diff options
Diffstat (limited to 'drivers/i2c/busses/i2c-s3c2410.c')
| -rw-r--r-- | drivers/i2c/busses/i2c-s3c2410.c | 37 |
1 files changed, 33 insertions, 4 deletions
diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index 8162901ff75..ae4491062e4 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -601,6 +601,31 @@ static irqreturn_t s3c24xx_i2c_irq(int irqno, void *dev_id) return IRQ_HANDLED; } +/* + * Disable the bus so that we won't get any interrupts from now on, or try + * to drive any lines. This is the default state when we don't have + * anything to send/receive. + * + * If there is an event on the bus, or we have a pre-existing event at + * kernel boot time, we may not notice the event and the I2C controller + * will lock the bus with the I2C clock line low indefinitely. + */ +static inline void s3c24xx_i2c_disable_bus(struct s3c24xx_i2c *i2c) +{ + unsigned long tmp; + + /* Stop driving the I2C pins */ + tmp = readl(i2c->regs + S3C2410_IICSTAT); + tmp &= ~S3C2410_IICSTAT_TXRXEN; + writel(tmp, i2c->regs + S3C2410_IICSTAT); + + /* We don't expect any interrupts now, and don't want send acks */ + tmp = readl(i2c->regs + S3C2410_IICCON); + tmp &= ~(S3C2410_IICCON_IRQEN | S3C2410_IICCON_IRQPEND | + S3C2410_IICCON_ACKEN); + writel(tmp, i2c->regs + S3C2410_IICCON); +} + /* s3c24xx_i2c_set_master * @@ -735,7 +760,11 @@ static int s3c24xx_i2c_doxfer(struct s3c24xx_i2c *i2c, s3c24xx_i2c_wait_idle(i2c); + s3c24xx_i2c_disable_bus(i2c); + out: + i2c->state = STATE_IDLE; + return ret; } @@ -1004,7 +1033,6 @@ static void s3c24xx_i2c_dt_gpio_free(struct s3c24xx_i2c *i2c) static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) { - unsigned long iicon = S3C2410_IICCON_IRQEN | S3C2410_IICCON_ACKEN; struct s3c2410_platform_i2c *pdata; unsigned int freq; @@ -1018,12 +1046,12 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) dev_info(i2c->dev, "slave address 0x%02x\n", pdata->slave_addr); - writel(iicon, i2c->regs + S3C2410_IICCON); + writel(0, i2c->regs + S3C2410_IICCON); + writel(0, i2c->regs + S3C2410_IICSTAT); /* we need to work out the divisors for the clock... */ if (s3c24xx_i2c_clockrate(i2c, &freq) != 0) { - writel(0, i2c->regs + S3C2410_IICCON); dev_err(i2c->dev, "cannot meet bus frequency required\n"); return -EINVAL; } @@ -1031,7 +1059,8 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) /* todo - check that the i2c lines aren't being dragged anywhere */ dev_info(i2c->dev, "bus frequency set to %d KHz\n", freq); - dev_dbg(i2c->dev, "S3C2410_IICCON=0x%02lx\n", iicon); + dev_dbg(i2c->dev, "S3C2410_IICCON=0x%02x\n", + readl(i2c->regs + S3C2410_IICCON)); return 0; } |