diff options
Diffstat (limited to 'drivers/i2c/chips')
| -rw-r--r-- | drivers/i2c/chips/Kconfig | 15 | ||||
| -rw-r--r-- | drivers/i2c/chips/Makefile | 1 | ||||
| -rw-r--r-- | drivers/i2c/chips/max6875.c | 246 |
3 files changed, 0 insertions, 262 deletions
diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 8f8c81eb0ae..02d746c9c47 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -64,21 +64,6 @@ config SENSORS_PCA9539 This driver is deprecated and will be dropped soon. Use drivers/gpio/pca953x.c instead. -config SENSORS_MAX6875 - tristate "Maxim MAX6875 Power supply supervisor" - depends on EXPERIMENTAL - help - If you say yes here you get support for the Maxim MAX6875 - EEPROM-programmable, quad power-supply sequencer/supervisor. - - This provides an interface to program the EEPROM and reset the chip. - - This driver also supports the Maxim MAX6874 hex power-supply - sequencer/supervisor if found at a compatible address. - - This driver can also be built as a module. If so, the module - will be called max6875. - config SENSORS_TSL2550 tristate "Taos TSL2550 ambient light sensor" depends on EXPERIMENTAL diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index 55a37603718..f4680d16ee3 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,7 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_SENSORS_MAX6875) += max6875.o obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o obj-$(CONFIG_PCF8575) += pcf8575.o diff --git a/drivers/i2c/chips/max6875.c b/drivers/i2c/chips/max6875.c deleted file mode 100644 index 033d9d81ec8..00000000000 --- a/drivers/i2c/chips/max6875.c +++ /dev/null @@ -1,246 +0,0 @@ -/* - max6875.c - driver for MAX6874/MAX6875 - - Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com> - - Based on i2c/chips/eeprom.c - - The MAX6875 has a bank of registers and two banks of EEPROM. - Address ranges are defined as follows: - * 0x0000 - 0x0046 = configuration registers - * 0x8000 - 0x8046 = configuration EEPROM - * 0x8100 - 0x82FF = user EEPROM - - This driver makes the user EEPROM available for read. - - The registers & config EEPROM should be accessed via i2c-dev. - - The MAX6875 ignores the lowest address bit, so each chip responds to - two addresses - 0x50/0x51 and 0x52/0x53. - - Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read - address, so this driver is destructive if loaded for the wrong EEPROM chip. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; version 2 of the License. -*/ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/module.h> -#include <linux/slab.h> -#include <linux/i2c.h> -#include <linux/mutex.h> - -/* Do not scan - the MAX6875 access method will write to some EEPROM chips */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(max6875); - -/* The MAX6875 can only read/write 16 bytes at a time */ -#define SLICE_SIZE 16 -#define SLICE_BITS 4 - -/* USER EEPROM is at addresses 0x8100 - 0x82FF */ -#define USER_EEPROM_BASE 0x8100 -#define USER_EEPROM_SIZE 0x0200 -#define USER_EEPROM_SLICES 32 - -/* MAX6875 commands */ -#define MAX6875_CMD_BLK_READ 0x84 - -/* Each client has this additional data */ -struct max6875_data { - struct i2c_client *fake_client; - struct mutex update_lock; - - u32 valid; - u8 data[USER_EEPROM_SIZE]; - unsigned long last_updated[USER_EEPROM_SLICES]; -}; - -static void max6875_update_slice(struct i2c_client *client, int slice) -{ - struct max6875_data *data = i2c_get_clientdata(client); - int i, j, addr; - u8 *buf; - - if (slice >= USER_EEPROM_SLICES) - return; - - mutex_lock(&data->update_lock); - - buf = &data->data[slice << SLICE_BITS]; - - if (!(data->valid & (1 << slice)) || - time_after(jiffies, data->last_updated[slice])) { - - dev_dbg(&client->dev, "Starting update of slice %u\n", slice); - - data->valid &= ~(1 << slice); - - addr = USER_EEPROM_BASE + (slice << SLICE_BITS); - - /* select the eeprom address */ - if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) { - dev_err(&client->dev, "address set failed\n"); - goto exit_up; - } - - if (i2c_check_functionality(client->adapter, - I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { - if (i2c_smbus_read_i2c_block_data(client, - MAX6875_CMD_BLK_READ, - SLICE_SIZE, - buf) != SLICE_SIZE) { - goto exit_up; - } - } else { - for (i = 0; i < SLICE_SIZE; i++) { - j = i2c_smbus_read_byte(client); - if (j < 0) { - goto exit_up; - } - buf[i] = j; - } - } - data->last_updated[slice] = jiffies; - data->valid |= (1 << slice); - } -exit_up: - mutex_unlock(&data->update_lock); -} - -static ssize_t max6875_read(struct kobject *kobj, - struct bin_attribute *bin_attr, - char *buf, loff_t off, size_t count) -{ - struct i2c_client *client = kobj_to_i2c_client(kobj); - struct max6875_data *data = i2c_get_clientdata(client); - int slice, max_slice; - - if (off > USER_EEPROM_SIZE) - return 0; - - if (off + count > USER_EEPROM_SIZE) - count = USER_EEPROM_SIZE - off; - - /* refresh slices which contain requested bytes */ - max_slice = (off + count - 1) >> SLICE_BITS; - for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++) - max6875_update_slice(client, slice); - - memcpy(buf, &data->data[off], count); - - return count; -} - -static struct bin_attribute user_eeprom_attr = { - .attr = { - .name = "eeprom", - .mode = S_IRUGO, - }, - .size = USER_EEPROM_SIZE, - .read = max6875_read, -}; - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int max6875_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA - | I2C_FUNC_SMBUS_READ_BYTE)) - return -ENODEV; - - /* Only check even addresses */ - if (client->addr & 1) - return -ENODEV; - - strlcpy(info->type, "max6875", I2C_NAME_SIZE); - - return 0; -} - -static int max6875_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct max6875_data *data; - int err; - - if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL))) - return -ENOMEM; - - /* A fake client is created on the odd address */ - data->fake_client = i2c_new_dummy(client->adapter, client->addr + 1); - if (!data->fake_client) { - err = -ENOMEM; - goto exit_kfree; - } - - /* Init real i2c_client */ - i2c_set_clientdata(client, data); - mutex_init(&data->update_lock); - - err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr); - if (err) - goto exit_remove_fake; - - return 0; - -exit_remove_fake: - i2c_unregister_device(data->fake_client); -exit_kfree: - kfree(data); - return err; -} - -static int max6875_remove(struct i2c_client *client) -{ - struct max6875_data *data = i2c_get_clientdata(client); - - i2c_unregister_device(data->fake_client); - - sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr); - kfree(data); - - return 0; -} - -static const struct i2c_device_id max6875_id[] = { - { "max6875", 0 }, - { } -}; - -static struct i2c_driver max6875_driver = { - .driver = { - .name = "max6875", - }, - .probe = max6875_probe, - .remove = max6875_remove, - .id_table = max6875_id, - - .detect = max6875_detect, - .address_data = &addr_data, -}; - -static int __init max6875_init(void) -{ - return i2c_add_driver(&max6875_driver); -} - -static void __exit max6875_exit(void) -{ - i2c_del_driver(&max6875_driver); -} - - -MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>"); -MODULE_DESCRIPTION("MAX6875 driver"); -MODULE_LICENSE("GPL"); - -module_init(max6875_init); -module_exit(max6875_exit); |