summaryrefslogtreecommitdiffstats
path: root/drivers/gpio
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/gpio')
-rw-r--r--drivers/gpio/Kconfig57
-rw-r--r--drivers/gpio/Makefile6
-rw-r--r--drivers/gpio/cs5535-gpio.c4
-rw-r--r--drivers/gpio/gpiolib.c66
-rw-r--r--drivers/gpio/it8761e_gpio.c231
-rw-r--r--drivers/gpio/max7300.c94
-rw-r--r--drivers/gpio/max7301.c293
-rw-r--r--drivers/gpio/max730x.c244
-rw-r--r--drivers/gpio/pca953x.c249
-rw-r--r--drivers/gpio/pl061.c2
-rw-r--r--drivers/gpio/sch_gpio.c295
-rw-r--r--drivers/gpio/timbgpio.c35
-rw-r--r--drivers/gpio/wm831x-gpio.c45
-rw-r--r--drivers/gpio/wm8350-gpiolib.c181
-rw-r--r--drivers/gpio/wm8994-gpio.c204
15 files changed, 1708 insertions, 298 deletions
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 1f1d88ae68d..fee678f74a1 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -65,8 +65,17 @@ config GPIO_SYSFS
# put expanders in the right section, in alphabetical order
+config GPIO_MAX730X
+ tristate
+
comment "Memory mapped GPIO expanders:"
+config GPIO_IT8761E
+ tristate "IT8761E GPIO support"
+ depends on GPIOLIB
+ help
+ Say yes here to support GPIO functionality of IT8761E super I/O chip.
+
config GPIO_PL061
bool "PrimeCell PL061 GPIO support"
depends on ARM_AMBA
@@ -85,8 +94,32 @@ config GPIO_VR41XX
help
Say yes here to support the NEC VR4100 series General-purpose I/O Uint
+config GPIO_SCH
+ tristate "Intel SCH GPIO"
+ depends on GPIOLIB && PCI
+ select MFD_CORE
+ select LPC_SCH
+ help
+ Say yes here to support GPIO interface on Intel Poulsbo SCH.
+ The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
+ powered by the core power rail and are turned off during sleep
+ modes (S3 and higher). The remaining four GPIOs are powered by
+ the Intel SCH suspend power supply. These GPIOs remain
+ active during S3. The suspend powered GPIOs can be used to wake the
+ system from the Suspend-to-RAM state.
+
+ This driver can also be built as a module. If so, the module
+ will be called sch-gpio.
+
comment "I2C GPIO expanders:"
+config GPIO_MAX7300
+ tristate "Maxim MAX7300 GPIO expander"
+ depends on I2C
+ select GPIO_MAX730X
+ help
+ GPIO driver for Maxim MAX7301 I2C-based GPIO expander.
+
config GPIO_MAX732X
tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
depends on I2C
@@ -124,6 +157,13 @@ config GPIO_PCA953X
This driver can also be built as a module. If so, the module
will be called pca953x.
+config GPIO_PCA953X_IRQ
+ bool "Interrupt controller support for PCA953x"
+ depends on GPIO_PCA953X=y
+ help
+ Say yes here to enable the pca953x to be used as an interrupt
+ controller. It requires the driver to be built in the kernel.
+
config GPIO_PCF857X
tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
depends on I2C
@@ -162,6 +202,20 @@ config GPIO_WM831X
Say yes here to access the GPIO signals of WM831x power management
chips from Wolfson Microelectronics.
+config GPIO_WM8350
+ tristate "WM8350 GPIOs"
+ depends on MFD_WM8350
+ help
+ Say yes here to access the GPIO signals of WM8350 power management
+ chips from Wolfson Microelectronics.
+
+config GPIO_WM8994
+ tristate "WM8994 GPIOs"
+ depends on MFD_WM8994
+ help
+ Say yes here to access the GPIO signals of WM8994 audio hub
+ CODECs from Wolfson Microelectronics.
+
config GPIO_ADP5520
tristate "GPIO Support for ADP5520 PMIC"
depends on PMIC_ADP5520
@@ -226,8 +280,9 @@ comment "SPI GPIO expanders:"
config GPIO_MAX7301
tristate "Maxim MAX7301 GPIO expander"
depends on SPI_MASTER
+ select GPIO_MAX730X
help
- gpio driver for Maxim MAX7301 SPI GPIO expander.
+ GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
config GPIO_MCP23S08
tristate "Microchip MCP23S08 I/O expander"
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 48687238edb..10f3f8d958b 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -7,6 +7,8 @@ obj-$(CONFIG_GPIOLIB) += gpiolib.o
obj-$(CONFIG_GPIO_ADP5520) += adp5520-gpio.o
obj-$(CONFIG_GPIO_ADP5588) += adp5588-gpio.o
obj-$(CONFIG_GPIO_LANGWELL) += langwell_gpio.o
+obj-$(CONFIG_GPIO_MAX730X) += max730x.o
+obj-$(CONFIG_GPIO_MAX7300) += max7300.o
obj-$(CONFIG_GPIO_MAX7301) += max7301.o
obj-$(CONFIG_GPIO_MAX732X) += max732x.o
obj-$(CONFIG_GPIO_MC33880) += mc33880.o
@@ -20,5 +22,9 @@ obj-$(CONFIG_GPIO_UCB1400) += ucb1400_gpio.o
obj-$(CONFIG_GPIO_XILINX) += xilinx_gpio.o
obj-$(CONFIG_GPIO_CS5535) += cs5535-gpio.o
obj-$(CONFIG_GPIO_BT8XX) += bt8xxgpio.o
+obj-$(CONFIG_GPIO_IT8761E) += it8761e_gpio.o
obj-$(CONFIG_GPIO_VR41XX) += vr41xx_giu.o
obj-$(CONFIG_GPIO_WM831X) += wm831x-gpio.o
+obj-$(CONFIG_GPIO_WM8350) += wm8350-gpiolib.o
+obj-$(CONFIG_GPIO_WM8994) += wm8994-gpio.o
+obj-$(CONFIG_GPIO_SCH) += sch_gpio.o \ No newline at end of file
diff --git a/drivers/gpio/cs5535-gpio.c b/drivers/gpio/cs5535-gpio.c
index 0fdbe94f24a..0c3c498f226 100644
--- a/drivers/gpio/cs5535-gpio.c
+++ b/drivers/gpio/cs5535-gpio.c
@@ -154,7 +154,7 @@ static int chip_gpio_request(struct gpio_chip *c, unsigned offset)
static int chip_gpio_get(struct gpio_chip *chip, unsigned offset)
{
- return cs5535_gpio_isset(offset, GPIO_OUTPUT_VAL);
+ return cs5535_gpio_isset(offset, GPIO_READ_BACK);
}
static void chip_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
@@ -172,6 +172,7 @@ static int chip_direction_input(struct gpio_chip *c, unsigned offset)
spin_lock_irqsave(&chip->lock, flags);
__cs5535_gpio_set(chip, offset, GPIO_INPUT_ENABLE);
+ __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_ENABLE);
spin_unlock_irqrestore(&chip->lock, flags);
return 0;
@@ -184,6 +185,7 @@ static int chip_direction_output(struct gpio_chip *c, unsigned offset, int val)
spin_lock_irqsave(&chip->lock, flags);
+ __cs5535_gpio_set(chip, offset, GPIO_INPUT_ENABLE);
__cs5535_gpio_set(chip, offset, GPIO_OUTPUT_ENABLE);
if (val)
__cs5535_gpio_set(chip, offset, GPIO_OUTPUT_VAL);
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 350842ad363..6d1b86661e6 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -623,7 +623,9 @@ static const struct attribute_group gpiochip_attr_group = {
* /sys/class/gpio/unexport ... write-only
* integer N ... number of GPIO to unexport
*/
-static ssize_t export_store(struct class *class, const char *buf, size_t len)
+static ssize_t export_store(struct class *class,
+ struct class_attribute *attr,
+ const char *buf, size_t len)
{
long gpio;
int status;
@@ -653,7 +655,9 @@ done:
return status ? : len;
}
-static ssize_t unexport_store(struct class *class, const char *buf, size_t len)
+static ssize_t unexport_store(struct class *class,
+ struct class_attribute *attr,
+ const char *buf, size_t len)
{
long gpio;
int status;
@@ -1237,6 +1241,64 @@ void gpio_free(unsigned gpio)
}
EXPORT_SYMBOL_GPL(gpio_free);
+/**
+ * gpio_request_one - request a single GPIO with initial configuration
+ * @gpio: the GPIO number
+ * @flags: GPIO configuration as specified by GPIOF_*
+ * @label: a literal description string of this GPIO
+ */
+int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
+{
+ int err;
+
+ err = gpio_request(gpio, label);
+ if (err)
+ return err;
+
+ if (flags & GPIOF_DIR_IN)
+ err = gpio_direction_input(gpio);
+ else
+ err = gpio_direction_output(gpio,
+ (flags & GPIOF_INIT_HIGH) ? 1 : 0);
+
+ return err;
+}
+EXPORT_SYMBOL_GPL(gpio_request_one);
+
+/**
+ * gpio_request_array - request multiple GPIOs in a single call
+ * @array: array of the 'struct gpio'
+ * @num: how many GPIOs in the array
+ */
+int gpio_request_array(struct gpio *array, size_t num)
+{
+ int i, err;
+
+ for (i = 0; i < num; i++, array++) {
+ err = gpio_request_one(array->gpio, array->flags, array->label);
+ if (err)
+ goto err_free;
+ }
+ return 0;
+
+err_free:
+ while (i--)
+ gpio_free((--array)->gpio);
+ return err;
+}
+EXPORT_SYMBOL_GPL(gpio_request_array);
+
+/**
+ * gpio_free_array - release multiple GPIOs in a single call
+ * @array: array of the 'struct gpio'
+ * @num: how many GPIOs in the array
+ */
+void gpio_free_array(struct gpio *array, size_t num)
+{
+ while (num--)
+ gpio_free((array++)->gpio);
+}
+EXPORT_SYMBOL_GPL(gpio_free_array);
/**
* gpiochip_is_requested - return string iff signal was requested
diff --git a/drivers/gpio/it8761e_gpio.c b/drivers/gpio/it8761e_gpio.c
new file mode 100644
index 00000000000..753219cf993
--- /dev/null
+++ b/drivers/gpio/it8761e_gpio.c
@@ -0,0 +1,231 @@
+/*
+ * it8761_gpio.c - GPIO interface for IT8761E Super I/O chip
+ *
+ * Author: Denis Turischev <denis@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+
+#include <linux/gpio.h>
+
+#define SIO_CHIP_ID 0x8761
+#define CHIP_ID_HIGH_BYTE 0x20
+#define CHIP_ID_LOW_BYTE 0x21
+
+static u8 ports[2] = { 0x2e, 0x4e };
+static u8 port;
+
+static DEFINE_SPINLOCK(sio_lock);
+
+#define GPIO_NAME "it8761-gpio"
+#define GPIO_BA_HIGH_BYTE 0x60
+#define GPIO_BA_LOW_BYTE 0x61
+#define GPIO_IOSIZE 4
+#define GPIO1X_IO 0xf0
+#define GPIO2X_IO 0xf1
+
+static u16 gpio_ba;
+
+static u8 read_reg(u8 addr, u8 port)
+{
+ outb(addr, port);
+ return inb(port + 1);
+}
+
+static void write_reg(u8 data, u8 addr, u8 port)
+{
+ outb(addr, port);
+ outb(data, port + 1);
+}
+
+static void enter_conf_mode(u8 port)
+{
+ outb(0x87, port);
+ outb(0x61, port);
+ outb(0x55, port);
+ outb((port == 0x2e) ? 0x55 : 0xaa, port);
+}
+
+static void exit_conf_mode(u8 port)
+{
+ outb(0x2, port);
+ outb(0x2, port + 1);
+}
+
+static void enter_gpio_mode(u8 port)
+{
+ write_reg(0x2, 0x7, port);
+}
+
+static int it8761e_gpio_get(struct gpio_chip *gc, unsigned gpio_num)
+{
+ u16 reg;
+ u8 bit;
+
+ bit = gpio_num % 7;
+ reg = (gpio_num >= 7) ? gpio_ba + 1 : gpio_ba;
+
+ return !!(inb(reg) & (1 << bit));
+}
+
+static int it8761e_gpio_direction_in(struct gpio_chip *gc, unsigned gpio_num)
+{
+ u8 curr_dirs;
+ u8 io_reg, bit;
+
+ bit = gpio_num % 7;
+ io_reg = (gpio_num >= 7) ? GPIO2X_IO : GPIO1X_IO;
+
+ spin_lock(&sio_lock);
+
+ enter_conf_mode(port);
+ enter_gpio_mode(port);
+
+ curr_dirs = read_reg(io_reg, port);
+
+ if (curr_dirs & (1 << bit))
+ write_reg(curr_dirs & ~(1 << bit), io_reg, port);
+
+ exit_conf_mode(port);
+
+ spin_unlock(&sio_lock);
+ return 0;
+}
+
+static void it8761e_gpio_set(struct gpio_chip *gc,
+ unsigned gpio_num, int val)
+{
+ u8 curr_vals, bit;
+ u16 reg;
+
+ bit = gpio_num % 7;
+ reg = (gpio_num >= 7) ? gpio_ba + 1 : gpio_ba;
+
+ spin_lock(&sio_lock);
+
+ curr_vals = inb(reg);
+ if (val)
+ outb(curr_vals | (1 << bit) , reg);
+ else
+ outb(curr_vals & ~(1 << bit), reg);
+
+ spin_unlock(&sio_lock);
+}
+
+static int it8761e_gpio_direction_out(struct gpio_chip *gc,
+ unsigned gpio_num, int val)
+{
+ u8 curr_dirs, io_reg, bit;
+
+ bit = gpio_num % 7;
+ io_reg = (gpio_num >= 7) ? GPIO2X_IO : GPIO1X_IO;
+
+ it8761e_gpio_set(gc, gpio_num, val);
+
+ spin_lock(&sio_lock);
+
+ enter_conf_mode(port);
+ enter_gpio_mode(port);
+
+ curr_dirs = read_reg(io_reg, port);
+
+ if (!(curr_dirs & (1 << bit)))
+ write_reg(curr_dirs | (1 << bit), io_reg, port);
+
+ exit_conf_mode(port);
+
+ spin_unlock(&sio_lock);
+ return 0;
+}
+
+static struct gpio_chip it8761e_gpio_chip = {
+ .label = GPIO_NAME,
+ .owner = THIS_MODULE,
+ .get = it8761e_gpio_get,
+ .direction_input = it8761e_gpio_direction_in,
+ .set = it8761e_gpio_set,
+ .direction_output = it8761e_gpio_direction_out,
+};
+
+static int __init it8761e_gpio_init(void)
+{
+ int i, id, err;
+
+ /* chip and port detection */
+ for (i = 0; i < ARRAY_SIZE(ports); i++) {
+ spin_lock(&sio_lock);
+ enter_conf_mode(ports[i]);
+
+ id = (read_reg(CHIP_ID_HIGH_BYTE, ports[i]) << 8) +
+ read_reg(CHIP_ID_LOW_BYTE, ports[i]);
+
+ exit_conf_mode(ports[i]);
+ spin_unlock(&sio_lock);
+
+ if (id == SIO_CHIP_ID) {
+ port = ports[i];
+ break;
+ }
+ }
+
+ if (!port)
+ return -ENODEV;
+
+ /* fetch GPIO base address */
+ enter_conf_mode(port);
+ enter_gpio_mode(port);
+ gpio_ba = (read_reg(GPIO_BA_HIGH_BYTE, port) << 8) +
+ read_reg(GPIO_BA_LOW_BYTE, port);
+ exit_conf_mode(port);
+
+ if (!request_region(gpio_ba, GPIO_IOSIZE, GPIO_NAME))
+ return -EBUSY;
+
+ it8761e_gpio_chip.base = -1;
+ it8761e_gpio_chip.ngpio = 14;
+
+ err = gpiochip_add(&it8761e_gpio_chip);
+ if (err < 0)
+ goto gpiochip_add_err;
+
+ return 0;
+
+gpiochip_add_err:
+ release_region(gpio_ba, GPIO_IOSIZE);
+ gpio_ba = 0;
+ return err;
+}
+
+static void __exit it8761e_gpio_exit(void)
+{
+ if (gpio_ba) {
+ gpiochip_remove(&it8761e_gpio_chip);
+
+ release_region(gpio_ba, GPIO_IOSIZE);
+ gpio_ba = 0;
+ }
+}
+module_init(it8761e_gpio_init);
+module_exit(it8761e_gpio_exit);
+
+MODULE_AUTHOR("Denis Turischev <denis@compulab.co.il>");
+MODULE_DESCRIPTION("GPIO interface for IT8761E Super I/O chip");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpio/max7300.c b/drivers/gpio/max7300.c
new file mode 100644
index 00000000000..9d74eef1157
--- /dev/null
+++ b/drivers/gpio/max7300.c
@@ -0,0 +1,94 @@
+/*
+ * drivers/gpio/max7300.c
+ *
+ * Copyright (C) 2009 Wolfram Sang, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Check max730x.c for further details.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/i2c.h>
+#include <linux/spi/max7301.h>
+
+static int max7300_i2c_write(struct device *dev, unsigned int reg,
+ unsigned int val)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+
+ return i2c_smbus_write_byte_data(client, reg, val);
+}
+
+static int max7300_i2c_read(struct device *dev, unsigned int reg)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+
+ return i2c_smbus_read_byte_data(client, reg);
+}
+
+static int __devinit max7300_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct max7301 *ts;
+ int ret;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA))
+ return -EIO;
+
+ ts = kzalloc(sizeof(struct max7301), GFP_KERNEL);
+ if (!ts)
+ return -ENOMEM;
+
+ ts->read = max7300_i2c_read;
+ ts->write = max7300_i2c_write;
+ ts->dev = &client->dev;
+
+ ret = __max730x_probe(ts);
+ if (ret)
+ kfree(ts);
+ return ret;
+}
+
+static int __devexit max7300_remove(struct i2c_client *client)
+{
+ return __max730x_remove(&client->dev);
+}
+
+static const struct i2c_device_id max7300_id[] = {
+ { "max7300", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, max7300_id);
+
+static struct i2c_driver max7300_driver = {
+ .driver = {
+ .name = "max7300",
+ .owner = THIS_MODULE,
+ },
+ .probe = max7300_probe,
+ .remove = __devexit_p(max7300_remove),
+ .id_table = max7300_id,
+};
+
+static int __init max7300_init(void)
+{
+ return i2c_add_driver(&max7300_driver);
+}
+subsys_initcall(max7300_init);
+
+static void __exit max7300_exit(void)
+{
+ i2c_del_driver(&max7300_driver);
+}
+module_exit(max7300_exit);
+
+MODULE_AUTHOR("Wolfram Sang");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("MAX7300 GPIO-Expander");
diff --git a/drivers/gpio/max7301.c b/drivers/gpio/max7301.c
index 480956f1ca5..965d9b1ea13 100644
--- a/drivers/gpio/max7301.c
+++ b/drivers/gpio/max7301.c
@@ -1,98 +1,41 @@
-/**
+/*
* drivers/gpio/max7301.c
*
* Copyright (C) 2006 Juergen Beisert, Pengutronix
* Copyright (C) 2008 Guennadi Liakhovetski, Pengutronix
+ * Copyright (C) 2009 Wolfram Sang, Pengutronix
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
- * The Maxim's MAX7301 device is an SPI driven GPIO expander. There are
- * 28 GPIOs. 8 of them can trigger an interrupt. See datasheet for more
- * details
- * Note:
- * - DIN must be stable at the rising edge of clock.
- * - when writing:
- * - always clock in 16 clocks at once
- * - at DIN: D15 first, D0 last
- * - D0..D7 = databyte, D8..D14 = commandbyte
- * - D15 = low -> write command
- * - when reading
- * - always clock in 16 clocks at once
- * - at DIN: D15 first, D0 last
- * - D0..D7 = dummy, D8..D14 = register address
- * - D15 = high -> read command
- * - raise CS and assert it again
- * - always clock in 16 clocks at once
- * - at DOUT: D15 first, D0 last
- * - D0..D7 contains the data from the first cycle
- *
- * The driver exports a standard gpiochip interface
+ * Check max730x.c for further details.
*/
+#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mutex.h>
#include <linux/spi/spi.h>
#include <linux/spi/max7301.h>
-#include <linux/gpio.h>
-
-#define DRIVER_NAME "max7301"
-
-/*
- * Pin configurations, see MAX7301 datasheet page 6
- */
-#define PIN_CONFIG_MASK 0x03
-#define PIN_CONFIG_IN_PULLUP 0x03
-#define PIN_CONFIG_IN_WO_PULLUP 0x02
-#define PIN_CONFIG_OUT 0x01
-
-#define PIN_NUMBER 28
-
-
-/*
- * Some registers must be read back to modify.
- * To save time we cache them here in memory
- */
-struct max7301 {
- struct mutex lock;
- u8 port_config[8]; /* field 0 is unused */
- u32 out_level; /* cached output levels */
- struct gpio_chip chip;
- struct spi_device *spi;
-};
-/**
- * max7301_write - Write a new register content
- * @spi: The SPI device
- * @reg: Register offset
- * @val: Value to write
- *
- * A write to the MAX7301 means one message with one transfer
- *
- * Returns 0 if successful or a negative value on error
- */
-static int max7301_write(struct spi_device *spi, unsigned int reg, unsigned int val)
+/* A write to the MAX7301 means one message with one transfer */
+static int max7301_spi_write(struct device *dev, unsigned int reg,
+ unsigned int val)
{
+ struct spi_device *spi = to_spi_device(dev);
u16 word = ((reg & 0x7F) << 8) | (val & 0xFF);
+
return spi_write(spi, (const u8 *)&word, sizeof(word));
}
-/**
- * max7301_read - Read back register content
- * @spi: The SPI device
- * @reg: Register offset
- *
- * A read from the MAX7301 means two transfers; here, one message each
- *
- * Returns positive 8 bit value from device if successful or a
- * negative value on error
- */
-static int max7301_read(struct spi_device *spi, unsigned int reg)
+/* A read from the MAX7301 means two transfers; here, one message each */
+
+static int max7301_spi_read(struct device *dev, unsigned int reg)
{
int ret;
u16 word;
+ struct spi_device *spi = to_spi_device(dev);
word = 0x8000 | (reg << 8);
ret = spi_write(spi, (const u8 *)&word, sizeof(word));
@@ -108,125 +51,13 @@ static int max7301_read(struct spi_device *spi, unsigned int reg)
return word & 0xff;
}
-static int max7301_direction_input(struct gpio_chip *chip, unsigned offset)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
- u8 *config;
- int ret;
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- config = &ts->port_config[offset >> 2];
-
- mutex_lock(&ts->lock);
-
- /* Standard GPIO API doesn't support pull-ups, has to be extended.
- * Hard-coding no pollup for now. */
- *config = (*config & ~(3 << (offset & 3))) | (1 << (offset & 3));
-
- ret = max7301_write(ts->spi, 0x08 + (offset >> 2), *config);
-
- mutex_unlock(&ts->lock);
-
- return ret;
-}
-
-static int __max7301_set(struct max7301 *ts, unsigned offset, int value)
-{
- if (value) {
- ts->out_level |= 1 << offset;
- return max7301_write(ts->spi, 0x20 + offset, 0x01);
- } else {
- ts->out_level &= ~(1 << offset);
- return max7301_write(ts->spi, 0x20 + offset, 0x00);
- }
-}
-
-static int max7301_direction_output(struct gpio_chip *chip, unsigned offset,
- int value)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
- u8 *config;
- int ret;
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- config = &ts->port_config[offset >> 2];
-
- mutex_lock(&ts->lock);
-
- *config = (*config & ~(3 << (offset & 3))) | (1 << (offset & 3));
-
- ret = __max7301_set(ts, offset, value);
-
- if (!ret)
- ret = max7301_write(ts->spi, 0x08 + (offset >> 2), *config);
-
- mutex_unlock(&ts->lock);
-
- return ret;
-}
-
-static int max7301_get(struct gpio_chip *chip, unsigned offset)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
- int config, level = -EINVAL;
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- mutex_lock(&ts->lock);
-
- config = (ts->port_config[offset >> 2] >> ((offset & 3) * 2)) & 3;
-
- switch (config) {
- case 1:
- /* Output: return cached level */
- level = !!(ts->out_level & (1 << offset));
- break;
- case 2:
- case 3:
- /* Input: read out */
- level = max7301_read(ts->spi, 0x20 + offset) & 0x01;
- }
- mutex_unlock(&ts->lock);
-
- return level;
-}
-
-static void max7301_set(struct gpio_chip *chip, unsigned offset, int value)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- mutex_lock(&ts->lock);
-
- __max7301_set(ts, offset, value);
-
- mutex_unlock(&ts->lock);
-}
-
static int __devinit max7301_probe(struct spi_device *spi)
{
struct max7301 *ts;
- struct max7301_platform_data *pdata;
- int i, ret;
-
- pdata = spi->dev.platform_data;
- if (!pdata || !pdata->base) {
- dev_dbg(&spi->dev, "incorrect or missing platform data\n");
- return -EINVAL;
- }
+ int ret;
- /*
- * bits_per_word cannot be configured in platform data
- */
+ /* bits_per_word cannot be configured in platform data */
spi->bits_per_word = 16;
-
ret = spi_setup(spi);
if (ret < 0)
return ret;
@@ -235,90 +66,35 @@ static int __devinit max7301_probe(struct spi_device *spi)
if (!ts)
return -ENOMEM;
- mutex_init(&ts->lock);
-
- dev_set_drvdata(&spi->dev, ts);
+ ts->read = max7301_spi_read;
+ ts->write = max7301_spi_write;
+ ts->dev = &spi->dev;
- /* Power up the chip and disable IRQ output */
- max7301_write(spi, 0x04, 0x01);
-
- ts->spi = spi;
-
- ts->chip.label = DRIVER_NAME,
-
- ts->chip.direction_input = max7301_direction_input;
- ts->chip.get = max7301_get;
- ts->chip.direction_output = max7301_direction_output;
- ts->chip.set = max7301_set;
-
- ts->chip.base = pdata->base;
- ts->chip.ngpio = PIN_NUMBER;
- ts->chip.can_sleep = 1;
- ts->chip.dev = &spi->dev;
- ts->chip.owner = THIS_MODULE;
-
- /*
- * tristate all pins in hardware and cache the
- * register values for later use.
- */
- for (i = 1; i < 8; i++) {
- int j;
- /* 0xAA means input with internal pullup disabled */
- max7301_write(spi, 0x08 + i, 0xAA);
- ts->port_config[i] = 0xAA;
- for (j = 0; j < 4; j++) {
- int offset = (i - 1) * 4 + j;
- ret = max7301_direction_input(&ts->chip, offset);
- if (ret)
- goto exit_destroy;
- }
- }
-
- ret = gpiochip_add(&ts->chip);
+ ret = __max730x_probe(ts);
if (ret)
- goto exit_destroy;
-
- return ret;
-
-exit_destroy:
- dev_set_drvdata(&spi->dev, NULL);
- mutex_destroy(&ts->lock);
- kfree(ts);
+ kfree(ts);
return ret;
}
static int __devexit max7301_remove(struct spi_device *spi)
{
- struct max7301 *ts;
- int ret;
-
- ts = dev_get_drvdata(&spi->dev);
- if (ts == NULL)
- return -ENODEV;
-
- dev_set_drvdata(&spi->dev, NULL);
-
- /* Power down the chip and disable IRQ output */
- max7301_write(spi, 0x04, 0x00);
-
- ret = gpiochip_remove(&ts->chip);
- if (!ret) {
- mutex_destroy(&ts->lock);
- kfree(ts);
- } else
- dev_err(&spi->dev, "Failed to remove the GPIO controller: %d\n",
- ret);
-
- return ret;
+ return __max730x_remove(&spi->dev);
}
+static const struct spi_device_id max7301_id[] = {
+ { "max7301", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, max7301_id);
+
static struct spi_driver max7301_driver = {
.driver = {
- .name = DRIVER_NAME,
- .owner = THIS_MODULE,
+ .name = "max7301",
+ .owner = THIS_MODULE,
},
- .probe = max7301_probe,
- .remove = __devexit_p(max7301_remove),
+ .probe = max7301_probe,
+ .remove = __devexit_p(max7301_remove),
+ .id_table = max7301_id,
};
static int __init max7301_init(void)
@@ -336,7 +112,6 @@ static void __exit max7301_exit(void)
}
module_exit(max7301_exit);
-MODULE_AUTHOR("Juergen Beisert");
+MODULE_AUTHOR("Juergen Beisert, Wolfram Sang");
MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("MAX7301 SPI based GPIO-Expander");
-MODULE_ALIAS("spi:" DRIVER_NAME);
+MODULE_DESCRIPTION("MAX7301 GPIO-Expander");
diff --git a/drivers/gpio/max730x.c b/drivers/gpio/max730x.c
new file mode 100644
index 00000000000..c9bced55f82
--- /dev/null
+++ b/drivers/gpio/max730x.c
@@ -0,0 +1,244 @@
+/**
+ * drivers/gpio/max7301.c
+ *
+ * Copyright (C) 2006 Juergen Beisert, Pengutronix
+ * Copyright (C) 2008 Guennadi Liakhovetski, Pengutronix
+ * Copyright (C) 2009 Wolfram Sang, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * The Maxim MAX7300/1 device is an I2C/SPI driven GPIO expander. There are
+ * 28 GPIOs. 8 of them can trigger an interrupt. See datasheet for more
+ * details
+ * Note:
+ * - DIN must be stable at the rising edge of clock.
+ * - when writing:
+ * - always clock in 16 clocks at once
+ * - at DIN: D15 first, D0 last
+ * - D0..D7 = databyte, D8..D14 = commandbyte
+ * - D15 = low -> write command
+ * - when reading
+ * - always clock in 16 clocks at once
+ * - at DIN: D15 first, D0 last
+ * - D0..D7 = dummy, D8..D14 = register address
+ * - D15 = high -> read command
+ * - raise CS and assert it again
+ * - always clock in 16 clocks at once
+ * - at DOUT: D15 first, D0 last
+ * - D0..D7 contains the data from the first cycle
+ *
+ * The driver exports a standard gpiochip interface
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/spi/max7301.h>
+#include <linux/gpio.h>
+
+/*
+ * Pin configurations, see MAX7301 datasheet page 6
+ */
+#define PIN_CONFIG_MASK 0x03
+#define PIN_CONFIG_IN_PULLUP 0x03
+#define PIN_CONFIG_IN_WO_PULLUP 0x02
+#define PIN_CONFIG_OUT 0x01
+
+#define PIN_NUMBER 28
+
+static int max7301_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ struct max7301 *ts = container_of(chip, struct max7301, chip);
+ u8 *config;
+ u8 offset_bits;
+ int ret;
+
+ /* First 4 pins are unused in the controller */
+ offset += 4;
+ offset_bits = (offset & 3) << 1;
+
+ config = &ts->port_config[offset >> 2];
+
+ mutex_lock(&ts->lock);
+
+ /* Standard GPIO API doesn't support pull-ups, has to be extended.
+ * Hard-coding no pollup for now. */
+ *config = (*config & ~(PIN_CONFIG_MASK << offset_bits))
+ | (PIN_CONFIG_IN_WO_PULLUP << offset_bits);
+
+ ret = ts->write(ts->dev, 0x08 + (offset >> 2), *config);
+
+ mutex_unlock(&ts->lock);
+
+ return ret;
+}
+
+static int __max7301_set(struct max7301 *ts, unsigned offset, int value)
+{
+ if (value) {
+ ts->out_level |= 1 << offset;
+ return ts->write(ts->dev, 0x20 + offset, 0x01);
+ } else {
+ ts->out_level &= ~(1 << offset);
+ return ts->write(ts->dev, 0x20 + offset, 0x00);
+ }
+}
+
+static int max7301_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ struct max7301 *ts = container_of(chip, struct max7301, chip);
+ u8 *config;
+ u8 offset_bits;
+ int ret;
+
+ /* First 4 pins are unused in the controller */
+ offset += 4;
+ offset_bits = (offset & 3) << 1;
+
+ config = &ts->port_config[offset >> 2];
+
+ mutex_lock(&ts->lock);
+
+ *config = (*config & ~(PIN_CONFIG_MASK << offset_bits))
+ | (PIN_CONFIG_OUT << offset_bits);
+
+ ret = __max7301_set(ts, offset, value);
+
+ if (!ret)
+ ret = ts->write(ts->dev, 0x08 + (offset >> 2), *config);
+
+ mutex_unlock(&ts->lock);
+
+ return ret;
+}
+
+static int max7301_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct max7301 *ts = container_of(chip, struct max7301, chip);
+ int config, level = -EINVAL;
+
+ /* First 4 pins are unused in the controller */
+ offset += 4;
+
+ mutex_lock(&ts->lock);
+
+ config = (ts->port_config[offset >> 2] >> ((offset & 3) << 1))
+ & PIN_CONFIG_MASK;
+
+ switch (config) {
+ case PIN_CONFIG_OUT:
+ /* Output: return cached level */
+ level = !!(ts->out_level & (1 << offset));
+ break;
+ case PIN_CONFIG_IN_WO_PULLUP:
+ case PIN_CONFIG_IN_PULLUP:
+ /* Input: read out */
+ level = ts->read(ts->dev, 0x20 + offset) & 0x01;
+ }
+ mutex_unlock(&ts->lock);
+
+ return level;
+}
+
+static void max7301_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct max7301 *ts = container_of(chip, struct max7301, chip);
+
+ /* First 4 pins are unused in the controller */
+ offset += 4;
+
+ mutex_lock(&ts->lock);
+
+ __max7301_set(ts, offset, value);
+
+ mutex_unlock(&ts->lock);
+}
+
+int __devinit __max730x_probe(struct max7301 *ts)
+{
+ struct device *dev = ts->dev;
+ struct max7301_platform_data *pdata;
+ int i, ret;
+
+ pdata = dev->platform_data;
+ if (!pdata || !pdata->base) {
+ dev_err(dev, "incorrect or missing platform data\n");
+ return -EINVAL;
+ }
+
+ mutex_init(&ts->lock);
+ dev_set_drvdata(dev, ts);
+
+ /* Power up the chip and disable IRQ output */
+ ts->write(dev, 0x04, 0x01);
+
+ ts->chip.label = dev->driver->name;
+
+ ts->chip.direction_input = max7301_direction_input;
+ ts->chip.get = max7301_get;
+ ts->chip.direction_output = max7301_direction_output;
+ ts->chip.set = max7301_set;
+
+ ts->chip.base = pdata->base;
+ ts->chip.ngpio = PIN_NUMBER;
+ ts->chip.can_sleep = 1;
+ ts->chip.dev = dev;
+ ts->chip.owner = THIS_MODULE;
+
+ /*
+ * tristate all pins in hardware and cache the
+ * register values for later use.
+ */
+ for (i = 1; i < 8; i++) {
+ int j;
+ /* 0xAA means input with internal pullup disabled */
+ ts->write(dev, 0x08 + i, 0xAA);
+ ts->port_config[i] = 0xAA;
+ for (j = 0; j < 4; j++) {
+ int offset = (i - 1) * 4 + j;
+ ret = max7301_direction_input(&ts->chip, offset);
+ if (ret)
+ goto exit_destroy;
+ }
+ }
+
+ ret = gpiochip_add(&ts->chip);
+ if (ret)
+ goto exit_destroy;
+
+ return ret;
+
+exit_destroy:
+ dev_set_drvdata(dev, NULL);
+ mutex_destroy(&ts->lock);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(__max730x_probe);
+
+int __devexit __max730x_remove(struct device *dev)
+{
+ struct max7301 *ts = dev_get_drvdata(dev);
+ int ret;
+
+ if (ts == NULL)
+ return -ENODEV;
+
+ dev_set_drvdata(dev, NULL);
+
+ /* Power down the chip and disable IRQ output */
+ ts->write(dev, 0x04, 0x00);
+
+ ret = gpiochip_remove(&ts->chip);
+ if (!ret) {
+ mutex_destroy(&ts->lock);
+ kfree(ts);
+ } else
+ dev_err(dev, "Failed to remove GPIO controller: %d\n", ret);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(__max730x_remove);
diff --git a/drivers/gpio/pca953x.c b/drivers/gpio/pca953x.c
index 6a2fb3fbb3d..ab5daab14bc 100644
--- a/drivers/gpio/pca953x.c
+++ b/drivers/gpio/pca953x.c
@@ -14,6 +14,8 @@
#include <linux/module.h>
#include <linux/init.h>
#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
#include <linux/i2c.h>
#include <linux/i2c/pca953x.h>
#ifdef CONFIG_OF_GPIO
@@ -26,23 +28,28 @@
#define PCA953X_INVERT 2
#define PCA953X_DIRECTION 3
+#define PCA953X_GPIOS 0x00FF
+#define PCA953X_INT 0x0100
+
static const struct i2c_device_id pca953x_id[] = {
- { "pca9534", 8, },
- { "pca9535", 16, },
+ { "pca9534", 8 | PCA953X_INT, },
+ { "pca9535", 16 | PCA953X_INT, },
{ "pca9536", 4, },
- { "pca9537", 4, },
- { "pca9538", 8, },
- { "pca9539", 16, },
- { "pca9554", 8, },
- { "pca9555", 16, },
+ { "pca9537", 4 | PCA953X_INT, },
+ { "pca9538", 8 | PCA953X_INT, },
+ { "pca9539", 16 | PCA953X_INT, },
+ { "pca9554", 8 | PCA953X_INT, },
+ { "pca9555", 16 | PCA953X_INT, },
{ "pca9556", 8, },
{ "pca9557", 8, },
{ "max7310", 8, },
- { "max7315", 8, },
- { "pca6107", 8, },
- { "tca6408", 8, },
- { "tca6416", 16, },
+ { "max7312", 16 | PCA953X_INT, },
+ { "max7313", 16 | PCA953X_INT, },
+ { "max7315", 8 | PCA953X_INT, },
+ { "pca6107", 8 | PCA953X_INT, },
+ { "tca6408", 8 | PCA953X_INT, },
+ { "tca6416", 16 | PCA953X_INT, },
/* NYET: { "tca6424", 24, }, */
{ }
};
@@ -53,6 +60,15 @@ struct pca953x_chip {
uint16_t reg_output;
uint16_t reg_direction;
+#ifdef CONFIG_GPIO_PCA953X_IRQ
+ struct mutex irq_lock;
+ uint16_t irq_mask;
+ uint16_t irq_stat;
+ uint16_t irq_trig_raise;
+ uint16_t irq_trig_fall;
+ int irq_base;
+#endif
+
struct i2c_client *client;
struct pca953x_platform_data *dyn_pdata;
struct gpio_chip gpio_chip;
@@ -202,6 +218,210 @@ static void pca953x_setup_gpio(struct pca953x_chip *chip, int gpios)
gc->names = chip->names;
}
+#ifdef CONFIG_GPIO_PCA953X_IRQ
+static int pca953x_gpio_to_irq(struct gpio_chip *gc, unsigned off)
+{
+ struct pca953x_chip *chip;
+
+ chip = container_of(gc, struct pca953x_chip, gpio_chip);
+ return chip->irq_base + off;
+}
+
+static void pca953x_irq_mask(unsigned int irq)
+{
+ struct pca953x_chip *chip = get_irq_chip_data(irq);
+
+ chip->irq_mask &= ~(1 << (irq - chip->irq_base));
+}
+
+static void pca953x_irq_unmask(unsigned int irq)
+{
+ struct pca953x_chip *chip = get_irq_chip_data(irq);
+
+ chip->irq_mask |= 1 << (irq - chip->irq_base);
+}
+
+static void pca953x_irq_bus_lock(unsigned int irq)
+{
+ struct pca953x_chip *chip = get_irq_chip_data(irq);
+
+ mutex_lock(&chip->irq_lock);
+}
+
+static void pca953x_irq_bus_sync_unlock(unsigned int irq)
+{
+ struct pca953x_chip *chip = get_irq_chip_data(irq);
+
+ mutex_unlock(&chip->irq_lock);
+}
+
+static int pca953x_irq_set_type(unsigned int irq, unsigned int type)
+{
+ struct pca953x_chip *chip = get_irq_chip_data(irq);
+ uint16_t level = irq - chip->irq_base;
+ uint16_t mask = 1 << level;
+
+ if (!(type & IRQ_TYPE_EDGE_BOTH)) {
+ dev_err(&chip->client->dev, "irq %d: unsupported type %d\n",
+ irq, type);
+ return -EINVAL;
+ }
+
+ if (type & IRQ_TYPE_EDGE_FALLING)
+ chip->irq_trig_fall |= mask;
+ else
+ chip->irq_trig_fall &= ~mask;
+
+ if (type & IRQ_TYPE_EDGE_RISING)
+ chip->irq_trig_raise |= mask;
+ else
+ chip->irq_trig_raise &= ~mask;
+
+ return pca953x_gpio_direction_input(&chip->gpio_chip, level);
+}
+
+static struct irq_chip pca953x_irq_chip = {
+ .name = "pca953x",
+ .mask = pca953x_irq_mask,
+ .unmask = pca953x_irq_unmask,
+ .bus_lock = pca953x_irq_bus_lock,
+ .bus_sync_unlock = pca953x_irq_bus_sync_unlock,
+ .set_type = pca953x_irq_set_type,
+};
+
+static uint16_t pca953x_irq_pending(struct pca953x_chip *chip)
+{
+ uint16_t cur_stat;
+ uint16_t old_stat;
+ uint16_t pending;
+ uint16_t trigger;
+ int ret;
+
+ ret = pca953x_read_reg(chip, PCA953X_INPUT, &cur_stat);
+ if (ret)
+ return 0;
+
+ /* Remove output pins from the equation */
+ cur_stat &= chip->reg_direction;
+
+ old_stat = chip->irq_stat;
+ trigger = (cur_stat ^ old_stat) & chip->irq_mask;
+
+ if (!trigger)
+ return 0;
+
+ chip->irq_stat = cur_stat;
+
+ pending = (old_stat & chip->irq_trig_fall) |
+ (cur_stat & chip->irq_trig_raise);
+ pending &= trigger;
+
+ return pending;
+}
+
+static irqreturn_t pca953x_irq_handler(int irq, void *devid)
+{
+ struct pca953x_chip *chip = devid;
+ uint16_t pending;
+ uint16_t level;
+
+ pending = pca953x_irq_pending(chip);
+
+ if (!pending)
+ return IRQ_HANDLED;
+
+ do {
+ level = __ffs(pending);
+ handle_nested_irq(level + chip->irq_base);
+
+ pending &= ~(1 << level);
+ } while (pending);
+
+ return IRQ_HANDLED;
+}
+
+static int pca953x_irq_setup(struct pca953x_chip *chip,
+ const struct i2c_device_id *id)
+{
+ struct i2c_client *client = chip->client;
+ struct pca953x_platform_data *pdata = client->dev.platform_data;
+ int ret;
+
+ if (pdata->irq_base && (id->driver_data & PCA953X_INT)) {
+ int lvl;
+
+ ret = pca953x_read_reg(chip, PCA953X_INPUT,
+ &chip->irq_stat);
+ if (ret)
+ goto out_failed;
+
+ /*
+ * There is no way to know which GPIO line generated the
+ * interrupt. We have to rely on the previous read for
+ * this purpose.
+ */
+ chip->irq_stat &= chip->reg_direction;
+ chip->irq_base = pdata->irq_base;
+ mutex_init(&chip->irq_lock);
+
+ for (lvl = 0; lvl < chip->gpio_chip.ngpio; lvl++) {
+ int irq = lvl + chip->irq_base;
+
+ set_irq_chip_data(irq, chip);
+ set_irq_chip_and_handler(irq, &pca953x_irq_chip,
+ handle_edge_irq);
+ set_irq_nested_thread(irq, 1);
+#ifdef CONFIG_ARM
+ set_irq_flags(irq, IRQF_VALID);
+#else
+ set_irq_noprobe(irq);
+#endif
+ }
+
+ ret = request_threaded_irq(client->irq,
+ NULL,
+ pca953x_irq_handler,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ dev_name(&client->dev), chip);
+ if (ret) {
+ dev_err(&client->dev, "failed to request irq %d\n",
+ client->irq);
+ goto out_failed;
+ }
+
+ chip->gpio_chip.to_irq = pca953x_gpio_to_irq;
+ }
+
+ return 0;
+
+out_failed:
+ chip->irq_base = 0;
+ return ret;
+}
+
+static void pca953x_irq_teardown(struct pca953x_chip *chip)
+{
+ if (chip->irq_base)
+ free_irq(chip->client->irq, chip);
+}
+#else /* CONFIG_GPIO_PCA953X_IRQ */
+static int pca953x_irq_setup(struct pca953x_chip *chip,
+ const struct i2c_device_id *id)
+{
+ struct i2c_client *client = chip->client;
+ struct pca953x_platform_data *pdata = client->dev.platform_data;
+
+ if (pdata->irq_base && (id->driver_data & PCA953X_INT))
+ dev_warn(&client->dev, "interrupt support not compiled in\n");
+
+ return 0;
+}
+
+static void pca953x_irq_teardown(struct pca953x_chip *chip)
+{
+}
+#endif
+
/*
* Handlers for alternative sources of platform_data
*/
@@ -286,7 +506,7 @@ static int __devinit pca953x_probe(struct i2c_client *client,
/* initialize cached registers from their original values.
* we can't share this chip with another i2c master.
*/
- pca953x_setup_gpio(chip, id->driver_data);
+ pca953x_setup_gpio(chip, id->driver_data & PCA953X_GPIOS);
ret = pca953x_read_reg(chip, PCA953X_OUTPUT, &chip->reg_output);
if (ret)
@@ -301,6 +521,9 @@ static int __devinit pca953x_probe(struct i2c_client *client,
if (ret)
goto out_failed;
+ ret = pca953x_irq_setup(chip, id);
+ if (ret)
+ goto out_failed;
ret = gpiochip_add(&chip->gpio_chip);
if (ret)
@@ -317,6 +540,7 @@ static int __devinit pca953x_probe(struct i2c_client *client,
return 0;
out_failed:
+ pca953x_irq_teardown(chip);
kfree(chip->dyn_pdata);
kfree(chip);
return ret;
@@ -345,6 +569,7 @@ static int pca953x_remove(struct i2c_client *client)
return ret;
}
+ pca953x_irq_teardown(chip);
kfree(chip->dyn_pdata);
kfree(chip);
return 0;
diff --git a/drivers/gpio/pl061.c b/drivers/gpio/pl061.c
index 4ee4c8367a3..3ad1eeb4960 100644
--- a/drivers/gpio/pl061.c
+++ b/drivers/gpio/pl061.c
@@ -219,7 +219,7 @@ static void pl061_irq_handler(unsigned irq, struct irq_desc *desc)
if (pending == 0)
continue;
- for_each_bit(offset, &pending, PL061_GPIO_NR)
+ for_each_set_bit(offset, &pending, PL061_GPIO_NR)
generic_handle_irq(pl061_to_irq(&chip->gc, offset));
}
desc->chip->unmask(irq);
diff --git a/drivers/gpio/sch_gpio.c b/drivers/gpio/sch_gpio.c
new file mode 100644
index 00000000000..583521352c1
--- /dev/null
+++ b/drivers/gpio/sch_gpio.c
@@ -0,0 +1,295 @@
+/*
+ * sch_gpio.c - GPIO interface for Intel Poulsbo SCH
+ *
+ * Copyright (c) 2010 CompuLab Ltd
+ * Author: Denis Turischev <denis@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING. If not, write to
+ * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/errno.h>
+#include <linux/acpi.h>
+#include <linux/platform_device.h>
+
+#include <linux/gpio.h>
+
+static DEFINE_SPINLOCK(gpio_lock);
+
+#define CGEN (0x00)
+#define CGIO (0x04)
+#define CGLV (0x08)
+
+#define RGEN (0x20)
+#define RGIO (0x24)
+#define RGLV (0x28)
+
+static unsigned short gpio_ba;
+
+static int sch_gpio_core_direction_in(struct gpio_chip *gc, unsigned gpio_num)
+{
+ u8 curr_dirs;
+ unsigned short offset, bit;
+
+ spin_lock(&gpio_lock);
+
+ offset = CGIO + gpio_num / 8;
+ bit = gpio_num % 8;
+
+ curr_dirs = inb(gpio_ba + offset);
+
+ if (!(curr_dirs & (1 << bit)))
+ outb(curr_dirs | (1 << bit), gpio_ba + offset);
+
+ spin_unlock(&gpio_lock);
+ return 0;
+}
+
+static int sch_gpio_core_get(struct gpio_chip *gc, unsigned gpio_num)
+{
+ int res;
+ unsigned short offset, bit;
+
+ offset = CGLV + gpio_num / 8;
+ bit = gpio_num % 8;
+
+ res = !!(inb(gpio_ba + offset) & (1 << bit));
+ return res;
+}
+
+static void sch_gpio_core_set(struct gpio_chip *gc, unsigned gpio_num, int val)
+{
+ u8 curr_vals;
+ unsigned short offset, bit;
+
+ spin_lock(&gpio_lock);
+
+ offset = CGLV + gpio_num / 8;
+ bit = gpio_num % 8;
+
+ curr_vals = inb(gpio_ba + offset);
+
+ if (val)
+ outb(curr_vals | (1 << bit), gpio_ba + offset);
+ else
+ outb((curr_vals & ~(1 << bit)), gpio_ba + offset);
+ spin_unlock(&gpio_lock);
+}
+
+static int sch_gpio_core_direction_out(struct gpio_chip *gc,
+ unsigned gpio_num, int val)
+{
+ u8 curr_dirs;
+ unsigned short offset, bit;
+
+ sch_gpio_core_set(gc, gpio_num, val);
+
+ spin_lock(&gpio_lock);
+
+ offset = CGIO + gpio_num / 8;
+ bit = gpio_num % 8;
+
+ curr_dirs = inb(gpio_ba + offset);
+ if (curr_dirs & (1 << bit))
+ outb(curr_dirs & ~(1 << bit), gpio_ba + offset);
+
+ spin_unlock(&gpio_lock);
+ return 0;
+}
+
+static struct gpio_chip sch_gpio_core = {
+ .label = "sch_gpio_core",
+ .owner = THIS_MODULE,
+ .direction_input = sch_gpio_core_direction_in,
+ .get = sch_gpio_core_get,
+ .direction_output = sch_gpio_core_direction_out,
+ .set = sch_gpio_core_set,
+};
+
+static int sch_gpio_resume_direction_in(struct gpio_chip *gc,
+ unsigned gpio_num)
+{
+ u8 curr_dirs;
+
+ spin_lock(&gpio_lock);
+
+ curr_dirs = inb(gpio_ba + RGIO);
+
+ if (!(curr_dirs & (1 << gpio_num)))
+ outb(curr_dirs | (1 << gpio_num) , gpio_ba + RGIO);
+
+ spin_unlock(&gpio_lock);
+ return 0;
+}
+
+static int sch_gpio_resume_get(struct gpio_chip *gc, unsigned gpio_num)
+{
+ return !!(inb(gpio_ba + RGLV) & (1 << gpio_num));
+}
+
+static void sch_gpio_resume_set(struct gpio_chip *gc,
+ unsigned gpio_num, int val)
+{
+ u8 curr_vals;
+
+ spin_lock(&gpio_lock);
+
+ curr_vals = inb(gpio_ba + RGLV);
+
+ if (val)
+ outb(curr_vals | (1 << gpio_num), gpio_ba + RGLV);
+ else
+ outb((curr_vals & ~(1 << gpio_num)), gpio_ba + RGLV);
+
+ spin_unlock(&gpio_lock);
+}
+
+static int sch_gpio_resume_direction_out(struct gpio_chip *gc,
+ unsigned gpio_num, int val)
+{
+ u8 curr_dirs;
+
+ sch_gpio_resume_set(gc, gpio_num, val);
+
+ spin_lock(&gpio_lock);
+
+ curr_dirs = inb(gpio_ba + RGIO);
+ if (curr_dirs & (1 << gpio_num))
+ outb(curr_dirs & ~(1 << gpio_num), gpio_ba + RGIO);
+
+ spin_unlock(&gpio_lock);
+ return 0;
+}
+
+static struct gpio_chip sch_gpio_resume = {
+ .label = "sch_gpio_resume",
+ .owner = THIS_MODULE,
+ .direction_input = sch_gpio_resume_direction_in,
+ .get = sch_gpio_resume_get,
+ .direction_output = sch_gpio_resume_direction_out,
+ .set = sch_gpio_resume_set,
+};
+
+static int __devinit sch_gpio_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ int err;
+
+ res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (!res)
+ return -EBUSY;
+
+ if (!request_region(res->start, resource_size(res), pdev->name))
+ return -EBUSY;
+
+ gpio_ba = res->start;
+
+ sch_gpio_core.base = 0;
+ sch_gpio_core.ngpio = 10;
+ sch_gpio_core.dev = &pdev->dev;
+
+ sch_gpio_resume.base = 10;
+ sch_gpio_resume.ngpio = 4;
+ sch_gpio_resume.dev = &pdev->dev;
+
+ err = gpiochip_add(&sch_gpio_core);
+ if (err < 0)
+ goto err_sch_gpio_core;
+
+ err = gpiochip_add(&sch_gpio_resume);
+ if (err < 0)
+ goto err_sch_gpio_resume;
+
+ /*
+ * GPIO[6:0] enabled by default
+ * GPIO7 is configured by the CMC as SLPIOVR
+ * Enable GPIO[9:8] core powered gpios explicitly
+ */
+ outb(0x3, gpio_ba + CGEN + 1);
+ /*
+ * SUS_GPIO[2:0] enabled by default
+ * Enable SUS_GPIO3 resume powered gpio explicitly
+ */
+ outb(0x8, gpio_ba + RGEN);
+
+ return 0;
+
+err_sch_gpio_resume:
+ err = gpiochip_remove(&sch_gpio_core);
+ if (err)
+ dev_err(&pdev->dev, "%s failed, %d\n",
+ "gpiochip_remove()", err);
+
+err_sch_gpio_core:
+ release_region(res->start, resource_size(res));
+ gpio_ba = 0;
+
+ return err;
+}
+
+static int __devexit sch_gpio_remove(struct platform_device *pdev)
+{
+ struct resource *res;
+ if (gpio_ba) {
+ int err;
+
+ err = gpiochip_remove(&sch_gpio_core);
+ if (err)
+ dev_err(&pdev->dev, "%s failed, %d\n",
+ "gpiochip_remove()", err);
+ err = gpiochip_remove(&sch_gpio_resume);
+ if (err)
+ dev_err(&pdev->dev, "%s failed, %d\n",
+ "gpiochip_remove()", err);
+
+ res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+
+ release_region(res->start, resource_size(res));
+ gpio_ba = 0;
+
+ return err;
+ }
+
+ return 0;
+}
+
+static struct platform_driver sch_gpio_driver = {
+ .driver = {
+ .name = "sch_gpio",
+ .owner = THIS_MODULE,
+ },
+ .probe = sch_gpio_probe,
+ .remove = __devexit_p(sch_gpio_remove),
+};
+
+static int __init sch_gpio_init(void)
+{
+ return platform_driver_register(&sch_gpio_driver);
+}
+
+static void __exit sch_gpio_exit(void)
+{
+ platform_driver_unregister(&sch_gpio_driver);
+}
+
+module_init(sch_gpio_init);
+module_exit(sch_gpio_exit);
+
+MODULE_AUTHOR("Denis Turischev <denis@compulab.co.il>");
+MODULE_DESCRIPTION("GPIO interface for Intel Poulsbo SCH");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:sch_gpio");
diff --git a/drivers/gpio/timbgpio.c b/drivers/gpio/timbgpio.c
index a4d344ba8e5..d4295fa5369 100644
--- a/drivers/gpio/timbgpio.c
+++ b/drivers/gpio/timbgpio.c
@@ -23,6 +23,7 @@
#include <linux/module.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
+#include <linux/irq.h>
#include <linux/io.h>
#include <linux/timb_gpio.h>
#include <linux/interrupt.h>
@@ -37,6 +38,8 @@
#define TGPIO_ICR 0x14
#define TGPIO_FLR 0x18
#define TGPIO_LVR 0x1c
+#define TGPIO_VER 0x20
+#define TGPIO_BFLR 0x24
struct timbgpio {
void __iomem *membase;
@@ -125,17 +128,23 @@ static int timbgpio_irq_type(unsigned irq, unsigned trigger)
struct timbgpio *tgpio = get_irq_chip_data(irq);
int offset = irq - tgpio->irq_base;
unsigned long flags;
- u32 lvr, flr;
+ u32 lvr, flr, bflr = 0;
+ u32 ver;
if (offset < 0 || offset > tgpio->gpio.ngpio)
return -EINVAL;
+ ver = ioread32(tgpio->membase + TGPIO_VER);
+
spin_lock_irqsave(&tgpio->lock, flags);
lvr = ioread32(tgpio->membase + TGPIO_LVR);
flr = ioread32(tgpio->membase + TGPIO_FLR);
+ if (ver > 2)
+ bflr = ioread32(tgpio->membase + TGPIO_BFLR);
if (trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
+ bflr &= ~(1 << offset);
flr &= ~(1 << offset);
if (trigger & IRQ_TYPE_LEVEL_HIGH)
lvr |= 1 << offset;
@@ -143,21 +152,27 @@ static int timbgpio_irq_type(unsigned irq, unsigned trigger)
lvr &= ~(1 << offset);
}
- if ((trigger & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH)
- return -EINVAL;
- else {
+ if ((trigger & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH) {
+ if (ver < 3)
+ return -EINVAL;
+ else {
+ flr |= 1 << offset;
+ bflr |= 1 << offset;
+ }
+ } else {
+ bflr &= ~(1 << offset);
flr |= 1 << offset;
- /* opposite compared to the datasheet, but it mirrors the
- * reality
- */
if (trigger & IRQ_TYPE_EDGE_FALLING)
- lvr |= 1 << offset;
- else
lvr &= ~(1 << offset);
+ else
+ lvr |= 1 << offset;
}
iowrite32(lvr, tgpio->membase + TGPIO_LVR);
iowrite32(flr, tgpio->membase + TGPIO_FLR);
+ if (ver > 2)
+ iowrite32(bflr, tgpio->membase + TGPIO_BFLR);
+
iowrite32(1 << offset, tgpio->membase + TGPIO_ICR);
spin_unlock_irqrestore(&tgpio->lock, flags);
@@ -174,7 +189,7 @@ static void timbgpio_irq(unsigned int irq, struct irq_desc *desc)
ipr = ioread32(tgpio->membase + TGPIO_IPR);
iowrite32(ipr, tgpio->membase + TGPIO_ICR);
- for_each_bit(offset, &ipr, tgpio->gpio.ngpio)
+ for_each_set_bit(offset, &ipr, tgpio->gpio.ngpio)
generic_handle_irq(timbgpio_to_irq(&tgpio->gpio, offset));
}
diff --git a/drivers/gpio/wm831x-gpio.c b/drivers/gpio/wm831x-gpio.c
index b4468b61689..d09021f4a7d 100644
--- a/drivers/gpio/wm831x-gpio.c
+++ b/drivers/gpio/wm831x-gpio.c
@@ -38,10 +38,14 @@ static int wm831x_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
{
struct wm831x_gpio *wm831x_gpio = to_wm831x_gpio(chip);
struct wm831x *wm831x = wm831x_gpio->wm831x;
+ int val = WM831X_GPN_DIR;
+
+ if (wm831x->has_gpio_ena)
+ val |= WM831X_GPN_TRI;
return wm831x_set_bits(wm831x, WM831X_GPIO1_CONTROL + offset,
- WM831X_GPN_DIR | WM831X_GPN_TRI,
- WM831X_GPN_DIR);
+ WM831X_GPN_DIR | WM831X_GPN_TRI |
+ WM831X_GPN_FN_MASK, val);
}
static int wm831x_gpio_get(struct gpio_chip *chip, unsigned offset)
@@ -60,23 +64,36 @@ static int wm831x_gpio_get(struct gpio_chip *chip, unsigned offset)
return 0;
}
-static int wm831x_gpio_direction_out(struct gpio_chip *chip,
- unsigned offset, int value)
+static void wm831x_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
struct wm831x_gpio *wm831x_gpio = to_wm831x_gpio(chip);
struct wm831x *wm831x = wm831x_gpio->wm831x;
- return wm831x_set_bits(wm831x, WM831X_GPIO1_CONTROL + offset,
- WM831X_GPN_DIR | WM831X_GPN_TRI, 0);
+ wm831x_set_bits(wm831x, WM831X_GPIO_LEVEL, 1 << offset,
+ value << offset);
}
-static void wm831x_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+static int wm831x_gpio_direction_out(struct gpio_chip *chip,
+ unsigned offset, int value)
{
struct wm831x_gpio *wm831x_gpio = to_wm831x_gpio(chip);
struct wm831x *wm831x = wm831x_gpio->wm831x;
+ int val = 0;
+ int ret;
- wm831x_set_bits(wm831x, WM831X_GPIO_LEVEL, 1 << offset,
- value << offset);
+ if (wm831x->has_gpio_ena)
+ val |= WM831X_GPN_TRI;
+
+ ret = wm831x_set_bits(wm831x, WM831X_GPIO1_CONTROL + offset,
+ WM831X_GPN_DIR | WM831X_GPN_TRI |
+ WM831X_GPN_FN_MASK, val);
+ if (ret < 0)
+ return ret;
+
+ /* Can only set GPIO state once it's in output mode */
+ wm831x_gpio_set(chip, offset, value);
+
+ return 0;
}
static int wm831x_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
@@ -95,7 +112,7 @@ static void wm831x_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
{
struct wm831x_gpio *wm831x_gpio = to_wm831x_gpio(chip);
struct wm831x *wm831x = wm831x_gpio->wm831x;
- int i;
+ int i, tristated;
for (i = 0; i < chip->ngpio; i++) {
int gpio = i + chip->base;
@@ -162,15 +179,19 @@ static void wm831x_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
break;
}
+ tristated = reg & WM831X_GPN_TRI;
+ if (wm831x->has_gpio_ena)
+ tristated = !tristated;
+
seq_printf(s, " %s %s %s %s%s\n"
" %s%s (0x%4x)\n",
reg & WM831X_GPN_DIR ? "in" : "out",
wm831x_gpio_get(chip, i) ? "high" : "low",
pull,
powerdomain,
- reg & WM831X_GPN_POL ? " inverted" : "",
+ reg & WM831X_GPN_POL ? "" : " inverted",
reg & WM831X_GPN_OD ? "open-drain" : "CMOS",
- reg & WM831X_GPN_TRI ? " tristated" : "",
+ tristated ? " tristated" : "",
reg);
}
}
diff --git a/drivers/gpio/wm8350-gpiolib.c b/drivers/gpio/wm8350-gpiolib.c
new file mode 100644
index 00000000000..511840d1c7b
--- /dev/null
+++ b/drivers/gpio/wm8350-gpiolib.c
@@ -0,0 +1,181 @@
+/*
+ * wm835x-gpiolib.c -- gpiolib support for Wolfson WM835x PMICs
+ *
+ * Copyright 2009 Wolfson Microelectronics PLC.
+ *
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/gpio.h>
+#include <linux/mfd/core.h>
+#include <linux/platform_device.h>
+#include <linux/seq_file.h>
+
+#include <linux/mfd/wm8350/core.h>
+#include <linux/mfd/wm8350/gpio.h>
+
+struct wm8350_gpio_data {
+ struct wm8350 *wm8350;
+ struct gpio_chip gpio_chip;
+};
+
+static inline struct wm8350_gpio_data *to_wm8350_gpio(struct gpio_chip *chip)
+{
+ return container_of(chip, struct wm8350_gpio_data, gpio_chip);
+}
+
+static int wm8350_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
+{
+ struct wm8350_gpio_data *wm8350_gpio = to_wm8350_gpio(chip);
+ struct wm8350 *wm8350 = wm8350_gpio->wm8350;
+
+ return wm8350_set_bits(wm8350, WM8350_GPIO_CONFIGURATION_I_O,
+ 1 << offset);
+}
+
+static int wm8350_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct wm8350_gpio_data *wm8350_gpio = to_wm8350_gpio(chip);
+ struct wm8350 *wm8350 = wm8350_gpio->wm8350;
+ int ret;
+
+ ret = wm8350_reg_read(wm8350, WM8350_GPIO_LEVEL);
+ if (ret < 0)
+ return ret;
+
+ if (ret & (1 << offset))
+ return 1;
+ else
+ return 0;
+}
+
+static void wm8350_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct wm8350_gpio_data *wm8350_gpio = to_wm8350_gpio(chip);
+ struct wm8350 *wm8350 = wm8350_gpio->wm8350;
+
+ if (value)
+ wm8350_set_bits(wm8350, WM8350_GPIO_LEVEL, 1 << offset);
+ else
+ wm8350_clear_bits(wm8350, WM8350_GPIO_LEVEL, 1 << offset);
+}
+
+static int wm8350_gpio_direction_out(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct wm8350_gpio_data *wm8350_gpio = to_wm8350_gpio(chip);
+ struct wm8350 *wm8350 = wm8350_gpio->wm8350;
+ int ret;
+
+ ret = wm8350_clear_bits(wm8350, WM8350_GPIO_CONFIGURATION_I_O,
+ 1 << offset);
+ if (ret < 0)
+ return ret;
+
+ /* Don't have an atomic direction/value setup */
+ wm8350_gpio_set(chip, offset, value);
+
+ return 0;
+}
+
+static int wm8350_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ struct wm8350_gpio_data *wm8350_gpio = to_wm8350_gpio(chip);
+ struct wm8350 *wm8350 = wm8350_gpio->wm8350;
+
+ if (!wm8350->irq_base)
+ return -EINVAL;
+
+ return wm8350->irq_base + WM8350_IRQ_GPIO(offset);
+}
+
+static struct gpio_chip template_chip = {
+ .label = "wm8350",
+ .owner = THIS_MODULE,
+ .direction_input = wm8350_gpio_direction_in,
+ .get = wm8350_gpio_get,
+ .direction_output = wm8350_gpio_direction_out,
+ .set = wm8350_gpio_set,
+ .to_irq = wm8350_gpio_to_irq,
+ .can_sleep = 1,
+};
+
+static int __devinit wm8350_gpio_probe(struct platform_device *pdev)
+{
+ struct wm8350 *wm8350 = dev_get_drvdata(pdev->dev.parent);
+ struct wm8350_platform_data *pdata = wm8350->dev->platform_data;
+ struct wm8350_gpio_data *wm8350_gpio;
+ int ret;
+
+ wm8350_gpio = kzalloc(sizeof(*wm8350_gpio), GFP_KERNEL);
+ if (wm8350_gpio == NULL)
+ return -ENOMEM;
+
+ wm8350_gpio->wm8350 = wm8350;
+ wm8350_gpio->gpio_chip = template_chip;
+ wm8350_gpio->gpio_chip.ngpio = 13;
+ wm8350_gpio->gpio_chip.dev = &pdev->dev;
+ if (pdata && pdata->gpio_base)
+ wm8350_gpio->gpio_chip.base = pdata->gpio_base;
+ else
+ wm8350_gpio->gpio_chip.base = -1;
+
+ ret = gpiochip_add(&wm8350_gpio->gpio_chip);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Could not register gpiochip, %d\n",
+ ret);
+ goto err;
+ }
+
+ platform_set_drvdata(pdev, wm8350_gpio);
+
+ return ret;
+
+err:
+ kfree(wm8350_gpio);
+ return ret;
+}
+
+static int __devexit wm8350_gpio_remove(struct platform_device *pdev)
+{
+ struct wm8350_gpio_data *wm8350_gpio = platform_get_drvdata(pdev);
+ int ret;
+
+ ret = gpiochip_remove(&wm8350_gpio->gpio_chip);
+ if (ret == 0)
+ kfree(wm8350_gpio);
+
+ return ret;
+}
+
+static struct platform_driver wm8350_gpio_driver = {
+ .driver.name = "wm8350-gpio",
+ .driver.owner = THIS_MODULE,
+ .probe = wm8350_gpio_probe,
+ .remove = __devexit_p(wm8350_gpio_remove),
+};
+
+static int __init wm8350_gpio_init(void)
+{
+ return platform_driver_register(&wm8350_gpio_driver);
+}
+subsys_initcall(wm8350_gpio_init);
+
+static void __exit wm8350_gpio_exit(void)
+{
+ platform_driver_unregister(&wm8350_gpio_driver);
+}
+module_exit(wm8350_gpio_exit);
+
+MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
+MODULE_DESCRIPTION("GPIO interface for WM8350 PMICs");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:wm8350-gpio");
diff --git a/drivers/gpio/wm8994-gpio.c b/drivers/gpio/wm8994-gpio.c
new file mode 100644
index 00000000000..de28b4a470e
--- /dev/null
+++ b/drivers/gpio/wm8994-gpio.c
@@ -0,0 +1,204 @@
+/*
+ * wm8994-gpio.c -- gpiolib support for Wolfson WM8994
+ *
+ * Copyright 2009 Wolfson Microelectronics PLC.
+ *
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/gpio.h>
+#include <linux/mfd/core.h>
+#include <linux/platform_device.h>
+#include <linux/seq_file.h>
+
+#include <linux/mfd/wm8994/core.h>
+#include <linux/mfd/wm8994/pdata.h>
+#include <linux/mfd/wm8994/gpio.h>
+#include <linux/mfd/wm8994/registers.h>
+
+struct wm8994_gpio {
+ struct wm8994 *wm8994;
+ struct gpio_chip gpio_chip;
+};
+
+static inline struct wm8994_gpio *to_wm8994_gpio(struct gpio_chip *chip)
+{
+ return container_of(chip, struct wm8994_gpio, gpio_chip);
+}
+
+static int wm8994_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
+{
+ struct wm8994_gpio *wm8994_gpio = to_wm8994_gpio(chip);
+ struct wm8994 *wm8994 = wm8994_gpio->wm8994;
+
+ return wm8994_set_bits(wm8994, WM8994_GPIO_1 + offset,
+ WM8994_GPN_DIR, WM8994_GPN_DIR);
+}
+
+static int wm8994_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct wm8994_gpio *wm8994_gpio = to_wm8994_gpio(chip);
+ struct wm8994 *wm8994 = wm8994_gpio->wm8994;
+ int ret;
+
+ ret = wm8994_reg_read(wm8994, WM8994_GPIO_1 + offset);
+ if (ret < 0)
+ return ret;
+
+ if (ret & WM8994_GPN_LVL)
+ return 1;
+ else
+ return 0;
+}
+
+static int wm8994_gpio_direction_out(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct wm8994_gpio *wm8994_gpio = to_wm8994_gpio(chip);
+ struct wm8994 *wm8994 = wm8994_gpio->wm8994;
+
+ return wm8994_set_bits(wm8994, WM8994_GPIO_1 + offset,
+ WM8994_GPN_DIR, 0);
+}
+
+static void wm8994_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct wm8994_gpio *wm8994_gpio = to_wm8994_gpio(chip);
+ struct wm8994 *wm8994 = wm8994_gpio->wm8994;
+
+ if (value)
+ value = WM8994_GPN_LVL;
+
+ wm8994_set_bits(wm8994, WM8994_GPIO_1 + offset, WM8994_GPN_LVL, value);
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void wm8994_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ struct wm8994_gpio *wm8994_gpio = to_wm8994_gpio(chip);
+ struct wm8994 *wm8994 = wm8994_gpio->wm8994;
+ int i;
+
+ for (i = 0; i < chip->ngpio; i++) {
+ int gpio = i + chip->base;
+ int reg;
+ const char *label;
+
+ /* We report the GPIO even if it's not requested since
+ * we're also reporting things like alternate
+ * functions which apply even when the GPIO is not in
+ * use as a GPIO.
+ */
+ label = gpiochip_is_requested(chip, i);
+ if (!label)
+ label = "Unrequested";
+
+ seq_printf(s, " gpio-%-3d (%-20.20s) ", gpio, label);
+
+ reg = wm8994_reg_read(wm8994, WM8994_GPIO_1 + i);
+ if (reg < 0) {
+ dev_err(wm8994->dev,
+ "GPIO control %d read failed: %d\n",
+ gpio, reg);
+ seq_printf(s, "\n");
+ continue;
+ }
+
+ /* No decode yet; note that GPIO2 is special */
+ seq_printf(s, "(%x)\n", reg);
+ }
+}
+#else
+#define wm8994_gpio_dbg_show NULL
+#endif
+
+static struct gpio_chip template_chip = {
+ .label = "wm8994",
+ .owner = THIS_MODULE,
+ .direction_input = wm8994_gpio_direction_in,
+ .get = wm8994_gpio_get,
+ .direction_output = wm8994_gpio_direction_out,
+ .set = wm8994_gpio_set,
+ .dbg_show = wm8994_gpio_dbg_show,
+ .can_sleep = 1,
+};
+
+static int __devinit wm8994_gpio_probe(struct platform_device *pdev)
+{
+ struct wm8994 *wm8994 = dev_get_drvdata(pdev->dev.parent);
+ struct wm8994_pdata *pdata = wm8994->dev->platform_data;
+ struct wm8994_gpio *wm8994_gpio;
+ int ret;
+
+ wm8994_gpio = kzalloc(sizeof(*wm8994_gpio), GFP_KERNEL);
+ if (wm8994_gpio == NULL)
+ return -ENOMEM;
+
+ wm8994_gpio->wm8994 = wm8994;
+ wm8994_gpio->gpio_chip = template_chip;
+ wm8994_gpio->gpio_chip.ngpio = WM8994_GPIO_MAX;
+ wm8994_gpio->gpio_chip.dev = &pdev->dev;
+ if (pdata && pdata->gpio_base)
+ wm8994_gpio->gpio_chip.base = pdata->gpio_base;
+ else
+ wm8994_gpio->gpio_chip.base = -1;
+
+ ret = gpiochip_add(&wm8994_gpio->gpio_chip);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Could not register gpiochip, %d\n",
+ ret);
+ goto err;
+ }
+
+ platform_set_drvdata(pdev, wm8994_gpio);
+
+ return ret;
+
+err:
+ kfree(wm8994_gpio);
+ return ret;
+}
+
+static int __devexit wm8994_gpio_remove(struct platform_device *pdev)
+{
+ struct wm8994_gpio *wm8994_gpio = platform_get_drvdata(pdev);
+ int ret;
+
+ ret = gpiochip_remove(&wm8994_gpio->gpio_chip);
+ if (ret == 0)
+ kfree(wm8994_gpio);
+
+ return ret;
+}
+
+static struct platform_driver wm8994_gpio_driver = {
+ .driver.name = "wm8994-gpio",
+ .driver.owner = THIS_MODULE,
+ .probe = wm8994_gpio_probe,
+ .remove = __devexit_p(wm8994_gpio_remove),
+};
+
+static int __init wm8994_gpio_init(void)
+{
+ return platform_driver_register(&wm8994_gpio_driver);
+}
+subsys_initcall(wm8994_gpio_init);
+
+static void __exit wm8994_gpio_exit(void)
+{
+ platform_driver_unregister(&wm8994_gpio_driver);
+}
+module_exit(wm8994_gpio_exit);
+
+MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
+MODULE_DESCRIPTION("GPIO interface for WM8994");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:wm8994-gpio");