diff options
Diffstat (limited to 'drivers/i2c/busses/i2c-intel-mid.c')
| -rw-r--r-- | drivers/i2c/busses/i2c-intel-mid.c | 14 |
1 files changed, 7 insertions, 7 deletions
diff --git a/drivers/i2c/busses/i2c-intel-mid.c b/drivers/i2c/busses/i2c-intel-mid.c index c71492782bb..e828ac85cfa 100644 --- a/drivers/i2c/busses/i2c-intel-mid.c +++ b/drivers/i2c/busses/i2c-intel-mid.c @@ -170,8 +170,8 @@ struct intel_mid_i2c_private { /* Raw Interrupt Status Register */ #define IC_RAW_INTR_STAT 0x34 /* Read Only */ #define GEN_CALL (1 << 11) /* General call */ -#define START_DET (1 << 10) /* (RE)START occured */ -#define STOP_DET (1 << 9) /* STOP occured */ +#define START_DET (1 << 10) /* (RE)START occurred */ +#define STOP_DET (1 << 9) /* STOP occurred */ #define ACTIVITY (1 << 8) /* Bus busy */ #define RX_DONE (1 << 7) /* Not used in Master mode */ #define TX_ABRT (1 << 6) /* Transmit Abort */ @@ -375,7 +375,7 @@ static int intel_mid_i2c_disable(struct i2c_adapter *adap) * I2C should be disabled prior to other register operation. If failed, an * errno is returned. Mask and Clear all interrpts, this should be done at * first. Set common registers which will not be modified during normal - * transfers, including: controll register, FIFO threshold and clock freq. + * transfers, including: control register, FIFO threshold and clock freq. * Check APB data width at last. */ static int intel_mid_i2c_hwinit(struct intel_mid_i2c_private *i2c) @@ -455,7 +455,7 @@ static inline bool intel_mid_i2c_address_neq(const struct i2c_msg *p1, * * By reading register IC_TX_ABRT_SOURCE, various transfer errors can be * distingushed. At present, no circumstances have been found out that - * multiple errors would be occured simutaneously, so we simply use the + * multiple errors would be occurred simutaneously, so we simply use the * register value directly. * * At last the error bits are cleared. (Note clear ABRT_SBYTE_NORSTRT bit need @@ -469,7 +469,7 @@ static void intel_mid_i2c_abort(struct intel_mid_i2c_private *i2c) /* Single transfer error check: * According to databook, TX/RX FIFOs would be flushed when - * the abort interrupt occured. + * the abort interrupt occurred. */ if (abort & ABRT_MASTER_DIS) dev_err(&adap->dev, @@ -569,7 +569,7 @@ static int xfer_read(struct i2c_adapter *adap, unsigned char *buf, int length) * Return Values: * 0 if the read transfer succeeds * -ETIMEDOUT if we cannot read the "raw" interrupt register - * -EINVAL if a transfer abort occured + * -EINVAL if a transfer abort occurred * * For every byte, a "WRITE" command will be loaded into IC_DATA_CMD prior to * data transfer. The actual "write" operation will be performed when the @@ -697,7 +697,7 @@ static int intel_mid_i2c_setup(struct i2c_adapter *adap, struct i2c_msg *pmsg) * @num: number of i2c_msg * * Return Values: - * + number of messages transfered + * + number of messages transferred * -ETIMEDOUT If cannot disable I2C controller or read IC_STATUS * -EINVAL If the address in i2c_msg is invalid * |