diff options
Diffstat (limited to 'drivers/gpu/drm/i915/i915_reg.h')
| -rw-r--r-- | drivers/gpu/drm/i915/i915_reg.h | 70 |
1 files changed, 69 insertions, 1 deletions
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 64b0a3afd92..cf41c672def 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -178,6 +178,7 @@ #define MI_OVERLAY_OFF (0x2<<21) #define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0) #define MI_DISPLAY_FLIP MI_INSTR(0x14, 2) +#define MI_DISPLAY_FLIP_I915 MI_INSTR(0x14, 1) #define MI_DISPLAY_FLIP_PLANE(n) ((n) << 20) #define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1) #define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */ @@ -358,6 +359,70 @@ #define LM_BURST_LENGTH 0x00000700 #define LM_FIFO_WATERMARK 0x0000001F #define MI_ARB_STATE 0x020e4 /* 915+ only */ +#define MI_ARB_MASK_SHIFT 16 /* shift for enable bits */ + +/* Make render/texture TLB fetches lower priorty than associated data + * fetches. This is not turned on by default + */ +#define MI_ARB_RENDER_TLB_LOW_PRIORITY (1 << 15) + +/* Isoch request wait on GTT enable (Display A/B/C streams). + * Make isoch requests stall on the TLB update. May cause + * display underruns (test mode only) + */ +#define MI_ARB_ISOCH_WAIT_GTT (1 << 14) + +/* Block grant count for isoch requests when block count is + * set to a finite value. + */ +#define MI_ARB_BLOCK_GRANT_MASK (3 << 12) +#define MI_ARB_BLOCK_GRANT_8 (0 << 12) /* for 3 display planes */ +#define MI_ARB_BLOCK_GRANT_4 (1 << 12) /* for 2 display planes */ +#define MI_ARB_BLOCK_GRANT_2 (2 << 12) /* for 1 display plane */ +#define MI_ARB_BLOCK_GRANT_0 (3 << 12) /* don't use */ + +/* Enable render writes to complete in C2/C3/C4 power states. + * If this isn't enabled, render writes are prevented in low + * power states. That seems bad to me. + */ +#define MI_ARB_C3_LP_WRITE_ENABLE (1 << 11) + +/* This acknowledges an async flip immediately instead + * of waiting for 2TLB fetches. + */ +#define MI_ARB_ASYNC_FLIP_ACK_IMMEDIATE (1 << 10) + +/* Enables non-sequential data reads through arbiter + */ +#define MI_ARB_DUAL_DATA_PHASE_DISABLE (1 << 9) + +/* Disable FSB snooping of cacheable write cycles from binner/render + * command stream + */ +#define MI_ARB_CACHE_SNOOP_DISABLE (1 << 8) + +/* Arbiter time slice for non-isoch streams */ +#define MI_ARB_TIME_SLICE_MASK (7 << 5) +#define MI_ARB_TIME_SLICE_1 (0 << 5) +#define MI_ARB_TIME_SLICE_2 (1 << 5) +#define MI_ARB_TIME_SLICE_4 (2 << 5) +#define MI_ARB_TIME_SLICE_6 (3 << 5) +#define MI_ARB_TIME_SLICE_8 (4 << 5) +#define MI_ARB_TIME_SLICE_10 (5 << 5) +#define MI_ARB_TIME_SLICE_14 (6 << 5) +#define MI_ARB_TIME_SLICE_16 (7 << 5) + +/* Low priority grace period page size */ +#define MI_ARB_LOW_PRIORITY_GRACE_4KB (0 << 4) /* default */ +#define MI_ARB_LOW_PRIORITY_GRACE_8KB (1 << 4) + +/* Disable display A/B trickle feed */ +#define MI_ARB_DISPLAY_TRICKLE_FEED_DISABLE (1 << 2) + +/* Set display plane priority */ +#define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */ +#define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */ + #define CACHE_MODE_0 0x02120 /* 915+ only */ #define CM0_MASK_SHIFT 16 #define CM0_IZ_OPT_DISABLE (1<<6) @@ -368,6 +433,9 @@ #define CM0_RC_OP_FLUSH_DISABLE (1<<0) #define BB_ADDR 0x02140 /* 8 bytes */ #define GFX_FLSH_CNTL 0x02170 /* 915+ only */ +#define ECOSKPD 0x021d0 +#define ECO_GATING_CX_ONLY (1<<3) +#define ECO_FLIP_DONE (1<<0) /* GEN6 interrupt control */ #define GEN6_RENDER_HWSTAM 0x2098 @@ -1130,7 +1198,6 @@ #define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4) #define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2) #define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2) -#define CRT_HOTPLUG_MASK (0x3fc) /* Bits 9-2 */ #define PORT_HOTPLUG_STAT 0x61114 #define HDMIB_HOTPLUG_INT_STATUS (1 << 29) @@ -2802,6 +2869,7 @@ #define PCH_PP_STATUS 0xc7200 #define PCH_PP_CONTROL 0xc7204 +#define PANEL_UNLOCK_REGS (0xabcd << 16) #define EDP_FORCE_VDD (1 << 3) #define EDP_BLC_ENABLE (1 << 2) #define PANEL_POWER_RESET (1 << 1) |