summaryrefslogtreecommitdiffstats
path: root/drivers/hwmon/dme1737.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/hwmon/dme1737.c')
-rw-r--r--drivers/hwmon/dme1737.c506
1 files changed, 290 insertions, 216 deletions
diff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c
index ffb229af786..e7c6a19f3b2 100644
--- a/drivers/hwmon/dme1737.c
+++ b/drivers/hwmon/dme1737.c
@@ -82,12 +82,12 @@ enum chips { dme1737, sch5027, sch311x, sch5127 };
* --------------------------------------------------------------------- */
/* Voltages (in) numbered 0-7 (ix) */
-#define DME1737_REG_IN(ix) ((ix) < 5 ? 0x20 + (ix) : \
+#define DME1737_REG_IN(ix) ((ix) < 5 ? 0x20 + (ix) : \
(ix) < 7 ? 0x94 + (ix) : \
0x1f)
-#define DME1737_REG_IN_MIN(ix) ((ix) < 5 ? 0x44 + (ix) * 2 \
+#define DME1737_REG_IN_MIN(ix) ((ix) < 5 ? 0x44 + (ix) * 2 \
: 0x91 + (ix) * 2)
-#define DME1737_REG_IN_MAX(ix) ((ix) < 5 ? 0x45 + (ix) * 2 \
+#define DME1737_REG_IN_MAX(ix) ((ix) < 5 ? 0x45 + (ix) * 2 \
: 0x92 + (ix) * 2)
/* Temperatures (temp) numbered 0-2 (ix) */
@@ -97,14 +97,16 @@ enum chips { dme1737, sch5027, sch311x, sch5127 };
#define DME1737_REG_TEMP_OFFSET(ix) ((ix) == 0 ? 0x1f \
: 0x1c + (ix))
-/* Voltage and temperature LSBs
+/*
+ * Voltage and temperature LSBs
* The LSBs (4 bits each) are stored in 5 registers with the following layouts:
* IN_TEMP_LSB(0) = [in5, in6]
* IN_TEMP_LSB(1) = [temp3, temp1]
* IN_TEMP_LSB(2) = [in4, temp2]
* IN_TEMP_LSB(3) = [in3, in0]
* IN_TEMP_LSB(4) = [in2, in1]
- * IN_TEMP_LSB(5) = [res, in7] */
+ * IN_TEMP_LSB(5) = [res, in7]
+ */
#define DME1737_REG_IN_TEMP_LSB(ix) (0x84 + (ix))
static const u8 DME1737_REG_IN_LSB[] = {3, 4, 4, 3, 2, 0, 0, 5};
static const u8 DME1737_REG_IN_LSB_SHL[] = {4, 4, 0, 0, 0, 0, 4, 4};
@@ -127,24 +129,30 @@ static const u8 DME1737_REG_TEMP_LSB_SHL[] = {4, 4, 0};
#define DME1737_REG_PWM_MIN(ix) (0x64 + (ix)) /* only for pwm[0-2] */
#define DME1737_REG_PWM_FREQ(ix) ((ix) < 3 ? 0x5f + (ix) \
: 0xa3 + (ix))
-/* The layout of the ramp rate registers is different from the other pwm
+/*
+ * The layout of the ramp rate registers is different from the other pwm
* registers. The bits for the 3 PWMs are stored in 2 registers:
* PWM_RR(0) = [OFF3, OFF2, OFF1, RES, RR1E, RR1-2, RR1-1, RR1-0]
- * PWM_RR(1) = [RR2E, RR2-2, RR2-1, RR2-0, RR3E, RR3-2, RR3-1, RR3-0] */
+ * PWM_RR(1) = [RR2E, RR2-2, RR2-1, RR2-0, RR3E, RR3-2, RR3-1, RR3-0]
+ */
#define DME1737_REG_PWM_RR(ix) (0x62 + (ix)) /* only for pwm[0-2] */
/* Thermal zones 0-2 */
#define DME1737_REG_ZONE_LOW(ix) (0x67 + (ix))
#define DME1737_REG_ZONE_ABS(ix) (0x6a + (ix))
-/* The layout of the hysteresis registers is different from the other zone
+/*
+ * The layout of the hysteresis registers is different from the other zone
* registers. The bits for the 3 zones are stored in 2 registers:
* ZONE_HYST(0) = [H1-3, H1-2, H1-1, H1-0, H2-3, H2-2, H2-1, H2-0]
- * ZONE_HYST(1) = [H3-3, H3-2, H3-1, H3-0, RES, RES, RES, RES] */
+ * ZONE_HYST(1) = [H3-3, H3-2, H3-1, H3-0, RES, RES, RES, RES]
+ */
#define DME1737_REG_ZONE_HYST(ix) (0x6d + (ix))
-/* Alarm registers and bit mapping
+/*
+ * Alarm registers and bit mapping
* The 3 8-bit alarm registers will be concatenated to a single 32-bit
- * alarm value [0, ALARM3, ALARM2, ALARM1]. */
+ * alarm value [0, ALARM3, ALARM2, ALARM1].
+ */
#define DME1737_REG_ALARM1 0x41
#define DME1737_REG_ALARM2 0x42
#define DME1737_REG_ALARM3 0x83
@@ -257,9 +265,11 @@ static const int IN_NOMINAL_SCH5127[] = {2500, 2250, 3300, 1125, 1125, 3300,
(type) == sch5127 ? IN_NOMINAL_SCH5127 : \
IN_NOMINAL_DME1737)
-/* Voltage input
+/*
+ * Voltage input
* Voltage inputs have 16 bits resolution, limit values have 8 bits
- * resolution. */
+ * resolution.
+ */
static inline int IN_FROM_REG(int reg, int nominal, int res)
{
return (reg * nominal + (3 << (res - 3))) / (3 << (res - 2));
@@ -270,10 +280,12 @@ static inline int IN_TO_REG(int val, int nominal)
return SENSORS_LIMIT((val * 192 + nominal / 2) / nominal, 0, 255);
}
-/* Temperature input
+/*
+ * Temperature input
* The register values represent temperatures in 2's complement notation from
* -127 degrees C to +127 degrees C. Temp inputs have 16 bits resolution, limit
- * values have 8 bits resolution. */
+ * values have 8 bits resolution.
+ */
static inline int TEMP_FROM_REG(int reg, int res)
{
return (reg * 1000) >> (res - 8);
@@ -300,18 +312,19 @@ static int TEMP_RANGE_TO_REG(int val, int reg)
int i;
for (i = 15; i > 0; i--) {
- if (val > (TEMP_RANGE[i] + TEMP_RANGE[i - 1] + 1) / 2) {
+ if (val > (TEMP_RANGE[i] + TEMP_RANGE[i - 1] + 1) / 2)
break;
- }
}
return (reg & 0x0f) | (i << 4);
}
-/* Temperature hysteresis
+/*
+ * Temperature hysteresis
* Register layout:
* reg[0] = [H1-3, H1-2, H1-1, H1-0, H2-3, H2-2, H2-1, H2-0]
- * reg[1] = [H3-3, H3-2, H3-1, H3-0, xxxx, xxxx, xxxx, xxxx] */
+ * reg[1] = [H3-3, H3-2, H3-1, H3-0, xxxx, xxxx, xxxx, xxxx]
+ */
static inline int TEMP_HYST_FROM_REG(int reg, int ix)
{
return (((ix == 1) ? reg : reg >> 4) & 0x0f) * 1000;
@@ -327,11 +340,10 @@ static inline int TEMP_HYST_TO_REG(int val, int ix, int reg)
/* Fan input RPM */
static inline int FAN_FROM_REG(int reg, int tpc)
{
- if (tpc) {
+ if (tpc)
return tpc * reg;
- } else {
+ else
return (reg == 0 || reg == 0xffff) ? 0 : 90000 * 60 / reg;
- }
}
static inline int FAN_TO_REG(int val, int tpc)
@@ -344,17 +356,21 @@ static inline int FAN_TO_REG(int val, int tpc)
}
}
-/* Fan TPC (tach pulse count)
+/*
+ * Fan TPC (tach pulse count)
* Converts a register value to a TPC multiplier or returns 0 if the tachometer
- * is configured in legacy (non-tpc) mode */
+ * is configured in legacy (non-tpc) mode
+ */
static inline int FAN_TPC_FROM_REG(int reg)
{
return (reg & 0x20) ? 0 : 60 >> (reg & 0x03);
}
-/* Fan type
+/*
+ * Fan type
* The type of a fan is expressed in number of pulses-per-revolution that it
- * emits */
+ * emits
+ */
static inline int FAN_TYPE_FROM_REG(int reg)
{
int edge = (reg >> 1) & 0x03;
@@ -378,9 +394,8 @@ static int FAN_MAX_FROM_REG(int reg)
int i;
for (i = 10; i > 0; i--) {
- if (reg == FAN_MAX[i]) {
+ if (reg == FAN_MAX[i])
break;
- }
}
return 1000 + i * 500;
@@ -391,15 +406,15 @@ static int FAN_MAX_TO_REG(int val)
int i;
for (i = 10; i > 0; i--) {
- if (val > (1000 + (i - 1) * 500)) {
+ if (val > (1000 + (i - 1) * 500))
break;
- }
}
return FAN_MAX[i];
}
-/* PWM enable
+/*
+ * PWM enable
* Register to enable mapping:
* 000: 2 fan on zone 1 auto
* 001: 2 fan on zone 2 auto
@@ -408,7 +423,8 @@ static int FAN_MAX_TO_REG(int val)
* 100: -1 fan disabled
* 101: 2 fan on hottest of zones 2,3 auto
* 110: 2 fan on hottest of zones 1,2,3 auto
- * 111: 1 fan in manual mode */
+ * 111: 1 fan in manual mode
+ */
static inline int PWM_EN_FROM_REG(int reg)
{
static const int en[] = {2, 2, 2, 0, -1, 2, 2, 1};
@@ -423,7 +439,8 @@ static inline int PWM_EN_TO_REG(int val, int reg)
return (reg & 0x1f) | ((en & 0x07) << 5);
}
-/* PWM auto channels zone
+/*
+ * PWM auto channels zone
* Register to auto channels zone mapping (ACZ is a bitfield with bit x
* corresponding to zone x+1):
* 000: 001 fan on zone 1 auto
@@ -433,7 +450,8 @@ static inline int PWM_EN_TO_REG(int val, int reg)
* 100: 000 fan disabled
* 101: 110 fan on hottest of zones 2,3 auto
* 110: 111 fan on hottest of zones 1,2,3 auto
- * 111: 000 fan in manual mode */
+ * 111: 000 fan in manual mode
+ */
static inline int PWM_ACZ_FROM_REG(int reg)
{
static const int acz[] = {1, 2, 4, 0, 0, 6, 7, 0};
@@ -468,19 +486,20 @@ static int PWM_FREQ_TO_REG(int val, int reg)
i = 11;
} else {
for (i = 9; i > 0; i--) {
- if (val > (PWM_FREQ[i] + PWM_FREQ[i - 1] + 1) / 2) {
+ if (val > (PWM_FREQ[i] + PWM_FREQ[i - 1] + 1) / 2)
break;
- }
}
}
return (reg & 0xf0) | i;
}
-/* PWM ramp rate
+/*
+ * PWM ramp rate
* Register layout:
* reg[0] = [OFF3, OFF2, OFF1, RES, RR1-E, RR1-2, RR1-1, RR1-0]
- * reg[1] = [RR2-E, RR2-2, RR2-1, RR2-0, RR3-E, RR3-2, RR3-1, RR3-0] */
+ * reg[1] = [RR2-E, RR2-2, RR2-1, RR2-0, RR3-E, RR3-2, RR3-1, RR3-0]
+ */
static const u8 PWM_RR[] = {206, 104, 69, 41, 26, 18, 10, 5};
static inline int PWM_RR_FROM_REG(int reg, int ix)
@@ -495,9 +514,8 @@ static int PWM_RR_TO_REG(int val, int ix, int reg)
int i;
for (i = 0; i < 7; i++) {
- if (val > (PWM_RR[i] + PWM_RR[i + 1] + 1) / 2) {
+ if (val > (PWM_RR[i] + PWM_RR[i + 1] + 1) / 2)
break;
- }
}
return (ix == 1) ? (reg & 0x8f) | (i << 4) : (reg & 0xf8) | i;
@@ -516,9 +534,11 @@ static inline int PWM_RR_EN_TO_REG(int val, int ix, int reg)
return val ? reg | en : reg & ~en;
}
-/* PWM min/off
+/*
+ * PWM min/off
* The PWM min/off bits are part of the PMW ramp rate register 0 (see above for
- * the register layout). */
+ * the register layout).
+ */
static inline int PWM_OFF_FROM_REG(int reg, int ix)
{
return (reg >> (ix + 5)) & 0x01;
@@ -604,12 +624,13 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
/* In (voltage) registers */
for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
- /* Voltage inputs are stored as 16 bit values even
+ /*
+ * Voltage inputs are stored as 16 bit values even
* though they have only 12 bits resolution. This is
- * to make it consistent with the temp inputs. */
- if (ix == 7 && !(data->has_features & HAS_IN7)) {
+ * to make it consistent with the temp inputs.
+ */
+ if (ix == 7 && !(data->has_features & HAS_IN7))
continue;
- }
data->in[ix] = dme1737_read(data,
DME1737_REG_IN(ix)) << 8;
data->in_min[ix] = dme1737_read(data,
@@ -620,11 +641,13 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
/* Temp registers */
for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) {
- /* Temp inputs are stored as 16 bit values even
+ /*
+ * Temp inputs are stored as 16 bit values even
* though they have only 12 bits resolution. This is
* to take advantage of implicit conversions between
* register values (2's complement) and temp values
- * (signed decimal). */
+ * (signed decimal).
+ */
data->temp[ix] = dme1737_read(data,
DME1737_REG_TEMP(ix)) << 8;
data->temp_min[ix] = dme1737_read(data,
@@ -637,21 +660,21 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
}
}
- /* In and temp LSB registers
+ /*
+ * In and temp LSB registers
* The LSBs are latched when the MSBs are read, so the order in
* which the registers are read (MSB first, then LSB) is
- * important! */
+ * important!
+ */
for (ix = 0; ix < ARRAY_SIZE(lsb); ix++) {
- if (ix == 5 && !(data->has_features & HAS_IN7)) {
+ if (ix == 5 && !(data->has_features & HAS_IN7))
continue;
- }
lsb[ix] = dme1737_read(data,
DME1737_REG_IN_TEMP_LSB(ix));
}
for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
- if (ix == 7 && !(data->has_features & HAS_IN7)) {
+ if (ix == 7 && !(data->has_features & HAS_IN7))
continue;
- }
data->in[ix] |= (lsb[DME1737_REG_IN_LSB[ix]] <<
DME1737_REG_IN_LSB_SHL[ix]) & 0xf0;
}
@@ -662,11 +685,12 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
/* Fan registers */
for (ix = 0; ix < ARRAY_SIZE(data->fan); ix++) {
- /* Skip reading registers if optional fans are not
- * present */
- if (!(data->has_features & HAS_FAN(ix))) {
+ /*
+ * Skip reading registers if optional fans are not
+ * present
+ */
+ if (!(data->has_features & HAS_FAN(ix)))
continue;
- }
data->fan[ix] = dme1737_read(data,
DME1737_REG_FAN(ix));
data->fan[ix] |= dme1737_read(data,
@@ -686,11 +710,12 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
/* PWM registers */
for (ix = 0; ix < ARRAY_SIZE(data->pwm); ix++) {
- /* Skip reading registers if optional PWMs are not
- * present */
- if (!(data->has_features & HAS_PWM(ix))) {
+ /*
+ * Skip reading registers if optional PWMs are not
+ * present
+ */
+ if (!(data->has_features & HAS_PWM(ix)))
continue;
- }
data->pwm[ix] = dme1737_read(data,
DME1737_REG_PWM(ix));
data->pwm_freq[ix] = dme1737_read(data,
@@ -711,9 +736,8 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
/* Thermal zone registers */
for (ix = 0; ix < ARRAY_SIZE(data->zone_low); ix++) {
/* Skip reading registers if zone3 is not present */
- if ((ix == 2) && !(data->has_features & HAS_ZONE3)) {
+ if ((ix == 2) && !(data->has_features & HAS_ZONE3))
continue;
- }
/* sch5127 zone2 registers are special */
if ((ix == 1) && (data->type == sch5127)) {
data->zone_low[1] = dme1737_read(data,
@@ -737,8 +761,10 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
/* Alarm registers */
data->alarms = dme1737_read(data,
DME1737_REG_ALARM1);
- /* Bit 7 tells us if the other alarm registers are non-zero and
- * therefore also need to be read */
+ /*
+ * Bit 7 tells us if the other alarm registers are non-zero and
+ * therefore also need to be read
+ */
if (data->alarms & 0x80) {
data->alarms |= dme1737_read(data,
DME1737_REG_ALARM2) << 8;
@@ -746,22 +772,18 @@ static struct dme1737_data *dme1737_update_device(struct device *dev)
DME1737_REG_ALARM3) << 16;
}
- /* The ISA chips require explicit clearing of alarm bits.
+ /*
+ * The ISA chips require explicit clearing of alarm bits.
* Don't worry, an alarm will come back if the condition
- * that causes it still exists */
+ * that causes it still exists
+ */
if (!data->client) {
- if (data->alarms & 0xff0000) {
- dme1737_write(data, DME1737_REG_ALARM3,
- 0xff);
- }
- if (data->alarms & 0xff00) {
- dme1737_write(data, DME1737_REG_ALARM2,
- 0xff);
- }
- if (data->alarms & 0xff) {
- dme1737_write(data, DME1737_REG_ALARM1,
- 0xff);
- }
+ if (data->alarms & 0xff0000)
+ dme1737_write(data, DME1737_REG_ALARM3, 0xff);
+ if (data->alarms & 0xff00)
+ dme1737_write(data, DME1737_REG_ALARM2, 0xff);
+ if (data->alarms & 0xff)
+ dme1737_write(data, DME1737_REG_ALARM1, 0xff);
}
data->last_update = jiffies;
@@ -822,7 +844,12 @@ static ssize_t set_in(struct device *dev, struct device_attribute *attr,
*sensor_attr_2 = to_sensor_dev_attr_2(attr);
int ix = sensor_attr_2->index;
int fn = sensor_attr_2->nr;
- long val = simple_strtol(buf, NULL, 10);
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err)
+ return err;
mutex_lock(&data->update_lock);
switch (fn) {
@@ -901,7 +928,12 @@ static ssize_t set_temp(struct device *dev, struct device_attribute *attr,
*sensor_attr_2 = to_sensor_dev_attr_2(attr);
int ix = sensor_attr_2->index;
int fn = sensor_attr_2->nr;
- long val = simple_strtol(buf, NULL, 10);
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err)
+ return err;
mutex_lock(&data->update_lock);
switch (fn) {
@@ -952,11 +984,10 @@ static ssize_t show_zone(struct device *dev, struct device_attribute *attr,
switch (fn) {
case SYS_ZONE_AUTO_CHANNELS_TEMP:
/* check config2 for non-standard temp-to-zone mapping */
- if ((ix == 1) && (data->config2 & 0x02)) {
+ if ((ix == 1) && (data->config2 & 0x02))
res = 4;
- } else {
+ else
res = 1 << ix;
- }
break;
case SYS_ZONE_AUTO_POINT1_TEMP_HYST:
res = TEMP_FROM_REG(data->zone_low[ix], 8) -
@@ -989,7 +1020,12 @@ static ssize_t set_zone(struct device *dev, struct device_attribute *attr,
*sensor_attr_2 = to_sensor_dev_attr_2(attr);
int ix = sensor_attr_2->index;
int fn = sensor_attr_2->nr;
- long val = simple_strtol(buf, NULL, 10);
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err)
+ return err;
mutex_lock(&data->update_lock);
switch (fn) {
@@ -1014,8 +1050,10 @@ static ssize_t set_zone(struct device *dev, struct device_attribute *attr,
/* Refresh the cache */
data->zone_low[ix] = dme1737_read(data,
DME1737_REG_ZONE_LOW(ix));
- /* Modify the temp range value (which is stored in the upper
- * nibble of the pwm_freq register) */
+ /*
+ * Modify the temp range value (which is stored in the upper
+ * nibble of the pwm_freq register)
+ */
data->pwm_freq[ix] = TEMP_RANGE_TO_REG(val -
TEMP_FROM_REG(data->zone_low[ix], 8),
dme1737_read(data,
@@ -1095,7 +1133,12 @@ static ssize_t set_fan(struct device *dev, struct device_attribute *attr,
*sensor_attr_2 = to_sensor_dev_attr_2(attr);
int ix = sensor_attr_2->index;
int fn = sensor_attr_2->nr;
- long val = simple_strtol(buf, NULL, 10);
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err)
+ return err;
mutex_lock(&data->update_lock);
switch (fn) {
@@ -1170,21 +1213,19 @@ static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
switch (fn) {
case SYS_PWM:
- if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 0) {
+ if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 0)
res = 255;
- } else {
+ else
res = data->pwm[ix];
- }
break;
case SYS_PWM_FREQ:
res = PWM_FREQ_FROM_REG(data->pwm_freq[ix]);
break;
case SYS_PWM_ENABLE:
- if (ix >= 3) {
+ if (ix >= 3)
res = 1; /* pwm[5-6] hard-wired to manual mode */
- } else {
+ else
res = PWM_EN_FROM_REG(data->pwm_config[ix]);
- }
break;
case SYS_PWM_RAMP_RATE:
/* Only valid for pwm[1-3] */
@@ -1192,19 +1233,17 @@ static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
break;
case SYS_PWM_AUTO_CHANNELS_ZONE:
/* Only valid for pwm[1-3] */
- if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) {
+ if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2)
res = PWM_ACZ_FROM_REG(data->pwm_config[ix]);
- } else {
+ else
res = data->pwm_acz[ix];
- }
break;
case SYS_PWM_AUTO_PWM_MIN:
/* Only valid for pwm[1-3] */
- if (PWM_OFF_FROM_REG(data->pwm_rr[0], ix)) {
+ if (PWM_OFF_FROM_REG(data->pwm_rr[0], ix))
res = data->pwm_min[ix];
- } else {
+ else
res = 0;
- }
break;
case SYS_PWM_AUTO_POINT1_PWM:
/* Only valid for pwm[1-3] */
@@ -1233,7 +1272,12 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
*sensor_attr_2 = to_sensor_dev_attr_2(attr);
int ix = sensor_attr_2->index;
int fn = sensor_attr_2->nr;
- long val = simple_strtol(buf, NULL, 10);
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err)
+ return err;
mutex_lock(&data->update_lock);
switch (fn) {
@@ -1307,8 +1351,10 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
/* Change permissions of pwm[ix] to read-only */
dme1737_chmod_file(dev, dme1737_pwm_chmod_attr[ix],
S_IRUGO);
- /* Turn on auto mode using the saved zone channel
- * assignment */
+ /*
+ * Turn on auto mode using the saved zone channel
+ * assignment
+ */
data->pwm_config[ix] = PWM_ACZ_TO_REG(
data->pwm_acz[ix],
data->pwm_config[ix]);
@@ -1338,8 +1384,10 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
data->pwm_rr[ix > 0] = PWM_RR_TO_REG(val, ix,
data->pwm_rr[ix > 0]);
}
- /* Enable/disable the feature only if the associated PWM
- * output is in automatic mode. */
+ /*
+ * Enable/disable the feature only if the associated PWM
+ * output is in automatic mode.
+ */
if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) {
data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(val > 0, ix,
data->pwm_rr[ix > 0]);
@@ -1361,15 +1409,19 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
data->pwm_config[ix] = dme1737_read(data,
DME1737_REG_PWM_CONFIG(ix));
if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) {
- /* PWM is already in auto mode so update the temp
- * channel assignment */
+ /*
+ * PWM is already in auto mode so update the temp
+ * channel assignment
+ */
data->pwm_config[ix] = PWM_ACZ_TO_REG(val,
data->pwm_config[ix]);
dme1737_write(data, DME1737_REG_PWM_CONFIG(ix),
data->pwm_config[ix]);
} else {
- /* PWM is not in auto mode so we save the temp
- * channel assignment for later use */
+ /*
+ * PWM is not in auto mode so we save the temp
+ * channel assignment for later use
+ */
data->pwm_acz[ix] = val;
}
break;
@@ -1378,10 +1430,12 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
/* Refresh the cache */
data->pwm_min[ix] = dme1737_read(data,
DME1737_REG_PWM_MIN(ix));
- /* There are only 2 values supported for the auto_pwm_min
+ /*
+ * There are only 2 values supported for the auto_pwm_min
* value: 0 or auto_point1_pwm. So if the temperature drops
* below the auto_point1_temp_hyst value, the fan either turns
- * off or runs at auto_point1_pwm duty-cycle. */
+ * off or runs at auto_point1_pwm duty-cycle.
+ */
if (val > ((data->pwm_min[ix] + 1) / 2)) {
data->pwm_rr[0] = PWM_OFF_TO_REG(1, ix,
dme1737_read(data,
@@ -1426,7 +1480,12 @@ static ssize_t set_vrm(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct dme1737_data *data = dev_get_drvdata(dev);
- long val = simple_strtol(buf, NULL, 10);
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err)
+ return err;
data->vrm = val;
return count;
@@ -1586,10 +1645,12 @@ static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm);
static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL);
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); /* for ISA devices */
-/* This struct holds all the attributes that are always present and need to be
+/*
+ * This struct holds all the attributes that are always present and need to be
* created unconditionally. The attributes that need modification of their
* permissions are created read-only and write permissions are added or removed
- * on the fly when required */
+ * on the fly when required
+ */
static struct attribute *dme1737_attr[] = {
/* Voltages */
&sensor_dev_attr_in0_input.dev_attr.attr,
@@ -1652,9 +1713,11 @@ static const struct attribute_group dme1737_group = {
.attrs = dme1737_attr,
};
-/* The following struct holds temp offset attributes, which are not available
+/*
+ * The following struct holds temp offset attributes, which are not available
* in all chips. The following chips support them:
- * DME1737, SCH311x */
+ * DME1737, SCH311x
+ */
static struct attribute *dme1737_temp_offset_attr[] = {
&sensor_dev_attr_temp1_offset.dev_attr.attr,
&sensor_dev_attr_temp2_offset.dev_attr.attr,
@@ -1666,9 +1729,11 @@ static const struct attribute_group dme1737_temp_offset_group = {
.attrs = dme1737_temp_offset_attr,
};
-/* The following struct holds VID related attributes, which are not available
+/*
+ * The following struct holds VID related attributes, which are not available
* in all chips. The following chips support them:
- * DME1737 */
+ * DME1737
+ */
static struct attribute *dme1737_vid_attr[] = {
&dev_attr_vrm.attr,
&dev_attr_cpu0_vid.attr,
@@ -1679,9 +1744,11 @@ static const struct attribute_group dme1737_vid_group = {
.attrs = dme1737_vid_attr,
};
-/* The following struct holds temp zone 3 related attributes, which are not
+/*
+ * The following struct holds temp zone 3 related attributes, which are not
* available in all chips. The following chips support them:
- * DME1737, SCH311x, SCH5027 */
+ * DME1737, SCH311x, SCH5027
+ */
static struct attribute *dme1737_zone3_attr[] = {
&sensor_dev_attr_zone3_auto_point1_temp.dev_attr.attr,
&sensor_dev_attr_zone3_auto_point2_temp.dev_attr.attr,
@@ -1695,9 +1762,11 @@ static const struct attribute_group dme1737_zone3_group = {
};
-/* The following struct holds temp zone hysteresis related attributes, which
+/*
+ * The following struct holds temp zone hysteresis related attributes, which
* are not available in all chips. The following chips support them:
- * DME1737, SCH311x */
+ * DME1737, SCH311x
+ */
static struct attribute *dme1737_zone_hyst_attr[] = {
&sensor_dev_attr_zone1_auto_point1_temp_hyst.dev_attr.attr,
&sensor_dev_attr_zone2_auto_point1_temp_hyst.dev_attr.attr,
@@ -1709,9 +1778,11 @@ static const struct attribute_group dme1737_zone_hyst_group = {
.attrs = dme1737_zone_hyst_attr,
};
-/* The following struct holds voltage in7 related attributes, which
+/*
+ * The following struct holds voltage in7 related attributes, which
* are not available in all chips. The following chips support them:
- * SCH5127 */
+ * SCH5127
+ */
static struct attribute *dme1737_in7_attr[] = {
&sensor_dev_attr_in7_input.dev_attr.attr,
&sensor_dev_attr_in7_min.dev_attr.attr,
@@ -1724,9 +1795,11 @@ static const struct attribute_group dme1737_in7_group = {
.attrs = dme1737_in7_attr,
};
-/* The following structs hold the PWM attributes, some of which are optional.
+/*
+ * The following structs hold the PWM attributes, some of which are optional.
* Their creation depends on the chip configuration which is determined during
- * module load. */
+ * module load.
+ */
static struct attribute *dme1737_pwm1_attr[] = {
&sensor_dev_attr_pwm1.dev_attr.attr,
&sensor_dev_attr_pwm1_freq.dev_attr.attr,
@@ -1779,18 +1852,22 @@ static const struct attribute_group dme1737_pwm_group[] = {
{ .attrs = dme1737_pwm6_attr },
};
-/* The following struct holds auto PWM min attributes, which are not available
+/*
+ * The following struct holds auto PWM min attributes, which are not available
* in all chips. Their creation depends on the chip type which is determined
- * during module load. */
+ * during module load.
+ */
static struct attribute *dme1737_auto_pwm_min_attr[] = {
&sensor_dev_attr_pwm1_auto_pwm_min.dev_attr.attr,
&sensor_dev_attr_pwm2_auto_pwm_min.dev_attr.attr,
&sensor_dev_attr_pwm3_auto_pwm_min.dev_attr.attr,
};
-/* The following structs hold the fan attributes, some of which are optional.
+/*
+ * The following structs hold the fan attributes, some of which are optional.
* Their creation depends on the chip configuration which is determined during
- * module load. */
+ * module load.
+ */
static struct attribute *dme1737_fan1_attr[] = {
&sensor_dev_attr_fan1_input.dev_attr.attr,
&sensor_dev_attr_fan1_min.dev_attr.attr,
@@ -1843,8 +1920,10 @@ static const struct attribute_group dme1737_fan_group[] = {
{ .attrs = dme1737_fan6_attr },
};
-/* The permissions of the following zone attributes are changed to read-
- * writeable if the chip is *not* locked. Otherwise they stay read-only. */
+/*
+ * The permissions of the following zone attributes are changed to read-
+ * writeable if the chip is *not* locked. Otherwise they stay read-only.
+ */
static struct attribute *dme1737_zone_chmod_attr[] = {
&sensor_dev_attr_zone1_auto_point1_temp.dev_attr.attr,
&sensor_dev_attr_zone1_auto_point2_temp.dev_attr.attr,
@@ -1860,8 +1939,10 @@ static const struct attribute_group dme1737_zone_chmod_group = {
};
-/* The permissions of the following zone 3 attributes are changed to read-
- * writeable if the chip is *not* locked. Otherwise they stay read-only. */
+/*
+ * The permissions of the following zone 3 attributes are changed to read-
+ * writeable if the chip is *not* locked. Otherwise they stay read-only.
+ */
static struct attribute *dme1737_zone3_chmod_attr[] = {
&sensor_dev_attr_zone3_auto_point1_temp.dev_attr.attr,
&sensor_dev_attr_zone3_auto_point2_temp.dev_attr.attr,
@@ -1873,9 +1954,11 @@ static const struct attribute_group dme1737_zone3_chmod_group = {
.attrs = dme1737_zone3_chmod_attr,
};
-/* The permissions of the following PWM attributes are changed to read-
+/*
+ * The permissions of the following PWM attributes are changed to read-
* writeable if the chip is *not* locked and the respective PWM is available.
- * Otherwise they stay read-only. */
+ * Otherwise they stay read-only.
+ */
static struct attribute *dme1737_pwm1_chmod_attr[] = {
&sensor_dev_attr_pwm1_freq.dev_attr.attr,
&sensor_dev_attr_pwm1_enable.dev_attr.attr,
@@ -1920,8 +2003,10 @@ static const struct attribute_group dme1737_pwm_chmod_group[] = {
{ .attrs = dme1737_pwm6_chmod_attr },
};
-/* Pwm[1-3] are read-writeable if the associated pwm is in manual mode and the
- * chip is not locked. Otherwise they are read-only. */
+/*
+ * Pwm[1-3] are read-writeable if the associated pwm is in manual mode and the
+ * chip is not locked. Otherwise they are read-only.
+ */
static struct attribute *dme1737_pwm_chmod_attr[] = {
&sensor_dev_attr_pwm1.dev_attr.attr,
&sensor_dev_attr_pwm2.dev_attr.attr,
@@ -1975,9 +2060,8 @@ static void dme1737_chmod_group(struct device *dev,
{
struct attribute **attr;
- for (attr = group->attrs; *attr; attr++) {
+ for (attr = group->attrs; *attr; attr++)
dme1737_chmod_file(dev, *attr, mode);
- }
}
static void dme1737_remove_files(struct device *dev)
@@ -2003,26 +2087,20 @@ static void dme1737_remove_files(struct device *dev)
}
}
- if (data->has_features & HAS_TEMP_OFFSET) {
+ if (data->has_features & HAS_TEMP_OFFSET)
sysfs_remove_group(&dev->kobj, &dme1737_temp_offset_group);
- }
- if (data->has_features & HAS_VID) {
+ if (data->has_features & HAS_VID)
sysfs_remove_group(&dev->kobj, &dme1737_vid_group);
- }
- if (data->has_features & HAS_ZONE3) {
+ if (data->has_features & HAS_ZONE3)
sysfs_remove_group(&dev->kobj, &dme1737_zone3_group);
- }
- if (data->has_features & HAS_ZONE_HYST) {
+ if (data->has_features & HAS_ZONE_HYST)
sysfs_remove_group(&dev->kobj, &dme1737_zone_hyst_group);
- }
- if (data->has_features & HAS_IN7) {
+ if (data->has_features & HAS_IN7)
sysfs_remove_group(&dev->kobj, &dme1737_in7_group);
- }
sysfs_remove_group(&dev->kobj, &dme1737_group);
- if (!data->client) {
+ if (!data->client)
sysfs_remove_file(&dev->kobj, &dev_attr_name.attr);
- }
}
static int dme1737_create_files(struct device *dev)
@@ -2033,48 +2111,41 @@ static int dme1737_create_files(struct device *dev)
/* Create a name attribute for ISA devices */
if (!data->client) {
err = sysfs_create_file(&dev->kobj, &dev_attr_name.attr);
- if (err) {
+ if (err)
goto exit;
- }
}
/* Create standard sysfs attributes */
err = sysfs_create_group(&dev->kobj, &dme1737_group);
- if (err) {
+ if (err)
goto exit_remove;
- }
/* Create chip-dependent sysfs attributes */
if (data->has_features & HAS_TEMP_OFFSET) {
err = sysfs_create_group(&dev->kobj,
&dme1737_temp_offset_group);
- if (err) {
+ if (err)
goto exit_remove;
- }
}
if (data->has_features & HAS_VID) {
err = sysfs_create_group(&dev->kobj, &dme1737_vid_group);
- if (err) {
+ if (err)
goto exit_remove;
- }
}
if (data->has_features & HAS_ZONE3) {
err = sysfs_create_group(&dev->kobj, &dme1737_zone3_group);
- if (err) {
+ if (err)
goto exit_remove;
- }
}
if (data->has_features & HAS_ZONE_HYST) {
err = sysfs_create_group(&dev->kobj, &dme1737_zone_hyst_group);
- if (err) {
+ if (err)
goto exit_remove;
- }
}
if (data->has_features & HAS_IN7) {
err = sysfs_create_group(&dev->kobj, &dme1737_in7_group);
- if (err) {
+ if (err)
goto exit_remove;
- }
}
/* Create fan sysfs attributes */
@@ -2082,9 +2153,8 @@ static int dme1737_create_files(struct device *dev)
if (data->has_features & HAS_FAN(ix)) {
err = sysfs_create_group(&dev->kobj,
&dme1737_fan_group[ix]);
- if (err) {
+ if (err)
goto exit_remove;
- }
}
}
@@ -2093,21 +2163,21 @@ static int dme1737_create_files(struct device *dev)
if (data->has_features & HAS_PWM(ix)) {
err = sysfs_create_group(&dev->kobj,
&dme1737_pwm_group[ix]);
- if (err) {
+ if (err)
goto exit_remove;
- }
if ((data->has_features & HAS_PWM_MIN) && (ix < 3)) {
err = sysfs_create_file(&dev->kobj,
dme1737_auto_pwm_min_attr[ix]);
- if (err) {
+ if (err)
goto exit_remove;
- }
}
}
}
- /* Inform if the device is locked. Otherwise change the permissions of
- * selected attributes from read-only to read-writeable. */
+ /*
+ * Inform if the device is locked. Otherwise change the permissions of
+ * selected attributes from read-only to read-writeable.
+ */
if (data->config & 0x02) {
dev_info(dev, "Device is locked. Some attributes "
"will be read-only.\n");
@@ -2194,26 +2264,30 @@ static int dme1737_init_device(struct device *dev)
return -EFAULT;
}
- /* Determine which optional fan and pwm features are enabled (only
- * valid for I2C devices) */
+ /*
+ * Determine which optional fan and pwm features are enabled (only
+ * valid for I2C devices)
+ */
if (client) { /* I2C chip */
data->config2 = dme1737_read(data, DME1737_REG_CONFIG2);
/* Check if optional fan3 input is enabled */
- if (data->config2 & 0x04) {
+ if (data->config2 & 0x04)
data->has_features |= HAS_FAN(2);
- }
- /* Fan4 and pwm3 are only available if the client's I2C address
+ /*
+ * Fan4 and pwm3 are only available if the client's I2C address
* is the default 0x2e. Otherwise the I/Os associated with
- * these functions are used for addr enable/select. */
- if (client->addr == 0x2e) {
+ * these functions are used for addr enable/select.
+ */
+ if (client->addr == 0x2e)
data->has_features |= HAS_FAN(3) | HAS_PWM(2);
- }
- /* Determine which of the optional fan[5-6] and pwm[5-6]
+ /*
+ * Determine which of the optional fan[5-6] and pwm[5-6]
* features are enabled. For this, we need to query the runtime
* registers through the Super-IO LPC interface. Try both
- * config ports 0x2e and 0x4e. */
+ * config ports 0x2e and 0x4e.
+ */
if (dme1737_i2c_get_features(0x2e, data) &&
dme1737_i2c_get_features(0x4e, data)) {
dev_warn(dev, "Failed to query Super-IO for optional "
@@ -2271,9 +2345,11 @@ static int dme1737_init_device(struct device *dev)
((reg >> 4) & 0x03) + 1);
}
- /* Switch pwm[1-3] to manual mode if they are currently disabled and
+ /*
+ * Switch pwm[1-3] to manual mode if they are currently disabled and
* set the duty-cycles to 0% (which is identical to the PWMs being
- * disabled). */
+ * disabled).
+ */
if (!(data->config & 0x02)) {
for (ix = 0; ix < 3; ix++) {
data->pwm_config[ix] = dme1737_read(data,
@@ -2298,9 +2374,8 @@ static int dme1737_init_device(struct device *dev)
data->pwm_acz[2] = 4; /* pwm3 -> zone3 */
/* Set VRM */
- if (data->has_features & HAS_VID) {
+ if (data->has_features & HAS_VID)
data->vrm = vid_which_vrm();
- }
return 0;
}
@@ -2318,8 +2393,10 @@ static int dme1737_i2c_get_features(int sio_cip, struct dme1737_data *data)
dme1737_sio_enter(sio_cip);
- /* Check device ID
- * We currently know about two kinds of DME1737 and SCH5027. */
+ /*
+ * Check device ID
+ * We currently know about two kinds of DME1737 and SCH5027.
+ */
reg = force_id ? force_id : dme1737_sio_inb(sio_cip, 0x20);
if (!(reg == DME1737_ID_1 || reg == DME1737_ID_2 ||
reg == SCH5027_ID)) {
@@ -2338,21 +2415,19 @@ static int dme1737_i2c_get_features(int sio_cip, struct dme1737_data *data)
goto exit;
}
- /* Read the runtime registers to determine which optional features
+ /*
+ * Read the runtime registers to determine which optional features
* are enabled and available. Bits [3:2] of registers 0x43-0x46 are set
- * to '10' if the respective feature is enabled. */
- if ((inb(addr + 0x43) & 0x0c) == 0x08) { /* fan6 */
+ * to '10' if the respective feature is enabled.
+ */
+ if ((inb(addr + 0x43) & 0x0c) == 0x08) /* fan6 */
data->has_features |= HAS_FAN(5);
- }
- if ((inb(addr + 0x44) & 0x0c) == 0x08) { /* pwm6 */
+ if ((inb(addr + 0x44) & 0x0c) == 0x08) /* pwm6 */
data->has_features |= HAS_PWM(5);
- }
- if ((inb(addr + 0x45) & 0x0c) == 0x08) { /* fan5 */
+ if ((inb(addr + 0x45) & 0x0c) == 0x08) /* fan5 */
data->has_features |= HAS_FAN(4);
- }
- if ((inb(addr + 0x46) & 0x0c) == 0x08) { /* pwm5 */
+ if ((inb(addr + 0x46) & 0x0c) == 0x08) /* pwm5 */
data->has_features |= HAS_PWM(4);
- }
exit:
dme1737_sio_exit(sio_cip);
@@ -2369,9 +2444,8 @@ static int dme1737_i2c_detect(struct i2c_client *client,
u8 company, verstep = 0;
const char *name;
- if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
- }
company = i2c_smbus_read_byte_data(client, DME1737_REG_COMPANY);
verstep = i2c_smbus_read_byte_data(client, DME1737_REG_VERSTEP);
@@ -2486,8 +2560,10 @@ static int __init dme1737_isa_detect(int sio_cip, unsigned short *addr)
dme1737_sio_enter(sio_cip);
- /* Check device ID
- * We currently know about SCH3112, SCH3114, SCH3116, and SCH5127 */
+ /*
+ * Check device ID
+ * We currently know about SCH3112, SCH3114, SCH3116, and SCH5127
+ */
reg = force_id ? force_id : dme1737_sio_inb(sio_cip, 0x20);
if (!(reg == SCH3112_ID || reg == SCH3114_ID || reg == SCH3116_ID ||
reg == SCH5127_ID)) {
@@ -2507,8 +2583,10 @@ static int __init dme1737_isa_detect(int sio_cip, unsigned short *addr)
goto exit;
}
- /* Access to the hwmon registers is through an index/data register
- * pair located at offset 0x70/0x71. */
+ /*
+ * Access to the hwmon registers is through an index/data register
+ * pair located at offset 0x70/0x71.
+ */
*addr = base_addr + 0x70;
exit:
@@ -2610,11 +2688,10 @@ static int __devinit dme1737_isa_probe(struct platform_device *pdev)
}
}
- if (data->type == sch5127) {
+ if (data->type == sch5127)
data->name = "sch5127";
- } else {
+ else
data->name = "sch311x";
- }
/* Initialize the mutex */
mutex_init(&data->update_lock);
@@ -2689,9 +2766,8 @@ static int __init dme1737_init(void)
unsigned short addr;
err = i2c_add_driver(&dme1737_i2c_driver);
- if (err) {
+ if (err)
goto exit;
- }
if (dme1737_isa_detect(0x2e, &addr) &&
dme1737_isa_detect(0x4e, &addr) &&
@@ -2703,15 +2779,13 @@ static int __init dme1737_init(void)
}
err = platform_driver_register(&dme1737_isa_driver);
- if (err) {
+ if (err)
goto exit_del_i2c_driver;
- }
/* Sets global pdev as a side effect */
err = dme1737_isa_device_add(addr);
- if (err) {
+ if (err)
goto exit_del_isa_driver;
- }
return 0;
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-15 01:54:47 +0000