diff options
Diffstat (limited to 'drivers/i2c/busses/i2c-i810.c')
| -rw-r--r-- | drivers/i2c/busses/i2c-i810.c | 260 |
1 files changed, 0 insertions, 260 deletions
diff --git a/drivers/i2c/busses/i2c-i810.c b/drivers/i2c/busses/i2c-i810.c deleted file mode 100644 index 42e8d94c276..00000000000 --- a/drivers/i2c/busses/i2c-i810.c +++ /dev/null @@ -1,260 +0,0 @@ -/* - i2c-i810.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring - Copyright (c) 1998, 1999, 2000 Frodo Looijaard <frodol@dds.nl>, - Philip Edelbrock <phil@netroedge.com>, - Ralph Metzler <rjkm@thp.uni-koeln.de>, and - Mark D. Studebaker <mdsxyz123@yahoo.com> - - Based on code written by Ralph Metzler <rjkm@thp.uni-koeln.de> and - Simon Vogl - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ -/* - This interfaces to the I810/I815 to provide access to - the DDC Bus and the I2C Bus. - - SUPPORTED DEVICES PCI ID - i810AA 7121 - i810AB 7123 - i810E 7125 - i815 1132 - i845G 2562 -*/ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/i2c.h> -#include <linux/i2c-algo-bit.h> -#include <asm/io.h> - -/* GPIO register locations */ -#define I810_IOCONTROL_OFFSET 0x5000 -#define I810_HVSYNC 0x00 /* not used */ -#define I810_GPIOA 0x10 -#define I810_GPIOB 0x14 - -/* bit locations in the registers */ -#define SCL_DIR_MASK 0x0001 -#define SCL_DIR 0x0002 -#define SCL_VAL_MASK 0x0004 -#define SCL_VAL_OUT 0x0008 -#define SCL_VAL_IN 0x0010 -#define SDA_DIR_MASK 0x0100 -#define SDA_DIR 0x0200 -#define SDA_VAL_MASK 0x0400 -#define SDA_VAL_OUT 0x0800 -#define SDA_VAL_IN 0x1000 - -/* initialization states */ -#define INIT1 0x1 -#define INIT2 0x2 -#define INIT3 0x4 - -/* delays */ -#define CYCLE_DELAY 10 -#define TIMEOUT (HZ / 2) - -static void __iomem *ioaddr; - -/* The i810 GPIO registers have individual masks for each bit - so we never have to read before writing. Nice. */ - -static void bit_i810i2c_setscl(void *data, int val) -{ - writel((val ? SCL_VAL_OUT : 0) | SCL_DIR | SCL_DIR_MASK | SCL_VAL_MASK, - ioaddr + I810_GPIOB); - readl(ioaddr + I810_GPIOB); /* flush posted write */ -} - -static void bit_i810i2c_setsda(void *data, int val) -{ - writel((val ? SDA_VAL_OUT : 0) | SDA_DIR | SDA_DIR_MASK | SDA_VAL_MASK, - ioaddr + I810_GPIOB); - readl(ioaddr + I810_GPIOB); /* flush posted write */ -} - -/* The GPIO pins are open drain, so the pins could always remain outputs. - However, some chip versions don't latch the inputs unless they - are set as inputs. - We rely on the i2c-algo-bit routines to set the pins high before - reading the input from other chips. Following guidance in the 815 - prog. ref. guide, we do a "dummy write" of 0 to the register before - reading which forces the input value to be latched. We presume this - applies to the 810 as well; shouldn't hurt anyway. This is necessary to get - i2c_algo_bit bit_test=1 to pass. */ - -static int bit_i810i2c_getscl(void *data) -{ - writel(SCL_DIR_MASK, ioaddr + I810_GPIOB); - writel(0, ioaddr + I810_GPIOB); - return (0 != (readl(ioaddr + I810_GPIOB) & SCL_VAL_IN)); -} - -static int bit_i810i2c_getsda(void *data) -{ - writel(SDA_DIR_MASK, ioaddr + I810_GPIOB); - writel(0, ioaddr + I810_GPIOB); - return (0 != (readl(ioaddr + I810_GPIOB) & SDA_VAL_IN)); -} - -static void bit_i810ddc_setscl(void *data, int val) -{ - writel((val ? SCL_VAL_OUT : 0) | SCL_DIR | SCL_DIR_MASK | SCL_VAL_MASK, - ioaddr + I810_GPIOA); - readl(ioaddr + I810_GPIOA); /* flush posted write */ -} - -static void bit_i810ddc_setsda(void *data, int val) -{ - writel((val ? SDA_VAL_OUT : 0) | SDA_DIR | SDA_DIR_MASK | SDA_VAL_MASK, - ioaddr + I810_GPIOA); - readl(ioaddr + I810_GPIOA); /* flush posted write */ -} - -static int bit_i810ddc_getscl(void *data) -{ - writel(SCL_DIR_MASK, ioaddr + I810_GPIOA); - writel(0, ioaddr + I810_GPIOA); - return (0 != (readl(ioaddr + I810_GPIOA) & SCL_VAL_IN)); -} - -static int bit_i810ddc_getsda(void *data) -{ - writel(SDA_DIR_MASK, ioaddr + I810_GPIOA); - writel(0, ioaddr + I810_GPIOA); - return (0 != (readl(ioaddr + I810_GPIOA) & SDA_VAL_IN)); -} - -static int config_i810(struct pci_dev *dev) -{ - unsigned long cadr; - - /* map I810 memory */ - cadr = dev->resource[1].start; - cadr += I810_IOCONTROL_OFFSET; - cadr &= PCI_BASE_ADDRESS_MEM_MASK; - ioaddr = ioremap_nocache(cadr, 0x1000); - if (ioaddr) { - bit_i810i2c_setscl(NULL, 1); - bit_i810i2c_setsda(NULL, 1); - bit_i810ddc_setscl(NULL, 1); - bit_i810ddc_setsda(NULL, 1); - return 0; - } - return -ENODEV; -} - -static struct i2c_algo_bit_data i810_i2c_bit_data = { - .setsda = bit_i810i2c_setsda, - .setscl = bit_i810i2c_setscl, - .getsda = bit_i810i2c_getsda, - .getscl = bit_i810i2c_getscl, - .udelay = CYCLE_DELAY, - .timeout = TIMEOUT, -}; - -static struct i2c_adapter i810_i2c_adapter = { - .owner = THIS_MODULE, - .id = I2C_HW_B_I810, - .name = "I810/I815 I2C Adapter", - .algo_data = &i810_i2c_bit_data, -}; - -static struct i2c_algo_bit_data i810_ddc_bit_data = { - .setsda = bit_i810ddc_setsda, - .setscl = bit_i810ddc_setscl, - .getsda = bit_i810ddc_getsda, - .getscl = bit_i810ddc_getscl, - .udelay = CYCLE_DELAY, - .timeout = TIMEOUT, -}; - -static struct i2c_adapter i810_ddc_adapter = { - .owner = THIS_MODULE, - .id = I2C_HW_B_I810, - .name = "I810/I815 DDC Adapter", - .algo_data = &i810_ddc_bit_data, -}; - -static struct pci_device_id i810_ids[] __devinitdata = { - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG1) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810E_IG) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_IG) }, - { 0, }, -}; - -MODULE_DEVICE_TABLE (pci, i810_ids); - -static int __devinit i810_probe(struct pci_dev *dev, const struct pci_device_id *id) -{ - int retval; - - retval = config_i810(dev); - if (retval) - return retval; - dev_info(&dev->dev, "i810/i815 i2c device found.\n"); - - /* set up the sysfs linkage to our parent device */ - i810_i2c_adapter.dev.parent = &dev->dev; - i810_ddc_adapter.dev.parent = &dev->dev; - - retval = i2c_bit_add_bus(&i810_i2c_adapter); - if (retval) - return retval; - retval = i2c_bit_add_bus(&i810_ddc_adapter); - if (retval) - i2c_del_adapter(&i810_i2c_adapter); - return retval; -} - -static void __devexit i810_remove(struct pci_dev *dev) -{ - i2c_del_adapter(&i810_ddc_adapter); - i2c_del_adapter(&i810_i2c_adapter); - iounmap(ioaddr); -} - -static struct pci_driver i810_driver = { - .name = "i810_smbus", - .id_table = i810_ids, - .probe = i810_probe, - .remove = __devexit_p(i810_remove), -}; - -static int __init i2c_i810_init(void) -{ - return pci_register_driver(&i810_driver); -} - -static void __exit i2c_i810_exit(void) -{ - pci_unregister_driver(&i810_driver); -} - -MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>, " - "Philip Edelbrock <phil@netroedge.com>, " - "Ralph Metzler <rjkm@thp.uni-koeln.de>, " - "and Mark D. Studebaker <mdsxyz123@yahoo.com>"); -MODULE_DESCRIPTION("I810/I815 I2C/DDC driver"); -MODULE_LICENSE("GPL"); - -module_init(i2c_i810_init); -module_exit(i2c_i810_exit); |