diff options
Diffstat (limited to 'drivers/gpu/drm/i915/i915_reg.h')
| -rw-r--r-- | drivers/gpu/drm/i915/i915_reg.h | 335 |
1 files changed, 211 insertions, 124 deletions
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 4f5e15577e8..25ed911a311 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -25,52 +25,16 @@ #ifndef _I915_REG_H_ #define _I915_REG_H_ +#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a))) + /* * The Bridge device's PCI config space has information about the * fb aperture size and the amount of pre-reserved memory. + * This is all handled in the intel-gtt.ko module. i915.ko only + * cares about the vga bit for the vga rbiter. */ #define INTEL_GMCH_CTRL 0x52 #define INTEL_GMCH_VGA_DISABLE (1 << 1) -#define INTEL_GMCH_ENABLED 0x4 -#define INTEL_GMCH_MEM_MASK 0x1 -#define INTEL_GMCH_MEM_64M 0x1 -#define INTEL_GMCH_MEM_128M 0 - -#define INTEL_GMCH_GMS_MASK (0xf << 4) -#define INTEL_855_GMCH_GMS_DISABLED (0x0 << 4) -#define INTEL_855_GMCH_GMS_STOLEN_1M (0x1 << 4) -#define INTEL_855_GMCH_GMS_STOLEN_4M (0x2 << 4) -#define INTEL_855_GMCH_GMS_STOLEN_8M (0x3 << 4) -#define INTEL_855_GMCH_GMS_STOLEN_16M (0x4 << 4) -#define INTEL_855_GMCH_GMS_STOLEN_32M (0x5 << 4) - -#define INTEL_915G_GMCH_GMS_STOLEN_48M (0x6 << 4) -#define INTEL_915G_GMCH_GMS_STOLEN_64M (0x7 << 4) -#define INTEL_GMCH_GMS_STOLEN_128M (0x8 << 4) -#define INTEL_GMCH_GMS_STOLEN_256M (0x9 << 4) -#define INTEL_GMCH_GMS_STOLEN_96M (0xa << 4) -#define INTEL_GMCH_GMS_STOLEN_160M (0xb << 4) -#define INTEL_GMCH_GMS_STOLEN_224M (0xc << 4) -#define INTEL_GMCH_GMS_STOLEN_352M (0xd << 4) - -#define SNB_GMCH_CTRL 0x50 -#define SNB_GMCH_GMS_STOLEN_MASK 0xF8 -#define SNB_GMCH_GMS_STOLEN_32M (1 << 3) -#define SNB_GMCH_GMS_STOLEN_64M (2 << 3) -#define SNB_GMCH_GMS_STOLEN_96M (3 << 3) -#define SNB_GMCH_GMS_STOLEN_128M (4 << 3) -#define SNB_GMCH_GMS_STOLEN_160M (5 << 3) -#define SNB_GMCH_GMS_STOLEN_192M (6 << 3) -#define SNB_GMCH_GMS_STOLEN_224M (7 << 3) -#define SNB_GMCH_GMS_STOLEN_256M (8 << 3) -#define SNB_GMCH_GMS_STOLEN_288M (9 << 3) -#define SNB_GMCH_GMS_STOLEN_320M (0xa << 3) -#define SNB_GMCH_GMS_STOLEN_352M (0xb << 3) -#define SNB_GMCH_GMS_STOLEN_384M (0xc << 3) -#define SNB_GMCH_GMS_STOLEN_416M (0xd << 3) -#define SNB_GMCH_GMS_STOLEN_448M (0xe << 3) -#define SNB_GMCH_GMS_STOLEN_480M (0xf << 3) -#define SNB_GMCH_GMS_STOLEN_512M (0x10 << 3) /* PCI config space */ @@ -106,10 +70,13 @@ #define I915_GC_RENDER_CLOCK_200_MHZ (1 << 0) #define I915_GC_RENDER_CLOCK_333_MHZ (4 << 0) #define LBB 0xf4 -#define GDRST 0xc0 -#define GDRST_FULL (0<<2) -#define GDRST_RENDER (1<<2) -#define GDRST_MEDIA (3<<2) + +/* Graphics reset regs */ +#define I965_GDRST 0xc0 /* PCI config register */ +#define ILK_GDSR 0x2ca4 /* MCHBAR offset */ +#define GRDOM_FULL (0<<2) +#define GRDOM_RENDER (1<<2) +#define GRDOM_MEDIA (3<<2) /* VGA stuff */ @@ -192,11 +159,11 @@ #define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1) #define MI_STORE_DWORD_INDEX_SHIFT 2 #define MI_LOAD_REGISTER_IMM MI_INSTR(0x22, 1) +#define MI_FLUSH_DW MI_INSTR(0x26, 2) /* for GEN6 */ #define MI_BATCH_BUFFER MI_INSTR(0x30, 1) #define MI_BATCH_NON_SECURE (1) #define MI_BATCH_NON_SECURE_I965 (1<<8) #define MI_BATCH_BUFFER_START MI_INSTR(0x31, 0) - /* * 3D instructions used by the kernel */ @@ -249,6 +216,16 @@ #define PIPE_CONTROL_GLOBAL_GTT (1<<2) /* in addr dword */ #define PIPE_CONTROL_STALL_EN (1<<1) /* in addr word, Ironlake+ only */ + +/* + * Reset registers + */ +#define DEBUG_RESET_I830 0x6070 +#define DEBUG_RESET_FULL (1<<7) +#define DEBUG_RESET_RENDER (1<<8) +#define DEBUG_RESET_DISPLAY (1<<9) + + /* * Fence registers */ @@ -283,6 +260,17 @@ #define PRB0_HEAD 0x02034 #define PRB0_START 0x02038 #define PRB0_CTL 0x0203c +#define RENDER_RING_BASE 0x02000 +#define BSD_RING_BASE 0x04000 +#define GEN6_BSD_RING_BASE 0x12000 +#define BLT_RING_BASE 0x22000 +#define RING_TAIL(base) ((base)+0x30) +#define RING_HEAD(base) ((base)+0x34) +#define RING_START(base) ((base)+0x38) +#define RING_CTL(base) ((base)+0x3c) +#define RING_HWS_PGA(base) ((base)+0x80) +#define RING_HWS_PGA_GEN6(base) ((base)+0x2080) +#define RING_ACTHD(base) ((base)+0x74) #define TAIL_ADDR 0x001FFFF8 #define HEAD_WRAP_COUNT 0xFFE00000 #define HEAD_WRAP_ONE 0x00200000 @@ -295,6 +283,8 @@ #define RING_VALID_MASK 0x00000001 #define RING_VALID 0x00000001 #define RING_INVALID 0x00000000 +#define RING_WAIT_I8XX (1<<0) /* gen2, PRBx_HEAD */ +#define RING_WAIT (1<<11) /* gen3+, PRBx_CTL */ #define PRB1_TAIL 0x02040 /* 915+ only */ #define PRB1_HEAD 0x02044 /* 915+ only */ #define PRB1_START 0x02048 /* 915+ only */ @@ -306,7 +296,6 @@ #define INSTDONE1 0x0207c /* 965+ only */ #define ACTHD_I965 0x02074 #define HWS_PGA 0x02080 -#define HWS_PGA_GEN6 0x04080 #define HWS_ADDRESS_MASK 0xfffff000 #define HWS_START_ADDRESS_SHIFT 4 #define PWRCTXA 0x2088 /* 965GM+ only */ @@ -464,17 +453,17 @@ #define GEN6_BLITTER_COMMAND_PARSER_MASTER_ERROR (1 << 25) #define GEN6_BLITTER_SYNC_STATUS (1 << 24) #define GEN6_BLITTER_USER_INTERRUPT (1 << 22) -/* - * BSD (bit stream decoder instruction and interrupt control register defines - * (G4X and Ironlake only) - */ -#define BSD_RING_TAIL 0x04030 -#define BSD_RING_HEAD 0x04034 -#define BSD_RING_START 0x04038 -#define BSD_RING_CTL 0x0403c -#define BSD_RING_ACTHD 0x04074 -#define BSD_HWS_PGA 0x04080 +#define GEN6_BSD_SLEEP_PSMI_CONTROL 0x12050 +#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_MODIFY_MASK (1 << 16) +#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_DISABLE (1 << 0) +#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_ENABLE 0 +#define GEN6_BSD_SLEEP_PSMI_CONTROL_IDLE_INDICATOR (1 << 3) + +#define GEN6_BSD_IMR 0x120a8 +#define GEN6_BSD_IMR_USER_INTERRUPT (1 << 12) + +#define GEN6_BSD_RNCID 0x12198 /* * Framebuffer compression (915+ only) @@ -579,12 +568,51 @@ # define GPIO_DATA_VAL_IN (1 << 12) # define GPIO_DATA_PULLUP_DISABLE (1 << 13) -#define GMBUS0 0x5100 -#define GMBUS1 0x5104 -#define GMBUS2 0x5108 -#define GMBUS3 0x510c -#define GMBUS4 0x5110 -#define GMBUS5 0x5120 +#define GMBUS0 0x5100 /* clock/port select */ +#define GMBUS_RATE_100KHZ (0<<8) +#define GMBUS_RATE_50KHZ (1<<8) +#define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */ +#define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */ +#define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */ +#define GMBUS_PORT_DISABLED 0 +#define GMBUS_PORT_SSC 1 +#define GMBUS_PORT_VGADDC 2 +#define GMBUS_PORT_PANEL 3 +#define GMBUS_PORT_DPC 4 /* HDMIC */ +#define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */ + /* 6 reserved */ +#define GMBUS_PORT_DPD 7 /* HDMID */ +#define GMBUS_NUM_PORTS 8 +#define GMBUS1 0x5104 /* command/status */ +#define GMBUS_SW_CLR_INT (1<<31) +#define GMBUS_SW_RDY (1<<30) +#define GMBUS_ENT (1<<29) /* enable timeout */ +#define GMBUS_CYCLE_NONE (0<<25) +#define GMBUS_CYCLE_WAIT (1<<25) +#define GMBUS_CYCLE_INDEX (2<<25) +#define GMBUS_CYCLE_STOP (4<<25) +#define GMBUS_BYTE_COUNT_SHIFT 16 +#define GMBUS_SLAVE_INDEX_SHIFT 8 +#define GMBUS_SLAVE_ADDR_SHIFT 1 +#define GMBUS_SLAVE_READ (1<<0) +#define GMBUS_SLAVE_WRITE (0<<0) +#define GMBUS2 0x5108 /* status */ +#define GMBUS_INUSE (1<<15) +#define GMBUS_HW_WAIT_PHASE (1<<14) +#define GMBUS_STALL_TIMEOUT (1<<13) +#define GMBUS_INT (1<<12) +#define GMBUS_HW_RDY (1<<11) +#define GMBUS_SATOER (1<<10) +#define GMBUS_ACTIVE (1<<9) +#define GMBUS3 0x510c /* data buffer bytes 3-0 */ +#define GMBUS4 0x5110 /* interrupt mask (Pineview+) */ +#define GMBUS_SLAVE_TIMEOUT_EN (1<<4) +#define GMBUS_NAK_EN (1<<3) +#define GMBUS_IDLE_EN (1<<2) +#define GMBUS_HW_WAIT_EN (1<<1) +#define GMBUS_HW_RDY_EN (1<<0) +#define GMBUS5 0x5120 /* byte index */ +#define GMBUS_2BYTE_INDEX_EN (1<<31) /* * Clock control & power management @@ -603,6 +631,7 @@ #define VGA1_PD_P1_MASK (0x1f << 8) #define DPLL_A 0x06014 #define DPLL_B 0x06018 +#define DPLL(pipe) _PIPE(pipe, DPLL_A, DPLL_B) #define DPLL_VCO_ENABLE (1 << 31) #define DPLL_DVO_HIGH_SPEED (1 << 30) #define DPLL_SYNCLOCK_ENABLE (1 << 29) @@ -633,31 +662,6 @@ #define LVDS 0x61180 #define LVDS_ON (1<<31) -#define ADPA 0x61100 -#define ADPA_DPMS_MASK (~(3<<10)) -#define ADPA_DPMS_ON (0<<10) -#define ADPA_DPMS_SUSPEND (1<<10) -#define ADPA_DPMS_STANDBY (2<<10) -#define ADPA_DPMS_OFF (3<<10) - -#define RING_TAIL 0x00 -#define TAIL_ADDR 0x001FFFF8 -#define RING_HEAD 0x04 -#define HEAD_WRAP_COUNT 0xFFE00000 -#define HEAD_WRAP_ONE 0x00200000 -#define HEAD_ADDR 0x001FFFFC -#define RING_START 0x08 -#define START_ADDR 0xFFFFF000 -#define RING_LEN 0x0C -#define RING_NR_PAGES 0x001FF000 -#define RING_REPORT_MASK 0x00000006 -#define RING_REPORT_64K 0x00000002 -#define RING_REPORT_128K 0x00000004 -#define RING_NO_REPORT 0x00000000 -#define RING_VALID_MASK 0x00000001 -#define RING_VALID 0x00000001 -#define RING_INVALID 0x00000000 - /* Scratch pad debug 0 reg: */ #define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000 @@ -736,10 +740,13 @@ #define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f #define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0 #define DPLL_B_MD 0x06020 /* 965+ only */ +#define DPLL_MD(pipe) _PIPE(pipe, DPLL_A_MD, DPLL_B_MD) #define FPA0 0x06040 #define FPA1 0x06044 #define FPB0 0x06048 #define FPB1 0x0604c +#define FP0(pipe) _PIPE(pipe, FPA0, FPB0) +#define FP1(pipe) _PIPE(pipe, FPA1, FPB1) #define FP_N_DIV_MASK 0x003f0000 #define FP_N_PINEVIEW_DIV_MASK 0x00ff0000 #define FP_N_DIV_SHIFT 16 @@ -760,6 +767,7 @@ #define DPLLA_TEST_M_BYPASS (1 << 2) #define DPLLA_INPUT_BUFFER_ENABLE (1 << 0) #define D_STATE 0x6104 +#define DSTATE_GFX_RESET_I830 (1<<6) #define DSTATE_PLL_D3_OFF (1<<3) #define DSTATE_GFX_CLOCK_GATING (1<<1) #define DSTATE_DOT_CLOCK_GATING (1<<0) @@ -926,6 +934,8 @@ #define CLKCFG_MEM_800 (3 << 4) #define CLKCFG_MEM_MASK (7 << 4) +#define TSC1 0x11001 +#define TSE (1<<0) #define TR1 0x11006 #define TSFS 0x11020 #define TSFS_SLOPE_MASK 0x0000ff00 @@ -1070,6 +1080,8 @@ #define MEMSTAT_SRC_CTL_STDBY 3 #define RCPREVBSYTUPAVG 0x113b8 #define RCPREVBSYTDNAVG 0x113bc +#define PMMISC 0x11214 +#define MCPPCE_EN (1<<0) /* enable PM_MSG from PCH->MPC */ #define SDEW 0x1124c #define CSIEW0 0x11250 #define CSIEW1 0x11254 @@ -1150,6 +1162,15 @@ #define PIPEBSRC 0x6101c #define BCLRPAT_B 0x61020 +#define HTOTAL(pipe) _PIPE(pipe, HTOTAL_A, HTOTAL_B) +#define HBLANK(pipe) _PIPE(pipe, HBLANK_A, HBLANK_B) +#define HSYNC(pipe) _PIPE(pipe, HSYNC_A, HSYNC_B) +#define VTOTAL(pipe) _PIPE(pipe, VTOTAL_A, VTOTAL_B) +#define VBLANK(pipe) _PIPE(pipe, VBLANK_A, VBLANK_B) +#define VSYNC(pipe) _PIPE(pipe, VSYNC_A, VSYNC_B) +#define PIPESRC(pipe) _PIPE(pipe, PIPEASRC, PIPEBSRC) +#define BCLRPAT(pipe) _PIPE(pipe, BCLRPAT_A, BCLRPAT_B) + /* VGA port control */ #define ADPA 0x61100 #define ADPA_DAC_ENABLE (1<<31) @@ -1173,6 +1194,7 @@ #define ADPA_DPMS_STANDBY (2<<10) #define ADPA_DPMS_OFF (3<<10) + /* Hotplug control (945+ only) */ #define PORT_HOTPLUG_EN 0x61110 #define HDMIB_HOTPLUG_INT_EN (1 << 29) @@ -1331,6 +1353,22 @@ #define LVDS_B0B3_POWER_DOWN (0 << 2) #define LVDS_B0B3_POWER_UP (3 << 2) +/* Video Data Island Packet control */ +#define VIDEO_DIP_DATA 0x61178 +#define VIDEO_DIP_CTL 0x61170 +#define VIDEO_DIP_ENABLE (1 << 31) +#define VIDEO_DIP_PORT_B (1 << 29) +#define VIDEO_DIP_PORT_C (2 << 29) +#define VIDEO_DIP_ENABLE_AVI (1 << 21) +#define VIDEO_DIP_ENABLE_VENDOR (2 << 21) +#define VIDEO_DIP_ENABLE_SPD (8 << 21) +#define VIDEO_DIP_SELECT_AVI (0 << 19) +#define VIDEO_DIP_SELECT_VENDOR (1 << 19) +#define VIDEO_DIP_SELECT_SPD (3 << 19) +#define VIDEO_DIP_FREQ_ONCE (0 << 16) +#define VIDEO_DIP_FREQ_VSYNC (1 << 16) +#define VIDEO_DIP_FREQ_2VSYNC (2 << 16) + /* Panel power sequencing */ #define PP_STATUS 0x61200 #define PP_ON (1 << 31) @@ -1346,6 +1384,9 @@ #define PP_SEQUENCE_ON (1 << 28) #define PP_SEQUENCE_OFF (2 << 28) #define PP_SEQUENCE_MASK 0x30000000 +#define PP_CYCLE_DELAY_ACTIVE (1 << 27) +#define PP_SEQUENCE_STATE_ON_IDLE (1 << 3) +#define PP_SEQUENCE_STATE_MASK 0x0000000f #define PP_CONTROL 0x61204 #define POWER_TARGET_ON (1 << 0) #define PP_ON_DELAYS 0x61208 @@ -1481,6 +1522,7 @@ # define TV_TEST_MODE_MASK (7 << 0) #define TV_DAC 0x68004 +# define TV_DAC_SAVE 0x00ffff00 /** * Reports that DAC state change logic has reported change (RO). * @@ -2075,29 +2117,35 @@ /* Display & cursor control */ -/* dithering flag on Ironlake */ -#define PIPE_ENABLE_DITHER (1 << 4) -#define PIPE_DITHER_TYPE_MASK (3 << 2) -#define PIPE_DITHER_TYPE_SPATIAL (0 << 2) -#define PIPE_DITHER_TYPE_ST01 (1 << 2) /* Pipe A */ #define PIPEADSL 0x70000 -#define DSL_LINEMASK 0x00000fff +#define DSL_LINEMASK 0x00000fff #define PIPEACONF 0x70008 -#define PIPEACONF_ENABLE (1<<31) -#define PIPEACONF_DISABLE 0 -#define PIPEACONF_DOUBLE_WIDE (1<<30) +#define PIPECONF_ENABLE (1<<31) +#define PIPECONF_DISABLE 0 +#define PIPECONF_DOUBLE_WIDE (1<<30) #define I965_PIPECONF_ACTIVE (1<<30) -#define PIPEACONF_SINGLE_WIDE 0 -#define PIPEACONF_PIPE_UNLOCKED 0 -#define PIPEACONF_PIPE_LOCKED (1<<25) -#define PIPEACONF_PALETTE 0 -#define PIPEACONF_GAMMA (1<<24) +#define PIPECONF_SINGLE_WIDE 0 +#define PIPECONF_PIPE_UNLOCKED 0 +#define PIPECONF_PIPE_LOCKED (1<<25) +#define PIPECONF_PALETTE 0 +#define PIPECONF_GAMMA (1<<24) #define PIPECONF_FORCE_BORDER (1<<25) #define PIPECONF_PROGRESSIVE (0 << 21) #define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21) #define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21) #define PIPECONF_CXSR_DOWNCLOCK (1<<16) +#define PIPECONF_BPP_MASK (0x000000e0) +#define PIPECONF_BPP_8 (0<<5) +#define PIPECONF_BPP_10 (1<<5) +#define PIPECONF_BPP_6 (2<<5) +#define PIPECONF_BPP_12 (3<<5) +#define PIPECONF_DITHER_EN (1<<4) +#define PIPECONF_DITHER_TYPE_MASK (0x0000000c) +#define PIPECONF_DITHER_TYPE_SP (0<<2) +#define PIPECONF_DITHER_TYPE_ST1 (1<<2) +#define PIPECONF_DITHER_TYPE_ST2 (2<<2) +#define PIPECONF_DITHER_TYPE_TEMP (3<<2) #define PIPEASTAT 0x70024 #define PIPE_FIFO_UNDERRUN_STATUS (1UL<<31) #define PIPE_CRC_ERROR_ENABLE (1UL<<29) @@ -2128,12 +2176,15 @@ #define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */ #define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1) #define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0) -#define PIPE_BPC_MASK (7 << 5) /* Ironlake */ +#define PIPE_BPC_MASK (7 << 5) /* Ironlake */ #define PIPE_8BPC (0 << 5) #define PIPE_10BPC (1 << 5) #define PIPE_6BPC (2 << 5) #define PIPE_12BPC (3 << 5) +#define PIPECONF(pipe) _PIPE(pipe, PIPEACONF, PIPEBCONF) +#define PIPEDSL(pipe) _PIPE(pipe, PIPEADSL, PIPEBDSL) + #define DSPARB 0x70030 #define DSPARB_CSTART_MASK (0x7f << 7) #define DSPARB_CSTART_SHIFT 7 @@ -2206,8 +2257,8 @@ #define WM1_LP_SR_EN (1<<31) #define WM1_LP_LATENCY_SHIFT 24 #define WM1_LP_LATENCY_MASK (0x7f<<24) -#define WM1_LP_FBC_LP1_MASK (0xf<<20) -#define WM1_LP_FBC_LP1_SHIFT 20 +#define WM1_LP_FBC_MASK (0xf<<20) +#define WM1_LP_FBC_SHIFT 20 #define WM1_LP_SR_MASK (0x1ff<<8) #define WM1_LP_SR_SHIFT 8 #define WM1_LP_CURSOR_MASK (0x3f) @@ -2333,6 +2384,14 @@ #define DSPASURF 0x7019C /* 965+ only */ #define DSPATILEOFF 0x701A4 /* 965+ only */ +#define DSPCNTR(plane) _PIPE(plane, DSPACNTR, DSPBCNTR) +#define DSPADDR(plane) _PIPE(plane, DSPAADDR, DSPBADDR) +#define DSPSTRIDE(plane) _PIPE(plane, DSPASTRIDE, DSPBSTRIDE) +#define DSPPOS(plane) _PIPE(plane, DSPAPOS, DSPBPOS) +#define DSPSIZE(plane) _PIPE(plane, DSPASIZE, DSPBSIZE) +#define DSPSURF(plane) _PIPE(plane, DSPASURF, DSPBSURF) +#define DSPTILEOFF(plane) _PIPE(plane, DSPATILEOFF, DSPBTILEOFF) + /* VBIOS flags */ #define SWF00 0x71410 #define SWF01 0x71414 @@ -2397,6 +2456,7 @@ #define RR_HW_HIGH_POWER_FRAMES_MASK 0xff00 #define FDI_PLL_BIOS_0 0x46000 +#define FDI_PLL_FB_CLOCK_MASK 0xff #define FDI_PLL_BIOS_1 0x46004 #define FDI_PLL_BIOS_2 0x46008 #define DISPLAY_PORT_PLL_BIOS_0 0x4600c @@ -2420,46 +2480,47 @@ #define PIPEA_DATA_M1 0x60030 #define TU_SIZE(x) (((x)-1) << 25) /* default size 64 */ #define TU_SIZE_MASK 0x7e000000 -#define PIPEA_DATA_M1_OFFSET 0 +#define PIPE_DATA_M1_OFFSET 0 #define PIPEA_DATA_N1 0x60034 -#define PIPEA_DATA_N1_OFFSET 0 +#define PIPE_DATA_N1_OFFSET 0 #define PIPEA_DATA_M2 0x60038 -#define PIPEA_DATA_M2_OFFSET 0 +#define PIPE_DATA_M2_OFFSET 0 #define PIPEA_DATA_N2 0x6003c -#define PIPEA_DATA_N2_OFFSET 0 +#define PIPE_DATA_N2_OFFSET 0 #define PIPEA_LINK_M1 0x60040 -#define PIPEA_LINK_M1_OFFSET 0 +#define PIPE_LINK_M1_OFFSET 0 #define PIPEA_LINK_N1 0x60044 -#define PIPEA_LINK_N1_OFFSET 0 +#define PIPE_LINK_N1_OFFSET 0 #define PIPEA_LINK_M2 0x60048 -#define PIPEA_LINK_M2_OFFSET 0 +#define PIPE_LINK_M2_OFFSET 0 #define PIPEA_LINK_N2 0x6004c -#define PIPEA_LINK_N2_OFFSET 0 +#define PIPE_LINK_N2_OFFSET 0 /* PIPEB timing regs are same start from 0x61000 */ #define PIPEB_DATA_M1 0x61030 -#define PIPEB_DATA_M1_OFFSET 0 #define PIPEB_DATA_N1 0x61034 -#define PIPEB_DATA_N1_OFFSET 0 #define PIPEB_DATA_M2 0x61038 -#define PIPEB_DATA_M2_OFFSET 0 #define PIPEB_DATA_N2 0x6103c -#define PIPEB_DATA_N2_OFFSET 0 #define PIPEB_LINK_M1 0x61040 -#define PIPEB_LINK_M1_OFFSET 0 #define PIPEB_LINK_N1 0x61044 -#define PIPEB_LINK_N1_OFFSET 0 #define PIPEB_LINK_M2 0x61048 -#define PIPEB_LINK_M2_OFFSET 0 #define PIPEB_LINK_N2 0x6104c -#define PIPEB_LINK_N2_OFFSET 0 + +#define PIPE_DATA_M1(pipe) _PIPE(pipe, PIPEA_DATA_M1, PIPEB_DATA_M1) +#define PIPE_DATA_N1(pipe) _PIPE(pipe, PIPEA_DATA_N1, PIPEB_DATA_N1) +#define PIPE_DATA_M2(pipe) _PIPE(pipe, PIPEA_DATA_M2, PIPEB_DATA_M2) +#define PIPE_DATA_N2(pipe) _PIPE(pipe, PIPEA_DATA_N2, PIPEB_DATA_N2) +#define PIPE_LINK_M1(pipe) _PIPE(pipe, PIPEA_LINK_M1, PIPEB_LINK_M1) +#define PIPE_LINK_N1(pipe) _PIPE(pipe, PIPEA_LINK_N1, PIPEB_LINK_N1) +#define PIPE_LINK_M2(pipe) _PIPE(pipe, PIPEA_LINK_M2, PIPEB_LINK_M2) +#define PIPE_LINK_N2(pipe) _PIPE(pipe, PIPEA_LINK_N2, PIPEB_LINK_N2) /* CPU panel fitter */ #define PFA_CTL_1 0x68080 @@ -2516,7 +2577,8 @@ #define GT_SYNC_STATUS (1 << 2) #define GT_USER_INTERRUPT (1 << 0) #define GT_BSD_USER_INTERRUPT (1 << 5) - +#define GT_GEN6_BSD_USER_INTERRUPT (1 << 12) +#define GT_BLT_USER_INTERRUPT (1 << 22) #define GTISR 0x44010 #define GTIMR 0x44014 @@ -2551,6 +2613,10 @@ #define SDE_PORTD_HOTPLUG_CPT (1 << 23) #define SDE_PORTC_HOTPLUG_CPT (1 << 22) #define SDE_PORTB_HOTPLUG_CPT (1 << 21) +#define SDE_HOTPLUG_MASK_CPT (SDE_CRT_HOTPLUG_CPT | \ + SDE_PORTD_HOTPLUG_CPT | \ + SDE_PORTC_HOTPLUG_CPT | \ + SDE_PORTB_HOTPLUG_CPT) #define SDEISR 0xc4000 #define SDEIMR 0xc4004 @@ -2600,11 +2666,14 @@ #define PCH_DPLL_A 0xc6014 #define PCH_DPLL_B 0xc6018 +#define PCH_DPLL(pipe) _PIPE(pipe, PCH_DPLL_A, PCH_DPLL_B) #define PCH_FPA0 0xc6040 #define PCH_FPA1 0xc6044 #define PCH_FPB0 0xc6048 #define PCH_FPB1 0xc604c +#define PCH_FP0(pipe) _PIPE(pipe, PCH_FPA0, PCH_FPB0) +#define PCH_FP1(pipe) _PIPE(pipe, PCH_FPA1, PCH_FPB1) #define PCH_DPLL_TEST 0xc606c @@ -2690,6 +2759,13 @@ #define TRANS_VBLANK_B 0xe1010 #define TRANS_VSYNC_B 0xe1014 +#define TRANS_HTOTAL(pipe) _PIPE(pipe, TRANS_HTOTAL_A, TRANS_HTOTAL_B) +#define TRANS_HBLANK(pipe) _PIPE(pipe, TRANS_HBLANK_A, TRANS_HBLANK_B) +#define TRANS_HSYNC(pipe) _PIPE(pipe, TRANS_HSYNC_A, TRANS_HSYNC_B) +#define TRANS_VTOTAL(pipe) _PIPE(pipe, TRANS_VTOTAL_A, TRANS_VTOTAL_B) +#define TRANS_VBLANK(pipe) _PIPE(pipe, TRANS_VBLANK_A, TRANS_VBLANK_B) +#define TRANS_VSYNC(pipe) _PIPE(pipe, TRANS_VSYNC_A, TRANS_VSYNC_B) + #define TRANSB_DATA_M1 0xe1030 #define TRANSB_DATA_N1 0xe1034 #define TRANSB_DATA_M2 0xe1038 @@ -2701,6 +2777,7 @@ #define TRANSACONF 0xf0008 #define TRANSBCONF 0xf1008 +#define TRANSCONF(plane) _PIPE(plane, TRANSACONF, TRANSBCONF) #define TRANS_DISABLE (0<<31) #define TRANS_ENABLE (1<<31) #define TRANS_STATE_MASK (1<<30) @@ -2721,10 +2798,15 @@ #define FDI_RXA_CHICKEN 0xc200c #define FDI_RXB_CHICKEN 0xc2010 #define FDI_RX_PHASE_SYNC_POINTER_ENABLE (1) +#define FDI_RX_CHICKEN(pipe) _PIPE(pipe, FDI_RXA_CHICKEN, FDI_RXB_CHICKEN) + +#define SOUTH_DSPCLK_GATE_D 0xc2020 +#define PCH_DPLSUNIT_CLOCK_GATE_DISABLE (1<<29) /* CPU: FDI_TX */ #define FDI_TXA_CTL 0x60100 #define FDI_TXB_CTL 0x61100 +#define FDI_TX_CTL(pipe) _PIPE(pipe, FDI_TXA_CTL, FDI_TXB_CTL) #define FDI_TX_DISABLE (0<<31) #define FDI_TX_ENABLE (1<<31) #define FDI_LINK_TRAIN_PATTERN_1 (0<<28) @@ -2766,8 +2848,8 @@ /* FDI_RX, FDI_X is hard-wired to Transcoder_X */ #define FDI_RXA_CTL 0xf000c #define FDI_RXB_CTL 0xf100c +#define FDI_RX_CTL(pipe) _PIPE(pipe, FDI_RXA_CTL, FDI_RXB_CTL) #define FDI_RX_ENABLE (1<<31) -#define FDI_RX_DISABLE (0<<31) /* train, dp width same as FDI_TX */ #define FDI_DP_PORT_WIDTH_X8 (7<<19) #define FDI_8BPC (0<<16) @@ -2782,8 +2864,7 @@ #define FDI_FS_ERR_REPORT_ENABLE (1<<9) #define FDI_FE_ERR_REPORT_ENABLE (1<<8) #define FDI_RX_ENHANCE_FRAME_ENABLE (1<<6) -#define FDI_SEL_RAWCLK (0<<4) -#define FDI_SEL_PCDCLK (1<<4) +#define FDI_PCDCLK (1<<4) /* CPT */ #define FDI_AUTO_TRAINING (1<<10) #define FDI_LINK_TRAIN_PATTERN_1_CPT (0<<8) @@ -2798,6 +2879,9 @@ #define FDI_RXA_TUSIZE2 0xf0038 #define FDI_RXB_TUSIZE1 0xf1030 #define FDI_RXB_TUSIZE2 0xf1038 +#define FDI_RX_MISC(pipe) _PIPE(pipe, FDI_RXA_MISC, FDI_RXB_MISC) +#define FDI_RX_TUSIZE1(pipe) _PIPE(pipe, FDI_RXA_TUSIZE1, FDI_RXB_TUSIZE1) +#define FDI_RX_TUSIZE2(pipe) _PIPE(pipe, FDI_RXA_TUSIZE2, FDI_RXB_TUSIZE2) /* FDI_RX interrupt register format */ #define FDI_RX_INTER_LANE_ALIGN (1<<10) @@ -2816,6 +2900,8 @@ #define FDI_RXA_IMR 0xf0018 #define FDI_RXB_IIR 0xf1014 #define FDI_RXB_IMR 0xf1018 +#define FDI_RX_IIR(pipe) _PIPE(pipe, FDI_RXA_IIR, FDI_RXB_IIR) +#define FDI_RX_IMR(pipe) _PIPE(pipe, FDI_RXA_IMR, FDI_RXB_IMR) #define FDI_PLL_CTL_1 0xfe000 #define FDI_PLL_CTL_2 0xfe004 @@ -2935,6 +3021,7 @@ #define TRANS_DP_CTL_A 0xe0300 #define TRANS_DP_CTL_B 0xe1300 #define TRANS_DP_CTL_C 0xe2300 +#define TRANS_DP_CTL(pipe) (TRANS_DP_CTL_A + (pipe) * 0x01000) #define TRANS_DP_OUTPUT_ENABLE (1<<31) #define TRANS_DP_PORT_SEL_B (0<<29) #define TRANS_DP_PORT_SEL_C (1<<29) |