is also initialized in the init function below. + * Note: The initialization of 'base' member of samsung_gpio_chip structure + * uses the above macro and depends on the banks being listed in order here. + */ + +static struct samsung_gpio_chip exynos4_gpios_1[] = { +#ifdef CONFIG_ARCH_EXYNOS4 + { + .chip = { + .base = EXYNOS4_GPA0(0), + .ngpio = EXYNOS4_GPIO_A0_NR, + .label = "GPA0", + }, + }, { + .chip = { + .base = EXYNOS4_GPA1(0), + .ngpio = EXYNOS4_GPIO_A1_NR, + .label = "GPA1", + }, + }, { + .chip = { + .base = EXYNOS4_GPB(0), + .ngpio = EXYNOS4_GPIO_B_NR, + .label = "GPB", + }, + }, { + .chip = { + .base = EXYNOS4_GPC0(0), + .ngpio = EXYNOS4_GPIO_C0_NR, + .label = "GPC0", + }, + }, { + .chip = { + .base = EXYNOS4_GPC1(0), + .ngpio = EXYNOS4_GPIO_C1_NR, + .label = "GPC1", + }, + }, { + .chip = { + .base = EXYNOS4_GPD0(0), + .ngpio = EXYNOS4_GPIO_D0_NR, + .label = "GPD0", + }, + }, { + .chip = { + .base = EXYNOS4_GPD1(0), + .ngpio = EXYNOS4_GPIO_D1_NR, + .label = "GPD1", + }, + }, { + .chip = { + .base = EXYNOS4_GPE0(0), + .ngpio = EXYNOS4_GPIO_E0_NR, + .label = "GPE0", + }, + }, { + .chip = { + .base = EXYNOS4_GPE1(0), + .ngpio = EXYNOS4_GPIO_E1_NR, + .label = "GPE1", + }, + }, { + .chip = { + .base = EXYNOS4_GPE2(0), + .ngpio = EXYNOS4_GPIO_E2_NR, + .label = "GPE2", + }, + }, { + .chip = { + .base = EXYNOS4_GPE3(0), + .ngpio = EXYNOS4_GPIO_E3_NR, + .label = "GPE3", + }, + }, { + .chip = { + .base = EXYNOS4_GPE4(0), + .ngpio = EXYNOS4_GPIO_E4_NR, + .label = "GPE4", + }, + }, { + .chip = { + .base = EXYNOS4_GPF0(0), + .ngpio = EXYNOS4_GPIO_F0_NR, + .label = "GPF0", + }, + }, { + .chip = { + .base = EXYNOS4_GPF1(0), + .ngpio = EXYNOS4_GPIO_F1_NR, + .label = "GPF1", + }, + }, { + .chip = { + .base = EXYNOS4_GPF2(0), + .ngpio = EXYNOS4_GPIO_F2_NR, + .label = "GPF2", + }, + }, { + .chip = { + .base = EXYNOS4_GPF3(0), + .ngpio = EXYNOS4_GPIO_F3_NR, + .label = "GPF3", + }, + }, +#endif +}; + +static struct samsung_gpio_chip exynos4_gpios_2[] = { +#ifdef CONFIG_ARCH_EXYNOS4 + { + .chip = { + .base = EXYNOS4_GPJ0(0), + .ngpio = EXYNOS4_GPIO_J0_NR, + .label = "GPJ0", + }, + }, { + .chip = { + .base = EXYNOS4_GPJ1(0), + .ngpio = EXYNOS4_GPIO_J1_NR, + .label = "GPJ1", + }, + }, { + .chip = { + .base = EXYNOS4_GPK0(0), + .ngpio = EXYNOS4_GPIO_K0_NR, + .label = "GPK0", + }, + }, { + .chip = { + .base = EXYNOS4_GPK1(0), + .ngpio = EXYNOS4_GPIO_K1_NR, + .label = "GPK1", + }, + }, { + .chip = { + .base = EXYNOS4_GPK2(0), + .ngpio = EXYNOS4_GPIO_K2_NR, + .label = "GPK2", + }, + }, { + .chip = { + .base = EXYNOS4_GPK3(0), + .ngpio = EXYNOS4_GPIO_K3_NR, + .label = "GPK3", + }, + }, { + .chip = { + .base = EXYNOS4_GPL0(0), + .ngpio = EXYNOS4_GPIO_L0_NR, + .label = "GPL0", + }, + }, { + .chip = { + .base = EXYNOS4_GPL1(0), + .ngpio = EXYNOS4_GPIO_L1_NR, + .label = "GPL1", + }, + }, { + .chip = { + .base = EXYNOS4_GPL2(0), + .ngpio = EXYNOS4_GPIO_L2_NR, + .label = "GPL2", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = EXYNOS4_GPY0(0), + .ngpio = EXYNOS4_GPIO_Y0_NR, + .label = "GPY0", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = EXYNOS4_GPY1(0), + .ngpio = EXYNOS4_GPIO_Y1_NR, + .label = "GPY1", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = EXYNOS4_GPY2(0), + .ngpio = EXYNOS4_GPIO_Y2_NR, + .label = "GPY2", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = EXYNOS4_GPY3(0), + .ngpio = EXYNOS4_GPIO_Y3_NR, + .label = "GPY3", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = EXYNOS4_GPY4(0), + .ngpio = EXYNOS4_GPIO_Y4_NR, + .label = "GPY4", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = EXYNOS4_GPY5(0), + .ngpio = EXYNOS4_GPIO_Y5_NR, + .label = "GPY5", + }, + }, { + .config = &samsung_gpio_cfgs[0], + .chip = { + .base = EXYNOS4_GPY6(0), + .ngpio = EXYNOS4_GPIO_Y6_NR, + .label = "GPY6", + }, + }, { + .base = (S5P_VA_GPIO2 + 0xC00), + .config = &samsung_gpio_cfgs[3], + .irq_base = IRQ_EINT(0), + .chip = { + .base = EXYNOS4_GPX0(0), + .ngpio = EXYNOS4_GPIO_X0_NR, + .label = "GPX0", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO2 + 0xC20), + .config = &samsung_gpio_cfgs[3], + .irq_base = IRQ_EINT(8), + .chip = { + .base = EXYNOS4_GPX1(0), + .ngpio = EXYNOS4_GPIO_X1_NR, + .label = "GPX1", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO2 + 0xC40), + .config = &samsung_gpio_cfgs[3], + .irq_base = IRQ_EINT(16), + .chip = { + .base = EXYNOS4_GPX2(0), + .ngpio = EXYNOS4_GPIO_X2_NR, + .label = "GPX2", + .to_irq = samsung_gpiolib_to_irq, + }, + }, { + .base = (S5P_VA_GPIO2 + 0xC60), + .config = &samsung_gpio_cfgs[3], + .irq_base = IRQ_EINT(24), + .chip = { + .base = EXYNOS4_GPX3(0), + .ngpio = EXYNOS4_GPIO_X3_NR, + .label = "GPX3", + .to_irq = samsung_gpiolib_to_irq, + }, + }, +#endif +}; + +static struct samsung_gpio_chip exynos4_gpios_3[] = { +#ifdef CONFIG_ARCH_EXYNOS4 + { + .chip = { + .base = EXYNOS4_GPZ(0), + .ngpio = EXYNOS4_GPIO_Z_NR, + .label = "GPZ", + }, + }, +#endif +}; + +/* TODO: cleanup soc_is_* */ +static __init int samsung_gpiolib_init(void) +{ + struct samsung_gpio_chip *chip; + int i, nr_chips; + int group = 0; + + samsung_gpiolib_set_cfg(samsung_gpio_cfgs, ARRAY_SIZE(samsung_gpio_cfgs)); + + if (soc_is_s3c24xx()) { + s3c24xx_gpiolib_add_chips(s3c24xx_gpios, + ARRAY_SIZE(s3c24xx_gpios), S3C24XX_VA_GPIO); + } else if (soc_is_s3c64xx()) { + samsung_gpiolib_add_2bit_chips(s3c64xx_gpios_2bit, + ARRAY_SIZE(s3c64xx_gpios_2bit), + S3C64XX_VA_GPIO + 0xE0, 0x20); + samsung_gpiolib_add_4bit_chips(s3c64xx_gpios_4bit, + ARRAY_SIZE(s3c64xx_gpios_4bit), + S3C64XX_VA_GPIO); + samsung_gpiolib_add_4bit2_chips(s3c64xx_gpios_4bit2, + ARRAY_SIZE(s3c64xx_gpios_4bit2)); + } else if (soc_is_s5p6440()) { + samsung_gpiolib_add_2bit_chips(s5p6440_gpios_2bit, + ARRAY_SIZE(s5p6440_gpios_2bit), NULL, 0x0); + samsung_gpiolib_add_4bit_chips(s5p6440_gpios_4bit, + ARRAY_SIZE(s5p6440_gpios_4bit), S5P_VA_GPIO); + samsung_gpiolib_add_4bit2_chips(s5p6440_gpios_4bit2, + ARRAY_SIZE(s5p6440_gpios_4bit2)); + s5p64x0_gpiolib_add_rbank(s5p6440_gpios_rbank, + ARRAY_SIZE(s5p6440_gpios_rbank)); + } else if (soc_is_s5p6450()) { + samsung_gpiolib_add_2bit_chips(s5p6450_gpios_2bit, + ARRAY_SIZE(s5p6450_gpios_2bit), NULL, 0x0); + samsung_gpiolib_add_4bit_chips(s5p6450_gpios_4bit, + ARRAY_SIZE(s5p6450_gpios_4bit), S5P_VA_GPIO); + samsung_gpiolib_add_4bit2_chips(s5p6450_gpios_4bit2, + ARRAY_SIZE(s5p6450_gpios_4bit2)); + s5p64x0_gpiolib_add_rbank(s5p6450_gpios_rbank, + ARRAY_SIZE(s5p6450_gpios_rbank)); + } else if (soc_is_s5pc100()) { + group = 0; + chip = s5pc100_gpios_4bit; + nr_chips = ARRAY_SIZE(s5pc100_gpios_4bit); + + for (i = 0; i < nr_chips; i++, chip++) { + if (!chip->config) { + chip->config = &samsung_gpio_cfgs[3]; + chip->group = group++; + } + } + samsung_gpiolib_add_4bit_chips(s5pc100_gpios_4bit, nr_chips, S5P_VA_GPIO); +#if defined(CONFIG_CPU_S5PC100) && defined(CONFIG_S5P_GPIO_INT) + s5p_register_gpioint_bank(IRQ_GPIOINT, 0, S5P_GPIOINT_GROUP_MAXNR); +#endif + } else if (soc_is_s5pv210()) { + group = 0; + chip = s5pv210_gpios_4bit; + nr_chips = ARRAY_SIZE(s5pv210_gpios_4bit); + + for (i = 0; i < nr_chips; i++, chip++) { + if (!chip->config) { + chip->config = &samsung_gpio_cfgs[3]; + chip->group = group++; + } + } + samsung_gpiolib_add_4bit_chips(s5pv210_gpios_4bit, nr_chips, S5P_VA_GPIO); +#if defined(CONFIG_CPU_S5PV210) && defined(CONFIG_S5P_GPIO_INT) + s5p_register_gpioint_bank(IRQ_GPIOINT, 0, S5P_GPIOINT_GROUP_MAXNR); +#endif + } else if (soc_is_exynos4210()) { + group = 0; + + /* gpio part1 */ + chip = exynos4_gpios_1; + nr_chips = ARRAY_SIZE(exynos4_gpios_1); + + for (i = 0; i < nr_chips; i++, chip++) { + if (!chip->config) { + chip->config = &exynos4_gpio_cfg; + chip->group = group++; + } + } + samsung_gpiolib_add_4bit_chips(exynos4_gpios_1, nr_chips, S5P_VA_GPIO1); + + /* gpio part2 */ + chip = exynos4_gpios_2; + nr_chips = ARRAY_SIZE(exynos4_gpios_2); + + for (i = 0; i < nr_chips; i++, chip++) { + if (!chip->config) { + chip->config = &exynos4_gpio_cfg; + chip->group = group++; + } + } + samsung_gpiolib_add_4bit_chips(exynos4_gpios_2, nr_chips, S5P_VA_GPIO2); + + /* gpio part3 */ + chip = exynos4_gpios_3; + nr_chips = ARRAY_SIZE(exynos4_gpios_3); + + for (i = 0; i < nr_chips; i++, chip++) { + if (!chip->config) { + chip->config = &exynos4_gpio_cfg; + chip->group = group++; + } + } + samsung_gpiolib_add_4bit_chips(exynos4_gpios_3, nr_chips, S5P_VA_GPIO3); + +#if defined(CONFIG_CPU_EXYNOS4210) && defined(CONFIG_S5P_GPIO_INT) + s5p_register_gpioint_bank(IRQ_GPIO_XA, 0, IRQ_GPIO1_NR_GROUPS); + s5p_register_gpioint_bank(IRQ_GPIO_XB, IRQ_GPIO1_NR_GROUPS, IRQ_GPIO2_NR_GROUPS); +#endif + } + + return 0; +} +core_initcall(samsung_gpiolib_init); + +int s3c_gpio_cfgpin(unsigned int pin, unsigned int config) +{ + struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin); + unsigned long flags; + int offset; + int ret; + + if (!chip) + return -EINVAL; + + offset = pin - chip->chip.base; + + samsung_gpio_lock(chip, flags); + ret = samsung_gpio_do_setcfg(chip, offset, config); + samsung_gpio_unlock(chip, flags); + + return ret; +} +EXPORT_SYMBOL(s3c_gpio_cfgpin); + +int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr, + unsigned int cfg) +{ + int ret; + + for (; nr > 0; nr--, start++) { + ret = s3c_gpio_cfgpin(start, cfg); + if (ret != 0) + return ret; + } + + return 0; +} +EXPORT_SYMBOL_GPL(s3c_gpio_cfgpin_range); + +int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr, + unsigned int cfg, samsung_gpio_pull_t pull) +{ + int ret; + + for (; nr > 0; nr--, start++) { + s3c_gpio_setpull(start, pull); + ret = s3c_gpio_cfgpin(start, cfg); + if (ret != 0) + return ret; + } + + return 0; +} +EXPORT_SYMBOL_GPL(s3c_gpio_cfgall_range); + +unsigned s3c_gpio_getcfg(unsigned int pin) +{ + struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin); + unsigned long flags; + unsigned ret = 0; + int offset; + + if (chip) { + offset = pin - chip->chip.base; + + samsung_gpio_lock(chip, flags); + ret = samsung_gpio_do_getcfg(chip, offset); + samsung_gpio_unlock(chip, flags); + } + + return ret; +} +EXPORT_SYMBOL(s3c_gpio_getcfg); + +int s3c_gpio_setpull(unsigned int pin, samsung_gpio_pull_t pull) +{ + struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin); + unsigned long flags; + int offset, ret; + + if (!chip) + return -EINVAL; + + offset = pin - chip->chip.base; + + samsung_gpio_lock(chip, flags); + ret = samsung_gpio_do_setpull(chip, offset, pull); + samsung_gpio_unlock(chip, flags); + + return ret; +} +EXPORT_SYMBOL(s3c_gpio_setpull); + +samsung_gpio_pull_t s3c_gpio_getpull(unsigned int pin) +{ + struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin); + unsigned long flags; + int offset; + u32 pup = 0; + + if (chip) { + offset = pin - chip->chip.base; + + samsung_gpio_lock(chip, flags); + pup = samsung_gpio_do_getpull(chip, offset); + samsung_gpio_unlock(chip, flags); + } + + return (__force samsung_gpio_pull_t)pup; +} +EXPORT_SYMBOL(s3c_gpio_getpull); + +/* gpiolib wrappers until these are totally eliminated */ + +void s3c2410_gpio_pullup(unsigned int pin, unsigned int to) +{ + int ret; + + WARN_ON(to); /* should be none of these left */ + + if (!to) { + /* if pull is enabled, try first with up, and if that + * fails, try using down */ + + ret = s3c_gpio_setpull(pin, S3C_GPIO_PULL_UP); + if (ret) + s3c_gpio_setpull(pin, S3C_GPIO_PULL_DOWN); + } else { + s3c_gpio_setpull(pin, S3C_GPIO_PULL_NONE); + } +} +EXPORT_SYMBOL(s3c2410_gpio_pullup); + +void s3c2410_gpio_setpin(unsigned int pin, unsigned int to) +{ + /* do this via gpiolib until all users removed */ + + gpio_request(pin, "temporary"); + gpio_set_value(pin, to); + gpio_free(pin); +} +EXPORT_SYMBOL(s3c2410_gpio_setpin); + +unsigned int s3c2410_gpio_getpin(unsigned int pin) +{ + struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin); + unsigned long offs = pin - chip->chip.base; + + return __raw_readl(chip->base + 0x04) & (1 << offs); +} +EXPORT_SYMBOL(s3c2410_gpio_getpin); + +#ifdef CONFIG_S5P_GPIO_DRVSTR +s5p_gpio_drvstr_t s5p_gpio_get_drvstr(unsigned int pin) +{ + struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin); + unsigned int off; + void __iomem *reg; + int shift; + u32 drvstr; + + if (!chip) + return -EINVAL; + + off = pin - chip->chip.base; + shift = off * 2; + reg = chip->base + 0x0C; + + drvstr = __raw_readl(reg); + drvstr = drvstr >> shift; + drvstr &= 0x3; + + return (__force s5p_gpio_drvstr_t)drvstr; +} +EXPORT_SYMBOL(s5p_gpio_get_drvstr); + +int s5p_gpio_set_drvstr(unsigned int pin, s5p_gpio_drvstr_t drvstr) +{ + struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin); + unsigned int off; + void __iomem *reg; + int shift; + u32 tmp; + + if (!chip) + return -EINVAL; + + off = pin - chip->chip.base; + shift = off * 2; + reg = chip->base + 0x0C; + + tmp = __raw_readl(reg); + tmp &= ~(0x3 << shift); + tmp |= drvstr << shift; + + __raw_writel(tmp, reg); + + return 0; +} +EXPORT_SYMBOL(s5p_gpio_set_drvstr); +#endif /* CONFIG_S5P_GPIO_DRVSTR */ + +#ifdef CONFIG_PLAT_S3C24XX +unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change) +{ + unsigned long flags; + unsigned long misccr; + + local_irq_save(flags); + misccr = __raw_readl(S3C24XX_MISCCR); + misccr &= ~clear; + misccr ^= change; + __raw_writel(misccr, S3C24XX_MISCCR); + local_irq_restore(flags); + + return misccr; +} +EXPORT_SYMBOL(s3c2410_modify_misccr); +#endif |