diff options
Diffstat (limited to 'drivers/gpu/drm/exynos/exynos_drm_dsi.c')
| -rw-r--r-- | drivers/gpu/drm/exynos/exynos_drm_dsi.c | 285 |
1 files changed, 256 insertions, 29 deletions
diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c index 6302aa64f6c..442aa2d0013 100644 --- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c +++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c @@ -16,7 +16,10 @@ #include <drm/drm_panel.h> #include <linux/clk.h> +#include <linux/gpio/consumer.h> #include <linux/irq.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> #include <linux/phy/phy.h> #include <linux/regulator/consumer.h> #include <linux/component.h> @@ -24,6 +27,7 @@ #include <video/mipi_display.h> #include <video/videomode.h> +#include "exynos_drm_crtc.h" #include "exynos_drm_drv.h" /* returns true iff both arguments logically differs */ @@ -54,9 +58,12 @@ /* FIFO memory AC characteristic register */ #define DSIM_PLLCTRL_REG 0x4c /* PLL control register */ -#define DSIM_PLLTMR_REG 0x50 /* PLL timer register */ #define DSIM_PHYACCHR_REG 0x54 /* D-PHY AC characteristic register */ #define DSIM_PHYACCHR1_REG 0x58 /* D-PHY AC characteristic register1 */ +#define DSIM_PHYCTRL_REG 0x5c +#define DSIM_PHYTIMING_REG 0x64 +#define DSIM_PHYTIMING1_REG 0x68 +#define DSIM_PHYTIMING2_REG 0x6c /* DSIM_STATUS */ #define DSIM_STOP_STATE_DAT(x) (((x) & 0xf) << 0) @@ -200,6 +207,24 @@ #define DSIM_PLL_M(x) ((x) << 4) #define DSIM_PLL_S(x) ((x) << 1) +/* DSIM_PHYCTRL */ +#define DSIM_PHYCTRL_ULPS_EXIT(x) (((x) & 0x1ff) << 0) + +/* DSIM_PHYTIMING */ +#define DSIM_PHYTIMING_LPX(x) ((x) << 8) +#define DSIM_PHYTIMING_HS_EXIT(x) ((x) << 0) + +/* DSIM_PHYTIMING1 */ +#define DSIM_PHYTIMING1_CLK_PREPARE(x) ((x) << 24) +#define DSIM_PHYTIMING1_CLK_ZERO(x) ((x) << 16) +#define DSIM_PHYTIMING1_CLK_POST(x) ((x) << 8) +#define DSIM_PHYTIMING1_CLK_TRAIL(x) ((x) << 0) + +/* DSIM_PHYTIMING2 */ +#define DSIM_PHYTIMING2_HS_PREPARE(x) ((x) << 16) +#define DSIM_PHYTIMING2_HS_ZERO(x) ((x) << 8) +#define DSIM_PHYTIMING2_HS_TRAIL(x) ((x) << 0) + #define DSI_MAX_BUS_WIDTH 4 #define DSI_NUM_VIRTUAL_CHANNELS 4 #define DSI_TX_FIFO_SIZE 2048 @@ -233,6 +258,12 @@ struct exynos_dsi_transfer { #define DSIM_STATE_INITIALIZED BIT(1) #define DSIM_STATE_CMD_LPM BIT(2) +struct exynos_dsi_driver_data { + unsigned int plltmr_reg; + + unsigned int has_freqband:1; +}; + struct exynos_dsi { struct mipi_dsi_host dsi_host; struct drm_connector connector; @@ -247,6 +278,7 @@ struct exynos_dsi { struct clk *bus_clk; struct regulator_bulk_data supplies[2]; int irq; + int te_gpio; u32 pll_clk_rate; u32 burst_clk_rate; @@ -262,11 +294,39 @@ struct exynos_dsi { spinlock_t transfer_lock; /* protects transfer_list */ struct list_head transfer_list; + + struct exynos_dsi_driver_data *driver_data; }; #define host_to_dsi(host) container_of(host, struct exynos_dsi, dsi_host) #define connector_to_dsi(c) container_of(c, struct exynos_dsi, connector) +static struct exynos_dsi_driver_data exynos4_dsi_driver_data = { + .plltmr_reg = 0x50, + .has_freqband = 1, +}; + +static struct exynos_dsi_driver_data exynos5_dsi_driver_data = { + .plltmr_reg = 0x58, +}; + +static struct of_device_id exynos_dsi_of_match[] = { + { .compatible = "samsung,exynos4210-mipi-dsi", + .data = &exynos4_dsi_driver_data }, + { .compatible = "samsung,exynos5410-mipi-dsi", + .data = &exynos5_dsi_driver_data }, + { } +}; + +static inline struct exynos_dsi_driver_data *exynos_dsi_get_driver_data( + struct platform_device *pdev) +{ + const struct of_device_id *of_id = + of_match_device(exynos_dsi_of_match, &pdev->dev); + + return (struct exynos_dsi_driver_data *)of_id->data; +} + static void exynos_dsi_wait_for_reset(struct exynos_dsi *dsi) { if (wait_for_completion_timeout(&dsi->completed, msecs_to_jiffies(300))) @@ -340,14 +400,9 @@ static unsigned long exynos_dsi_pll_find_pms(struct exynos_dsi *dsi, static unsigned long exynos_dsi_set_pll(struct exynos_dsi *dsi, unsigned long freq) { - static const unsigned long freq_bands[] = { - 100 * MHZ, 120 * MHZ, 160 * MHZ, 200 * MHZ, - 270 * MHZ, 320 * MHZ, 390 * MHZ, 450 * MHZ, - 510 * MHZ, 560 * MHZ, 640 * MHZ, 690 * MHZ, - 770 * MHZ, 870 * MHZ, 950 * MHZ, - }; + struct exynos_dsi_driver_data *driver_data = dsi->driver_data; unsigned long fin, fout; - int timeout, band; + int timeout; u8 p, s; u16 m; u32 reg; @@ -368,18 +423,30 @@ static unsigned long exynos_dsi_set_pll(struct exynos_dsi *dsi, "failed to find PLL PMS for requested frequency\n"); return -EFAULT; } + dev_dbg(dsi->dev, "PLL freq %lu, (p %d, m %d, s %d)\n", fout, p, m, s); - for (band = 0; band < ARRAY_SIZE(freq_bands); ++band) - if (fout < freq_bands[band]) - break; + writel(500, dsi->reg_base + driver_data->plltmr_reg); + + reg = DSIM_PLL_EN | DSIM_PLL_P(p) | DSIM_PLL_M(m) | DSIM_PLL_S(s); - dev_dbg(dsi->dev, "PLL freq %lu, (p %d, m %d, s %d), band %d\n", fout, - p, m, s, band); + if (driver_data->has_freqband) { + static const unsigned long freq_bands[] = { + 100 * MHZ, 120 * MHZ, 160 * MHZ, 200 * MHZ, + 270 * MHZ, 320 * MHZ, 390 * MHZ, 450 * MHZ, + 510 * MHZ, 560 * MHZ, 640 * MHZ, 690 * MHZ, + 770 * MHZ, 870 * MHZ, 950 * MHZ, + }; + int band; - writel(500, dsi->reg_base + DSIM_PLLTMR_REG); + for (band = 0; band < ARRAY_SIZE(freq_bands); ++band) + if (fout < freq_bands[band]) + break; + + dev_dbg(dsi->dev, "band %d\n", band); + + reg |= DSIM_FREQ_BAND(band); + } - reg = DSIM_FREQ_BAND(band) | DSIM_PLL_EN - | DSIM_PLL_P(p) | DSIM_PLL_M(m) | DSIM_PLL_S(s); writel(reg, dsi->reg_base + DSIM_PLLCTRL_REG); timeout = 1000; @@ -433,6 +500,59 @@ static int exynos_dsi_enable_clock(struct exynos_dsi *dsi) return 0; } +static void exynos_dsi_set_phy_ctrl(struct exynos_dsi *dsi) +{ + struct exynos_dsi_driver_data *driver_data = dsi->driver_data; + u32 reg; + + if (driver_data->has_freqband) + return; + + /* B D-PHY: D-PHY Master & Slave Analog Block control */ + reg = DSIM_PHYCTRL_ULPS_EXIT(0x0af); + writel(reg, dsi->reg_base + DSIM_PHYCTRL_REG); + + /* + * T LPX: Transmitted length of any Low-Power state period + * T HS-EXIT: Time that the transmitter drives LP-11 following a HS + * burst + */ + reg = DSIM_PHYTIMING_LPX(0x06) | DSIM_PHYTIMING_HS_EXIT(0x0b); + writel(reg, dsi->reg_base + DSIM_PHYTIMING_REG); + + /* + * T CLK-PREPARE: Time that the transmitter drives the Clock Lane LP-00 + * Line state immediately before the HS-0 Line state starting the + * HS transmission + * T CLK-ZERO: Time that the transmitter drives the HS-0 state prior to + * transmitting the Clock. + * T CLK_POST: Time that the transmitter continues to send HS clock + * after the last associated Data Lane has transitioned to LP Mode + * Interval is defined as the period from the end of T HS-TRAIL to + * the beginning of T CLK-TRAIL + * T CLK-TRAIL: Time that the transmitter drives the HS-0 state after + * the last payload clock bit of a HS transmission burst + */ + reg = DSIM_PHYTIMING1_CLK_PREPARE(0x07) | + DSIM_PHYTIMING1_CLK_ZERO(0x27) | + DSIM_PHYTIMING1_CLK_POST(0x0d) | + DSIM_PHYTIMING1_CLK_TRAIL(0x08); + writel(reg, dsi->reg_base + DSIM_PHYTIMING1_REG); + + /* + * T HS-PREPARE: Time that the transmitter drives the Data Lane LP-00 + * Line state immediately before the HS-0 Line state starting the + * HS transmission + * T HS-ZERO: Time that the transmitter drives the HS-0 state prior to + * transmitting the Sync sequence. + * T HS-TRAIL: Time that the transmitter drives the flipped differential + * state after last payload data bit of a HS transmission burst + */ + reg = DSIM_PHYTIMING2_HS_PREPARE(0x09) | DSIM_PHYTIMING2_HS_ZERO(0x0d) | + DSIM_PHYTIMING2_HS_TRAIL(0x0b); + writel(reg, dsi->reg_base + DSIM_PHYTIMING2_REG); +} + static void exynos_dsi_disable_clock(struct exynos_dsi *dsi) { u32 reg; @@ -468,13 +588,20 @@ static int exynos_dsi_init_link(struct exynos_dsi *dsi) /* DSI configuration */ reg = 0; + /* + * The first bit of mode_flags specifies display configuration. + * If this bit is set[= MIPI_DSI_MODE_VIDEO], dsi will support video + * mode, otherwise it will support command mode. + */ if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) { reg |= DSIM_VIDEO_MODE; + /* + * The user manual describes that following bits are ignored in + * command mode. + */ if (!(dsi->mode_flags & MIPI_DSI_MODE_VSYNC_FLUSH)) reg |= DSIM_MFLUSH_VS; - if (!(dsi->mode_flags & MIPI_DSI_MODE_EOT_PACKET)) - reg |= DSIM_EOT_DISABLE; if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) reg |= DSIM_SYNC_INFORM; if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) @@ -491,6 +618,9 @@ static int exynos_dsi_init_link(struct exynos_dsi *dsi) reg |= DSIM_HSA_MODE; } + if (!(dsi->mode_flags & MIPI_DSI_MODE_EOT_PACKET)) + reg |= DSIM_EOT_DISABLE; + switch (dsi->format) { case MIPI_DSI_FMT_RGB888: reg |= DSIM_MAIN_PIX_FORMAT_RGB888; @@ -944,17 +1074,90 @@ static irqreturn_t exynos_dsi_irq(int irq, void *dev_id) return IRQ_HANDLED; } +static irqreturn_t exynos_dsi_te_irq_handler(int irq, void *dev_id) +{ + struct exynos_dsi *dsi = (struct exynos_dsi *)dev_id; + struct drm_encoder *encoder = dsi->encoder; + + if (dsi->state & DSIM_STATE_ENABLED) + exynos_drm_crtc_te_handler(encoder->crtc); + + return IRQ_HANDLED; +} + +static void exynos_dsi_enable_irq(struct exynos_dsi *dsi) +{ + enable_irq(dsi->irq); + + if (gpio_is_valid(dsi->te_gpio)) + enable_irq(gpio_to_irq(dsi->te_gpio)); +} + +static void exynos_dsi_disable_irq(struct exynos_dsi *dsi) +{ + if (gpio_is_valid(dsi->te_gpio)) + disable_irq(gpio_to_irq(dsi->te_gpio)); + + disable_irq(dsi->irq); +} + static int exynos_dsi_init(struct exynos_dsi *dsi) { - exynos_dsi_enable_clock(dsi); exynos_dsi_reset(dsi); - enable_irq(dsi->irq); + exynos_dsi_enable_irq(dsi); + exynos_dsi_enable_clock(dsi); exynos_dsi_wait_for_reset(dsi); + exynos_dsi_set_phy_ctrl(dsi); exynos_dsi_init_link(dsi); return 0; } +static int exynos_dsi_register_te_irq(struct exynos_dsi *dsi) +{ + int ret; + + dsi->te_gpio = of_get_named_gpio(dsi->panel_node, "te-gpios", 0); + if (!gpio_is_valid(dsi->te_gpio)) { + dev_err(dsi->dev, "no te-gpios specified\n"); + ret = dsi->te_gpio; + goto out; + } + + ret = gpio_request_one(dsi->te_gpio, GPIOF_IN, "te_gpio"); + if (ret) { + dev_err(dsi->dev, "gpio request failed with %d\n", ret); + goto out; + } + + /* + * This TE GPIO IRQ should not be set to IRQ_NOAUTOEN, because panel + * calls drm_panel_init() first then calls mipi_dsi_attach() in probe(). + * It means that te_gpio is invalid when exynos_dsi_enable_irq() is + * called by drm_panel_init() before panel is attached. + */ + ret = request_threaded_irq(gpio_to_irq(dsi->te_gpio), + exynos_dsi_te_irq_handler, NULL, + IRQF_TRIGGER_RISING, "TE", dsi); + if (ret) { + dev_err(dsi->dev, "request interrupt failed with %d\n", ret); + gpio_free(dsi->te_gpio); + goto out; + } + +out: + return ret; +} + +static void exynos_dsi_unregister_te_irq(struct exynos_dsi *dsi) +{ + if (gpio_is_valid(dsi->te_gpio)) { + free_irq(gpio_to_irq(dsi->te_gpio), dsi); + gpio_free(dsi->te_gpio); + dsi->te_gpio = -ENOENT; + } +} + static int exynos_dsi_host_attach(struct mipi_dsi_host *host, struct mipi_dsi_device *device) { @@ -968,6 +1171,19 @@ static int exynos_dsi_host_attach(struct mipi_dsi_host *host, if (dsi->connector.dev) drm_helper_hpd_irq_event(dsi->connector.dev); + /* + * This is a temporary solution and should be made by more generic way. + * + * If attached panel device is for command mode one, dsi should register + * TE interrupt handler. + */ + if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) { + int ret = exynos_dsi_register_te_irq(dsi); + + if (ret) + return ret; + } + return 0; } @@ -976,6 +1192,8 @@ static int exynos_dsi_host_detach(struct mipi_dsi_host *host, { struct exynos_dsi *dsi = host_to_dsi(host); + exynos_dsi_unregister_te_irq(dsi); + dsi->panel_node = NULL; if (dsi->connector.dev) @@ -1089,7 +1307,7 @@ static void exynos_dsi_poweroff(struct exynos_dsi *dsi) exynos_dsi_disable_clock(dsi); - disable_irq(dsi->irq); + exynos_dsi_disable_irq(dsi); } dsi->state &= ~DSIM_STATE_CMD_LPM; @@ -1115,7 +1333,7 @@ static int exynos_dsi_enable(struct exynos_dsi *dsi) if (ret < 0) return ret; - ret = drm_panel_enable(dsi->panel); + ret = drm_panel_prepare(dsi->panel); if (ret < 0) { exynos_dsi_poweroff(dsi); return ret; @@ -1124,6 +1342,14 @@ static int exynos_dsi_enable(struct exynos_dsi *dsi) exynos_dsi_set_display_mode(dsi); exynos_dsi_set_display_enable(dsi, true); + ret = drm_panel_enable(dsi->panel); + if (ret < 0) { + exynos_dsi_set_display_enable(dsi, false); + drm_panel_unprepare(dsi->panel); + exynos_dsi_poweroff(dsi); + return ret; + } + dsi->state |= DSIM_STATE_ENABLED; return 0; @@ -1134,8 +1360,9 @@ static void exynos_dsi_disable(struct exynos_dsi *dsi) if (!(dsi->state & DSIM_STATE_ENABLED)) return; - exynos_dsi_set_display_enable(dsi, false); drm_panel_disable(dsi->panel); + exynos_dsi_set_display_enable(dsi, false); + drm_panel_unprepare(dsi->panel); exynos_dsi_poweroff(dsi); dsi->state &= ~DSIM_STATE_ENABLED; @@ -1246,7 +1473,7 @@ static int exynos_dsi_create_connector(struct exynos_drm_display *display, } drm_connector_helper_add(connector, &exynos_dsi_connector_helper_funcs); - drm_sysfs_connector_add(connector); + drm_connector_register(connector); drm_mode_connector_attach_encoder(connector, encoder); return 0; @@ -1278,6 +1505,7 @@ static struct exynos_drm_display exynos_dsi_display = { .type = EXYNOS_DISPLAY_TYPE_LCD, .ops = &exynos_dsi_display_ops, }; +MODULE_DEVICE_TABLE(of, exynos_dsi_of_match); /* of_* functions will be removed after merge of of_graph patches */ static struct device_node * @@ -1435,6 +1663,9 @@ static int exynos_dsi_probe(struct platform_device *pdev) goto err_del_component; } + /* To be checked as invalid one */ + dsi->te_gpio = -ENOENT; + init_completion(&dsi->completed); spin_lock_init(&dsi->transfer_lock); INIT_LIST_HEAD(&dsi->transfer_list); @@ -1443,6 +1674,7 @@ static int exynos_dsi_probe(struct platform_device *pdev) dsi->dsi_host.dev = &pdev->dev; dsi->dev = &pdev->dev; + dsi->driver_data = exynos_dsi_get_driver_data(pdev); ret = exynos_dsi_parse_dt(dsi); if (ret) @@ -1525,11 +1757,6 @@ static int exynos_dsi_remove(struct platform_device *pdev) return 0; } -static struct of_device_id exynos_dsi_of_match[] = { - { .compatible = "samsung,exynos4210-mipi-dsi" }, - { } -}; - struct platform_driver dsi_driver = { .probe = exynos_dsi_probe, .remove = exynos_dsi_remove, |