diff options
Diffstat (limited to 'drivers/i2c')
35 files changed, 3242 insertions, 315 deletions
diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig index 8d8a00e5a30..02ce9cff5fc 100644 --- a/drivers/i2c/Kconfig +++ b/drivers/i2c/Kconfig @@ -61,6 +61,16 @@ config I2C_HELPER_AUTO In doubt, say Y. +config I2C_SMBUS + tristate "SMBus-specific protocols" if !I2C_HELPER_AUTO + help + Say Y here if you want support for SMBus extensions to the I2C + specification. At the moment, the only supported extension is + the SMBus alert protocol. + + This support is also available as a module. If so, the module + will be called i2c-smbus. + source drivers/i2c/algos/Kconfig source drivers/i2c/busses/Kconfig source drivers/i2c/chips/Kconfig diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index ba26e6cbe74..acd0250c16a 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -4,6 +4,7 @@ obj-$(CONFIG_I2C_BOARDINFO) += i2c-boardinfo.o obj-$(CONFIG_I2C) += i2c-core.o +obj-$(CONFIG_I2C_SMBUS) += i2c-smbus.o obj-$(CONFIG_I2C_CHARDEV) += i2c-dev.o obj-y += busses/ chips/ algos/ diff --git a/drivers/i2c/algos/i2c-algo-pca.c b/drivers/i2c/algos/i2c-algo-pca.c index 78d42aae008..dcdaf8e675b 100644 --- a/drivers/i2c/algos/i2c-algo-pca.c +++ b/drivers/i2c/algos/i2c-algo-pca.c @@ -453,8 +453,6 @@ static int pca_init(struct i2c_adapter *adap) */ int raise_fall_time; - struct i2c_algo_pca_data *pca_data = adap->algo_data; - /* Ignore the reset function from the module, * we can use the parallel bus reset */ diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 5f318ce2977..9c6170cd9aa 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -77,7 +77,7 @@ config I2C_AMD8111 will be called i2c-amd8111. config I2C_I801 - tristate "Intel 82801 (ICH)" + tristate "Intel 82801 (ICH/PCH)" depends on PCI help If you say yes to this option, support will be included for the Intel @@ -97,7 +97,8 @@ config I2C_I801 ICH9 Tolapai ICH10 - PCH + 3400/5 Series (PCH) + Cougar Point (PCH) This driver can also be built as a module. If so, the module will be called i2c-i801. @@ -105,6 +106,8 @@ config I2C_I801 config I2C_ISCH tristate "Intel SCH SMBus 1.0" depends on PCI + select MFD_CORE + select LPC_SCH help Say Y here if you want to use SMBus controller on the Intel SCH based systems. @@ -418,13 +421,12 @@ config I2C_IXP2000 instead. config I2C_MPC - tristate "MPC107/824x/85xx/52xx/86xx" + tristate "MPC107/824x/85xx/512x/52xx/83xx/86xx" depends on PPC32 help If you say yes to this option, support will be included for the - built-in I2C interface on the MPC107/Tsi107/MPC8240/MPC8245 and - MPC85xx/MPC8641 family processors. The driver may also work on 52xx - family processors, though interrupts are known not to work. + built-in I2C interface on the MPC107, Tsi107, MPC512x, MPC52xx, + MPC8240, MPC8245, MPC83xx, MPC85xx and MPC8641 family processors. This driver can also be built as a module. If so, the module will be called i2c-mpc. @@ -439,6 +441,13 @@ config I2C_MV64XXX This driver can also be built as a module. If so, the module will be called i2c-mv64xxx. +config I2C_NOMADIK + tristate "ST-Ericsson Nomadik/Ux500 I2C Controller" + depends on PLAT_NOMADIK + help + If you say yes to this option, support will be included for the + I2C interface from ST-Ericsson's Nomadik and Ux500 architectures. + config I2C_OCORES tristate "OpenCores I2C Controller" depends on EXPERIMENTAL @@ -564,12 +573,33 @@ config I2C_VERSATILE This driver can also be built as a module. If so, the module will be called i2c-versatile. +config I2C_OCTEON + tristate "Cavium OCTEON I2C bus support" + depends on CPU_CAVIUM_OCTEON + help + Say yes if you want to support the I2C serial bus on Cavium + OCTEON SOC. + + This driver can also be built as a module. If so, the module + will be called i2c-octeon. + +config I2C_XILINX + tristate "Xilinx I2C Controller" + depends on EXPERIMENTAL && HAS_IOMEM + help + If you say yes to this option, support will be included for the + Xilinx I2C controller. + + This driver can also be built as a module. If so, the module + will be called xilinx_i2c. + comment "External I2C/SMBus adapter drivers" config I2C_PARPORT tristate "Parallel port adapter" depends on PARPORT select I2C_ALGOBIT + select I2C_SMBUS help This supports parallel port I2C adapters such as the ones made by Philips or Velleman, Analog Devices evaluation boards, and more. @@ -593,6 +623,7 @@ config I2C_PARPORT config I2C_PARPORT_LIGHT tristate "Parallel port adapter (light)" select I2C_ALGOBIT + select I2C_SMBUS help This supports parallel port I2C adapters such as the ones made by Philips or Velleman, Analog Devices evaluation boards, and more. diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index 302c551977b..097236f631e 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -42,6 +42,7 @@ obj-$(CONFIG_I2C_IOP3XX) += i2c-iop3xx.o obj-$(CONFIG_I2C_IXP2000) += i2c-ixp2000.o obj-$(CONFIG_I2C_MPC) += i2c-mpc.o obj-$(CONFIG_I2C_MV64XXX) += i2c-mv64xxx.o +obj-$(CONFIG_I2C_NOMADIK) += i2c-nomadik.o obj-$(CONFIG_I2C_OCORES) += i2c-ocores.o obj-$(CONFIG_I2C_OMAP) += i2c-omap.o obj-$(CONFIG_I2C_PASEMI) += i2c-pasemi.o @@ -54,6 +55,8 @@ obj-$(CONFIG_I2C_SH_MOBILE) += i2c-sh_mobile.o obj-$(CONFIG_I2C_SIMTEC) += i2c-simtec.o obj-$(CONFIG_I2C_STU300) += i2c-stu300.o obj-$(CONFIG_I2C_VERSATILE) += i2c-versatile.o +obj-$(CONFIG_I2C_OCTEON) += i2c-octeon.o +obj-$(CONFIG_I2C_XILINX) += i2c-xiic.o # External I2C/SMBus adapter drivers obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o diff --git a/drivers/i2c/busses/i2c-ali1535.c b/drivers/i2c/busses/i2c-ali1535.c index 8de7d7b87bb..bd8f1e4d9e6 100644 --- a/drivers/i2c/busses/i2c-ali1535.c +++ b/drivers/i2c/busses/i2c-ali1535.c @@ -480,7 +480,7 @@ static struct i2c_adapter ali1535_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id ali1535_ids[] = { +static const struct pci_device_id ali1535_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101) }, { }, }; diff --git a/drivers/i2c/busses/i2c-ali1563.c b/drivers/i2c/busses/i2c-ali1563.c index 4687af40dd5..a409cfcf062 100644 --- a/drivers/i2c/busses/i2c-ali1563.c +++ b/drivers/i2c/busses/i2c-ali1563.c @@ -417,7 +417,7 @@ static void __devexit ali1563_remove(struct pci_dev * dev) ali1563_shutdown(dev); } -static struct pci_device_id __devinitdata ali1563_id_table[] = { +static const struct pci_device_id ali1563_id_table[] __devinitconst = { { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1563) }, {}, }; diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c index e7e3205f128..659f63f5e4a 100644 --- a/drivers/i2c/busses/i2c-ali15x3.c +++ b/drivers/i2c/busses/i2c-ali15x3.c @@ -477,7 +477,7 @@ static struct i2c_adapter ali15x3_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id ali15x3_ids[] = { +static const struct pci_device_id ali15x3_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-amd756.c b/drivers/i2c/busses/i2c-amd756.c index 8f0b90ef8c7..c5a9fa488e7 100644 --- a/drivers/i2c/busses/i2c-amd756.c +++ b/drivers/i2c/busses/i2c-amd756.c @@ -308,7 +308,7 @@ static const char* chipname[] = { "nVidia nForce", "AMD8111", }; -static struct pci_device_id amd756_ids[] = { +static const struct pci_device_id amd756_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_740B), .driver_data = AMD756 }, { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7413), diff --git a/drivers/i2c/busses/i2c-amd8111.c b/drivers/i2c/busses/i2c-amd8111.c index 5b4ad86ca16..d0dc970d737 100644 --- a/drivers/i2c/busses/i2c-amd8111.c +++ b/drivers/i2c/busses/i2c-amd8111.c @@ -351,7 +351,7 @@ static const struct i2c_algorithm smbus_algorithm = { }; -static struct pci_device_id amd8111_ids[] = { +static const struct pci_device_id amd8111_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS2) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c index 9e18ef97f15..3e72b69aa7f 100644 --- a/drivers/i2c/busses/i2c-designware.c +++ b/drivers/i2c/busses/i2c-designware.c @@ -497,13 +497,13 @@ static int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev) int i; if (abort_source & DW_IC_TX_ABRT_NOACK) { - for_each_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) + for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) dev_dbg(dev->dev, "%s: %s\n", __func__, abort_sources[i]); return -EREMOTEIO; } - for_each_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) + for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) dev_err(dev->dev, "%s: %s\n", __func__, abort_sources[i]); if (abort_source & DW_IC_TX_ARB_LOST) diff --git a/drivers/i2c/busses/i2c-hydra.c b/drivers/i2c/busses/i2c-hydra.c index bec9b845dd1..c767295ad1f 100644 --- a/drivers/i2c/busses/i2c-hydra.c +++ b/drivers/i2c/busses/i2c-hydra.c @@ -105,7 +105,7 @@ static struct i2c_adapter hydra_adap = { .algo_data = &hydra_bit_data, }; -static struct pci_device_id hydra_ids[] = { +static const struct pci_device_id hydra_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_APPLE, PCI_DEVICE_ID_APPLE_HYDRA) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index df6ab553f97..9da5b05cdb5 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -41,7 +41,8 @@ Tolapai 0x5032 32 hard yes yes yes ICH10 0x3a30 32 hard yes yes yes ICH10 0x3a60 32 hard yes yes yes - PCH 0x3b30 32 hard yes yes yes + 3400/5 Series (PCH) 0x3b30 32 hard yes yes yes + Cougar Point (PCH) 0x1c22 32 hard yes yes yes Features supported by this driver: Software PEC no @@ -561,7 +562,7 @@ static struct i2c_adapter i801_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id i801_ids[] = { +static const struct pci_device_id i801_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_3) }, { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_3) }, { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_2) }, @@ -578,6 +579,7 @@ static struct pci_device_id i801_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_4) }, { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_5) }, { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PCH_SMBUS) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CPT_SMBUS) }, { 0, } }; @@ -707,6 +709,7 @@ static int __devinit i801_probe(struct pci_dev *dev, const struct pci_device_id case PCI_DEVICE_ID_INTEL_ICH10_4: case PCI_DEVICE_ID_INTEL_ICH10_5: case PCI_DEVICE_ID_INTEL_PCH_SMBUS: + case PCI_DEVICE_ID_INTEL_CPT_SMBUS: i801_features |= FEATURE_I2C_BLOCK_READ; /* fall through */ case PCI_DEVICE_ID_INTEL_82801DB_3: diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c index 75bf820e7cc..32375bddae7 100644 --- a/drivers/i2c/busses/i2c-imx.c +++ b/drivers/i2c/busses/i2c-imx.c @@ -627,7 +627,6 @@ static int __exit i2c_imx_remove(struct platform_device *pdev) } static struct platform_driver i2c_imx_driver = { - .probe = i2c_imx_probe, .remove = __exit_p(i2c_imx_remove), .driver = { .name = DRIVER_NAME, diff --git a/drivers/i2c/busses/i2c-isch.c b/drivers/i2c/busses/i2c-isch.c index dba6eb053e2..ddc258edb34 100644 --- a/drivers/i2c/busses/i2c-isch.c +++ b/drivers/i2c/busses/i2c-isch.c @@ -27,7 +27,7 @@ */ #include <linux/module.h> -#include <linux/pci.h> +#include <linux/platform_device.h> #include <linux/kernel.h> #include <linux/delay.h> #include <linux/stddef.h> @@ -46,12 +46,6 @@ #define SMBHSTDAT1 (7 + sch_smba) #define SMBBLKDAT (0x20 + sch_smba) -/* count for request_region */ -#define SMBIOSIZE 64 - -/* PCI Address Constants */ -#define SMBBA_SCH 0x40 - /* Other settings */ #define MAX_TIMEOUT 500 @@ -63,7 +57,6 @@ #define SCH_BLOCK_DATA 0x05 static unsigned short sch_smba; -static struct pci_driver sch_driver; static struct i2c_adapter sch_adapter; /* @@ -256,37 +249,23 @@ static struct i2c_adapter sch_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id sch_ids[] = { - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC) }, - { 0, } -}; - -MODULE_DEVICE_TABLE(pci, sch_ids); - -static int __devinit sch_probe(struct pci_dev *dev, - const struct pci_device_id *id) +static int __devinit smbus_sch_probe(struct platform_device *dev) { + struct resource *res; int retval; - unsigned int smba; - pci_read_config_dword(dev, SMBBA_SCH, &smba); - if (!(smba & (1 << 31))) { - dev_err(&dev->dev, "SMBus I/O space disabled!\n"); - return -ENODEV; - } + res = platform_get_resource(dev, IORESOURCE_IO, 0); + if (!res) + return -EBUSY; - sch_smba = (unsigned short)smba; - if (sch_smba == 0) { - dev_err(&dev->dev, "SMBus base address uninitialized!\n"); - return -ENODEV; - } - if (acpi_check_region(sch_smba, SMBIOSIZE, sch_driver.name)) - return -ENODEV; - if (!request_region(sch_smba, SMBIOSIZE, sch_driver.name)) { + if (!request_region(res->start, resource_size(res), dev->name)) { dev_err(&dev->dev, "SMBus region 0x%x already in use!\n", sch_smba); return -EBUSY; } + + sch_smba = res->start; + dev_dbg(&dev->dev, "SMBA = 0x%X\n", sch_smba); /* set up the sysfs linkage to our parent device */ @@ -298,37 +277,43 @@ static int __devinit sch_probe(struct pci_dev *dev, retval = i2c_add_adapter(&sch_adapter); if (retval) { dev_err(&dev->dev, "Couldn't register adapter!\n"); - release_region(sch_smba, SMBIOSIZE); + release_region(res->start, resource_size(res)); sch_smba = 0; } return retval; } -static void __devexit sch_remove(struct pci_dev *dev) +static int __devexit smbus_sch_remove(struct platform_device *pdev) { + struct resource *res; if (sch_smba) { i2c_del_adapter(&sch_adapter); - release_region(sch_smba, SMBIOSIZE); + res = platform_get_resource(pdev, IORESOURCE_IO, 0); + release_region(res->start, resource_size(res)); sch_smba = 0; } + + return 0; } -static struct pci_driver sch_driver = { - .name = "isch_smbus", - .id_table = sch_ids, - .probe = sch_probe, - .remove = __devexit_p(sch_remove), +static struct platform_driver smbus_sch_driver = { + .driver = { + .name = "isch_smbus", + .owner = THIS_MODULE, + }, + .probe = smbus_sch_probe, + .remove = __devexit_p(smbus_sch_remove), }; static int __init i2c_sch_init(void) { - return pci_register_driver(&sch_driver); + return platform_driver_register(&smbus_sch_driver); } static void __exit i2c_sch_exit(void) { - pci_unregister_driver(&sch_driver); + platform_driver_unregister(&smbus_sch_driver); } MODULE_AUTHOR("Jacob Pan <jacob.jun.pan@intel.com>"); @@ -337,3 +322,4 @@ MODULE_LICENSE("GPL"); module_init(i2c_sch_init); module_exit(i2c_sch_exit); +MODULE_ALIAS("platform:isch_smbus"); diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c index f627001108b..78a15af3294 100644 --- a/drivers/i2c/busses/i2c-mpc.c +++ b/drivers/i2c/busses/i2c-mpc.c @@ -31,6 +31,9 @@ #define DRV_NAME "mpc-i2c" +#define MPC_I2C_CLOCK_LEGACY 0 +#define MPC_I2C_CLOCK_PRESERVE (~0U) + #define MPC_I2C_FDR 0x04 #define MPC_I2C_CR 0x08 #define MPC_I2C_SR 0x0c @@ -66,10 +69,9 @@ struct mpc_i2c_divider { u16 fdr; /* including dfsrr */ }; -struct mpc_i2c_match_data { - void (*setclock)(struct device_node *node, - struct mpc_i2c *i2c, - u32 clock, u32 prescaler); +struct mpc_i2c_data { + void (*setup)(struct device_node *node, struct mpc_i2c *i2c, + u32 clock, u32 prescaler); u32 prescaler; }; @@ -164,8 +166,8 @@ static int i2c_wait(struct mpc_i2c *i2c, unsigned timeout, int writing) return 0; } -#ifdef CONFIG_PPC_MPC52xx -static const struct mpc_i2c_divider mpc_i2c_dividers_52xx[] = { +#if defined(CONFIG_PPC_MPC52xx) || defined(CONFIG_PPC_MPC512x) +static const struct mpc_i2c_divider mpc_i2c_dividers_52xx[] __devinitconst = { {20, 0x20}, {22, 0x21}, {24, 0x22}, {26, 0x23}, {28, 0x24}, {30, 0x01}, {32, 0x25}, {34, 0x02}, {36, 0x26}, {40, 0x27}, {44, 0x04}, {48, 0x28}, @@ -186,14 +188,15 @@ static const struct mpc_i2c_divider mpc_i2c_dividers_52xx[] = { {10240, 0x9d}, {12288, 0x9e}, {15360, 0x9f} }; -int mpc_i2c_get_fdr_52xx(struct device_node *node, u32 clock, int prescaler) +static int __devinit mpc_i2c_get_fdr_52xx(struct device_node *node, u32 clock, + int prescaler) { const struct mpc_i2c_divider *div = NULL; unsigned int pvr = mfspr(SPRN_PVR); u32 divider; int i; - if (!clock) + if (clock == MPC_I2C_CLOCK_LEGACY) return -EINVAL; /* Determine divider value */ @@ -215,12 +218,18 @@ int mpc_i2c_get_fdr_52xx(struct device_node *node, u32 clock, int prescaler) return div ? (int)div->fdr : -EINVAL; } -static void mpc_i2c_setclock_52xx(struct device_node *node, - struct mpc_i2c *i2c, - u32 clock, u32 prescaler) +static void __devinit mpc_i2c_setup_52xx(struct device_node *node, + struct mpc_i2c *i2c, + u32 clock, u32 prescaler) { int ret, fdr; + if (clock == MPC_I2C_CLOCK_PRESERVE) { + dev_dbg(i2c->dev, "using fdr %d\n", + readb(i2c->base + MPC_I2C_FDR)); + return; + } + ret = mpc_i2c_get_fdr_52xx(node, clock, prescaler); fdr = (ret >= 0) ? ret : 0x3f; /* backward compatibility */ @@ -229,16 +238,52 @@ static void mpc_i2c_setclock_52xx(struct device_node *node, if (ret >= 0) dev_info(i2c->dev, "clock %d Hz (fdr=%d)\n", clock, fdr); } -#else /* !CONFIG_PPC_MPC52xx */ -static void mpc_i2c_setclock_52xx(struct device_node *node, - struct mpc_i2c *i2c, - u32 clock, u32 prescaler) +#else /* !(CONFIG_PPC_MPC52xx || CONFIG_PPC_MPC512x) */ +static void __devinit mpc_i2c_setup_52xx(struct device_node *node, + struct mpc_i2c *i2c, + u32 clock, u32 prescaler) +{ +} +#endif /* CONFIG_PPC_MPC52xx || CONFIG_PPC_MPC512x */ + +#ifdef CONFIG_PPC_MPC512x +static void __devinit mpc_i2c_setup_512x(struct device_node *node, + struct mpc_i2c *i2c, + u32 clock, u32 prescaler) +{ + struct device_node *node_ctrl; + void __iomem *ctrl; + const u32 *pval; + u32 idx; + + /* Enable I2C interrupts for mpc5121 */ + node_ctrl = of_find_compatible_node(NULL, NULL, + "fsl,mpc5121-i2c-ctrl"); + if (node_ctrl) { + ctrl = of_iomap(node_ctrl, 0); + if (ctrl) { + /* Interrupt enable bits for i2c-0/1/2: bit 24/26/28 */ + pval = of_get_property(node, "reg", NULL); + idx = (*pval & 0xff) / 0x20; + setbits32(ctrl, 1 << (24 + idx * 2)); + iounmap(ctrl); + } + of_node_put(node_ctrl); + } + + /* The clock setup for the 52xx works also fine for the 512x */ + mpc_i2c_setup_52xx(node, i2c, clock, prescaler); +} +#else /* CONFIG_PPC_MPC512x */ +static void __devinit mpc_i2c_setup_512x(struct device_node *node, + struct mpc_i2c *i2c, + u32 clock, u32 prescaler) { } -#endif /* CONFIG_PPC_MPC52xx*/ +#endif /* CONFIG_PPC_MPC512x */ #ifdef CONFIG_FSL_SOC -static const struct mpc_i2c_divider mpc_i2c_dividers_8xxx[] = { +static const struct mpc_i2c_divider mpc_i2c_dividers_8xxx[] __devinitconst = { {160, 0x0120}, {192, 0x0121}, {224, 0x0122}, {256, 0x0123}, {288, 0x0100}, {320, 0x0101}, {352, 0x0601}, {384, 0x0102}, {416, 0x0602}, {448, 0x0126}, {480, 0x0103}, {512, 0x0127}, @@ -258,7 +303,7 @@ static const struct mpc_i2c_divider mpc_i2c_dividers_8xxx[] = { {49152, 0x011e}, {61440, 0x011f} }; -u32 mpc_i2c_get_sec_cfg_8xxx(void) +static u32 __devinit mpc_i2c_get_sec_cfg_8xxx(void) { struct device_node *node = NULL; u32 __iomem *reg; @@ -287,13 +332,14 @@ u32 mpc_i2c_get_sec_cfg_8xxx(void) return val; } -int mpc_i2c_get_fdr_8xxx(struct device_node *node, u32 clock, u32 prescaler) +static int __devinit mpc_i2c_get_fdr_8xxx(struct device_node *node, u32 clock, + u32 prescaler) { const struct mpc_i2c_divider *div = NULL; u32 divider; int i; - if (!clock) + if (clock == MPC_I2C_CLOCK_LEGACY) return -EINVAL; /* Determine proper divider value */ @@ -320,12 +366,19 @@ int mpc_i2c_get_fdr_8xxx(struct device_node *node, u32 clock, u32 prescaler) return div ? (int)div->fdr : -EINVAL; } -static void mpc_i2c_setclock_8xxx(struct device_node *node, - struct mpc_i2c *i2c, - u32 clock, u32 prescaler) +static void __devinit mpc_i2c_setup_8xxx(struct device_node *node, + struct mpc_i2c *i2c, + u32 clock, u32 prescaler) { int ret, fdr; + if (clock == MPC_I2C_CLOCK_PRESERVE) { + dev_dbg(i2c->dev, "using dfsrr %d, fdr %d\n", + readb(i2c->base + MPC_I2C_DFSRR), + readb(i2c->base + MPC_I2C_FDR)); + return; + } + ret = mpc_i2c_get_fdr_8xxx(node, clock, prescaler); fdr = (ret >= 0) ? ret : 0x1031; /* backward compatibility */ @@ -338,9 +391,9 @@ static void mpc_i2c_setclock_8xxx(struct device_node *node, } #else /* !CONFIG_FSL_SOC */ -static void mpc_i2c_setclock_8xxx(struct device_node *node, - struct mpc_i2c *i2c, - u32 clock, u32 prescaler) +static void __devinit mpc_i2c_setup_8xxx(struct device_node *node, + struct mpc_i2c *i2c, + u32 clock, u32 prescaler) { } #endif /* CONFIG_FSL_SOC */ @@ -494,7 +547,7 @@ static int __devinit fsl_i2c_probe(struct of_device *op, { struct mpc_i2c *i2c; const u32 *prop; - u32 clock = 0; + u32 clock = MPC_I2C_CLOCK_LEGACY; int result = 0; int plen; @@ -523,21 +576,21 @@ static int __devinit fsl_i2c_probe(struct of_device *op, } } - if (!of_get_property(op->node, "fsl,preserve-clocking", NULL)) { + if (of_get_property(op->node, "fsl,preserve-clocking", NULL)) { + clock = MPC_I2C_CLOCK_PRESERVE; + } else { prop = of_get_property(op->node, "clock-frequency", &plen); if (prop && plen == sizeof(u32)) clock = *prop; + } - if (match->data) { - struct mpc_i2c_match_data *data = - (struct mpc_i2c_match_data *)match->data; - data->setclock(op->node, i2c, clock, data->prescaler); - } else { - /* Backwards compatibility */ - if (of_get_property(op->node, "dfsrr", NULL)) - mpc_i2c_setclock_8xxx(op->node, i2c, - clock, 0); - } + if (match->data) { + struct mpc_i2c_data *data = match->data; + data->setup(op->node, i2c, clock, data->prescaler); + } else { + /* Backwards compatibility */ + if (of_get_property(op->node, "dfsrr", NULL)) + mpc_i2c_setup_8xxx(op->node, i2c, clock, 0); } dev_set_drvdata(&op->dev, i2c); @@ -582,47 +635,42 @@ static int __devexit fsl_i2c_remove(struct of_device *op) return 0; }; +static struct mpc_i2c_data mpc_i2c_data_512x __devinitdata = { + .setup = mpc_i2c_setup_512x, +}; + +static struct mpc_i2c_data mpc_i2c_data_52xx __devinitdata = { + .setup = mpc_i2c_setup_52xx, +}; + +static struct mpc_i2c_data mpc_i2c_data_8313 __devinitdata = { + .setup = mpc_i2c_setup_8xxx, +}; + +static struct mpc_i2c_data mpc_i2c_data_8543 __devinitdata = { + .setup = mpc_i2c_setup_8xxx, + .prescaler = 2, +}; + +static struct mpc_i2c_data mpc_i2c_data_8544 __devinitdata = { + .setup = mpc_i2c_setup_8xxx, + .prescaler = 3, +}; + static const struct of_device_id mpc_i2c_of_match[] = { - {.compatible = "mpc5200-i2c", - .data = &(struct mpc_i2c_match_data) { - .setclock = mpc_i2c_setclock_52xx, - }, - }, - {.compatible = "fsl,mpc5200b-i2c", - .data = &(struct mpc_i2c_match_data) { - .setclock = mpc_i2c_setclock_52xx, - }, - }, - {.compatible = "fsl,mpc5200-i2c", - .data = &(struct mpc_i2c_match_data) { - .setclock = mpc_i2c_setclock_52xx, - }, - }, - {.compatible = "fsl,mpc8313-i2c", - .data = &(struct mpc_i2c_match_data) { - .setclock = mpc_i2c_setclock_8xxx, - }, - }, - {.compatible = "fsl,mpc8543-i2c", - .data = &(struct mpc_i2c_match_data) { - .setclock = mpc_i2c_setclock_8xxx, - .prescaler = 2, - }, - }, - {.compatible = "fsl,mpc8544-i2c", - .data = &(struct mpc_i2c_match_data) { - .setclock = mpc_i2c_setclock_8xxx, - .prescaler = 3, - }, + {.compatible = "mpc5200-i2c", .data = &mpc_i2c_data_52xx, }, + {.compatible = "fsl,mpc5200b-i2c", .data = &mpc_i2c_data_52xx, }, + {.compatible = "fsl,mpc5200-i2c", .data = &mpc_i2c_data_52xx, }, + {.compatible = "fsl,mpc5121-i2c", .data = &mpc_i2c_data_512x, }, + {.compatible = "fsl,mpc8313-i2c", .data = &mpc_i2c_data_8313, }, + {.compatible = "fsl,mpc8543-i2c", .data = &mpc_i2c_data_8543, }, + {.compatible = "fsl,mpc8544-i2c", .data = &mpc_i2c_data_8544, }, /* Backward compatibility */ - }, {.compatible = "fsl-i2c", }, {}, }; - MODULE_DEVICE_TABLE(of, mpc_i2c_of_match); - /* Structure for a device driver */ static struct of_platform_driver mpc_i2c_driver = { .match_table = mpc_i2c_of_match, @@ -655,5 +703,5 @@ module_exit(fsl_i2c_exit); MODULE_AUTHOR("Adrian Cox <adrian@humboldt.co.uk>"); MODULE_DESCRIPTION("I2C-Bus adapter for MPC107 bridge and " - "MPC824x/85xx/52xx processors"); + "MPC824x/83xx/85xx/86xx/512x/52xx processors"); MODULE_LICENSE("GPL"); diff --git a/drivers/i2c/busses/i2c-nforce2.c b/drivers/i2c/busses/i2c-nforce2.c index ec11d1c4e77..4a700587ef1 100644 --- a/drivers/i2c/busses/i2c-nforce2.c +++ b/drivers/i2c/busses/i2c-nforce2.c @@ -308,7 +308,7 @@ static struct i2c_algorithm smbus_algorithm = { }; -static struct pci_device_id nforce2_ids[] = { +static const struct pci_device_id nforce2_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_SMBUS) }, diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c new file mode 100644 index 00000000000..a15f731fa45 --- /dev/null +++ b/drivers/i2c/busses/i2c-nomadik.c @@ -0,0 +1,959 @@ +/* + * Copyright (C) 2009 ST-Ericsson + * Copyright (C) 2009 STMicroelectronics + * + * I2C master mode controller driver, used in Nomadik 8815 + * and Ux500 platforms. + * + * Author: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> + * Author: Sachin Verma <sachin.verma@st.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2, as + * published by the Free Software Foundation. + */ +#include <linux/init.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/i2c.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/io.h> + +#include <plat/i2c.h> + +#define DRIVER_NAME "nmk-i2c" + +/* I2C Controller register offsets */ +#define I2C_CR (0x000) +#define I2C_SCR (0x004) +#define I2C_HSMCR (0x008) +#define I2C_MCR (0x00C) +#define I2C_TFR (0x010) +#define I2C_SR (0x014) +#define I2C_RFR (0x018) +#define I2C_TFTR (0x01C) +#define I2C_RFTR (0x020) +#define I2C_DMAR (0x024) +#define I2C_BRCR (0x028) +#define I2C_IMSCR (0x02C) +#define I2C_RISR (0x030) +#define I2C_MISR (0x034) +#define I2C_ICR (0x038) + +/* Control registers */ +#define I2C_CR_PE (0x1 << 0) /* Peripheral Enable */ +#define I2C_CR_OM (0x3 << 1) /* Operating mode */ +#define I2C_CR_SAM (0x1 << 3) /* Slave addressing mode */ +#define I2C_CR_SM (0x3 << 4) /* Speed mode */ +#define I2C_CR_SGCM (0x1 << 6) /* Slave general call mode */ +#define I2C_CR_FTX (0x1 << 7) /* Flush Transmit */ +#define I2C_CR_FRX (0x1 << 8) /* Flush Receive */ +#define I2C_CR_DMA_TX_EN (0x1 << 9) /* DMA Tx enable */ +#define I2C_CR_DMA_RX_EN (0x1 << 10) /* DMA Rx Enable */ +#define I2C_CR_DMA_SLE (0x1 << 11) /* DMA sync. logic enable */ +#define I2C_CR_LM (0x1 << 12) /* Loopback mode */ +#define I2C_CR_FON (0x3 << 13) /* Filtering on */ +#define I2C_CR_FS (0x3 << 15) /* Force stop enable */ + +/* Master controller (MCR) register */ +#define I2C_MCR_OP (0x1 << 0) /* Operation */ +#define I2C_MCR_A7 (0x7f << 1) /* 7-bit address */ +#define I2C_MCR_EA10 (0x7 << 8) /* 10-bit Extended address */ +#define I2C_MCR_SB (0x1 << 11) /* Extended address */ +#define I2C_MCR_AM (0x3 << 12) /* Address type */ +#define I2C_MCR_STOP (0x1 << 14) /* Stop condition */ +#define I2C_MCR_LENGTH (0x7ff << 15) /* Transaction length */ + +/* Status register (SR) */ +#define I2C_SR_OP (0x3 << 0) /* Operation */ +#define I2C_SR_STATUS (0x3 << 2) /* controller status */ +#define I2C_SR_CAUSE (0x7 << 4) /* Abort cause */ +#define I2C_SR_TYPE (0x3 << 7) /* Receive type */ +#define I2C_SR_LENGTH (0x7ff << 9) /* Transfer length */ + +/* Interrupt mask set/clear (IMSCR) bits */ +#define I2C_IT_TXFE (0x1 << 0) +#define I2C_IT_TXFNE (0x1 << 1) +#define I2C_IT_TXFF (0x1 << 2) +#define I2C_IT_TXFOVR (0x1 << 3) +#define I2C_IT_RXFE (0x1 << 4) +#define I2C_IT_RXFNF (0x1 << 5) +#define I2C_IT_RXFF (0x1 << 6) +#define I2C_IT_RFSR (0x1 << 16) +#define I2C_IT_RFSE (0x1 << 17) +#define I2C_IT_WTSR (0x1 << 18) +#define I2C_IT_MTD (0x1 << 19) +#define I2C_IT_STD (0x1 << 20) +#define I2C_IT_MAL (0x1 << 24) +#define I2C_IT_BERR (0x1 << 25) +#define I2C_IT_MTDWS (0x1 << 28) + +#define GEN_MASK(val, mask, sb) (((val) << (sb)) & (mask)) + +/* some bits in ICR are reserved */ +#define I2C_CLEAR_ALL_INTS 0x131f007f + +/* first three msb bits are reserved */ +#define IRQ_MASK(mask) (mask & 0x1fffffff) + +/* maximum threshold value */ +#define MAX_I2C_FIFO_THRESHOLD 15 + +enum i2c_status { + I2C_NOP, + I2C_ON_GOING, + I2C_OK, + I2C_ABORT +}; + +/* operation */ +enum i2c_operation { + I2C_NO_OPERATION = 0xff, + I2C_WRITE = 0x00, + I2C_READ = 0x01 +}; + +/* controller response timeout in ms */ +#define I2C_TIMEOUT_MS 500 + +/** + * struct i2c_nmk_client - client specific data + * @slave_adr: 7-bit slave address + * @count: no. bytes to be transfered + * @buffer: client data buffer + * @xfer_bytes: bytes transfered till now + * @operation: current I2C operation + */ +struct i2c_nmk_client { + unsigned short slave_adr; + unsigned long count; + unsigned char *buffer; + unsigned long xfer_bytes; + enum i2c_operation operation; +}; + +/** + * struct nmk_i2c_dev - private data structure of the controller + * @pdev: parent platform device + * @adap: corresponding I2C adapter + * @irq: interrupt line for the controller + * @virtbase: virtual io memory area + * @clk: hardware i2c block clock + * @cfg: machine provided controller configuration + * @cli: holder of client specific data + * @stop: stop condition + * @xfer_complete: acknowledge completion for a I2C message + * @result: controller propogated result + */ +struct nmk_i2c_dev { + struct platform_device *pdev; + struct i2c_adapter adap; + int irq; + void __iomem *virtbase; + struct clk *clk; + struct nmk_i2c_controller cfg; + struct i2c_nmk_client cli; + int stop; + struct completion xfer_complete; + int result; +}; + +/* controller's abort causes */ +static const char *abort_causes[] = { + "no ack received after address transmission", + "no ack received during data phase", + "ack received after xmission of master code", + "master lost arbitration", + "slave restarts", + "slave reset", + "overflow, maxsize is 2047 bytes", +}; + +static inline void i2c_set_bit(void __iomem *reg, u32 mask) +{ + writel(readl(reg) | mask, reg); +} + +static inline void i2c_clr_bit(void __iomem *reg, u32 mask) +{ + writel(readl(reg) & ~mask, reg); +} + +/** + * flush_i2c_fifo() - This function flushes the I2C FIFO + * @dev: private data of I2C Driver + * + * This function flushes the I2C Tx and Rx FIFOs. It returns + * 0 on successful flushing of FIFO + */ +static int flush_i2c_fifo(struct nmk_i2c_dev *dev) +{ +#define LOOP_ATTEMPTS 10 + int i; + unsigned long timeout; + + /* + * flush the transmit and receive FIFO. The flushing + * operation takes several cycles before to be completed. + * On the completion, the I2C internal logic clears these + * bits, until then no one must access Tx, Rx FIFO and + * should poll on these bits waiting for the completion. + */ + writel((I2C_CR_FTX | I2C_CR_FRX), dev->virtbase + I2C_CR); + + for (i = 0; i < LOOP_ATTEMPTS; i++) { + timeout = jiffies + msecs_to_jiffies(I2C_TIMEOUT_MS); + + while (!time_after(jiffies, timeout)) { + if ((readl(dev->virtbase + I2C_CR) & + (I2C_CR_FTX | I2C_CR_FRX)) == 0) + return 0; + } + } + + dev_err(&dev->pdev->dev, "flushing operation timed out " + "giving up after %d attempts", LOOP_ATTEMPTS); + + return -ETIMEDOUT; +} + +/** + * disable_all_interrupts() - Disable all interrupts of this I2c Bus + * @dev: private data of I2C Driver + */ +static void disable_all_interrupts(struct nmk_i2c_dev *dev) +{ + u32 mask = IRQ_MASK(0); + writel(mask, dev->virtbase + I2C_IMSCR); +} + +/** + * clear_all_interrupts() - Clear all interrupts of I2C Controller + * @dev: private data of I2C Driver + */ +static void clear_all_interrupts(struct nmk_i2c_dev *dev) +{ + u32 mask; + mask = IRQ_MASK(I2C_CLEAR_ALL_INTS); + writel(mask, dev->virtbase + I2C_ICR); +} + +/** + * init_hw() - initialize the I2C hardware + * @dev: private data of I2C Driver + */ +static int init_hw(struct nmk_i2c_dev *dev) +{ + int stat; + + stat = flush_i2c_fifo(dev); + if (stat) + return stat; + + /* disable the controller */ + i2c_clr_bit(dev->virtbase + I2C_CR , I2C_CR_PE); + + disable_all_interrupts(dev); + + clear_all_interrupts(dev); + + dev->cli.operation = I2C_NO_OPERATION; + + return 0; +} + +/* enable peripheral, master mode operation */ +#define DEFAULT_I2C_REG_CR ((1 << 1) | I2C_CR_PE) + +/** + * load_i2c_mcr_reg() - load the MCR register + * @dev: private data of controller + */ +static u32 load_i2c_mcr_reg(struct nmk_i2c_dev *dev) +{ + u32 mcr = 0; + + /* 7-bit address transaction */ + mcr |= GEN_MASK(1, I2C_MCR_AM, 12); + mcr |= GEN_MASK(dev->cli.slave_adr, I2C_MCR_A7, 1); + + /* start byte procedure not applied */ + mcr |= GEN_MASK(0, I2C_MCR_SB, 11); + + /* check the operation, master read/write? */ + if (dev->cli.operation == I2C_WRITE) + mcr |= GEN_MASK(I2C_WRITE, I2C_MCR_OP, 0); + else + mcr |= GEN_MASK(I2C_READ, I2C_MCR_OP, 0); + + /* stop or repeated start? */ + if (dev->stop) + mcr |= GEN_MASK(1, I2C_MCR_STOP, 14); + else + mcr &= ~(GEN_MASK(1, I2C_MCR_STOP, 14)); + + mcr |= GEN_MASK(dev->cli.count, I2C_MCR_LENGTH, 15); + + return mcr; +} + +/** + * setup_i2c_controller() - setup the controller + * @dev: private data of controller + */ +static void setup_i2c_controller(struct nmk_i2c_dev *dev) +{ + u32 brcr1, brcr2; + u32 i2c_clk, div; + + writel(0x0, dev->virtbase + I2C_CR); + writel(0x0, dev->virtbase + I2C_HSMCR); + writel(0x0, dev->virtbase + I2C_TFTR); + writel(0x0, dev->virtbase + I2C_RFTR); + writel(0x0, dev->virtbase + I2C_DMAR); + + /* + * set the slsu: + * + * slsu defines the data setup time after SCL clock + * stretching in terms of i2c clk cycles. The + * needed setup time for the three modes are 250ns, + * 100ns, 10ns repectively thus leading to the values + * of 14, 6, 2 for a 48 MHz i2c clk. + */ + writel(dev->cfg.slsu << 16, dev->virtbase + I2C_SCR); + + i2c_clk = clk_get_rate(dev->clk); + + /* fallback to std. mode if machine has not provided it */ + if (dev->cfg.clk_freq == 0) + dev->cfg.clk_freq = 100000; + + /* + * The spec says, in case of std. mode the divider is + * 2 whereas it is 3 for fast and fastplus mode of + * operation. TODO - high speed support. + */ + div = (dev->cfg.clk_freq > 100000) ? 3 : 2; + + /* + * generate the mask for baud rate counters. The controller + * has two baud rate counters. One is used for High speed + * operation, and the other is for std, fast mode, fast mode + * plus operation. Currently we do not supprt high speed mode + * so set brcr1 to 0. + */ + brcr1 = 0 << 16; + brcr2 = (i2c_clk/(dev->cfg.clk_freq * div)) & 0xffff; + + /* set the baud rate counter register */ + writel((brcr1 | brcr2), dev->virtbase + I2C_BRCR); + + /* + * set the speed mode. Currently we support + * only standard and fast mode of operation + * TODO - support for fast mode plus (upto 1Mb/s) + * and high speed (up to 3.4 Mb/s) + */ + if (dev->cfg.sm > I2C_FREQ_MODE_FAST) { + dev_err(&dev->pdev->dev, "do not support this mode " + "defaulting to std. mode\n"); + brcr2 = i2c_clk/(100000 * 2) & 0xffff; + writel((brcr1 | brcr2), dev->virtbase + I2C_BRCR); + writel(I2C_FREQ_MODE_STANDARD << 4, + dev->virtbase + I2C_CR); + } + writel(dev->cfg.sm << 4, dev->virtbase + I2C_CR); + + /* set the Tx and Rx FIFO threshold */ + writel(dev->cfg.tft, dev->virtbase + I2C_TFTR); + writel(dev->cfg.rft, dev->virtbase + I2C_RFTR); +} + +/** + * read_i2c() - Read from I2C client device + * @dev: private data of I2C Driver + * + * This function reads from i2c client device when controller is in + * master mode. There is a completion timeout. If there is no transfer + * before timeout error is returned. + */ +static int read_i2c(struct nmk_i2c_dev *dev) +{ + u32 status = 0; + u32 mcr; + u32 irq_mask = 0; + int timeout; + + mcr = load_i2c_mcr_reg(dev); + writel(mcr, dev->virtbase + I2C_MCR); + + /* load the current CR value */ + writel(readl(dev->virtbase + I2C_CR) | DEFAULT_I2C_REG_CR, + dev->virtbase + I2C_CR); + + /* enable the controller */ + i2c_set_bit(dev->virtbase + I2C_CR, I2C_CR_PE); + + init_completion(&dev->xfer_complete); + + /* enable interrupts by setting the mask */ + irq_mask = (I2C_IT_RXFNF | I2C_IT_RXFF | + I2C_IT_MAL | I2C_IT_BERR); + + if (dev->stop) + irq_mask |= I2C_IT_MTD; + else + irq_mask |= I2C_IT_MTDWS; + + irq_mask = I2C_CLEAR_ALL_INTS & IRQ_MASK(irq_mask); + + writel(readl(dev->virtbase + I2C_IMSCR) | irq_mask, + dev->virtbase + I2C_IMSCR); + + timeout = wait_for_completion_interruptible_timeout( + &dev->xfer_complete, msecs_to_jiffies(I2C_TIMEOUT_MS)); + + if (timeout < 0) { + dev_err(&dev->pdev->dev, + "wait_for_completion_interruptible_timeout" + "returned %d waiting for event\n", timeout); + status = timeout; + } + + if (timeout == 0) { + /* controler has timedout, re-init the h/w */ + dev_err(&dev->pdev->dev, "controller timed out, re-init h/w\n"); + (void) init_hw(dev); + status = -ETIMEDOUT; + } + + return status; +} + +/** + * write_i2c() - Write data to I2C client. + * @dev: private data of I2C Driver + * + * This function writes data to I2C client + */ +static int write_i2c(struct nmk_i2c_dev *dev) +{ + u32 status = 0; + u32 mcr; + u32 irq_mask = 0; + int timeout; + + mcr = load_i2c_mcr_reg(dev); + + writel(mcr, dev->virtbase + I2C_MCR); + + /* load the current CR value */ + writel(readl(dev->virtbase + I2C_CR) | DEFAULT_I2C_REG_CR, + dev->virtbase + I2C_CR); + + /* enable the controller */ + i2c_set_bit(dev->virtbase + I2C_CR , I2C_CR_PE); + + init_completion(&dev->xfer_complete); + + /* enable interrupts by settings the masks */ + irq_mask = (I2C_IT_TXFNE | I2C_IT_TXFOVR | + I2C_IT_MAL | I2C_IT_BERR); + + /* + * check if we want to transfer a single or multiple bytes, if so + * set the MTDWS bit (Master Transaction Done Without Stop) + * to start repeated start operation + */ + if (dev->stop) + irq_mask |= I2C_IT_MTD; + else + irq_mask |= I2C_IT_MTDWS; + + irq_mask = I2C_CLEAR_ALL_INTS & IRQ_MASK(irq_mask); + + writel(readl(dev->virtbase + I2C_IMSCR) | irq_mask, + dev->virtbase + I2C_IMSCR); + + timeout = wait_for_completion_interruptible_timeout( + &dev->xfer_complete, msecs_to_jiffies(I2C_TIMEOUT_MS)); + + if (timeout < 0) { + dev_err(&dev->pdev->dev, + "wait_for_completion_interruptible_timeout" + "returned %d waiting for event\n", timeout); + status = timeout; + } + + if (timeout == 0) { + /* controler has timedout, re-init the h/w */ + dev_err(&dev->pdev->dev, "controller timed out, re-init h/w\n"); + (void) init_hw(dev); + status = -ETIMEDOUT; + } + + return status; +} + +/** + * nmk_i2c_xfer() - I2C transfer function used by kernel framework + * @i2c_adap - Adapter pointer to the controller + * @msgs[] - Pointer to data to be written. + * @num_msgs - Number of messages to be executed + * + * This is the function called by the generic kernel i2c_transfer() + * or i2c_smbus...() API calls. Note that this code is protected by the + * semaphore set in the kernel i2c_transfer() function. + * + * NOTE: + * READ TRANSFER : We impose a restriction of the first message to be the + * index message for any read transaction. + * - a no index is coded as '0', + * - 2byte big endian index is coded as '3' + * !!! msg[0].buf holds the actual index. + * This is compatible with generic messages of smbus emulator + * that send a one byte index. + * eg. a I2C transation to read 2 bytes from index 0 + * idx = 0; + * msg[0].addr = client->addr; + * msg[0].flags = 0x0; + * msg[0].len = 1; + * msg[0].buf = &idx; + * + * msg[1].addr = client->addr; + * msg[1].flags = I2C_M_RD; + * msg[1].len = 2; + * msg[1].buf = rd_buff + * i2c_transfer(adap, msg, 2); + * + * WRITE TRANSFER : The I2C standard interface interprets all data as payload. + * If you want to emulate an SMBUS write transaction put the + * index as first byte(or first and second) in the payload. + * eg. a I2C transation to write 2 bytes from index 1 + * wr_buff[0] = 0x1; + * wr_buff[1] = 0x23; + * wr_buff[2] = 0x46; + * msg[0].flags = 0x0; + * msg[0].len = 3; + * msg[0].buf = wr_buff; + * i2c_transfer(adap, msg, 1); + * + * To read or write a block of data (multiple bytes) using SMBUS emulation + * please use the i2c_smbus_read_i2c_block_data() + * or i2c_smbus_write_i2c_block_data() API + */ +static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap, + struct i2c_msg msgs[], int num_msgs) +{ + int status; + int i; + u32 cause; + struct nmk_i2c_dev *dev = i2c_get_adapdata(i2c_adap); + + status = init_hw(dev); + if (status) + return status; + + /* setup the i2c controller */ + setup_i2c_controller(dev); + + for (i = 0; i < num_msgs; i++) { + if (unlikely(msgs[i].flags & I2C_M_TEN)) { + dev_err(&dev->pdev->dev, "10 bit addressing" + "not supported\n"); + return -EINVAL; + } + dev->cli.slave_adr = msgs[i].addr; + dev->cli.buffer = msgs[i].buf; + dev->cli.count = msgs[i].len; + dev->stop = (i < (num_msgs - 1)) ? 0 : 1; + dev->result = 0; + + if (msgs[i].flags & I2C_M_RD) { + /* it is a read operation */ + dev->cli.operation = I2C_READ; + status = read_i2c(dev); + } else { + /* write operation */ + dev->cli.operation = I2C_WRITE; + status = write_i2c(dev); + } + if (status || (dev->result)) { + /* get the abort cause */ + cause = (readl(dev->virtbase + I2C_SR) >> 4) & 0x7; + dev_err(&dev->pdev->dev, "error during I2C" + "message xfer: %d\n", cause); + dev_err(&dev->pdev->dev, "%s\n", + cause >= ARRAY_SIZE(abort_causes) + ? "unknown reason" : abort_causes[cause]); + return status; + } + mdelay(1); + } + /* return the no. messages processed */ + if (status) + return status; + else + return num_msgs; +} + +/** + * disable_interrupts() - disable the interrupts + * @dev: private data of controller + */ +static int disable_interrupts(struct nmk_i2c_dev *dev, u32 irq) +{ + irq = IRQ_MASK(irq); + writel(readl(dev->virtbase + I2C_IMSCR) & ~(I2C_CLEAR_ALL_INTS & irq), + dev->virtbase + I2C_IMSCR); + return 0; +} + +/** + * i2c_irq_handler() - interrupt routine + * @irq: interrupt number + * @arg: data passed to the handler + * + * This is the interrupt handler for the i2c driver. Currently + * it handles the major interrupts like Rx & Tx FIFO management + * interrupts, master transaction interrupts, arbitration and + * bus error interrupts. The rest of the interrupts are treated as + * unhandled. + */ +static irqreturn_t i2c_irq_handler(int irq, void *arg) +{ + struct nmk_i2c_dev *dev = arg; + u32 tft, rft; + u32 count; + u32 misr; + u32 src = 0; + + /* load Tx FIFO and Rx FIFO threshold values */ + tft = readl(dev->virtbase + I2C_TFTR); + rft = readl(dev->virtbase + I2C_RFTR); + + /* read interrupt status register */ + misr = readl(dev->virtbase + I2C_MISR); + + src = __ffs(misr); + switch ((1 << src)) { + + /* Transmit FIFO nearly empty interrupt */ + case I2C_IT_TXFNE: + { + if (dev->cli.operation == I2C_READ) { + /* + * in read operation why do we care for writing? + * so disable the Transmit FIFO interrupt + */ + disable_interrupts(dev, I2C_IT_TXFNE); + } else { + for (count = (MAX_I2C_FIFO_THRESHOLD - tft - 2); + (count > 0) && + (dev->cli.count != 0); + count--) { + /* write to the Tx FIFO */ + writeb(*dev->cli.buffer, + dev->virtbase + I2C_TFR); + dev->cli.buffer++; + dev->cli.count--; + dev->cli.xfer_bytes++; + } + /* + * if done, close the transfer by disabling the + * corresponding TXFNE interrupt + */ + if (dev->cli.count == 0) + disable_interrupts(dev, I2C_IT_TXFNE); + } + } + break; + + /* + * Rx FIFO nearly full interrupt. + * This is set when the numer of entries in Rx FIFO is + * greater or equal than the threshold value programmed + * in RFT + */ + case I2C_IT_RXFNF: + for (count = rft; count > 0; count--) { + /* Read the Rx FIFO */ + *dev->cli.buffer = readb(dev->virtbase + I2C_RFR); + dev->cli.buffer++; + } + dev->cli.count -= rft; + dev->cli.xfer_bytes += rft; + break; + + /* Rx FIFO full */ + case I2C_IT_RXFF: + for (count = MAX_I2C_FIFO_THRESHOLD; count > 0; count--) { + *dev->cli.buffer = readb(dev->virtbase + I2C_RFR); + dev->cli.buffer++; + } + dev->cli.count -= MAX_I2C_FIFO_THRESHOLD; + dev->cli.xfer_bytes += MAX_I2C_FIFO_THRESHOLD; + break; + + /* Master Transaction Done with/without stop */ + case I2C_IT_MTD: + case I2C_IT_MTDWS: + if (dev->cli.operation == I2C_READ) { + while (!readl(dev->virtbase + I2C_RISR) & I2C_IT_RXFE) { + if (dev->cli.count == 0) + break; + *dev->cli.buffer = + readb(dev->virtbase + I2C_RFR); + dev->cli.buffer++; + dev->cli.count--; + dev->cli.xfer_bytes++; + } + } + + i2c_set_bit(dev->virtbase + I2C_ICR, I2C_IT_MTD); + i2c_set_bit(dev->virtbase + I2C_ICR, I2C_IT_MTDWS); + + disable_interrupts(dev, + (I2C_IT_TXFNE | I2C_IT_TXFE | I2C_IT_TXFF + | I2C_IT_TXFOVR | I2C_IT_RXFNF + | I2C_IT_RXFF | I2C_IT_RXFE)); + + if (dev->cli.count) { + dev->result = -1; + dev_err(&dev->pdev->dev, "%lu bytes still remain to be" + "xfered\n", dev->cli.count); + (void) init_hw(dev); + } + complete(&dev->xfer_complete); + + break; + + /* Master Arbitration lost interrupt */ + case I2C_IT_MAL: + dev->result = -1; + (void) init_hw(dev); + + i2c_set_bit(dev->virtbase + I2C_ICR, I2C_IT_MAL); + complete(&dev->xfer_complete); + + break; + + /* + * Bus Error interrupt. + * This happens when an unexpected start/stop condition occurs + * during the transaction. + */ + case I2C_IT_BERR: + dev->result = -1; + /* get the status */ + if (((readl(dev->virtbase + I2C_SR) >> 2) & 0x3) == I2C_ABORT) + (void) init_hw(dev); + + i2c_set_bit(dev->virtbase + I2C_ICR, I2C_IT_BERR); + complete(&dev->xfer_complete); + + break; + + /* + * Tx FIFO overrun interrupt. + * This is set when a write operation in Tx FIFO is performed and + * the Tx FIFO is full. + */ + case I2C_IT_TXFOVR: + dev->result = -1; + (void) init_hw(dev); + + dev_err(&dev->pdev->dev, "Tx Fifo Over run\n"); + complete(&dev->xfer_complete); + + break; + + /* unhandled interrupts by this driver - TODO*/ + case I2C_IT_TXFE: + case I2C_IT_TXFF: + case I2C_IT_RXFE: + case I2C_IT_RFSR: + case I2C_IT_RFSE: + case I2C_IT_WTSR: + case I2C_IT_STD: + dev_err(&dev->pdev->dev, "unhandled Interrupt\n"); + break; + default: + dev_err(&dev->pdev->dev, "spurious Interrupt..\n"); + break; + } + + return IRQ_HANDLED; +} + +static unsigned int nmk_i2c_functionality(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C + | I2C_FUNC_SMBUS_BYTE_DATA + | I2C_FUNC_SMBUS_WORD_DATA + | I2C_FUNC_SMBUS_I2C_BLOCK; +} + +static const struct i2c_algorithm nmk_i2c_algo = { + .master_xfer = nmk_i2c_xfer, + .functionality = nmk_i2c_functionality +}; + +static int __devinit nmk_i2c_probe(struct platform_device *pdev) +{ + int ret = 0; + struct resource *res; + struct nmk_i2c_controller *pdata = + pdev->dev.platform_data; + struct nmk_i2c_dev *dev; + struct i2c_adapter *adap; + + dev = kzalloc(sizeof(struct nmk_i2c_dev), GFP_KERNEL); + if (!dev) { + dev_err(&pdev->dev, "cannot allocate memory\n"); + ret = -ENOMEM; + goto err_no_mem; + } + + dev->pdev = pdev; + platform_set_drvdata(pdev, dev); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + ret = -ENOENT; + goto err_no_resource; + } + + if (request_mem_region(res->start, resource_size(res), + DRIVER_NAME "I/O region") == NULL) { + ret = -EBUSY; + goto err_no_region; + } + + dev->virtbase = ioremap(res->start, resource_size(res)); + if (!dev->virtbase) { + ret = -ENOMEM; + goto err_no_ioremap; + } + + dev->irq = platform_get_irq(pdev, 0); + ret = request_irq(dev->irq, i2c_irq_handler, IRQF_DISABLED, + DRIVER_NAME, dev); + if (ret) { + dev_err(&pdev->dev, "cannot claim the irq %d\n", dev->irq); + goto err_irq; + } + + dev->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(dev->clk)) { + dev_err(&pdev->dev, "could not get i2c clock\n"); + ret = PTR_ERR(dev->clk); + goto err_no_clk; + } + + clk_enable(dev->clk); + + adap = &dev->adap; + adap->dev.parent = &pdev->dev; + adap->owner = THIS_MODULE; + adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; + adap->algo = &nmk_i2c_algo; + + /* fetch the controller id */ + adap->nr = pdev->id; + + /* fetch the controller configuration from machine */ + dev->cfg.clk_freq = pdata->clk_freq; + dev->cfg.slsu = pdata->slsu; + dev->cfg.tft = pdata->tft; + dev->cfg.rft = pdata->rft; + dev->cfg.sm = pdata->sm; + + i2c_set_adapdata(adap, dev); + + ret = init_hw(dev); + if (ret != 0) { + dev_err(&pdev->dev, "error in initializing i2c hardware\n"); + goto err_init_hw; + } + + dev_dbg(&pdev->dev, "initialize I2C%d bus on virtual " + "base %p\n", pdev->id, dev->virtbase); + + ret = i2c_add_numbered_adapter(adap); + if (ret) { + dev_err(&pdev->dev, "failed to add adapter\n"); + goto err_add_adap; + } + + return 0; + + err_init_hw: + clk_disable(dev->clk); + err_add_adap: + clk_put(dev->clk); + err_no_clk: + free_irq(dev->irq, dev); + err_irq: + iounmap(dev->virtbase); + err_no_ioremap: + release_mem_region(res->start, resource_size(res)); + err_no_region: + platform_set_drvdata(pdev, NULL); + err_no_resource: + kfree(dev); + err_no_mem: + + return ret; +} + +static int __devexit nmk_i2c_remove(struct platform_device *pdev) +{ + struct nmk_i2c_dev *dev = platform_get_drvdata(pdev); + + i2c_del_adapter(&dev->adap); + flush_i2c_fifo(dev); + disable_all_interrupts(dev); + clear_all_interrupts(dev); + /* disable the controller */ + i2c_clr_bit(dev->virtbase + I2C_CR, I2C_CR_PE); + free_irq(dev->irq, dev); + iounmap(dev->virtbase); + clk_disable(dev->clk); + clk_put(dev->clk); + platform_set_drvdata(pdev, NULL); + kfree(dev); + + return 0; +} + +static struct platform_driver nmk_i2c_driver = { + .driver = { + .owner = THIS_MODULE, + .name = DRIVER_NAME, + }, + .probe = nmk_i2c_probe, + .remove = __devexit_p(nmk_i2c_remove), +}; + +static int __init nmk_i2c_init(void) +{ + return platform_driver_register(&nmk_i2c_driver); +} + +static void __exit nmk_i2c_exit(void) +{ + platform_driver_unregister(&nmk_i2c_driver); +} + +subsys_initcall(nmk_i2c_init); +module_exit(nmk_i2c_exit); + +MODULE_AUTHOR("Sachin Verma, Srinidhi KASAGAR"); +MODULE_DESCRIPTION("Nomadik/Ux500 I2C driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:" DRIVER_NAME); diff --git a/drivers/i2c/busses/i2c-octeon.c b/drivers/i2c/busses/i2c-octeon.c new file mode 100644 index 00000000000..60375504fa4 --- /dev/null +++ b/drivers/i2c/busses/i2c-octeon.c @@ -0,0 +1,651 @@ +/* + * (C) Copyright 2009-2010 + * Nokia Siemens Networks, michael.lawnick.ext@nsn.com + * + * Portions Copyright (C) 2010 Cavium Networks, Inc. + * + * This is a driver for the i2c adapter in Cavium Networks' OCTEON processors. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/sched.h> +#include <linux/init.h> + +#include <linux/io.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/platform_device.h> + +#include <asm/octeon/octeon.h> + +#define DRV_NAME "i2c-octeon" + +/* The previous out-of-tree version was implicitly version 1.0. */ +#define DRV_VERSION "2.0" + +/* register offsets */ +#define SW_TWSI 0x00 +#define TWSI_INT 0x10 + +/* Controller command patterns */ +#define SW_TWSI_V 0x8000000000000000ull +#define SW_TWSI_EOP_TWSI_DATA 0x0C00000100000000ull +#define SW_TWSI_EOP_TWSI_CTL 0x0C00000200000000ull +#define SW_TWSI_EOP_TWSI_CLKCTL 0x0C00000300000000ull +#define SW_TWSI_EOP_TWSI_STAT 0x0C00000300000000ull +#define SW_TWSI_EOP_TWSI_RST 0x0C00000700000000ull +#define SW_TWSI_OP_TWSI_CLK 0x0800000000000000ull +#define SW_TWSI_R 0x0100000000000000ull + +/* Controller command and status bits */ +#define TWSI_CTL_CE 0x80 +#define TWSI_CTL_ENAB 0x40 +#define TWSI_CTL_STA 0x20 +#define TWSI_CTL_STP 0x10 +#define TWSI_CTL_IFLG 0x08 +#define TWSI_CTL_AAK 0x04 + +/* Some status values */ +#define STAT_START 0x08 +#define STAT_RSTART 0x10 +#define STAT_TXADDR_ACK 0x18 +#define STAT_TXDATA_ACK 0x28 +#define STAT_RXADDR_ACK 0x40 +#define STAT_RXDATA_ACK 0x50 +#define STAT_IDLE 0xF8 + +struct octeon_i2c { + wait_queue_head_t queue; + struct i2c_adapter adap; + int irq; + int twsi_freq; + int sys_freq; + resource_size_t twsi_phys; + void __iomem *twsi_base; + resource_size_t regsize; + struct device *dev; +}; + +/** + * octeon_i2c_write_sw - write an I2C core register. + * @i2c: The struct octeon_i2c. + * @eop_reg: Register selector. + * @data: Value to be written. + * + * The I2C core registers are accessed indirectly via the SW_TWSI CSR. + */ +static void octeon_i2c_write_sw(struct octeon_i2c *i2c, + u64 eop_reg, + u8 data) +{ + u64 tmp; + + __raw_writeq(SW_TWSI_V | eop_reg | data, i2c->twsi_base + SW_TWSI); + do { + tmp = __raw_readq(i2c->twsi_base + SW_TWSI); + } while ((tmp & SW_TWSI_V) != 0); +} + +/** + * octeon_i2c_read_sw - write an I2C core register. + * @i2c: The struct octeon_i2c. + * @eop_reg: Register selector. + * + * Returns the data. + * + * The I2C core registers are accessed indirectly via the SW_TWSI CSR. + */ +static u8 octeon_i2c_read_sw(struct octeon_i2c *i2c, u64 eop_reg) +{ + u64 tmp; + + __raw_writeq(SW_TWSI_V | eop_reg | SW_TWSI_R, i2c->twsi_base + SW_TWSI); + do { + tmp = __raw_readq(i2c->twsi_base + SW_TWSI); + } while ((tmp & SW_TWSI_V) != 0); + + return tmp & 0xFF; +} + +/** + * octeon_i2c_write_int - write the TWSI_INT register + * @i2c: The struct octeon_i2c. + * @data: Value to be written. + */ +static void octeon_i2c_write_int(struct octeon_i2c *i2c, u64 data) +{ + u64 tmp; + + __raw_writeq(data, i2c->twsi_base + TWSI_INT); + tmp = __raw_readq(i2c->twsi_base + TWSI_INT); +} + +/** + * octeon_i2c_int_enable - enable the TS interrupt. + * @i2c: The struct octeon_i2c. + * + * The interrupt will be asserted when there is non-STAT_IDLE state in + * the SW_TWSI_EOP_TWSI_STAT register. + */ +static void octeon_i2c_int_enable(struct octeon_i2c *i2c) +{ + octeon_i2c_write_int(i2c, 0x40); +} + +/** + * octeon_i2c_int_disable - disable the TS interrupt. + * @i2c: The struct octeon_i2c. + */ +static void octeon_i2c_int_disable(struct octeon_i2c *i2c) +{ + octeon_i2c_write_int(i2c, 0); +} + +/** + * octeon_i2c_unblock - unblock the bus. + * @i2c: The struct octeon_i2c. + * + * If there was a reset while a device was driving 0 to bus, + * bus is blocked. We toggle it free manually by some clock + * cycles and send a stop. + */ +static void octeon_i2c_unblock(struct octeon_i2c *i2c) +{ + int i; + + dev_dbg(i2c->dev, "%s\n", __func__); + for (i = 0; i < 9; i++) { + octeon_i2c_write_int(i2c, 0x0); + udelay(5); + octeon_i2c_write_int(i2c, 0x200); + udelay(5); + } + octeon_i2c_write_int(i2c, 0x300); + udelay(5); + octeon_i2c_write_int(i2c, 0x100); + udelay(5); + octeon_i2c_write_int(i2c, 0x0); +} + +/** + * octeon_i2c_isr - the interrupt service routine. + * @int: The irq, unused. + * @dev_id: Our struct octeon_i2c. + */ +static irqreturn_t octeon_i2c_isr(int irq, void *dev_id) +{ + struct octeon_i2c *i2c = dev_id; + + octeon_i2c_int_disable(i2c); + wake_up_interruptible(&i2c->queue); + + return IRQ_HANDLED; +} + + +static int octeon_i2c_test_iflg(struct octeon_i2c *i2c) +{ + return (octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_CTL) & TWSI_CTL_IFLG) != 0; +} + +/** + * octeon_i2c_wait - wait for the IFLG to be set. + * @i2c: The struct octeon_i2c. + * + * Returns 0 on success, otherwise a negative errno. + */ +static int octeon_i2c_wait(struct octeon_i2c *i2c) +{ + int result; + + octeon_i2c_int_enable(i2c); + + result = wait_event_interruptible_timeout(i2c->queue, + octeon_i2c_test_iflg(i2c), + i2c->adap.timeout); + + octeon_i2c_int_disable(i2c); + + if (result < 0) { + dev_dbg(i2c->dev, "%s: wait interrupted\n", __func__); + return result; + } else if (result == 0) { + dev_dbg(i2c->dev, "%s: timeout\n", __func__); + result = -ETIMEDOUT; + } + + return 0; +} + +/** + * octeon_i2c_start - send START to the bus. + * @i2c: The struct octeon_i2c. + * + * Returns 0 on success, otherwise a negative errno. + */ +static int octeon_i2c_start(struct octeon_i2c *i2c) +{ + u8 data; + int result; + + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, + TWSI_CTL_ENAB | TWSI_CTL_STA); + + result = octeon_i2c_wait(i2c); + if (result) { + if (octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT) == STAT_IDLE) { + /* + * Controller refused to send start flag May + * be a client is holding SDA low - let's try + * to free it. + */ + octeon_i2c_unblock(i2c); + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, + TWSI_CTL_ENAB | TWSI_CTL_STA); + + result = octeon_i2c_wait(i2c); + } + if (result) + return result; + } + + data = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT); + if ((data != STAT_START) && (data != STAT_RSTART)) { + dev_err(i2c->dev, "%s: bad status (0x%x)\n", __func__, data); + return -EIO; + } + + return 0; +} + +/** + * octeon_i2c_stop - send STOP to the bus. + * @i2c: The struct octeon_i2c. + * + * Returns 0 on success, otherwise a negative errno. + */ +static int octeon_i2c_stop(struct octeon_i2c *i2c) +{ + u8 data; + + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, + TWSI_CTL_ENAB | TWSI_CTL_STP); + + data = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT); + + if (data != STAT_IDLE) { + dev_err(i2c->dev, "%s: bad status(0x%x)\n", __func__, data); + return -EIO; + } + return 0; +} + +/** + * octeon_i2c_write - send data to the bus. + * @i2c: The struct octeon_i2c. + * @target: Target address. + * @data: Pointer to the data to be sent. + * @length: Length of the data. + * + * The address is sent over the bus, then the data. + * + * Returns 0 on success, otherwise a negative errno. + */ +static int octeon_i2c_write(struct octeon_i2c *i2c, int target, + const u8 *data, int length) +{ + int i, result; + u8 tmp; + + result = octeon_i2c_start(i2c); + if (result) + return result; + + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, target << 1); + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB); + + result = octeon_i2c_wait(i2c); + if (result) + return result; + + for (i = 0; i < length; i++) { + tmp = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT); + if ((tmp != STAT_TXADDR_ACK) && (tmp != STAT_TXDATA_ACK)) { + dev_err(i2c->dev, + "%s: bad status before write (0x%x)\n", + __func__, tmp); + return -EIO; + } + + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, data[i]); + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB); + + result = octeon_i2c_wait(i2c); + if (result) + return result; + } + + return 0; +} + +/** + * octeon_i2c_read - receive data from the bus. + * @i2c: The struct octeon_i2c. + * @target: Target address. + * @data: Pointer to the location to store the datae . + * @length: Length of the data. + * + * The address is sent over the bus, then the data is read. + * + * Returns 0 on success, otherwise a negative errno. + */ +static int octeon_i2c_read(struct octeon_i2c *i2c, int target, + u8 *data, int length) +{ + int i, result; + u8 tmp; + + if (length < 1) + return -EINVAL; + + result = octeon_i2c_start(i2c); + if (result) + return result; + + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, (target<<1) | 1); + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB); + + result = octeon_i2c_wait(i2c); + if (result) + return result; + + for (i = 0; i < length; i++) { + tmp = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT); + if ((tmp != STAT_RXDATA_ACK) && (tmp != STAT_RXADDR_ACK)) { + dev_err(i2c->dev, + "%s: bad status before read (0x%x)\n", + __func__, tmp); + return -EIO; + } + + if (i+1 < length) + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, + TWSI_CTL_ENAB | TWSI_CTL_AAK); + else + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, + TWSI_CTL_ENAB); + + result = octeon_i2c_wait(i2c); + if (result) + return result; + + data[i] = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_DATA); + } + return 0; +} + +/** + * octeon_i2c_xfer - The driver's master_xfer function. + * @adap: Pointer to the i2c_adapter structure. + * @msgs: Pointer to the messages to be processed. + * @num: Length of the MSGS array. + * + * Returns the number of messages processed, or a negative errno on + * failure. + */ +static int octeon_i2c_xfer(struct i2c_adapter *adap, + struct i2c_msg *msgs, + int num) +{ + struct i2c_msg *pmsg; + int i; + int ret = 0; + struct octeon_i2c *i2c = i2c_get_adapdata(adap); + + for (i = 0; ret == 0 && i < num; i++) { + pmsg = &msgs[i]; + dev_dbg(i2c->dev, + "Doing %s %d byte(s) to/from 0x%02x - %d of %d messages\n", + pmsg->flags & I2C_M_RD ? "read" : "write", + pmsg->len, pmsg->addr, i + 1, num); + if (pmsg->flags & I2C_M_RD) + ret = octeon_i2c_read(i2c, pmsg->addr, pmsg->buf, + pmsg->len); + else + ret = octeon_i2c_write(i2c, pmsg->addr, pmsg->buf, + pmsg->len); + } + octeon_i2c_stop(i2c); + + return (ret != 0) ? ret : num; +} + +static u32 octeon_i2c_functionality(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; +} + +static const struct i2c_algorithm octeon_i2c_algo = { + .master_xfer = octeon_i2c_xfer, + .functionality = octeon_i2c_functionality, +}; + +static struct i2c_adapter octeon_i2c_ops = { + .owner = THIS_MODULE, + .name = "OCTEON adapter", + .algo = &octeon_i2c_algo, + .timeout = 2, +}; + +/** + * octeon_i2c_setclock - Calculate and set clock divisors. + */ +static int __init octeon_i2c_setclock(struct octeon_i2c *i2c) +{ + int tclk, thp_base, inc, thp_idx, mdiv_idx, ndiv_idx, foscl, diff; + int thp = 0x18, mdiv = 2, ndiv = 0, delta_hz = 1000000; + + for (ndiv_idx = 0; ndiv_idx < 8 && delta_hz != 0; ndiv_idx++) { + /* + * An mdiv value of less than 2 seems to not work well + * with ds1337 RTCs, so we constrain it to larger + * values. + */ + for (mdiv_idx = 15; mdiv_idx >= 2 && delta_hz != 0; mdiv_idx--) { + /* + * For given ndiv and mdiv values check the + * two closest thp values. + */ + tclk = i2c->twsi_freq * (mdiv_idx + 1) * 10; + tclk *= (1 << ndiv_idx); + thp_base = (i2c->sys_freq / (tclk * 2)) - 1; + for (inc = 0; inc <= 1; inc++) { + thp_idx = thp_base + inc; + if (thp_idx < 5 || thp_idx > 0xff) + continue; + + foscl = i2c->sys_freq / (2 * (thp_idx + 1)); + foscl = foscl / (1 << ndiv_idx); + foscl = foscl / (mdiv_idx + 1) / 10; + diff = abs(foscl - i2c->twsi_freq); + if (diff < delta_hz) { + delta_hz = diff; + thp = thp_idx; + mdiv = mdiv_idx; + ndiv = ndiv_idx; + } + } + } + } + octeon_i2c_write_sw(i2c, SW_TWSI_OP_TWSI_CLK, thp); + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CLKCTL, (mdiv << 3) | ndiv); + + return 0; +} + +static int __init octeon_i2c_initlowlevel(struct octeon_i2c *i2c) +{ + u8 status; + int tries; + + /* disable high level controller, enable bus access */ + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB); + + /* reset controller */ + octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_RST, 0); + + for (tries = 10; tries; tries--) { + udelay(1); + status = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT); + if (status == STAT_IDLE) + return 0; + } + dev_err(i2c->dev, "%s: TWSI_RST failed! (0x%x)\n", __func__, status); + return -EIO; +} + +static int __devinit octeon_i2c_probe(struct platform_device *pdev) +{ + int irq, result = 0; + struct octeon_i2c *i2c; + struct octeon_i2c_data *i2c_data; + struct resource *res_mem; + + /* All adaptors have an irq. */ + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + i2c = kzalloc(sizeof(*i2c), GFP_KERNEL); + if (!i2c) { + dev_err(&pdev->dev, "kzalloc failed\n"); + result = -ENOMEM; + goto out; + } + i2c->dev = &pdev->dev; + i2c_data = pdev->dev.platform_data; + + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + + if (res_mem == NULL) { + dev_err(i2c->dev, "found no memory resource\n"); + result = -ENXIO; + goto fail_region; + } + + if (i2c_data == NULL) { + dev_err(i2c->dev, "no I2C frequency data\n"); + result = -ENXIO; + goto fail_region; + } + + i2c->twsi_phys = res_mem->start; + i2c->regsize = resource_size(res_mem); + i2c->twsi_freq = i2c_data->i2c_freq; + i2c->sys_freq = i2c_data->sys_freq; + + if (!request_mem_region(i2c->twsi_phys, i2c->regsize, res_mem->name)) { + dev_err(i2c->dev, "request_mem_region failed\n"); + goto fail_region; + } + i2c->twsi_base = ioremap(i2c->twsi_phys, i2c->regsize); + + init_waitqueue_head(&i2c->queue); + + i2c->irq = irq; + + result = request_irq(i2c->irq, octeon_i2c_isr, 0, DRV_NAME, i2c); + if (result < 0) { + dev_err(i2c->dev, "failed to attach interrupt\n"); + goto fail_irq; + } + + result = octeon_i2c_initlowlevel(i2c); + if (result) { + dev_err(i2c->dev, "init low level failed\n"); + goto fail_add; + } + + result = octeon_i2c_setclock(i2c); + if (result) { + dev_err(i2c->dev, "clock init failed\n"); + goto fail_add; + } + + i2c->adap = octeon_i2c_ops; + i2c->adap.dev.parent = &pdev->dev; + i2c->adap.nr = pdev->id >= 0 ? pdev->id : 0; + i2c_set_adapdata(&i2c->adap, i2c); + platform_set_drvdata(pdev, i2c); + + result = i2c_add_numbered_adapter(&i2c->adap); + if (result < 0) { + dev_err(i2c->dev, "failed to add adapter\n"); + goto fail_add; + } + + dev_info(i2c->dev, "version %s\n", DRV_VERSION); + + return result; + +fail_add: + platform_set_drvdata(pdev, NULL); + free_irq(i2c->irq, i2c); +fail_irq: + iounmap(i2c->twsi_base); + release_mem_region(i2c->twsi_phys, i2c->regsize); +fail_region: + kfree(i2c); +out: + return result; +}; + +static int __devexit octeon_i2c_remove(struct platform_device *pdev) +{ + struct octeon_i2c *i2c = platform_get_drvdata(pdev); + + i2c_del_adapter(&i2c->adap); + platform_set_drvdata(pdev, NULL); + free_irq(i2c->irq, i2c); + iounmap(i2c->twsi_base); + release_mem_region(i2c->twsi_phys, i2c->regsize); + kfree(i2c); + return 0; +}; + +static struct platform_driver octeon_i2c_driver = { + .probe = octeon_i2c_probe, + .remove = __devexit_p(octeon_i2c_remove), + .driver = { + .owner = THIS_MODULE, + .name = DRV_NAME, + }, +}; + +static int __init octeon_i2c_init(void) +{ + int rv; + + rv = platform_driver_register(&octeon_i2c_driver); + return rv; +} + +static void __exit octeon_i2c_exit(void) +{ + platform_driver_unregister(&octeon_i2c_driver); +} + +MODULE_AUTHOR("Michael Lawnick <michael.lawnick.ext@nsn.com>"); +MODULE_DESCRIPTION("I2C-Bus adapter for Cavium OCTEON processors"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); +MODULE_ALIAS("platform:" DRV_NAME); + +module_init(octeon_i2c_init); +module_exit(octeon_i2c_exit); diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 0037e31076b..913abd7c172 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -49,24 +49,24 @@ #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000)) #define OMAP_I2C_REV_REG 0x00 -#define OMAP_I2C_IE_REG 0x04 -#define OMAP_I2C_STAT_REG 0x08 -#define OMAP_I2C_IV_REG 0x0c +#define OMAP_I2C_IE_REG 0x01 +#define OMAP_I2C_STAT_REG 0x02 +#define OMAP_I2C_IV_REG 0x03 /* For OMAP3 I2C_IV has changed to I2C_WE (wakeup enable) */ -#define OMAP_I2C_WE_REG 0x0c -#define OMAP_I2C_SYSS_REG 0x10 -#define OMAP_I2C_BUF_REG 0x14 -#define OMAP_I2C_CNT_REG 0x18 -#define OMAP_I2C_DATA_REG 0x1c -#define OMAP_I2C_SYSC_REG 0x20 -#define OMAP_I2C_CON_REG 0x24 -#define OMAP_I2C_OA_REG 0x28 -#define OMAP_I2C_SA_REG 0x2c -#define OMAP_I2C_PSC_REG 0x30 -#define OMAP_I2C_SCLL_REG 0x34 -#define OMAP_I2C_SCLH_REG 0x38 -#define OMAP_I2C_SYSTEST_REG 0x3c -#define OMAP_I2C_BUFSTAT_REG 0x40 +#define OMAP_I2C_WE_REG 0x03 +#define OMAP_I2C_SYSS_REG 0x04 +#define OMAP_I2C_BUF_REG 0x05 +#define OMAP_I2C_CNT_REG 0x06 +#define OMAP_I2C_DATA_REG 0x07 +#define OMAP_I2C_SYSC_REG 0x08 +#define OMAP_I2C_CON_REG 0x09 +#define OMAP_I2C_OA_REG 0x0a +#define OMAP_I2C_SA_REG 0x0b +#define OMAP_I2C_PSC_REG 0x0c +#define OMAP_I2C_SCLL_REG 0x0d +#define OMAP_I2C_SCLH_REG 0x0e +#define OMAP_I2C_SYSTEST_REG 0x0f +#define OMAP_I2C_BUFSTAT_REG 0x10 /* I2C Interrupt Enable Register (OMAP_I2C_IE): */ #define OMAP_I2C_IE_XDR (1 << 14) /* TX Buffer drain int enable */ @@ -161,6 +161,7 @@ struct omap_i2c_dev { struct device *dev; void __iomem *base; /* virtual */ int irq; + int reg_shift; /* bit shift for I2C register addresses */ struct clk *iclk; /* Interface clock */ struct clk *fclk; /* Functional clock */ struct completion cmd_complete; @@ -189,12 +190,12 @@ struct omap_i2c_dev { static inline void omap_i2c_write_reg(struct omap_i2c_dev *i2c_dev, int reg, u16 val) { - __raw_writew(val, i2c_dev->base + reg); + __raw_writew(val, i2c_dev->base + (reg << i2c_dev->reg_shift)); } static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg) { - return __raw_readw(i2c_dev->base + reg); + return __raw_readw(i2c_dev->base + (reg << i2c_dev->reg_shift)); } static int __init omap_i2c_get_clocks(struct omap_i2c_dev *dev) @@ -924,6 +925,11 @@ omap_i2c_probe(struct platform_device *pdev) dev->b_hw = 1; /* Enable hardware fixes */ } + if (cpu_is_omap7xx()) + dev->reg_shift = 1; + else + dev->reg_shift = 2; + /* reset ASAP, clearing any IRQs */ omap_i2c_init(dev); diff --git a/drivers/i2c/busses/i2c-parport-light.c b/drivers/i2c/busses/i2c-parport-light.c index 322c5691e38..5f41ec0f72d 100644 --- a/drivers/i2c/busses/i2c-parport-light.c +++ b/drivers/i2c/busses/i2c-parport-light.c @@ -1,7 +1,7 @@ /* ------------------------------------------------------------------------ * * i2c-parport-light.c I2C bus over parallel port * * ------------------------------------------------------------------------ * - Copyright (C) 2003-2007 Jean Delvare <khali@linux-fr.org> + Copyright (C) 2003-2010 Jean Delvare <khali@linux-fr.org> Based on older i2c-velleman.c driver Copyright (C) 1995-2000 Simon G. Vogl @@ -27,10 +27,12 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/init.h> +#include <linux/delay.h> #include <linux/platform_device.h> #include <linux/ioport.h> #include <linux/i2c.h> #include <linux/i2c-algo-bit.h> +#include <linux/i2c-smbus.h> #include <asm/io.h> #include "i2c-parport.h" @@ -43,6 +45,10 @@ static u16 base; module_param(base, ushort, 0); MODULE_PARM_DESC(base, "Base I/O address"); +static int irq; +module_param(irq, int, 0); +MODULE_PARM_DESC(irq, "IRQ (optional)"); + /* ----- Low-level parallel port access ----------------------------------- */ static inline void port_write(unsigned char p, unsigned char d) @@ -119,6 +125,16 @@ static struct i2c_adapter parport_adapter = { .name = "Parallel port adapter (light)", }; +/* SMBus alert support */ +static struct i2c_smbus_alert_setup alert_data = { + .alert_edge_triggered = 1, +}; +static struct i2c_client *ara; +static struct lineop parport_ctrl_irq = { + .val = (1 << 4), + .port = CTRL, +}; + static int __devinit i2c_parport_probe(struct platform_device *pdev) { int err; @@ -127,18 +143,39 @@ static int __devinit i2c_parport_probe(struct platform_device *pdev) parport_setsda(NULL, 1); parport_setscl(NULL, 1); /* Other init if needed (power on...) */ - if (adapter_parm[type].init.val) + if (adapter_parm[type].init.val) { line_set(1, &adapter_parm[type].init); + /* Give powered devices some time to settle */ + msleep(100); + } parport_adapter.dev.parent = &pdev->dev; err = i2c_bit_add_bus(&parport_adapter); - if (err) + if (err) { dev_err(&pdev->dev, "Unable to register with I2C\n"); - return err; + return err; + } + + /* Setup SMBus alert if supported */ + if (adapter_parm[type].smbus_alert && irq) { + alert_data.irq = irq; + ara = i2c_setup_smbus_alert(&parport_adapter, &alert_data); + if (ara) + line_set(1, &parport_ctrl_irq); + else + dev_warn(&pdev->dev, "Failed to register ARA client\n"); + } + + return 0; } static int __devexit i2c_parport_remove(struct platform_device *pdev) { + if (ara) { + line_set(0, &parport_ctrl_irq); + i2c_unregister_device(ara); + ara = NULL; + } i2c_del_adapter(&parport_adapter); /* Un-init if needed (power off...) */ @@ -205,6 +242,9 @@ static int __init i2c_parport_init(void) if (!request_region(base, 3, DRVNAME)) return -EBUSY; + if (irq != 0) + pr_info(DRVNAME ": using irq %d\n", irq); + if (!adapter_parm[type].getscl.val) parport_algo_data.getscl = NULL; diff --git a/drivers/i2c/busses/i2c-parport.c b/drivers/i2c/busses/i2c-parport.c index 0d8998610c7..220fca7f23a 100644 --- a/drivers/i2c/busses/i2c-parport.c +++ b/drivers/i2c/busses/i2c-parport.c @@ -1,7 +1,7 @@ /* ------------------------------------------------------------------------ * * i2c-parport.c I2C bus over parallel port * * ------------------------------------------------------------------------ * - Copyright (C) 2003-2007 Jean Delvare <khali@linux-fr.org> + Copyright (C) 2003-2010 Jean Delvare <khali@linux-fr.org> Based on older i2c-philips-par.c driver Copyright (C) 1995-2000 Simon G. Vogl @@ -27,9 +27,11 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/init.h> +#include <linux/delay.h> #include <linux/parport.h> #include <linux/i2c.h> #include <linux/i2c-algo-bit.h> +#include <linux/i2c-smbus.h> #include "i2c-parport.h" /* ----- Device list ------------------------------------------------------ */ @@ -38,6 +40,8 @@ struct i2c_par { struct pardevice *pdev; struct i2c_adapter adapter; struct i2c_algo_bit_data algo_data; + struct i2c_smbus_alert_setup alert_data; + struct i2c_client *ara; struct i2c_par *next; }; @@ -143,6 +147,19 @@ static struct i2c_algo_bit_data parport_algo_data = { /* ----- I2c and parallel port call-back functions and structures --------- */ +void i2c_parport_irq(void *data) +{ + struct i2c_par *adapter = data; + struct i2c_client *ara = adapter->ara; + + if (ara) { + dev_dbg(&ara->dev, "SMBus alert received\n"); + i2c_handle_smbus_alert(ara); + } else + dev_dbg(&adapter->adapter.dev, + "SMBus alert received but no ARA client!\n"); +} + static void i2c_parport_attach (struct parport *port) { struct i2c_par *adapter; @@ -154,8 +171,9 @@ static void i2c_parport_attach (struct parport *port) } pr_debug("i2c-parport: attaching to %s\n", port->name); + parport_disable_irq(port); adapter->pdev = parport_register_device(port, "i2c-parport", - NULL, NULL, NULL, PARPORT_FLAG_EXCL, NULL); + NULL, NULL, i2c_parport_irq, PARPORT_FLAG_EXCL, adapter); if (!adapter->pdev) { printk(KERN_ERR "i2c-parport: Unable to register with parport\n"); goto ERROR0; @@ -185,14 +203,29 @@ static void i2c_parport_attach (struct parport *port) parport_setsda(port, 1); parport_setscl(port, 1); /* Other init if needed (power on...) */ - if (adapter_parm[type].init.val) + if (adapter_parm[type].init.val) { line_set(port, 1, &adapter_parm[type].init); + /* Give powered devices some time to settle */ + msleep(100); + } if (i2c_bit_add_bus(&adapter->adapter) < 0) { printk(KERN_ERR "i2c-parport: Unable to register with I2C\n"); goto ERROR1; } + /* Setup SMBus alert if supported */ + if (adapter_parm[type].smbus_alert) { + adapter->alert_data.alert_edge_triggered = 1; + adapter->ara = i2c_setup_smbus_alert(&adapter->adapter, + &adapter->alert_data); + if (adapter->ara) + parport_enable_irq(port); + else + printk(KERN_WARNING "i2c-parport: Failed to register " + "ARA client\n"); + } + /* Add the new adapter to the list */ adapter->next = adapter_list; adapter_list = adapter; @@ -213,6 +246,10 @@ static void i2c_parport_detach (struct parport *port) for (prev = NULL, adapter = adapter_list; adapter; prev = adapter, adapter = adapter->next) { if (adapter->pdev->port == port) { + if (adapter->ara) { + parport_disable_irq(port); + i2c_unregister_device(adapter->ara); + } i2c_del_adapter(&adapter->adapter); /* Un-init if needed (power off...) */ diff --git a/drivers/i2c/busses/i2c-parport.h b/drivers/i2c/busses/i2c-parport.h index ed69d846cb9..a9f66816546 100644 --- a/drivers/i2c/busses/i2c-parport.h +++ b/drivers/i2c/busses/i2c-parport.h @@ -1,7 +1,7 @@ /* ------------------------------------------------------------------------ * * i2c-parport.h I2C bus over parallel port * * ------------------------------------------------------------------------ * - Copyright (C) 2003-2004 Jean Delvare <khali@linux-fr.org> + Copyright (C) 2003-2010 Jean Delvare <khali@linux-fr.org> This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by @@ -38,6 +38,7 @@ struct adapter_parm { struct lineop getsda; struct lineop getscl; struct lineop init; + unsigned int smbus_alert:1; }; static struct adapter_parm adapter_parm[] = { @@ -73,6 +74,7 @@ static struct adapter_parm adapter_parm[] = { .setscl = { 0x01, DATA, 1 }, .getsda = { 0x10, STAT, 1 }, .init = { 0xf0, DATA, 0 }, + .smbus_alert = 1, }, /* type 5: ADM1025, ADM1030 and ADM1031 evaluation boards */ { diff --git a/drivers/i2c/busses/i2c-pasemi.c b/drivers/i2c/busses/i2c-pasemi.c index adf0fbb902f..0d20ff46a51 100644 --- a/drivers/i2c/busses/i2c-pasemi.c +++ b/drivers/i2c/busses/i2c-pasemi.c @@ -400,7 +400,7 @@ static void __devexit pasemi_smb_remove(struct pci_dev *dev) kfree(smbus); } -static struct pci_device_id pasemi_smb_ids[] = { +static const struct pci_device_id pasemi_smb_ids[] = { { PCI_DEVICE(0x1959, 0xa003) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index e56e4b6823c..ee9da6fcf69 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -472,7 +472,7 @@ static struct i2c_adapter piix4_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id piix4_ids[] = { +static const struct pci_device_id piix4_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3) }, { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3) }, { PCI_DEVICE(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_3) }, diff --git a/drivers/i2c/busses/i2c-pnx.c b/drivers/i2c/busses/i2c-pnx.c index 5d1c2603a13..9532dee6b58 100644 --- a/drivers/i2c/busses/i2c-pnx.c +++ b/drivers/i2c/busses/i2c-pnx.c @@ -20,15 +20,15 @@ #include <linux/platform_device.h> #include <linux/i2c-pnx.h> #include <linux/io.h> +#include <linux/err.h> +#include <linux/clk.h> + #include <mach/hardware.h> #include <mach/i2c.h> -#include <asm/irq.h> -#include <asm/uaccess.h> #define I2C_PNX_TIMEOUT 10 /* msec */ #define I2C_PNX_SPEED_KHZ 100 #define I2C_PNX_REGION_SIZE 0x100 -#define PNX_DEFAULT_FREQ 13 /* MHz */ static inline int wait_timeout(long timeout, struct i2c_pnx_algo_data *data) { @@ -50,22 +50,21 @@ static inline int wait_reset(long timeout, struct i2c_pnx_algo_data *data) return (timeout <= 0); } -static inline void i2c_pnx_arm_timer(struct i2c_adapter *adap) +static inline void i2c_pnx_arm_timer(struct i2c_pnx_algo_data *alg_data) { - struct i2c_pnx_algo_data *data = adap->algo_data; - struct timer_list *timer = &data->mif.timer; - int expires = I2C_PNX_TIMEOUT / (1000 / HZ); + struct timer_list *timer = &alg_data->mif.timer; + unsigned long expires = msecs_to_jiffies(I2C_PNX_TIMEOUT); if (expires <= 1) expires = 2; del_timer_sync(timer); - dev_dbg(&adap->dev, "Timer armed at %lu plus %u jiffies.\n", + dev_dbg(&alg_data->adapter.dev, "Timer armed at %lu plus %lu jiffies.\n", jiffies, expires); timer->expires = jiffies + expires; - timer->data = (unsigned long)adap; + timer->data = (unsigned long)&alg_data; add_timer(timer); } @@ -77,34 +76,34 @@ static inline void i2c_pnx_arm_timer(struct i2c_adapter *adap) * * Generate a START signal in the desired mode. */ -static int i2c_pnx_start(unsigned char slave_addr, struct i2c_adapter *adap) +static int i2c_pnx_start(unsigned char slave_addr, + struct i2c_pnx_algo_data *alg_data) { - struct i2c_pnx_algo_data *alg_data = adap->algo_data; - - dev_dbg(&adap->dev, "%s(): addr 0x%x mode %d\n", __func__, + dev_dbg(&alg_data->adapter.dev, "%s(): addr 0x%x mode %d\n", __func__, slave_addr, alg_data->mif.mode); /* Check for 7 bit slave addresses only */ if (slave_addr & ~0x7f) { - dev_err(&adap->dev, "%s: Invalid slave address %x. " - "Only 7-bit addresses are supported\n", - adap->name, slave_addr); + dev_err(&alg_data->adapter.dev, + "%s: Invalid slave address %x. Only 7-bit addresses are supported\n", + alg_data->adapter.name, slave_addr); return -EINVAL; } /* First, make sure bus is idle */ if (wait_timeout(I2C_PNX_TIMEOUT, alg_data)) { /* Somebody else is monopolizing the bus */ - dev_err(&adap->dev, "%s: Bus busy. Slave addr = %02x, " - "cntrl = %x, stat = %x\n", - adap->name, slave_addr, - ioread32(I2C_REG_CTL(alg_data)), - ioread32(I2C_REG_STS(alg_data))); + dev_err(&alg_data->adapter.dev, + "%s: Bus busy. Slave addr = %02x, cntrl = %x, stat = %x\n", + alg_data->adapter.name, slave_addr, + ioread32(I2C_REG_CTL(alg_data)), + ioread32(I2C_REG_STS(alg_data))); return -EBUSY; } else if (ioread32(I2C_REG_STS(alg_data)) & mstatus_afi) { /* Sorry, we lost the bus */ - dev_err(&adap->dev, "%s: Arbitration failure. " - "Slave addr = %02x\n", adap->name, slave_addr); + dev_err(&alg_data->adapter.dev, + "%s: Arbitration failure. Slave addr = %02x\n", + alg_data->adapter.name, slave_addr); return -EIO; } @@ -115,14 +114,14 @@ static int i2c_pnx_start(unsigned char slave_addr, struct i2c_adapter *adap) iowrite32(ioread32(I2C_REG_STS(alg_data)) | mstatus_tdi | mstatus_afi, I2C_REG_STS(alg_data)); - dev_dbg(&adap->dev, "%s(): sending %#x\n", __func__, + dev_dbg(&alg_data->adapter.dev, "%s(): sending %#x\n", __func__, (slave_addr << 1) | start_bit | alg_data->mif.mode); /* Write the slave address, START bit and R/W bit */ iowrite32((slave_addr << 1) | start_bit | alg_data->mif.mode, I2C_REG_TX(alg_data)); - dev_dbg(&adap->dev, "%s(): exit\n", __func__); + dev_dbg(&alg_data->adapter.dev, "%s(): exit\n", __func__); return 0; } @@ -133,13 +132,12 @@ static int i2c_pnx_start(unsigned char slave_addr, struct i2c_adapter *adap) * * Generate a STOP signal to terminate the master transaction. */ -static void i2c_pnx_stop(struct i2c_adapter *adap) +static void i2c_pnx_stop(struct i2c_pnx_algo_data *alg_data) { - struct i2c_pnx_algo_data *alg_data = adap->algo_data; /* Only 1 msec max timeout due to interrupt context */ long timeout = 1000; - dev_dbg(&adap->dev, "%s(): entering: stat = %04x.\n", + dev_dbg(&alg_data->adapter.dev, "%s(): entering: stat = %04x.\n", __func__, ioread32(I2C_REG_STS(alg_data))); /* Write a STOP bit to TX FIFO */ @@ -153,7 +151,7 @@ static void i2c_pnx_stop(struct i2c_adapter *adap) timeout--; } - dev_dbg(&adap->dev, "%s(): exiting: stat = %04x.\n", + dev_dbg(&alg_data->adapter.dev, "%s(): exiting: stat = %04x.\n", __func__, ioread32(I2C_REG_STS(alg_data))); } @@ -163,36 +161,29 @@ static void i2c_pnx_stop(struct i2c_adapter *adap) * * Sends one byte of data to the slave */ -static int i2c_pnx_master_xmit(struct i2c_adapter *adap) +static int i2c_pnx_master_xmit(struct i2c_pnx_algo_data *alg_data) { - struct i2c_pnx_algo_data *alg_data = adap->algo_data; u32 val; - dev_dbg(&adap->dev, "%s(): entering: stat = %04x.\n", + dev_dbg(&alg_data->adapter.dev, "%s(): entering: stat = %04x.\n", __func__, ioread32(I2C_REG_STS(alg_data))); if (alg_data->mif.len > 0) { /* We still have something to talk about... */ val = *alg_data->mif.buf++; - if (alg_data->mif.len == 1) { - val |= stop_bit; - if (!alg_data->last) - val |= start_bit; - } - alg_data->mif.len--; iowrite32(val, I2C_REG_TX(alg_data)); - dev_dbg(&adap->dev, "%s(): xmit %#x [%d]\n", __func__, - val, alg_data->mif.len + 1); + dev_dbg(&alg_data->adapter.dev, "%s(): xmit %#x [%d]\n", + __func__, val, alg_data->mif.len + 1); if (alg_data->mif.len == 0) { if (alg_data->last) { /* Wait until the STOP is seen. */ if (wait_timeout(I2C_PNX_TIMEOUT, alg_data)) - dev_err(&adap->dev, "The bus is still " - "active after timeout\n"); + dev_err(&alg_data->adapter.dev, + "The bus is still active after timeout\n"); } /* Disable master interrupts */ iowrite32(ioread32(I2C_REG_CTL(alg_data)) & @@ -201,14 +192,15 @@ static int i2c_pnx_master_xmit(struct i2c_adapter *adap) del_timer_sync(&alg_data->mif.timer); - dev_dbg(&adap->dev, "%s(): Waking up xfer routine.\n", + dev_dbg(&alg_data->adapter.dev, + "%s(): Waking up xfer routine.\n", __func__); complete(&alg_data->mif.complete); } } else if (alg_data->mif.len == 0) { /* zero-sized transfer */ - i2c_pnx_stop(adap); + i2c_pnx_stop(alg_data); /* Disable master interrupts. */ iowrite32(ioread32(I2C_REG_CTL(alg_data)) & @@ -217,13 +209,14 @@ static int i2c_pnx_master_xmit(struct i2c_adapter *adap) /* Stop timer. */ del_timer_sync(&alg_data->mif.timer); - dev_dbg(&adap->dev, "%s(): Waking up xfer routine after " - "zero-xfer.\n", __func__); + dev_dbg(&alg_data->adapter.dev, + "%s(): Waking up xfer routine after zero-xfer.\n", + __func__); complete(&alg_data->mif.complete); } - dev_dbg(&adap->dev, "%s(): exiting: stat = %04x.\n", + dev_dbg(&alg_data->adapter.dev, "%s(): exiting: stat = %04x.\n", __func__, ioread32(I2C_REG_STS(alg_data))); return 0; @@ -235,28 +228,23 @@ static int i2c_pnx_master_xmit(struct i2c_adapter *adap) * * Reads one byte data from the slave */ -static int i2c_pnx_master_rcv(struct i2c_adapter *adap) +static int i2c_pnx_master_rcv(struct i2c_pnx_algo_data *alg_data) { - struct i2c_pnx_algo_data *alg_data = adap->algo_data; unsigned int val = 0; u32 ctl = 0; - dev_dbg(&adap->dev, "%s(): entering: stat = %04x.\n", + dev_dbg(&alg_data->adapter.dev, "%s(): entering: stat = %04x.\n", __func__, ioread32(I2C_REG_STS(alg_data))); /* Check, whether there is already data, * or we didn't 'ask' for it yet. */ if (ioread32(I2C_REG_STS(alg_data)) & mstatus_rfe) { - dev_dbg(&adap->dev, "%s(): Write dummy data to fill " - "Rx-fifo...\n", __func__); + dev_dbg(&alg_data->adapter.dev, + "%s(): Write dummy data to fill Rx-fifo...\n", + __func__); if (alg_data->mif.len == 1) { - /* Last byte, do not acknowledge next rcv. */ - val |= stop_bit; - if (!alg_data->last) - val |= start_bit; - /* * Enable interrupt RFDAIE (data in Rx fifo), * and disable DRMIE (need data for Tx) @@ -281,16 +269,16 @@ static int i2c_pnx_master_rcv(struct i2c_adapter *adap) if (alg_data->mif.len > 0) { val = ioread32(I2C_REG_RX(alg_data)); *alg_data->mif.buf++ = (u8) (val & 0xff); - dev_dbg(&adap->dev, "%s(): rcv 0x%x [%d]\n", __func__, val, - alg_data->mif.len); + dev_dbg(&alg_data->adapter.dev, "%s(): rcv 0x%x [%d]\n", + __func__, val, alg_data->mif.len); alg_data->mif.len--; if (alg_data->mif.len == 0) { if (alg_data->last) /* Wait until the STOP is seen. */ if (wait_timeout(I2C_PNX_TIMEOUT, alg_data)) - dev_err(&adap->dev, "The bus is still " - "active after timeout\n"); + dev_err(&alg_data->adapter.dev, + "The bus is still active after timeout\n"); /* Disable master interrupts */ ctl = ioread32(I2C_REG_CTL(alg_data)); @@ -304,7 +292,7 @@ static int i2c_pnx_master_rcv(struct i2c_adapter *adap) } } - dev_dbg(&adap->dev, "%s(): exiting: stat = %04x.\n", + dev_dbg(&alg_data->adapter.dev, "%s(): exiting: stat = %04x.\n", __func__, ioread32(I2C_REG_STS(alg_data))); return 0; @@ -312,11 +300,11 @@ static int i2c_pnx_master_rcv(struct i2c_adapter *adap) static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id) { + struct i2c_pnx_algo_data *alg_data = dev_id; u32 stat, ctl; - struct i2c_adapter *adap = dev_id; - struct i2c_pnx_algo_data *alg_data = adap->algo_data; - dev_dbg(&adap->dev, "%s(): mstat = %x mctrl = %x, mode = %d\n", + dev_dbg(&alg_data->adapter.dev, + "%s(): mstat = %x mctrl = %x, mode = %d\n", __func__, ioread32(I2C_REG_STS(alg_data)), ioread32(I2C_REG_CTL(alg_data)), @@ -339,10 +327,10 @@ static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id) complete(&alg_data->mif.complete); } else if (stat & mstatus_nai) { /* Slave did not acknowledge, generate a STOP */ - dev_dbg(&adap->dev, "%s(): " - "Slave did not acknowledge, generating a STOP.\n", + dev_dbg(&alg_data->adapter.dev, + "%s(): Slave did not acknowledge, generating a STOP.\n", __func__); - i2c_pnx_stop(adap); + i2c_pnx_stop(alg_data); /* Disable master interrupts. */ ctl = ioread32(I2C_REG_CTL(alg_data)); @@ -368,9 +356,9 @@ static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id) */ if ((stat & mstatus_drmi) || !(stat & mstatus_rfe)) { if (alg_data->mif.mode == I2C_SMBUS_WRITE) { - i2c_pnx_master_xmit(adap); + i2c_pnx_master_xmit(alg_data); } else if (alg_data->mif.mode == I2C_SMBUS_READ) { - i2c_pnx_master_rcv(adap); + i2c_pnx_master_rcv(alg_data); } } } @@ -379,7 +367,8 @@ static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id) stat = ioread32(I2C_REG_STS(alg_data)); iowrite32(stat | mstatus_tdi | mstatus_afi, I2C_REG_STS(alg_data)); - dev_dbg(&adap->dev, "%s(): exiting, stat = %x ctrl = %x.\n", + dev_dbg(&alg_data->adapter.dev, + "%s(): exiting, stat = %x ctrl = %x.\n", __func__, ioread32(I2C_REG_STS(alg_data)), ioread32(I2C_REG_CTL(alg_data))); @@ -388,14 +377,13 @@ static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id) static void i2c_pnx_timeout(unsigned long data) { - struct i2c_adapter *adap = (struct i2c_adapter *)data; - struct i2c_pnx_algo_data *alg_data = adap->algo_data; + struct i2c_pnx_algo_data *alg_data = (struct i2c_pnx_algo_data *)data; u32 ctl; - dev_err(&adap->dev, "Master timed out. stat = %04x, cntrl = %04x. " - "Resetting master...\n", - ioread32(I2C_REG_STS(alg_data)), - ioread32(I2C_REG_CTL(alg_data))); + dev_err(&alg_data->adapter.dev, + "Master timed out. stat = %04x, cntrl = %04x. Resetting master...\n", + ioread32(I2C_REG_STS(alg_data)), + ioread32(I2C_REG_CTL(alg_data))); /* Reset master and disable interrupts */ ctl = ioread32(I2C_REG_CTL(alg_data)); @@ -409,15 +397,14 @@ static void i2c_pnx_timeout(unsigned long data) complete(&alg_data->mif.complete); } -static inline void bus_reset_if_active(struct i2c_adapter *adap) +static inline void bus_reset_if_active(struct i2c_pnx_algo_data *alg_data) { - struct i2c_pnx_algo_data *alg_data = adap->algo_data; u32 stat; if ((stat = ioread32(I2C_REG_STS(alg_data))) & mstatus_active) { - dev_err(&adap->dev, + dev_err(&alg_data->adapter.dev, "%s: Bus is still active after xfer. Reset it...\n", - adap->name); + alg_data->adapter.name); iowrite32(ioread32(I2C_REG_CTL(alg_data)) | mcntrl_reset, I2C_REG_CTL(alg_data)); wait_reset(I2C_PNX_TIMEOUT, alg_data); @@ -451,10 +438,11 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) struct i2c_pnx_algo_data *alg_data = adap->algo_data; u32 stat = ioread32(I2C_REG_STS(alg_data)); - dev_dbg(&adap->dev, "%s(): entering: %d messages, stat = %04x.\n", + dev_dbg(&alg_data->adapter.dev, + "%s(): entering: %d messages, stat = %04x.\n", __func__, num, ioread32(I2C_REG_STS(alg_data))); - bus_reset_if_active(adap); + bus_reset_if_active(alg_data); /* Process transactions in a loop. */ for (i = 0; rc >= 0 && i < num; i++) { @@ -464,9 +452,9 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) addr = pmsg->addr; if (pmsg->flags & I2C_M_TEN) { - dev_err(&adap->dev, + dev_err(&alg_data->adapter.dev, "%s: 10 bits addr not supported!\n", - adap->name); + alg_data->adapter.name); rc = -EINVAL; break; } @@ -478,11 +466,10 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) alg_data->mif.ret = 0; alg_data->last = (i == num - 1); - dev_dbg(&adap->dev, "%s(): mode %d, %d bytes\n", __func__, - alg_data->mif.mode, - alg_data->mif.len); + dev_dbg(&alg_data->adapter.dev, "%s(): mode %d, %d bytes\n", + __func__, alg_data->mif.mode, alg_data->mif.len); - i2c_pnx_arm_timer(adap); + i2c_pnx_arm_timer(alg_data); /* initialize the completion var */ init_completion(&alg_data->mif.complete); @@ -493,7 +480,7 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) I2C_REG_CTL(alg_data)); /* Put start-code and slave-address on the bus. */ - rc = i2c_pnx_start(addr, adap); + rc = i2c_pnx_start(addr, alg_data); if (rc < 0) break; @@ -502,31 +489,32 @@ i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) if (!(rc = alg_data->mif.ret)) completed++; - dev_dbg(&adap->dev, "%s(): Complete, return code = %d.\n", + dev_dbg(&alg_data->adapter.dev, + "%s(): Complete, return code = %d.\n", __func__, rc); /* Clear TDI and AFI bits in case they are set. */ if ((stat = ioread32(I2C_REG_STS(alg_data))) & mstatus_tdi) { - dev_dbg(&adap->dev, + dev_dbg(&alg_data->adapter.dev, "%s: TDI still set... clearing now.\n", - adap->name); + alg_data->adapter.name); iowrite32(stat, I2C_REG_STS(alg_data)); } if ((stat = ioread32(I2C_REG_STS(alg_data))) & mstatus_afi) { - dev_dbg(&adap->dev, + dev_dbg(&alg_data->adapter.dev, "%s: AFI still set... clearing now.\n", - adap->name); + alg_data->adapter.name); iowrite32(stat, I2C_REG_STS(alg_data)); } } - bus_reset_if_active(adap); + bus_reset_if_active(alg_data); /* Cleanup to be sure... */ alg_data->mif.buf = NULL; alg_data->mif.len = 0; - dev_dbg(&adap->dev, "%s(): exiting, stat = %x\n", + dev_dbg(&alg_data->adapter.dev, "%s(): exiting, stat = %x\n", __func__, ioread32(I2C_REG_STS(alg_data))); if (completed != num) @@ -545,69 +533,92 @@ static struct i2c_algorithm pnx_algorithm = { .functionality = i2c_pnx_func, }; +#ifdef CONFIG_PM static int i2c_pnx_controller_suspend(struct platform_device *pdev, pm_message_t state) { - struct i2c_pnx_data *i2c_pnx = platform_get_drvdata(pdev); - return i2c_pnx->suspend(pdev, state); + struct i2c_pnx_algo_data *alg_data = platform_get_drvdata(pdev); + + /* FIXME: shouldn't this be clk_disable? */ + clk_enable(alg_data->clk); + + return 0; } static int i2c_pnx_controller_resume(struct platform_device *pdev) { - struct i2c_pnx_data *i2c_pnx = platform_get_drvdata(pdev); - return i2c_pnx->resume(pdev); + struct i2c_pnx_algo_data *alg_data = platform_get_drvdata(pdev); + + return clk_enable(alg_data->clk); } +#else +#define i2c_pnx_controller_suspend NULL +#define i2c_pnx_controller_resume NULL +#endif static int __devinit i2c_pnx_probe(struct platform_device *pdev) { unsigned long tmp; int ret = 0; struct i2c_pnx_algo_data *alg_data; - int freq_mhz; + unsigned long freq; struct i2c_pnx_data *i2c_pnx = pdev->dev.platform_data; - if (!i2c_pnx || !i2c_pnx->adapter) { + if (!i2c_pnx || !i2c_pnx->name) { dev_err(&pdev->dev, "%s: no platform data supplied\n", __func__); ret = -EINVAL; goto out; } - platform_set_drvdata(pdev, i2c_pnx); - - if (i2c_pnx->calculate_input_freq) - freq_mhz = i2c_pnx->calculate_input_freq(pdev); - else { - freq_mhz = PNX_DEFAULT_FREQ; - dev_info(&pdev->dev, "Setting bus frequency to default value: " - "%d MHz\n", freq_mhz); + alg_data = kzalloc(sizeof(*alg_data), GFP_KERNEL); + if (!alg_data) { + ret = -ENOMEM; + goto err_kzalloc; } - i2c_pnx->adapter->algo = &pnx_algorithm; + platform_set_drvdata(pdev, alg_data); + + strlcpy(alg_data->adapter.name, i2c_pnx->name, + sizeof(alg_data->adapter.name)); + alg_data->adapter.dev.parent = &pdev->dev; + alg_data->adapter.algo = &pnx_algorithm; + alg_data->adapter.algo_data = alg_data; + alg_data->adapter.nr = pdev->id; + alg_data->i2c_pnx = i2c_pnx; + + alg_data->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(alg_data->clk)) { + ret = PTR_ERR(alg_data->clk); + goto out_drvdata; + } - alg_data = i2c_pnx->adapter->algo_data; init_timer(&alg_data->mif.timer); alg_data->mif.timer.function = i2c_pnx_timeout; - alg_data->mif.timer.data = (unsigned long)i2c_pnx->adapter; + alg_data->mif.timer.data = (unsigned long)alg_data; /* Register I/O resource */ - if (!request_mem_region(alg_data->base, I2C_PNX_REGION_SIZE, + if (!request_mem_region(i2c_pnx->base, I2C_PNX_REGION_SIZE, pdev->name)) { dev_err(&pdev->dev, "I/O region 0x%08x for I2C already in use.\n", - alg_data->base); + i2c_pnx->base); ret = -ENODEV; - goto out_drvdata; + goto out_clkget; } - if (!(alg_data->ioaddr = - (u32)ioremap(alg_data->base, I2C_PNX_REGION_SIZE))) { + alg_data->ioaddr = ioremap(i2c_pnx->base, I2C_PNX_REGION_SIZE); + if (!alg_data->ioaddr) { dev_err(&pdev->dev, "Couldn't ioremap I2C I/O region\n"); ret = -ENOMEM; goto out_release; } - i2c_pnx->set_clock_run(pdev); + ret = clk_enable(alg_data->clk); + if (ret) + goto out_unmap; + + freq = clk_get_rate(alg_data->clk); /* * Clock Divisor High This value is the number of system clocks @@ -620,45 +631,47 @@ static int __devinit i2c_pnx_probe(struct platform_device *pdev) * the deglitching filter length. */ - tmp = ((freq_mhz * 1000) / I2C_PNX_SPEED_KHZ) / 2 - 2; + tmp = ((freq / 1000) / I2C_PNX_SPEED_KHZ) / 2 - 2; iowrite32(tmp, I2C_REG_CKH(alg_data)); iowrite32(tmp, I2C_REG_CKL(alg_data)); iowrite32(mcntrl_reset, I2C_REG_CTL(alg_data)); if (wait_reset(I2C_PNX_TIMEOUT, alg_data)) { ret = -ENODEV; - goto out_unmap; + goto out_clock; } init_completion(&alg_data->mif.complete); - ret = request_irq(alg_data->irq, i2c_pnx_interrupt, - 0, pdev->name, i2c_pnx->adapter); + ret = request_irq(i2c_pnx->irq, i2c_pnx_interrupt, + 0, pdev->name, alg_data); if (ret) goto out_clock; /* Register this adapter with the I2C subsystem */ - i2c_pnx->adapter->dev.parent = &pdev->dev; - i2c_pnx->adapter->nr = pdev->id; - ret = i2c_add_numbered_adapter(i2c_pnx->adapter); + ret = i2c_add_numbered_adapter(&alg_data->adapter); if (ret < 0) { dev_err(&pdev->dev, "I2C: Failed to add bus\n"); goto out_irq; } dev_dbg(&pdev->dev, "%s: Master at %#8x, irq %d.\n", - i2c_pnx->adapter->name, alg_data->base, alg_data->irq); + alg_data->adapter.name, i2c_pnx->base, i2c_pnx->irq); return 0; out_irq: - free_irq(alg_data->irq, i2c_pnx->adapter); + free_irq(i2c_pnx->irq, alg_data); out_clock: - i2c_pnx->set_clock_stop(pdev); + clk_disable(alg_data->clk); out_unmap: - iounmap((void *)alg_data->ioaddr); + iounmap(alg_data->ioaddr); out_release: - release_mem_region(alg_data->base, I2C_PNX_REGION_SIZE); + release_mem_region(i2c_pnx->base, I2C_PNX_REGION_SIZE); +out_clkget: + clk_put(alg_data->clk); out_drvdata: + kfree(alg_data); +err_kzalloc: platform_set_drvdata(pdev, NULL); out: return ret; @@ -666,15 +679,16 @@ out: static int __devexit i2c_pnx_remove(struct platform_device *pdev) { - struct i2c_pnx_data *i2c_pnx = platform_get_drvdata(pdev); - struct i2c_adapter *adap = i2c_pnx->adapter; - struct i2c_pnx_algo_data *alg_data = adap->algo_data; - - free_irq(alg_data->irq, i2c_pnx->adapter); - i2c_del_adapter(adap); - i2c_pnx->set_clock_stop(pdev); - iounmap((void *)alg_data->ioaddr); - release_mem_region(alg_data->base, I2C_PNX_REGION_SIZE); + struct i2c_pnx_algo_data *alg_data = platform_get_drvdata(pdev); + struct i2c_pnx_data *i2c_pnx = alg_data->i2c_pnx; + + free_irq(i2c_pnx->irq, alg_data); + i2c_del_adapter(&alg_data->adapter); + clk_disable(alg_data->clk); + iounmap(alg_data->ioaddr); + release_mem_region(i2c_pnx->base, I2C_PNX_REGION_SIZE); + clk_put(alg_data->clk); + kfree(alg_data); platform_set_drvdata(pdev, NULL); return 0; diff --git a/drivers/i2c/busses/i2c-sis5595.c b/drivers/i2c/busses/i2c-sis5595.c index 844569f7d8b..55a71370c79 100644 --- a/drivers/i2c/busses/i2c-sis5595.c +++ b/drivers/i2c/busses/i2c-sis5595.c @@ -369,7 +369,7 @@ static struct i2c_adapter sis5595_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id sis5595_ids[] __devinitdata = { +static const struct pci_device_id sis5595_ids[] __devinitconst = { { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-sis630.c b/drivers/i2c/busses/i2c-sis630.c index 68cff7af701..2309c7f1bde 100644 --- a/drivers/i2c/busses/i2c-sis630.c +++ b/drivers/i2c/busses/i2c-sis630.c @@ -468,7 +468,7 @@ static struct i2c_adapter sis630_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id sis630_ids[] __devinitdata = { +static const struct pci_device_id sis630_ids[] __devinitconst = { { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503) }, { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC) }, { 0, } diff --git a/drivers/i2c/busses/i2c-sis96x.c b/drivers/i2c/busses/i2c-sis96x.c index 1649963b00d..d43d8f8943d 100644 --- a/drivers/i2c/busses/i2c-sis96x.c +++ b/drivers/i2c/busses/i2c-sis96x.c @@ -245,7 +245,7 @@ static struct i2c_adapter sis96x_adapter = { .algo = &smbus_algorithm, }; -static struct pci_device_id sis96x_ids[] = { +static const struct pci_device_id sis96x_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_SMBUS) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-tiny-usb.c b/drivers/i2c/busses/i2c-tiny-usb.c index e29b6d5ba8e..b5b1bbf37d3 100644 --- a/drivers/i2c/busses/i2c-tiny-usb.c +++ b/drivers/i2c/busses/i2c-tiny-usb.c @@ -31,11 +31,13 @@ #define CMD_I2C_IO_BEGIN (1<<0) #define CMD_I2C_IO_END (1<<1) -/* i2c bit delay, default is 10us -> 100kHz */ +/* i2c bit delay, default is 10us -> 100kHz max + (in practice, due to additional delays in the i2c bitbanging + code this results in a i2c clock of about 50kHz) */ static unsigned short delay = 10; module_param(delay, ushort, 0); -MODULE_PARM_DESC(delay, "bit delay in microseconds, " - "e.g. 10 for 100kHz (default is 100kHz)"); +MODULE_PARM_DESC(delay, "bit delay in microseconds " + "(default is 10us for 100kHz max)"); static int usb_read(struct i2c_adapter *adapter, int cmd, int value, int index, void *data, int len); @@ -137,7 +139,7 @@ static const struct i2c_algorithm usb_algorithm = { * Future Technology Devices International Ltd., later a pair was * bought from EZPrototypes */ -static struct usb_device_id i2c_tiny_usb_table [] = { +static const struct usb_device_id i2c_tiny_usb_table[] = { { USB_DEVICE(0x0403, 0xc631) }, /* FTDI */ { USB_DEVICE(0x1c40, 0x0534) }, /* EZPrototypes */ { } /* Terminating entry */ diff --git a/drivers/i2c/busses/i2c-via.c b/drivers/i2c/busses/i2c-via.c index 8b24f192103..de78283bddb 100644 --- a/drivers/i2c/busses/i2c-via.c +++ b/drivers/i2c/busses/i2c-via.c @@ -89,7 +89,7 @@ static struct i2c_adapter vt586b_adapter = { }; -static struct pci_device_id vt586b_ids[] __devinitdata = { +static const struct pci_device_id vt586b_ids[] __devinitconst = { { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-viapro.c b/drivers/i2c/busses/i2c-viapro.c index a84a909e123..d57292e5dae 100644 --- a/drivers/i2c/busses/i2c-viapro.c +++ b/drivers/i2c/busses/i2c-viapro.c @@ -444,7 +444,7 @@ release_region: return error; } -static struct pci_device_id vt596_ids[] = { +static const struct pci_device_id vt596_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596_3), .driver_data = SMBBA1 }, { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596B_3), diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c new file mode 100644 index 00000000000..eece39a5a30 --- /dev/null +++ b/drivers/i2c/busses/i2c-xiic.c @@ -0,0 +1,824 @@ +/* + * i2c-xiic.c + * Copyright (c) 2002-2007 Xilinx Inc. + * Copyright (c) 2009-2010 Intel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * This code was implemented by Mocean Laboratories AB when porting linux + * to the automotive development board Russellville. The copyright holder + * as seen in the header is Intel corporation. + * Mocean Laboratories forked off the GNU/Linux platform work into a + * separate company called Pelagicore AB, which commited the code to the + * kernel. + */ + +/* Supports: + * Xilinx IIC + */ +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/platform_device.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/wait.h> +#include <linux/i2c-xiic.h> +#include <linux/io.h> + +#define DRIVER_NAME "xiic-i2c" + +enum xilinx_i2c_state { + STATE_DONE, + STATE_ERROR, + STATE_START +}; + +/** + * struct xiic_i2c - Internal representation of the XIIC I2C bus + * @base: Memory base of the HW registers + * @wait: Wait queue for callers + * @adap: Kernel adapter representation + * @tx_msg: Messages from above to be sent + * @lock: Mutual exclusion + * @tx_pos: Current pos in TX message + * @nmsgs: Number of messages in tx_msg + * @state: See STATE_ + * @rx_msg: Current RX message + * @rx_pos: Position within current RX message + */ +struct xiic_i2c { + void __iomem *base; + wait_queue_head_t wait; + struct i2c_adapter adap; + struct i2c_msg *tx_msg; + spinlock_t lock; + unsigned int tx_pos; + unsigned int nmsgs; + enum xilinx_i2c_state state; + struct i2c_msg *rx_msg; + int rx_pos; +}; + + +#define XIIC_MSB_OFFSET 0 +#define XIIC_REG_OFFSET (0x100+XIIC_MSB_OFFSET) + +/* + * Register offsets in bytes from RegisterBase. Three is added to the + * base offset to access LSB (IBM style) of the word + */ +#define XIIC_CR_REG_OFFSET (0x00+XIIC_REG_OFFSET) /* Control Register */ +#define XIIC_SR_REG_OFFSET (0x04+XIIC_REG_OFFSET) /* Status Register */ +#define XIIC_DTR_REG_OFFSET (0x08+XIIC_REG_OFFSET) /* Data Tx Register */ +#define XIIC_DRR_REG_OFFSET (0x0C+XIIC_REG_OFFSET) /* Data Rx Register */ +#define XIIC_ADR_REG_OFFSET (0x10+XIIC_REG_OFFSET) /* Address Register */ +#define XIIC_TFO_REG_OFFSET (0x14+XIIC_REG_OFFSET) /* Tx FIFO Occupancy */ +#define XIIC_RFO_REG_OFFSET (0x18+XIIC_REG_OFFSET) /* Rx FIFO Occupancy */ +#define XIIC_TBA_REG_OFFSET (0x1C+XIIC_REG_OFFSET) /* 10 Bit Address reg */ +#define XIIC_RFD_REG_OFFSET (0x20+XIIC_REG_OFFSET) /* Rx FIFO Depth reg */ +#define XIIC_GPO_REG_OFFSET (0x24+XIIC_REG_OFFSET) /* Output Register */ + +/* Control Register masks */ +#define XIIC_CR_ENABLE_DEVICE_MASK 0x01 /* Device enable = 1 */ +#define XIIC_CR_TX_FIFO_RESET_MASK 0x02 /* Transmit FIFO reset=1 */ +#define XIIC_CR_MSMS_MASK 0x04 /* Master starts Txing=1 */ +#define XIIC_CR_DIR_IS_TX_MASK 0x08 /* Dir of tx. Txing=1 */ +#define XIIC_CR_NO_ACK_MASK 0x10 /* Tx Ack. NO ack = 1 */ +#define XIIC_CR_REPEATED_START_MASK 0x20 /* Repeated start = 1 */ +#define XIIC_CR_GENERAL_CALL_MASK 0x40 /* Gen Call enabled = 1 */ + +/* Status Register masks */ +#define XIIC_SR_GEN_CALL_MASK 0x01 /* 1=a mstr issued a GC */ +#define XIIC_SR_ADDR_AS_SLAVE_MASK 0x02 /* 1=when addr as slave */ +#define XIIC_SR_BUS_BUSY_MASK 0x04 /* 1 = bus is busy */ +#define XIIC_SR_MSTR_RDING_SLAVE_MASK 0x08 /* 1=Dir: mstr <-- slave */ +#define XIIC_SR_TX_FIFO_FULL_MASK 0x10 /* 1 = Tx FIFO full */ +#define XIIC_SR_RX_FIFO_FULL_MASK 0x20 /* 1 = Rx FIFO full */ +#define XIIC_SR_RX_FIFO_EMPTY_MASK 0x40 /* 1 = Rx FIFO empty */ +#define XIIC_SR_TX_FIFO_EMPTY_MASK 0x80 /* 1 = Tx FIFO empty */ + +/* Interrupt Status Register masks Interrupt occurs when... */ +#define XIIC_INTR_ARB_LOST_MASK 0x01 /* 1 = arbitration lost */ +#define XIIC_INTR_TX_ERROR_MASK 0x02 /* 1=Tx error/msg complete */ +#define XIIC_INTR_TX_EMPTY_MASK 0x04 /* 1 = Tx FIFO/reg empty */ +#define XIIC_INTR_RX_FULL_MASK 0x08 /* 1=Rx FIFO/reg=OCY level */ +#define XIIC_INTR_BNB_MASK 0x10 /* 1 = Bus not busy */ +#define XIIC_INTR_AAS_MASK 0x20 /* 1 = when addr as slave */ +#define XIIC_INTR_NAAS_MASK 0x40 /* 1 = not addr as slave */ +#define XIIC_INTR_TX_HALF_MASK 0x80 /* 1 = TX FIFO half empty */ + +/* The following constants specify the depth of the FIFOs */ +#define IIC_RX_FIFO_DEPTH 16 /* Rx fifo capacity */ +#define IIC_TX_FIFO_DEPTH 16 /* Tx fifo capacity */ + +/* The following constants specify groups of interrupts that are typically + * enabled or disables at the same time + */ +#define XIIC_TX_INTERRUPTS \ +(XIIC_INTR_TX_ERROR_MASK | XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_HALF_MASK) + +#define XIIC_TX_RX_INTERRUPTS (XIIC_INTR_RX_FULL_MASK | XIIC_TX_INTERRUPTS) + +/* The following constants are used with the following macros to specify the + * operation, a read or write operation. + */ +#define XIIC_READ_OPERATION 1 +#define XIIC_WRITE_OPERATION 0 + +/* + * Tx Fifo upper bit masks. + */ +#define XIIC_TX_DYN_START_MASK 0x0100 /* 1 = Set dynamic start */ +#define XIIC_TX_DYN_STOP_MASK 0x0200 /* 1 = Set dynamic stop */ + +/* + * The following constants define the register offsets for the Interrupt + * registers. There are some holes in the memory map for reserved addresses + * to allow other registers to be added and still match the memory map of the + * interrupt controller registers + */ +#define XIIC_DGIER_OFFSET 0x1C /* Device Global Interrupt Enable Register */ +#define XIIC_IISR_OFFSET 0x20 /* Interrupt Status Register */ +#define XIIC_IIER_OFFSET 0x28 /* Interrupt Enable Register */ +#define XIIC_RESETR_OFFSET 0x40 /* Reset Register */ + +#define XIIC_RESET_MASK 0xAUL + +/* + * The following constant is used for the device global interrupt enable + * register, to enable all interrupts for the device, this is the only bit + * in the register + */ +#define XIIC_GINTR_ENABLE_MASK 0x80000000UL + +#define xiic_tx_space(i2c) ((i2c)->tx_msg->len - (i2c)->tx_pos) +#define xiic_rx_space(i2c) ((i2c)->rx_msg->len - (i2c)->rx_pos) + +static void xiic_start_xfer(struct xiic_i2c *i2c); +static void __xiic_start_xfer(struct xiic_i2c *i2c); + +static inline void xiic_setreg8(struct xiic_i2c *i2c, int reg, u8 value) +{ + iowrite8(value, i2c->base + reg); +} + +static inline u8 xiic_getreg8(struct xiic_i2c *i2c, int reg) +{ + return ioread8(i2c->base + reg); +} + +static inline void xiic_setreg16(struct xiic_i2c *i2c, int reg, u16 value) +{ + iowrite16(value, i2c->base + reg); +} + +static inline void xiic_setreg32(struct xiic_i2c *i2c, int reg, int value) +{ + iowrite32(value, i2c->base + reg); +} + +static inline int xiic_getreg32(struct xiic_i2c *i2c, int reg) +{ + return ioread32(i2c->base + reg); +} + +static inline void xiic_irq_dis(struct xiic_i2c *i2c, u32 mask) +{ + u32 ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET); + xiic_setreg32(i2c, XIIC_IIER_OFFSET, ier & ~mask); +} + +static inline void xiic_irq_en(struct xiic_i2c *i2c, u32 mask) +{ + u32 ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET); + xiic_setreg32(i2c, XIIC_IIER_OFFSET, ier | mask); +} + +static inline void xiic_irq_clr(struct xiic_i2c *i2c, u32 mask) +{ + u32 isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET); + xiic_setreg32(i2c, XIIC_IISR_OFFSET, isr & mask); +} + +static inline void xiic_irq_clr_en(struct xiic_i2c *i2c, u32 mask) +{ + xiic_irq_clr(i2c, mask); + xiic_irq_en(i2c, mask); +} + +static void xiic_clear_rx_fifo(struct xiic_i2c *i2c) +{ + u8 sr; + for (sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET); + !(sr & XIIC_SR_RX_FIFO_EMPTY_MASK); + sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET)) + xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET); +} + +static void xiic_reinit(struct xiic_i2c *i2c) +{ + xiic_setreg32(i2c, XIIC_RESETR_OFFSET, XIIC_RESET_MASK); + + /* Set receive Fifo depth to maximum (zero based). */ + xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, IIC_RX_FIFO_DEPTH - 1); + + /* Reset Tx Fifo. */ + xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, XIIC_CR_TX_FIFO_RESET_MASK); + + /* Enable IIC Device, remove Tx Fifo reset & disable general call. */ + xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, XIIC_CR_ENABLE_DEVICE_MASK); + + /* make sure RX fifo is empty */ + xiic_clear_rx_fifo(i2c); + + /* Enable interrupts */ + xiic_setreg32(i2c, XIIC_DGIER_OFFSET, XIIC_GINTR_ENABLE_MASK); + + xiic_irq_clr_en(i2c, XIIC_INTR_AAS_MASK | XIIC_INTR_ARB_LOST_MASK); +} + +static void xiic_deinit(struct xiic_i2c *i2c) +{ + u8 cr; + + xiic_setreg32(i2c, XIIC_RESETR_OFFSET, XIIC_RESET_MASK); + + /* Disable IIC Device. */ + cr = xiic_getreg8(i2c, XIIC_CR_REG_OFFSET); + xiic_setreg8(i2c, XIIC_CR_REG_OFFSET, cr & ~XIIC_CR_ENABLE_DEVICE_MASK); +} + +static void xiic_read_rx(struct xiic_i2c *i2c) +{ + u8 bytes_in_fifo; + int i; + + bytes_in_fifo = xiic_getreg8(i2c, XIIC_RFO_REG_OFFSET) + 1; + + dev_dbg(i2c->adap.dev.parent, "%s entry, bytes in fifo: %d, msg: %d" + ", SR: 0x%x, CR: 0x%x\n", + __func__, bytes_in_fifo, xiic_rx_space(i2c), + xiic_getreg8(i2c, XIIC_SR_REG_OFFSET), + xiic_getreg8(i2c, XIIC_CR_REG_OFFSET)); + + if (bytes_in_fifo > xiic_rx_space(i2c)) + bytes_in_fifo = xiic_rx_space(i2c); + + for (i = 0; i < bytes_in_fifo; i++) + i2c->rx_msg->buf[i2c->rx_pos++] = + xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET); + + xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, + (xiic_rx_space(i2c) > IIC_RX_FIFO_DEPTH) ? + IIC_RX_FIFO_DEPTH - 1 : xiic_rx_space(i2c) - 1); +} + +static int xiic_tx_fifo_space(struct xiic_i2c *i2c) +{ + /* return the actual space left in the FIFO */ + return IIC_TX_FIFO_DEPTH - xiic_getreg8(i2c, XIIC_TFO_REG_OFFSET) - 1; +} + +static void xiic_fill_tx_fifo(struct xiic_i2c *i2c) +{ + u8 fifo_space = xiic_tx_fifo_space(i2c); + int len = xiic_tx_space(i2c); + + len = (len > fifo_space) ? fifo_space : len; + + dev_dbg(i2c->adap.dev.parent, "%s entry, len: %d, fifo space: %d\n", + __func__, len, fifo_space); + + while (len--) { + u16 data = i2c->tx_msg->buf[i2c->tx_pos++]; + if ((xiic_tx_space(i2c) == 0) && (i2c->nmsgs == 1)) { + /* last message in transfer -> STOP */ + data |= XIIC_TX_DYN_STOP_MASK; + dev_dbg(i2c->adap.dev.parent, "%s TX STOP\n", __func__); + + xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data); + } else + xiic_setreg8(i2c, XIIC_DTR_REG_OFFSET, data); + } +} + +static void xiic_wakeup(struct xiic_i2c *i2c, int code) +{ + i2c->tx_msg = NULL; + i2c->rx_msg = NULL; + i2c->nmsgs = 0; + i2c->state = code; + wake_up(&i2c->wait); +} + +static void xiic_process(struct xiic_i2c *i2c) +{ + u32 pend, isr, ier; + u32 clr = 0; + + /* Get the interrupt Status from the IPIF. There is no clearing of + * interrupts in the IPIF. Interrupts must be cleared at the source. + * To find which interrupts are pending; AND interrupts pending with + * interrupts masked. + */ + isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET); + ier = xiic_getreg32(i2c, XIIC_IIER_OFFSET); + pend = isr & ier; + + dev_dbg(i2c->adap.dev.parent, "%s entry, IER: 0x%x, ISR: 0x%x, " + "pend: 0x%x, SR: 0x%x, msg: %p, nmsgs: %d\n", + __func__, ier, isr, pend, xiic_getreg8(i2c, XIIC_SR_REG_OFFSET), + i2c->tx_msg, i2c->nmsgs); + + /* Do not processes a devices interrupts if the device has no + * interrupts pending + */ + if (!pend) + return; + + /* Service requesting interrupt */ + if ((pend & XIIC_INTR_ARB_LOST_MASK) || + ((pend & XIIC_INTR_TX_ERROR_MASK) && + !(pend & XIIC_INTR_RX_FULL_MASK))) { + /* bus arbritration lost, or... + * Transmit error _OR_ RX completed + * if this happens when RX_FULL is not set + * this is probably a TX error + */ + + dev_dbg(i2c->adap.dev.parent, "%s error\n", __func__); + + /* dynamic mode seem to suffer from problems if we just flushes + * fifos and the next message is a TX with len 0 (only addr) + * reset the IP instead of just flush fifos + */ + xiic_reinit(i2c); + + if (i2c->tx_msg) + xiic_wakeup(i2c, STATE_ERROR); + + } else if (pend & XIIC_INTR_RX_FULL_MASK) { + /* Receive register/FIFO is full */ + + clr = XIIC_INTR_RX_FULL_MASK; + if (!i2c->rx_msg) { + dev_dbg(i2c->adap.dev.parent, + "%s unexpexted RX IRQ\n", __func__); + xiic_clear_rx_fifo(i2c); + goto out; + } + + xiic_read_rx(i2c); + if (xiic_rx_space(i2c) == 0) { + /* this is the last part of the message */ + i2c->rx_msg = NULL; + + /* also clear TX error if there (RX complete) */ + clr |= (isr & XIIC_INTR_TX_ERROR_MASK); + + dev_dbg(i2c->adap.dev.parent, + "%s end of message, nmsgs: %d\n", + __func__, i2c->nmsgs); + + /* send next message if this wasn't the last, + * otherwise the transfer will be finialise when + * receiving the bus not busy interrupt + */ + if (i2c->nmsgs > 1) { + i2c->nmsgs--; + i2c->tx_msg++; + dev_dbg(i2c->adap.dev.parent, + "%s will start next...\n", __func__); + + __xiic_start_xfer(i2c); + } + } + } else if (pend & XIIC_INTR_BNB_MASK) { + /* IIC bus has transitioned to not busy */ + clr = XIIC_INTR_BNB_MASK; + + /* The bus is not busy, disable BusNotBusy interrupt */ + xiic_irq_dis(i2c, XIIC_INTR_BNB_MASK); + + if (!i2c->tx_msg) + goto out; + + if ((i2c->nmsgs == 1) && !i2c->rx_msg && + xiic_tx_space(i2c) == 0) + xiic_wakeup(i2c, STATE_DONE); + else + xiic_wakeup(i2c, STATE_ERROR); + + } else if (pend & (XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_HALF_MASK)) { + /* Transmit register/FIFO is empty or ½ empty */ + + clr = pend & + (XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_HALF_MASK); + + if (!i2c->tx_msg) { + dev_dbg(i2c->adap.dev.parent, + "%s unexpexted TX IRQ\n", __func__); + goto out; + } + + xiic_fill_tx_fifo(i2c); + + /* current message sent and there is space in the fifo */ + if (!xiic_tx_space(i2c) && xiic_tx_fifo_space(i2c) >= 2) { + dev_dbg(i2c->adap.dev.parent, + "%s end of message sent, nmsgs: %d\n", + __func__, i2c->nmsgs); + if (i2c->nmsgs > 1) { + i2c->nmsgs--; + i2c->tx_msg++; + __xiic_start_xfer(i2c); + } else { + xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK); + + dev_dbg(i2c->adap.dev.parent, + "%s Got TX IRQ but no more to do...\n", + __func__); + } + } else if (!xiic_tx_space(i2c) && (i2c->nmsgs == 1)) + /* current frame is sent and is last, + * make sure to disable tx half + */ + xiic_irq_dis(i2c, XIIC_INTR_TX_HALF_MASK); + } else { + /* got IRQ which is not acked */ + dev_err(i2c->adap.dev.parent, "%s Got unexpected IRQ\n", + __func__); + clr = pend; + } +out: + dev_dbg(i2c->adap.dev.parent, "%s clr: 0x%x\n", __func__, clr); + + xiic_setreg32(i2c, XIIC_IISR_OFFSET, clr); +} + +static int xiic_bus_busy(struct xiic_i2c *i2c) +{ + u8 sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET); + + return (sr & XIIC_SR_BUS_BUSY_MASK) ? -EBUSY : 0; +} + +static int xiic_busy(struct xiic_i2c *i2c) +{ + int tries = 3; + int err; + + if (i2c->tx_msg) + return -EBUSY; + + /* for instance if previous transfer was terminated due to TX error + * it might be that the bus is on it's way to become available + * give it at most 3 ms to wake + */ + err = xiic_bus_busy(i2c); + while (err && tries--) { + mdelay(1); + err = xiic_bus_busy(i2c); + } + + return err; +} + +static void xiic_start_recv(struct xiic_i2c *i2c) +{ + u8 rx_watermark; + struct i2c_msg *msg = i2c->rx_msg = i2c->tx_msg; + + /* Clear and enable Rx full interrupt. */ + xiic_irq_clr_en(i2c, XIIC_INTR_RX_FULL_MASK | XIIC_INTR_TX_ERROR_MASK); + + /* we want to get all but last byte, because the TX_ERROR IRQ is used + * to inidicate error ACK on the address, and negative ack on the last + * received byte, so to not mix them receive all but last. + * In the case where there is only one byte to receive + * we can check if ERROR and RX full is set at the same time + */ + rx_watermark = msg->len; + if (rx_watermark > IIC_RX_FIFO_DEPTH) + rx_watermark = IIC_RX_FIFO_DEPTH; + xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, rx_watermark - 1); + + if (!(msg->flags & I2C_M_NOSTART)) + /* write the address */ + xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, + (msg->addr << 1) | XIIC_READ_OPERATION | + XIIC_TX_DYN_START_MASK); + + xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK); + + xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, + msg->len | ((i2c->nmsgs == 1) ? XIIC_TX_DYN_STOP_MASK : 0)); + if (i2c->nmsgs == 1) + /* very last, enable bus not busy as well */ + xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK); + + /* the message is tx:ed */ + i2c->tx_pos = msg->len; +} + +static void xiic_start_send(struct xiic_i2c *i2c) +{ + struct i2c_msg *msg = i2c->tx_msg; + + xiic_irq_clr(i2c, XIIC_INTR_TX_ERROR_MASK); + + dev_dbg(i2c->adap.dev.parent, "%s entry, msg: %p, len: %d, " + "ISR: 0x%x, CR: 0x%x\n", + __func__, msg, msg->len, xiic_getreg32(i2c, XIIC_IISR_OFFSET), + xiic_getreg8(i2c, XIIC_CR_REG_OFFSET)); + + if (!(msg->flags & I2C_M_NOSTART)) { + /* write the address */ + u16 data = ((msg->addr << 1) & 0xfe) | XIIC_WRITE_OPERATION | + XIIC_TX_DYN_START_MASK; + if ((i2c->nmsgs == 1) && msg->len == 0) + /* no data and last message -> add STOP */ + data |= XIIC_TX_DYN_STOP_MASK; + + xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, data); + } + + xiic_fill_tx_fifo(i2c); + + /* Clear any pending Tx empty, Tx Error and then enable them. */ + xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK | XIIC_INTR_TX_ERROR_MASK | + XIIC_INTR_BNB_MASK); +} + +static irqreturn_t xiic_isr(int irq, void *dev_id) +{ + struct xiic_i2c *i2c = dev_id; + + spin_lock(&i2c->lock); + /* disable interrupts globally */ + xiic_setreg32(i2c, XIIC_DGIER_OFFSET, 0); + + dev_dbg(i2c->adap.dev.parent, "%s entry\n", __func__); + + xiic_process(i2c); + + xiic_setreg32(i2c, XIIC_DGIER_OFFSET, XIIC_GINTR_ENABLE_MASK); + spin_unlock(&i2c->lock); + + return IRQ_HANDLED; +} + +static void __xiic_start_xfer(struct xiic_i2c *i2c) +{ + int first = 1; + int fifo_space = xiic_tx_fifo_space(i2c); + dev_dbg(i2c->adap.dev.parent, "%s entry, msg: %p, fifos space: %d\n", + __func__, i2c->tx_msg, fifo_space); + + if (!i2c->tx_msg) + return; + + i2c->rx_pos = 0; + i2c->tx_pos = 0; + i2c->state = STATE_START; + while ((fifo_space >= 2) && (first || (i2c->nmsgs > 1))) { + if (!first) { + i2c->nmsgs--; + i2c->tx_msg++; + i2c->tx_pos = 0; + } else + first = 0; + + if (i2c->tx_msg->flags & I2C_M_RD) { + /* we dont date putting several reads in the FIFO */ + xiic_start_recv(i2c); + return; + } else { + xiic_start_send(i2c); + if (xiic_tx_space(i2c) != 0) { + /* the message could not be completely sent */ + break; + } + } + + fifo_space = xiic_tx_fifo_space(i2c); + } + + /* there are more messages or the current one could not be completely + * put into the FIFO, also enable the half empty interrupt + */ + if (i2c->nmsgs > 1 || xiic_tx_space(i2c)) + xiic_irq_clr_en(i2c, XIIC_INTR_TX_HALF_MASK); + +} + +static void xiic_start_xfer(struct xiic_i2c *i2c) +{ + unsigned long flags; + + spin_lock_irqsave(&i2c->lock, flags); + xiic_reinit(i2c); + /* disable interrupts globally */ + xiic_setreg32(i2c, XIIC_DGIER_OFFSET, 0); + spin_unlock_irqrestore(&i2c->lock, flags); + + __xiic_start_xfer(i2c); + xiic_setreg32(i2c, XIIC_DGIER_OFFSET, XIIC_GINTR_ENABLE_MASK); +} + +static int xiic_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) +{ + struct xiic_i2c *i2c = i2c_get_adapdata(adap); + int err; + + dev_dbg(adap->dev.parent, "%s entry SR: 0x%x\n", __func__, + xiic_getreg8(i2c, XIIC_SR_REG_OFFSET)); + + err = xiic_busy(i2c); + if (err) + return err; + + i2c->tx_msg = msgs; + i2c->nmsgs = num; + + xiic_start_xfer(i2c); + + if (wait_event_timeout(i2c->wait, (i2c->state == STATE_ERROR) || + (i2c->state == STATE_DONE), HZ)) + return (i2c->state == STATE_DONE) ? num : -EIO; + else { + i2c->tx_msg = NULL; + i2c->rx_msg = NULL; + i2c->nmsgs = 0; + return -ETIMEDOUT; + } +} + +static u32 xiic_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; +} + +static const struct i2c_algorithm xiic_algorithm = { + .master_xfer = xiic_xfer, + .functionality = xiic_func, +}; + +static struct i2c_adapter xiic_adapter = { + .owner = THIS_MODULE, + .name = DRIVER_NAME, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, + .algo = &xiic_algorithm, +}; + + +static int __devinit xiic_i2c_probe(struct platform_device *pdev) +{ + struct xiic_i2c *i2c; + struct xiic_i2c_platform_data *pdata; + struct resource *res; + int ret, irq; + u8 i; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + goto resource_missing; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + goto resource_missing; + + pdata = (struct xiic_i2c_platform_data *) pdev->dev.platform_data; + if (!pdata) + return -EINVAL; + + i2c = kzalloc(sizeof(*i2c), GFP_KERNEL); + if (!i2c) + return -ENOMEM; + + if (!request_mem_region(res->start, resource_size(res), pdev->name)) { + dev_err(&pdev->dev, "Memory region busy\n"); + ret = -EBUSY; + goto request_mem_failed; + } + + i2c->base = ioremap(res->start, resource_size(res)); + if (!i2c->base) { + dev_err(&pdev->dev, "Unable to map registers\n"); + ret = -EIO; + goto map_failed; + } + + /* hook up driver to tree */ + platform_set_drvdata(pdev, i2c); + i2c->adap = xiic_adapter; + i2c_set_adapdata(&i2c->adap, i2c); + i2c->adap.dev.parent = &pdev->dev; + + xiic_reinit(i2c); + + spin_lock_init(&i2c->lock); + init_waitqueue_head(&i2c->wait); + ret = request_irq(irq, xiic_isr, 0, pdev->name, i2c); + if (ret) { + dev_err(&pdev->dev, "Cannot claim IRQ\n"); + goto request_irq_failed; + } + + /* add i2c adapter to i2c tree */ + ret = i2c_add_adapter(&i2c->adap); + if (ret) { + dev_err(&pdev->dev, "Failed to add adapter\n"); + goto add_adapter_failed; + } + + /* add in known devices to the bus */ + for (i = 0; i < pdata->num_devices; i++) + i2c_new_device(&i2c->adap, pdata->devices + i); + + return 0; + +add_adapter_failed: + free_irq(irq, i2c); +request_irq_failed: + xiic_deinit(i2c); + iounmap(i2c->base); +map_failed: + release_mem_region(res->start, resource_size(res)); +request_mem_failed: + kfree(i2c); + + return ret; +resource_missing: + dev_err(&pdev->dev, "IRQ or Memory resource is missing\n"); + return -ENOENT; +} + +static int __devexit xiic_i2c_remove(struct platform_device* pdev) +{ + struct xiic_i2c *i2c = platform_get_drvdata(pdev); + struct resource *res; + + /* remove adapter & data */ + i2c_del_adapter(&i2c->adap); + + xiic_deinit(i2c); + + platform_set_drvdata(pdev, NULL); + + free_irq(platform_get_irq(pdev, 0), i2c); + + iounmap(i2c->base); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (res) + release_mem_region(res->start, resource_size(res)); + + kfree(i2c); + + return 0; +} + + +/* work with hotplug and coldplug */ +MODULE_ALIAS("platform:"DRIVER_NAME); + +static struct platform_driver xiic_i2c_driver = { + .probe = xiic_i2c_probe, + .remove = __devexit_p(xiic_i2c_remove), + .driver = { + .owner = THIS_MODULE, + .name = DRIVER_NAME, + }, +}; + +static int __init xiic_i2c_init(void) +{ + return platform_driver_register(&xiic_i2c_driver); +} + +static void __exit xiic_i2c_exit(void) +{ + platform_driver_unregister(&xiic_i2c_driver); +} + +module_init(xiic_i2c_init); +module_exit(xiic_i2c_exit); + +MODULE_AUTHOR("info@mocean-labs.com"); +MODULE_DESCRIPTION("Xilinx I2C bus driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 10be7b5fbe9..3202a86f420 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -34,6 +34,7 @@ #include <linux/hardirq.h> #include <linux/irqflags.h> #include <linux/rwsem.h> +#include <linux/pm_runtime.h> #include <asm/uaccess.h> #include "i2c-core.h" @@ -184,6 +185,52 @@ static int i2c_device_pm_resume(struct device *dev) #define i2c_device_pm_resume NULL #endif +#ifdef CONFIG_PM_RUNTIME +static int i2c_device_runtime_suspend(struct device *dev) +{ + const struct dev_pm_ops *pm; + + if (!dev->driver) + return 0; + pm = dev->driver->pm; + if (!pm || !pm->runtime_suspend) + return 0; + return pm->runtime_suspend(dev); +} + +static int i2c_device_runtime_resume(struct device *dev) +{ + const struct dev_pm_ops *pm; + + if (!dev->driver) + return 0; + pm = dev->driver->pm; + if (!pm || !pm->runtime_resume) + return 0; + return pm->runtime_resume(dev); +} + +static int i2c_device_runtime_idle(struct device *dev) +{ + const struct dev_pm_ops *pm = NULL; + int ret; + + if (dev->driver) + pm = dev->driver->pm; + if (pm && pm->runtime_idle) { + ret = pm->runtime_idle(dev); + if (ret) + return ret; + } + + return pm_runtime_suspend(dev); +} +#else +#define i2c_device_runtime_suspend NULL +#define i2c_device_runtime_resume NULL +#define i2c_device_runtime_idle NULL +#endif + static int i2c_device_suspend(struct device *dev, pm_message_t mesg) { struct i2c_client *client = i2c_verify_client(dev); @@ -251,6 +298,9 @@ static const struct attribute_group *i2c_dev_attr_groups[] = { static const struct dev_pm_ops i2c_device_pm_ops = { .suspend = i2c_device_pm_suspend, .resume = i2c_device_pm_resume, + .runtime_suspend = i2c_device_runtime_suspend, + .runtime_resume = i2c_device_runtime_resume, + .runtime_idle = i2c_device_runtime_idle, }; struct bus_type i2c_bus_type = { @@ -1133,7 +1183,7 @@ EXPORT_SYMBOL(i2c_transfer); * i2c_master_send - issue a single I2C message in master transmit mode * @client: Handle to slave device * @buf: Data that will be written to the slave - * @count: How many bytes to write + * @count: How many bytes to write, must be less than 64k since msg.len is u16 * * Returns negative errno, or else the number of bytes written. */ @@ -1160,7 +1210,7 @@ EXPORT_SYMBOL(i2c_master_send); * i2c_master_recv - issue a single I2C message in master receive mode * @client: Handle to slave device * @buf: Where to store data read from slave - * @count: How many bytes to read + * @count: How many bytes to read, must be less than 64k since msg.len is u16 * * Returns negative errno, or else the number of bytes read. */ diff --git a/drivers/i2c/i2c-smbus.c b/drivers/i2c/i2c-smbus.c new file mode 100644 index 00000000000..42127822124 --- /dev/null +++ b/drivers/i2c/i2c-smbus.c @@ -0,0 +1,263 @@ +/* + * i2c-smbus.c - SMBus extensions to the I2C protocol + * + * Copyright (C) 2008 David Brownell + * Copyright (C) 2010 Jean Delvare <khali@linux-fr.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/device.h> +#include <linux/semaphore.h> +#include <linux/interrupt.h> +#include <linux/workqueue.h> +#include <linux/i2c.h> +#include <linux/i2c-smbus.h> + +struct i2c_smbus_alert { + unsigned int alert_edge_triggered:1; + int irq; + struct work_struct alert; + struct i2c_client *ara; /* Alert response address */ +}; + +struct alert_data { + unsigned short addr; + u8 flag:1; +}; + +/* If this is the alerting device, notify its driver */ +static int smbus_do_alert(struct device *dev, void *addrp) +{ + struct i2c_client *client = i2c_verify_client(dev); + struct alert_data *data = addrp; + + if (!client || client->addr != data->addr) + return 0; + if (client->flags & I2C_CLIENT_TEN) + return 0; + + /* + * Drivers should either disable alerts, or provide at least + * a minimal handler. Lock so client->driver won't change. + */ + down(&dev->sem); + if (client->driver) { + if (client->driver->alert) + client->driver->alert(client, data->flag); + else + dev_warn(&client->dev, "no driver alert()!\n"); + } else + dev_dbg(&client->dev, "alert with no driver\n"); + up(&dev->sem); + + /* Stop iterating after we find the device */ + return -EBUSY; +} + +/* + * The alert IRQ handler needs to hand work off to a task which can issue + * SMBus calls, because those sleeping calls can't be made in IRQ context. + */ +static void smbus_alert(struct work_struct *work) +{ + struct i2c_smbus_alert *alert; + struct i2c_client *ara; + unsigned short prev_addr = 0; /* Not a valid address */ + + alert = container_of(work, struct i2c_smbus_alert, alert); + ara = alert->ara; + + for (;;) { + s32 status; + struct alert_data data; + + /* + * Devices with pending alerts reply in address order, low + * to high, because of slave transmit arbitration. After + * responding, an SMBus device stops asserting SMBALERT#. + * + * Note that SMBus 2.0 reserves 10-bit addresess for future + * use. We neither handle them, nor try to use PEC here. + */ + status = i2c_smbus_read_byte(ara); + if (status < 0) + break; + + data.flag = status & 1; + data.addr = status >> 1; + + if (data.addr == prev_addr) { + dev_warn(&ara->dev, "Duplicate SMBALERT# from dev " + "0x%02x, skipping\n", data.addr); + break; + } + dev_dbg(&ara->dev, "SMBALERT# from dev 0x%02x, flag %d\n", + data.addr, data.flag); + + /* Notify driver for the device which issued the alert */ + device_for_each_child(&ara->adapter->dev, &data, + smbus_do_alert); + prev_addr = data.addr; + } + + /* We handled all alerts; re-enable level-triggered IRQs */ + if (!alert->alert_edge_triggered) + enable_irq(alert->irq); +} + +static irqreturn_t smbalert_irq(int irq, void *d) +{ + struct i2c_smbus_alert *alert = d; + + /* Disable level-triggered IRQs until we handle them */ + if (!alert->alert_edge_triggered) + disable_irq_nosync(irq); + + schedule_work(&alert->alert); + return IRQ_HANDLED; +} + +/* Setup SMBALERT# infrastructure */ +static int smbalert_probe(struct i2c_client *ara, + const struct i2c_device_id *id) +{ + struct i2c_smbus_alert_setup *setup = ara->dev.platform_data; + struct i2c_smbus_alert *alert; + struct i2c_adapter *adapter = ara->adapter; + int res; + + alert = kzalloc(sizeof(struct i2c_smbus_alert), GFP_KERNEL); + if (!alert) + return -ENOMEM; + + alert->alert_edge_triggered = setup->alert_edge_triggered; + alert->irq = setup->irq; + INIT_WORK(&alert->alert, smbus_alert); + alert->ara = ara; + + if (setup->irq > 0) { + res = devm_request_irq(&ara->dev, setup->irq, smbalert_irq, + 0, "smbus_alert", alert); + if (res) { + kfree(alert); + return res; + } + } + + i2c_set_clientdata(ara, alert); + dev_info(&adapter->dev, "supports SMBALERT#, %s trigger\n", + setup->alert_edge_triggered ? "edge" : "level"); + + return 0; +} + +/* IRQ resource is managed so it is freed automatically */ +static int smbalert_remove(struct i2c_client *ara) +{ + struct i2c_smbus_alert *alert = i2c_get_clientdata(ara); + + cancel_work_sync(&alert->alert); + + i2c_set_clientdata(ara, NULL); + kfree(alert); + return 0; +} + +static const struct i2c_device_id smbalert_ids[] = { + { "smbus_alert", 0 }, + { /* LIST END */ } +}; +MODULE_DEVICE_TABLE(i2c, smbalert_ids); + +static struct i2c_driver smbalert_driver = { + .driver = { + .name = "smbus_alert", + }, + .probe = smbalert_probe, + .remove = smbalert_remove, + .id_table = smbalert_ids, +}; + +/** + * i2c_setup_smbus_alert - Setup SMBus alert support + * @adapter: the target adapter + * @setup: setup data for the SMBus alert handler + * Context: can sleep + * + * Setup handling of the SMBus alert protocol on a given I2C bus segment. + * + * Handling can be done either through our IRQ handler, or by the + * adapter (from its handler, periodic polling, or whatever). + * + * NOTE that if we manage the IRQ, we *MUST* know if it's level or + * edge triggered in order to hand it to the workqueue correctly. + * If triggering the alert seems to wedge the system, you probably + * should have said it's level triggered. + * + * This returns the ara client, which should be saved for later use with + * i2c_handle_smbus_alert() and ultimately i2c_unregister_device(); or NULL + * to indicate an error. + */ +struct i2c_client *i2c_setup_smbus_alert(struct i2c_adapter *adapter, + struct i2c_smbus_alert_setup *setup) +{ + struct i2c_board_info ara_board_info = { + I2C_BOARD_INFO("smbus_alert", 0x0c), + .platform_data = setup, + }; + + return i2c_new_device(adapter, &ara_board_info); +} +EXPORT_SYMBOL_GPL(i2c_setup_smbus_alert); + +/** + * i2c_handle_smbus_alert - Handle an SMBus alert + * @ara: the ARA client on the relevant adapter + * Context: can't sleep + * + * Helper function to be called from an I2C bus driver's interrupt + * handler. It will schedule the alert work, in turn calling the + * corresponding I2C device driver's alert function. + * + * It is assumed that ara is a valid i2c client previously returned by + * i2c_setup_smbus_alert(). + */ +int i2c_handle_smbus_alert(struct i2c_client *ara) +{ + struct i2c_smbus_alert *alert = i2c_get_clientdata(ara); + + return schedule_work(&alert->alert); +} +EXPORT_SYMBOL_GPL(i2c_handle_smbus_alert); + +static int __init i2c_smbus_init(void) +{ + return i2c_add_driver(&smbalert_driver); +} + +static void __exit i2c_smbus_exit(void) +{ + i2c_del_driver(&smbalert_driver); +} + +module_init(i2c_smbus_init); +module_exit(i2c_smbus_exit); + +MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>"); +MODULE_DESCRIPTION("SMBus protocol extensions support"); +MODULE_LICENSE("GPL"); |